summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2011-08-07netxen: add vlan LRO supportRajesh Borundia
o To support vlan lro, driver need to program ip address in device. o Same ip addresses need to be program after fw recovery, so sotre them in list. o In case of vlan packet, include vlan header length while calculating ip and tcp headers. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-07net/usb: Add IPv6 support to the LG-VL600 LTE USB modem driverMark Kamichoff
The LG-VL600 LTE USB modem supports IPv6, but uses and expects an IPv4 ethertype (0x800) for these packets instead of the standard 0x86dd. This patch peeks at the IP version in the L3 header and sets the ethertype appropriately for IPv6 packets. Signed-off-by: Mark Kamichoff <prox@prolixium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-07qla3xxx: remove an extra semi-colonDan Carpenter
The define is only used one place, and it's at the end of a line so the semi-colon doesn't affect anything. But let's clean it up anyway. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-07ucc_geth: Add SUPPORTED_MII and SUPPORTED_AutonegJoakim Tjernlund
The driver supports Autoneg and at least MII. Tell the PHY that to avoid any confusion in the PHY code. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-07via-velocity : cleanups.françois romieu
- empty lines - tabs / spaces - ETHTOOL_GWOL _is_ defined - useless cast from void * Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-07via-velocity : ethtool statistics support.françois romieu
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Tested-by: Jon Nelson <jnelson@jamponi.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-07via-velocity : update receive packets statistics.françois romieu
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=14076. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Tested-by: Jon Nelson <jnelson@jamponi.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03slip: cleanup statistics generationMatvejchikov Ilya
Remove unused tx_compressed, tx_compressed and tx_misses fields from the slip structure. Also, make some device stats generation cleanups. Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03be2net: fix cmd-rx-filter not notifying MCCSathya Perla
Dave, I missed out on this line while composing the 4/6 patch from my yesterday's patchset ("[PATCH net-next 4/6] be2net: use RX_FILTER cmd to program multicast addresses"). As you've already queued up the patchset for net-next, I'm sending the fix in a separate patch. Pls apply. Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03bna: Remove Obsolete File bfi_ctreg.hRasesh Mody
Change detail: - Remove obsolete file bfi_ctreg.h as we added new file bfi_reg.h consolidating HW reg definitions including the ones for new HW. Signed-off-by: Rasesh Mody <rmody@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03bna: Consolidated HW Registers for Supported HWsRasesh Mody
Change details: - Introducing new file bfi_reg.h for consolidating all supported hardware registers. This file completely replaces bfi_ctreg.h. - Updated ioc code as per register definition change. Signed-off-by: Rasesh Mody <rmody@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03bna: Remove get_regs Ethtool SupportRasesh Mody
Change details: - This patch contains removal of get_regs support in bnad_ethtool.c. Thus BNA will have minimal register definitions necessary for MBOX and interrupt operations Signed-off-by: Rasesh Mody <rmody@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03be2net: drop pkts that do not belong to the portSathya Perla
On some BE skews, while in promiscuous mode, pkts that do not belong to a port can arrive on that port. Drop such pkts. Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03be2net: add support for flashing Teranetics PHY firmwareSathya Perla
Support for flashing RJ45 PHY (from Teranetics) on a 10GBaseT BE3 card. Signed-off-by: Naresh G <bgottumukkala@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03be2net: use RX_FILTER cmd to program multicast addressesSathya Perla
Use this cmd for both promiscous and multicast address programming. Get rid of the old MULTICAST_SET cmd. Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03be2net: non-member vlan pkts not received in promiscous modeSathya Perla
While configuring promiscous mode, explicitly set the VLAN_PROMISCOUS bit to make this happen. When switching off promiscous mode, re-program the vids. Signed-off-by: Xavier Selvin <xavier.selvin@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03be2net: no need to query link statusSathya Perla
Change in the link status generates an MCC event. This is processed and netif_carrier_on/off is called accordingly. Don't need to query/store the link_status state. Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03be2net: remove wrong and unnecessary calls to netif_carrier_off()Sathya Perla
