| Age | Commit message (Collapse) | Author |
|---|
|
In 3.2, unlike mainline, efi_pstore_erase() calls efi_pstore_write()
with a size of 0, as the underlying EFI interface treats a size of 0
as meaning deletion.
This was not taken into account in my backport of commit d80a361d779a
'efi_pstore: Check remaining space with QueryVariableInfo() before
writing data'. The size check should be omitted when erasing.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit c19b3b0f6eed552952845e4ad908dba2113d67b4 upstream.
When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed. Consecutive (debug-) output of that mode thus yields 0 for
vsync. This simple fix also speeds up future invocations of
drm_mode_vrefresh().
While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 16dad1d743d31a104a849c8944e6b9eb479f6cd7 upstream.
EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these. The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.
See
http://en.wikipedia.org/wiki/EDID
and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 132c803f7b70b17322579f6f4f3f65cf68e55135 upstream.
NVIDIA's Tegra SoC allows read/write of controller register only
if controller clock is enabled. System hangs if read/write happens
to registers without enabling clock.
clk_prepare_enable() can be fail due to unknown reason and hence
adding check for return value of this function. If this function
success then only access register otherwise return to caller with
error.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
[bwh: Backported to 3.2:
- Adjust context
- Keep calling clk_enable() directly]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d7971051e4df825e0bc11b995e87bfe86355b8e5 upstream.
Make sure the interface is not released before our serial device.
Note that drivers are still not allowed to access the interface in
any way that may interfere with another driver that may have gotten
bound to the same interface after disconnect returns.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5492bf3d5655b4954164f69c02955a7fca267611 upstream.
Add missing get_icount field to two-port driver.
The two-port driver was not updated when switching to the new icount
interface in commit 0bca1b913aff ("tty: Convert the USB drivers to the
new icount interface").
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 618aa1068df29c37a58045fe940f9106664153fd upstream.
Remove bogus disconnect test introduced by 95bef012e ("USB: more serial
drivers writing after disconnect") which prevented queued data from
being freed on disconnect.
The possible IO it was supposed to prevent is long gone.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit e971318bbed610e28bb3fde9d548e6aaf0a6b02e upstream.
Some firmware exhibits a bug where the same VariableName and
VendorGuid values are returned on multiple invocations of
GetNextVariableName(). See,
https://bugzilla.kernel.org/show_bug.cgi?id=47631
As a consequence of such a bug, Andre reports hitting the following
WARN_ON() in the sysfs code after updating the BIOS on his, "Gigabyte
Technology Co., Ltd. To be filled by O.E.M./Z77X-UD3H, BIOS F19e
11/21/2012)" machine,
[ 0.581554] EFI Variables Facility v0.08 2004-May-17
[ 0.584914] ------------[ cut here ]------------
[ 0.585639] WARNING: at /home/andre/linux/fs/sysfs/dir.c:536 sysfs_add_one+0xd4/0x100()
[ 0.586381] Hardware name: To be filled by O.E.M.
[ 0.587123] sysfs: cannot create duplicate filename '/firmware/efi/vars/SbAslBufferPtrVar-01f33c25-764d-43ea-aeea-6b5a41f3f3e8'
[ 0.588694] Modules linked in:
[ 0.589484] Pid: 1, comm: swapper/0 Not tainted 3.8.0+ #7
[ 0.590280] Call Trace:
[ 0.591066] [<ffffffff81208954>] ? sysfs_add_one+0xd4/0x100
[ 0.591861] [<ffffffff810587bf>] warn_slowpath_common+0x7f/0xc0
[ 0.592650] [<ffffffff810588bc>] warn_slowpath_fmt+0x4c/0x50
[ 0.593429] [<ffffffff8134dd85>] ? strlcat+0x65/0x80
[ 0.594203] [<ffffffff81208954>] sysfs_add_one+0xd4/0x100
[ 0.594979] [<ffffffff81208b78>] create_dir+0x78/0xd0
[ 0.595753] [<ffffffff81208ec6>] sysfs_create_dir+0x86/0xe0
[ 0.596532] [<ffffffff81347e4c>] kobject_add_internal+0x9c/0x220
[ 0.597310] [<ffffffff81348307>] kobject_init_and_add+0x67/0x90
[ 0.598083] [<ffffffff81584a71>] ? efivar_create_sysfs_entry+0x61/0x1c0
[ 0.598859] [<ffffffff81584b2b>] efivar_create_sysfs_entry+0x11b/0x1c0
[ 0.599631] [<ffffffff8158517e>] register_efivars+0xde/0x420
[ 0.600395] [<ffffffff81d430a7>] ? edd_init+0x2f5/0x2f5
[ 0.601150] [<ffffffff81d4315f>] efivars_init+0xb8/0x104
[ 0.601903] [<ffffffff8100215a>] do_one_initcall+0x12a/0x180
[ 0.602659] [<ffffffff81d05d80>] kernel_init_freeable+0x13e/0x1c6
[ 0.603418] [<ffffffff81d05586>] ? loglevel+0x31/0x31
[ 0.604183] [<ffffffff816a6530>] ? rest_init+0x80/0x80
[ 0.604936] [<ffffffff816a653e>] kernel_init+0xe/0xf0
[ 0.605681] [<ffffffff816ce7ec>] ret_from_fork+0x7c/0xb0
[ 0.606414] [<ffffffff816a6530>] ? rest_init+0x80/0x80
[ 0.607143] ---[ end trace 1609741ab737eb29 ]---
There's not much we can do to work around and keep traversing the
variable list once we hit this firmware bug. Our only solution is to
terminate the loop because, as Lingzhu reports, some machines get
stuck when they encounter duplicate names,
> I had an IBM System x3100 M4 and x3850 X5 on which kernel would
> get stuck in infinite loop creating duplicate sysfs files because,
> for some reason, there are several duplicate boot entries in nvram
> getting GetNextVariableName into a circle of iteration (with
> period > 2).
