| Age | Commit message (Collapse) | Author |
|---|
|
commit dfa49c4ad120a784ef1ff0717168aa79f55a483a upstream.
When parsing exponent-expressed intervals we subtract 1 from the
value and then expect it to match with original + 1, which is
highly unlikely, and we end with frequent spew:
usb 3-4: ep 0x83 - rounding interval to 512 microframes
Also, parsing interval for fullspeed isochronous endpoints was
incorrect - according to USB spec they use exponent-based
intervals (but xHCI spec claims frame-based intervals). I trust
USB spec more, especially since USB core agrees with it.
This should be queued for stable kernels back to 2.6.31.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5a6c2f3ff039154872ce597952f8b8900ea0d732 upstream.
Macro arguments used in expressions need to be enclosed in parenthesis
to avoid unpleasant surprises.
This should be queued for kernels back to 2.6.31
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2868a2b1ba8f9c7f6c4170519ebb6c62934df70e upstream.
Isochronous and interrupt SuperSpeed endpoints use the same mechanisms
for decoding bInterval values as HighSpeed ones so adjust the code
accordingly.
Also bandwidth reservation for SuperSpeed matches highspeed, not
low/full speed.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 94ae4976e253757e9b03a44d27d41b20f1829d80 upstream.
This patch (as1458) fixes a problem affecting ultra-reliable systems:
When hardware failover of an EHCI controller occurs, the data
structures do not get released correctly. This is because the routine
responsible for removing unused QHs from the async schedule assumes
the controller is running properly (the frame counter is used in
determining how long the QH has been idle) -- but when a failover
causes the controller to be electronically disconnected from the PCI
bus, obviously it stops running.
The solution is simple: Allow scan_async() to remove a QH from the
async schedule if it has been idle for long enough _or_ if the
controller is stopped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-Tested-by: Dan Duval <dan.duval@stratus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 80f9df3e0093ad9f1eeefd2ff7fd27daaa518d25 upstream.
Bind only modem AT command endpoint to option.
Signed-off-by: Marius B. Kotsbak <marius@kotsbak.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c6991b6fd2b4201174dc4620d0c8c4f5ff27b36f upstream.
This patch, adds to the option driver the Onda Communication
(http://www.ondacommunication.com) vendor id, and the MT825UP modem
device id.
Note that many variants of this same device are being release here in
Italy (at least one or two per telephony operator).
These devices are perfectly equivalent except for some predefined
settings (which can be changed of course).
It should be noted that most ONDA devices are allready supported (they
used other vendor's ids in the past). The patch seems working fine here,
and the rest of the driver seems uninfluenced.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c53c2fab40cf16e13af66f40bfd27200cda98d2f upstream.
usb serial: ftdi_sio: add two missing USB ID's for Hameg interfaces HO720
and HO730
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 11a31d84129dc3133417d626643d714c9df5317e upstream.
Add PID 0x0103 for serial port of the OCT DK201 docking station.
Reported-by: Jan Hoogenraad <jan@hoogenraad.net>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5a9443f08c83c294c5c806a689c1184b27cb26b3 upstream.
I added new ProdutIds for two devices from CTI GmbH Leipzig.
Signed-off-by: Christian Simon <simon@swine.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 468c3f924f043cad7a04f4f4d5224a2c9bc886c1 upstream.
Currently, for N 5800 XM I get:
cdc_phonet: probe of 1-6:1.10 failed with error -22
It's because phonet_header is empty. Extra altsetting looks like
there:
E 05 24 00 01 10 03 24 ab 05 24 06 0a 0b 04 24 fd .$....$..$....$.
E 00 .
I don't see the header used anywhere so just check if the phonet
descriptor is there, not the structure itself.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 14ddc3188d50855ae2a419a6aced995e2834e5d4 upstream.
Don't allow everybody to change video settings.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 18b429e74eeafe42e947b1b0f9a760c7153a0b5c upstream.
Omit pkt_hdr preamble when dumping transmitted packet as hex-dump;
we can pull this up because the frame has already been sent, and
dumping it is the last thing we do with it before freeing it.
Also include the size, vpi, and vci in the debug as is done on
receive.
Use "port" consistently instead of "device" intermittently.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit deb187e72470b0382d4f0cb859e76e1ebc3a1082 upstream.
