| Age | Commit message (Collapse) | Author |
|---|
|
commit d4dc210f69bcb0b4bef5a83b1c323817be89bad1 upstream.
Disk event code automatically blocks events on excl write. This is
primarily to avoid issuing polling commands while burning is in
progress. This behavior doesn't fit other types of devices with
removeable media where polling commands don't have adverse side
effects and door locking usually doesn't exist.
This patch introduces new genhd flag which controls the auto-blocking
behavior and uses it to enable auto-blocking only on optical devices.
Note for stable: 2.6.38 and later only
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 63c4408074cbcc070ac17fc10e524800eb9bd0b0 upstream.
TI816X (common name for DM816x/C6A816x/AM389x family) devices configured
to boot as PCIe Endpoint have class code = 0. This makes kernel PCI bus
code to skip allocating BARs to these devices resulting into following
type of error when trying to enable them:
"Device 0000:01:00.0 not available because of resource collisions"
The device cannot be operated because of the above issue.
This patch adds a ID specific (TI VENDOR ID and 816X DEVICE ID based)
'early' fixup quirk to replace class code with
PCI_CLASS_MULTIMEDIA_VIDEO as class.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 97bfd0acd32e9639c9136e03955d574655d5cc2b upstream.
None of the latest GPUs had this hooked up, this is necessary for
correct operation in a lot of cases, however we should test this on a few
GPUs in these families as we've had problems in this area before.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cde5083b051e9c66c99a8764aefbc13349e7730d upstream.
cayman is reporting the wrong tile config value to userspace, this
causes piglit mipmap generation tests to fail.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c289cff10a265ec4afe4396425297ff979a840b5 upstream.
This was leading to a bogus value being programmed to the backend
routing register.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f25a5c63bfa017498c9adecb24d649ae96ba5c68 upstream.
This needs to be explicitly set on btc. It's set by default
on evergreen/fusion, so it fine to just unconditionally enable it for
all chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 0b65f83f9d2fab47b9b6040fe75fc2cfc73032d4 upstream.
On cayman we need to set the bit to cause HDP flushes to invalidate the
HDP cache also.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5bfa1063a775836a84f97e4df863fc36e1f856ad upstream.
On g4x, user interrupt in BSD ring is missed.
This is because though g4x and ironlake share the same bsd_ring,
their interrupt control interfaces have _two_ differences.
1.different irq enable/disable functions:
On g4x are i915_enable_irq and i915_disable_irq.
On ironlake are ironlake_enable_irq and ironlake_disable_irq.
2.different irq flag:
On g4x user interrupt flag in BSD ring on is I915_BSD_USER_INTERRUPT.
On ironlake is GT_BSD_USER_INTERRUPT
Old bsd_ring_get/put_irq call ring_get_irq and ring_get_irq.
ring_get_irq and ring_put_irq only call ironlake_enable/disable_irq.
So comes the irq miss on g4x.
To fix this, as other rings' code do, conditionally call different
functions(i915_enable/disable_irq and ironlake_enable/disable_irq)
and use different interrupt flags in bsd_ring_get/put_irq.
Signed-off-by: Boqun Feng <boqun.feng@intel.com>
Reviewed-by: Xiang, Haihao <haihao.xiang@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit af46566885a373b0a526932484cd8fef8de7b598 upstream.
When finding or allocating a ram disk device, brd_probe() did not take
partition numbers into account so that it can result to a different
device. Consider following example (I set CONFIG_BLK_DEV_RAM_COUNT=4
for simplicity) :
$ sudo modprobe brd max_part=15
$ ls -l /dev/ram*
brw-rw---- 1 root disk 1, 0 2011-05-25 15:41 /dev/ram0
brw-rw---- 1 root disk 1, 16 2011-05-25 15:41 /dev/ram1
brw-rw---- 1 root disk 1, 32 2011-05-25 15:41 /dev/ram2
brw-rw---- 1 root disk 1, 48 2011-05-25 15:41 /dev/ram3
$ sudo mknod /dev/ram4 b 1 64
$ sudo dd if=/dev/zero of=/dev/ram4 bs=4k count=256
256+0 records in
256+0 records out
1048576 bytes (1.0 MB) copied, 0.00215578 s, 486 MB/s
namhyung@leonhard:linux$ ls -l /dev/ram*
brw-rw---- 1 root disk 1, 0 2011-05-25 15:41 /dev/ram0
brw-rw---- 1 root disk 1, 16 2011-05-25 15:41 /dev/ram1
brw-rw---- 1 root disk 1, 32 2011-05-25 15:41 /dev/ram2
brw-rw---- 1 root disk 1, 48 2011-05-25 15:41 /dev/ram3
brw-r--r-- 1 root root 1, 64 2011-05-25 15:45 /dev/ram4
brw-rw---- 1 root disk 1, 1024 2011-05-25 15:44 /dev/ram64
After this patch, /dev/ram4 - instead of /dev/ram64 - was
accessed correctly.
