summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2015-10-01Revert "iio: bmg160: IIO_BUFFER and IIO_TRIGGERED_BUFFER are required"Markus Pargmann
This reverts commit 35c45e8bce3c92fb1ff94d376f1d4bfaae079d66 which was commit 06d2f6ca5a38abe92f1f3a132b331eee773868c3 upstream as it should not have been applied. Reported-by: Luis Henriques <luis.henriques@canonical.com> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01usbnet: Get EVENT_NO_RUNTIME_PM bit before it is clearedEugene Shatokhin
[ Upstream commit f50791ac1aca1ac1b0370d62397b43e9f831421a ] It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in usbnet_stop(), but its value should be read before it is cleared when dev->flags is set to 0. The problem was spotted and the fix was provided by Oliver Neukum <oneukum@suse.de>. Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01bonding: fix destruction of bond with devices different from arphrd_etherNikolay Aleksandrov
[ Upstream commit 06f6d1094aa0992432b1e2a0920b0ee86ccd83bf ] When the bonding is being unloaded and the netdevice notifier is unregistered it executes NETDEV_UNREGISTER for each device which should remove the bond's proc entry but if the device enslaved is not of ARPHRD_ETHER type and is in front of the bonding, it may execute bond_release_and_destroy() first which would release the last slave and destroy the bond device leaving the proc entry and thus we will get the following error (with dynamic debug on for bond_netdev_event to see the events order): [ 908.963051] eql: event: 9 [ 908.963052] eql: IFF_SLAVE [ 908.963054] eql: event: 2 [ 908.963056] eql: IFF_SLAVE [ 908.963058] eql: event: 6 [ 908.963059] eql: IFF_SLAVE [ 908.963110] bond0: Releasing active interface eql [ 908.976168] bond0: Destroying bond bond0 [ 908.976266] bond0 (unregistering): Released all slaves [ 908.984097] ------------[ cut here ]------------ [ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575 remove_proc_entry+0x112/0x160() [ 908.984110] remove_proc_entry: removing non-empty directory 'net/bonding', leaking at least 'bond0' [ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore usb_common [last unloaded: bonding] [ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O 4.2.0-rc2+ #8 [ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34 ffff8800358dfda8 [ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40 ffff88003e3a4280 [ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a ffffffff8172ebd0 [ 908.984181] Call Trace: [ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50 [ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0 [ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50 [ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160 [ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30 [bonding] [ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding] [ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70 [ 908.984225] [<ffffffff8142f52d>] ? unregister_pernet_operations+0x8d/0xd0 [ 908.984228] [<ffffffff8142f58d>] ? unregister_pernet_subsys+0x1d/0x30 [ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding] [ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250 [ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0 [ 908.984244] [<ffffffff8152b732>] ? entry_SYSCALL_64_fastpath+0x16/0x75 [ 908.984247] ---[ end trace 7c006ed4abbef24b ]--- Thus remove the proc entry manually if bond_release_and_destroy() is used. Because of the checks in bond_remove_proc_entry() it's not a problem for a bond device to change namespaces (the bug fixed by the Fixes commit) but since commit f9399814927ad ("bonding: Don't allow bond devices to change network namespaces.") that can't happen anyway. Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Fixes: a64d49c3dd50 ("bonding: Manage /proc/net/bonding/ entries from the netdev events") Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01isdn/gigaset: reset tty->receive_room when attaching ser_gigasetTilman Schmidt
[ Upstream commit fd98e9419d8d622a4de91f76b306af6aa627aa9c ] Commit 79901317ce80 ("n_tty: Don't flush buffer when closing ldisc"), first merged in kernel release 3.10, caused the following regression in the Gigaset M101 driver: Before that commit, when closing the N_TTY line discipline in preparation to switching to N_GIGASET_M101, receive_room would be reset to a non-zero value by the call to n_tty_flush_buffer() in n_tty's close method. With the removal of that call, receive_room might be left at zero, blocking data reception on the serial line. The present patch fixes that regression by setting receive_room to an appropriate value in the ldisc open method. Fixes: 79901317ce80 ("n_tty: Don't flush buffer when closing ldisc") Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01vhost/scsi: potential memory corruptionDan Carpenter
