| Age | Commit message (Collapse) | Author |
|---|
|
The fastmap update code might erase the current fastmap anchor PEB
in case it doesn't find any new free PEB. When a power cut happens
in this situation we must not have any outdated fastmap anchor PEB
on the device, because that would be used to attach during next
boot.
The easiest way to make that sure is to erase all outdated fastmap
anchor PEBs synchronously during attach.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Fixes: dbb7d2a88d2a ("UBI: Add fastmap core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Usually Fastmap is free to consider every PEB in one of the pools
as newer than the existing PEB. Since PEBs in a pool are by definition
newer than everything else.
But update_vol() missed the case that a pool can contain more than
one candidate.
Cc: <stable@vger.kernel.org>
Fixes: dbb7d2a88d ("UBI: Add fastmap core")
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
When writing a new Fastmap the first thing that happens
is refilling the pools in memory.
At this stage it is possible that new PEBs from the new pools
get already claimed and written with data.
If this happens before the new Fastmap data structure hits the
flash and we face power cut the freshly written PEB will not
scanned and unnoticed.
Solve the issue by locking the pools until Fastmap is written.
Cc: <stable@vger.kernel.org>
Fixes: dbb7d2a88d ("UBI: Add fastmap core")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Since PEB erasure is asynchornous it can happen that there is
more than one Fastmap on the MTD. This is fine because the attach logic
will pick the Fastmap data structure with the highest sequence number.
On a not so well configured MTD stack spurious ECC errors are common.
Causes can be different, bad hardware, wrong operating modes, etc...
If the most current Fastmap renders bad due to ECC errors UBI might
pick an older Fastmap to attach from.
While this can only happen on an anyway broken setup it will show
completely different sympthoms and makes finding the root cause much
more difficult.
So, be debug friendly and fall back to scanning mode of we're facing
an ECC error while scanning for Fastmap.
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Introduce a new list to the UBI attach information
object to be able to deal better with old and corrupted
Fastmap eraseblocks.
Also move more Fastmap specific code into fastmap.c.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
This makes the logic more easy to follow.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
(cherry picked from commit 22a2065b9a3fa6ad458e3100b66c4acaa05f2466)
|
|
After overruns the FIFO pointers become misaligned. This
typically shows by characters still being stuck in the FIFO
despite the empty flag being asserted. After the first
assertion of the overrun flag the empty flag still seems to
indicate FIFO state correctly and all data can be read.
However, after another overrun assertion the FIFO seems to
be off by one such that the last received character is still
in the FIFO (despite the empty flag being asserted).
Flushing the receive FIFO reinitializes pointers. Hence it
is recommended to flush the FIFO after overruns, see also:
https://community.nxp.com/thread/321175
Hence, on assertion of the overrun flag read the remaining
data from the FIFO and flush buffers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
When using DMA framing error get cleared properly. However, due
to the additional read from the data register, an underflow in
the receive FIFO buffer occures (the FIFO pointer gets out of
sync).
Clear the FIFO in case an underflow has occured. Also disable
the receiver during this operation and when reading the data
register to minimize potential interference.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
This is the 4.4.138 stable release
|
|
commit 1411b5218adbcf1d45ddb260db5553c52e8d917c upstream.
In the vmx AES init routines we do a printk(KERN_INFO ...) to report
the fallback implementation we're using.
However with a slow console this can significantly affect the speed of
crypto operations. Using 'cryptsetup benchmark' the removal of the
printk() leads to a ~5x speedup for aes-cbc decryption.
So remove them.
Fixes: 8676590a1593 ("crypto: vmx - Adding AES routines for VMX module")
Fixes: 8c755ace357c ("crypto: vmx - Adding CBC routines for VMX module")
Fixes: 4f7f60d312b3 ("crypto: vmx - Adding CTR routines for VMX module")
Fixes: cc333cd68dfa ("crypto: vmx - Adding GHASH routines for VMX module")
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6e7e9cd8eed0e18217c899843bffbe8c7dae564 upstream.