Also disable the workqueue, as efivar_update_sysfs_entries() uses
GetNextVariableName() to figure out which variables have been created
since the last iteration. That algorithm isn't going to work if
GetNextVariableName() returns duplicates. Note that we don't disable
EFI variable creation completely on the affected machines, it's just
that any pstore dump-* files won't appear in sysfs until the next
boot.
Reported-by: Andre Heider <a.heider@gmail.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Tested-by: Lingzhu Xiang <lxiang@redhat.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
[bwh: Backported to 3.2: reason is not checked in efi_pstore_write()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ec50bd32f1672d38ddce10fb1841cbfda89cfe9a upstream.
It's not wise to assume VariableNameSize represents the length of
VariableName, as not all firmware updates VariableNameSize in the same
way (some don't update it at all if EFI_SUCCESS is returned). There
are even implementations out there that update VariableNameSize with
values that are both larger than the string returned in VariableName
and smaller than the buffer passed to GetNextVariableName(), which
resulted in the following bug report from Michael Schroeder,
> On HP z220 system (firmware version 1.54), some EFI variables are
> incorrectly named :
>
> ls -d /sys/firmware/efi/vars/*8be4d* | grep -v -- -8be returns
> /sys/firmware/efi/vars/dbxDefault-pport8be4df61-93ca-11d2-aa0d-00e098032b8c
> /sys/firmware/efi/vars/KEKDefault-pport8be4df61-93ca-11d2-aa0d-00e098032b8c
> /sys/firmware/efi/vars/SecureBoot-pport8be4df61-93ca-11d2-aa0d-00e098032b8c
> /sys/firmware/efi/vars/SetupMode-Information8be4df61-93ca-11d2-aa0d-00e098032b8c
The issue here is that because we blindly use VariableNameSize without
verifying its value, we can potentially read garbage values from the
buffer containing VariableName if VariableNameSize is larger than the
length of VariableName.
Since VariableName is a string, we can calculate its size by searching
for the terminating NULL character.
Reported-by: Frederic Crozat <fcrozat@suse.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Michael Schroeder <mls@suse.com>
Cc: Lee, Chun-Yi <jlee@suse.com>
Cc: Lingzhu Xiang <lxiang@redhat.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a93bc0c6e07ed9bac44700280e65e2945d864fd4 upstream.
[Problem]
efi_pstore creates sysfs entries, which enable users to access to NVRAM,
in a write callback. If a kernel panic happens in an interrupt context,
it may fail because it could sleep due to dynamic memory allocations during
creating sysfs entries.
[Patch Description]
This patch removes sysfs operations from a write callback by introducing
a workqueue updating sysfs entries which is scheduled after the write
callback is called.
Also, the workqueue is kicked in a just oops case.
A system will go down in other cases such as panic, clean shutdown and emergency
restart. And we don't need to create sysfs entries because there is no chance for
users to access to them.
efi_pstore will be robust against a kernel panic in an interrupt context with this patch.
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
[bwh: Backported to 3.2:
- Adjust contest
- Don't check reason in efi_pstore_write(), as it is not given as a
parameter
- Move up declaration of __efivars]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ca0ba26fbbd2d81c43085df49ce0abfe34535a90 upstream.
The 'CONFIG_' prefix is not implicit in IS_ENABLED().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
commit ec0971ba5372a4dfa753f232449d23a8fd98490e upstream.
We know that with some firmware implementations writing too much data to
UEFI variables can lead to bricking machines. Recent changes attempt to
address this issue, but for some it may still be prudent to avoid
writing large amounts of data until the solution has been proven on a
wide variety of hardware.
