| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 848b159835ddef99cc4193083f7e786c3992f580 ]
with the introduction of commit
b0eb57cb97e7837ebb746404c2c58c6f536f23fa, it appears that rq->buf_info
is improperly handled. While it is heap allocated when an rx queue is
setup, and freed when torn down, an old line of code in
vmxnet3_rq_destroy was not properly removed, leading to rq->buf_info[0]
being set to NULL prior to its being freed, causing a memory leak, which
eventually exhausts the system on repeated create/destroy operations
(for example, when the mtu of a vmxnet3 interface is changed
frequently.
Fix is pretty straight forward, just move the NULL set to after the
free.
Tested by myself with successful results
Applies to net, and should likely be queued for stable, please
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-By: boyang@redhat.com
CC: boyang@redhat.com
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: David S. Miller <davem@davemloft.net>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0d9c9f0f40ca262b67fc06a702b85f3976f5e1a1 ]
sts variable is holding link speed as well as state. We should
be using ls to index into ls_to_ethtool.
Fixes: 265aeb511bd5 ("nfp: add support for .get_link_ksettings()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e58edaa4863583b54409444f11b4f80dff0af1cd ]
Helmut reported a bug about division by zero while
running traffic and doing physical cable pull test.
When the cable unplugged the ppms become zero, so when
dividing the current ppms by the previous ppms in the
next dim iteration there is division by zero.
This patch prevent this division for both ppms and epms.
Fixes: c3164d2fc48f ("net/mlx5e: Added BW check for DIM decision mechanism")
Reported-by: Helmut Grauer <helmut.grauer@de.ibm.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4df0bfc79904b7169dc77dcce44598b1545721f9 ]
tfile->tun could be detached before we close the tun fd,
via tun_detach_all(), so it should not be used to check for
tfile->tx_array.
As Jason suggested, we probably have to clean it up
unconditionally both in __tun_deatch() and tun_detach_all(),
but this requires to check if it is initialized or not.
Currently skb_array_cleanup() doesn't have such a check,
so I check it in the caller and introduce a helper function,
it is a bit ugly but we can always improve it in net-next.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 1576d9860599 ("tun: switch to use skb array for tx")
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1ecdaea02ca6bfacf2ecda500dc1af51e9780c42 ]
Driver periodically samples all neighbors configured in device
in order to update the kernel regarding their state. When finding
an entry configured in HW that doesn't show in neigh_lookup()
driver logs an error message.
This introduces a race when removing multiple neighbors -
it's possible that a given entry would still be configured in HW
as its removal is still being processed but is already removed
from the kernel's neighbor tables.
Simply remove the error message and gracefully accept such events.
Fixes: c723c735fa6b ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Fixes: 60f040ca11b9 ("mlxsw: spectrum_router: Periodically dump active IPv6 neighbours")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 52acf06451930eb4cefabd5ecea56e2d46c32f76 ]
The commit 622190669403 ("be2net: Request RSS capability of Rx interface
depending on number of Rx rings") modified be_update_queues() so the
IFACE (HW representation of the netdevice) is destroyed and then
re-created. This causes a regression because potential promiscuous mode
is not restored properly during be_open() because the driver thinks
that the HW has promiscuous mode already enabled.
Note that Lancer is not affected by this bug because RX-filter flags are
disabled during be_close() for this chipset.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: 622190669403 ("be2net: Request RSS capability of Rx interface depending on number of Rx rings")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0171c41835591e9aa2e384b703ef9a6ae367c610 ]
ppp_dev_uninit(), which is the .ndo_uninit() handler of PPP devices,
needs to lock pn->all_ppp_mutex. Therefore we mustn't call
register_netdevice() with pn->all_ppp_mutex already locked, or we'd
deadlock in case register_netdevice() fails and calls .ndo_uninit().
Fortunately, we can unlock pn->all_ppp_mutex before calling
register_netdevice(). This lock protects pn->units_idr, which isn't
used in the device registration process.
However, keeping pn->all_ppp_mutex locked during device registration
did ensure that no device in transient state would be published in
pn->units_idr. In practice, unlocking it before calling
register_netdevice() doesn't change this property: ppp_unit_register()
is called with 'ppp_mutex' locked and all searches done in
pn->units_idr hold this lock too.
Fixes: 8cb775bc0a34 ("ppp: fix device unregistration upon netns deletion")
Reported-and-tested-by: syzbot+367889b9c9e279219175@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8978cc921fc7fad3f4d6f91f1da01352aeeeff25 ]
There are systems platform information management interfaces (such as
HOST2BMC) for which we cannot disable local loopback multicast traffic.
Separate disable_local_lb_mc and disable_local_lb_uc capability bits so
driver will not disable multicast loopback traffic if not supported.
(It is expected that Firmware will not set disable_local_lb_mc if
HOST2BMC is running for example.)
Function mlx5_nic_vport_update_local_lb will do best effort to
disable/enable UC/MC loopback traffic and return success only in case it
succeeded to changed all allowed by Firmware.
Adapt mlx5_ib and mlx5e to support the new cap bits.