commit 59c816c1f24df0204e01851431d3bab3eb76719c upstream. This code in vhost_scsi_make_tpg() is confusing because we limit "tpgt" to UINT_MAX but the data type of "tpg->tport_tpgt" and that is a u16. I looked at the context and it turns out that in vhost_scsi_set_endpoint(), "tpg->tport_tpgt" is used as an offset into the vs_tpg[] array which has VHOST_SCSI_MAX_TARGET (256) elements so anything higher than 255 then it is invalid. I have made that the limit now. In vhost_scsi_send_evt() we mask away values higher than 255, but now that the limit has changed, we don't need the mask. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> [ The affected function was renamed to vhost_scsi_make_tpg before the vulnerability was announced, I ported it to 3.10 stable and changed the code in function tcm_vhost_make_tpg] Signed-off-by: Wang Long <long.wanglong@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01IB/mlx4: Use correct SL on AH query under RoCENoa Osherovich
commit 5e99b139f1b68acd65e36515ca347b03856dfb5a upstream. The mlx4 IB driver implementation for ib_query_ah used a wrong offset (28 instead of 29) when link type is Ethernet. Fixed to use the correct one. Fixes: fa417f7b520e ('IB/mlx4: Add support for IBoE') Signed-off-by: Shani Michaeli <shanim@mellanox.com> Signed-off-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01IB/mlx4: Forbid using sysfs to change RoCE pkeysJack Morgenstein
commit 2b135db3e81301d0452e6aa107349abe67b097d6 upstream. The pkey mapping for RoCE must remain the default mapping: VFs: virtual index 0 = mapped to real index 0 (0xFFFF) All others indices: mapped to a real pkey index containing an invalid pkey. PF: virtual index i = real index i. Don't allow users to change these mappings using files found in sysfs. Fixes: c1e7e466120b ('IB/mlx4: Add iov directory in sysfs under the ib device') Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01IB/uverbs: Fix race between ib_uverbs_open and remove_oneYishai Hadas
commit 35d4a0b63dc0c6d1177d4f532a9deae958f0662c upstream. Fixes: 2a72f212263701b927559f6850446421d5906c41 ("IB/uverbs: Remove dev_table") Before this commit there was a device look-up table that was protected by a spin_lock used by ib_uverbs_open and by ib_uverbs_remove_one. When it was dropped and container_of was used instead, it enabled the race with remove_one as dev might be freed just after: dev = container_of(inode->i_cdev, struct ib_uverbs_device, cdev) but before the kref_get. In addition, this buggy patch added some dead code as container_of(x,y,z) can never be NULL and so dev can never be NULL. As a result the comment above ib_uverbs_open saying "the open method will either immediately run -ENXIO" is wrong as it can never happen. The solution follows Jason Gunthorpe suggestion from below URL: https://www.mail-archive.com/linux-rdma@vger.kernel.org/msg25692.html cdev will hold a kref on the parent (the containing structure, ib_uverbs_device) and only when that kref is released it is guaranteed that open will never be called again. In addition, fixes the active count scheme to use an atomic not a kref to prevent WARN_ON as pointed by above comment from Jason. Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Shachar Raindel <raindel@mellanox.com> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01IB/uverbs: reject invalid or unknown opcodesChristoph Hellwig
commit b632ffa7cee439ba5dce3b3bc4a5cbe2b3e20133 upstream. We have many WR opcodes that are only supported in kernel space and/or require optional information to be copied into the WR structure. Reject all those not explicitly handled so that we can't pass invalid information to drivers. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01xen/gntdev: convert priv->lock to a mutexDavid Vrabel
commit 1401c00e59ea021c575f74612fe2dbba36d6a4ee upstream. Unmapping may require sleeping and we unmap while holding priv->lock, so convert it to a mutex. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01md/raid10: always set reshape_safe when initializing reshape_position.NeilBrown
commit 299b0685e31c9f3dcc2d58ee3beca761a40b44b3 upstream. 'reshape_position' tracks where in the reshape we have reached. 'reshape_safe' tracks where in the reshape we have safely recorded in the metadata. These are compared to determine when to update the metadata. So it is important that reshape_safe is initialised properly. Currently it isn't. When starting a reshape from the beginning it usually has the correct value by luck. But when reducing the number of devices in a RAID10, it has the wrong value and this leads to the metadata not being updated correctly. This can lead to corruption if the reshape is not allowed to complete. This patch is suitable for any -stable kernel which supports RAID10 reshape, which is 3.5 and later. Fixes: 3ea7daa5d7fd ("md/raid10: add reshape support") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01mmc: core: fix race condition in mmc_wait_data_doneJialing Fu