Don't allow everybody to change device settings.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Hartley Sweeten <hartleys@visionengravers.com>
Cc: Matthieu Crapet <mcrapet@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 49d50fb1c28738ef6bad0c2b87d5355a1653fed5 upstream.
Don't allow everybogy to write to NVRAM.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Cc: Andy Sharp <andy.sharp@onstor.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f8a0697722d12a201588225999cfc8bfcbc82781 upstream.
Don't allow everybody to change device hardware registers.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1309d7afbed112f0e8e90be9af975550caa0076b upstream.
This patch fixes information leakage to the userspace by initializing
the data buffer to zero.
Reported-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)". If that isn't 1, we have way
deeper problems than a simple multiplication can fix. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 63a8588debd4dc72becb9e27add9343c76301c7d upstream.
Just adding the vendor details makes it work fine.
Signed-off-by: Marc-Antoine Perennou <Marc-Antoine@Perennou.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c85ce65ecac078ab1a1835c87c4a6319cf74660a upstream.
Otherwise, skb_put inside of dma_rx can fail...
https://bugzilla.kernel.org/show_bug.cgi?id=32042
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 220107610c7c2c9703e09eb363e8ab31025b9315 upstream.
Reported-by: Mark Davis [via p54/devices wiki]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f62d816fc4324afbb7cf90110c70b6a14139b225 upstream.
When the chip is still asleep when ath9k_start is called,
ath9k_hw_configpcipowersave can trigger a data bus error.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 22356585712d1ff08fbfed152edd8b386873b238 upstream.
Locking is required when tweaking bits located in a shared page, use the
sync_ version of bitops. Without this change vmbus_on_event() will miss
events and as a result, vmbus_isr() will not schedule the receive tasklet.
[Backported to 2.6.32 stable kernel by Haiyang Zhang <haiyangz@microsoft.com>]
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c996edcf1c451b81740abbcca5257ed7e353fcc6 upstream.
After Quick Migration, the network is not immediately operational in the
current context when receiving RNDIS_STATUS_MEDIA_CONNECT event. So, I added
another netif_notify_peers() into a scheduled work, otherwise GARP packet will
not be sent after quick migration, and cause network disconnection.
Thanks to Mike Surcouf <mike@surcouf.co.uk> for reporting the bug and
testing the patch.
Reported-by: Mike Surcouf <mike@surcouf.co.uk>
Tested-by: Mike Surcouf <mike@surcouf.co.uk>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Abhishek Kane <v-abkane@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 28276a28d8b3cd19f4449991faad4945fe557656 upstream.
For isochronous packets the actual_length is the sum of the actual
length of each of the packets, however between the packets might be
padding, so it is not sufficient to just send the first actual_length
bytes of the buffer. To fix this and simultanesouly optimize the
bandwidth the content of the isochronous packets are send without the
padding, the padding is restored on the receiving end.
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1325f85fa49f57df034869de430f7c302ae23109 upstream.
The number_of_packets was not transmitted for RET_SUBMIT packets. The
linux client used the stored number_of_packet from the submitted
request. The windows userland client does not do this however and needs
to know the number_of_packets to determine the size of the transmission.
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d2dd0b07c3e725d386d20294ec906f7ddef207fa upstream.
When doing a usb port reset do a queued reset instead to prevent a
deadlock: the reset will cause the driver to unbind, causing the
usb_driver_lock_for_reset to stall.
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 877a55979c189c590e819a61cbbe2b7947875f17 upstream.
enclosure page 7 gives us the "pretty" names of the enclosure slots.
Without a page 7, we can still use the enclosure code as long as we
make up numeric names for the slots. Unfortunately, the current code
fails to add any devices because the check for page 10 is in the wrong
place if we have no page 7. Fix it so that devices show up even if
the enclosure has no page 7.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1ddd5049545e0aa1a0ed19bca4d9c9c3ce1ac8a2 upstream.
Under certain workloads a command may seem to get lost. IOW, the Smart Array
thinks all commands have been completed but we still have commands in our
completion queue. This may lead to system instability, filesystems going
read-only, or even panics depending on the affected filesystem. We add an
extra read to force the write to complete.
Testing shows this extra read avoids the problem.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cda6587c21a887254c8ed4b58da8fcc4040ab557 upstream.
