| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 10545937e866ccdbb7ab583031dbdcc6b14e4eb4 ]
On IOMMU systems DMA mapping can fail, we need to check for
that possibility.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dfa5bb622555d9da0df21b50f46ebdeef390041b upstream.
The ondemand governor calculates load in terms of frequency and
increases it only if load_freq is greater than up_threshold
multiplied by the current or average frequency. This appears to
produce oscillations of frequency between min and max because,
for example, a relatively small load can easily saturate minimum
frequency and lead the CPU to the max. Then, it will decrease
back to the min due to small load_freq.
Change the calculation method of load and target frequency on the
basis of the following two observations:
- Load computation should not depend on the current or average
measured frequency. For example, absolute load of 80% at 100MHz
is not necessarily equivalent to 8% at 1000MHz in the next
sampling interval.
- It should be possible to increase the target frequency to any
value present in the frequency table proportional to the absolute
load, rather than to the max only, so that:
Target frequency = C * load
where we take C = policy->cpuinfo.max_freq / 100.
Tested on Intel i7-3770 CPU @ 3.40GHz and on Quad core 1500MHz Krait.
Phoronix benchmark of Linux Kernel Compilation 3.1 test shows an
increase ~1.5% in performance. cpufreq_stats (time_in_state) shows
that middle frequencies are used more, with this patch. Highest
and lowest frequencies were used less by ~9%.
[rjw: We have run multiple other tests on kernels with this
change applied and in the vast majority of cases it turns out
that the resulting performance improvement also leads to reduced
consumption of energy. The change is additionally justified by
the overall simplification of the code in question.]
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a857c0b9e24e39fe5be82451b65377795f9538d8 upstream.
The time spent by a CPU under a given frequency is stored in jiffies unit
in the cpu var cpufreq_stats_table->time_in_state[i], i being the index of
the frequency.
This is what is displayed in the following file on the right column:
cat /sys/devices/system/cpu/cpuX/cpufreq/stats/time_in_state
2301000 19835820
2300000 3172
[...]
Now cpufreq converts this jiffies unit delta to clock_t before returning it
to the user as in the above file. And that conversion is achieved using the API
cputime64_to_clock_t().
Although it accidentally works on traditional tick based cputime accounting, where
cputime_t maps directly to jiffies, it doesn't work with other types of cputime
accounting such as CONFIG_VIRT_CPU_ACCOUNTING_* where cputime_t can map to nsecs
or any granularity preffered by the architecture.
For example we get a buggy zero delta on full dyntick configurations:
cat /sys/devices/system/cpu/cpuX/cpufreq/stats/time_in_state
2301000 0
2300000 0
[...]
Fix this with using the proper jiffies_64_t to clock_t conversion.
Reported-and-tested-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bbc1c5e8ad6dfebf9d13b8a4ccdf66c92913eac9 upstream.
Since linux kernel 3.13, kthread_run() internally uses
wait_for_completion_killable(). We sometimes may use kthread_run()
while we still have a signal pending, which we used to kick our threads
out of potentially blocking network functions, causing kthread_run() to
mistake that as a new fatal signal and fail.
Fix: flush_signals() before kthread_run().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e0e99ba64c7ba46133a7c8a3e3f7de01f23bd93 upstream.
It has come to my attention (thanks Martin) that 'discard_zeroes_data'
is only a hint. Some devices in some cases don't do what it
says on the label.
The use of DISCARD in RAID5 depends on reads from discarded regions
being predictably zero. If a write to a previously discarded region
performs a read-modify-write cycle it assumes that the parity block
was consistent with the data blocks. If all were zero, this would
be the case. If some are and some aren't this would not be the case.
This could lead to data corruption after a device failure when
data needs to be reconstructed from the parity.
As we cannot trust 'discard_zeroes_data', ignore it by default
and so disallow DISCARD on all raid4/5/6 arrays.
As many devices are trustworthy, and as there are benefits to using
DISCARD, add a module parameter to over-ride this caution and cause
DISCARD to work if discard_zeroes_data is set.
If a site want to enable DISCARD on some arrays but not on others they
should select DISCARD support at the filesystem level, and set the
raid456 module parameter.
raid456.devices_handle_discard_safely=Y
As this is a data-safety issue, I believe this patch is suitable for
-stable.