Add ELAN0612 to the list of supported touchpads; this ID is used in Lenovo
v330 14IKB devices.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199253
Signed-off-by: Johannes Wienke <languitar@semipol.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ca4d1ae9bad0f59bd6f851c39b19f5366953666 upstream.
GPD Win 2 Website: http://www.gpd.hk/gpdwin2.asp
Tested on a unit from the first production run sent to Indiegogo backers
Signed-off-by: Ethan Lee <flibitijibibo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b23220fe054e92f616b82450fae8cd3ab176cc60 upstream.
The balloon.page field is used for two different purposes if batching is
on or off. If batching is on, the field point to the page which is used
to communicate with with the hypervisor. If it is off, balloon.page
points to the page that is about to be (un)locked.
Unfortunately, this dual-purpose of the field introduced a bug: when the
balloon is popped (e.g., when the machine is reset or the balloon driver
is explicitly removed), the balloon driver frees, unconditionally, the
page that is held in balloon.page. As a result, if batching is
disabled, this leads to double freeing the last page that is sent to the
hypervisor.
The following error occurs during rmmod when kernel checkers are on, and
the balloon is not empty:
[ 42.307653] ------------[ cut here ]------------
[ 42.307657] Kernel BUG at ffffffffba1e4b28 [verbose debug info unavailable]
[ 42.307720] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
[ 42.312512] Modules linked in: vmw_vsock_vmci_transport vsock ppdev joydev vmw_balloon(-) input_leds serio_raw vmw_vmci parport_pc shpchp parport i2c_piix4 nfit mac_hid autofs4 vmwgfx drm_kms_helper hid_generic syscopyarea sysfillrect usbhid sysimgblt fb_sys_fops hid ttm mptspi scsi_transport_spi ahci mptscsih drm psmouse vmxnet3 libahci mptbase pata_acpi
[ 42.312766] CPU: 10 PID: 1527 Comm: rmmod Not tainted 4.12.0+ #5
[ 42.312803] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 09/30/2016
[ 42.313042] task: ffff9bf9680f8000 task.stack: ffffbfefc1638000
[ 42.313290] RIP: 0010:__free_pages+0x38/0x40
[ 42.313510] RSP: 0018:ffffbfefc163be98 EFLAGS: 00010246
[ 42.313731] RAX: 000000000000003e RBX: ffffffffc02b9720 RCX: 0000000000000006
[ 42.313972] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9bf97e08e0a0
[ 42.314201] RBP: ffffbfefc163be98 R08: 0000000000000000 R09: 0000000000000000
[ 42.314435] R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffc02b97e4
[ 42.314505] R13: ffffffffc02b9748 R14: ffffffffc02b9728 R15: 0000000000000200
[ 42.314550] FS: 00007f3af5fec700(0000) GS:ffff9bf97e080000(0000) knlGS:0000000000000000
[ 42.314599] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 42.314635] CR2: 00007f44f6f4ab24 CR3: 00000003a7d12000 CR4: 00000000000006e0
[ 42.314864] Call Trace:
[ 42.315774] vmballoon_pop+0x102/0x130 [vmw_balloon]
[ 42.315816] vmballoon_exit+0x42/0xd64 [vmw_balloon]
[ 42.315853] SyS_delete_module+0x1e2/0x250
[ 42.315891] entry_SYSCALL_64_fastpath+0x23/0xc2
[ 42.315924] RIP: 0033:0x7f3af5b0e8e7
[ 42.315949] RSP: 002b:00007fffe6ce0148 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ 42.315996] RAX: ffffffffffffffda RBX: 000055be676401e0 RCX: 00007f3af5b0e8e7
[ 42.316951] RDX: 000000000000000a RSI: 0000000000000800 RDI: 000055be67640248
[ 42.317887] RBP: 0000000000000003 R08: 0000000000000000 R09: 1999999999999999
[ 42.318845] R10: 0000000000000883 R11: 0000000000000206 R12: 00007fffe6cdf130
[ 42.319755] R13: 0000000000000000 R14: 0000000000000000 R15: 000055be676401e0
[ 42.320606] Code: c0 74 1c f0 ff 4f 1c 74 02 5d c3 85 f6 74 07 e8 0f d8 ff ff 5d c3 31 f6 e8 c6 fb ff ff 5d c3 48 c7 c6 c8 0f c5 ba e8 58 be 02 00 <0f> 0b 66 0f 1f 44 00 00 66 66 66 66 90 48 85 ff 75 01 c3 55 48
[ 42.323462] RIP: __free_pages+0x38/0x40 RSP: ffffbfefc163be98
[ 42.325735] ---[ end trace 872e008e33f81508 ]---
To solve the bug, we eliminate the dual purpose of balloon.page.