Rmmod myri10ge crash at free_netdev() -> netif_napi_del(), because napi
structures are already deallocated. To fix call netif_napi_del() before
kfree() at myri10ge_free_slices().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit dd65c736d1b5312c80c88a64bf521db4959eded5 upstream.
The dcdbas driver can do an I/O write to cause a SMI to occur. The SMI handler
looks at certain registers and memory locations, so the SMI needs to happen
immediately. On some systems I/O writes are posted, though, causing the SMI to
happen well after the "outb" occurred, which causes random failures. Following
the "outb" with an "inb" forces the write to go through even if it is posted.
Signed-off-by: Stuart Hayes <stuart_hayes@yahoo.com>
Acked-by: Doug Warzecha <douglas_warzecha@dell.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8c3c283e6bf463ab498d6e7823aff6c4762314b6 upstream.
A virtualized display device is usually viewed with the vncviewer
application, either by 'xm vnc domU' or with vncviewer localhost:port.
vncviewer and the RFB protocol provides absolute coordinates to the
virtual display. These coordinates are either passed through to a PV
guest or converted to relative coordinates for a HVM guest.
A PV guest receives these coordinates and passes them to the kernels
evdev driver. There it can be picked up by applications such as the
xorg-input drivers. Using absolute coordinates avoids issues such as
guest mouse pointer not tracking host mouse pointer due to wrong mouse
acceleration settings in the guests X display.
Advertise either absolute or relative coordinates to the input system
and the evdev driver, depending on what dom0 provides. The xorg-input
driver prefers relative coordinates even if a devices provides both.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7e7797e7f6f7bfab73fca02c65e40eaa5bb9000c upstream.
Fix potential null-pointer exception on disconnect introduced by commit
11ea859d64b69a747d6b060b9ed1520eab1161fe (USB: additional power savings
for cdc-acm devices that support remote wakeup).
Only access acm->dev after making sure it is non-null in control urb
completion handler.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 15e5bee33ffc11d0e5c6f819a65e7881c5c407be upstream.
Must check return value of tty_port_tty_get.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 23b80550e2aa61d0ba3af98b831b9195be0db9ee upstream.
Prevent read urbs from being resubmitted from tasklet after port close.
The receive tasklet was not disabled on port close, which could lead to
corruption of receive lists on consecutive port open. In particular,
read urbs could be re-submitted before port open, added to free list in
open, and then added a second time to the free list in the completion
handler.
cdc-acm.c: Entering acm_tty_open.
cdc-acm.c: acm_control_msg: rq: 0x22 val: 0x3 len: 0x0 result: 0
cdc-acm.c: Entering acm_rx_tasklet
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da280, rcv 0xf57fbc24, buf 0xf57fbd64
cdc-acm.c: set line: 115200 0 0 8
cdc-acm.c: acm_control_msg: rq: 0x20 val: 0x0 len: 0x7 result: 7
cdc-acm.c: acm_tty_close
cdc-acm.c: acm_port_down
cdc-acm.c: acm_control_msg: rq: 0x22 val: 0x0 len: 0x0 result: 0
cdc-acm.c: acm_ctrl_irq - urb shutting down with status: -2
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da300, rcv 0xf57fbc10, buf 0xf57fbd50
cdc-acm.c: Entering acm_read_bulk with status -2
cdc_acm 4-1:1.1: Aborting, acm not ready
cdc-acm.c: Entering acm_read_bulk with status -2
cdc_acm 4-1:1.1: Aborting, acm not ready
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da380, rcv 0xf57fbbfc, buf 0xf57fbd3c
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da400, rcv 0xf57fbbe8, buf 0xf57fbd28
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da480, rcv 0xf57fbbd4, buf 0xf57fbd14
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da900, rcv 0xf57fbbc0, buf 0xf57fbd00
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da980, rcv 0xf57fbbac, buf 0xf57fbcec
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50daa00, rcv 0xf57fbb98, buf 0xf57fbcd8
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50daa80, rcv 0xf57fbb84, buf 0xf57fbcc4
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50dab00, rcv 0xf57fbb70, buf 0xf57fbcb0
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50dab80, rcv 0xf57fbb5c, buf 0xf57fbc9c
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50dac00, rcv 0xf57fbb48, buf 0xf57fbc88
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50dac80, rcv 0xf57fbb34, buf 0xf57fbc74
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50dad00, rcv 0xf57fbb20, buf 0xf57fbc60
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50dad80, rcv 0xf57fbb0c, buf 0xf57fbc4c
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da880, rcv 0xf57fbaf8, buf 0xf57fbc38
cdc-acm.c: Entering acm_tty_open.
