summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2014-12-16igb: bring link up when PHY is powered upTodd Fujinaka
commit aec653c43b0c55667355e26d7de1236bda9fb4e3 upstream. Call igb_setup_link() when the PHY is powered up. Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com> Reported-by: Jeff Westfahl <jeff.westfahl@ni.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Vincent Donnefort <vdonnefort@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16net: mvneta: fix race condition in mvneta_tx()Eric Dumazet
[ Upstream commit 5f478b41033606d325e420df693162e2524c2b94 ] mvneta_tx() dereferences skb to get skb->len too late, as hardware might have completed the transmit and TX completion could have freed the skb from another cpu. Fixes: 71f6d1b31fb1 ("net: mvneta: replace Tx timer with a real interrupt") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16net: mvneta: fix Tx interrupt delaywilly tarreau
[ Upstream commit aebea2ba0f7495e1a1c9ea5e753d146cb2f6b845 ] The mvneta driver sets the amount of Tx coalesce packets to 16 by default. Normally that does not cause any trouble since the driver uses a much larger Tx ring size (532 packets). But some sockets might run with very small buffers, much smaller than the equivalent of 16 packets. This is what ping is doing for example, by setting SNDBUF to 324 bytes rounded up to 2kB by the kernel. The problem is that there is no documented method to force a specific packet to emit an interrupt (eg: the last of the ring) nor is it possible to make the NIC emit an interrupt after a given delay. In this case, it causes trouble, because when ping sends packets over its raw socket, the few first packets leave the system, and the first 15 packets will be emitted without an IRQ being generated, so without the skbs being freed. And since the socket's buffer is small, there's no way to reach that amount of packets, and the ping ends up with "send: no buffer available" after sending 6 packets. Running with 3 instances of ping in parallel is enough to hide the problem, because with 6 packets per instance, that's 18 packets total, which is enough to grant a Tx interrupt before all are sent. The original driver in the LSP kernel worked around this design flaw by using a software timer to clean up the Tx descriptors. This timer was slow and caused terrible network performance on some Tx-bound workloads (such as routing) but was enough to make tools like ping work correctly. Instead here, we simply set the packet counts before interrupt to 1. This ensures that each packet sent will produce an interrupt. NAPI takes care of coalescing interrupts since the interrupt is disabled once generated. No measurable performance impact nor CPU usage were observed on small nor large packets, including when saturating the link on Tx, and this fixes tools like ping which rely on too small a send buffer. If one wants to increase this value for certain workloads where it is safe to do so, "ethtool -C $dev tx-frames" will override this default setting. This fix needs to be applied to stable kernels starting with 3.10. Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16net/mlx4_core: Limit count field to 24 bits in qp_alloc_resJack Morgenstein
[ Upstream commit 2d5c57d7fbfaa642fb7f0673df24f32b83d9066c ] Some VF drivers use the upper byte of "param1" (the qp count field) in mlx4_qp_reserve_range() to pass flags which are used to optimize the range allocation. Under the current code, if any of these flags are set, the 32-bit count field yields a count greater than 2^24, which is out of range, and this VF fails. As these flags represent a "best-effort" allocation hint anyway, they may safely be ignored. Therefore, the PF driver may simply mask out the bits. Fixes: c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests" Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16tg3: fix ring init when there are more TX than RX channelsThadeu Lima de Souza Cascardo
[ Upstream commit a620a6bc1c94c22d6c312892be1e0ae171523125 ] If TX channels are set to 4 and RX channels are set to less than 4, using ethtool -L, the driver will try to initialize more RX channels than it has allocated, causing an oops. This fix only initializes the RX ring if it has been allocated. Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16Fix race condition between vxlan_sock_add and vxlan_sock_releaseMarcelo Leitner
[ Upstream commit 00c83b01d58068dfeb2e1351cca6fccf2a83fa8f ] Currently, when trying to reuse a socket, vxlan_sock_add will grab vn->sock_lock, locate a reusable socket, inc refcount and release vn->sock_lock. But vxlan_sock_release() will first decrement refcount, and then grab that lock. refcnt operations are atomic but as currently we have deferred works which hold vs->refcnt each, this might happen, leading to a use after free (specially after vxlan_igmp_leave): CPU 1 CPU 2 deferred work vxlan_sock_add ... ... spin_lock(&vn->sock_lock) vs = vxlan_find_sock(); vxlan_sock_release dec vs->refcnt, reaches 0 spin_lock(&vn->sock_lock) vxlan_sock_hold(vs), refcnt=1 spin_unlock(&vn->sock_lock) hlist_del_rcu(&vs->hlist); vxlan_notify_del_rx_port(vs) spin_unlock(&vn->sock_lock) So when we look for a reusable socket, we check if it wasn't freed already before reusing it. Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Fixes: 7c47cedf43a8b3 ("vxlan: move IGMP join/leave to work queue") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16sata_fsl: fix error handling of irq_of_parse_and_mapDmitry Torokhov