Fixes: f220a80f0c2e ("VMware balloon: add batching to the vmw_balloon.")
Cc: stable@vger.kernel.org
Reported-by: Oleksandr Natalenko <onatalen@redhat.com>
Signed-off-by: Gil Kupfer <gilkup@gmail.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Xavier Deguillard <xdeguillard@vmware.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa2f80e752c75e593b3820f42c416ed9458fa73e upstream.
The best granularity of residue that DMA engine can report is in the BURST
units, so the serial driver must use MAXBURST = 1 and DMA_SLAVE_BUSWIDTH_1_BYTE
if it relies on exact number of bytes transferred by DMA engine.
Fixes: 62c37eedb74c ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d18f0a14aa6a0d6bad39111c1fb655f07f71d59 upstream.
Sometimes a GPIO is fetched with NULL as parent device, and
that is just fine. So under these circumstances, avoid using
dev_name() to provide a name for the GPIO line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Rosenberg <drosen@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 362f924b64ba0f4be2ee0cb697690c33d40be721 upstream.
Those are stupid and code should use static_cpu_has_safe() or
boot_cpu_has() instead. Kill the least used and unused ones.
The remaining ones need more careful inspection before a conversion can
happen. On the TODO.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1449481182-27541-4-git-send-email-bp@alien8.de
Cc: David Sterba <dsterba@suse.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 79fb218d97980d4fee9a64f4c8ff05289364ba25 ]
On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.
Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.
broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).
Fixes: a1cba5613edf ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 25ea66544bfd1d9df1b7e1502f8717e85fa1e6e6 ]
This code was introduced in 2011 around the same time that we made
netdev_features_t a u64 type. These days a u32 is not big enough to
hold all the potential features.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d546b67cda015fb92bfee93d5dc0ceadb91deaee ]
spin_lock/unlock was used instead of spin_un/lock_irq
in a procedure used in process space, on a spinlock
which can be grabbed in an interrupt.
This caused the stack trace below to be displayed (on kernel
4.17.0-rc1 compiled with Lock Debugging enabled):
[ 154.661474] WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
[ 154.668909] 4.17.0-rc1-rdma_rc_mlx+ #3 Tainted: G I
[ 154.675856] -----------------------------------------------------
[ 154.682706] modprobe/10159 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[ 154.690254] 00000000f3b0e495 (&(&qp_table->lock)->rlock){+.+.}, at: mlx4_qp_remove+0x20/0x50 [mlx4_core]
[ 154.700927]
and this task is already holding:
[ 154.707461] 0000000094373b5d (&(&cq->lock)->rlock/1){....}, at: destroy_qp_common+0x111/0x560 [mlx4_ib]
[ 154.718028] which would create a new lock dependency:
[ 154.723705] (&(&cq->lock)->rlock/1){....} -> (&(&qp_table->lock)->rlock){+.+.}
[ 154.731922]
but this new dependency connects a SOFTIRQ-irq-safe lock:
[ 154.740798] (&(&cq->lock)->rlock){..-.}
[ 154.740800]
... which became SOFTIRQ-irq-safe at:
[ 154.752163] _raw_spin_lock_irqsave+0x3e/0x50
[ 154.757163] mlx4_ib_poll_cq+0x36/0x900 [mlx4_ib]
[ 154.762554] ipoib_tx_poll+0x4a/0xf0 [ib_ipoib]
...
