summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2008-01-23libata: zero xfer length on ATAPI data xfer IRQ is HSM violationAlbert Lee
Treat zero xfer length as HSM violation. While at it, add unlikely()'s to ATAPI ireason and transfer length checks. tj: Formatted patch and added unlikely()'s. Signed-off-by: Albert Lee <albertcc@tw.ibm.com> Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: make atapi_request_sense() use sgTejun Heo
atapi_request_sense() is now the only left user of ata_sg_init_one(). Convert it to use sg interface. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Rusty Russel <rusty@rustcorp.com.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: convert NCQ test in ata_qc_issue() to ata_is_ncq()Tejun Heo
I missed one while converting to ata_is_*() protocol test helpers. Convert it. Pointed out by Jeff Garzik. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23pata_hpt37x: checkpatch fixesAndrew Morton
WARNING: line over 80 characters #70: FILE: drivers/ata/pata_hpt37x.c:850: + struct pci_dev *pdev_0 = pci_get_slot(pdev->bus, pdev->devfn - 1); ERROR: else should follow close brace '}' #78: FILE: drivers/ata/pata_hpt37x.c:858: + } + else total: 1 errors, 1 warnings, 100 lines checked Your patch has style problems, please review. If any of these errors are false positives report them to the maintainer, see CHECKPATCH in MAINTAINERS. Please run checkpatch prior to sending patches Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23drivers/ata/libata-eh.c: fix printk warningAndrew Morton
drivers/ata/libata-eh.c: In function `ata_port_pbar_desc': drivers/ata/libata-eh.c:215: warning: long long unsigned int format, long unsigned int arg (arg 4) Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23pata_amd: update mode selection for NV PATAsTejun Heo
Cable detection on NV PATA hosts isn't implemented and the CBLID- cable isn't wired according to the sepc either, so both host-side and generic drive-side cable detections are broken. Till now, nv_cable_detect() relied on peeking BIOS and ACPI configurations to upgrade to 80C but this often results in misdetection of 40C cable as 80C. Also, the original implementation was broken in that by the time BIOS configuration is read it has already been cleared by programming PIO0 during reset. This patch reimplements NV mode selection such that... * BIOS configuration value is stored during driver attach and restored on detach. * Cable type is fixed to ATA_CBL_PATA_IGN and mode selection is soley done by nv_mode_filter() which peeks both BIOS and ACPI configurations and filter accordingly. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: reimplement ata_acpi_cbl_80wire() using ata_acpi_gtm_xfermask()Tejun Heo
Reimplement ata_acpi_cbl_80wire() using ata_acpi_gtm_xfermask() and while at it relocate the function below ata_acpi_gtm_xfermask(). New ata_acpi_cbl_80wire() implementation takes @gtm, in both pata_via and pata_amd, use the initial GTM value. Both are trying to peek initial BIOS configuration, so using initial caching value makes sense. This fixes ACPI part of cable detection in pata_amd which previously always returned 0 because configuring PIO0 during reset clears DMA configuration. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: implement ata_timing_cycle2mode() and use it in libata-acpi and ↵Tejun Heo
pata_acpi libata-acpi is using separate timing tables for transfer modes although libata-core has the complete ata_timing table. Implement ata_timing_cycle2mode() to look for matching mode given transfer type and cycle duration and use it in libata-acpi and pata_acpi to replace private timing tables. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: fix ata_acpi_gtm_xfermask()Tejun Heo
ata_acpi_gtm_xfermask() as separated out from pacpi_discover_modes() has various bugs. Fix them. * The wrong comparison operator is used when finding for matching cycle resulting totally bogus result. * With the comparion operator fixed, boundary condtion handling is clumsy. * Setting of any DMA mask bit set all bits in PIO mask. * MWDMA and UDMA blocks are swapped. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: separate out ata_acpi_gtm_xfermask() from pacpi_discover_modes()Tejun Heo
Finding out matching transfer mode from ACPI GTM values is useful for other purposes too. Separate out the function and timing tables from pata_acpi::pacpi_discover_modes(). Other than checking shared-configuration bit after doing ata_acpi_gtm() in pacpi_discover_modes() which should be safe, this patch doesn't introduce any behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23ata_piix: separate controller IDs into separate enumTejun Heo
Separate controller IDs into a separate enum as Jeff requested. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23sata_promise: make pdc_atapi_pkt() use values from qc->tfTejun Heo
