summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2014-07-07tlan: Restart autonegotiation on link lossOndrej Zary
When link is lost on a card which uses internal PHY for 10 Mbit speeds, restart autonegotiation to allow switching between 10 and 100 Mbps speeds. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07tlan: Fix MAC address byte order on OC-2325/OC-2326Ondrej Zary
Olicom OC-2325 and OC-2326 cards have the MAC address byte-swapped in EEPROM. Byte-swap the MAC address if it's located at offset 0xF8. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07tlan: Add ethtool supportOndrej Zary
Add basic ethtool support to tlan driver: - driver info - link detect (this allows NetworkManager to detect carrier) - EEPROM read Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07tlan: Enable link monitoringOndrej Zary
Enable old link monitoring code and modify it: - control LINK LED - use separate timer so it does not interfere with ACT LED Tested with Olicom OC-2326. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07tlan: Enable activity LED on Olicom OC-2325 and OC-2326Ondrej Zary
Olicom OC-2325 and OC-2326 ethernet cards have an activity LED but it does not work with tlan driver as it's not enabled. Enable it. Tested with OC-2326. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-07ptp: Classify ptp over ip over vlan packetsStefan Sørensen
This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp classes are changed to orthogonal bitfields representing version, transport and vlan values to simplify matching. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-02be2net: re-enable vlan filtering mode asapKalesh AP
While adding vlans, when the HW limit of vlan filters is reached, the driver enables vlan promiscuous mode. Similarily, while removing vlans, the driver must re-enable HW filtering as soon as the number of vlan filters is within the HW limit. Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-02be2net: create optimal number of queues on SR-IOV configVasundhara Volam
If SR-IOV is enabled in the adapter, the FW distributes queue resources evenly across the PF and it's VFs. If the user is not interested in enabling VFs, the queues set aside for VFs are wasted. This patch adds support for the PF driver to re-configure the resource distribution in FW based on the number of VFs enabled by the user. This also allows for supporting RSS queues on VFs, when less number of VFs are enabled per PF. When maximum number of VFs are enabled, each VF typically gets only one RXQ. Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-02be2net: read VF's capabilities from GET_PROFILE_CONFIG cmdVasundhara Volam
The PF driver must query the FW for VF's interface capabilities to know if the VF is RSS capable or not. This patch is in preparation for enabling RSS on VFs on Skyhawk-R. Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-02be2net: remove be_cmd_get_profile_config_mbox/mccq() variantsVasundhara Volam
Fix be_cmd_get_profile_cmd() to use be_cmd_notify_wait() routine, which uses MBOX if MCCQ has not been created. Doing this reduces code duplication; we don't need the _mbox/_mccq() variants anymore. Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-02drivers/net/hyperv/netvsc.c: remove unnecessary null test before kfreeFabian Frederick
Fix checkpatch warning: WARNING: kfree(NULL) is safe this check is probably not required Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: netdev@vger.kernel.org Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-02sh_eth: remove checks around dev_kfree_skb() callsSergei Shtylyov
Since consume_skb() (and hence dev_kfree_skb() macro) checks the passed pointer for NULL, there's no need to check for NULL before invoking dev_kfree_skb(). Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-02qlcnic: Update version to 5.3.61Harish Patil
Signed-off-by: Harish Patil <harish.patil@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-02qlcnic: Enhance Tx timeout debug data collection.Harish Patil
- Collect a firmware dump on first Tx timeout if netif_msg_tx_err() is set - Log Receive and Status ring info on Tx timeout, in addition to Tx ring info - Log additional Tx ring info if netif_msg_tx_err() is set Signed-off-by: Harish Patil <harish.patil@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-02drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: remove unnecessary null ↵Fabian Frederick
test before debugfs_remove_recursive Fix checkpatch warning: "WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required" Cc: Hariprasad S <hariprasad@chelsio.com> Cc: netdev@vger.kernel.org Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2014-07-01 This series contains updates to i40e, i40evf, igb and ixgbe. Shannon adds the Base Address High and Low to the admin queue structure to simplify the logic in the configuration routines. Also adds code to clear all queues and interrupts to help clean up after a PXE or other early boot activity. Kevin fixes mask assignment value since -1 cannot be used for unsigned integer types. Mitch fixes an issue where in some circumstances the reply from the PF would come back before we were able to properly modify the admin queue