Crash dumps or other data from pstore can potentially be a large data
source. Add a pstore_module parameter to efivars to allow disabling its
use as a backend for pstore. Also add a config option,
CONFIG_EFI_VARS_PSTORE_DEFAULT_DISABLE, to allow setting the default
value of this paramter to true (i.e. disabled by default).
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit ed9dc8ce7a1c8115dba9483a9b51df8b63a2e0ef upstream.
Add a new option, CONFIG_EFI_VARS_PSTORE, which can be set to N to
avoid using efivars as a backend to pstore, as some users may want to
compile out the code completely.
Set the default to Y to maintain backwards compatability, since this
feature has always been enabled until now.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f046f89a99ccfd9408b94c653374ff3065c7edb3 upstream.
Fix a bug in dm_btree_remove that could leave leaf values with incorrect
reference counts. The effect of this was that removal of a shared block
could result in the space maps thinking the block was no longer used.
More concretely, if you have a thin device and a snapshot of it, sending
a discard to a shared region of the thin could corrupt the snapshot.
Thinp uses a 2-level nested btree to store it's mappings. This first
level is indexed by thin device, and the second level by logical
block.
Often when we're removing an entry in this mapping tree we need to
rebalance nodes, which can involve shadowing them, possibly creating a
copy if the block is shared. If we do create a copy then children of
that node need to have their reference counts incremented. In this
way reference counts percolate down the tree as shared trees diverge.
The rebalance functions were incrementing the children at the
appropriate time, but they were always assuming the children were
internal nodes. This meant the leaf values (in our case packed
block/flags entries) were not being incremented.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
[bwh: Backported to 3.2: bump target version numbers from 1.0.1 to 1.0.2]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 511f3c5326eabe1ece35202a404c24c0aeacc246 upstream.
This patch (as1666) fixes a regression in the UDC core. The core
takes care of unbinding gadget drivers, and it does the unbinding
before telling the UDC driver to turn off the controller hardware.
When the call to the udc_stop callback is made, the gadget no longer
has a driver. The callback routine should not be invoked with a
pointer to the old driver; doing so can cause problems (such as
use-after-free accesses in net2280).
This patch should be applied, with appropriate context changes, to all
the stable kernels going back to 3.1.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[bwh: Backported to 3.2: adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit f8264340e694604863255cc0276491d17c402390 upstream.
According to XHCI specification (5.5.2.1) the IP is bit 0 and IE is bit 1
of IMAN register. Previously their definitions were reversed.
Even though there are no ill effects being observed from the swapped
definitions (because IMAN_IP is RW1C and in legacy PCI case we come in
with it already set to 1 so it was clearing itself even though we were
setting IMAN_IE instead of IMAN_IP), we should still correct the values.
This patch should be backported to kernels as old as 2.6.36, that
contain the commit 4e833c0b87a30798e67f06120cecebef6ee9644c "xhci: don't
re-enable IE constantly".
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit fa8d387dc3f62062a6b4afbbb2a3438094fd8584 upstream.
Fixes a segfault on asics without a blit callback.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=62239
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[bwh: Backported to 3.2: s/copy\.blit/copy_blit/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 29f86e66428ee083aec106cca1748dc63d98ce23 upstream.
Device stucks on filesystem writes, unless following quirk is passed:
echo 04e8:5136:m > /sys/module/usb_storage/parameters/quirks
Add corresponding entry to unusual_devs.h
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 00eed9c814cb8f281be6f0f5d8f45025dc0a97eb upstream.
xhci has its own interrupt enabling routine, which will try to
use MSI-X/MSI if present. So the usb core shouldn't try to enable
legacy interrupts; on some machines the xhci legacy IRQ setting
is invalid.
v3: Be careful to not break XHCI_BROKEN_MSI workaround (by trenn)
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Frederik Himpe <fhimpe@vub.ac.be>
Cc: David Haerdeman <david@hardeman.nu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 3118a4f652c7b12c752f3222af0447008f9b2368 upstream.
It is possible to wrap the counter used to allocate the buffer for
relocation copies. This could lead to heap writing overflows.
CVE-2013-0913
v3: collapse test, improve comment
v2: move check into validate_exec_list
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Pinkie Pie
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 2563a4524febe8f4a98e717e02436d1aaf672aa2 upstream.
Masks kernel address info-leak in object dumps with the %pK suffix,
so they cannot be used to target kernel memory corruption attacks if
the kptr_restrict sysctl is set.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: the rest of the format string is different]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit fae8563b25f73dc584a07bcda7a82750ff4f7672 ]
Using TX push when notifying the NIC of multiple new descriptors in
the ring will very occasionally cause the TX DMA engine to re-use an
old descriptor. This can result in a duplicated or partly duplicated
packet (new headers with old data), or an IOMMU page fault. This does
not happen when the pushed descriptor is the only one written.