Make pdc_atapi_pkt() use values from qc->tf instead of creating its own. This is to ease future ATAPI handling changes. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: add ATA_CBL_PATA_IGNTejun Heo
ATA_CBL_PATA_UNK indicates that the cable type can't be determined from the host side and might be either 80c or 40c. libata applies drive or other generic limit in this case. However, there are controllers where both host and drive side detections are misimplemented and the driver has to rely solely on private method - peeking BIOS or ACPI configuration or using some other private mechanism. This patch adds ATA_CBL_PATA_IGN which tells libata to ignore the cable type completely and just let the LLD determine the transfer mode via host transfer mode masks and ->mode_filter(). Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: xfer_mask is unsigned long not unsigned intTejun Heo
Jeff says xfer_mask is unsigned long not unsigned int. Convert all xfermask fields and handling functions to deal with unsigned longs. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: kill ata_id_to_dma_mode()Tejun Heo
ata_id_to_dma_mode() isn't quite generic. The function is basically privately implemented ata_id_xfermask() combined with hardcoded mode printing and configuration which are specific to ata_generic. Kill the function and open code it in generic_set_mode() using generic xfermode handling functions. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: clean up xfermode / PATA timing related stuffTejun Heo
* s/ATA_BITS_(PIO|MWDMA|UDMA)/ATA_NR_\1_MODES/g * Consistently use 0xff to indicate invalid transfer mode (0x00 is valid for PIO_SLOW). * Make ata_xfer_mode2mask() return proper mode mask instead of just the highest bit. * Sort ata_timing table in increasing xfermode order and update ata_timing_find_mode() accordingly. This patch doesn't introduce any behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: export xfermode / PATA timing related functionsTejun Heo
Export the following xfermode related functions. * ata_pack_xfermask() * ata_unpack_xfermask() * ata_xfer_mask2mode() * ata_xfer_mode2mask() * ata_xfer_mode2shift() * ata_mode_string() * ata_id_xfermask() * ata_timing_find_mode() These functions will be used later by LLD updates. While at it, change unsigned short @speed to u8 @xfer_mode in ata_timing_find_mode() for consistency. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23ata_generic: unindent loop in generic_set_mode()Tejun Heo
Unindent loop body in generic_set_mode(). This is to ease future change. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23[libata] Build fix WRT ata_is_xxx() new API introductionJeff Garzik
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23libata: implement fast speed down for unverified data transfer modeTejun Heo
It's very likely that the configured data transfer mode is the wrong one if device fails data transfers right after initial data transfer mode configuration (including NCQ on/off and xfermode). libata EH needs to speed down fast before upper layers give up on probing. This patch implement fast speed down rules to handle such cases better. Error occured while data transfer hasn't been verified trigger fast back-to-back speed down actions until data transfer works. This change will make cable mis-detection and other initial configuration problems corrected before partition scanning code gives up. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: implement ATA_DFLAG_DUBIOUS_XFERTejun Heo
ATA_DFLAG_DUBIOUS_XFER is set whenever data transfer speed or method changes and gets cleared when data transfer command succeeds in the newly configured transfer mode. This will be used to improve speed down logic. Signed-off-by: Tejun Heo <htejun@gmail.com< Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: adjust speed down rulesTejun Heo
Speed down rules were too conservative. Adjust them a bit. * More than 10 timeouts can't happen in 5 minutes as command timeout is 30secs. Lower the limit for rule #1 to 6. * 10 timeouts is too high for rule #3 too. Lower it to 6. * SATAPI can benefit from falling back to PIO too. Allow SATAPI devices to fall back to PIO. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: clean up EH speed down implementationTejun Heo
Clean up EH speed down implementation. * is_io boolean variable is replaced eflags. is_io is ATA_EFLAG_IS_IO. * Error categories now have names. * Better comments. * Reorder 5min and 10min rules in ata_eh_speed_down_verdict() * Use local variable @link to cache @dev->link in ata_eh_speed_down() These changes are to improve readability and ease further changes. This patch doesn't introduce any behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: move ata_set_mode() to libata-eh.cTejun Heo
