| Age | Commit message (Collapse) | Author |
|---|
|
Change to using max P-state instead of max turbo P-state. This
change resolves two issues.
On a quiet system intel_pstate can fail to respond to a load change.
On CPU SKUs that have a limited number of P-states and no turbo range
intel_pstate fails to select the highest available P-state.
This change is suitable for stable v3.9+
References: https://bugzilla.kernel.org/show_bug.cgi?id=59481
Reported-and-tested-by: Arjan van de Ven <arjan@linux.intel.com>
Reported-and-tested-by: dsmythies@telus.net
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI video support fixes from Rafael Wysocki:
"I'm sending a separate pull request for this as it may be somewhat
controversial. The breakage addressed here is not really new and the
fixes may not satisfy all users of the affected systems, but we've had
so much back and forth dance in this area over the last several weeks
that I think it's time to actually make some progress.
The source of the problem is that about a year ago we started to tell
BIOSes that we're compatible with Windows 8, which we really need to
do, because some systems shipping with Windows 8 are tested with it
and nothing else, so if we tell their BIOSes that we aren't compatible
with Windows 8, we expose our users to untested BIOS/AML code paths.
However, as it turns out, some Windows 8-specific AML code paths are
not tested either, because Windows 8 actually doesn't use the ACPI
methods containing them, so if we declare Windows 8 compatibility and
attempt to use those ACPI methods, things break. That occurs mostly
in the backlight support area where in particular the _BCM and _BQC
methods are plain unusable on some systems if the OS declares Windows
8 compatibility.
[ The additional twist is that they actually become usable if the OS
says it is not compatible with Windows 8, but that may cause
problems to show up elsewhere ]
Investigation carried out by Matthew Garrett indicates that what
Windows 8 does about backlight is to leave backlight control up to
individual graphics drivers. At least there's evidence that it does
that if the Intel graphics driver is used, so we've decided to follow
Windows 8 in that respect and allow i915 to control backlight (Daniel
likes that part).
The first commit from Aaron Lu makes ACPICA export the variable from
which we can infer whether or not the BIOS believes that we are
compatible with Windows 8.
The second commit from Matthew Garrett prepares the ACPI video driver
by making it initialize the ACPI backlight even if it is not going to
be used afterward (that is needed for backlight control to work on
Thinkpads).
The third commit implements the actual workaround making i915 take
over backlight control if the firmware thinks it's dealing with
Windows 8 and is based on the work of multiple developers, including
Matthew Garrett, Chun-Yi Lee, Seth Forshee, and Aaron Lu.
The final commit from Aaron Lu makes us follow Windows 8 by informing
the firmware through the _DOS method that it should not carry out
automatic brightness changes, so that brightness can be controlled by
GUI.
Hopefully, this approach will allow us to avoid using blacklists of
systems that should not declare Windows 8 compatibility just to avoid
backlight control problems in the future.
- Change from Aaron Lu makes ACPICA export a variable which can be
used by driver code to determine whether or not the BIOS believes
that we are compatible with Windows 8.
- Change from Matthew Garrett makes the ACPI video driver initialize
the ACPI backlight even if it is not going to be used afterward
(that is needed for backlight control to work on Thinkpads).
- Fix from Rafael J Wysocki implements Windows 8 backlight support
workaround making i915 take over bakclight control if the firmware
thinks it's dealing with Windows 8. Based on the work of multiple
developers including Matthew Garrett, Chun-Yi Lee, Seth Forshee,
and Aaron Lu.
- Fix from Aaron Lu makes the kernel follow Windows 8 by informing
the firmware through the _DOS method that it should not carry out
automatic brightness changes, so that brightness can be controlled
by GUI"
* tag 'acpi-video-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: no automatic brightness changes by win8-compatible firmware
ACPI / video / i915: No ACPI backlight if firmware expects Windows 8
ACPI / video: Always call acpi_video_init_brightness() on init
ACPICA: expose OSI version
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg KH:
"Here are a few iio driver fixes for 3.11-rc2. They are still spread
across drivers/iio and drivers/staging/iio so they are coming in
through this tree.
I've also removed the drivers/staging/csr/ driver as the developers
who originally sent it to me have moved on to other companies, and CSR
still will not send us the specs for the device, making the driver
pretty much obsolete and impossible to fix up. Deleting it now
prevents people from sending in lots of tiny codingsyle fixes that
will never go anywhere.
It also helps to offset the large lustre filesystem merge that
happened in 3.11-rc1 in the overall 3.11.0 diffstat. :)"
* tag 'staging-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: csr: remove driver
iio: lps331ap: Fix wrong in_pressure_scale output value
iio staging: fix lis3l02dq, read error handling
staging:iio:ad7291: add missing .driver_module to struct iio_info
iio: ti_am335x_adc: add missing .driver_module to struct iio_info
iio: mxs-lradc: Remove useless check in read_raw
iio: mxs-lradc: Fix misuse of iio->trig
iio: inkern: fix iio_convert_raw_to_processed_unlocked
iio: Fix iio_channel_has_info
iio:trigger: device_unregister->device_del to avoid double free
iio: dac: ad7303: fix error return code in ad7303_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"An update for the BFP jit to the latest and greatest, two patches to
get kdump working again, the random-abort ptrace extention for
transactional execution, the z90crypt module alias for ap and a tiny
cleanup"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/zcrypt: Alias for new zcrypt device driver base module
s390/kdump: Allow copy_oldmem_page() copy to virtual memory
s390/kdump: Disable mmap for s390
s390/bpf,jit: add pkt_type support
s390/bpf,jit: address randomize and write protect jit code
s390/bpf,jit: use generic jit dumper
s390/bpf,jit: call module_free() from any context
s390/qdio: remove unused variable
s390/ptrace: PTRACE_TE_ABORT_RAND
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes collected over the last week, most importnatly two
cpufreq reverts fixing regressions introduced in 3.10, an autoseelp
fix preventing systems using it from crashing during shutdown and two
ACPI scan fixes related to hotplug.