TX push also provides little latency benefit when a packet requires
more than one descriptor.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 35205b211c8d17a8a0b5e8926cb7c73e9a7ef1ad ]
efx_device_detach_sync() locks all TX queues before marking the device
detached and thus disabling further TX scheduling. But it can still
be interrupted by TX completions which then result in TX scheduling in
soft interrupt context. This will deadlock when it tries to acquire
a TX queue lock that efx_device_detach_sync() already acquired.
To avoid deadlock, we must use netif_tx_{,un}lock_bh().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 29c69a4882641285a854d6d03ca5adbba68c0034 ]
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
The device is ready if all the following are true:
(a) It has a qdisc
(b) It is marked present
(c) It is running
(d) The link is reported up
(a) and (c) are normally true, and must not be changed by a driver.
(d) is under our control, but fake link changes may disturb userland.
This leaves (b). We already mark the device absent during reset
and self-test, but we need to do the same during MTU changes and ring
reallocation. We don't need to do this when the device is brought
down because then (c) is already false.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commits 06e63c57acbb1df7c35ebe846ae416a8b88dfafa,
b590ace09d51cd39744e0f7662c5e4a0d1b5d952 and
c73e787a8db9117d59b5180baf83203a42ecadca ]
We assume that the mapping between DMA and virtual addresses is done
on whole pages, so we can find the page offset of an RX buffer using
the lower bits of the DMA address. However, swiotlb maps in units of
2K, breaking this assumption.
Add an explicit page_offset field to struct efx_rx_buffer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 3a68f19d7afb80f548d016effbc6ed52643a8085 ]
We may currently allocate two RX DMA buffers to a page, and only unmap
the page when the second is completed. We do not sync the first RX
buffer to be completed; this can result in packet loss or corruption
if the last RX buffer completed in a NAPI poll is the first in a page
and is not DMA-coherent. (In the middle of a NAPI poll, we will
handle the following RX completion and unmap the page *before* looking
at the content of the first buffer.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit ebf98e797b4e26ad52ace1511a0b503ee60a6cd4 ]
efx_mcdi_poll() uses get_seconds() to read the current time and to
implement a polling timeout. The use of this function was chosen
partly because it could easily be replaced in a co-sim environment
with a macro that read the simulated time.
Unfortunately the real get_seconds() returns the system time (real
time) which is subject to adjustment by e.g. ntpd. If the system time
is adjusted forward during a polled MCDI operation, the effective
timeout can be shorter than the intended 10 seconds, resulting in a
spurious failure. It is also possible for a backward adjustment to
delay detection of a areal failure.
Use jiffies instead, and change MCDI_RPC_TIMEOUT to be denominated in
jiffies. Also correct rounding of the timeout: check time > finish
(or rather time_after(time, finish)) and not time >= finish.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit c2f3b8e3a44b6fe9e36704e30157ebe1a88c08b1 ]
The assertion of netif_device_present() at the top of
efx_hard_start_xmit() may fail if we don't do this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commits a606f4325dca6950996abbae452d33f2af095f39,
d5e8cc6c946e0857826dcfbb3585068858445bfe,
525d9e824018cd7cc8d8d44832ddcd363abfe6e1 ]
The TX DMA engine issues upstream read requests when there is room in
the TX FIFO for the completion. However, the fetches for the rest of
the packet might be delayed by any back pressure. Since a flush must
wait for an EOP, the entire flush may be delayed by back pressure.
Mitigate this by disabling flow control before the flushes are
started. Since PF and VF flushes run in parallel introduce
fc_disable, a reference count of the number of flushes outstanding.
The same principle could be applied to Falcon, but that
would bring with it its own testing.
We sometimes hit a "failed to flush" timeout on some TX queues, but the
flushes have completed and the flush completion events seem to go missing.
In this case, we can check the TX_DESC_PTR_TBL register and drain the
queues if the flushes had finished.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.2:
- Call efx_nic_type::finish_flush() on both success and failure paths
- Check the TX_DESC_PTR_TBL registers in the polling loop
- Declare efx_mcdi_set_mac() extern]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit bfeed902946a31692e7a24ed355b6d13ac37d014 ]
On big-endian systems the MTD partition names currently have mangled
subtype numbers and are not recognised by the firmware update tool
(sfupdate).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Backported to 3.2: use old macros for length of firmware subtype array]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 3dca9d2dc285faf1910d405b65df845cab061356 ]
efx_nic_fatal_interrupt() disables DMA before scheduling a reset.
After this, we need not and *cannot* flush queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 876254ae2758d50dcb08c7bd00caf6a806571178 ]
bond_update_speed_duplex() might sleep while calling underlying slave's
routines. Move it out of atomic context in bond_enslave() and remove it
from bond_miimon_commit() - it was introduced by commit 546add79, however
when the slave interfaces go up/change state it's their responsibility to
fire NETDEV_UP/NETDEV_CHANGE events so that bonding can properly update
their speed.