commit 71f8a4b81d040b3d094424197ca2f1bf811b1245 upstream. The following panic is captured in ker3.14, but the issue still exists in latest kernel. --------------------------------------------------------------------- [ 20.738217] c0 3136 (Compiler) Unable to handle kernel NULL pointer dereference at virtual address 00000578 ...... [ 20.738499] c0 3136 (Compiler) PC is at _raw_spin_lock_irqsave+0x24/0x60 [ 20.738527] c0 3136 (Compiler) LR is at _raw_spin_lock_irqsave+0x20/0x60 [ 20.740134] c0 3136 (Compiler) Call trace: [ 20.740165] c0 3136 (Compiler) [<ffffffc0008ee900>] _raw_spin_lock_irqsave+0x24/0x60 [ 20.740200] c0 3136 (Compiler) [<ffffffc0000dd024>] __wake_up+0x1c/0x54 [ 20.740230] c0 3136 (Compiler) [<ffffffc000639414>] mmc_wait_data_done+0x28/0x34 [ 20.740262] c0 3136 (Compiler) [<ffffffc0006391a0>] mmc_request_done+0xa4/0x220 [ 20.740314] c0 3136 (Compiler) [<ffffffc000656894>] sdhci_tasklet_finish+0xac/0x264 [ 20.740352] c0 3136 (Compiler) [<ffffffc0000a2b58>] tasklet_action+0xa0/0x158 [ 20.740382] c0 3136 (Compiler) [<ffffffc0000a2078>] __do_softirq+0x10c/0x2e4 [ 20.740411] c0 3136 (Compiler) [<ffffffc0000a24bc>] irq_exit+0x8c/0xc0 [ 20.740439] c0 3136 (Compiler) [<ffffffc00008489c>] handle_IRQ+0x48/0xac [ 20.740469] c0 3136 (Compiler) [<ffffffc000081428>] gic_handle_irq+0x38/0x7c ---------------------------------------------------------------------- Because in SMP, "mrq" has race condition between below two paths: path1: CPU0: <tasklet context> static void mmc_wait_data_done(struct mmc_request *mrq) { mrq->host->context_info.is_done_rcv = true; // // If CPU0 has just finished "is_done_rcv = true" in path1, and at // this moment, IRQ or ICache line missing happens in CPU0. // What happens in CPU1 (path2)? // // If the mmcqd thread in CPU1(path2) hasn't entered to sleep mode: // path2 would have chance to break from wait_event_interruptible // in mmc_wait_for_data_req_done and continue to run for next // mmc_request (mmc_blk_rw_rq_prep). // // Within mmc_blk_rq_prep, mrq is cleared to 0. // If below line still gets host from "mrq" as the result of // compiler, the panic happens as we traced. wake_up_interruptible(&mrq->host->context_info.wait); } path2: CPU1: <The mmcqd thread runs mmc_queue_thread> static int mmc_wait_for_data_req_done(... { ... while (1) { wait_event_interruptible(context_info->wait, (context_info->is_done_rcv || context_info->is_new_req)); static void mmc_blk_rw_rq_prep(... { ... memset(brq, 0, sizeof(struct mmc_blk_request)); This issue happens very coincidentally; however adding mdelay(1) in mmc_wait_data_done as below could duplicate it easily. static void mmc_wait_data_done(struct mmc_request *mrq) { mrq->host->context_info.is_done_rcv = true; + mdelay(1); wake_up_interruptible(&mrq->host->context_info.wait); } At runtime, IRQ or ICache line missing may just happen at the same place of the mdelay(1). This patch gets the mmc_context_info at the beginning of function, it can avoid this race condition. Signed-off-by: Jialing Fu <jlfu@marvell.com> Tested-by: Shawn Lin <shawn.lin@rock-chips.com> Fixes: 2220eedfd7ae ("mmc: fix async request mechanism ....") Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01rc-core: fix remove uevent generationDavid Härdeman
commit a66b0c41ad277ae62a3ae6ac430a71882f899557 upstream. The input_dev is already gone when the rc device is being unregistered so checking for its presence only means that no remove uevent will be generated. Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01Add radeon suspend/resume quirk for HP Compaq dc5750.Jeffery Miller
commit 09bfda10e6efd7b65bcc29237bee1765ed779657 upstream. With the radeon driver loaded the HP Compaq dc5750 Small Form Factor machine fails to resume from suspend. Adding a quirk similar to other devices avoids the problem and the system resumes properly. Signed-off-by: Jeffery Miller <jmiller@neverware.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01tg3: Fix temperature reportingJean Delvare
commit d3d11fe08ccc9bff174fc958722b5661f0932486 upstream. The temperature registers appear to report values in degrees Celsius while the hwmon API mandates values to be exposed in millidegrees Celsius. Do the conversion so that the values reported by "sensors" are correct. Fixes: aed93e0bf493 ("tg3: Add hwmon support for temperature") Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Prashant Sreedharan <prashant@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-01rtlwifi: rtl8192cu: Add new device IDAdrien Schildknecht
commit 1642d09fb9b128e8e538b2a4179962a34f38dff9 upstream. The v2 of NetGear WNA1000M uses a different idProduct: USB ID 0846:9043 Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21drivercore: Fix unregistration path of platform devicesGrant Likely
commit 7f5dcaf1fdf289767a126a0a5cc3ef39b5254b06 upstream. The unregister path of platform_device is broken. On registration, it will register all resources with either a parent already set, or type==IORESOURCE_{IO,MEM}. However, on unregister it will release everything with type==IORESOURCE_{IO,MEM}, but ignore the others. There are also cases where resources don't get registered in the first place, like with devices created by of_platform_populate()*. Fix the unregister path to be symmetrical with the register path by checking the parent pointer instead of the type field to decide which resources to unregister. This is safe because the upshot of the registration path algorithm is that registered resources have a parent pointer, and non-registered resources do not. * It can be argued that of_platform_populate() should be registering it's resources, and they argument has some merit. However, there are quite a few platforms that end up broken if we try to do that due to overlapping resources in the device tree. Until that is fixed, we need to solve the immediate problem. Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: Rob Herring <robh@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Grant Likely <grant.likely@linaro.org> Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21of/address: Don't loop forever in of_find_matching_node_by_address().David Daney