Specifics:
- Two cpufreq commits from the 3.10 cycle introduced regressions.
The first of them was buggy (it did way much more than it needed to
do) and the second one attempted to fix an issue introduced by the
first one. Fixes from Srivatsa S Bhat revert both.
- If autosleep triggers during system shutdown and the shutdown
callbacks of some device drivers have been called already, it may
crash the system. Fix from Liu Shuo prevents that from happening
by making try_to_suspend() check system_state.
- The ACPI memory hotplug driver doesn't clear its driver_data on
errors which may cause a NULL poiter dereference to happen later.
Fix from Toshi Kani.
- The ACPI namespace scanning code should not try to attach scan
handlers to device objects that have them already, which may
confuse things quite a bit, and it should rescan the whole
namespace branch starting at the given node after receiving a bus
check notify event even if the device at that particular node has
been discovered already. Fixes from Rafael J Wysocki.
- New ACPI video blacklist entry for a system whose initial backlight
setting from the BIOS doesn't make sense. From Lan Tianyu.
- Garbage string output avoindance for ACPI PNP from Liu Shuo.
- Two Kconfig fixes for issues introduced recently in the s3c24xx
cpufreq driver (when moving the driver to drivers/cpufreq) from
Paul Bolle.
- Trivial comment fix in pm_wakeup.h from Chanwoo Choi"
* tag 'pm+acpi-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: ignore BIOS initial backlight value for Fujitsu E753
PNP / ACPI: avoid garbage in resource name
cpufreq: Revert commit 2f7021a8 to fix CPU hotplug regression
cpufreq: s3c24xx: fix "depends on ARM_S3C24XX" in Kconfig
cpufreq: s3c24xx: rename CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
PM / Sleep: Fix comment typo in pm_wakeup.h
PM / Sleep: avoid 'autosleep' in shutdown progress
cpufreq: Revert commit a66b2e to fix suspend/resume regression
ACPI / memhotplug: Fix a stale pointer in error path
ACPI / scan: Always call acpi_bus_scan() for bus check notifications
ACPI / scan: Do not try to attach scan handlers to devices having them
|
|
The zcrypt device driver has been split into base/bus module, api-module,
card modules and message type modules. The base module has been renamed
from z90crypt to ap.
A module alias (with the well-known z90crypt identifier) will be introduced
that enable users to use their existing way to load the zcrypt device driver.
Signed-off-by: Ingo Tuchscherer <ingo.tuchscherer@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Pull networking fixes from David Miller:
"A couple interesting SKB fragment handling fixes, plus the usual small
bits here and there:
1) Fix 64-bit divide build failure on 32-bit platforms in mlx5, from
Tim Gardner.
2) Get rid of a stupid reimplementation on "%*phC" in our sysfs MAC
address printing helper.
3) Fix NETIF_F_SG capability advertisement in hyperv driver, if the
device can't do checksumming offloads then it shouldn't say it can
do SG either. From Haiyang Zhang.
4) bgmac needs to depend on PHYLIB, from Hauke Mehrtens.
5) Don't leak DMA mappings on mapping failures, from Neil Horman.
6) We need to reset the transport header of SKBs in ipv4 before we
attempt to perform early socket demux, just like ipv6 does. From
Eric Dumazet.
7) Add missing locking on vxlan device removal, from Stephen
Hemminger.
8) xen-netfront has to make two passes over an SKB to prepare it for
transfer. One pass calculates the number of slots needed, the
second massages the SKB and fills the slots. Unfortunately, the
first pass doesn't calculate the number of slots properly so we
can end up trying to build a MAX_SKB_FRAGS + 1 SKB which doesn't
work out so well. Fix from Jan Beulich with help and discussion
with several others.
9) Fix a similar problem in tun and macvtap, which have to split up
scatter-gather elements at PAGE_SIZE boundaries. Don't do
zerocopy if it would result in a > MAX_SKB_FRAGS skb. Fixes from
Jason Wang.
10) On receive, once we've decoded the VLAN state completely, clear
skb->vlan_tci. Otherwise demuxed tunnels underneath can trigger
the VLAN code again, corrupting the packet. Fix from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
vlan: fix a race in egress prio management
vlan: mask vlan prio bits
macvtap: do not zerocopy if iov needs more pages than MAX_SKB_FRAGS
tuntap: do not zerocopy if iov needs more pages than MAX_SKB_FRAGS
pkt_sched: sch_qfq: remove a source of high packet delay/jitter
xen-netfront: pull on receive skb may need to happen earlier
vxlan: add necessary locking on device removal
hyperv: Fix the NETIF_F_SG flag setting in netvsc
net: Fix sysfs_format_mac() code duplication.
be2net: Fix to avoid hardware workaround when not needed
macvtap: do not assume 802.1Q when send vlan packets
macvtap: fix the missing ret value of TUNSETQUEUE
ipv4: set transport header earlier
mlx5 core: Fix __udivdi3 when compiling for 32 bit arches
bgmac: add dependency to phylib
net/irda: fixed style issues in irlan_eth
ethtool: fixed trailing statements in ethtool
ndisc: bool initializations should use true and false
atl1e: unmap partially mapped skb on dma error and free skb
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Trying again to get the fixes queue, including the fixed IDT alignment
patch.
The UEFI patch is by far the biggest issue at hand: it is currently
causing quite a few machines to boot. Which is sad, because the only
reason they would is because their BIOSes touch memory that has
already been freed. The other major issue is that we finally have
tracked down the root cause of a significant number of machines
failing to suspend/resume"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Make sure IDT is page aligned
x86, suspend: Handle CPUs which fail to #GP on RDMSR
x86/platform/ce4100: Add header file for reboot type
Revert "UEFI: Don't pass boot services regions to SetVirtualAddressMap()"
efivars: check for EFI_RUNTIME_SERVICES
|
|
Pull md bug fixes from NeilBrown:
"Sorry boss, back at work now boss. Here's them nice shiny patches ya
wanted. All nicely tagged and justified for -stable and everyfing:
Three bug fixes for md in 3.10
3.10 wasn't a good release for md. The bio changes left a couple of
bugs, and an md "fix" created another one.