I've tested it on all combinations of ifup/ifdown, autoneg/speed/duplex
changes, remote-controlled and local, on (not) MII-based cards. All changes
are visible.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 3f315bef23075ea8a98a6fe4221a83b83456d970 ]
__netpoll_cleanup() is called in netconsole_netdev_event() while holding a
spinlock. Release/acquire the spinlock before/after it and restart the
loop. Also, disable the netconsole completely, because we won't have chance
after the restart of the loop, and might end up in a situation where
nt->enabled == 1 and nt->np.dev == NULL.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit cb29529ea0030e60ef1bbbf8399a43d397a51526 ]
If a machine has X (X < 4) sunsu ports and cmdline
option "console=ttySY" is passed, where X < Y <= 4,
than the following panic happens:
Unable to handle kernel NULL pointer dereference
TPC: <sunsu_console_setup+0x78/0xe0>
RPC: <sunsu_console_setup+0x74/0xe0>
I7: <register_console+0x378/0x3e0>
Call Trace:
[0000000000453a38] register_console+0x378/0x3e0
[0000000000576fa0] uart_add_one_port+0x2e0/0x340
[000000000057af40] su_probe+0x160/0x2e0
[00000000005b8a4c] platform_drv_probe+0xc/0x20
[00000000005b6c2c] driver_probe_device+0x12c/0x220
[00000000005b6da8] __driver_attach+0x88/0xa0
[00000000005b4df4] bus_for_each_dev+0x54/0xa0
[00000000005b5a54] bus_add_driver+0x154/0x260
[00000000005b7190] driver_register+0x50/0x180
[00000000006d250c] sunsu_init+0x18c/0x1e0
[00000000006c2668] do_one_initcall+0xe8/0x160
[00000000006c282c] kernel_init_freeable+0x12c/0x1e0
[0000000000603764] kernel_init+0x4/0x100
[0000000000405f64] ret_from_syscall+0x1c/0x2c
[0000000000000000] (null)
1)Fix the panic;
2)Increment registered port number every successful
probe.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 46aa92d1ba162b4b3d6b7102440e459d4e4ee255 upstream.
ubuf info allocator uses guest controlled head as an index,
so a malicious guest could put the same head entry in the ring twice,
and we will get two callbacks on the same value.
To fix use upend_idx which is guaranteed to be unique.
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 9437a248e7cac427c898bdb11bd1ac6844a1ead4 upstream.
The driver was failing to clear the BSSID when a disconnect happened. That
prevented a reconnection. This problem is reported at
https://bugzilla.redhat.com/show_bug.cgi?id=789605,
https://bugzilla.redhat.com/show_bug.cgi?id=866786,
https://bugzilla.redhat.com/show_bug.cgi?id=906734, and
https://bugzilla.kernel.org/show_bug.cgi?id=46171.
Thanks to Jussi Kivilinna for making the critical observation
that led to the solution.
Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 664899786cb49cb52f620e06ac19c0be524a7cfa upstream.
When run at debug 3 or higher, rtl8192cu reports a BUG as follows:
BUG: scheduling while atomic: kworker/u:0/5281/0x00000002
INFO: lockdep is turned off.
Modules linked in: rtl8192cu rtl8192c_common rtlwifi fuse af_packet bnep bluetooth b43 mac80211 cfg80211 ipv6 snd_hda_codec_conexant kvm_amd k
vm snd_hda_intel snd_hda_codec bcma rng_core snd_pcm ssb mmc_core snd_seq snd_timer snd_seq_device snd i2c_nforce2 sr_mod pcmcia forcedeth i2c_core soundcore
cdrom sg serio_raw k8temp hwmon joydev ac battery pcmcia_core snd_page_alloc video button wmi autofs4 ext4 mbcache jbd2 crc16 thermal processor scsi_dh_alua
scsi_dh_hp_sw scsi_dh_rdac scsi_dh_emc scsi_dh ata_generic pata_acpi pata_amd [last unloaded: rtlwifi]
Pid: 5281, comm: kworker/u:0 Tainted: G W 3.8.0-wl+ #119
Call Trace:
[<ffffffff814531e7>] __schedule_bug+0x62/0x70
[<ffffffff81459af0>] __schedule+0x730/0xa30
[<ffffffff81326e49>] ? usb_hcd_link_urb_to_ep+0x19/0xa0
[<ffffffff8145a0d4>] schedule+0x24/0x70
[<ffffffff814575ec>] schedule_timeout+0x18c/0x2f0
[<ffffffff81459ec0>] ? wait_for_common+0x40/0x180
[<ffffffff8133f461>] ? ehci_urb_enqueue+0xf1/0xee0
[<ffffffff810a579d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff81459f65>] wait_for_common+0xe5/0x180
[<ffffffff8107d1c0>] ? try_to_wake_up+0x2d0/0x2d0
[<ffffffff8145a08e>] wait_for_completion_timeout+0xe/0x10
[<ffffffff8132ab1c>] usb_start_wait_urb+0x8c/0x100
[<ffffffff8132adf9>] usb_control_msg+0xd9/0x130
[<ffffffffa057dd8d>] _usb_read_sync+0xcd/0x140 [rtlwifi]
[<ffffffffa057de0e>] _usb_read32_sync+0xe/0x10 [rtlwifi]
[<ffffffffa04b0555>] rtl92cu_update_hal_rate_table+0x1a5/0x1f0 [rtl8192cu]
The cause is a synchronous read from routine rtl92cu_update_hal_rate_table().