pending and required flags. This would mess up the flags and put the driver in an indeterminate state, so fix this by simply setting the flags before sending the request to the admin queue. Also changes the branding string for i40evf to reduce confusion and to match up with our other marketing materials. Kamil adds a new variable defining admin send queue (ASQ) command write back timeout to allow for dynamic modification of this timeout. Anjali fix a bug in the flow director filter replay logic, so that we call a replay after a sideband reset correctly. Jesse adds code to initialize all members of the context descriptor to prevent possible stale data. Christopher fixes i40e to prevent writing to reserved bits, since the queue index is only 0-127. Jacob removes the unneeded header export.h from the i40e PTP code. Fixes ixgbe PTP code where the PPS signal was not correct, as it generates a one half HZ clock signal, it only generates one level change per second. To generate a full clock, we need two level changes per second. Todd provides a fix for igb to bring up link when the PHY has powered up, which was reported by Jeff Westfahl. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01bonding: allow to add vlans on top of empty bondJiri Pirko
This limitation maybe had some reason in the past, but now there is not one -> removing this. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01cxgb4vf: Adds device ID for few more Chelsio T4 AdaptersHariprasad Shenai
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01cxgb4: Adds device ID for few more Chelsio T4 AdaptersHariprasad Shenai
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01cxgb4: Replaced the backdoor mechanism to access the HW memory with PCIe ↵Hariprasad Shenai
Window method Rip out a bunch of redundant PCI-E Memory Window Read/Write routines, collapse the more general purpose routines into a single routine thereby eliminating the need for a large stack frame (and extra data copying) in the outer routine, change everything to use the improved routine t4_memory_rw. Based on origninal work by Casey Leedom <leedom@chelsio.com> and Steve Wise <swise@opengridcomputing.com> Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01cxgb4: Use FW interface to get BAR0 valueHariprasad Shenai
Use the firmware interface to get the BAR0 value since we really don't want to use the PCI-E Configuration Space Backdoor access which is owned by the firmware. Set up PCI-E Memory Window registers using the true values programmed into BAR registers. When the PF4 "Master Function" is exported to a Virtual Machine, the values returned by pci_resource_start() will be for the synthetic PCI-E Configuration Space and not the real addresses. But we need to program the PCI-E Memory Window address decoders with the real addresses that we're going to be using in order to have accesses through the Memory Windows work. Based on origninal work by Casey Leedom <leedom@chelsio.com> Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01rdma/cxgb4: Fixes cxgb4 probe failure in VM when PF is exposed through PCI ↵Hariprasad Shenai
Passthrough Change logic which determines our Physical Function at PCI Probe time. Now we read the PL_WHOAMI register and get the Physical Function. Pass Physical Function to Upper Layer Drivers in lld_info structure in the new field "pf" added to lld_info. This is useful for the cases where the PF, say PF4, is attached to a Virtual Machine via some form of "PCI Pass Through" technology and the PCI Function shows up as PF0 in the VM. Based on original work by Casey Leedom <leedom@chelsio.com> Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01ptp: Allow reassigning calibration pin functionStefan Sørensen
The ptp pin function programming does not allow calibration pin to change function. This is problematic on hardware that uses the default calibration pin for other purposes. Removing this limitation does not impact calibration if userspace does not reprogram the calibration pin. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01dp83640: Get calibration pin with ptp_find_pinStefan Sørensen
For consistency, use the ptp_find_pin function to get the calibration pin, not gpio_tab. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01dp83640: Verify calibration pin assignmentStefan Sørensen
This constraints the pin assignment to not allow the calibration function to be reassigned and only allow reassigning the calibratin pin if only one phy is connected. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01dp83640: Increase supported perout pins to 7Stefan Sørensen
This patch increases the number of supported periodic output pins from 1 to 7. The last pin is reserved for sync. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01dp83640: Program pulsewidth2 values of perout triggers 0 and 1Stefan Sørensen
Periodic output triggers 0 and 1 of the dp83640 has a programmable duty-cycle which is controlled by the Pulsewidth2 field of the trigger data register. This field is not documented in the datasheet, but it is described in the "PHYTER Software Development Guide" section 3.1.4.1. Failing to set the field can result in unstable/no trigger output. Add programming of the Pulsewidth2 field, setting it to the same value as the Pulsewidth field for a 50% duty cycle. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01bnx2x: Fail probe of VFs using an old incompatible driverYuval Mintz