commit 3a496b00b6f90c41bd21a410871dfc97d4f3c7ab upstream. If the internal call to of_address_to_resource() fails, we end up looping forever in of_find_matching_node_by_address(). This can be caused by a defective device tree, or calling with an incorrect matches argument. Fix by calling of_find_matching_node() unconditionally at the end of the loop. Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21auxdisplay: ks0108: fix refcountSudip Mukherjee
commit bab383de3b84e584b0f09227151020b2a43dc34c upstream. parport_find_base() will implicitly do parport_get_port() which increases the refcount. Then parport_register_device() will again increment the refcount. But while unloading the module we are only doing parport_unregister_device() decrementing the refcount only once. We add an parport_put_port() to neutralize the effect of parport_get_port(). Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21devres: fix devres_get()Masahiro Yamada
commit 64526370d11ce8868ca495723d595b61e8697fbf upstream. Currently, devres_get() passes devres_free() the pointer to devres, but devres_free() should be given with the pointer to resource data. Fixes: 9ac7849e35f7 ("devres: device resource management") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21HID: usbhid: Fix the check for HID_RESET_PENDING in hid_io_errorDon Zickus
commit 3af4e5a95184d6d3c1c6a065f163faa174a96a1d upstream. It was reported that after 10-20 reboots, a usb keyboard plugged into a docking station would not work unless it was replugged in. Using usbmon, it turns out the interrupt URBs were streaming with callback errors of -71 for some reason. The hid-core.c::hid_io_error was supposed to retry and then reset, but the reset wasn't really happening. The check for HID_NO_BANDWIDTH was inverted. Fix was simple. Tested by reporter and locally by me by unplugging a keyboard halfway until I could recreate a stream of errors but no disconnect. Signed-off-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21serial: 8250: don't bind to SMSC IrCC IR portMaciej S. Szmigiero
commit ffa34de03bcfbfa88d8352942bc238bb48e94e2d upstream. SMSC IrCC SIR/FIR port should not be bound to by (legacy) serial driver so its own driver (smsc-ircc2) can bind to it. Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21usb: host: ehci-sys: delete useless bus_to_hcd conversionPeter Chen
commit 0521cfd06e1ebcd575e7ae36aab068b38df23850 upstream. The ehci platform device's drvdata is the pointer of struct usb_hcd already, so we doesn't need to call bus_to_hcd conversion again. Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21usb: dwc3: ep0: Fix mem corruption on OUT transfers of more than 512 bytesKishon Vijay Abraham I
commit b2fb5b1a0f50d3ebc12342c8d8dead245e9c9d4e upstream. DWC3 uses bounce buffer to handle non max packet aligned OUT transfers and the size of bounce buffer is 512 bytes. However if the host initiates OUT transfers of size more than 512 bytes (and non max packet aligned), the driver throws a WARN dump but still programs the TRB to receive more than 512 bytes. This will cause bounce buffer to overflow and corrupt the adjacent memory locations which can be fatal. Fix it by programming the TRB to receive a maximum of DWC3_EP0_BOUNCE_SIZE (512) bytes. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21USB: ftdi_sio: Added custom PID for CustomWare productsMatthijs Kooijman
commit 1fb8dc36384ae1140ee6ccc470de74397606a9d5 upstream. CustomWare uses the FTDI VID with custom PIDs for their ShipModul MiniPlex products. Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21USB: symbolserial: Use usb_get_serial_port_dataPhilipp Hachtmann
commit 951d3793bbfc0a441d791d820183aa3085c83ea9 upstream. The driver used usb_get_serial_data(port->serial) which compiled but resulted in a NULL pointer being returned (and subsequently used). I did not go deeper into this but I guess this is a regression. Signed-off-by: Philipp Hachtmann <hachti@hachti.de> Fixes: a85796ee5149 ("USB: symbolserial: move private-data allocation to port_probe") Acked-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21PCI: Fix TI816X class code quirkBjorn Helgaas