to a SOFTIRQ-irq-unsafe lock:
[ 154.815603] (&(&qp_table->lock)->rlock){+.+.}
[ 154.815604]
... which became SOFTIRQ-irq-unsafe at:
[ 154.827718] ...
[ 154.827720] _raw_spin_lock+0x35/0x50
[ 154.833912] mlx4_qp_lookup+0x1e/0x50 [mlx4_core]
[ 154.839302] mlx4_flow_attach+0x3f/0x3d0 [mlx4_core]
Since mlx4_qp_lookup() is called only in process space, we can
simply replace the spin_un/lock calls with spin_un/lock_irq calls.
Fixes: 6dc06c08bef1 ("net/mlx4: Fix the check in attaching steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fdd13dd350dda1826579eb5c333d76b14513b812 ]
ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.
Fix that mask to handle 64bit physical address.
Fixes: fe56b9e6a8d9 ("qed: Add module with basic common support")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9f7c728332e8966084242fcd951aa46583bc308c ]
Testing Telit LM940 with ICMP packets > 14552 bytes revealed that
the modem needs FLAG_SEND_ZLP to properly work, otherwise the cdc
mbim data interface won't be anymore responsive.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6009d1fe6ba3bb2dab55921da60465329cc1cd89 ]
In divasmain.c, the function divas_write() firstly invokes the function
diva_xdi_open_adapter() to open the adapter that matches with the adapter
number provided by the user, and then invokes the function diva_xdi_write()
to perform the write operation using the matched adapter. The two functions
diva_xdi_open_adapter() and diva_xdi_write() are located in diva.c.
In diva_xdi_open_adapter(), the user command is copied to the object 'msg'
from the userspace pointer 'src' through the function pointer 'cp_fn',
which eventually calls copy_from_user() to do the copy. Then, the adapter
number 'msg.adapter' is used to find out a matched adapter from the
'adapter_queue'. A matched adapter will be returned if it is found.
Otherwise, NULL is returned to indicate the failure of the verification on
the adapter number.
As mentioned above, if a matched adapter is returned, the function
diva_xdi_write() is invoked to perform the write operation. In this
function, the user command is copied once again from the userspace pointer
'src', which is the same as the 'src' pointer in diva_xdi_open_adapter() as
both of them are from the 'buf' pointer in divas_write(). Similarly, the
copy is achieved through the function pointer 'cp_fn', which finally calls
copy_from_user(). After the successful copy, the corresponding command
processing handler of the matched adapter is invoked to perform the write
operation.
It is obvious that there are two copies here from userspace, one is in
diva_xdi_open_adapter(), and one is in diva_xdi_write(). Plus, both of
these two copies share the same source userspace pointer, i.e., the 'buf'
pointer in divas_write(). Given that a malicious userspace process can race
to change the content pointed by the 'buf' pointer, this can pose potential
security issues. For example, in the first copy, the user provides a valid
adapter number to pass the verification process and a valid adapter can be
found. Then the user can modify the adapter number to an invalid number.
This way, the user can bypass the verification process of the adapter
number and inject inconsistent data.
This patch reuses the data copied in
diva_xdi_open_adapter() and passes it to diva_xdi_write(). This way, the
above issues can be avoided.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 322eaa06d55ebc1402a4a8d140945cff536638b4 ]
In commit 624dbf55a359b ("driver/net: enic: Try DMA 64 first, then
failover to DMA") DMA mask was changed from 40 bits to 64 bits.
Hardware actually supports only 47 bits.