These three patches appear to fix the issues and have been tagged for
-stable"
* tag 'md-3.11-fixes' of git://neil.brown.name/md:
md/raid1: fix bio handling problems in process_checks()
md: Remove recent change which allows devices to skip recovery.
md/raid10: fix two problems with RAID10 resync.
|
|
Pull drm fixes from Dave Airlie:
"You'll be terribly disappointed in this, I'm not trying to sneak any
features in or anything, its mostly radeon and intel fixes, a couple
of ARM driver fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (34 commits)
drm/radeon/dpm: add debugfs support for RS780/RS880 (v3)
drm/radeon/dpm/atom: fix broken gcc harder
drm/radeon/dpm/atom: restructure logic to work around a compiler bug
drm/radeon/dpm: fix atom vram table parsing
drm/radeon: fix an endian bug in atom table parsing
drm/radeon: add a module parameter to disable aspm
drm/rcar-du: Use the GEM PRIME helpers
drm/shmobile: Use the GEM PRIME helpers
uvesafb: Really allow mtrr being 0, as documented and warn()ed
radeon kms: do not flush uninitialized hotplug work
drm/radeon/dpm/sumo: handle boost states properly when forcing a perf level
drm/radeon: align VM PTBs (Page Table Blocks) to 32K
drm/radeon: allow selection of alignment in the sub-allocator
drm/radeon: never unpin UVD bo v3
drm/radeon: fix UVD fence emit
drm/radeon: add fault decode function for CIK
drm/radeon: add fault decode function for SI (v2)
drm/radeon: add fault decode function for cayman/TN (v2)
drm/radeon: use radeon device for request firmware
drm/radeon: add missing ttm_eu_backoff_reservation to radeon_bo_list_validate
...
|
|
We try to linearize part of the skb when the number of iov is greater than
MAX_SKB_FRAGS. This is not enough since each single vector may occupy more than
one pages, so zerocopy_sg_fromiovec() may still fail and may break the guest
network.
Solve this problem by calculate the pages needed for iov before trying to do
zerocopy and switch to use copy instead of zerocopy if it needs more than
MAX_SKB_FRAGS.
This is done through introducing a new helper to count the pages for iov, and
call uarg->callback() manually when switching from zerocopy to copy to notify
vhost.
We can do further optimization on top.
This bug were introduced from b92946e2919134ebe2a4083e4302236295ea2a73
(macvtap: zerocopy: validate vectors before building skb).
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We try to linearize part of the skb when the number of iov is greater than
MAX_SKB_FRAGS. This is not enough since each single vector may occupy more than
one pages, so zerocopy_sg_fromiovec() may still fail and may break the guest
network.
Solve this problem by calculate the pages needed for iov before trying to do
zerocopy and switch to use copy instead of zerocopy if it needs more than
MAX_SKB_FRAGS.
This is done through introducing a new helper to count the pages for iov, and
call uarg->callback() manually when switching from zerocopy to copy to notify
vhost.
We can do further optimization on top.
The bug were introduced from commit 0690899b4d4501b3505be069b9a687e68ccbe15b
(tun: experimental zero copy tx support)
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here are some driver core patches for 3.11-rc2. They aren't really
bugfixes, but a bunch of new helper macros for drivers to properly
create attribute groups, which drivers and subsystems need to fix up a
ton of race issues with incorrectly creating sysfs files (binary and
normal) after userspace has been told that the device is present.
Also here is the ability to create binary files as attribute groups,
to solve that race condition, which was impossible to do before this,
so that's my fault the drivers were broken.
The majority of the .c changes is indenting and moving code around a
bit. It affects no existing code, but allows the large backlog of 70+
patches that I already have created to start flowing into the
different subtrees, instead of having to live in my driver-core tree,
causing merge nightmares in linux-next for the next few months.
These were finalized too late for the -rc1 merge window, which is why
they were didn't make that pull request, testing and review from
others didn't happen until a few weeks ago, and then there's the whole
distraction of the past few days, which prevented these from getting
to you sooner, sorry about that.
Oh, and there's a bugfix for the documentation build warning in here
as well. All of these have been in linux-next this week, with no
reported problems"
* tag 'driver-core-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: fix new kernel-doc warning in base/platform.c
sysfs: use file mode defines from stat.h
sysfs: add more helper macro's for (bin_)attribute(_groups)
driver core: add default groups to struct class
driver core: Introduce device_create_groups
sysfs: prevent warning when only using binary attributes
sysfs: add support for binary attributes in groups
driver core: device.h: add RW and RO attribute macros
sysfs.h: add BIN_ATTR macro
sysfs.h: add ATTRIBUTE_GROUPS() macro
sysfs.h: add __ATTR_RW() macro
|
|
* pm-fixes:
cpufreq: Revert commit 2f7021a8 to fix CPU hotplug regression
cpufreq: s3c24xx: fix "depends on ARM_S3C24XX" in Kconfig
cpufreq: s3c24xx: rename CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
PM / Sleep: Fix comment typo in pm_wakeup.h
PM / Sleep: avoid 'autosleep' in shutdown progress
cpufreq: Revert commit a66b2e to fix suspend/resume regression
|
|
The BIOS of FUjitsu E753 reports an incorrect initial backlight value
for WIN8 compatible OS, causing backlight to be dark during startup.
This change causes the incorrect initial value from BIOS to be ignored.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60161
Reported-and-tested-by: Jan Hinnerk Stosch <janhinnerk.stosch@gmail.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Single patch to staticize a local variable"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (abx500) Staticize abx500_temp_attributes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull phase two of __cpuinit removal from Paul Gortmaker:
"With the __cpuinit infrastructure removed earlier, this group of
commits only removes the function/data tagging that was done with the
various (now no-op) __cpuinit related prefixes.