DISCARD support for RAID456 was added in 3.7
Cc: Shaohua Li <shli@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Heinz Mauelshagen <heinzm@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Fixes: 620125f2bf8ff0c4969b79653b54d7bcc9d40637
Signed-off-by: NeilBrown <neilb@suse.de>
[bwh: Backported to 3.10: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58d75f4b1ce26324b4d809b18f94819843a98731 upstream.
The recent conversion of saa7134 to vb2 unconvered a poll() bug that
broke the teletext applications alevt and mtt. These applications
expect that calling poll() without having called VIDIOC_STREAMON will
cause poll() to return POLLERR. That did not happen in vb2.
This patch fixes that behavior. It also fixes what should happen when
poll() is called when STREAMON is called but no buffers have been
queued. In that case poll() will also return POLLERR, but only for
capture queues since output queues will always return POLLOUT
anyway in that situation.
This brings the vb2 behavior in line with the old videobuf behavior.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4089a332883ad969700aac5dd4dd5f1c4fee825 upstream.
Using dma_mapping_error() to make sure the mapping did not
fail.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: "Petallo, MauriceX R" <mauricex.r.petallo@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b8cb6b4c121e1bf1963c16ed69e7adcb1bc301cd upstream.
If a devices is being recovered it is not InSync and is not Faulty.
If a read error is experienced on that device, fix_read_error()
will be called, but it ignores non-InSync devices. So it will
neither fix the error nor fail the device.
It is incorrect that fix_read_error() ignores non-InSync devices.
It should only ignore Faulty devices. So fix it.
This became a bug when we allowed reading from a device that was being
recovered. It is suitable for any subsequent -stable kernel.
Fixes: da8840a747c0dbf49506ec906757a6b87b9741e9
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6a03dc92cc2edfa2257502557b9f714893987383 upstream.
This was caused by an uninitialized setup.config field.
Based on a suggestion from Devin Heitmueller.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Reported-by: Scott Robinson <scott.robinson55@gmail.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc99f16f076559235c92d3eb66d03d1310faea08 upstream.
We can't suspend the PHYs before dwc3_core_exit_mode()
has been called, that's because the host and/or device
sides might still need to communicate with the far end
link partner.
Fixes: 8ba007a (usb: dwc3: core: enable the USB2 and USB3 phy in probe)
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fed33afce0eda44a46ae24d93aec1b5198c0bac4 upstream.
Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.
Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.
Fixes: 72246da (usb: Introduce DesignWare USB3 DRD Driver)
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96908589a8b2584b1185f834d365f5cc360e8226 upstream.
Commit 71c731a (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.
That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.
This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.
This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.
This patch should be backported to all kernels containing
commit 71c731a.
Fixes: 71c731a (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware)
Cc: Alexis R. Cortes <alexis.cortes@ti.com>
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c66517165610b911e4c6d268f28d8c640832dbd1 upstream.
The Sitecom WLA-2102 adapter uses this driver.
Reported-by: Nico Baggus <nico-linux@noci.xs4all.nl>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nico Baggus <nico-linux@noci.xs4all.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6cad1376954e591c3c41500c4e586e183e7ffe6d upstream.
This patch adds the IDE mode SATA Device IDs for the Intel 9 Series PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d2682118f4bb3ceb835f91c1a694407a31bb7378 upstream.
The sys_vendor / product_name are somewhat generic unfortunately, so this
may lead to some false positives. But nomux usually does no harm, where as
not having it clearly is causing problems on the Avatar AVIU-145A6.
https://bugzilla.kernel.org/show_bug.cgi?id=77391
Reported-by: Hugo P <saurosii@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cc18a69c92d0972bc2fc5a047ee3be1e8398171b upstream.
https://bugzilla.kernel.org/show_bug.cgi?id=69731
Reported-by: Jason Robinson <mail@jasonrobinson.me>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c01206796139e2b1feb7539bc72174fef1c6dc6e upstream.
We are getting more and more reports about LG laptops not having
functioning keyboard if we try to deactivate keyboard during probe.
Given that having keyboard deactivated is merely "nice to have"
instead of a hard requirement for probing, let's disable it on all
LG boxes instead of trying to hunt down particular models.