cdc-acm.c: acm_control_msg: rq: 0x22 val: 0x3 len: 0x0 result: 0
cdc-acm.c: Entering acm_rx_tasklet
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da280, rcv 0xf57fbc24, buf 0xf57fbd64
cdc-acm.c: Entering acm_tty_write to write 3 bytes,
cdc-acm.c: Get 3 bytes...
cdc-acm.c: acm_write_start susp_count: 0
cdc-acm.c: Entering acm_read_bulk with status 0
------------[ cut here ]------------
WARNING: at /home/johan/src/linux/linux-2.6/lib/list_debug.c:57 list_del+0x10c/0x120()
Hardware name: Vostro 1520
list_del corruption. next->prev should be f57fbc10, but was f57fbaf8
Modules linked in: cdc_acm
Pid: 3, comm: ksoftirqd/0 Not tainted 2.6.37+ #39
Call Trace:
[<c103c7e2>] warn_slowpath_common+0x72/0xa0
[<c11dd8ac>] ? list_del+0x10c/0x120
[<c11dd8ac>] ? list_del+0x10c/0x120
[<c103c8b3>] warn_slowpath_fmt+0x33/0x40
[<c11dd8ac>] list_del+0x10c/0x120
[<f8051dbf>] acm_rx_tasklet+0xef/0x3e0 [cdc_acm]
[<c135465d>] ? net_rps_action_and_irq_enable+0x6d/0x80
[<c1042bb6>] tasklet_action+0xe6/0x140
[<c104342f>] __do_softirq+0xaf/0x210
[<c1043380>] ? __do_softirq+0x0/0x210
<IRQ> [<c1042c9a>] ? run_ksoftirqd+0x8a/0x1c0
[<c1042c10>] ? run_ksoftirqd+0x0/0x1c0
[<c105ac24>] ? kthread+0x74/0x80
[<c105abb0>] ? kthread+0x0/0x80
[<c100337a>] ? kernel_thread_helper+0x6/0x10
---[ end trace efd9a11434f0082e ]---
------------[ cut here ]------------
WARNING: at /home/johan/src/linux/linux-2.6/lib/list_debug.c:57 list_del+0x10c/0x120()
Hardware name: Vostro 1520
list_del corruption. next->prev should be f57fbd50, but was f57fbdb0
Modules linked in: cdc_acm
Pid: 3, comm: ksoftirqd/0 Tainted: G W 2.6.37+ #39
Call Trace:
[<c103c7e2>] warn_slowpath_common+0x72/0xa0
[<c11dd8ac>] ? list_del+0x10c/0x120
[<c11dd8ac>] ? list_del+0x10c/0x120
[<c103c8b3>] warn_slowpath_fmt+0x33/0x40
[<c11dd8ac>] list_del+0x10c/0x120
[<f8051dd6>] acm_rx_tasklet+0x106/0x3e0 [cdc_acm]
[<c135465d>] ? net_rps_action_and_irq_enable+0x6d/0x80
[<c1042bb6>] tasklet_action+0xe6/0x140
[<c104342f>] __do_softirq+0xaf/0x210
[<c1043380>] ? __do_softirq+0x0/0x210
<IRQ> [<c1042c9a>] ? run_ksoftirqd+0x8a/0x1c0
[<c1042c10>] ? run_ksoftirqd+0x0/0x1c0
[<c105ac24>] ? kthread+0x74/0x80
[<c105abb0>] ? kthread+0x0/0x80
[<c100337a>] ? kernel_thread_helper+0x6/0x10
---[ end trace efd9a11434f0082f ]---
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da300, rcv 0xf57fbc10, buf 0xf57fbd50
cdc-acm.c: disconnected from network
cdc-acm.c: acm_rx_tasklet: sending urb 0xf50da380, rcv 0xf57fbbfc, buf 0xf57fbd3c
cdc-acm.c: Entering acm_rx_tasklet
------------[ cut here ]------------
WARNING: at /home/johan/src/linux/linux-2.6/lib/list_debug.c:48 list_del+0xd5/0x120()
Hardware name: Vostro 1520
list_del corruption, next is LIST_POISON1 (00100100)
Modules linked in: cdc_acm
Pid: 3, comm: ksoftirqd/0 Tainted: G W 2.6.37+ #39
Call Trace:
[<c103c7e2>] warn_slowpath_common+0x72/0xa0
[<c11dd875>] ? list_del+0xd5/0x120
[<c11dd875>] ? list_del+0xd5/0x120
[<c103c8b3>] warn_slowpath_fmt+0x33/0x40
[<c11dd875>] list_del+0xd5/0x120