Fixes: 2c43c5a036be ("net/mlx5e: Enable local loopback in loopback selftest")
Fixes: c85023e153e3 ("IB/mlx5: Add raw ethernet local loopback support")
Fixes: bded747bb432 ("net/mlx5: Add raw ethernet local loopback firmware command")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a78e93661c5fd30b9e1dee464b2f62f966883ef7 ]
Hardware statistics retrieval hurts in tight invocation loops.
Avoid extraneous write and enforce strict ordering of writes targeted to
the tally counters dump area address registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Oliver Freyermuth <o.freyermuth@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 02612bb05e51df8489db5e94d0cf8d1c81f87b0c ]
In pppoe_sendmsg(), reserving dev->hard_header_len bytes of headroom
was probably fine before the introduction of ->needed_headroom in
commit f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom").
But now, virtual devices typically advertise the size of their overhead
in dev->needed_headroom, so we must also take it into account in
skb_reserve().
Allocation size of skb is also updated to take dev->needed_tailroom
into account and replace the arbitrary 32 bytes with the real size of
a PPPoE header.
This issue was discovered by syzbot, who connected a pppoe socket to a
gre device which had dev->header_ops->create == ipgre_header and
dev->hard_header_len == 0. Therefore, PPPoE didn't reserve any
headroom, and dev_hard_header() crashed when ipgre_header() tried to
prepend its header to skb->data.
skbuff: skb_under_panic: text:000000001d390b3a len:31 put:24
head:00000000d8ed776f data:000000008150e823 tail:0x7 end:0xc0 dev:gre0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 3670 Comm: syzkaller801466 Not tainted
4.15.0-rc7-next-20180115+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:skb_panic+0x162/0x1f0 net/core/skbuff.c:100
RSP: 0018:ffff8801d9bd7840 EFLAGS: 00010282
RAX: 0000000000000083 RBX: ffff8801d4f083c0 RCX: 0000000000000000
RDX: 0000000000000083 RSI: 1ffff1003b37ae92 RDI: ffffed003b37aefc
RBP: ffff8801d9bd78a8 R08: 1ffff1003b37ae8a R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff86200de0
R13: ffffffff84a981ad R14: 0000000000000018 R15: ffff8801d2d34180
FS: 00000000019c4880(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000208bc000 CR3: 00000001d9111001 CR4: 00000000001606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
skb_under_panic net/core/skbuff.c:114 [inline]
skb_push+0xce/0xf0 net/core/skbuff.c:1714
ipgre_header+0x6d/0x4e0 net/ipv4/ip_gre.c:879
dev_hard_header include/linux/netdevice.h:2723 [inline]
pppoe_sendmsg+0x58e/0x8b0 drivers/net/ppp/pppoe.c:890
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:640
sock_write_iter+0x31a/0x5d0 net/socket.c:909
call_write_iter include/linux/fs.h:1775 [inline]
do_iter_readv_writev+0x525/0x7f0 fs/read_write.c:653
do_iter_write+0x154/0x540 fs/read_write.c:932
vfs_writev+0x18a/0x340 fs/read_write.c:977
do_writev+0xfc/0x2a0 fs/read_write.c:1012
SYSC_writev fs/read_write.c:1085 [inline]
SyS_writev+0x27/0x30 fs/read_write.c:1082
entry_SYSCALL_64_fastpath+0x29/0xa0
Admittedly PPPoE shouldn't be allowed to run on non Ethernet-like
interfaces, but reserving space for ->needed_headroom is a more
fundamental issue that needs to be addressed first.
Same problem exists for __pppoe_xmit(), which also needs to take
dev->needed_headroom into account in skb_cow_head().
Fixes: f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom")
Reported-by: syzbot+ed0838d0fa4c4f2b528e20286e6dc63effc7c14d@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1e19c4d689dc1e95bafd23ef68fbc0c6b9e05180 ]
Sukumar reported that sends to the local broadcast address
(255.255.255.255) are broken. Check for the address in vrf driver
and do not redirect to the VRF device - similar to multicast
packets.
With this change sockets can use SO_BINDTODEVICE to specify an
egress interface and receive responses. Note: the egress interface
can not be a VRF device but needs to be the enslaved device.
https://bugzilla.kernel.org/show_bug.cgi?id=198521
Reported-by: Sukumar Gopalakrishnan <sukumarg1973@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a5b1379afbfabf91e3a689e82ac619a7157336b3 ]
Fix initialize the uninitialized tx_qlen to an appropriate value when USB
Full Speed is used.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17b11b76b87afe9f8be199d7a5f442497133e2b0 upstream.
When saving BOs in the hang state we skip one entry of the
kernel_state->bo[] array, thus leaving it to NULL. This leads to a NULL
pointer dereference when, later in this function, we iterate over all
BOs to check their ->madv state.
Fixes: ca26d28bbaa3 ("drm/vc4: improve throughput by pipelining binning and rendering jobs")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180118145821.22344-1-boris.brezillon@free-electrons.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a924d71794c530e55e73d0ce2cc77233307eaa9 upstream.
The newer trackpoints from ALPS, Elan and NXP implement a very limited
subset of extended commands and controls that the original trackpoints
implemented, so we should not be exposing not working controls in sysfs.
The newer trackpoints also do not implement "Power On Reset" or "Read
Extended Button Status", so we should not be using these commands during
initialization.