The resulting output is not critical, thus the debug statement is
deleted.
Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: the deleted code is slightly different]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5f0fabf84d7b52f979dcbafa3d3c530c60d9a92c upstream.
smatch found this error:
CHECK drivers/net/wireless/mwifiex/join.c
drivers/net/wireless/mwifiex/join.c:1121
mwifiex_cmd_802_11_ad_hoc_join()
error: testing array offset 'i' after use.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d627b62ff8d4d36761adbcd90ff143d79c94ab22 upstream.
This is rather a hack to fix brightness hotkeys on a Clevo laptop. CADL is not
used anywhere in the driver code at the moment, but it could be used in BIOS as
is the case with the Clevo laptop.
The Clevo B7130 requires the CADL field to contain at least the ID of
the LCD device. If this field is empty, the ACPI methods that are called
on pressing brightness / display switching hotkeys will not trigger a
notification. As a result, it appears as no hotkey has been pressed.
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=45452
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 0920a48719f1ceefc909387a64f97563848c7854 upstream.
This increases GEN6_RC6p_THRESHOLD from 100000 to 150000. For some
reason this avoids the gen6_gt_check_fifodbg.isra warnings and
associated GPU lockups, which makes my ivy bridge machine stable.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit 87ab7f6f2874f1115817e394a7ed2dea1c72549e ]
Macvlan already supports hw address filters. Set the IFF_UNICAST_FLT
so that it doesn't needlesly enter PROMISC mode when macvlans are
stacked.
Signed-of-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
[ Upstream commit f8af75f3517a24838a36eb5797a1a3e60bf9e276 ]
Dave reported following crash :
general protection fault: 0000 [#1] SMP
CPU 2
Pid: 25407, comm: qemu-kvm Not tainted 3.7.9-205.fc18.x86_64 #1 Hewlett-Packard HP Z400 Workstation/0B4Ch
RIP: 0010:[<ffffffffa0399bd5>] [<ffffffffa0399bd5>] destroy_conntrack+0x35/0x120 [nf_conntrack]
RSP: 0018:ffff880276913d78 EFLAGS: 00010206
RAX: 50626b6b7876376c RBX: ffff88026e530d68 RCX: ffff88028d158e00
RDX: ffff88026d0d5470 RSI: 0000000000000011 RDI: 0000000000000002
RBP: ffff880276913d88 R08: 0000000000000000 R09: ffff880295002900
R10: 0000000000000000 R11: 0000000000000003 R12: ffffffff81ca3b40
R13: ffffffff8151a8e0 R14: ffff880270875000 R15: 0000000000000002
FS: 00007ff3bce38a00(0000) GS:ffff88029fc40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007fd1430bd000 CR3: 000000027042b000 CR4: 00000000000027e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process qemu-kvm (pid: 25407, threadinfo ffff880276912000, task ffff88028c369720)
Stack:
ffff880156f59100 ffff880156f59100 ffff880276913d98 ffffffff815534f7
ffff880276913db8 ffffffff8151a74b ffff880270875000 ffff880156f59100
ffff880276913dd8 ffffffff8151a5a6 ffff880276913dd8 ffff88026d0d5470
Call Trace:
[<ffffffff815534f7>] nf_conntrack_destroy+0x17/0x20
[<ffffffff8151a74b>] skb_release_head_state+0x7b/0x100
[<ffffffff8151a5a6>] __kfree_skb+0x16/0xa0
[<ffffffff8151a666>] kfree_skb+0x36/0xa0
[<ffffffff8151a8e0>] skb_queue_purge+0x20/0x40
[<ffffffffa02205f7>] __tun_detach+0x117/0x140 [tun]
[<ffffffffa022184c>] tun_chr_close+0x3c/0xd0 [tun]
[<ffffffff8119669c>] __fput+0xec/0x240
[<ffffffff811967fe>] ____fput+0xe/0x10
[<ffffffff8107eb27>] task_work_run+0xa7/0xe0
[<ffffffff810149e1>] do_notify_resume+0x71/0xb0
[<ffffffff81640152>] int_signal+0x12/0x17
Code: 00 00 04 48 89 e5 41 54 53 48 89 fb 4c 8b a7 e8 00 00 00 0f 85 de 00 00 00 0f b6 73 3e 0f b7 7b 2a e8 10 40 00 00 48 85 c0 74 0e <48> 8b 40 28 48 85 c0 74 05 48 89 df ff d0 48 c7 c7 08 6a 3a a0
RIP [<ffffffffa0399bd5>] destroy_conntrack+0x35/0x120 [nf_conntrack]
RSP <ffff880276913d78>
This is because tun_net_xmit() needs to call nf_reset()
before queuing skb into receive_queue
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b81273a132177edd806476b953f6afeb17b786d5 upstream.