[<f8051fac>] acm_rx_tasklet+0x2dc/0x3e0 [cdc_acm]
[<c106dbab>] ? trace_hardirqs_on+0xb/0x10
[<c1042b30>] ? tasklet_action+0x60/0x140
[<c1042bb6>] tasklet_action+0xe6/0x140
[<c104342f>] __do_softirq+0xaf/0x210
[<c1043380>] ? __do_softirq+0x0/0x210
<IRQ> [<c1042c9a>] ? run_ksoftirqd+0x8a/0x1c0
[<c1042c10>] ? run_ksoftirqd+0x0/0x1c0
[<c105ac24>] ? kthread+0x74/0x80
[<c105abb0>] ? kthread+0x0/0x80
[<c100337a>] ? kernel_thread_helper+0x6/0x10
---[ end trace efd9a11434f00830 ]---
BUG: unable to handle kernel paging request at 00200200
IP: [<c11dd7bd>] list_del+0x1d/0x120
*pde = 00000000
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.0/tty/ttyACM0/uevent
Modules linked in: cdc_acm
Pid: 3, comm: ksoftirqd/0 Tainted: G W 2.6.37+ #39 0T816J/Vostro 1520
EIP: 0060:[<c11dd7bd>] EFLAGS: 00010046 CPU: 0
EIP is at list_del+0x1d/0x120
EAX: f57fbd3c EBX: f57fb800 ECX: ffff8000 EDX: 00200200
ESI: f57fbe90 EDI: f57fbd3c EBP: f600bf54 ESP: f600bf3c
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process ksoftirqd/0 (pid: 3, ti=f600a000 task=f60791c0 task.ti=f6082000)
Stack:
c1527e84 00000030 c1527e54 00100100 f57fb800 f57fbd3c f600bf98 f8051fac
f8053104 f8052b94 f600bf6c c106dbab f600bf80 00000286 f60791c0 c1042b30
f57fbda8 f57f5800 f57fbdb0 f57fbd80 f57fbe7c c1656b04 00000000 f600bfb0
Call Trace:
[<f8051fac>] ? acm_rx_tasklet+0x2dc/0x3e0 [cdc_acm]
[<c106dbab>] ? trace_hardirqs_on+0xb/0x10
[<c1042b30>] ? tasklet_action+0x60/0x140
[<c1042bb6>] ? tasklet_action+0xe6/0x140
[<c104342f>] ? __do_softirq+0xaf/0x210
[<c1043380>] ? __do_softirq+0x0/0x210
<IRQ>
[<c1042c9a>] ? run_ksoftirqd+0x8a/0x1c0
[<c1042c10>] ? run_ksoftirqd+0x0/0x1c0
[<c105ac24>] ? kthread+0x74/0x80
[<c105abb0>] ? kthread+0x0/0x80
[<c100337a>] ? kernel_thread_helper+0x6/0x10
Code: ff 48 14 e9 57 ff ff ff 90 90 90 90 90 90 55 89 e5 83 ec 18 81 38 00 01 10 00 0f 84 9c 00 00 00 8b 50 04 81 fa 00 02 20 00 74 33 <8b> 12 39 d0 75 5c 8b 10 8b 4a 04 39 c8 0f 85 b5 00 00 00 8b 48
EIP: [<c11dd7bd>] list_del+0x1d/0x120 SS:ESP 0068:f600bf3c
CR2: 0000000000200200
---[ end trace efd9a11434f00831 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Pid: 3, comm: ksoftirqd/0 Tainted: G D W 2.6.37+ #39
Call Trace:
[<c13fede1>] ? printk+0x1d/0x24
[<c13fecce>] panic+0x66/0x15c
[<c10067df>] oops_end+0x8f/0x90
[<c1025476>] no_context+0xc6/0x160
[<c10255a8>] __bad_area_nosemaphore+0x98/0x140
[<c103cf68>] ? release_console_sem+0x1d8/0x210
[<c1025667>] bad_area_nosemaphore+0x17/0x20
[<c1025a49>] do_page_fault+0x279/0x420
[<c1006a8f>] ? show_trace+0x1f/0x30
[<c13fede1>] ? printk+0x1d/0x24
[<c10257d0>] ? do_page_fault+0x0/0x420
[<c140333b>] error_code+0x5f/0x64
[<c103007b>] ? select_task_rq_fair+0x37b/0x6a0
[<c10257d0>] ? do_page_fault+0x0/0x420
[<c11dd7bd>] ? list_del+0x1d/0x120
[<f8051fac>] acm_rx_tasklet+0x2dc/0x3e0 [cdc_acm]
[<c106dbab>] ? trace_hardirqs_on+0xb/0x10
[<c1042b30>] ? tasklet_action+0x60/0x140
[<c1042bb6>] tasklet_action+0xe6/0x140
[<c104342f>] __do_softirq+0xaf/0x210
[<c1043380>] ? __do_softirq+0x0/0x210
<IRQ> [<c1042c9a>] ? run_ksoftirqd+0x8a/0x1c0