While we are at it, let's change "unsigned char" to u8 for byte data or
bool for booleans and use better suited error codes instead of -1.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5d07b9e98022d50720e38aa936fc11c67868ece upstream.
Lenovo introduced trackpoint compatible sticks with minimum PS/2 commands.
They supposed to reply with 0x02, 0x03, or 0x04 in response to the
"Read Extended ID" command, so we would know not to try certain extended
commands. Unfortunately even some trackpoints reporting the original IBM
version (0x01 firmware 0x0e) now respond with incorrect data to the "Get
Extended Buttons" command:
thinkpad_acpi: ThinkPad BIOS R0DET87W (1.87 ), EC unknown
thinkpad_acpi: Lenovo ThinkPad E470, model 20H1004SGE
psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 0/0
Since there are no trackpoints without buttons, let's assume the trackpoint
has 3 buttons when we get 0 response to the extended buttons query.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196253
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e5c9c6a885fad00aa559b49d8fc23a60e290824e upstream.
Adds support for the current lineup of Xbox One controllers from PDP
(Performance Designed Products). These controllers are very picky with
their initialization sequence and require an additional 2 packets before
they send any input reports.
Signed-off-by: Mark Furneaux <mark@furneaux.ca>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e749aca84b10f3987b2ee1f76e0c7d8aacc5653c upstream.
Short fragmented packets may never be sent by the hardware when padding
is disabled. This patch stop modifying the GMAC padding bits, to leave
them to their reset value (disabled).
Fixes: 3919357fb0bb ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3cc2e57c4beabcbbaa46e1ac6d77ca8276a4a42d upstream.
Fix to return error code -ENOMEM from the mempool_create_kmalloc_pool()
error handling case instead of 0, as done elsewhere in this function.
Fixes: ef43aa38063a6 ("dm crypt: add cryptographic data integrity protection (authenticated encryption)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc94902bde1e158cd19c4deab208e5d6eb382a44 upstream.
Loading key via kernel keyring service erases the internal
key copy immediately after we pass it in crypto layer. This is
wrong because IV is initialized later and we use wrong key
for the initialization (instead of real key there's just zeroed
block).
The bug may cause data corruption if key is loaded via kernel keyring
service first and later same crypt device is reactivated using exactly
same key in hexbyte representation, or vice versa. The bug (and fix)
affects only ciphers using following IVs: essiv, lmk and tcw.
Fixes: c538f6ec9f56 ("dm crypt: add ability to use keys from the kernel key retention service")
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Reviewed-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 27c7003697fc2c78f965984aa224ef26cd6b2949 upstream.
If dm-crypt uses authenticated mode with separate MAC, there are two
concatenated part of the key structure - key(s) for encryption and
authentication key.
Add a missing check for authenticated key length. If this key length is
smaller than actually provided key, dm-crypt now properly fails instead
of crashing.
Fixes: ef43aa3806 ("dm crypt: add cryptographic data integrity protection (authenticated encryption)")
Reported-by: Salah Coronya <salahx@yahoo.com>
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 717f4b1c52135f279112df82583e0c77e80f90de upstream.
Some asynchronous cipher implementations may use DMA. The stack may
be mapped in the vmalloc area that doesn't support DMA. Therefore,
the cipher request and initialization vector shouldn't be on the
stack.
Fix this by allocating the request and iv with kmalloc.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 490ae017f54e55bde382d45ea24bddfb6d1a0aaf upstream.
For btree removal, there is a corner case that a single thread
could takes 6 locks which is more than THIN_MAX_CONCURRENT_LOCKS(5)
and leads to deadlock.
A btree removal might eventually call
rebalance_children()->rebalance3() to rebalance entries of three
neighbor child nodes when shadow_spine has already acquired two
write locks. In rebalance3(), it tries to shadow and acquire the
write locks of all three child nodes. However, shadowing a child
node requires acquiring a read lock of the original child node and
a write lock of the new block. Although the read lock will be
released after block shadowing, shadowing the third child node
in rebalance3() could still take the sixth lock.
(2 write locks for shadow_spine +
2 write locks for the first two child nodes's shadow +
1 write lock for the last child node's shadow +
1 read lock for the last child node)
Signed-off-by: Dennis Yang <dennisyang@qnap.com>
Acked-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc68d0a43560e950850fc69b58f0f8254b28f6d6 upstream.
When inserting a new key/value pair into a btree we walk down the spine of
btree nodes performing the following 2 operations:
i) space for a new entry
ii) adjusting the first key entry if the new key is lower than any in the node.
If the _root_ node is full, the function btree_split_beneath() allocates 2 new
nodes, and redistibutes the root nodes entries between them. The root node is
left with 2 entries corresponding to the 2 new nodes.
btree_split_beneath() then adjusts the spine to point to one of the two new
children. This means the first key is never adjusted if the new key was lower,
ie. operation (ii) gets missed out. This can result in the new key being
'lost' for a period; until another low valued key is inserted that will uncover
it.
This is a serious bug, and quite hard to make trigger in normal use. A
reproducing test case ("thin create devices-in-reverse-order") is
available as part of the thin-provision-tools project:
https://github.com/jthornber/thin-provisioning-tools/blob/master/functional-tests/device-mapper/dm-tests.scm#L593
Fix the issue by changing btree_split_beneath() so it no longer adjusts
the spine. Instead it unlocks both the new nodes, and lets the main
loop in btree_insert_raw() relock the appropriate one and make any
neccessary adjustments.