Now that login from util-linux is forced to drop all references to a
TTY which it wants to hangup (to reach reference count 1) we are
seeing issues with telnet. When login closes its last reference to the
slave PTY, it also resets packet mode on the *master* side. And we
have a race here.
What telnet does is fork+exec of `login'. Then there are two
scenarios:
* `login' closes the slave TTY and resets thus master's packet mode,
but even now telnet properly sets the mode, or
* `telnetd' sets packet mode on the master, `login' closes the slave
TTY and resets master's packet mode.
The former case is OK. However the latter happens in much more cases,
by the order of magnitude to be precise. So when one tries to login to
such a messed telnet setup, they see the following:
inux login:
ogin incorrect
Note the missing first letters -- telnet thinks it is still in the
packet mode, so when it receives "linux login" from `login', it
considers "l" as the type of the packet and strips it.
SuS does not mention how the implementation should behave. Both BSDs I
checked (Free and Net) do not reset the flag upon the last close.
By this I am resurrecting an old bug, see References. We are hitting
it regularly now, i.e. with updated util-linux, ergo login.
Here, I am changing a behavior introduced back in 2.1 times. It would
better have a long time testing before goes upstream.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Bryan Mason <bmason@redhat.com>
References: https://lkml.org/lkml/2009/11/11/223
References: https://bugzilla.redhat.com/show_bug.cgi?id=504703
References: https://bugzilla.novell.com/show_bug.cgi?id=797042
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 0720a06a7518c9d0c0125bd5d1f3b6264c55c3dd upstream.
The utf8s_to_utf16s conversion routine needs to be improved. Unlike
its utf16s_to_utf8s sibling, it doesn't accept arguments specifying
the maximum length of the output buffer or the endianness of its
16-bit output.
This patch (as1501) adds the two missing arguments, and adjusts the
only two places in the kernel where the function is called. A
follow-on patch will add a third caller that does utilize the new
capabilities.
The two conversion routines are still annoyingly inconsistent in the
way they handle invalid byte combinations. But that's a subject for a
different patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit b1a6650406875b9097a032eed89af50682fe1160 upstream.
When loopdev is built as module and we pass an invalid parameter,
loop_init() will return directly without deregister misc device, which
will cause an oops when insert loop module next time because we left some
garbage in the misc device list.
Test case:
sudo modprobe loop max_part=1024
(failed due to invalid parameter)
sudo modprobe loop
(oops)
Clean up nicely to avoid such oops.
Signed-off-by: Guo Chao <yan@linux.vnet.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Guo Chao <yan@linux.vnet.ibm.com>
Cc: M. Hindess <hindessm@uk.ibm.com>
Cc: Nikanth Karthikesan <knikanth@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 5370019dc2d2c2ff90e95d181468071362934f3a upstream.
bd_mutex and lo_ctl_mutex can be held in different order.
Path #1:
blkdev_open
blkdev_get
__blkdev_get (hold bd_mutex)
lo_open (hold lo_ctl_mutex)
Path #2:
blkdev_ioctl
lo_ioctl (hold lo_ctl_mutex)
lo_set_capacity (hold bd_mutex)
Lockdep does not report it, because path #2 actually holds a subclass of
lo_ctl_mutex. This subclass seems creep into the code by mistake. The
patch author actually just mentioned it in the changelog, see commit
f028f3b2 ("loop: fix circular locking in loop_clr_fd()"), also see:
http://marc.info/?l=linux-kernel&m=123806169129727&w=2
Path #2 hold bd_mutex to call bd_set_size(), I've protected it
with i_mutex in a previous patch, so drop bd_mutex at this site.
Signed-off-by: Guo Chao <yan@linux.vnet.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Guo Chao <yan@linux.vnet.ibm.com>
Cc: M. Hindess <hindessm@uk.ibm.com>
Cc: Nikanth Karthikesan <knikanth@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 08e34eb14fe4cfd934b5c169a7682a969457c4ea upstream.
After a guest is live migrated, the xen-netfront driver emits a gratuitous
ARP message, so that networking hardware on the target host's subnet can
take notice, and public routing to the guest is re-established. However,
if the packet appears on the backend interface before the backend is added
to the target host's bridge, the packet is lost, and the migrated guest's
peers become unable to talk to the guest.