In addition, 'range' passed to blk_register_region() should
include all range of dev_t that RAMDISK_MAJOR can address.
It does not need to be limited by partition numbers unless
'rd_nr' param was specified.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 315980c8688c4b06713c1a5fe9d64cdf8ab57a72 upstream.
The 'max_part' parameter controls the number of maximum partition
a brd device can have. However if a user specifies very large
value it would exceed the limitation of device minor number and
can cause a kernel panic (or, at least, produce invalid device
nodes in some cases).
On my desktop system, following command kills the kernel. On qemu,
it triggers similar oops but the kernel was alive:
$ sudo modprobe brd max_part=100000
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
IP: [<ffffffff81110a9a>] sysfs_create_dir+0x2d/0xae
PGD 7af1067 PUD 7b19067 PMD 0
Oops: 0000 [#1] SMP
last sysfs file:
CPU 0
Modules linked in: brd(+)
Pid: 44, comm: insmod Tainted: G W 2.6.39-qemu+ #158 Bochs Bochs
RIP: 0010:[<ffffffff81110a9a>] [<ffffffff81110a9a>] sysfs_create_dir+0x2d/0xae
RSP: 0018:ffff880007b15d78 EFLAGS: 00000286
RAX: ffff880007b05478 RBX: ffff880007a52760 RCX: ffff880007b15dc8
RDX: ffff880007a4f900 RSI: ffff880007b15e48 RDI: ffff880007a52760
RBP: ffff880007b15da8 R08: 0000000000000002 R09: 0000000000000000
R10: ffff880007b15e48 R11: ffff880007b05478 R12: 0000000000000000
R13: ffff880007b05478 R14: 0000000000400920 R15: 0000000000000063
FS: 0000000002160880(0063) GS:ffff880007c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000058 CR3: 0000000007b1c000 CR4: 00000000000006b0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
Process insmod (pid: 44, threadinfo ffff880007b14000, task ffff880007acb980)
Stack:
ffff880007b15dc8 ffff880007b05478 ffff880007b15da8 00000000fffffffe
ffff880007a52760 ffff880007b05478 ffff880007b15de8 ffffffff81143c0a
0000000000400920 ffff880007a52760 ffff880007b05478 0000000000000000
Call Trace:
[<ffffffff81143c0a>] kobject_add_internal+0xdf/0x1a0
[<ffffffff81143da1>] kobject_add_varg+0x41/0x50
[<ffffffff81143e6b>] kobject_add+0x64/0x66
[<ffffffff8113bbe7>] blk_register_queue+0x5f/0xb8
[<ffffffff81140f72>] add_disk+0xdf/0x289
[<ffffffffa00040df>] brd_init+0xdf/0x1aa [brd]
[<ffffffffa0004000>] ? 0xffffffffa0003fff
[<ffffffffa0004000>] ? 0xffffffffa0003fff
[<ffffffff8100020a>] do_one_initcall+0x7a/0x12e
[<ffffffff8108516c>] sys_init_module+0x9c/0x1dc
[<ffffffff812ff4bb>] system_call_fastpath+0x16/0x1b
Code: 89 e5 41 55 41 54 53 48 89 fb 48 83 ec 18 48 85 ff 75 04 0f 0b eb fe 48 8b 47 18 49 c7 c4 70 1e 4d 81 48 85 c0 74 04 4c 8b 60 30
8b 44 24 58 45 31 ed 0f b6 c4 85 c0 74 0d 48 8b 43 28 48 89
RIP [<ffffffff81110a9a>] sysfs_create_dir+0x2d/0xae
RSP <ffff880007b15d78>
CR2: 0000000000000058
---[ end trace aebb1175ce1f6739 ]---
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6f13f6fba76edc7d0e7580c5deee829d59a41b2f upstream.
Integrity errors need to be passed to the owner of the integrity
metadata for processing. Consequently EILSEQ should be passed up the
stack.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f4808ca99a203f20b4475601748e44b25a65bdec upstream.
This patch adds a check that a block device has a request function
defined before it is used. Otherwise, misconfiguration can cause an oops.
Because we are allowing devices with zero size e.g. an offline multipath
device as in commit 2cd54d9bedb79a97f014e86c0da393416b264eb3
("dm: allow offline devices") there needs to be an additional check
to ensure devices are initialised. Some block devices, like a loop
device without a backing file, exist but have no request function.
Reproducer is trivial: dm-mirror on unbound loop device
(no backing file on loop devices)
dmsetup create x --table "0 8 mirror core 2 8 sync 2 /dev/loop0 0 /dev/loop1 0"
and mirror resync will immediatelly cause OOps.
BUG: unable to handle kernel NULL pointer dereference at (null)
? generic_make_request+0x2bd/0x590
? kmem_cache_alloc+0xad/0x190
submit_bio+0x53/0xe0
? bio_add_page+0x3b/0x50
dispatch_io+0x1ca/0x210 [dm_mod]
? read_callback+0x0/0xd0 [dm_mirror]
dm_io+0xbb/0x290 [dm_mod]
do_mirror+0x1e0/0x748 [dm_mirror]
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7467571f4480b273007517b26297c07154c73924 upstream.