Reported-by: Monty Pavel <monty_pavel@sina.com>
Signed-off-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a510a5c75261ba0ec39155326982aa786541e29 upstream.
It looks like in all cases 'struct vmw_connector_state' is used. But
only in stdu connectors, was atomic_{duplicate,destroy}_state() properly
subclassed. Leading to writes beyond the end of the allocated connector
state block and all sorts of fun memory corruption related crashes.
Fixes: d7721ca71126 "drm/vmwgfx: Connector atomic state"
Signed-off-by: Rob Clark <rclark@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c9f926000fe3b84135a81602a9f7e63a6a7898e2 upstream.
Handling CD-ROM devices from libsas is decidedly odd, as libata relies
on SCSI EH to be started to figure out that no medium is present. So we
cannot do asynchronous aborts for SATA devices.
Fixes: 909657615d9 ("scsi: libsas: allow async aborts")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Yves-Alexis Perez <corsac@debian.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db5ff909798ef0099004ad50a0ff5fde92426fd1 upstream.
LITEON EP1 has the same timeout issues as CX1 series devices.
Revert max_sectors to the value of 1024.
Fixes: e0edc8c54646 ("libata: apply MAX_SEC_1024 to all CX1-JB*-HP devices")
Signed-off-by: Xinyu Lin <xinyu0123@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89c6efa61f5709327ecfa24bff18e57a4e80c7fa upstream.
On a I2C_SMBUS_I2C_BLOCK_DATA read request, if data->block[0] is
greater than I2C_SMBUS_BLOCK_MAX + 1, the underlying I2C driver writes
data out of the msgbuf1 array boundary.
It is possible from a user application to run into that issue by
calling the I2C_SMBUS ioctl with data.block[0] greater than
I2C_SMBUS_BLOCK_MAX + 1.
This patch makes the code compliant with
Documentation/i2c/dev-interface by raising an error when the requested
size is larger than 32 bytes.
Call Trace:
[<ffffffff8139f695>] dump_stack+0x67/0x92
[<ffffffff811802a4>] panic+0xc5/0x1eb
[<ffffffff810ecb5f>] ? vprintk_default+0x1f/0x30
[<ffffffff817456d3>] ? i2cdev_ioctl_smbus+0x303/0x320
[<ffffffff8109a68b>] __stack_chk_fail+0x1b/0x20
[<ffffffff817456d3>] i2cdev_ioctl_smbus+0x303/0x320
[<ffffffff81745aed>] i2cdev_ioctl+0x4d/0x1e0
[<ffffffff811f761a>] do_vfs_ioctl+0x2ba/0x490
[<ffffffff81336e43>] ? security_file_ioctl+0x43/0x60
[<ffffffff811f7869>] SyS_ioctl+0x79/0x90
[<ffffffff81a22e97>] entry_SYSCALL_64_fastpath+0x12/0x6a
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8a243af1a68395e07ac85384a2740d4134c67f4 upstream.
In some rare conditions when running one PEAK USB-FD interface over
a non high-speed USB controller, one useless USB fragment might be sent.
This patch fixes the way a USB command is fragmented when its length is
greater than 64 bytes and when the underlying USB controller is not a
high-speed one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7563e2796f8b23c98afcfea7363194227fa089d upstream.
Stefan Wahren reports a problem with a warning fix that was merged
for v4.15: we had lots of device nodes with a 'phys' property pointing
to a device node that is not compliant with the binding documented in
Documentation/devicetree/bindings/phy/phy-bindings.txt
This generally works because USB HCD drivers that support both the generic
phy subsystem and the older usb-phy subsystem ignore most errors from
phy_get() and related calls and then use the usb-phy driver instead.
However, it turns out that making the usb-nop-xceiv device compatible with
the generic-phy binding changes the phy_get() return code from -EINVAL to
-EPROBE_DEFER, and the dwc2 usb controller driver for bcm2835 now returns
-EPROBE_DEFER from its probe function rather than ignoring the failure,
breaking all USB support on raspberry-pi when CONFIG_GENERIC_PHY is
enabled. The same code is used in the dwc3 driver and the usb_add_hcd()
function, so a reasonable assumption would be that many other platforms
are affected as well.
I have reviewed all the related patches and concluded that "usb-nop-xceiv"
is the only USB phy that is affected by the change, and since it is by far
the most commonly referenced phy, all the other USB phy drivers appear
to be used in ways that are are either safe in DT (they don't use the
'phys' property), or in the driver (they already ignore -EPROBE_DEFER
from generic-phy when usb-phy is available).
To work around the problem, this adds a special case to _of_phy_get()
so we ignore any PHY node that is compatible with "usb-nop-xceiv",
as we know that this can never load no matter how much we defer. In the
future, we might implement a generic-phy driver for "usb-nop-xceiv"
and then remove this workaround.
Since we generally want older kernels to also want to work with the
fixed devicetree files, it would be good to backport the patch into
stable kernels as well (3.13+ are possibly affected), even though they
don't contain any of the patches that may have caused regressions.