This change is prompted by patches trying to add "LG Electronics"/"ROCKY"
and "LG Electronics"/"LW60-F27B" to the DMI list.
https://bugzilla.kernel.org/show_bug.cgi?id=77051
Reported-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Reported-by: Georgios Tsalikis <georgios@tsalikis.net>
Tested-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 271329b3c798b2102120f5df829071c211ef00ed upstream.
Adjust Elantech signature validation to account fo rnewer models of
touchpads.
Reported-and-tested-by: Màrius Monton <marius.monton@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5715fc764f7753d464dbe094b5ef9cffa6e479a4 upstream.
ForcePads are found on HP EliteBook 1040 laptops. They lack any kind of
physical buttons, instead they generate primary button click when user
presses somewhat hard on the surface of the touchpad. Unfortunately they
also report primary button click whenever there are 2 or more contacts
on the pad, messing up all multi-finger gestures (2-finger scrolling,
multi-finger tapping, etc). To cope with this behavior we introduce a
delay (currently 50 msecs) in reporting primary press in case more
contacts appear.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a80d8b02751060a178bb1f7a6b7a93645a7a308b upstream.
When running a 32-bit inputattach utility in a 64-bit system, there will be
error code "inputattach: can't set device type". This is caused by the
serport device driver not supporting compat_ioctl, so that SPIOCSTYPE ioctl
fails.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d49ec52ff6ddcda178fc2476a109cf1bd1fa19ed upstream.
The DM crypt target accesses memory beyond allocated space resulting in
a crash on 32 bit x86 systems.
This bug is very old (it dates back to 2.6.25 commit 3a7f6c990ad04 "dm
crypt: use async crypto"). However, this bug was masked by the fact
that kmalloc rounds the size up to the next power of two. This bug
wasn't exposed until 3.17-rc1 commit 298a9fa08a ("dm crypt: use per-bio
data"). By switching to using per-bio data there was no longer any
padding beyond the end of a dm-crypt allocated memory block.
To minimize allocation overhead dm-crypt puts several structures into one
block allocated with kmalloc. The block holds struct ablkcipher_request,
cipher-specific scratch pad (crypto_ablkcipher_reqsize(any_tfm(cc))),
struct dm_crypt_request and an initialization vector.
The variable dmreq_start is set to offset of struct dm_crypt_request
within this memory block. dm-crypt allocates the block with this size:
cc->dmreq_start + sizeof(struct dm_crypt_request) + cc->iv_size.
When accessing the initialization vector, dm-crypt uses the function
iv_of_dmreq, which performs this calculation: ALIGN((unsigned long)(dmreq
+ 1), crypto_ablkcipher_alignmask(any_tfm(cc)) + 1).
dm-crypt allocated "cc->iv_size" bytes beyond the end of dm_crypt_request
structure. However, when dm-crypt accesses the initialization vector, it
takes a pointer to the end of dm_crypt_request, aligns it, and then uses
it as the initialization vector. If the end of dm_crypt_request is not
aligned on a crypto_ablkcipher_alignmask(any_tfm(cc)) boundary the
alignment causes the initialization vector to point beyond the allocated
space.
Fix this bug by calculating the variable iv_size_padding and adding it
to the allocated size.
Also correct the alignment of dm_crypt_request. struct dm_crypt_request
is specific to dm-crypt (it isn't used by the crypto subsystem at all),
so it is aligned on __alignof__(struct dm_crypt_request).
Also align per_bio_data_size on ARCH_KMALLOC_MINALIGN, so that it is
aligned as if the block was allocated with kmalloc.
Reported-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f47f46d7b09cf1d09e4b44b6cc4dd7d68a08028c upstream.
This reverts commit 43d826ca5979927131685cc2092c7ce862cb91cd.
This commit caused packet loss.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db9bfd64b14a3a8f1868d2164518fdeab1b26ad1 upstream.
This patches fixes a potential buffer overrun in __iscsi_conn_send_pdu.
This function is used by iscsi drivers and userspace to send iscsi PDUs/
commands. For login commands, we have a set buffer size. For all other
commands we do not support data buffers.
This was reported by Dan Carpenter here:
http://www.spinics.net/lists/linux-scsi/msg66838.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d07f1e8600ccb885c8f4143402b8912f7d827bcb upstream.