Move ata_set_mode() to libata-eh.c. ata_set_mode() is surely an EH action and will be more tightly coupled with the rest of error handling. Move it to libata-eh.c. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: factor out ata_eh_schedule_probe()Tejun Heo
Factor out ata_eh_schedule_probe() from ata_eh_handle_dev_fail() and ata_eh_recover(). This is to improve maintainability and make future changes easier. In the previous revision, ata_dev_enabled() test was accidentally dropped while factoring out. This problem was spotted by Bartlomiej. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: implement protocol testsTejun Heo
Implement protocol tests - ata_is_atapi(), ata_is_nodata(), ata_is_pio(), ata_is_dma(), ata_is_ncq() and ata_is_data() and use them to replace is_atapi_taskfile() and hard coded protocol tests. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: checkpatch fixesJeff Garzik
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23ahci: update PCS programmingTejun Heo
For intel ones, ahci unconditionally OR'd 0xf to PCS. This isn't correct for the following cases. * ich6/7m's which only implement P0 and P2 (0xf works fine tho) * ich8/9's which have six ports and needs 0x3f to enable all ports This patch updates PCS programming such that... * port_map determined by ahci_save_initial_config() is OR'd instead of 0xf * PCS is updated only if necessary (there are turned off enable bits) port_map is determined from PORTS_IMPL PCI register which is implemented as write or write-once register. If the register isn't programmed, ahci automatically generates it from number of ports, which is good enough for PCS programming. ICH6/7M are probably the only ones where non-contiguous enable bits are necessary && PORTS_IMPL isn't programmed properly but they're proven to work reliably with 0xf anyway. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23pata_ninja32: Cardbus ATA initial supportAlan Cox
Lots of work needed to bring it up to scratch but it does work so you can now use the card. That makes it at least useful, especially as the other cardbus cards are usually INIC162x which aren't yet supported well. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata-sff: tf_loadAlan Cox
Jeff said he preferred that the SFF tf_load followed the spec and we documented that anyone who needed different overrode it, rather than it using the ->check_status methods. No driver relies on the current behaviour. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata: IORDY handlingAlan Cox
I believe this version meets all Sergei's objections Correct the logic for when we issue a set features for transfer mode - If the device has IORDY and the controller has IORDY - set the mode - If the device has IORDY and the controller does not - turn IORDY off - If neither has IORDY do nothing Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23libata-acpi: add ACPI _PSx methodShaohua Li
ACPI spec (ver 3.0a, p289) requires IDE power on/off executes ACPI _PSx methods. As recently most PATA drivers use libata, this patch adds _PSx method support in libata. ACPI spec doesn't mention if SATA requires the same _PSx method. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Acked-by: Len Brown <len.brown@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23libata: Disable ATA8-ACS proposed Trusted Computing features by defaultAlan Cox
Historically word 48 in the identify data was used to mean 32bit I/O was supported for VLB IDE etc. ATA8 reassigns this word to the Trusted Computing Group, where it is used for TCG features. This means that an ATA8 TCG drive is going to trigger 32bit I/O on some systems which will be funny. Anyway we need to sort this out ready for ATA8 so: - Reorder the ata.h header a bit so the ata_version function occurs early in it - Make dword_io check the ATA version - Add an ATA8 version checking TCG presence test While we are at it the current drafts have a flaw where it may not be possible to disable TCG features at boot (and opt out of the trusted model) as TCG intends because it relies on presence of a different optional feature (DCS). Handle this in software by refusing the TCG commands if libata.allow_tpm is not set. (We must make it possible as some environments such as proprietary VDR devices will doubtless want to use it to lock up content) Finally as with CPRM print a warning so that the user knows they may not be able to full access and use the device. Signed-off-by: Alan Cox <alan@redhat.com>
2008-01-23ata_piix: Add Toshiba Satellite R20 and Tecra M6 to broken suspend list.Peter Schwenke
Add Toshiba Satellite R20 and Tecra M6 to broken suspend list. Matt Piermarini reported and provided the M6 patch. This is from OSDL bug 7780. Signed-off-by: Peter Schwenke <peter@bluetoad.com.au> Cc: Matt Piermarini <mattpiermarini@yahoo.com> Acked-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-22Fix file references in documentation and KconfigJohann Felix Soden