Fixes: 014d6da6cb25 ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Fixes: c5bbf358b790 arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
Fixes: 44e5dced2ef6 arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
Fixes: f568f6f554b8 ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
Fixes: d745d5f277bf ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
Fixes: 915fbe59cbf2 ARM: dts: imx: Add missing #phy-cells to usb-nop-xceiv
Link: https://marc.info/?l=linux-usb&m=151518314314753&w=2
Link: https://patchwork.kernel.org/patch/10158145/
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5b189201993ab03001a398de731045bfea90c689 upstream.
A helper purported to look up a child node based on its name was using
the wrong of-helper and ended up prematurely freeing the parent of-node
while searching the whole device tree depth-first starting at the parent
node.
Fixes: 64b9e4d803b1 ("input: twl4030-vibra: Support for DT booted kernel")
Fixes: e661d0a04462 ("Input: twl4030-vibra - fix ERROR: Bad of_node_put() warning")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcaf12a8b0bbdbfcfa2be8dff2c4948d9844b4ad upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
Later sanity checks on node properties (which would likely be missing)
should prevent this from causing much trouble however, especially as the
original premature free of the parent node has already been fixed
separately (but that "fix" was apparently never backported to stable).
Fixes: e7ec014a47e4 ("Input: twl6040-vibra - update for device tree support")
Fixes: c52c545ead97 ("Input: twl6040-vibra - fix DT node memory management")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com> (on Pyra OMAP5 hardware)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 906bf7daa0618d0ef39f4872ca42218c29a3631f upstream.
Fix child node-lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
To make things worse, the parent node was prematurely freed, while the
child node was leaked.
Fixes: 2e57d56747e6 ("mfd: 88pm860x: Device tree support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 55edde9fff1ae4114c893c572e641620c76c9c21 upstream.
KASAN found a UAF due to dangling pointer. As the report below says,
rmi_f11_attention() accesses drvdata->attn_data.data, which was freed in
rmi_irq_fn.
[ 311.424062] BUG: KASAN: use-after-free in rmi_f11_attention+0x526/0x5e0 [rmi_core]
[ 311.424067] Read of size 27 at addr ffff88041fd610db by task irq/131-i2c_hid/1162
[ 311.424075] CPU: 0 PID: 1162 Comm: irq/131-i2c_hid Not tainted 4.15.0-rc8+ #2
[ 311.424076] Hardware name: Razer Blade Stealth/Razer, BIOS 6.05 01/26/2017
[ 311.424078] Call Trace:
[ 311.424086] dump_stack+0xae/0x12d
[ 311.424090] ? _atomic_dec_and_lock+0x103/0x103
[ 311.424094] ? show_regs_print_info+0xa/0xa
[ 311.424099] ? input_handle_event+0x10b/0x810
[ 311.424104] print_address_description+0x65/0x229
[ 311.424108] kasan_report.cold.5+0xa7/0x281
[ 311.424117] rmi_f11_attention+0x526/0x5e0 [rmi_core]
[ 311.424123] ? memcpy+0x1f/0x50
[ 311.424132] ? rmi_f11_attention+0x526/0x5e0 [rmi_core]
[ 311.424143] ? rmi_f11_probe+0x1e20/0x1e20 [rmi_core]
[ 311.424153] ? rmi_process_interrupt_requests+0x220/0x2a0 [rmi_core]
[ 311.424163] ? rmi_irq_fn+0x22c/0x270 [rmi_core]
[ 311.424173] ? rmi_process_interrupt_requests+0x2a0/0x2a0 [rmi_core]
[ 311.424177] ? free_irq+0xa0/0xa0
[ 311.424180] ? irq_finalize_oneshot.part.39+0xeb/0x180
[ 311.424190] ? rmi_process_interrupt_requests+0x2a0/0x2a0 [rmi_core]
[ 311.424193] ? irq_thread_fn+0x3d/0x80
[ 311.424197] ? irq_finalize_oneshot.part.39+0x180/0x180
[ 311.424200] ? irq_thread+0x21d/0x290
[ 311.424203] ? irq_thread_check_affinity+0x170/0x170
[ 311.424207] ? remove_wait_queue+0x150/0x150
[ 311.424212] ? kasan_unpoison_shadow+0x30/0x40
[ 311.424214] ? __init_waitqueue_head+0xa0/0xd0
[ 311.424218] ? task_non_contending.cold.55+0x18/0x18
[ 311.424221] ? irq_forced_thread_fn+0xa0/0xa0
[ 311.424226] ? irq_thread_check_affinity+0x170/0x170
[ 311.424230] ? kthread+0x19e/0x1c0
[ 311.424233] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 311.424237] ? ret_from_fork+0x32/0x40
[ 311.424244] Allocated by task 899:
[ 311.424249] kasan_kmalloc+0xbf/0xe0
[ 311.424252] __kmalloc_track_caller+0xd9/0x1f0
[ 311.424255] kmemdup+0x17/0x40
[ 311.424264] rmi_set_attn_data+0xa4/0x1b0 [rmi_core]
[ 311.424269] rmi_raw_event+0x10b/0x1f0 [hid_rmi]
[ 311.424278] hid_input_report+0x1a8/0x2c0 [hid]
[ 311.424283] i2c_hid_irq+0x146/0x1d0 [i2c_hid]
[ 311.424286] irq_thread_fn+0x3d/0x80
[ 311.424288] irq_thread+0x21d/0x290
[ 311.424291] kthread+0x19e/0x1c0
[ 311.424293] ret_from_fork+0x32/0x40
[ 311.424296] Freed by task 1162:
[ 311.424300] kasan_slab_free+0x71/0xc0
[ 311.424303] kfree+0x90/0x190
[ 311.424311] rmi_irq_fn+0x1b2/0x270 [rmi_core]
[ 311.424319] rmi_irq_fn+0x257/0x270 [rmi_core]
[ 311.424322] irq_thread_fn+0x3d/0x80
[ 311.424324] irq_thread+0x21d/0x290
[ 311.424327] kthread+0x19e/0x1c0