Fixes: 624dbf55a359b ("driver/net: enic: Try DMA 64 first, then failover to DMA")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dd612f18a49b63af8b3a5f572d999bdb197385bc ]
Nearby code that also tests port suggests that the P0 constant should be
used when port is zero.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
@@
* e ? e1 : e1
// </smpl>
Fixes: 6c3218c6f7e5 ("bnx2x: Adjust ETS to 578xx")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9b9322db5c5a1917a66c71fe47c3848a9a31227e upstream.
The commit "regulatory: add NUL to request alpha2" increases the length of
alpha2 to 3. This causes a regression on brcmfmac, because
brcmf_cfg80211_reg_notifier() expect valid ISO3166 codes in the complete
array. So fix this accordingly.
Fixes: 657308f73e67 ("regulatory: add NUL to request alpha2")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 4.4: adjust filename]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76ef6b28ea4f81c3d511866a9b31392caa833126 upstream.
Since we have the ttm and gem vma managers using a subset
of the file address space for objects, and these start at
0x100000000 they will overflow the new mmap checks.
I've checked all the mmap routines I could see for any
bad behaviour but overall most people use GEM/TTM VMA
managers even the legacy drivers have a hashtable.
Reported-and-Tested-by: Arthur Marsh (amarsh04 on #radeon)
Fixes: be83bbf8068 (mmap: introduce sane default mmap limits)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0803d7befa15cab5717d667a97a66214d2a4c083 upstream.
The Acer Acer Veriton X4110G has a TPM device detected as:
tpm_tis 00:0b: 1.2 TPM (device-id 0xFE, rev-id 71)
After the first S3 suspend, the following error appears during resume:
tpm tpm0: A TPM error(38) occurred continue selftest
Any following S3 suspend attempts will now fail with this error:
tpm tpm0: Error (38) sending savestate before suspend
PM: Device 00:0b failed to suspend: error 38
Error 38 is TPM_ERR_INVALID_POSTINIT which means the TPM is
not in the correct state. This indicates that the platform BIOS
is not sending the usual TPM_Startup command during S3 resume.
>From this point onwards, all TPM commands will fail.
The same issue was previously reported on Foxconn 6150BK8MC and
Sony Vaio TX3.
The platform behaviour seems broken here, but we should not break
suspend/resume because of this.
When the unexpected TPM state is encountered, set a flag to skip the
affected TPM_SaveState command on later suspends.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Link: http://lkml.kernel.org/r/CAB4CAwfSCvj1cudi+MWaB5g2Z67d9DwY1o475YOZD64ma23UiQ@mail.gmail.com
Link: https://lkml.org/lkml/2011/3/28/192
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=591031
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5d0ebc99bf5d0801a5ecbe958caa3d68b8eaee8 upstream.
The suspend/resume behavior of the TPM can be controlled by setting
"powered-while-suspended" in the DTS. This is useful for the cases
when hardware does not power-off the TPM.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3fb22733ae61050f8d10a1d6a8af176c5c5db1a upstream.
Radiant P845 does not have LVDS, only VGA.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105468
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222204.4771-1-linux@rainbow-software.org
(cherry picked from commit 7f7105f99b75aca4f8c2a748ed6b82c7f8be3293)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 806e30873f0e74d9d41b0ef761bd4d3e55c7d510 upstream.
Commit b5e2ced9bf81 ("stm class: Use vmalloc for the master map") caused
a build error on some arches as vmalloc.h was not explicitly included.
Fix that by adding it to the list of includes.
Fixes: b5e2ced9bf81 ("stm class: Use vmalloc for the master map")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5e2ced9bf81393034072dd4d372f6b430bc1f0a upstream.
Fengguang is running into a warning from the buddy allocator:
> swapper/0: page allocation failure: order:9, mode:0x14040c0(GFP_KERNEL|__GFP_COMP), nodemask=(null)
> CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.17.0-rc1 #262
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
> Call Trace:
...