A sufficient two-parts condition to prevent the above is:
(1) ensure that the backend only moves to Connected xenbus state after its
hotplug scripts completed, ie. the netback interface got added to the
bridge; and
(2) ensure the frontend only queues the gARP when it sees the backend move
to Connected.
These two together provide complete ordering. Sub-condition (1) is already
satisfied by commit f942dc2552b8 in Linus' tree, based on commit
6b0b80ca7165 from [1].
In general, the full condition is sufficient, not necessary, because,
according to [2], live migration has been working for a long time without
satisfying sub-condition (2). However, after 6b0b80ca7165 was backported
to the RHEL-5 host to ensure (1), (2) still proved necessary in the RHEL-6
guest. This patch intends to provide (2) for upstream.
The Reviewed-by line comes from [3].
[1] git://xenbits.xen.org/people/ianc/linux-2.6.git#upstream/dom0/backend/netback-history
[2] http://old-list-archives.xen.org/xen-devel/2011-06/msg01969.html
[3] http://old-list-archives.xen.org/xen-devel/2011-07/msg00484.html
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit d3b9d7a9051d7024a93c76a84b2f84b3b66ad6d5 upstream.
A USB 3.0 device can transition to the Inactive state if a U1 or U2 exit
transition fails. The current code in hub_events simply issues a warm
reset, but does not call any pre-reset or post-reset driver methods (or
unbind/rebind drivers without them). Therefore the drivers won't know
their device has just been reset.
hub_events should instead call usb_reset_device. This means
hub_port_reset now needs to figure out whether it should issue a warm
reset or a hot reset.
Remove the FIXME note about needing disconnect() for a NOTATTACHED
device. This patch fixes that.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit a24a6078754f28528bc91e7e7b3e6ae86bd936d8 upstream.
When a hot reset fails on a USB 3.0 port, the current port reset code
recursively calls hub_port_reset inside hub_port_wait_reset. This isn't
ideal, since we should avoid recursive calls in the kernel, and it also
doesn't allow us to issue multiple warm resets on reset failures.
Rip out the recursive call. Instead, add code to hub_port_reset to
issue a warm reset if the hot reset fails, and try multiple warm resets
before giving up on the port.
In hub_port_wait_reset, remove the recursive call and re-indent. The
code is basically the same, except:
1. It bails out early if the port has transitioned to Inactive or
Compliance Mode after the reset completed.
2. It doesn't consider a connect status change to be a failed reset. If
multiple warm resets needed to be issued, the connect status may have
changed, so we need to ignore that and look at the port link state
instead. hub_port_reset will now do that.
3. It unconditionally sets udev->speed on all types of successful
resets. The old recursive code would set the port speed when the second
hub_port_reset returned.
The old code did not handle connected devices needing a warm reset well.
There were only two situations that the old code handled correctly: an
empty port needing a warm reset, and a hot reset that migrated to a warm
reset.
When an empty port needed a warm reset, hub_port_reset was called with
the warm variable set. The code in hub_port_finish_reset would skip
telling the USB core and the xHC host that the device was reset, because
otherwise that would result in a NULL pointer dereference.
When a USB 3.0 device reset migrated to a warm reset, the recursive call
made the call stack look like this:
hub_port_reset(warm = false)
hub_wait_port_reset(warm = false)
hub_port_reset(warm = true)
hub_wait_port_reset(warm = true)
hub_port_finish_reset(warm = true)
(return up the call stack to the first wait)
hub_port_finish_reset(warm = false)
The old code didn't want to notify the USB core or the xHC host of device reset
twice, so it only did it in the second call to hub_port_finish_reset,
when warm was set to false. This was necessary because
before patch two ("USB: Ignore xHCI Reset Device status."), the USB core
would pay attention to the xHC Reset Device command error status, and
the second call would always fail.
Now that we no longer have the recursive call, and warm can change from
false to true in hub_port_reset, we need to have hub_port_finish_reset
unconditionally notify the USB core and the xHC of the device reset.
In hub_port_finish_reset, unconditionally clear the connect status
change (CSC) bit for USB 3.0 hubs when the port reset is done. If we
had to issue multiple warm resets for a device, that bit may have been
set if the device went into SS.Inactive and then was successfully warm
reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
|
commit 2d4fa940f99663c82ba55b2244638833b388e4e2 upstream.
The next patch will refactor the hub port code to rip out the recursive
call to hub_port_reset on a failed hot reset. In preparation for that,
make sure all code paths can deal with being called with a NULL udev.
The usb_device will not be valid if warm reset was issued because a port
transitioned to the Inactive or Compliance Mode on a device connect.
This patch should have no effect on current behavior.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
|