[ 311.424330] ret_from_fork+0x32/0x40
[ 311.424334] The buggy address belongs to the object at ffff88041fd610c0 which belongs to the cache kmalloc-64 of size 64
[ 311.424340] The buggy address is located 27 bytes inside of 64-byte region [ffff88041fd610c0, ffff88041fd61100)
[ 311.424344] The buggy address belongs to the page:
[ 311.424348] page:ffffea00107f5840 count:1 mapcount:0 mapping: (null) index:0x0
[ 311.424353] flags: 0x17ffffc0000100(slab)
[ 311.424358] raw: 0017ffffc0000100 0000000000000000 0000000000000000 00000001802a002a
[ 311.424363] raw: dead000000000100 dead000000000200 ffff8804228036c0 0000000000000000
[ 311.424366] page dumped because: kasan: bad access detected
[ 311.424369] Memory state around the buggy address:
[ 311.424373] ffff88041fd60f80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 311.424377] ffff88041fd61000: fb fb fb fb fb fb fb fb fc fc fc fc fb fb fb fb
[ 311.424381] >ffff88041fd61080: fb fb fb fb fc fc fc fc fb fb fb fb fb fb fb fb
[ 311.424384] ^
[ 311.424387] ffff88041fd61100: fc fc fc fc fb fb fb fb fb fb fb fb fc fc fc fc
[ 311.424391] ffff88041fd61180: fb fb fb fb fb fb fb fb fc fc fc fc fb fb fb fb
Signed-off-by: Nick Desaulniers <nick.desaulniers@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d94e776bd29670f01befa27e12df784fa05fa2e upstream.
The fix for handling two-finger scroll (i4a646580f793 - "Input: ALPS -
fix two-finger scroll breakage in right side on ALPS touchpad")
introduced a minor "typo" that broke decoding of multi-touch events are
decoded on some ALPS touchpads. For example, tapping with three-fingers
can no longer be used to emulate middle-mouse-button (the kernel doesn't
recognize this as the proper event, and doesn't report it correctly to
userspace). This affects touchpads that use SS4 "plus" protocol
variant, like those found on Dell E7270 & E7470 laptops (tested on
E7270).
First, probably the code in alps_decode_ss4_v2() for case
SS4_PACKET_ID_MULTI used inconsistent indices to "f->mt[]". You can see
0 & 1 are used for the "if" part but 2 & 3 are used for the "else" part.
Second, in the previous patch, new macros were introduced to decode X
coordinates specific to the SS4 "plus" variant, but the macro to
define the maximum X value wasn't changed accordingly. The macros to
decode X values for "plus" variant are effectively shifted right by 1
bit, but the max wasn't shifted too. This causes the driver to
incorrectly handle "no data" cases, which also interfered with how
multi-touch was handled.
Fixes: 4a646580f793 ("Input: ALPS - fix two-finger scroll breakage...")
Signed-off-by: Nir Perry <nirperry@gmail.com>
Reviewed-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 499ed50f603b4c9834197b2411ba3bd9aaa624d4 upstream.
Commit 5143c953a786 ("mmc: sdhci-esdhc-imx: Allow all supported
prescaler values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR
mode, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value if the i.MX53
eSDHCv3 is detected. According to the i.MX53 reference manual, if
DLLCTRL[10] can be set, then the controller is eSDHCv3, else it is
eSDHCv2.
This commit fixes the following issue, which was preventing the i.MX53
Loco (IMX53QSB) board from booting Linux 4.15.0-rc5:
[ 1.882668] mmcblk1: error -84 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc00
[ 2.002255] mmcblk1: error -84 transferring data, sector 2050, nr 6, cmd response 0x900, card status 0xc00
[ 12.645056] mmc1: Timeout waiting for hardware interrupt.
[ 12.650473] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 12.656921] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001201
[ 12.663366] mmc1: sdhci: Blk size: 0x00000004 | Blk cnt: 0x00000000
[ 12.669813] mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
[ 12.676258] mmc1: sdhci: Present: 0x01f8028f | Host ctl: 0x00000013
[ 12.682703] mmc1: sdhci: Power: 0x00000002 | Blk gap: 0x00000000
[ 12.689148] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000003f
[ 12.695594] mmc1: sdhci: Timeout: 0x0000008e | Int stat: 0x00000000
[ 12.702039] mmc1: sdhci: Int enab: 0x107f004b | Sig enab: 0x107f004b
[ 12.708485] mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00001201
[ 12.714930] mmc1: sdhci: Caps: 0x07eb0000 | Caps_1: 0x08100810
[ 12.721375] mmc1: sdhci: Cmd: 0x0000163a | Max curr: 0x00000000
[ 12.727821] mmc1: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x00000000
[ 12.734265] mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 12.740709] mmc1: sdhci: Host ctl2: 0x00000000
[ 12.745157] mmc1: sdhci: ADMA Err: 0x00000001 | ADMA Ptr: 0xc8049200
[ 12.751601] mmc1: sdhci: ============================================
[ 12.758110] print_req_error: I/O error, dev mmcblk1, sector 2050
[ 12.764135] Buffer I/O error on dev mmcblk1p1, logical block 0, lost sync page write
[ 12.775163] EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
[ 12.782746] VFS: Mounted root (ext4 filesystem) on device 179:9.