commit d1541dc977d376406f4584d8eb055488655c98ec upstream. In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO". But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class and needs to be shifted to make space for the low-order interface byte. Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code. Fixes: 63c4408074cb ("PCI: Add quirk for setting valid class for TI816X Endpoint") Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Hemant Pedanekar <hemantp@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21clk: versatile: off by one in clk_sp810_timerclken_of_get()Dan Carpenter
commit 3294bee87091be5f179474f6c39d1d87769635e2 upstream. The ">" should be ">=" or we end up reading beyond the end of the array. Fixes: 6e973d2c4385 ('clk: vexpress: Add separate SP810 driver') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21iio: adis16480: Fix scale factorsLars-Peter Clausen
commit 7abad1063deb0f77d275c61f58863ec319c58c5c upstream. The different devices support by the adis16480 driver have slightly different scales for the gyroscope and accelerometer channels. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21iio: bmg160: IIO_BUFFER and IIO_TRIGGERED_BUFFER are requiredMarkus Pargmann
commit 06d2f6ca5a38abe92f1f3a132b331eee773868c3 upstream. This patch adds selects for IIO_BUFFER and IIO_TRIGGERED_BUFFER. Without IIO_BUFFER, the driver does not compile. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-21DRM - radeon: Don't link train DisplayPort on HPD until we get the dpcdStephen Chandler Paul
commit 924f92bf12bfbef3662619e3ed24a1cea7c1cbcd upstream. Most of the time this isn't an issue since hotplugging an adaptor will trigger a crtc mode change which in turn, causes the driver to probe every DisplayPort for a dpcd. However, in cases where hotplugging doesn't cause a mode change (specifically when one unplugs a monitor from a DisplayPort connector, then plugs that same monitor back in seconds later on the same port without any other monitors connected), we never probe for the dpcd before starting the initial link training. What happens from there looks like this: - GPU has only one monitor connected. It's connected via DisplayPort, and does not go through an adaptor of any sort. - User unplugs DisplayPort connector from GPU. - Change in HPD is detected by the driver, we probe every DisplayPort for a possible connection. - Probe the port the user originally had the monitor connected on for it's dpcd. This fails, and we clear the first (and only the first) byte of the dpcd to indicate we no longer have a dpcd for this port. - User plugs the previously disconnected monitor back into the same DisplayPort. - radeon_connector_hotplug() is called before everyone else, and tries to handle the link training. Since only the first byte of the dpcd is zeroed, the driver is able to complete link training but does so against the wrong dpcd, causing it to initialize the link with the wrong settings. - Display stays blank (usually), dpcd is probed after the initial link training, and the driver prints no obvious messages to the log. In theory, since only one byte of the dpcd is chopped off (specifically, the byte that contains the revision information for DisplayPort), it's not entirely impossible that this bug may not show on certain monitors. For instance, the only reason this bug was visible on my ASUS PB238 monitor was due to the fact that this monitor using the enhanced framing symbol sequence, the flag for which is ignored if the radeon driver thinks that the DisplayPort version is below 1.1. Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-13crypto: caam - fix memory corruption in ahash_final_ctxHoria Geant?
commit b310c178e6d897f82abb9da3af1cd7c02b09f592 upstream. When doing pointer operation for accessing the HW S/G table, a value representing number of entries (and not number of bytes) must be used. Fixes: 045e36780f115 ("crypto: caam - ahash hmac support") Signed-off-by: Horia Geant? <horia.geanta@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-13libfc: Fix fc_fcp_cleanup_each_cmd()Bart Van Assche
commit 8f2777f53e3d5ad8ef2a176a4463a5c8e1a16431 upstream. Since fc_fcp_cleanup_cmd() can sleep this function must not be called while holding a spinlock. This patch avoids that fc_fcp_cleanup_each_cmd() triggers the following bug: BUG: scheduling while atomic: sg_reset/1512/0x00000202 1 lock held by sg_reset/1512: #0: (&(&fsp->scsi_pkt_lock)->rlock){+.-...}, at: [<ffffffffc0225cd5>] fc_fcp_cleanup_each_cmd.isra.21+0xa5/0x150 [libfc] Preemption disabled at:[<ffffffffc0225cd5>] fc_fcp_cleanup_each_cmd.isra.21+0xa5/0x150 [libfc] Call Trace: [<ffffffff816c612c>] dump_stack+0x4f/0x7b [<ffffffff810828bc>] __schedule_bug+0x6c/0xd0 [<ffffffff816c87aa>] __schedule+0x71a/0xa10 [<ffffffff816c8ad2>] schedule+0x32/0x80 [<ffffffffc0217eac>] fc_seq_set_resp+0xac/0x100 [libfc] [<ffffffffc0218b11>] fc_exch_done+0x41/0x60 [libfc] [<ffffffffc0225cff>] fc_fcp_cleanup_each_cmd.isra.21+0xcf/0x150 [libfc] [<ffffffffc0225f43>] fc_eh_device_reset+0x1c3/0x270 [libfc] [<ffffffff814a2cc9>] scsi_try_bus_device_reset+0x29/0x60 [<ffffffff814a3908>] scsi_ioctl_reset+0x258/0x2d0 [<ffffffff814a2650>] scsi_ioctl+0x150/0x440 [<ffffffff814b3a9d>] sd_ioctl+0xad/0x120 [<ffffffff8132f266>] blkdev_ioctl+0x1b6/0x810 [<ffffffff811da608>] block_ioctl+0x38/0x40 [<ffffffff811b4e08>] do_vfs_ioctl+0x2f8/0x530 [<ffffffff811b50c1>] SyS_ioctl+0x81/0xa0 [<ffffffff816cf8b2>] system_call_fastpath+0x16/0x7a Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-13EDAC, ppc4xx: Access mci->csrows array elements properlyMichael Walle