[<c1042c10>] ? run_ksoftirqd+0x0/0x1c0
[<c105ac24>] ? kthread+0x74/0x80
[<c105abb0>] ? kthread+0x0/0x80
[<c100337a>] ? kernel_thread_helper+0x6/0x10
panic occurred, switching back to text console
------------[ cut here ]------------
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit adaa3c6342b249548ea830fe8e02aa5b45be8688 upstream.
My testprog do a lot of bitbang - after hours i got following warning and my machine lockups:
WARNING: at /build/buildd/linux-2.6.38/lib/kref.c:34
After debugging uss720 driver i discovered that the completion callback was called before
usb_submit_urb returns. The callback frees the request structure that is krefed on return by
usb_submit_urb.
Signed-off-by: Peter Holik <peter@holik.at>
Acked-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b5a3b3d985493c173925907adfebf3edab236fe7 upstream.
This patch (as1453) fixes a long-standing bug in the ehci-hcd driver.
There is no need to set the Halt bit in the overlay region for an
unlinked or blocked QH. Contrary to what the comment says, setting
the Halt bit does not cause the QH to be patched later; that decision
(made in qh_refresh()) depends only on whether the QH is currently
pointing to a valid qTD. Likewise, setting the Halt bit does not
prevent completions from activating the QH while it is "stopped"; they
are prevented by the fact that qh_completions() temporarily changes
qh->qh_state to QH_STATE_COMPLETING.
On the other hand, there are circumstances in which the QH will be
reactivated _without_ being patched; this happens after an URB beyond
the head of the queue is unlinked. Setting the Halt bit will then
cause the hardware to see the QH with both the Active and Halt bits
set, an invalid combination that will prevent the queue from
advancing and may even crash some controllers.
Apparently the only reason this hasn't been reported before is that
unlinking URBs from the middle of a running queue is quite uncommon.
However Test 17, recently added to the usbtest driver, does exactly
this, and it confirms the presence of the bug.
In short, there is no reason to set the Halt bit for an unlinked or
blocked QH, and there is a very good reason not to set it. Therefore
the code that sets it is removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andiry Xu <andiry.xu@amd.com>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 38a66824d96de8aeeb915e6f46f0d3fe55828eb1 upstream.
The scheme used to index format in uvc_fixup_video_ctrl() is not robust:
format index is based on descriptor ordering, which does not necessarily
match bFormatIndex ordering. Searching for first matching format will
prevent uvc_fixup_video_ctrl() from using the wrong format/frame to make
adjustments.
Signed-off-by: Stephan Lachowsky <stephan.lachowsky@maxim-ic.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d6244bc0ed0c52a795e6f4dcab3886daf3e74fac upstream.
Use mask 0x10 for "soft cursor" detection on in function tile_cursor.
(Tile Blitting Operation in framebuffer console).