[ 12.789151] mmcblk1: response CRC error sending SET_BLOCK_COUNT command, card status 0x900
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reported-by: Wladimir J. van der Laan <laanwj@gmail.com>
Tested-by: Wladimir J. van der Laan <laanwj@gmail.com>
Fixes: 5143c953a786 ("mmc: sdhci-esdhc-imx: Allow all supported prescaler values")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd52cb26e7ead5093635e98e07e221e4df482d34 upstream.
In case we fail to establish the connection we must drain our pre-posted
login recieve work request before continuing safely with connection
teardown.
Fixes: a060b5629ab0 ("IB/core: generic RDMA READ/WRITE API")
Reported-by: Amrani, Ram <Ram.Amrani@cavium.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae59c3f0b6cfd472fed96e50548a799b8971d876 upstream.
The rdma_ah_find_type() accesses the port array based on an index
controlled by userspace. The existing bounds check is after the first use
of the index, so userspace can generate an out of bounds access, as shown
by the KASN report below.
==================================================================
BUG: KASAN: slab-out-of-bounds in to_rdma_ah_attr+0xa8/0x3b0
Read of size 4 at addr ffff880019ae2268 by task ibv_rc_pingpong/409
CPU: 0 PID: 409 Comm: ibv_rc_pingpong Not tainted 4.15.0-rc2-00031-gb60a3faf5b83-dirty #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
Call Trace:
dump_stack+0xe9/0x18f
print_address_description+0xa2/0x350
kasan_report+0x3a5/0x400
to_rdma_ah_attr+0xa8/0x3b0
mlx5_ib_query_qp+0xd35/0x1330
ib_query_qp+0x8a/0xb0
ib_uverbs_query_qp+0x237/0x7f0
ib_uverbs_write+0x617/0xd80
__vfs_write+0xf7/0x500
vfs_write+0x149/0x310
SyS_write+0xca/0x190
entry_SYSCALL_64_fastpath+0x18/0x85
RIP: 0033:0x7fe9c7a275a0
RSP: 002b:00007ffee5498738 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007fe9c7ce4b00 RCX: 00007fe9c7a275a0
RDX: 0000000000000018 RSI: 00007ffee5498800 RDI: 0000000000000003
RBP: 000055d0c8d3f010 R08: 00007ffee5498800 R09: 0000000000000018
R10: 00000000000000ba R11: 0000000000000246 R12: 0000000000008000
R13: 0000000000004fb0 R14: 000055d0c8d3f050 R15: 00007ffee5498560
Allocated by task 1:
__kmalloc+0x3f9/0x430
alloc_mad_private+0x25/0x50
ib_mad_post_receive_mads+0x204/0xa60
ib_mad_init_device+0xa59/0x1020
ib_register_device+0x83a/0xbc0
mlx5_ib_add+0x50e/0x5c0
mlx5_add_device+0x142/0x410
mlx5_register_interface+0x18f/0x210
mlx5_ib_init+0x56/0x63
do_one_initcall+0x15b/0x270
kernel_init_freeable+0x2d8/0x3d0
kernel_init+0x14/0x190
ret_from_fork+0x24/0x30
Freed by task 0:
(stack is not available)
The buggy address belongs to the object at ffff880019ae2000
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 104 bytes to the right of
512-byte region [ffff880019ae2000, ffff880019ae2200)
The buggy address belongs to the page:
page:000000005d674e18 count:1 mapcount:0 mapping: (null) index:0x0 compound_mapcount: 0
flags: 0x4000000000008100(slab|head)
raw: 4000000000008100 0000000000000000 0000000000000000 00000001000c000c
raw: dead000000000100 dead000000000200 ffff88001a402000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff880019ae2100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff880019ae2180: 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc
>ffff880019ae2200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff880019ae2280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff880019ae2300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
Disabling lock debugging due to kernel taint
Fixes: 44c58487d51a ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 57194fa763bfa1a0908f30d4c77835beaa118fcb upstream.
In the original code, we set "fd->uctxt" to NULL and then dereference it
which will cause an Oops.
Fixes: f2a3bc00a03c ("IB/hfi1: Protect context array set/clear with spinlock")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b5c7ef3d0d0610bda9b63263f7c5b7178d11015 upstream.
