summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2011-08-09rt2x00: Fix PCI interrupt processing race on SMP systemsHelmut Schaa
When toggle_irq is called for PCI devices to disable device interrupts it used tasklet_disable to wait for a possibly running tasklet to finish. However, on SMP systems the tasklet might still be scheduled on another CPU. Instead, use tasklet_kill to ensure that all scheduled tasklets are finished before returning from toggle_irq. Furthermore, it was possible that a tasklet reenabled its interrupt even though interrupts have been disabled already. Fix this by checking the DEVICE_STATE_ENABLED_RADIO flag before reenabling single interrupts during tasklet processing. While at it also enable/kill the TBTT and PRETBTT tasklets in the toggle_irq callback and only use tasklet_kill in stop_queue to wait for a currently scheduled beacon update before returning. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09rtlwifi: Remove raw read/write routines from headerLarry Finger
Now that the driver no longer uses the raw r/w routines, remove their definitions. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09rtlwifi: Eliminate raw reads and writes from PCIe portionLarry Finger
The PCIe driver used raw reads and writes on the PCIe hardware. As all of these are only affecting the configuration space, all of then can be converted to pci_{read,write}_config_XX calls. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k: Use atomic reference count for interrupt opsRajkumar Manoharan
Let us enable/disable interrupts based on reference count. By doing this we can ensure that interrupts are never be enabled in the middle of tasklet processing. Instead of addressing corner cases like "ath9k: avoid enabling interrupts while processing rx", this approach handles it in generic manner. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k_hw: Fix incorrect spur_freq_sd for AR9003Rajkumar Manoharan
Spur frequency was incorrectly computed with 10Mhz offset which could cause the filter would not notch out the spur and also this could improve rx sensitivity in HT40. Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k: do not enable interrupt on set interrupt maskRajkumar Manoharan
At preset set_interrupt also enables interrupt after changing mask. This is not necessary in all cases and also sometime it breaks the assumption that interrupt was disabled. So let us enable the interrupt explicity if it was disabled earlier. This could also avoid unnecessary register ops and also helps the follow up patch to have global ref count for interrupts ops. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k_hw: use register name in place of magic valueAlex Hacker
Signed-off-by: Alex Hacker <hacker@epn.ru> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09mwifiex: print driver version informationAmitkumar Karwar
Add code to display driver version information in dmesg after loading the driver successfully. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09libertas: implement if_sdio runtime power managementDaniel Drake
The SDIO card is now fully powered down when the network interface is brought down. Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09libertas: disable functionality when interface is downDaniel Drake
Modify the driver so that it does not function when the interface is down, in preparation for runtime power management. No commands can be run while the interface is down, so the ndo_dev_stop routine now directly does all necessary work (including asking the device to disconnect from the network and disabling multicast functionality) directly. power_save and power_restore hooks are added meaning that card drivers can take steps to turn the device off when the interface is down. The MAC address can now only be changed when all interfaces are down; the new address will be programmed when an interface gets brought up. This matches mac80211 behaviour. Also, some small cleanups/simplifications were made in the surrounding device handling logic. Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k_hw: Update AR9003 high_power tx gain tableRajkumar Manoharan
The high_power tx gain table is changed to match the low_ob_db tx gain table for both 5G and 2G. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k_hw: Update the radio parameters related to high_powerRajkumar Manoharan
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k_hw: Optimize rx descriptor processing for AR9003Rajkumar Manoharan
No need to process RxDone and ds_info status again in case valid rx status is given. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k: Remove virtual wiphy specific frame typeRajkumar Manoharan
This patch cleanups virtual wiphy specific frametype structure Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k: Dump modal eeprom headerRajkumar Manoharan
Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k/modal_eeprom Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k: Dump base eeprom headerRajkumar Manoharan
Debugfs file location: <debugfs_mnt>/ieee80211/phy#/ath9k/base_eeprom Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k_hw: Add dump_eeprom support for eeprom_defRajkumar Manoharan
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k_hw: Add dump_eeprom support for AR9287Rajkumar Manoharan
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k_hw: Add dump_eeprom support for eeprom_4kRajkumar Manoharan
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09ath9k_hw: Add dump_eeprom support for AR9003Rajkumar Manoharan
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09b43: add core rev 17 used on bcma SoC.Hauke Mehrtens
This ieee80211 core was found on a Netgear wndr3400. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-09bcma: use boardflags define from ssb codeRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath9k: use the new channel noise value for signal strength and survey infoFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath9k_hw: calculate a much better approximation of channel noiseFelix Fietkau
Currently ath9k presents the internal calibrated noise floor as channel noise measurement, however this results in highly chip specific values that are only useful as relative measurements but do not resemble any real channel noise values. In order to give a much better approximation of the real channel noise, add the difference between the measured noise floor and the nominal chip specific noise floor to the default minimum channel noise value, which is currently used to calculate the signal strength from the RSSI value. This may not be 100% accurate, but it's much better than what's there before. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08libertas_usb: program OLPC EC wakeup mask for wake-on-WLANDaniel Drake
OLPC power management code has recently gone upstream. This piece completes the puzzle for libertas_usb, which now programs the OLPC EC for wlan wakeups when they have been requested. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath9k_hw: do not limit initial tx power to 20 dbmFelix Fietkau