Fix typo in arch/powerpc/boot/flatdevtree_env.h. There is no Documentation/networking/ixgbe.txt. README.cycladesZ is now in Documentation/. wavelan.p.h is now in drivers/net/wireless/. HFS.txt is now Documentation/filesystems/hfs.txt. OSS-files are now in sound/oss/. Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-22Merge branch 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6Linus Torvalds
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: hwmon: (it87) request only Environment Controller ports
2008-01-22W1: w1_therm.c is flagging 0C etc as invalidDavid Fries
The extra rom[0] check is flagging valid temperatures as invalid when there is already a CRC data transmission check. w1_therm_read_bin() if (rom[8] == crc && rom[0]) verdict = 1; Requiring rom[0] to be non-zero will flag as invalid temperature conversions when the low byte is zero, specifically the temperatures 0C, 16C, 32C, 48C, -16C, -32C, and -48C. The CRC check is produced on the device for the previous 8 bytes and is required to ensure the data integrity in transmission. I don't see why the extra check for rom[0] being non-zero is in there. Evgeniy Polyakov didn't know either. Just for a check I unplugged the sensor, executed a temperature conversion, and read the results. The read was all ff's, which also failed the CRC, so it doesn't need to protect against a disconnected sensor. I have more extensive patches in the work, but these two trivial ones will do for today. I would like to hear from people who use the ds2490 USB to one wire dongle. 1 if you would be willing to test the patches as I currently only have the one sensor on a short parisite powered wire, 2 if there is any cheap sources for the ds2490. Signed-off-by: David Fries <david@fries.net> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-22W1: w1_therm.c ds18b20 decode freezing temperatures correctlyDavid Fries
Correct the decoding of negative C temperatures. The code did a binary OR of two bytes to make a 16 bit value, but assignd it to an integer. This caused the value to not be sign extended and to loose that it was a negative number in the assignment. Before the patch (in my freezer), w1_slave ed fe 4b 46 7f ff 03 10 e4 : crc=e4 YES ed fe 4b 46 7f ff 03 10 e4 t=4078 With the patch, e3 fe 4b 46 7f ff 0d 10 81 : crc=81 YES e3 fe 4b 46 7f ff 0d 10 81 t=-17 Signed-off-by: David Fries <david@fries.net> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-22hwmon: (it87) request only Environment Controller portsBjorn Helgaas
The IT8705F and related parts are Super I/O controllers that contain many separate devices. Some BIOSes describe IT8705F I/O port usage under a motherboard device (PNP0C02) with overlapping regions, e.g., 0x290-0x29f and 0x290-0x294. The it87 driver supports only the Environment Controller, which requires only two ISA ports, but it used to request an eight-port range. If that range exceeds a range reported by the BIOS, as 0x290-0x297 would, the request fails, and the it87 driver cannot claim the device. This patch makes the it87 driver request only the two ports used for the Environment Controller device. Systems where this problem has been reported: Gigabyte GA-K8N Ultra 9 Gigabyte M56S-S3 Gigabyte GA-965G-DS3 Kernel bug reports: http://bugzilla.kernel.org/show_bug.cgi?id=9514 http://lkml.org/lkml/2007/12/4/466 Related change: http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=a7839e960675b549f06209d18283d5cee2ce9261 The patch above increases the number of PNP port resources we support. Prior to this patch, we ignored some port resources, which masked the it87 problem. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
2008-01-21Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: [ICMP]: ICMP_MIB_OUTMSGS increment duplicated [IPV6]: RFC 2011 compatibility broken [IPV6]: ICMP6_MIB_OUTMSGS increment duplicated [NET]: rtnl_link: fix use-after-free [AF_KEY]: Fix skb leak on pfkey_send_migrate() error [ATM] atm/suni.c: Fix section mismatch. [ATM] atm/idt77105.c: Fix section mismatch. [IrDA]: af_irda memory leak fixes [NEIGH]: Revert 'Fix race between neigh_parms_release and neightbl_fill_parms' [NETFILTER]: bridge-netfilter: fix net_device refcnt leaks [IPV6] ROUTE: Make sending algorithm more friendly with RFC 4861. [IPV4] FIB_HASH : Avoid unecessary loop in fn_hash_dump_zone() [NET]: Fix interrupt semaphore corruption in Intel drivers. [IPV4] fib_trie: fix duplicated route issue [IPV4] fib_hash: fix duplicated route issue [IPV6]: Mischecked tw match in __inet6_check_established. rfkill: call rfkill_led_trigger_unregister() on error
2008-01-21Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: tc35815: Use irq number for tc35815-mac platform device id [MIPS] Malta: Fix reading the PCI clock frequency on big-endian [MIPS] SMTC: Fix build error.