> __kmalloc+0x14b/0x180: ____cache_alloc at mm/slab.c:3127
> stm_register_device+0xf3/0x5c0: stm_register_device at drivers/hwtracing/stm/core.c:695
...
Which is basically a result of the stm class trying to allocate ~512kB
for the dummy_stm with its default parameters. There's no reason, however,
for it not to be vmalloc()ed instead, which is what this patch does.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
CC: stable@vger.kernel.org # v4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c9ddf73476ff4fffb7a87bd5107a0705bf2cf64b upstream.
Since an SRP remote port is attached as a child to shost->shost_gendev
and as the only child, the translation from the shost pointer into an
rport pointer must happen by looking up the shost child that is an
rport. This patch fixes the following KASAN complaint:
BUG: KASAN: slab-out-of-bounds in srp_timed_out+0x57/0x110 [scsi_transport_srp]
Read of size 4 at addr ffff880035d3fcc0 by task kworker/1:0H/19
CPU: 1 PID: 19 Comm: kworker/1:0H Not tainted 4.16.0-rc3-dbg+ #1
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
dump_stack+0x85/0xc7
print_address_description+0x65/0x270
kasan_report+0x231/0x350
srp_timed_out+0x57/0x110 [scsi_transport_srp]
scsi_times_out+0xc7/0x3f0 [scsi_mod]
blk_mq_terminate_expired+0xc2/0x140
bt_iter+0xbc/0xd0
blk_mq_queue_tag_busy_iter+0x1c7/0x350
blk_mq_timeout_work+0x325/0x3f0
process_one_work+0x441/0xa50
worker_thread+0x76/0x6c0
kthread+0x1b2/0x1d0
ret_from_fork+0x24/0x30
Fixes: e68ca75200fe ("scsi_transport_srp: Reduce failover time")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d13de4b027d5f6276c0f9d3a264f518747d83f2 upstream.
Currently, the following causes a kernel OOPS in memcpy:
echo 1073741825 > buffer/length
echo 1 > buffer/enable
Note that using 1073741824 instead of 1073741825 causes "write error:
Cannot allocate memory" but no OOPS.
This is because 1073741824 == 2^30 and 1073741825 == 2^30+1. Since kfifo
rounds up to the nearest power of 2, it will actually call kmalloc with
roundup_pow_of_two(length) * bytes_per_datum.
Using length == 1073741825 and bytes_per_datum == 2, we get:
kmalloc(roundup_pow_of_two(1073741825) * 2
or kmalloc(2147483648 * 2)
or kmalloc(4294967296)
or kmalloc(UINT_MAX + 1)
so this overflows to 0, causing kmalloc to return ZERO_SIZE_PTR and
subsequent memcpy to fail once the device is enabled.
Fix this by checking for overflow prior to allocating a kfifo. With this
check added, the above code returns -EINVAL when enabling the buffer,
rather than causing an OOPS.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9f5efade2cfd729138a7cafb46d01044da40f5e upstream.
This patch fixes an issue that list_for_each_entry() in
usb_dmac_chan_terminate_all() is possible to cause endless loop because
this will move own desc to the desc_freed. So, this driver should use
list_for_each_entry_safe() instead of list_for_each_entry().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52df445f29b79006d8b2dcd129152987c0d3bd64 upstream.
If we don't clear START generation as soon as possible, it may cause
another message to be generated, e.g. when receiving NACK in address
phase. To keep the race window as small as possible, we clear it right
at the beginning of the interrupt. We don't need any checks since we
always want to stop START and STOP generation on the next occasion after
we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3be0af15959e11fa535d5332ab3d7cf34abd09b upstream.
Due to the HW design, master IRQs are timing critical, so give them
precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d89667b14f9d13b684287f6189ca209af5feee43 upstream.
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cc21d0b4b62e41e5013d763adade5ea4462c33a4 upstream.
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9d0684c79c4b9d30ce0d47d3270493dd0e76e59 upstream.