When testing for tx power, bypass the default limits. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath9k_hw: fix calculated runtime tx power limitFelix Fietkau
Use the previously calculated maximum of all rates instead of just the one from the lowest rate of the selected PHY mode. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath9k_hw: remove the tx power index offsetFelix Fietkau
It is always 0 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath5k: remove last references to "softc"Pavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath5k: clean up base.h and its usePavel Roskin
Remove unnecessary includes from base.h. Add includes to other files as necessary. Don't include base.h unless needed. Move declarations for functions in base.c from ath5k.h to base.h. Use a better named define to protect base.h against double inclusion. Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath: fix spelling of GrenadaPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08orinoco_cs: be more careful when matching cards with ID 0x0156:0x0002Pavel Roskin
Without CONFIG_HERMES_PRISM, only match cards that have "Version 01.01" as the third product ID. Those have Agere firmware. With CONFIG_HERMES_PRISM, match all 0x0156:0x0002 cards. Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08hostap_cs: support cards with "Version 01.02" as third product IDPavel Roskin
Cards with numeric ID 0x0156:0x0002 and third ID "Version 01.02" can be assumed to have Intersil firmware. Cards with Agere firmware use "Version 01.01". Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08b43legacy: report core numberPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08b43legacy: remove 64-bit DMA supportPavel Roskin
Devices supported by b43legacy don't support 64-bit DMA. Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08iwlagn: support v2 of enhanced sensitivity tableWey-Yi Guy
Add support for v2 of enhanced sensitivity table for 2000 series products Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08iwlagn: change default sensitivity value for 5000 and 6000 seriesWey-Yi Guy
Update the default sensitivity value for both 5000 and 6000 series devices Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08iwlagn: support new P2P implementationJohannes Berg
The previous P2P implementation turned out to not work well and new uCode capabilities were added to support P2P. Modify the driver to take advantage of those, and also discover P2P support automatically based on a uCode flag instead of having a Kconfig symbol for P2P. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08iwlagn: move context init after firmware loadingJohannes Berg
The availability of contexts depends on the firmware capabilities. Currently only the presence of the second context depends on it, but soon P2P support will also be different. Move the context initialisation code to the firmware-dependent setup before registering with mac80211 to make it easier to handle. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08iwlagn: bump firmware API for some devicesJohannes Berg
We're working on improvements for the firmware for some devices, and need to bump the API for those since they won't be backward compatible completely (the earlier patch reserving queue 10 for P2P). Bump the API version to 6 for those devices but don't warn users of version 5 yet. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08iwlagn: separate firmware version warningJohannes Berg
We sometimes need to support new firmware API for a while before we can publish them since testing them fully takes a long time. We could keep all the new code private, but that causes plenty of problems and sometimes we can give a pre-release version of firmware to people who need to test. However, when we just bump the API version, the driver will warn everybody that their firmware is outdated, when in fact it isn't. (Currently our case for this doesn't really change the API but bumping the API version is necessary because the firmware isn't fully backward compatible) In order to handle this in the future, add a new "api_ok" version; only below this will the driver warn that the uCode is too old. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08iwlagn: Remove ht40 support from 5.2GHz for _bgn devicesWey-Yi Guy
For _bgn device, remove ht40 support for 5.2GHz, it is probably ok since the "band" is not support but just feel strange. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08iwlagn: default smps mode for 1000 series deviceWey-Yi Guy
1000 series are 1x2 devices, the old default using static smps which only use single antenna for rx, set the default to dynamic smps. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08iwlagn: reserve queue 10 for TX during scan dwellJohannes Berg
New uCode images will use queue 10 for TX during scan (for P2P offchannel operation scan). We'll bump the API version of those, but before we need to reserve queue 10 and stop using it for aggregation. To simplify the code, always reserve it, we could continue using it on older uCode images but that'd be rather complicated. Also, we'll set it up to map to the right FIFO as needed later, but as we don't use the queue now that doesn't hurt. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath5k: eliminate CHANNEL_* macros, use AR5K_MODE_* in channel->hw_valuePavel Roskin
When checking for the band, use channel->band. Change ath5k_hw_nic_wakeup() and ath5k_channel_ok() to take ieee80211_channel. Change ath5k_hw_radio_revision() to take ieee80211_band. Signed-off-by: Pavel Roskin <proski@gnu.org> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath5k: remove most references to XRPavel Roskin
XR is a proprietary feature of the chipset. It's not supported and should not be supported. Signed-off-by: Pavel Roskin <proski@gnu.org> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath5k: remove unused and write-only structures and fieldsPavel Roskin
struct ath5k_avg_val is unused. In struct ath5k_hw, lladdr, ah_radar and ah_mac_revision are write-only, rxbufsize is unused, ah_phy is write-only and referenced by unused macros. In struct ath5k_vif, lladdr is write-only. Remove AR5K_TUNE_RADAR_ALERT, which has no effect. Signed-off-by: Pavel Roskin <proski@gnu.org> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08ath9k: remove all references to subsysid, it's never usedPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08bcm47xx: add support for bcma busHauke Mehrtens
This patch add support for the bcma bus. Broadcom uses only Mips 74K CPUs on the new SoC and on the old ons using ssb bus there are no Mips 74K CPUs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-08bcm47xx: make it possible to build bcm47xx without ssb.Hauke Mehrtens
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-10-05 22:05:46 +0000