Cpuidle menu governor is using u32 as a temporary datatype for storing
nanosecond values which wrap around at 4.294 seconds. This causes errors
in predicted sleep times resulting in higher than should be C state
selection and increased power consumption. This also breaks cpuidle
state residency statistics.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit eec752b2b99c794766926a9bac59b0d7df5b09c2 upstream.
Initialize sysfs attrs before device_create_file() call to suppress
lockdep_init_map() warning:
WARNING: at kernel/lockdep.c:2701 lockdep_init_map+0x12d/0x140()
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bc1f419c76a2d6450413ce4349f4e4a07be011d5 upstream.
i8k uses lahf to read the flag register in 64-bit code; early x86-64
CPUs, however, lack this instruction and we get an invalid opcode
exception at runtime.
Use pushf to load the flag register into the stack instead.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Reported-by: Jeff Rickman <jrickman@myamigos.us>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Tested-by: Harry G McGavran Jr <w5pny@arrl.net>
Cc: Massimo Dal Zotto <dz@debian.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9368a9a2378ab721f82f59430a135b4ce4ff5109 upstream.
Reported-by: Mark Davis <marked86@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6eb6fbbf3eca6dfba73e72de5ab2eeb52ae41f7a upstream.
The disabling of clocks and freeing GPIO are changed
to fix the occurrence of the crash of rmmod of ehci and ohci
drivers. The GPIOs should be freed after the spin locks are
unlocked.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 52c10ad22b7e317960b4d411c9a9ddeaf3d5ae39 upstream.
div6 clock should not use arch_flags for clk_rate_table_build,
because SH_CLK_DIV6_EXT doesn't care .arch_flags.
clk->freq_table[] will be all CPUFREQ_ENTRY_INVALID without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1d6213ab995c61f7d1d81cf6cf876acf15d6e714 upstream.
cx8802_blackbird_probe makes a device node for the mpeg sub-device
before it has been added to dev->drvlist. If the device is opened
during that time, the open succeeds but request_acquire cannot be
called, so the reference count remains zero. Later, when the device
is closed, the reference count becomes negative --- uh oh.
Close the race by holding core->lock during probe and not releasing
until the device is in drvlist and initialization finished.
Previously the BKL prevented this race.
Reported-by: Andreas Huber <hobrom@gmx.at>
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 1fe70e963028f34ba5e32488a7870ff4b410b19b upstream.
The BKL conversion of this driver seems to have gone wrong.
Loading the cx88-blackbird driver deadlocks.
The cause: mpeg_ops::open in the cx2388x blackbird driver acquires the
device lock and calls the sub-driver's request_acquire, which tries to
acquire the lock again. Fix it by clarifying the semantics of
request_acquire, request_release, advise_acquire, and advise_release:
now all will rely on the caller to acquire the device lock.
Based on work by Ben Hutchings <ben@decadent.org.uk>.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=31962
Reported-by: Andi Huber <hobrom@gmx.at>
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8a317a8760cfffa8185b56ff59fb4b6c58488d79 upstream.
The BKL conversion of this driver seems to have gone wrong. Various
uses of the sub-device and driver lists appear to be subject to race
conditions.
In particular, some functions access drvlist without a relevant lock
held, which will race against removal of drivers. Let's start with
that --- clean up by consistently protecting dev->drvlist with
dev->core->lock, noting driver functions that require the device lock
to be held or not to be held.
After this patch, there are still some races --- e.g.,
cx8802_blackbird_remove can run between the time the blackbird driver
is acquired and the time it is used in mpeg_release, and there's a
similar race in cx88_dvb_bus_ctrl. Later patches will address the
remaining known races and the deadlock noticed by Andi. This patch
just makes the semantics clearer in preparation for those later
changes.
Based on work by Ben Hutchings <ben@decadent.org.uk>.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5a0deeed5741117ee8625d6305d0034e219f102c upstream.
This patch removes the remaining on-stack buffer for USB DMA transfer.
This patch also reduces the stack memory usage.
Cc: Florian Mickler <florian@mickler.org>
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 69fff59de4d844f8b4c2454c3c23d32b69dcbfd7 upstream.
This patch (as1467) removes the last usages of hcd->state from
usbcore. We no longer check to see if an interrupt handler finds that
a controller has died; instead we rely on host controller drivers to
make an explicit call to usb_hc_died().
This fixes a regression introduced by commit
9b37596a2e860404503a3f2a6513db60c296bfdc (USB: move usbcore away from
hcd->state). It used to be that when a controller shared an IRQ with
another device and an interrupt arrived while hcd->state was set to
HC_STATE_HALT, the interrupt handler would be skipped. The commit
removed that test; as a result the current code doesn't skip calling
the handler and ends up believing the controller has died, even though
it's only temporarily stopped. The solution is to ignore HC_STATE_HALT
following the handler's return.