Now that the dust has settled with yesterday's v3.11-rc1, there
hopefully shouldn't be any new users leaking back in tree, but I think
we can leave the harmless no-op stubs there for a release as a
courtesy to those who still have out of tree stuff and weren't paying
attention.
Although the commits are against the recent tag to allow for minor
context refreshes for things like yesterday's v3.11-rc1~ slab content,
the patches have been largely unchanged for weeks, aside from such
trivial updates.
For detail junkies, the largely boring and mostly irrelevant history
of the patches can be viewed at:
http://git.kernel.org/cgit/linux/kernel/git/paulg/cpuinit-delete.git
If nothing else, I guess it does at least demonstrate the level of
involvement required to shepherd such a treewide change to completion.
This is the same repository of patches that has been applied to the
end of the daily linux-next branches for the past several weeks"
* 'cpuinit_phase2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (28 commits)
block: delete __cpuinit usage from all block files
drivers: delete __cpuinit usage from all remaining drivers files
kernel: delete __cpuinit usage from all core kernel files
rcu: delete __cpuinit usage from all rcu files
net: delete __cpuinit usage from all net files
acpi: delete __cpuinit usage from all acpi files
hwmon: delete __cpuinit usage from all hwmon files
cpufreq: delete __cpuinit usage from all cpufreq files
clocksource+irqchip: delete __cpuinit usage from all related files
x86: delete __cpuinit usage from all x86 files
score: delete __cpuinit usage from all score files
xtensa: delete __cpuinit usage from all xtensa files
openrisc: delete __cpuinit usage from all openrisc files
m32r: delete __cpuinit usage from all m32r files
hexagon: delete __cpuinit usage from all hexagon files
frv: delete __cpuinit usage from all frv files
cris: delete __cpuinit usage from all cris files
metag: delete __cpuinit usage from all metag files
tile: delete __cpuinit usage from all tile files
sh: delete __cpuinit usage from all sh files
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Except for a slightly big OMAP changes, all rest are small, mostly
boring changes; all either 3.11 regression fixes or stable materials.
- ASoC OMAP fixes due to non-DT OMAP4 removals
- Other ASoC driver changes (sglt5000, wm8978, wm8948, samsung)
- Fix missing locking for snd_pcm_stop() calls in many drivers
- Fix the blocking request_module() in OSS sequencer
- Fix old OSS vwsnd driver builds
- Add a new HD-audio HDMI codec ID"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: seq-oss: Initialize MIDI clients asynchronously
ALSA: hda - Add new GPU codec ID to snd-hda
staging: line6: Fix unlocked snd_pcm_stop() call
[media] saa7134: Fix unlocked snd_pcm_stop() call
ASoC: s6000: Fix unlocked snd_pcm_stop() call
ASoC: atmel: Fix unlocked snd_pcm_stop() call
ALSA: pxa2xx: Fix unlocked snd_pcm_stop() call
ALSA: usx2y: Fix unlocked snd_pcm_stop() call
ALSA: ua101: Fix unlocked snd_pcm_stop() call
ALSA: 6fire: Fix unlocked snd_pcm_stop() call
ALSA: atiixp: Fix unlocked snd_pcm_stop() call
ALSA: asihpi: Fix unlocked snd_pcm_stop() call
sound: oss/vwsnd: Always define vwsnd_mutex
sound: oss/vwsnd: Add missing inclusion of linux/delay.h
ASoC: wm8978: enable symmetric rates
ASoC: omap-mcbsp: Use different method for DMA request when booted with DT
ASoC: omap-dmic: Do not use platform_get_resource_byname() for DMA
ASoC: omap-mcpdm: Do not use platform_get_resource_byname() for DMA
ASoC: omap-pcm: Request the DMA channel differently when DT is involved
ASoC: Samsung: Set RFS and BFS in slave mode
...
|
|
drm-fixes
Fixes builds
* 'drm/3.11/fixes' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Use the GEM PRIME helpers
drm/shmobile: Use the GEM PRIME helpers
|
|
Recent change to use bio_copy_data() in raid1 when repairing
an array is faulty.
The underlying may have changed the bio in various ways using
bio_advance and these need to be undone not just for the 'sbio' which
is being copied to, but also the 'pbio' (primary) which is being
copied from.
So perform the reset on all bios that were read from and do it early.
This also ensure that the sbio->bi_io_vec[j].bv_len passed to
memcmp is correct.
This fixes a crash during a 'check' of a RAID1 array. The crash was
introduced in 3.10 so this is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit 7ceb17e87bde79d285a8b988cfed9eaeebe60b86
md: Allow devices to be re-added to a read-only array.
allowed a bit more than just that. It also allows devices to be added
to a read-write array and to end up skipping recovery.
This patch removes the offending piece of code pending a rewrite for a
subsequent release.
More specifically:
If the array has a bitmap, then the device will still need a bitmap
based resync ('saved_raid_disk' is set under different conditions
is a bitmap is present).
If the array doesn't have a bitmap, then this is correct as long as
nothing has been written to the array since the metadata was checked
by ->validate_super. However there is no locking to ensure that there
was no write.
Bug was introduced in 3.10 and causes data corruption so
patch is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
1/ When an different between blocks is found, data is copied from
one bio to the other. However bv_len is used as the length to
copy and this could be zero. So use r10_bio->sectors to calculate
length instead.
Using bv_len was probably always a bit dubious, but the introduction
of bio_advance made it much more likely to be a problem.
2/ When preparing some blocks for sync, we don't set BIO_UPTODATE
except on bios that we schedule for a read. This ensures that
missing/failed devices don't confuse the loop at the top of
sync_request write.