The old mask 0x01 for vc_cursor_type detects CUR_NONE, CUR_LOWER_THIRD
and every second mode value as "software cursor". This hides the cursor
for these modes (cursor.mode = 0). But, only CUR_NONE or "software cursor"
should hide the cursor.
See also 0x10 in functions add_softcursor, bit_cursor and cw_cursor.
Signed-off-by: Henry Nestler <henry.nestler@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 447c5dd7338638f526e9bcf7dcf69b4da5835c7d upstream.
A successful write() to the "reset" sysfs attribute should return the
number of bytes written, not 0. Otherwise userspace (bash) retries the
write over and over again.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 47e9037ac16637cd7f12b8790ea7ce6680e42168 upstream.
If a device doesn't support power management (pm_cap == 0) but it is
acpi_pci_power_manageable() because there is a _PS0 method declared for
it and _EJ0 is also declared for the slot then nobody is going to set
current_state = PCI_D0 for this device. This is what I think it is
happening:
pci_enable_device
|
__pci_enable_device_flags
/* here we do not set current_state because !pm_cap */
|
do_pci_enable_device
|
pci_set_power_state
|
__pci_start_power_transition
|
pci_platform_power_transition
/* platform_pci_power_manageable() calls acpi_pci_power_manageable that
* returns true */
|
platform_pci_set_power_state
/* acpi_pci_set_power_state gets called and does nothing because the
* acpi device has _EJ0, see the comment "If the ACPI device has _EJ0,
* ignore the device" */
at this point if we refer to the commit message that introduced the
comment above (10b3dcae0f275e2546e55303d64ddbb58cec7599), it is up to
the hotplug driver to set the state to D0.
However AFAICT the pci hotplug driver never does, in fact
drivers/pci/hotplug/acpiphp_glue.c:register_slot sets the slot flags to
(SLOT_ENABLED | SLOT_POWEREDON) but it does not set the pci device
current state to PCI_D0.
So my proposed fix is also to set current_state = PCI_D0 in
register_slot.
Comments are very welcome.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ccd32e735de7a941906e093f8dca924bb05c5794 upstream.
An integer overflow occurs in the calculation of RHlinear when the
relative humidity is greater than around 30%. The consequence is a subtle
(but noticeable) error in the resulting humidity measurement.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0aab3995485b8a994bf29a995a008c9ea4a28054 upstream.
During redetection of a SDIO card, a request for a new card RCA
was submitted to the card, but was then overwritten by the old RCA.
This caused the card to be deselected instead of selected when using
the incorrect RCA. This bug's been present since the "oldcard"
handling was introduced in 2.6.32.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Reviewed-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Pawel Wieczorkiewicz <pawel.wieczorkiewicz@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bc10f96757bd6ab3721510df8defa8f21c32f974 upstream.
Remove the call to tty_ldisc_flush() from the RESULT_NO_CARRIER
branch of isdn_tty_modem_result(), as already proposed in commit
00409bb045887ec5e7b9e351bc080c38ab6bfd33.
This avoids a "sleeping function called from invalid context" BUG
when the hardware driver calls the statcallb() callback with
command==ISDN_STAT_DHUP in atomic context, which in turn calls
isdn_tty_modem_result(RESULT_NO_CARRIER, ~), and from there,
tty_ldisc_flush() which may sleep.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0f12a4e29368a9476076515881d9ef4e5876c6e2 upstream.
Commit 280c73d ("PCI: centralize the capabilities code in
pci-sysfs.c") changed the initialisation of the "rom" and "vpd"
attributes, and made the failure path for the "vpd" attribute
incorrect. We must free the new attribute structure (attr), but
instead we currently free dev->vpd->attr. That will normally be NULL,
resulting in a memory leak, but it might be a stale pointer, resulting
in a double-free.
Found by inspection; compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 87e3dc3855430bd254370afc79f2ed92250f5b7c upstream.
Some broken BIOSes on ICH4 chipset report an ACPI region which is in
conflict with legacy IDE ports when ACPI is disabled. Even though the
regions overlap, IDE ports are working correctly (we cannot find out
the decoding rules on chipsets).
So the only problem is the reported region itself, if we don't reserve
the region in the quirk everything works as expected.
This patch avoids reserving any quirk regions below PCIBIOS_MIN_IO
which is 0x1000. Some regions might be (and are by a fast google
query) below this border, but the only difference is that they won't
be reserved anymore. They should still work though the same as before.