There are linux distributions where the inbox bnx2x driver contains SRIOV support but doesn't contain the changes introduced in b9871bcf "bnx2x: VF RSS support - PF side". A VF in a VM running that distribution over a new hypervisor will access incorrect addresses when trying to transmit packets, causing an attention in the hypervisor and making that VF inactive until FLRed. The driver in the VM has to ne upgraded [no real way to overcome this], but due to the HW attention currently arising upgrading the driver in the VM would not suffice [since the VF needs also be FLRed if the previous driver was already loaded]. This patch causes the PF to fail the acquire message from a VF running an old problematic driver; The VF will then gracefully fail it's probe preventing the HW attention [and allow clean upgrade of driver in VM]. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01bnx2x: enlarge minimal alignemnt of data offsetDmitry Kravkov
This improves the performance of driver on machine with L1_CACHE_SHIFT of at most 32 bytes [HW was planned for 64-byte aligned fastpath data]. Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01bnx2x: VF can report link speedDmitry Kravkov
Until now VFs were oblvious to the actual configured link parameters. This patch does 2 things: 1. It enables a PF to inform its VF using the bulletin board of the link configured, and allows the VF to present that information. 2. It adds support of `ndo_set_vf_link_state', allowing the hypervisor to set the VF link state. Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-01ixgbe: change PTP NSECS_PER_SEC to IXGBE_PTP_PPS_HALF_SECONDJacob Keller
The PPS signal is not correct, as it generates a one half HZ clock signal, as it only generates one level change per second. To generate a full clock, we need two level changes per second. Also, change the name of the #define, in order to prevent confusion between it and NSEC_PER_SEC which is not guaranteed to be a 64bit value. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-07-01igb: bring link up when PHY is powered upTodd Fujinaka
Call igb_setup_link() when the PHY is powered up. Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com> Reported-by: Jeff Westfahl <jeff.westfahl@ni.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-07-01i40e/i40evf: Bump i40e to 0.4.19 and i40evf to 0.9.38Catherine Sullivan
Bump versions. Change-ID: Id5082d7c3995fbddd22b3e303d804c86fcd240a3 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-07-01i40evf: change branding stringMitch Williams
Add a slash to the branding string to reduce confusion and match up with our other marketing materials. Change-ID: I8229e8c3e43083b7a29c859a250f8d2d4dc46b9e Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-07-01i40e: remove linux/export.h header from i40e_ptp.cJacob Keller
We don't need the export.h header so we can just go ahead and remove it. Change-ID: I9057396b141ee449d8299409081358b9270a7c4d Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-07-01i40e: limit GLLAN_TXPRE_QDIS to QINDX 0-127Christopher Pau
Prevent writing to reserved bits, queue index is 0-127 Change-ID: Ic923e1c92012a265983414acd8f547c4bdac2e34 Signed-off-by: Christopher Pau <christopher.pau@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-07-01i40e/i40evf: initialize context descriptorJesse Brandeburg
Driver needs to initialize all members of context descriptor. Stale data is possible otherwise. Change-ID: Idc6b53af45583509da42d5ec0824cbaf78aee64f Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-07-01i40e: FD filter replay logic bug fixAnjali Singhai Jain
With the auto_disable flags added there was a bug that was causing the replay logic to not work correctly. This patch fixes the issue so that we call a replay after a sideband reset correctly. Change-ID: I005fe1ac361188ee5b19517a83c922038cba1b00 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-30i40e/i40evf: add ASQ write back timeout variable to AQ structureKamil Krawczyk
Add new variable defining ASQ command write back timeout to allow for dynamic modification of this timeout. Initialize it on AQ initialize routine with default value, vary it on device ID. Change-ID: I5c9908f9d7c5455634353b694a986d6f146d1b9d Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-30i40evf: set flags before sending messageMitch Williams
In some circumstances, the firmware could beat us to the punch, and the reply from the PF would come back before we were able to properly modify the aq_pending and aq_required flags. This would mess up the flags and put the driver in an indeterminate state, much like Schrödinger's cat. However, unlike the cat, the driver is definitely dead. To fix this, simply set the flags before sending the request to the AQ. This way, it won't matter if the interrupt comes back too soon. Change-ID: I9784655e475675ebcb3140cc7f36f4a96aaadce5 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-30i40e: Correct mask assignment valueKevin Scott