1) In be_probe(), as soon as the MCC Q is created a gratuitous link status event is received and processed. Accordingly netif_carrier_off/on() is called. The extra netif_carrier_off() call in probe can race with this and cause wrong state. 2) be_close() need not call netif_carrier_off(). It is OK to show the actual link state even when the device is administratively down. Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01net/smsc911x: add device tree probe supportShawn Guo
It adds device tree probe support for smsc911x driver. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: David S. Miller <davem@davemloft.net> Reviewed-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01ipg: Use constJoe Perches
Make a couple of declarations const to save some data space. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01ipg: Use current logging stylesJoe Perches
Add and use pr_fmt, pr_<level> and netdev_<level>. Convert printks with %[n].[n]x to %nx to be shorter and clearer. Consolidate printks to use a single printk rather than continued printks without KERN_CONT. Removed unnecessary trailing periods. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01qlcnic: Added debug infoSritej Velaga
Now printing states of essential registers once fw hang has been detected. Bumped up the driver version to 5.0.22 Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01qlcnic: Move get template from probe to start fwSritej Velaga
Place for gathering FW dump template has been moved to the FW restart path so that the driver can check if a newer FW version is available and in that case it replaces the existing FW dump template with the newer template. Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01qlcnic: Fix delay in reset pathSritej Velaga
Driver should not check for heart beat anymore when FW is hung, rather it should restart the FW. Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01qlcnic: FW dump related changesAnirban Chakraborty
o Added code to support FW reset without invoking the dump o Fixed the return value of the dump data size if dump is not available. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01qlcnic: Fix enviroment variable for udev event generation during FW dumpAnirban Chakraborty
Driver was not generating the environment variable for the FW dump event correctly. Fix it by formatting it properly. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01bna: HW Interface Init UpdateRasesh Mody
Change details: - Split the hw interface into common and asic specific to support new asic in the future. - Fix bfa_ioc_ct_isr_mode_set() to also include the case that we are already in the desired msix mode. Signed-off-by: Rasesh Mody <rmody@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01bna: Remove Unnecessary CNA CheckRasesh Mody
Change details: - ioc->cna is always set to 1 for eth functions, remove the check that asserts IOC is in CNA mode in bfa_ioc_firmware_lock() and bfa_ioc_firmware_unlock() in bfa_ioc_ct.c. Signed-off-by: Rasesh Mody <rmody@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01be2net: use stats-sync to read/write 64-bit statsSathya Perla
64-bit stats in be2net are written/read as follows using the stats-sync interface for safe access in 32-bit archs: 64-bit sync writer reader stats ------------------------------------------------------------------------------ tx_stats tx_stats->sync be_xmit be_get_stats64, ethtool tx-compl tx_stats->sync_compl tx-compl-processing ethtool rx-stats rx_stats->sync rx-compl-processing be_get_stats64, ethtool, eqd-update This patch is based on Stephen Hemminger's earlier patch on the same issue... Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01be2net: cleanup and refactor stats codeSathya Perla
In preparation for 64-bit stats interface, the following cleanups help streamline the code: 1) made some more rx/tx stats stored by driver 64 bit 2) made some HW stas (err/drop counters) stored in be_drv_stats 32 bit to keep the code simple as BE provides 32-bit counters only. 3) removed duplication of netdev stats in ethtool 4) removed some un-necessary stats and fixed some names Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2011-07-31mfd: Fix mismatch in twl4030 mutex lock-unlockSanjeev Premi
A mutex is locked on entry into twl4030_madc_conversion(). Immediate return on some error conditions leaves the mutex locked. This patch ensures that mutex is always unlocked before leaving the function. Signed-off-by: Sanjeev Premi <premi@ti.com> Cc: Keerthy <j-keerthy@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: twl6030-pwm.c needs MODULE_LICENSERandy Dunlap
