summaryrefslogtreecommitdiff
path: root/drivers/video/omap2/displays/panel-taal.c
AgeCommit message (Collapse)Author
2011-07-01OMAP: DSS2: DSI: sync when disabling a displayTomi Valkeinen
When the panel driver calls omapdss_dsi_display_disable() it is possible that there are still some unsent packets in the TX fifo. Add dsi_sync_vc() calls in the beginning of omapdss_dsi_display_disable() to make sure the TX fifos are empty. This allows us to remove the msleep(10) hack from panel-taal.c Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01OMAP: DSS2: Taal: Make driver more fault tolerantTomi Valkeinen
If ULPS exit fails, and the following reset fails also, Taal driver was left in state where it thinks DSI is enabled while it really isn't, leading to crash. This patch checks the return value of taal_panel_reset, and if that fails, ulps_enabled is left true, causing the driver to retry ulps exit later. Also the return value of taal_wake_up is checked at taal_disable, and if wake up fails, we'll skip the power_off. This could leave the panel into a not-quite-valid state, but there's nothing we can do about it in that situation. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01OMAP: DSS2: remove update_mode from omapdssTomi Valkeinen
Remove the whole update_mode stuff from omapdss driver. If automatic update for manual update displays is needed, it's better implemented in higher layers. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12OMAP: DSS2: Taal: Use device name in backlight_device_registerArchit Taneja
Panel Taal driver uses the string "taal" to register for a backlight device. This causes backlight_device_register() to fail when a second taal panel is added. Use dev_name(&dssdev->dev) as a parameter instead of the string. Note: This will break backlight related sysfs commands. Use the name as generated by the DSS2 driver, in the form "displayi", which represents the ith registered display device. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12OMAP: DSS2: DSI: Add extra omap_dss_device argument in functions exported by dsiArchit Taneja
Add pointer to omap_dss_device struct as an argument in the functions which are exported to dsi panel drivers. This argument will tell the DSI driver which DSI interface's data it has to choose. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: Taal: Implement ULPS functionalityTomi Valkeinen
ULPS is a low power state where the DSI lanes are kept at ground. This patch implements ULPS by having a DSI bus inactivity timer which triggers the entry to ULPS. ULPS exit will happen automatically when the driver needs to do something on the DSI lanes. The ulps_timeout is configurable from board file or via sysfs. Additionally another sysfs file, "ulps", can be used to check the current ULPS state, or to manually enter or exit ULPS. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: Taal: Rename esd_wq to workqueueTomi Valkeinen
ESD workqueue will be shared with other functionality also. Rename "esd_wq" to "workqueue" to better reflect its usage. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: Taal: Separate panel resetTomi Valkeinen
Separate panel reset code to a function of its own. This will keep the code cleaner in the future when panel reset is called from multiple locations. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: Taal: Add sysfs file for ESD intervalTomi Valkeinen
Implement sysfs support to configure the ESD interval. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: Taal: Clean up ESD queueingTomi Valkeinen
Separate the code which queues/cancels ESD work into their own functions. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: Taal: Implement configurable ESD intervalTomi Valkeinen
ESD check in Taal driver is currently on/off feature with hardcoded interval. This patch changes it to a configurable interval, which can be set from the board file. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: DSI: add parameter to enter ulps on disableTomi Valkeinen
Add parameter to omapdss_dsi_display_disable() which the panel driver can use to tell if the DSI lanes should be put to ULPS before disabling the interface. This can be used to skip ULPS entry in cases where the panel doesn't care about ULPS state, for example when the panel will be reset, or when the display interface will be enabled again right after the disable. This will speed up the operation considerably in cases where entering ULPS would fail with timeout, and the panel driver isn't even interested in entering ULPS. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: DSI: add option to leave DSI lanes powered onTomi Valkeinen