commit 5c16179b550b9fd8114637a56b153c9768ea06a5 upstream. The commit de3910eb79ac ("edac: change the mem allocation scheme to make Documentation/kobject.txt happy") changed the memory allocation for the csrows member. But ppc4xx_edac was forgotten in the patch. Fix it. Signed-off-by: Michael Walle <michael@walle.cc> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Link: http://lkml.kernel.org/r/1437469253-8611-1-git-send-email-michael@walle.cc Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-13dm thin metadata: delete btrees when releasing metadata snapshotJoe Thornber
commit 7f518ad0a212e2a6fd68630e176af1de395070a7 upstream. The device details and mapping trees were just being decremented before. Now btree_del() is called to do a deep delete. Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16md/bitmap: return an error when bitmap superblock is corrupt.NeilBrown
commit b97e92574c0bf335db1cd2ec491d8ff5cd5d0b49 upstream Use separate bitmaps for each nodes in the cluster bitmap_read_sb() validates the bitmap superblock that it reads in. If it finds an inconsistency like a bad magic number or out-of-range version number, it prints an error and returns, but it incorrectly returns zero, so the array is still assembled with the (invalid) bitmap. This means it could try to use a bitmap with a new version number which it therefore does not understand. This bug was introduced in 3.5 and fix as part of a larger patch in 4.1. So the patch is suitable for any -stable kernel in that range. Fixes: 27581e5ae01f ("md/bitmap: centralise allocation of bitmap file pages.") Signed-off-by: NeilBrown <neilb@suse.com> Reported-by: GuoQing Jiang <gqjiang@suse.com>
2015-08-16sg_start_req(): make sure that there's not too many elements in iovecAl Viro
commit 451a2886b6bf90e2fb378f7c46c655450fb96e81 upstream. unfortunately, allowing an arbitrary 16bit value means a possibility of overflow in the calculation of total number of pages in bio_map_user_iov() - we rely on there being no more than PAGE_SIZE members of sum in the first loop there. If that sum wraps around, we end up allocating too small array of pointers to pages and it's easy to overflow it in the second loop. X-Coverup: TINC (and there's no lumber cartel either) Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> [bwh: s/MAX_UIOVEC/UIO_MAXIOV/. This was fixed upstream by commit fdc81f45e9f5 ("sg_start_req(): use import_iovec()"), but we don't have that function.] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16md/raid1: extend spinlock to protect raid1_end_read_request against ↵NeilBrown
inconsistencies commit 423f04d63cf421ea436bcc5be02543d549ce4b28 upstream. raid1_end_read_request() assumes that the In_sync bits are consistent with the ->degaded count. raid1_spare_active updates the In_sync bit before the ->degraded count and so exposes an inconsistency, as does error() So extend the spinlock in raid1_spare_active() and error() to hide those inconsistencies. This should probably be part of Commit: 34cab6f42003 ("md/raid1: fix test for 'was read error from last working device'.") as it addresses the same issue. It fixes the same bug and should go to -stable for same reasons. Fixes: 76073054c95b ("md/raid1: clean up read_balance.") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16iscsi-target: Fix iscsit_start_kthreads failure OOPsNicholas Bellinger
commit e54198657b65625085834847ab6271087323ffea upstream. This patch fixes a regression introduced with the following commit in v4.0-rc1 code, where a iscsit_start_kthreads() failure triggers a NULL pointer dereference OOPs: commit 88dcd2dab5c23b1c9cfc396246d8f476c872f0ca Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Feb 26 22:19:15 2015 -0800 iscsi-target: Convert iscsi_thread_set usage to kthread.h To address this bug, move iscsit_start_kthreads() immediately preceeding the transmit of last login response, before signaling a successful transition into full-feature-phase within existing iscsi_target_do_tx_login_io() logic. This ensures that no target-side resource allocation failures can occur after the final login response has been successfully sent. Also, it adds a iscsi_conn->rx_login_comp to allow the RX thread to sleep to prevent other socket related failures until the final iscsi_post_login_handler() call is able to complete. Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@daterainc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16rbd: fix copyup completion raceIlya Dryomov