As a consequence of this change, several of the host controller
drivers need to be modified. They can no longer implicitly rely on
usbcore realizing that a controller has died because of hcd->state.
The patch adds calls to usb_hc_died() in the appropriate places.
The patch also changes a few of the interrupt handlers. They don't
expect to be called when hcd->state is equal to HC_STATE_HALT, even if
the controller is still alive. Early returns were added to avoid any
confusion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Manuel Lauss <manuel.lauss@googlemail.com>
CC: Rodolfo Giometti <giometti@linux.it>
CC: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2b7aaf503d56216b847c8265421d2a7d9b42df3e upstream.
This patch (as1463) fixes a regression caused by commit
3df7169e73fc1d71a39cffeacc969f6840cdf52b (OHCI: work around for nVidia
shutdown problem).
The original problem encountered by people using NVIDIA chipsets was
that USB devices were not turning off when the system shut down. For
example, the LED on an optical mouse would remain on, draining a
laptop's battery. The problem was caused by a bug in the chipset; an
OHCI controller in the Reset state would continue to drive a bus reset
signal even after system shutdown. The workaround was to put the
controllers into the Suspend state instead.
It turns out that later NVIDIA chipsets do not suffer from this bug.
Instead some have the opposite bug: If a system is shut down while an
OHCI controller is in the Suspend state, USB devices remain powered!
On other systems, shutting down with a Suspended controller causes the
system to reboot immediately. Thus, working around the original bug
on some machines exposes other bugs on other machines.
The best solution seems to be to limit the workaround to OHCI
controllers with a low-numbered PCI product ID. I don't know exactly
at what point NVIDIA changed their chipsets; the value used here is a
guess. So far it was worked out okay for all the people who have
tested it.
This fixes Bugzilla #35032.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com>
Tested-by: Yury Siamashka <yurand2@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 610ba42f29c3dfa46a05ff8c2cadc29f544ff76d upstream.
I am sharing patch to the devices/usb/serial/option.c. This allows
operation of Huawei E353 broadband modem using the “option” driver. The
patch simply adds new constant with proper product ID and an entry to
usb_device_id. I worked on the 2.6.38.6 sources. Tested on Dell inspiron
1764 (i3 core cpu) and brand new Huawei E353 modem, Fedora 15 beta.
Looking at the type of change, i doubt it has potential to introduce
problems in other parts of kernel or the driver itself.
Signed-off-by: Marcin Galczynski <marcin@galczynski.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 834cb0fc4712a3b21c6b8c5cb55bd13607191311 upstream.
When the USB core wants to change to an alternate interface setting that
doesn't include an active endpoint, or de-configuring the device, the xHCI
driver needs to issue a Configure Endpoint command to tell the host to
drop some endpoints from the schedule. After the command completes, the
xHCI driver needs to free rings for any endpoints that were dropped.
Unfortunately, the xHCI driver wasn't actually freeing the endpoint rings
for dropped endpoints. The rings would be freed if the endpoint's
information was simply changed (and a new ring was installed), but dropped
endpoints never had their rings freed. This caused errors when the ring
segment DMA pool was freed when the xHCI driver was unloaded:
[ 5582.883995] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff88003371d000 busy
[ 5582.884002] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033716000 busy
[ 5582.884011] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033455000 busy
[ 5582.884018] xhci_hcd 0000:06:00.0: Freed segment pool
[ 5582.884026] xhci_hcd 0000:06:00.0: Freed device context pool
[ 5582.884033] xhci_hcd 0000:06:00.0: Freed small stream array pool
[ 5582.884038] xhci_hcd 0000:06:00.0: Freed medium stream array pool
[ 5582.884048] xhci_hcd 0000:06:00.0: xhci_stop completed - status = 1
[ 5582.884061] xhci_hcd 0000:06:00.0: USB bus 3 deregistered
[ 5582.884193] xhci_hcd 0000:06:00.0: PCI INT A disabled
Fix this issue and free endpoint rings when their endpoints are
successfully dropped.
This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 30f89ca021c3e584b61bc5a14eede89f74b2e826 upstream.
When an endpoint ring is freed, it is either cached in a per-device ring
cache, or simply freed if the ring cache is full. If the ring was added
to the cache, then virt_dev->num_rings_cached is incremented. The cache
is designed to hold up to 31 endpoint rings, in array indexes 0 to 30.
When the device is freed (when the slot was disabled),
xhci_free_virt_device() is called, it would free the cached rings in
array indexes 0 to virt_dev->num_rings_cached.