The DSI pins are powered by VDDS_DSI. If VDDS_DSI is off, the DSI pins are floating even if they are pinmuxed to, say, safe mode and there's a pull down/up. This patch gives the panel drivers an option to leave the VDDS_DSI power enabled while the DSS itself is turned off. This can be used to keep the DSI lanes in a valid state while DSS is off, if the DSI pins are muxed for pull down (not done in this patch). There will be a slight power consumption increase (~100 uA?) when the VDDS_DSI is left on, but because this option is used when the panel is left on, the regulator consumption is negligible compared to panel power consumption. When the panel is fully turned off the VDDS_DSI is also turned off. As an added bonus this will give us faster start up time when starting up the DSS and the regulator is already enabled. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: use __exit for selected panel driversTomi Valkeinen
We can use __exit for the driver remove function in plain dss panels (ie. those that do not need i2c or spi). Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: Move nokia-dsi-panel.h to include/video/Tomi Valkeinen
arch/arm/plat-omap/include/plat/nokia-dsi-panel.h is an include for the OMAP DSS panel driver for Nokia's DSI displays. A more logical place for it is in include/video. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: Move display.h to include/video/Tomi Valkeinen
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS driver. A more logical place for it is in include/video. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6: (140 commits) MAINTAINERS: de-orphan fbdev. MAINTAINERS: Add file pattern for fb dt bindings. video: Move sm501fb devicetree binding documentation to a better place. fbcon: fix situation where fbcon gets deinitialised and can't reinit. video, sm501: add OF binding to support SM501 video, sm501: add edid and commandline support video, sm501: add I/O functions for use on powerpc video: Fix EDID macros H_SYNC_WIDTH and H_SYNC_OFFSET fbcon: Bugfix soft cursor detection in Tile Blitting video: add missing framebuffer_release in error path video: metronomefb: add __devexit_p around reference to metronomefb_remove video: hecubafb: add __devexit_p around reference to hecubafb_remove drivers:video:aty:radeon_base Fix typo occationally to occasionally atmel_lcdfb: add fb_blank function atmel_lcdfb: implement inverted contrast pwm video: s3c-fb: return proper error if clk_get fails uvesafb,vesafb: create WC or WB PAT-entries video: ffb: fix ffb_probe error path radeonfb: Let hwmon driver probe the "monid" I2C bus fbdev: sh_mobile_lcdc: checking NULL instead of IS_ERR() ...
2011-03-22backlight: add backlight typeMatthew Garrett
There may be multiple ways of controlling the backlight on a given machine. Allow drivers to expose the type of interface they are providing, making it possible for userspace to make appropriate policy decisions. Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: David Airlie <airlied@linux.ie> Cc: Alex Deucher <alexdeucher@gmail.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Len Brown <lenb@kernel.org> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-03-11OMAP: DSS2: Use request / release calls in Taal for DSI Virtual Channels.Archit Taneja
Taal driver used to take a hard coded Macro for Virtual Channel and the VC_ID. The Taal panel driver now requests for a Virtual channel through the omap_dsi_request_vc() call in taal_probe(). The channel number returned by the request_vc() call is used for sending command and data to the Panel. The DSI driver automatically configures the Virtual Channel's source to either Video Port or L4 Slave port based on what the panel driver is using it for. The driver uses omap_dsi_release_vc() to free the VC specified by the panel. taal_remove() or when a request_vc() call fails. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2010-11-16backlight: constify backlight_opsLionel Debroux
backlight_device_register has been expecting a const "ops" argument, and using it as such, since 9905a43b2d563e6f89e4c63c4278ada03f2ebb14. Let's make the remaining backlight_ops instances const. Inspired by hunks of the grsecurity patch, updated for newer kernels. Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-08-05OMAP: DSS2: Taal: Optimize enable_te, rotate, mirror when value unchangedTomi Valkeinen
Skip any further processing of taal_enable_te(), taal_rotate(), and taal_mirror() if value remains unchanged. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-05OMAP: DSS2: change manual update scaling setupTomi Valkeinen
Currently the update area on manual update displays is automatically enlargened to fully cover scaled overlays. This patch makes that optional, allowing the panel driver to choose if it's used or not. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: CABC workaround is Taal specificJani Nikula
Prepare for supporting panels other than Taal in this driver. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Add regulator configuration supportTomi Valkeinen
Add support for configuring regulators in the panel specific configuration data. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Print panel name in addition to revisionJani Nikula
The driver will support other panels in addition to Taal, print also the name. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Add panel specific configuration structureJani Nikula
Add a structure for panel specific configration to be able to support more than one panel in the future. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Configure ESD check in DSI panel dataJani Nikula