Commit 8be185f2c9d54d6 "raid10: Use bio_reset()"
removed a loop which set BIO_UPTDATE on all appropriate bios.
So we need to re-add that flag.
These bugs were introduced in 3.10, so this patch is suitable for
3.10-stable, and can remove a potential for data corruption.
Cc: stable@vger.kernel.org (3.10)
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
more DPM fixes for radeon.
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: add debugfs support for RS780/RS880 (v3)
drm/radeon/dpm/atom: fix broken gcc harder
drm/radeon/dpm/atom: restructure logic to work around a compiler bug
drm/radeon/dpm: fix atom vram table parsing
drm/radeon: fix an endian bug in atom table parsing
drm/radeon: add a module parameter to disable aspm
|
|
Starting from win8, MS backlight control driver will set bit 2 of the
parameter of control method _DOS, to inform firmware it should not
perform any automatic brightness changes. This mostly affects hotkey
notification deliver - if we do not set this bit, on hotkey press,
firmware may choose to adjust brightness level instead of sending out
notification and doing nothing.
So this patch sets bit 2 when calling _DOS so that GUIs can show the
notification window on hotkey press. This behavior change is only
necessary for win8 systems.
The MS document on win8 backlight control is here:
http://msdn.microsoft.com/en-US/library/windows/hardware/jj159305
References: https://bugzilla.kernel.org/show_bug.cgi?id=52951
References: https://bugzilla.kernel.org/show_bug.cgi?id=56711
Reported-by: Micael Dias <kam1kaz3@gmail.com>
Reported-by: Dan Garton <dan.garton@gmail.com>
Reported-by: Bob Ziuchkovski <bob.ziuchkovski@gmail.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
According to Matthew Garrett, "Windows 8 leaves backlight control up
to individual graphics drivers rather than making ACPI calls itself.
There's plenty of evidence to suggest that the Intel driver for
Windows [8] doesn't use the ACPI interface, including the fact that
it's broken on a bunch of machines when the OS claims to support
Windows 8. The simplest thing to do appears to be to disable the
ACPI backlight interface on these systems".
There's a problem with that approach, however, because simply
avoiding to register the ACPI backlight interface if the firmware
calls _OSI for Windows 8 may not work in the following situations:
(1) The ACPI backlight interface actually works on the given system
and the i915 driver is not loaded (e.g. another graphics driver
is used).
(2) The ACPI backlight interface doesn't work on the given system,
but there is a vendor platform driver that will register its
own, equally broken, backlight interface if not prevented from
doing so by the ACPI subsystem.
Therefore we need to allow the ACPI backlight interface to be
registered until the i915 driver is loaded which then will unregister
it if the firmware has called _OSI for Windows 8 (or will register
the ACPI video driver without backlight support if not already
present).
For this reason, introduce an alternative function for registering
ACPI video, acpi_video_register_with_quirks(), that will check
whether or not the ACPI video driver has already been registered
and whether or not the backlight Windows 8 quirk has to be applied.
If the quirk has to be applied, it will block the ACPI backlight
support and either unregister the backlight interface if the ACPI
video driver has already been registered, or register the ACPI
video driver without the backlight interface otherwise. Make
the i915 driver use acpi_video_register_with_quirks() instead of
acpi_video_register() in i915_driver_load().
This change is based on earlier patches from Matthew Garrett,
Chun-Yi Lee and Seth Forshee and includes a fix from Aaron Lu's.
References: https://bugzilla.kernel.org/show_bug.cgi?id=51231
Tested-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Tested-by: Yves-Alexis Perez <corsac@debian.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
Set temporary variable as 0 to avoid garbage string output from
/proc/iomem after register resources and reset to PNP dev name
later.
Signed-off-by: Liu ShuoX <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We have to call acpi_video_init_brightness() even if we're not going
to initialise the backlight - Thinkpads seem to use this as the
trigger for enabling ACPI notifications rather than handling it in
firmware.
[rjw: Drop the brightness object created by
acpi_video_init_brightness() if we are not going to use it.]
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Expose acpi_gbl_osi_data so that code outside of ACPICA can check
the value of the last successfull _OSI call. The definitions for
OSI versions are moved to actypes.h so that other components can
access them too.
Based on a patch from Matthew Garrett which in turn was based on
an earlier patch from Seth Forshee.
[rjw: Changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This allows you to look at the current DPM state via
debugfs.
Due to the way the hardware works on these asics, there's
no way to look up exactly what power state we are in, so
we make the best guess we can based on the current sclk.
v2: Anthoine's version
v3: fix ref div
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
See bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=66932
https://bugs.freedesktop.org/show_bug.cgi?id=66972
https://bugs.freedesktop.org/show_bug.cgi?id=66945
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Due to commit 3683243b ("xen-netfront: use __pskb_pull_tail to ensure
linear area is big enough on RX") xennet_fill_frags() may end up
filling MAX_SKB_FRAGS + 1 fragments in a receive skb, and only reduce
the fragment count subsequently via __pskb_pull_tail(). That's a
result of xennet_get_responses() allowing a maximum of one more slot to
be consumed (and intermediately transformed into a fragment) if the
head slot has a size less than or equal to RX_COPY_THRESHOLD.
Hence we need to adjust xennet_fill_frags() to pull earlier if we
reached the maximum fragment count - due to the described behavior of
xennet_get_responses() this guarantees that at least the first fragment
will get completely consumed, and hence the fragment count reduced.
In order to not needlessly call __pskb_pull_tail() twice, make the
original call conditional upon the pull target not having been reached
yet, and defer the newly added one as much as possible (an alternative
would have been to always call the function right before the call to
xennet_fill_frags(), but that would imply more frequent cases of
needing to call it twice).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: stable@vger.kernel.org (3.6 onwards)
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The socket management is now done in workqueue (outside of RTNL)
and protected by vn->sock_lock. There were two possible bugs, first
the vxlan device was removed from the VNI hash table per socket without
holding lock. And there was a race when device is created and the workqueue
could run after deletion.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems gcc 4.8.1 generates bogus code for the old logic causing
part of the function to get skipped.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=66932
https://bugs.freedesktop.org/show_bug.cgi?id=66972
https://bugs.freedesktop.org/show_bug.cgi?id=66945
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Parsing the table in incorrectly led to problems with
certain asics with mclk switching.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Can cause hangs when enabled in certain motherboards.