Fixes broken dp on GF119:
Call Trace:
? nvkm_dp_train_drive+0x183/0x2c0 [nouveau]
nvkm_dp_acquire+0x4f3/0xcd0 [nouveau]
nv50_disp_super_2_2+0x5d/0x470 [nouveau]
? nvkm_devinit_pll_set+0xf/0x20 [nouveau]
gf119_disp_super+0x19c/0x2f0 [nouveau]
process_one_work+0x193/0x3c0
worker_thread+0x35/0x3b0
kthread+0x125/0x140
? process_one_work+0x3c0/0x3c0
? kthread_park+0x60/0x60
ret_from_fork+0x25/0x30
Code: Bad RIP value.
RIP: (null) RSP: ffffb1e243e4bc38
CR2: 0000000000000000
Fixes: af85389c614a drm/nouveau/disp: shuffle functions around
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103421
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 87590ce6e373d1a5401f6539f0c59ef92dd924a9 upstream.
As the meltdown/spectre problem affects several CPU architectures, it makes
sense to have common way to express whether a system is affected by a
particular vulnerability or not. If affected the way to express the
mitigation should be common as well.
Create /sys/devices/system/cpu/vulnerabilities folder and files for
meltdown, spectre_v1 and spectre_v2.
Allow architectures to override the show function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180107214913.096657732@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4110e02eb45ea447ec6f5459c9934de0a273fb91 upstream.
e1000e_check_for_copper_link() and e1000_check_for_copper_link_ich8lan()
are the two functions that may be assigned to mac.ops.check_for_link when
phy.media_type == e1000_media_type_copper. Commit 19110cfbb34d ("e1000e:
Separate signaling for link check/link up") changed the meaning of the
return value of check_for_link for copper media but only adjusted the first
function. This patch adjusts the second function likewise.
Reported-by: Christian Hesse <list@eworm.de>
Reported-by: Gabriel C <nix.or.die@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198047
Fixes: 19110cfbb34d ("e1000e: Separate signaling for link check/link up")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Christian Hesse <list@eworm.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa1f10e85b0ab53dee85d8e293c8159d18d293a8 upstream.
class_find_device already does a get_device on the returned device.
So the device returned by of_find_mux_chip_by_node is already referenced
and we should not reference it again (and unref it on error).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 928afc85270753657b5543e052cc270c279a3fe9 upstream.
The UAS mode of Norelsys NS1068(X) is reported to fail to work on
several platforms with the following error message:
xhci-hcd xhci-hcd.0.auto: ERROR Transfer event for unknown stream ring slot 1 ep 8
xhci-hcd xhci-hcd.0.auto: @00000000bf04a400 00000000 00000000 1b000000 01098001
And when trying to mount a partition on the disk the disk will
disconnect from the USB controller, then after re-connecting the device
will be offlined and not working at all.
Falling back to USB mass storage can solve this problem, so ignore UAS
function of this chip.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 443064cb0b1fb4569fe0a71209da7625129fb760 upstream.
A lock-unlock is missing in ASHMEM_SET_SIZE ioctl which can result in a
race condition when mmap is called. After the !asma->file check, before
setting asma->size, asma->file can be set in mmap. That would result in
having different asma->size than the mapped memory size. Combined with
ASHMEM_UNPIN ioctl and shrinker invocation, this can result in memory
corruption.
Signed-off-by: Viktor Slavkovic <viktors@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5fd77a3a0e408c23ab4002a57db980e46bc16e72 upstream.
v_send_ret_submit() handles urb with a null transfer_buffer, when it
replays a packet with potential malicious data that could contain a
null buffer.
Add a check for the condition when actual_length > 0 and transfer_buffer
is null.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b78d830f0049ef1966dc1e0ebd1ec2a594e2cf25 upstream.
Harden CMD_SUBMIT path to handle malicious input that could trigger
large memory allocations. Add checks to validate transfer_buffer_length
and number_of_packets to protect against bad input requesting for
unbounded memory allocations.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e1346fd87c71a1f61de1fe476ec8df1425ac931c upstream.
usbip_dump_usb_device() and usbip_dump_urb() print kernel addresses.
Remove kernel addresses from usb device and urb debug msgs and improve
the message content.
Instead of printing parent device and bus addresses, print parent device
and bus names.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ae2c3c280db183ca9ada2675c34ec2f7378abfa upstream.
The error-handling pathways in usb_add_gadget_udc_release() are messed
up. Aside from the uninformative statement labels, they can deallocate
the udc structure after calling put_device(), which is a double-free.
This was observed by KASAN in automatic testing.
This patch cleans up the routine. It preserves the requirement that
when any failure occurs, we call put_device(&gadget->dev).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 46eb14a6e1585d99c1b9f58d0e7389082a5f466b upstream.
Automated tests triggered this by opening usbmon and accessing the
mmap while simultaneously resizing the buffers. This bug was with
us since 2006, because typically applications only size the buffers
once and thus avoid racing. Reported by Kirill A. Shutemov.
Reported-by: <syzbot+f9831b881b3e849829fc@syzkaller.appspotmail.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b8626f1dc29d3eee444bfaa92146ec7b291ef41c upstream.
When using a GPIO which is high by default, and initialize the
driver in USB Hub mode, initialization fails with:
[ 111.757794] usb3503 0-0008: SP_ILOCK failed (-5)
The reason seems to be that the chip is not properly reset.
Probe does initialize reset low, however some lines later the
code already set it back high, which is not long enouth.
Make sure reset is asserted for at least 100us by inserting a
delay after initializing the reset pin during probe.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