commit 2761713d35e370fd640b5781109f753066b746c4 upstream. For write/discard obj_requests that involved a copyup method call, the opcode of the first op is CEPH_OSD_OP_CALL and the ->callback is rbd_img_obj_copyup_callback(). The latter frees copyup pages, sets ->xferred and delegates to rbd_img_obj_callback(), the "normal" image object callback, for reporting to block layer and putting refs. rbd_osd_req_callback() however treats CEPH_OSD_OP_CALL as a trivial op, which means obj_request is marked done in rbd_osd_trivial_callback(), *before* ->callback is invoked and rbd_img_obj_copyup_callback() has a chance to run. Marking obj_request done essentially means giving rbd_img_obj_callback() a license to end it at any moment, so if another obj_request from the same img_request is being completed concurrently, rbd_img_obj_end_request() may very well be called on such prematurally marked done request: <obj_request-1/2 reply> handle_reply() rbd_osd_req_callback() rbd_osd_trivial_callback() rbd_obj_request_complete() rbd_img_obj_copyup_callback() rbd_img_obj_callback() <obj_request-2/2 reply> handle_reply() rbd_osd_req_callback() rbd_osd_trivial_callback() for_each_obj_request(obj_request->img_request) { rbd_img_obj_end_request(obj_request-1/2) rbd_img_obj_end_request(obj_request-2/2) <-- } Calling rbd_img_obj_end_request() on such a request leads to trouble, in particular because its ->xfferred is 0. We report 0 to the block layer with blk_update_request(), get back 1 for "this request has more data in flight" and then trip on rbd_assert(more ^ (which == img_request->obj_request_count)); with rhs (which == ...) being 1 because rbd_img_obj_end_request() has been called for both requests and lhs (more) being 1 because we haven't got a chance to set ->xfferred in rbd_img_obj_copyup_callback() yet. To fix this, leverage that rbd wants to call class methods in only two cases: one is a generic method call wrapper (obj_request is standalone) and the other is a copyup (obj_request is part of an img_request). So make a dedicated handler for CEPH_OSD_OP_CALL and directly invoke rbd_img_obj_copyup_callback() from it if obj_request is part of an img_request, similar to how CEPH_OSD_OP_READ handler invokes rbd_img_obj_request_read_callback(). Since rbd_img_obj_copyup_callback() is now being called from the OSD request callback (only), it is renamed to rbd_osd_copyup_callback(). Cc: Alex Elder <elder@linaro.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16crypto: ixp4xx - Remove bogus BUG_ON on scattered dst bufferHerbert Xu
commit f898c522f0e9ac9f3177d0762b76e2ab2d2cf9c0 upstream. This patch removes a bogus BUG_ON in the ablkcipher path that triggers when the destination buffer is different from the source buffer and is scattered. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16xen/gntdevt: Fix race condition in gntdev_release()Marek Marczykowski-Górecki
commit 30b03d05e07467b8c6ec683ea96b5bffcbcd3931 upstream. While gntdev_release() is called the MMU notifier is still registered and can traverse priv->maps list even if no pages are mapped (which is the case -- gntdev_release() is called after all). But gntdev_release() will clear that list, so make sure that only one of those things happens at the same time. Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16mfd: sm501: dbg_regs attribute must be read-onlyGuenter Roeck
commit 8a8320c2e78d1b619a8fa8eb5ae946b8691de604 upstream. Fix: sm501 sm501: SM501 At b3e00000: Version 050100a0, 8 Mb, IRQ 100 Attribute dbg_regs: write permission without 'store' ------------[ cut here ]------------ WARNING: at drivers/base/core.c:620 dbg_regs does not have a write function and must therefore be marked as read-only. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16ipmi: fix timeout calculation when bmc is disconnectedXie XiuQi
commit e21404dc0ac7ac971c1e36274b48bb460463f4e5 upstream. Loading ipmi_si module while bmc is disconnected, we found the timeout is longer than 5 secs. Actually it takes about 3 mins and 20 secs.(HZ=250) error message as below: Dec 12 19:08:59 linux kernel: IPMI BT: timeout in RD_WAIT [ ] 1 retries left Dec 12 19:08:59 linux kernel: BT: write 4 bytes seq=0x01 03 18 00 01 [...] Dec 12 19:12:19 linux kernel: IPMI BT: timeout in RD_WAIT [ ] Dec 12 19:12:19 linux kernel: failed 2 retries, sending error response Dec 12 19:12:19 linux kernel: IPMI: BT reset (takes 5 secs) Dec 12 19:12:19 linux kernel: IPMI BT: flag reset [ ] Function wait_for_msg_done() use schedule_timeout_uninterruptible(1) to sleep 1 tick, so we should subtract jiffies_to_usecs(1) instead of 100 usecs from timeout. Reported-by: Hu Shiyuan <hushiyuan@huawei.com> Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16md: use kzalloc() when bitmap is disabledBenjamin Randazzo
commit b6878d9e03043695dbf3fa1caa6dfc09db225b16 upstream. In drivers/md/md.c get_bitmap_file() uses kmalloc() for creating a mdu_bitmap_file_t called "file". 5769 file = kmalloc(sizeof(*file), GFP_NOIO); 5770 if (!file) 5771 return -ENOMEM; This structure is copied to user space at the end of the function. 5786 if (err == 0 && 5787 copy_to_user(arg, file, sizeof(*file))) 5788 err = -EFAULT But if bitmap is disabled only the first byte of "file" is initialized with zero, so it's possible to read some bytes (up to 4095) of kernel space memory from user space. This is an information leak. 5775 /* bitmap disabled, zero the first byte and copy out */ 5776 if (!mddev->bitmap_info.file) 5777 file->pathname[0] = '\0'; Signed-off-by: Benjamin Randazzo <benjamin@randazzo.fr> Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16USB: sierra: add 1199:68AB device IDDirk Behme