Set radeon.aspm=0 to disable aspm.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The GEM CMA PRIME import/export helpers have been removed in favor of
generic GEM PRIME helpers with GEM CMA low-level operations. Fix the
driver accordingly.
Reported-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Mark Brown <broonie@linaro.org>
|
|
The GEM CMA PRIME import/export helpers have been removed in favor of
generic GEM PRIME helpers with GEM CMA low-level operations. Fix the
driver accordingly.
Reported-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Mark Brown <broonie@linaro.org>
|
|
SG mode is not currently supported by netvsc, so remove this flag for now.
Otherwise, it will be unconditionally enabled by commit ec5f0615642
"Kill link between CSUM and SG features"
Previously, the SG feature is disabled because CSUM is not set here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix new kernel-doc warning in drivers/base/platform.c:
Warning(drivers/base/platform.c:528): No description found for parameter 'owner'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
The first round of IIO fixes for the 3.11 cycle.
This set is larger than I would like, partly due to my lack of review
time in the weeks before the merge window and partly because a
couple of large drivers and the subsystem as a whole seem to be
getting a lot more exposure and testing recently.
1) A long term bug in trigger handling gave a double free of the device.
2) Wrong return value handling means offsets are ignored in
iio_convert_raw_to_processed_unlocked.
3) The iio_channel_has_info utility function was incorrectly updated
during the recent info_mask split, this is now fixed.
4) mxs-lradc has a couple of little fixes.
5) A couple of missing .driver_module entries meant that drivers
could be removed from underneath their users.
6) Error path fixes for ad7303 and lis3l02dq.
7) The scale value for presure in the lps331ap driver was out by
a factor of 100.
|
|
This driver is not being updated as the specifications are not able to
be gotten from CSR or anyone else. Without those, getting this driver
into proper mergable shape is going to be impossible. So remove the
driver from the tree.
If the specifications ever become available, this patch can be reverted
and the driver fixed up properly.
Reported-by: Lidza Louina <lidza.louina@gmail.com>
Cc: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Cc: Mikko Virkkilä <mikko.virkkila@bluegiga.com>
Cc: Lauri Hintsala <Lauri.Hintsala@bluegiga.com>
Cc: Riku Mettälä <riku.mettala@bluegiga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://people.freedesktop.org/~danvet/drm-intel
One feature latecomer, I've forgotten to merge the patch to reeanble the
Haswell power well feature now that the audio interaction is fixed up.
Since that was the only unfixed issue with it I've figured I could throw
it in a bit late, and it's trivial to revert in case I'm wrong.
Otherwise all bug/regression fixes:
- Fix status page reinit after gpu hangs, spotted by more paranoid igt
checks.
- Fix object list walking fumble regression in the shrinker (only the
counting part, the actual shrinking code was correct so no Oops
potential), from Xiong Zhang.
- Fix DP 1.2 bw limits (Imre).
- Restore legacy forcewake on ivb, too many broken biosen out there. We
dump a warn though that recent userspace might fall over with that
config (Guenter Roeck).
- Patch up the gen2 cs tlb w/a.
- Improve the fence coherency w/a now that we have a better understanding
what's going on. The removed wbinvd+ipi should make -rt folks happy. Big
thanks to Jon Bloomfield for figuring this out, patches from Chris.
- Fix write-read race when switching ring (Chris). Spotted with code
inspection, but now we also have an igt for it.
There's an ugly regression we're still working on introduced between
3.10-rc7 and 3.10.0. Unfortunately we can't just revert the offender since
that one fixes another regression :( I've asked Steven to include my
-fixes branch into linux-next to prevent such fallout in the future,
hopefully.
* tag 'drm-intel-fixes-2013-07-11' of git://people.freedesktop.org/~danvet/drm-intel:
Revert "drm/i915: Workaround incoherence between fences and LLC across multiple CPUs"
drm/i915: Fix incoherence with fence updates on Sandybridge+
drm/i915: Fix write-read race with multiple rings
Partially revert "drm/i915: unconditionally use mt forcewake on hsw/ivb"
drm/i915: fix lane bandwidth capping for DP 1.2 sinks
drm/i915: fix up ring cleanup for the i830/i845 CS tlb w/a
drm/i915: Correct obj->mm_list link to dev_priv->dev_priv->mm.inactive_list
drm/i915: switch disable_power_well default value to 1
drm/i915: reinit status page registers after gpu reset
|
|
commit 2f7021a8 "cpufreq: protect 'policy->cpus' from offlining
during __gov_queue_work()" caused a regression in CPU hotplug,
because it lead to a deadlock between cpufreq governor worker thread
and the CPU hotplug writer task.
Lockdep splat corresponding to this deadlock is shown below:
[ 60.277396] ======================================================
[ 60.277400] [ INFO: possible circular locking dependency detected ]
[ 60.277407] 3.10.0-rc7-dbg-01385-g241fd04-dirty #1744 Not tainted
[ 60.277411] -------------------------------------------------------
[ 60.277417] bash/2225 is trying to acquire lock:
[ 60.277422] ((&(&j_cdbs->work)->work)){+.+...}, at: [<ffffffff810621b5>] flush_work+0x5/0x280
[ 60.277444] but task is already holding lock:
[ 60.277449] (cpu_hotplug.lock){+.+.+.}, at: [<ffffffff81042d8b>] cpu_hotplug_begin+0x2b/0x60
[ 60.277465] which lock already depends on the new lock.