Unfortunately, the original code in xhci_free_or_cache_endpoint_ring()
would put the first entry into the ring cache in array index 1, instead of
array index 0. This was caused by the second assignment to rings_cached:
rings_cached = virt_dev->num_rings_cached;
if (rings_cached < XHCI_MAX_RINGS_CACHED) {
virt_dev->num_rings_cached++;
rings_cached = virt_dev->num_rings_cached;
virt_dev->ring_cache[rings_cached] =
virt_dev->eps[ep_index].ring;
This meant that when the device was freed, cached rings with indexes 0 to
N would be freed, and the last cached ring in index N+1 would not be
freed. When the driver was unloaded, this caused interesting messages
like:
xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880063040000 busy
This should be queued to stable kernels back to 2.6.33.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b513d44751bfb609a3c20463f764c8ce822d63e9 upstream.
Dmitry's patch
dfa49c4ad120a784ef1ff0717168aa79f55a483a USB: xhci - fix math in xhci_get_endpoint_interval()
introduced a bug. The USB 2.0 spec says that full speed isochronous endpoints'
bInterval must be decoded as an exponent to a power of two (e.g. interval =
2^(bInterval - 1)). Full speed interrupt endpoints, on the other hand, don't
use exponents, and the interval in frames is encoded straight into bInterval.
Dmitry's patch was supposed to fix up the full speed isochronous to parse
bInterval as an exponent, but instead it changed the *interrupt* endpoint
bInterval decoding. The isochronous endpoint encoding was the same.
This caused full speed devices with interrupt endpoints (including mice, hubs,
and USB to ethernet devices) to fail under NEC 0.96 xHCI host controllers:
[ 100.909818] xhci_hcd 0000:06:00.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x99, new slot info = 0x38100000
[ 100.909821] xhci_hcd 0000:06:00.0: xhci_check_bandwidth called for udev ffff88011f0ea000
...
[ 100.910187] xhci_hcd 0000:06:00.0: ERROR: unexpected command completion code 0x11.
[ 100.910190] xhci_hcd 0000:06:00.0: xhci_reset_bandwidth called for udev ffff88011f0ea000
When the interrupt endpoint was added and a Configure Endpoint command was
issued to the host, the host controller would return a very odd error message
(0x11 means "Slot Not Enabled", which isn't true because the slot was enabled).
Probably the host controller was getting very confused with the bad encoding.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Dmitry Torokhov <dtor@vmware.com>
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Tested-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 472b91274a6c6857877b5caddb875dcb5ecdfcb8 upstream.
composite.c always sets req->length to zero
and expects function driver's setup handlers
to return the amount of bytes to be used
on req->length. If we test against req->length
w_length will always be greater than req->length
thus making us always stall that particular
SEND_ENCAPSULATED_COMMAND request.
Tested against a Windows XP SP3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit bf1f0a05d472e33dda8e5e69525be1584cdbd03a upstream.
on 9g20 they are the same as the 9260
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3abeca998a44205cfd837fa0bf1f7c24f8294acb upstream.
When the xHCI driver attempts to cancel a transfer, it issues a Stop
Endpoint command and waits for the host controller to indicate which TRB
it was in the middle of processing. The host will put an event TRB with
completion code COMP_STOP on the event ring if it stops on a control
transfer TRB (or other types of transfer TRBs). The ring handling code
is supposed to set ep->stopped_trb to the TRB that the host stopped on
when this happens.
Unfortunately, there is a long-standing bug in the control transfer
completion code. It doesn't actually check to see if COMP_STOP is set
before attempting to process the transfer based on which part of the
control TD completed. So when we get an event on the data phase of the
control TRB with COMP_STOP set, it thinks it's a normal completion of
the transfer and doesn't set ep->stopped_td or ep->stopped_trb.
When the ring handling code goes on to process the completion of the Stop
Endpoint command, it sees that ep->stopped_trb is not a part of the TD
it's trying to cancel. It thinks the hardware has its enqueue pointer
somewhere further up in the ring, and thinks it's safe to turn the control
TRBs into no-op TRBs. Since the hardware was in the middle of the control
TRBs to be cancelled, the proper software behavior is to issue a Set TR
dequeue pointer command.
It turns out that the NEC host controllers can handle active TRBs being
set to no-op TRBs after a stop endpoint command, but other host
controllers have issues with this out-of-spec software behavior. Fix this
behavior.
This patch should be backported to kernels as far back as 2.6.31, but it
may be a bit challenging, since process_ctrl_td() was introduced in some
refactoring done in 2.6.36, and some endian-safe patches added in 2.6.40
that touch the same lines.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit fd5054c169d29747a44b4e1419ff47f57ae82dbc upstream.
The Droids MuIn LCD operates like a serial remote terminal.
Data received are displayed directly on the LCD. This patch
fixes the kernel null pointer oops when it is plugged in.
Add NO_DATA_INTERFACE quirk to tell the driver that "control"
and "data" interfaces are not separated for this device, which
prevents dereferencing a null pointer in the device probe code.
Signed-off-by: Erik Slagter <erik@slagter.name>
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Tested-by: Erik Slagter <erik@slagter.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 15b2f3204a5c878c32939094775fb7349f707263 upstream.