commit 74472233233f577eaa0ca6d6e17d9017b6e53150 upstream. Add support for the Sierra Wireless AR8550 device with USB descriptor 0x1199, 0x68AB. It is common with MC879x modules 1199:683c/683d which also are composite devices with 7 interfaces (0..6) and also MDM62xx based as the AR8550. The major difference are only the interface attributes 02/02/01 on interfaces 3 and 4 on the AR8550. They are vendor specific ff/ff/ff on MC879x modules. lsusb reports: Bus 001 Device 004: ID 1199:68ab Sierra Wireless, Inc. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x1199 Sierra Wireless, Inc. idProduct 0x68ab bcdDevice 0.06 iManufacturer 3 Sierra Wireless, Incorporated iProduct 2 AR8550 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 198 bNumInterfaces 7 bConfigurationValue 1 iConfiguration 1 Sierra Configuration bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 3 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x84 EP 4 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 4 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x87 EP 7 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 5 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x88 EP 8 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x89 EP 9 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 6 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x8a EP 10 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x8b EP 11 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x07 EP 7 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Cc: Lars Melin <larsm17@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16xhci: fix off by one error in TRB DMA address boundary checkMathias Nyman
commit 7895086afde2a05fa24a0e410d8e6b75ca7c8fdd upstream. We need to check that a TRB is part of the current segment before calculating its DMA address. Previously a ring segment didn't use a full memory page, and every new ring segment got a new memory page, so the off by one error in checking the upper bound was never seen. Now that we use a full memory page, 256 TRBs (4096 bytes), the off by one didn't catch the case when a TRB was the first element of the next segment. This is triggered if the virtual memory pages for a ring segment are next to each in increasing order where the ring buffer wraps around and causes errors like: [ 106.398223] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 0 comp_code 1 [ 106.398230] xhci_hcd 0000:00:14.0: Looking for event-dma fffd3000 trb-start fffd4fd0 trb-end fffd5000 seg-start fffd4000 seg-end fffd4ff0 The trb-end address is one outside the end-seg address. Tested-by: Arkadiusz Miśkiewicz <arekm@maven.pl> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16ipr: Fix invalid array indexing for HRRQBrian King
commit 3f1c0581310d5d94bd72740231507e763a6252a4 upstream. Fixes another signed / unsigned array indexing bug in the ipr driver. Currently, when hrrq_index wraps, it becomes a negative number. We do the modulo, but still have a negative number, so we end up indexing backwards in the array. Given where the hrrq array is located in memory, we probably won't actually reference memory we don't own, but nonetheless ipr is still looking at data within struct ipr_ioa_cfg and interpreting it as struct ipr_hrr_queue data, so bad things could certainly happen. Each ipr adapter has anywhere from 1 to 16 HRRQs. By default, we use 2 on new adapters. Let's take an example: Assume ioa_cfg->hrrq_index=0x7fffffffe and ioa_cfg->hrrq_num=4: The atomic_add_return will then return -1. We mod this with 3 and get -2, add one and get -1 for an array index. On adapters which support more than a single HRRQ, we dedicate HRRQ to adapter initialization and error interrupts so that we can optimize the other queues for fast path I/O. So all normal I/O uses HRRQ 1-15. So we want to spread the I/O requests across those HRRQs. With the default module parameter settings, this bug won't hit, only when someone sets the ipr.number_of_msix parameter to a value larger than 3 is when bad things start to happen. Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16ipr: Fix incorrect trace indexingBrian King
commit bb7c54339e6a10ecce5c4961adf5e75b3cf0af30 upstream. When ipr's internal driver trace was changed to an atomic, a signed/unsigned bug slipped in which results in us indexing backwards in our memory buffer writing on memory that does not belong to us. This patch fixes this by removing the modulo and instead just mask off the low bits. Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-16ipr: Fix locking for unit attention handlingBrian King
commit 36b8e180e1e929e00b351c3b72aab3147fc14116 upstream. Make sure we have the host lock held when calling scsi_report_bus_reset. Fixes a crash seen as the __devices list in the scsi host was changing as we were iterating through it. Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-09-13 09:28:42 +0000