Make ESD check usage configurable in DSI panel data, as opposed to a define. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Use Nokia DSI panel dataTomi Valkeinen
Get board specific information from the Nokia DSI panel data structure instead of the DSS. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Add proper external TE supportJani Nikula
Add gpio irq based external TE support with timeout. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Change probe error handling labelsJani Nikula
Switch from numbered to named labels to make it easier to add new labels for error handling. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Change ESD work managementJani Nikula
Move ESD work queuing and cancelling out of taal_power_on/off() to avoid problems related to taal_esd_work() calling the power on/off functions. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Check taal_power_on() return value in taal_resume()Jani Nikula
Change state only if power on was succesful. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Change DSI bus locking to avoid deadlock in ESD workJani Nikula
Move dsi_bus_lock/unlock() out of taal_power_on/off() to avoid deadlock in taal_esd_work(). Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Ensure panel is enabled in enable_te() and run_test()Jani Nikula
Bail out from taal_enable_te() and taal_run_test() if panel is not enabled. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Improve taal_power_on() error handlingJani Nikula
Check return values and bail out on errors. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Remove ESD work cancel from driver probe error handlingJani Nikula
ESD work is never queued in probe, no need to cancel it on probe error. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Fix request_irq() error handlingJani Nikula
Separate gpio_request() and request_irq() error handling. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Remove platform enable/disableJani Nikula
After the addition of proper hardware reset, taal_hw_reset(), there's no need for an additional platform enable/disable. Remove them. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Add locks to protect taal data accessJani Nikula
Avoid potential race conditions in sysfs access to taal data. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: Add panel hardware resetJani Nikula
Issue a proper reset pulse on the reset line instead of just doing power on/off. Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-08-03OMAP: DSS2: Taal: add locks to taal_bl_update_statusTomi Valkeinen
taal_bl_update_status was missing locks to protect taal_data. This caused a kernel crash randomly, as the code attempted to set the brightness while the OMAP's DSI block was actually disabled. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-05-18OMAP: DSS2: Taal: Fix DSI bus locking problemVille Syrjälä
If omapdss_dsi_display_enable() failed the DSI bus was left locked. Also if the operation failed later omapdss_dsi_display_disable() would get called without holding the bus lock. Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-05-18OMAP: DSS2: Taal: add mutex to protect panel dataTomi Valkeinen
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-03-30include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo
implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-16backlight: Allow properties to be passed at registrationMatthew Garrett
Values such as max_brightness should be set before backlights are registered, but the current API doesn't allow that. Add a parameter to backlight_device_register and update drivers to ensure that they set this correctly. Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
2010-03-02OMAP: DSS2: Taal: Fix TE when resumingTomi Valkeinen
TE was not initialized properly on power on, which broke TE when resuming from suspend. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-03-01OMAP: DSS2: Taal: Fix ESD checkTomi Valkeinen
Using taal_enable_te() when DSI bus was locked caused a deadlock. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-02-24OMAP: DSS2: move timing functionsTomi Valkeinen
Move check/set/get_timings() from omap_dss_device to omap_dss_driver. This is part of a larger patch-set, which moves the control from omapdss driver to the display driver. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-02-24OMAP: DSS2: move enable/disable/suspend/resumeTomi Valkeinen
Move enable/disable/suspend/resume from omap_dss_device to omap_dss_driver. This is part of a larger patch-set, which moves the control from omapdss driver to the display driver. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2010-02-24OMAP: DSS2: move update() and sync()Tomi Valkeinen
Move update() and sync() from omap_dss_device to omap_dss_driver. Also, update was hardcoded to use virtual channel 0. This patch adds a parameter that specifies the VC. This is part of a larger patch-set, which moves the control from omapdss driver to the display driver. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-11-12 22:00:33 +0000