The conflicts look like (1f.0 is bridge, 1f.1 is IDE ctrl):
pci 0000:00:1f.1: address space collision: [io 0x0170-0x0177] conflicts with 0000:00:1f.0 [io 0x0100-0x017f]
At 0x0100 a 128 bytes long ACPI region is reported in the quirk for
ICH4. ata_piix then fails to find disks because the IDE legacy ports
are zeroed:
ata_piix 0000:00:1f.1: device not available (can't reserve [io 0x0000-0x0007])
References: https://bugzilla.novell.com/show_bug.cgi?id=558740
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cdb9755849fbaf2bb9c0a009ba5baa817a0f152d upstream.
Per ICH4 and ICH6 specs, ACPI and GPIO regions are valid iff ACPI_EN
and GPIO_EN bits are set to 1. Add checks for these bits into the
quirks prior to the region creation.
While at it, name the constants by macros.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b99af4b002e4908d1a5cdaf424529bdf1dc69768 upstream.
Revert commit 7eb93b175d4de9438a4b0af3a94a112cb5266944
Author: Yu Zhao <yu.zhao@intel.com>
Date: Fri Apr 3 15:18:11 2009 +0800
PCI: SR-IOV quirk for Intel 82576 NIC
If BIOS doesn't allocate resources for the SR-IOV BARs, zero the Flash
BAR and program the SR-IOV BARs to use the old Flash Memory Space.
Please refer to Intel 82576 Gigabit Ethernet Controller Datasheet
section 7.9.2.14.2 for details.
http://download.intel.com/design/network/datashts/82576_Datasheet.pdf
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This quirk was added before SR-IOV was in production and now all machines that
originally had this issue alreayd have bios updates to correct the issue. The
quirk itself is no longer needed and in fact causes bugs if run. Remove it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Yu Zhao <yu.zhao@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 01a1fdb9a7afa5e3c14c9316d6f380732750b4e4 upstream.
When an endpoint stalls, we need to update the xHCI host's internal
dequeue pointer to move it past the stalled transfer. This includes
updating the cycle bit (TRB ownership bit) if we have moved the dequeue
pointer past a link TRB with the toggle cycle bit set.
When we're trying to find the new dequeue segment, find_trb_seg() is
supposed to keep track of whether we've passed any link TRBs with the
toggle cycle bit set. However, this while loop's body
while (cur_seg->trbs > trb ||
&cur_seg->trbs[TRBS_PER_SEGMENT - 1] < trb) {
Will never get executed if the ring only contains one segment.
find_trb_seg() will return immediately, without updating the new cycle
bit. Since find_trb_seg() has no idea where in the segment the TD that
stalled was, make the caller, xhci_find_new_dequeue_state(), check for
this special case and update the cycle bit accordingly.
This patch should be queued to kernels all the way back to 2.6.31.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d0781383038e983a63843a9a6a067ed781db89c1 upstream.
I picked up a new DAK-780EX(professional digitl reverb/mix system),
which use CH341T chipset to communication with computer on 3/2011
and the CH341T's vendor code is 1a86
Looking up the CH341T's vendor and product id's I see:
1a86 QinHeng Electronics
5523 CH341 in serial mode, usb to serial port converter
CH341T,CH341 are the products of the same company, maybe
have some common hardware, and I test the ch341.c works
well with CH341T
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6960f40a954619857e7095a6179eef896f297077 upstream.
Make sure that we check the return value of tty_port_tty_get.
Sometimes it may return NULL and we later dereference that.
The only place here is in kobil_read_int_callback, so fix it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ac45c12dfb3f727a5a7a3332ed9c11b4a5ab287e upstream.
There are few places where we are checking for macversion and revsions
before RTC is powered ON. However we are reading the macversion and
revisions only after RTC is powered ON and so both macversion and
revisions are actully zero and this leads to incorrect srev checks
Incorrect srev checks can cause registers to be configured wrongly and can
cause unexpected behavior. Fixing this seems to address the ASPM issue that
we have observed. The laptop becomes very slow and hangs mostly with ASPM L1
enabled without this fix.
fix this by reading the macversion and revisisons even before we start
using them. There is no reason why should we delay reading this info
until RTC is powered on as this is just a register information.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