Smatch says that skb->data is untrusted so we need to check to make sure
that the memcpy() doesn't overflow.
Fixes: cfad1ba87150 ('NFC: Initial support for Inside Secure microread')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b53b0d99d6fbf7d44330395349a895521cfdbc96 upstream.
This patch fixes a bug in iscsit_logout_post_handler_diffcid() where
a pointer used as storage for list_for_each_entry() was incorrectly
being used to determine if no matching entry had been found.
This patch changes iscsit_logout_post_handler_diffcid() to key off
bool conn_found to determine if the function needs to exit early.
Reported-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8ae757d09c45102b347a1bc2867f54ffc1ab8fda upstream.
In iscsi_copy_param_list() a failed iscsi_param_list memory allocation
currently invokes iscsi_release_param_list() to cleanup, and will promptly
trigger a NULL pointer dereference.
Instead, go ahead and return for the first iscsi_copy_param_list()
failure case.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0fc4ea701fcf5bc51ace4e288af5be741465f776 upstream.
disconnected_handler is invoked on several CM events (such
as DISCONNECTED, DEVICE_REMOVAL, TIMEWAIT_EXIT...). Since
multiple events can occur while before isert_free_conn is
invoked, we might put all isert_conn references and free
the connection too early.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c2f88b17a1d97ca4ecd96cc22333a7a4f1407d39 upstream.
In case the connection didn't reach connected state, disconnected
handler will never be invoked thus the second kref_put on
isert_conn will be missing.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 872687f626e033b4ddfaec1e410057cfc6636d77 upstream.
Fixes: a2c12493ed7e ('iio: of_iio_channel_get_by_name() returns non-null pointers for error legs')
which improperly assumes that of_iio_channel_get_by_name must always
return NULL and thus now hides -EPROBE_DEFER.
Signed-off-by: Johannes Pointner <johannes.pointner@br-automation.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a31d0928999fbf33b3a6042e8bcb7b7f7e07d094 upstream.
This patch fix gains values. The first driver was designed using
engineering samples, in mass production the values are changed.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e5846be33277802c0c76e5c12825d0e4d27f639 upstream.
This can result in wrong reference count for trigger device, call
iio_trigger_get to increment reference.
Refer to http://www.spinics.net/lists/linux-iio/msg13669.html for discussion
with Jonathan.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f0e84acd7056e6d7ade551c6439531606ae30a46 upstream.
This can result in wrong reference count for trigger device, call
iio_trigger_get to increment reference.
Refer to http://www.spinics.net/lists/linux-iio/msg13669.html for discussion
with Jonathan.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0495081179212b758775df752e657ea71dcae020 upstream.
This can result in wrong reference count for trigger device, call
iio_trigger_get to increment reference.
Refer to http://www.spinics.net/lists/linux-iio/msg13669.html for discussion
with Jonathan.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b07e3b3850b2e1f09c19f54d3ed7210d9f529e2c upstream.
This can result in wrong reference count for trigger device, call
iio_trigger_get to increment reference.
Refer to http://www.spinics.net/lists/linux-iio/msg13669.html for discussion
with Jonathan.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0b4dce2ee694a991ef38203ec5ff91a738518cb3 upstream.
This can result in wrong reference count for trigger device, call
iio_trigger_get to increment reference.
Refer to http://www.spinics.net/lists/linux-iio/msg13669.html for discussion
with Jonathan.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5844a8b9d98ec11ce1d77610daacf3f0a0e14715 upstream.
A previous over-zealous factorisation of code means that we only treat
registers as volatile if they are readable. For most devices this is fine
since normally most registers can be read and volatility implies
readability but for format_write() devices where there is no readback from
the hardware and we use volatility to mean simply uncacheability this means
that we end up treating all registers as cacheble.
A bigger refactoring of the code to clarify this is in order but as a fix
make a minimal change and only check readability when checking volatility
if there is no format_write() operation defined for the device.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 75ec6e55f1384548311a13ce4fcb39c516053314 upstream.
Changes to correct several GPIO issues:
1) The update_rule in a GPIO field definition is now ignored;
a read-modify-write operation is never performed for GPIO fields.
(Internally, this means that the field assembly/disassembly
code is completely bypassed for GPIO.)