We want to reuse this function later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff2316b87a336bff940939cd9fc56287ed48e578 upstream.
After making sure to reinit the HW and clear interrupts in the timeout
case, we know that interrupts are always disabled in the sections
protected by the spinlock. Thus, we can simply remove it which is a
preparation for further refactoring. While here, rename the timeout
variable to time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90f779e565bdc18dd4f79d81cf11f43a7266010b upstream.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c78cdc1c06308a59d6ed4145cdba73fdeff8c0d upstream.
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e43e0df13f8528ca55ed79f469c4b2af897fa796 upstream.
When calculating the bus speed, the clock should be on, of course. Most
bootloaders left them on, so this went unnoticed so far.
Move the ioremapping out of this clock-enabled-block and prepare for
adding hw initialization there, too.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c9bd28233b6d0d82ac3ba0215723be0a8262c39c upstream.
irda_get_mtt() returns a hardcoded '10000' in some cases,
and with gcc-7, we get a build error because this triggers a
compile-time check in udelay():
drivers/net/irda/w83977af_ir.o: In function `w83977af_hard_xmit':
w83977af_ir.c:(.text.w83977af_hard_xmit+0x14c): undefined reference to `__bad_udelay'
Older compilers did not run into this because they either did not
completely inline the irda_get_mtt() or did not consider the
10000 value a constant expression.
The code has been wrong since the start of git history.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fb239c1209bb0f0b4830cc72507cc2f2d63fadbd upstream.
In _rtl92c_get_txpower_writeval_by_regulatory() the variable writeVal
is assigned to itself in an if ... else statement, apparently only to
document that the branch condition is handled and that a previously read
value should be returned unmodified. The self-assignment causes clang to
raise the following warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:304:13:
error: explicitly assigning value of variable of type 'u32'
(aka 'unsigned int') to itself [-Werror,-Wself-assign]
writeVal = writeVal;
Delete the branch with the self-assignment.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40f7090bb1b4ec327ea1e1402ff5783af5b35195 upstream.
New ICs (like the one on the Lenovo T480s) answer to
ETP_SMBUS_IAP_VERSION_CMD 4 bytes instead of 3. This corrupts the stack
as i2c_smbus_read_block_data() uses the values returned by the i2c
device to know how many data it need to return.
i2c_smbus_read_block_data() can read up to 32 bytes (I2C_SMBUS_BLOCK_MAX)
and there is no safeguard on how many bytes are provided in the return
value. Ensure we always have enough space for any future firmware.
Also 0-initialize the values to prevent any access to uninitialized memory.
Cc: <stable@vger.kernel.org> # v4.4.x, v4.9.x, v4.14.x, v4.15.x, v4.16.x
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 009615ab7fd4e43b82a38e4e6adc5e23c1ee567f upstream.
On sparc32, tcflag_t is unsigned long, unlike all other architectures:
drivers/usb/serial/cp210x.c: In function 'cp210x_get_termios':
drivers/usb/serial/cp210x.c:717:3: warning: passing argument 2 of 'cp210x_get_termios_port' from incompatible pointer type
cp210x_get_termios_port(tty->driver_data,
^
drivers/usb/serial/cp210x.c:35:13: note: expected 'unsigned int *' but argument is of type 'tcflag_t *'
static void cp210x_get_termios_port(struct usb_serial_port *port,
^
Consistently use tcflag_t to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fed03fe7e55b7dc16077f672bd9d7bbe92b3a691 ]
The Asus Z370-I contains a Realtek RTL8822BE device with an associated
BT chip using a USB ID of 0b05:185c. This device is added to the driver.
Signed-off-by: Hon Weng Chong <honwchong@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'of_regulator_match()'
[ Upstream commit 30966861a7a2051457be8c49466887d78cc47e97 ]
If an unlikely failure in 'of_get_regulator_init_data()' occurs, we must
release the reference on the current 'child' node before returning.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