Make mask value of all 1s. Value of -1 can't be used for u32 type. Change-ID: I49d58b77639939fe7447a229dbf1f4a1bf7419ce Signed-off-by: Kevin Scott <kevin.c.scott@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-30i40e: clear all queues and interruptsShannon Nelson
Per a recent HW designer comment, this code is for ripping through the queues and interrupts to fully disable them on driver init, specifically to help clean up after a PXE or other early boot activity. Change-ID: I32ed452021a1c2b06dace1969976f882a37b9741 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-30i40e/i40evf: clear aq bah-bal on shutdownShannon Nelson
Clear the AQ BAH and BAL registers on a clean shutdown to help make sure all is tidy when the driver is done. Change-ID: I393e92680247daa52a8e00bab183213672d73578 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-30i40e/i40evf: Add base address registers to aq structShannon Nelson
Add the Base Address High and Low to the admin queue struct to simplify another bit of "which context" logic in the config routines. Change-ID: Iae195a7da3baffc1a9d522119e1e2b427068ad07 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-27Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2014-06-26 This series contains updates to i40e and i40evf. Kamil provides a cleanup patch to i40e where we do not need to acquire the NVM for shadow RAM checksum calculation, since we only read the shadow RAM through SRCTL register. Paul provides a fix for handling HMC for big endian architectures for i40e and i40evf. Mitch provides four cleanup and fixes for i40evf. Fix an issue where if the VF driver fails to complete early init, then rmmod can cause a softlock when the driver tries to stop a watchdog timer that never got initialized. So add a check to see if the timer is actually initialized before stopping it. Make the function i40evf_send_api_ver() return more useful information, instead of just returning -EIO by propagating firmware errors back to the caller and log a message if the PF sends an invalid reply. Fix up a log message that was missing a word, which makes the log message more readable. Fix an initialization failure if many VFs are instantiated at the same time and the VF module is autoloaded by simply resending firmware request if there is no response the first time. Jacob does a rename of the function i40e_ptp_enable() to i40e_ptp_feature_enable(), like he did for ixgbe, to reduce possible confusion and ambugity in the purpose of the function. Does follow on PTP work on i40e, like he did for ixgbe, by breaking the PTP hardware control from the ioctl command for timestamping mode. By doing this, we can maintain state about the 1588 timestamping mode and properly re-enable to the last known mode during a re-initialization of 1588 bits. Anjali cleans up the i40e driver where TCP-IPv4 filters were being added twice, which seems to be left over from when we had to add two PTYPEs for one filter. Fixes the flow director sideband logic to detect when there is a full flow director table. Also fixes the programming of FDIR where a couple of fields in the descriptor setup that were not being programmed, which left the opportunity for stale data to be pushed as part of the descriptor next time it was used. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26amd-xgbe: Resolve checkpatch warning about sscanf usageLendacky, Thomas
Checkpatch issued a warning preferring to use kstrto<type> when using a single variable sscanf. Change the sscanf invocation to a kstrtouint call. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26amd-xgbe: Change destination address filtering supportLendacky, Thomas
Currently the driver makes use of the additional mac address registers in the hardware to provide perfect filtering. The hardware can also have a set of hash table registers that can be used for imperfect filtering. By using imperfect filtering the additional mac address registers can be used for layer 2 filtering support. Use the hash table registers if the device has them. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26amd-xgbe: Add support for VLAN filteringLendacky, Thomas
This patch adds support for (imperfect) filtering of VLAN tag ids using a 16-bit filter hash table. When VLANs are added, a 4-bit hash is calculated with the result indicating the bit in the hash table to set. This table is used by the hardware to drop packets with a VLAN id that does not hash to a set bit in the table. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26amd-xgbe: VLAN Rx tag stripping fixLendacky, Thomas
When receiving a VLAN packet check to be sure that VLAN RX CTAG stripping is enabled before indicating that the tag has been stripped in the packet information data structure. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-26amd-xgbe: VLAN Tx tag insertion fixLendacky, Thomas
The MAC_VLAN_Incl register (0x0060) must be set to indicate that the VLAN tag to be inserted comes from a Tx context descriptor and not the MAC_VLAN_Incl register. Also, even though it is the default, explicitly set the type of tag to be inserted as a CTAG. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.0.4) at 2025-02-07 12:58:22 +0000