2008-01-21s3c2410_fb: fix line length calculationStefan Schmidt
Fix line length calculation. var->width is the size of the display in mm. We like to use the pixel size. Without this fix, dynamic (fbset) based resolution and depths changes with s3c2410_fb don't work at all. Spotted by john cass <johnpcass@yahoo.com> Signed-off-by: Stefan Schmidt <stefan@openmoko.org> Signed-off-by: Harald Welte <laforge@openmoko.org> Acked-by: Ben Dooks <ben-linux@fluff.org> Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
2008-01-21keyspan: fix oopsAlan Cox
If we get a data URB back from the hardware after we have put the tty to bed we go kaboom. Fortunately all we need to do is process the URB without trying to ram its contents down the throat of an ex-tty. Signed-off-by: Alan Cox <alan@redhat.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
2008-01-22tc35815: Use irq number for tc35815-mac platform device idAtsushi Nemoto
The tc35815-mac platform device used a pci bus number and a devfn to identify its target device, but the pci bus number may vary if some bus-bridges are found. Use irq number which is be unique for embedded controllers. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-01-20[NET]: rtnl_link: fix use-after-freePatrick McHardy
When unregistering the rtnl_link_ops, all existing devices using the ops are destroyed. With nested devices this may lead to a use-after-free despite the use of for_each_netdev_safe() in case the upper device is next in the device list and is destroyed by the NETDEV_UNREGISTER notifier. The easy fix is to restart scanning the device list after removing a device. Alternatively we could add new devices to the front of the list to avoid having dependant devices follow the device they depend on. A third option would be to only restart scanning if dev->iflink of the next device matches dev->ifindex of the current one. For now this seems like the safest solution. With this patch, the veth rtnl_link_ops unregistration can use rtnl_link_unregister() directly since it now also handles destruction of multiple devices at once. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-20[ATM] atm/suni.c: Fix section mismatch.Adrian Bunk
EXPORT_SYMBOL'ed code mustn't be __*init. Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-20[ATM] atm/idt77105.c: Fix section mismatch.Adrian Bunk
EXPORT_SYMBOL'ed code mustn't be __*init. Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-20[NET]: Fix interrupt semaphore corruption in Intel drivers.David S. Miller
Several of the Intel ethernet drivers keep an atomic counter used to manage when to actually hit the hardware with a disable or an enable. The way the net_rx_work() breakout logic works during a pending napi_disable() is that it simply unschedules the poll even if it still has work. This can potentially leave interrupts disabled, but that is OK because all of the drivers are about to disable interrupts anyways in all such code paths that do a napi_disable(). Unfortunately, this trips up the semaphore used here in the Intel drivers. If you hit this case, when you try to bring the interface back up it won't enable interrupts. A reload of the driver module fixes it of course. So what we do is make sure all the sequences now go: napi_disable(); atomic_set(&adapter->irq_sem, 0); *_irq_disable(); which makes sure the counter is always in the correct state. Reported by Robert Olsson. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-19Remove bogus duplicate CONFIG_LGUEST_GUEST entry.Rusty Russell
It was moved to arch/x86/lguest/Kconfig, but I lost the deletion part in a patch suffle. My confused one-liner "fix" to turn it on is also reverted: 84f7466ee20cc094aa38617abfa2f3834871f054 Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-19pata_pdc202xx_old: Fix crashes with ATAPIAlan Cox
The PDC202xx older devices do not support ATAPI DMA via the usual interfaces. What documentation I have isn't sufficient to support DMA and it isn't clear if the Windows drivers do this or it is possible at all. (Neither do the drivers/ide old drivers) So turn it ATAPI DMA off, these are disk optimised controllers. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-08-26 03:22:01 +0000