[ 60.277472] the existing dependency chain (in reverse order) is:
[ 60.277477] -> #2 (cpu_hotplug.lock){+.+.+.}:
[ 60.277490] [<ffffffff810ac6d4>] lock_acquire+0xa4/0x200
[ 60.277503] [<ffffffff815b6157>] mutex_lock_nested+0x67/0x410
[ 60.277514] [<ffffffff81042cbc>] get_online_cpus+0x3c/0x60
[ 60.277522] [<ffffffff814b842a>] gov_queue_work+0x2a/0xb0
[ 60.277532] [<ffffffff814b7891>] cs_dbs_timer+0xc1/0xe0
[ 60.277543] [<ffffffff8106302d>] process_one_work+0x1cd/0x6a0
[ 60.277552] [<ffffffff81063d31>] worker_thread+0x121/0x3a0
[ 60.277560] [<ffffffff8106ae2b>] kthread+0xdb/0xe0
[ 60.277569] [<ffffffff815bb96c>] ret_from_fork+0x7c/0xb0
[ 60.277580] -> #1 (&j_cdbs->timer_mutex){+.+...}:
[ 60.277592] [<ffffffff810ac6d4>] lock_acquire+0xa4/0x200
[ 60.277600] [<ffffffff815b6157>] mutex_lock_nested+0x67/0x410
[ 60.277608] [<ffffffff814b785d>] cs_dbs_timer+0x8d/0xe0
[ 60.277616] [<ffffffff8106302d>] process_one_work+0x1cd/0x6a0
[ 60.277624] [<ffffffff81063d31>] worker_thread+0x121/0x3a0
[ 60.277633] [<ffffffff8106ae2b>] kthread+0xdb/0xe0
[ 60.277640] [<ffffffff815bb96c>] ret_from_fork+0x7c/0xb0
[ 60.277649] -> #0 ((&(&j_cdbs->work)->work)){+.+...}:
[ 60.277661] [<ffffffff810ab826>] __lock_acquire+0x1766/0x1d30
[ 60.277669] [<ffffffff810ac6d4>] lock_acquire+0xa4/0x200
[ 60.277677] [<ffffffff810621ed>] flush_work+0x3d/0x280
[ 60.277685] [<ffffffff81062d8a>] __cancel_work_timer+0x8a/0x120
[ 60.277693] [<ffffffff81062e53>] cancel_delayed_work_sync+0x13/0x20
[ 60.277701] [<ffffffff814b89d9>] cpufreq_governor_dbs+0x529/0x6f0
[ 60.277709] [<ffffffff814b76a7>] cs_cpufreq_governor_dbs+0x17/0x20
[ 60.277719] [<ffffffff814b5df8>] __cpufreq_governor+0x48/0x100
[ 60.277728] [<ffffffff814b6b80>] __cpufreq_remove_dev.isra.14+0x80/0x3c0
[ 60.277737] [<ffffffff815adc0d>] cpufreq_cpu_callback+0x38/0x4c
[ 60.277747] [<ffffffff81071a4d>] notifier_call_chain+0x5d/0x110
[ 60.277759] [<ffffffff81071b0e>] __raw_notifier_call_chain+0xe/0x10
[ 60.277768] [<ffffffff815a0a68>] _cpu_down+0x88/0x330
[ 60.277779] [<ffffffff815a0d46>] cpu_down+0x36/0x50
[ 60.277788] [<ffffffff815a2748>] store_online+0x98/0xd0
[ 60.277796] [<ffffffff81452a28>] dev_attr_store+0x18/0x30
[ 60.277806] [<ffffffff811d9edb>] sysfs_write_file+0xdb/0x150
[ 60.277818] [<ffffffff8116806d>] vfs_write+0xbd/0x1f0
[ 60.277826] [<ffffffff811686fc>] SyS_write+0x4c/0xa0
[ 60.277834] [<ffffffff815bbbbe>] tracesys+0xd0/0xd5
[ 60.277842] other info that might help us debug this:
[ 60.277848] Chain exists of:
(&(&j_cdbs->work)->work) --> &j_cdbs->timer_mutex --> cpu_hotplug.lock
[ 60.277864] Possible unsafe locking scenario:
[ 60.277869] CPU0 CPU1
[ 60.277873] ---- ----
[ 60.277877] lock(cpu_hotplug.lock);
[ 60.277885] lock(&j_cdbs->timer_mutex);
[ 60.277892] lock(cpu_hotplug.lock);
[ 60.277900] lock((&(&j_cdbs->work)->work));
[ 60.277907] *** DEADLOCK ***
[ 60.277915] 6 locks held by bash/2225:
[ 60.277919] #0: (sb_writers#6){.+.+.+}, at: [<ffffffff81168173>] vfs_write+0x1c3/0x1f0
[ 60.277937] #1: (&buffer->mutex){+.+.+.}, at: [<ffffffff811d9e3c>] sysfs_write_file+0x3c/0x150
[ 60.277954] #2: (s_active#61){.+.+.+}, at: [<ffffffff811d9ec3>] sysfs_write_file+0xc3/0x150
[ 60.277972] #3: (x86_cpu_hotplug_driver_mutex){+.+...}, at: [<ffffffff81024cf7>] cpu_hotplug_driver_lock+0x17/0x20
[ 60.277990] #4: (cpu_add_remove_lock){+.+.+.}, at: [<ffffffff815a0d32>] cpu_down+0x22/0x50
[ 60.278007] #5: (cpu_hotplug.lock){+.+.+.}, at: [<ffffffff81042d8b>] cpu_hotplug_begin+0x2b/0x60
[ 60.278023] stack backtrace:
[ 60.278031] CPU: 3 PID: 2225 Comm: bash Not tainted 3.10.0-rc7-dbg-01385-g241fd04-dirty #1744
[ 60.278037] Hardware name: Acer Aspire 5741G /Aspire 5741G , BIOS V1.20 02/08/2011
[ 60.278042] ffffffff8204e110 ffff88014df6b9f8 ffffffff815b3d90 ffff88014df6ba38
[ 60.278055] ffffffff815b0a8d ffff880150ed3f60 ffff880150ed4770 3871c4002c8980b2
[ 60.278068] ffff880150ed4748 ffff880150ed4770 ffff880150ed3f60 ffff88014df6bb00
[ 60.278081] Call Trace:
[ 60.278091] [<ffffffff815b3d90>] dump_stack+0x19/0x1b
[ 60.278101] [<ffffffff815b0a8d>] print_circular_bug+0x2b6/0x2c5
[ 60.278111] [<ffffffff810ab826>] __lock_acquire+0x1766/0x1d30
[ 60.278123] [<ffffffff81067e08>] ? __kernel_text_address+0x58/0x80
[ 60.278134] [<ffffffff810ac6d4>] lock_acquire+0xa4/0x200
[ 60.278142] [<ffffffff810621b5>] ? flush_work+0x5/0x280
[ 60.278151] [<ffffffff810621ed>] flush_work+0x3d/0x280
[ 60.278159] [<ffffffff810621b5>] ? flush_work+0x5/0x280
[ 60.278169] [<ffffffff810a9b14>] ? mark_held_locks+0x94/0x140