Network interface is handled by upcoming gt_b3730 module.
Removed "GT-B3710" from comment, it is another modem with another USB ID.
Signed-off-by: Marius B. Kotsbak <marius@kotsbak.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b4026c4584cd70858d4d3450abfb1cd0714d4f32 upstream.
This patch fixes a problem where data received from the gps is sometimes
transferred incompletely to the serial port. If used in native mode now
all data received via the bulk queue will be forwarded to the serial
port.
Signed-off-by: Hermann Kneissel <herkne@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 37909fe588c9e09ab57cd267e98678a17ceda64a upstream.
Adding support for the TavIR STK500 (id 0403:FA33)
Atmel AVR programmer device based on FTDI FT232RL.
Signed-off-by: Benedek László <benedekl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3938a0b32dc12229e76735679b37095bc2bc1578 upstream.
Tested on my phone, the ttyUSB device is created and is fully
functional.
Signed-off-by: Elizabeth Jennifer Myers <elizabeth@sporksirc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4eff0b40a7174896b860312910e0db51f2dcc567 upstream.
This patch adds 4 device IDs for CP2102 based devices manufactured by
AC-Services. See http://www.ac-services.eu for further info.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 65a1a0ace554d61ea5a90377a54df1505275c1b1 upstream.
For Tegra i2c controller to function properly new slave mode must be
enabled.
swarren notes:
In particular, I found this was needed when working on enabling the
Tegra audio driver on the Seaboard board. There are two different PCB
layouts for this board; a "clamshell" version, which works just fine
without this change, and the original non-clamshell version, which needs
this change in order for I2C to operate correctly. Without it, I2C
probing fails for some devices, e.g. with:
wm8903 0-001a: Device with ID register 0 is not a WM8903
wm8903 0-001a: asoc: failed to probe CODEC wm8903.0-001a: -19
asoc: failed to instantiate card tegra-wm8903: -19
ALSA device list:
No soundcards found.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a1c15c59feee36267c43142a41152fbf7402afb6 upstream.
When finding or allocating a loop device, loop_probe() did not take
partition numbers into account so that it can result to a different
device. Consider following example:
$ sudo modprobe loop max_part=15
$ ls -l /dev/loop*
brw-rw---- 1 root disk 7, 0 2011-05-24 22:16 /dev/loop0
brw-rw---- 1 root disk 7, 16 2011-05-24 22:16 /dev/loop1
brw-rw---- 1 root disk 7, 32 2011-05-24 22:16 /dev/loop2
brw-rw---- 1 root disk 7, 48 2011-05-24 22:16 /dev/loop3
brw-rw---- 1 root disk 7, 64 2011-05-24 22:16 /dev/loop4
brw-rw---- 1 root disk 7, 80 2011-05-24 22:16 /dev/loop5
brw-rw---- 1 root disk 7, 96 2011-05-24 22:16 /dev/loop6
brw-rw---- 1 root disk 7, 112 2011-05-24 22:16 /dev/loop7
$ sudo mknod /dev/loop8 b 7 128
$ sudo losetup /dev/loop8 ~/temp/disk-with-3-parts.img
$ sudo losetup -a
/dev/loop128: [0805]:278201 (/home/namhyung/temp/disk-with-3-parts.img)
$ ls -l /dev/loop*
brw-rw---- 1 root disk 7, 0 2011-05-24 22:16 /dev/loop0
brw-rw---- 1 root disk 7, 16 2011-05-24 22:16 /dev/loop1
brw-rw---- 1 root disk 7, 2048 2011-05-24 22:18 /dev/loop128
brw-rw---- 1 root disk 7, 2049 2011-05-24 22:18 /dev/loop128p1
brw-rw---- 1 root disk 7, 2050 2011-05-24 22:18 /dev/loop128p2
brw-rw---- 1 root disk 7, 2051 2011-05-24 22:18 /dev/loop128p3
brw-rw---- 1 root disk 7, 32 2011-05-24 22:16 /dev/loop2
brw-rw---- 1 root disk 7, 48 2011-05-24 22:16 /dev/loop3
brw-rw---- 1 root disk 7, 64 2011-05-24 22:16 /dev/loop4
brw-rw---- 1 root disk 7, 80 2011-05-24 22:16 /dev/loop5
brw-rw---- 1 root disk 7, 96 2011-05-24 22:16 /dev/loop6
brw-rw---- 1 root disk 7, 112 2011-05-24 22:16 /dev/loop7
brw-r--r-- 1 root root 7, 128 2011-05-24 22:17 /dev/loop8
After this patch, /dev/loop8 - instead of /dev/loop128 - was
accessed correctly.
In addition, 'range' passed to blk_register_region() should
include all range of dev_t that LOOP_MAJOR can address. It does
not need to be limited by partition numbers unless 'max_loop'
param was specified.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 78f4bb367fd147a0e7e3998ba6e47109999d8814 upstream.