twl6030_pwm: module license 'unspecified' taints kernel. Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Acked-by: Hemanth V <hemanthv@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Fix the omap-usb-host clock API usage on usbhs_disable()Keshava Munegowda
usbhs_disable function was invoking clk_enable() instead of clk_disable(), thus only increasing the clock usage counter and preventing this particular clock from being ever turned off. Because of this, the power domain of omap4 the USB Host subsystem would never reach lower power states.This patch calls clk_disable() in usbhs_disable function Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Acknowledge WM8994 IRQs before reportingMark Brown
This ensures we never have a window where we've handled an interrupt but not told the hardware about it. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Acknowlege all WM831x IRQs before we handle themMark Brown
Ensure that we never have a window where we've handled an interrupt (and therefore need to be notified of new events) but haven't yet told the interrupt controller that this is the case (so any new events will be discarded). Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Avoid two assignments if failures happen in tps65910_i2c_probeJesper Juhl
In drivers/mfd/tps65910.c:tps65910_i2c_probe() there's potential for a tiny optimization. We assign to init_data->irq and init_data->irq_base long before we need them, and there are two potential exits from the function before they are needed. Moving the assignments below these two potential exits means we completely avoid doing them in these two (failure) cases. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: Graeme Gregory <gg@slimlogic.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31regulator: Storing tps65912 error codes in u8Dan Carpenter
get_ctrl_reg() returns -EINVAL so the error handling won't work here if reg is a u8. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Don't leak init_data in tps65910_i2c_probeJesper Juhl
There are a couple of situations where we leak init_data in drivers/mfd/tps65910.c:tps65910_i2c_probe() - this patch should take care of them. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31regulator: aat2870: Add AAT2870 regulator driverJin Park
Add regulator driver for AnalogicTech AAT2870. Signed-off-by: Jin Park <jinyoungp@nvidia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31backlight: Add AAT2870 backlight driverJin Park
Add backlight driver for AnalogicTech AAT2870. Signed-off-by: Jin Park <jinyoungp@nvidia.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Add AAT2870 mfd driverJin Park
Add mfd core driver for AnalogicTech AAT2870. The AAT2870 is communication through I2C and contains backlight and regulator components. Signed-off-by: Jin Park <jinyoungp@nvidia.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Remove dead code from max8997-irqJesper Juhl
We either hit one of the case's or the default in the switch statement in get_i2c(), so the 'return ERR_PTR(-EINVAL);' at the end of the function is just dead code - remove it. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Move TPS55910 Kconfig optionLinus Walleij
Having another TPS chip at the end of the Kconfig when all it's relatives are grouped together in their own section seems totally counter-intuitive. Move it, also in the Makefile. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Fix missing stmpe kerneldocOm Prakash
Generating kerneldoc for STMPE result in warnings, so fix this by adding missing documentation. Signed-off-by: Om Prakash <omprakash.pal@stericsson.com> Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Fix off-by-one value range checking for tps65912_i2c_writeAxel Lin
If bytes == (TPS6591X_MAX_REGISTER + 1), we have a buffer overflow when doing memcpy(&msg[1], src, bytes). Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Add devices for WM831x clocking moduleMark Brown
With the new generic clk API that should appear at some point we should be able to support the clocking sensibly in Linux. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Remove comp{1,2}_threshold sysfs entries in tps65911_comparator_removeAxel Lin
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Don't ask about the TPS65912 core driver in KconfigMark Brown
The user has to select the I2C and SPI drivers individually and they select the core driver for the device so there's no point in presenting the user with an option for the core driver. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Fix off by one in WM831x IRQ codeDimitris Papastamos
The GPIO IRQs aren't the first IRQs defined, we need to subtract the base for the GPIOs as well to use them for array indexes. Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-10-19 15:30:26 +0000