2) The Address parameter passed to a GPIO region handler is
now the bit offset of the field from a previous Connection()
operator. Thus, it becomes a "Pin Number Index" into the
Connection() resource descriptor.
3) The bit_width parameter passed to a GPIO region handler is
now the exact bit width of the GPIO field. Thus, it can be
interpreted as "number of pins".
Overall, we can now say that the region handler interface
to GPIO handlers is a raw "bit/pin" addressed interface, not
a byte-addressed interface like the system_memory handler interface.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08d1dec6f4054e3613f32051d9b149d4203ce0d2 upstream.
When we are doing compliance test with xHCI, we found that if we
enable CONFIG_USB_SUSPEND and plug in a bad device which causes
over-current condition to the root port, software will not be noticed.
The reason is that current code don't set hub->change_bits in
hub_activate() when over-current happens, and then hub_events() will
not check the port status because it thinks nothing changed.
If CONFIG_USB_SUSPEND is disabled, the interrupt pipe of the hub will
report the change and set hub->event_bits, and then hub_events() will
check what events happened.In this case over-current can be detected.
Signed-off-by: Shen Guang <shenguang10@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 81a60b7f5c143ab3cdcd9943c9b4b7c63c32fc31 upstream.
we don't to gate clocks until our children are
done with their remove path.
Fixes: af310e9 (usb: dwc3: omap: use runtime API's to enable clocks)
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7312b5ddd47fee2356baa78c5516ef8e04eed452 upstream.
Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH. This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.
But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed. Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.
Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c80b4495c61636edc58fe1ce300f09f24db28e10 upstream.
This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.
The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.
Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.
My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.
This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b6a3ed677991558ce09046397a7c4d70530d15b3 upstream.
Hi,
The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.
I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 67d365a57a51fb9dece6a5ceb504aa381cae1e5b upstream.
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.
I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c66f1c62e85927357e7b3f4c701614dcb5c498a2 upstream.
The Iomega Jaz USB Adapter is a SCSI-USB converter cable. The hardware
seems to be identical to e.g. the Microtech XpressSCSI, using a Shuttle/
SCM chip set. However its firmware restricts it to only work with Jaz
drives.
On connecting the cable a message like this appears four times in the log:
reset full speed USB device number 4 using uhci_hcd
That's non-fatal but the US_FL_SINGLE_LUN quirk fixes it.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c605f3cdff53a743f6d875b76956b239deca1272 upstream.
During surprise device hotplug removal tests, it was observed that
hub_events may try to call usb_lock_device on a device that has already
been freed. Protect the usb_device by taking out a reference (under the
hub_event_lock) when hub_events pulls it off the list, returning the
reference after hub_events is finished using it.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref
Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96044694b8511bc2b04df0776b4ba295cfe005c0 upstream.
Resuming from hibernate (S4) will restart and re-initialize xHC.
The device contexts are freed and will be re-allocated later during device reset.
Usb core will disable link pm in device resume before device reset, which will
try to change the max exit latency, accessing the device contexts before they are re-allocated.
There is no need to zero (disable) the max exit latency when disabling hw lpm
for a freshly re-initialized xHC. So check that device context exists before
doing anything. The max exit latency will be set again after device reset when usb core
enables the link pm.
Reported-by: Imre Deak <imre.deak@intel.com>
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c207e7c50f31113c24a9f536fcab1e8a256985d7 upstream.
If xhci initialization fails before the roothub bandwidth
domains (xhci->rh_bw[i]) are allocated it will oops when
trying to access rh_bw members in xhci_mem_cleanup().
Reported-by: Manuel Reimer <manuel.reimer@gmx.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3096691011d01cef56b243a5e65431405c07d574 upstream.
Add back some PIDs that were mistakingly remove when reverting commit
73228a0538a7 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.
Fixes: 63a901c06e3c ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: Lei Liu <lei35151@163.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee444609dbae8afee420c3243ce4c5f442efb622 upstream.
Add device id for NOVITUS Bono E thermal printer.
Reported-by: Emanuel Koczwara <poczta@emanuelkoczwara.pl>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5b3da69285c143b7ea76b3b9f73099ff1093ab73 upstream.
This VID:PID is used for some Direct IP devices behaving
identical to the already supported 0F3D:68AA devices.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