The 'max_part' parameter controls the number of maximum partition
a loop block device can have. However if a user specifies very
large value it would exceed the limitation of device minor number
and can cause a kernel panic (or, at least, produce invalid
device nodes in some cases).
On my desktop system, following command kills the kernel. On qemu,
it triggers similar oops but the kernel was alive:
$ sudo modprobe loop max_part0000
------------[ cut here ]------------
kernel BUG at /media/Linux_Data/project/linux/fs/sysfs/group.c:65!
invalid opcode: 0000 [#1] SMP
last sysfs file:
CPU 0
Modules linked in: loop(+)
Pid: 43, comm: insmod Tainted: G W 2.6.39-qemu+ #155 Bochs Bochs
RIP: 0010:[<ffffffff8113ce61>] [<ffffffff8113ce61>] internal_create_group=
+0x2a/0x170
RSP: 0018:ffff880007b3fde8 EFLAGS: 00000246
RAX: 00000000ffffffef RBX: ffff880007b3d878 RCX: 00000000000007b4
RDX: ffffffff8152da50 RSI: 0000000000000000 RDI: ffff880007b3d878
RBP: ffff880007b3fe38 R08: ffff880007b3fde8 R09: 0000000000000000
R10: ffff88000783b4a8 R11: ffff880007b3d878 R12: ffffffff8152da50
R13: ffff880007b3d868 R14: 0000000000000000 R15: ffff880007b3d800
FS: 0000000002137880(0063) GS:ffff880007c00000(0000) knlGS:00000000000000=
00
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000422680 CR3: 0000000007b50000 CR4: 00000000000006b0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
Process insmod (pid: 43, threadinfo ffff880007b3e000, task ffff880007afb9c=
0)
Stack:
ffff880007b3fe58 ffffffff811e66dd ffff880007b3fe58 ffffffff811e570b
0000000000000010 ffff880007b3d800 ffff880007a7b390 ffff880007b3d868
0000000000400920 ffff880007b3d800 ffff880007b3fe48 ffffffff8113cfc8
Call Trace:
[<ffffffff811e66dd>] ? device_add+0x4bc/0x5af
[<ffffffff811e570b>] ? dev_set_name+0x3c/0x3e
[<ffffffff8113cfc8>] sysfs_create_group+0xe/0x12
[<ffffffff810b420e>] blk_trace_init_sysfs+0x14/0x16
[<ffffffff8116a090>] blk_register_queue+0x47/0xf7
[<ffffffff8116f527>] add_disk+0xdf/0x290
[<ffffffffa00060eb>] loop_init+0xeb/0x1b8 [loop]
[<ffffffffa0006000>] ? 0xffffffffa0005fff
[<ffffffff8100020a>] do_one_initcall+0x7a/0x12e
[<ffffffff81096804>] sys_init_module+0x9c/0x1e0
[<ffffffff813329bb>] system_call_fastpath+0x16/0x1b
Code: c3 55 48 89 e5 41 57 41 56 41 89 f6 41 55 41 54 49 89 d4 53 48 89 fb=
48 83 ec 28 48 85 ff 74 0b 85 f6 75 0b 48 83 7f 30 00 75 14 <0f> 0b eb fe =
48 83 7f 30 00 b9 ea ff ff ff 0f 84 18 01 00 00 49
RIP [<ffffffff8113ce61>] internal_create_group+0x2a/0x170
RSP <ffff880007b3fde8>
---[ end trace a123eb592043acad ]---
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 23746a66d7d9e73402c68ef00d708796b97ebd72 upstream.
The device reponds with 'invalid report id' when feature report switching it
into multitouch mode is sent to it.
This has been silently ignored before 0825411ade ("HID: bt: Wait for ACK
on Sent Reports"), but since this commit, it propagates -EIO from the _raw
callback .
So let the driver ignore -EIO as response to 0xd7,0x01 report, as that's
how the device reacts in normal mode.
Sad, but following reality.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=35022
Tested-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8258c53208d7a9b7207e7d4dae36d2ea384cb278 upstream.
If a bitmap is found to be 'stale' the events_cleared value
is set to match 'events'.
However if the array is degraded this does not get stored on disk.
This can subsequently lead to incorrect behaviour.
So change bitmap_update_sb to always update events_cleared in the
superblock from the known events_cleared.
For neatness also set ->state from ->flags.
This requires updating ->state whenever we update ->flags, which makes
sense anyway.
This is suitable for any active -stable release.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b0140891a8cea36469f58d23859e599b1122bd37 upstream.
There is a race when creating an md device by opening /dev/mdXX.
If two processes do this at much the same time they will follow the
call path
__blkdev_get -> get_gendisk -> kobj_lookup
The first will call
-> md_probe -> md_alloc -> add_disk -> blk_register_region
and the race happens when the second gets to kobj_lookup after
add_disk has called blk_register_region but before it returns to
md_alloc.