[ 60.278178] [<ffffffff81062d77>] ? __cancel_work_timer+0x77/0x120
[ 60.278188] [<ffffffff810a9cbd>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[ 60.278196] [<ffffffff81062d8a>] __cancel_work_timer+0x8a/0x120
[ 60.278206] [<ffffffff81062e53>] cancel_delayed_work_sync+0x13/0x20
[ 60.278214] [<ffffffff814b89d9>] cpufreq_governor_dbs+0x529/0x6f0
[ 60.278225] [<ffffffff814b76a7>] cs_cpufreq_governor_dbs+0x17/0x20
[ 60.278234] [<ffffffff814b5df8>] __cpufreq_governor+0x48/0x100
[ 60.278244] [<ffffffff814b6b80>] __cpufreq_remove_dev.isra.14+0x80/0x3c0
[ 60.278255] [<ffffffff815adc0d>] cpufreq_cpu_callback+0x38/0x4c
[ 60.278265] [<ffffffff81071a4d>] notifier_call_chain+0x5d/0x110
[ 60.278275] [<ffffffff81071b0e>] __raw_notifier_call_chain+0xe/0x10
[ 60.278284] [<ffffffff815a0a68>] _cpu_down+0x88/0x330
[ 60.278292] [<ffffffff81024cf7>] ? cpu_hotplug_driver_lock+0x17/0x20
[ 60.278302] [<ffffffff815a0d46>] cpu_down+0x36/0x50
[ 60.278311] [<ffffffff815a2748>] store_online+0x98/0xd0
[ 60.278320] [<ffffffff81452a28>] dev_attr_store+0x18/0x30
[ 60.278329] [<ffffffff811d9edb>] sysfs_write_file+0xdb/0x150
[ 60.278337] [<ffffffff8116806d>] vfs_write+0xbd/0x1f0
[ 60.278347] [<ffffffff81185950>] ? fget_light+0x320/0x4b0
[ 60.278355] [<ffffffff811686fc>] SyS_write+0x4c/0xa0
[ 60.278364] [<ffffffff815bbbbe>] tracesys+0xd0/0xd5
[ 60.280582] smpboot: CPU 1 is now offline
The intention of that commit was to avoid warnings during CPU
hotplug, which indicated that offline CPUs were getting IPIs from the
cpufreq governor's work items. But the real root-cause of that
problem was commit a66b2e5 (cpufreq: Preserve sysfs files across
suspend/resume) because it totally skipped all the cpufreq callbacks
during CPU hotplug in the suspend/resume path, and hence it never
actually shut down the cpufreq governor's worker threads during CPU
offline in the suspend/resume path.
Reflecting back, the reason why we never suspected that commit as the
root-cause earlier, was that the original issue was reported with
just the halt command and nobody had brought in suspend/resume to the
equation.
The reason for _that_ in turn, as it turns out, is that earlier
halt/shutdown was being done by disabling non-boot CPUs while tasks
were frozen, just like suspend/resume.... but commit cf7df378a
(reboot: migrate shutdown/reboot to boot cpu) which came somewhere
along that very same time changed that logic: shutdown/halt no longer
takes CPUs offline. Thus, the test-cases for reproducing the bug
were vastly different and thus we went totally off the trail.
Overall, it was one hell of a confusion with so many commits
affecting each other and also affecting the symptoms of the problems
in subtle ways. Finally, now since the original problematic commit
(a66b2e5) has been completely reverted, revert this intermediate fix
too (2f7021a8), to fix the CPU hotplug deadlock. Phew!
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Cc: 3.10+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Hardware workaround requesting hardware to skip vlan insertion is necessary
only when umc or qnq is enabled. Enabling this workaround in other scenarios
could cause controller to stall.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hard-coded 8021.q proto will break 802.1ad traffic. So switch to use
vlan->proto.
Cc: Basil Gor <basil.gor@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 441ac0fcaadc76ad09771812382345001dd2b813
(macvtap: Convert to using rtnl lock) forget to return what
macvtap_ioctl_set_queue() returns to its caller. This may break multiqueue API
by always falling through to TUNGETFEATURES.
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Eli Cohen <eli@mellanox.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bgmac is using functions from phylib, add the dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ben Hutchings pointed out that my recent update to atl1e
in commit 352900b583b2852152a1e05ea0e8b579292e731e
("atl1e: fix dma mapping warnings") was missing a bit of code.
Specifically it reset the hardware tx ring to its origional state when
we hit a dma error, but didn't unmap any exiting mappings from the
operation. This patch fixes that up. It also remembers to free the
skb in the event that an error occurs, so we don't leak. Untested, as
I don't have hardware. I think its pretty straightforward, but please
review closely.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