In the case the second will not call md_probe (as the probe is already
done) but will get a handle on the gendisk, return to __blkdev_get
which will then call md_open (via the ->open) pointer.
As mddev->gendisk hasn't been set yet, md_open will think something is
wrong an return with ERESTARTSYS.
This can loop endlessly while the first thread makes no progress
through add_disk. Nothing is blocking it, but due to scheduler
behaviour it doesn't get a turn.
So this is essentially a live-lock.
We fix this by simply moving the assignment to mddev->gendisk before
the call the add_disk() so md_open doesn't get confused.
Also move blk_queue_flush earlier because add_disk should be as late
as possible.
To make sure that md_open doesn't complete until md_alloc has done all
that is needed, we take mddev->open_mutex during the last part of
md_alloc. md_open will wait for this.
This can cause a lock-up on boot so Cc:ing for stable.
For 2.6.36 and earlier a different patch will be needed as the
'blk_queue_flush' call isn't there.
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Tested-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e9c661e08c2a6015c1b7cba1cecefa27a089df71 upstream.
Caused by brcmsmac.ko suppling a 0 value to Mac80211. Mac80211 subsequently
divides by this number. Bug only occurred on AMPDU traffic. This is a fix
for https://bugzilla.kernel.org/show_bug.cgi?id=32032, titled
'Divide error in minstrel_ht_tx_status followed by hang', reported by
Wouter Cloetens.
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 62819fd9481021db7f87d5f61f2e2fd2be1dfcfa upstream.
Driver r8712u is unable to handle ad-hoc mode. The issue is that when
the driver first starts, there will not be an SSID for association.
The fix is to always call the "select and join from scan" routine when
in ad-hoc mode.
Note: Ad-hoc mode worked intermittently before. If the driver had
previously been associated, then things were OK.
Signed-off-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit cacd18a8476ce145ca5dcd46dc5b75585fd1289c upstream.
Fix number_of_packets wrong endian conversion in function
correct_endian_ret_submit()
Signed-off-by: David Chang <dchang@novell.com>
Acked-by: Arjan Mels <arjan.mels@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit af57c3ac9947990da2608561b71f4799eb7795c6 upstream.
This patch fixes a bug where task->task_execute_queue=1 was not being
cleared once se_task had been removed from se_device->execute_task_list,
resulting in an OOPs in core_tmr_lun_reset() for the task->task_active=0
case where transport_remove_task_from_execute_queue() was incorrectly
being called.
This patch fixes two cases in transport_get_task_from_execute_queue()
and transport_remove_task_from_execute_queue() to properly clear
task->task_execute_queue=0 once list_del(&task->t_execute_list) has
been called.
It also adds an explict check in transport_remove_task_from_execute_queue()
to dump_stack + return if called with task->task_execute_queue=0.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f436677262a5b524ac87675014c6d4e8ee153029 upstream.
This patch addresses a bug in the target core release path for HW
operation where transport_free_dev_tasks() was incorrectly being called
from transport_lun_remove_cmd() while releasing a se_cmd reference and
calling struct target_core_fabric_ops->queue_data_in().
This would result in a OOPs with HW target mode when the release of
se_task->task_sg[] would happen before pci_unmap_sg() can be called in
HW target mode fabric module code. This patch addresses the issue by
moving transport_free_dev_tasks() from transport_lun_remove_cmd() into
transport_generic_free_cmd(), and adding TRANSPORT_FREE_CMD_INTR and
transport_generic_free_cmd_intr() to allow se_cmd descriptor release
to happen fromfrom within transport_processing_thread() process context
when release of se_cmd is not possible from HW interrupt context.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 53ab6709b4d35b1924240854d794482fd7d33d4a upstream.
This patch fixes two bugs wrt to the interrupt context usage of target
core with HW target mode drivers. It first converts the usage of struct
se_device->stats_lock in transport_get_lun_for_cmd() and core_tmr_lun_reset()
to properly use spin_lock_irq() to address an BUG with CONFIG_LOCKDEP_SUPPORT=y
enabled.
This patch also adds a 'in_interrupt()' check to allow GFP_ATOMIC usage from
core_tmr_alloc_req() to fix a 'sleeping in interrupt context' BUG with HW
target fabrics that require this logic to function.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 97868c8905a1537153d406c4a3aa39a503a5c299 upstream.
This patch fixes a bug in transport_do_task_sg_chain() used by HW target
mode modules with sg_chain() to provide a single sg_next() walkable memory
layout for use with pci_map_sg() and friends. This patch addresses an
issue with mapping multiple small block max_sector tasks across multiple
struct se_task->task_sg[] mappings for HW target mode operation.
This was causing OOPs with (cmd->t_task->t_tasks_no > 1) I/O traffic for
HW target drivers using transport_do_task_sg_chain(), and has been tested
so far with tcm_fc(openfcoe), tcm_qla2xxx, and ib_srpt fabrics with
t_tasks_no > 1 IBLOCK backends using a smaller max_sectors to trigger the
original issue.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