commit aad0b624129709c94c2e19e583b6053520353fa8 upstream. irq_of_parse_and_map() returns 0 on error (the result is unsigned int), so testing for negative result never works. Signed-off-by: Dmitry Torokhov <dtor@chromium.org> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16ahci: disable MSI on SAMSUNG 0xa800 SSDTejun Heo
commit 2b21ef0aae65f22f5ba86b13c4588f6f0c2dbefb upstream. Just like 0x1600 which got blacklisted by 66a7cbc303f4 ("ahci: disable MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes on NCQ commands if MSI is enabled. Disable MSI. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Dominik Mierzejewski <dominik@greysector.net> Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16AHCI: Add DeviceIDs for Sunrise Point-LP SATA controllerDevin Ryles
commit 249cd0a187ed4ef1d0af7f74362cc2791ec5581b upstream. This patch adds DeviceIDs for Sunrise Point-LP. Signed-off-by: Devin Ryles <devin.ryles@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16USB: xhci: Reset a halted endpoint immediately when we encounter a stall.Mathias Nyman
commit 8e71a322fdb127814bcba423a512914ca5bc6cf5 upstream. If a device is halted and reuturns a STALL, then the halted endpoint needs to be cleared both on the host and device side. The host side halt is cleared by issueing a xhci reset endpoint command. The device side is cleared with a ClearFeature(ENDPOINT_HALT) request, which should be issued by the device driver if a URB reruen -EPIPE. Previously we cleared the host side halt after the device side was cleared. To make sure the host side halt is cleared in time we want to issue the reset endpoint command immedialtely when a STALL status is encountered. Otherwise we end up not following the specs and not returning -EPIPE several times in a row when trying to transfer data to a halted endpoint. Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.) Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16media: smiapp: Only some selection targets are settableSakari Ailus
commit b31eb901c4e5eeef4c83c43dfbc7fe0d4348cb21 upstream. Setting a non-settable selection target caused BUG() to be called. The check for valid selections only takes the selection target into account, but does not tell whether it may be set, or only get. Fix the issue by simply returning an error to the user. Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16drm/i915: Unlock panel even when LVDS is disabledDaniel Vetter
commit b0616c5306b342ceca07044dbc4f917d95c4f825 upstream. Otherwise we'll have backtraces in assert_panel_unlocked because the BIOS locks the register. In the reporter's case this regression was introduced in commit c31407a3672aaebb4acddf90944a114fa5c8af7b Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Thu Oct 18 21:07:01 2012 +0100 drm/i915: Add no-lvds quirk for Supermicro X7SPA-H Reported-by: Alexey Orishko <alexey.orishko@gmail.com> Cc: Alexey Orishko <alexey.orishko@gmail.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Francois Tigeot <ftigeot@wolfpond.org> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Tested-by: Alexey Orishko <alexey.orishko@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16drm/i915: More cautious with pch fifo underrunsDaniel Vetter
commit b68362278af94e1171f5be9d4e44988601fb0439 upstream. Apparently PCH fifo underruns are tricky, we have plenty reports that we see the occasional underrun (especially at boot-up). So for a change let's see what happens when we don't re-enable pch fifo underrun reporting when the pipe is disabled. This means that the kernel can't catch pch fifo underruns when they happen (except when all pipes are on on the pch). But we'll still catch underruns when disabling the pipe again. So not a terrible reduction in test coverage. Since the DRM_ERROR is new and hence a regression plan B would be to revert it back to a debug output. Which would be a lot worse than this hack for underrun test coverage in the wild. See the referenced discussions for more. References: http://mid.gmane.org/CA+gsUGRfGe3t4NcjdeA=qXysrhLY3r4CEu7z4bjTwxi1uOfy+g@mail.gmail.com Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85898 References: https://bugs.freedesktop.org/show_bug.cgi?id=85898 References: https://bugs.freedesktop.org/show_bug.cgi?id=86233 References: https://bugs.freedesktop.org/show_bug.cgi?id=86478 Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Tested-by: lu hua <huax.lu@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with ↵Petr Mladek
3.18.0-rc6 commit f5475cc43c899e33098d4db44b7c5e710f16589d upstream. I was unable too boot 3.18.0-rc6 because of the following kernel panic in drm_calc_vbltimestamp_from_scanoutpos(): [drm] Initialized drm 1.1.0 20060810 [drm] radeon kernel modesetting enabled. [drm] initializing kernel modesetting (RV100 0x1002:0x515E 0x15D9:0x8080). [drm] register mmio base: 0xC8400000 [drm] register mmio size: 65536 radeon 0000:0b:01.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (16M used) radeon 0000:0b:01.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF [drm] Detected VRAM RAM=128M, BAR=128M [drm] RAM width 16bits DDR [TTM] Zone kernel: Available graphics memory: 3829346 kiB [TTM] Zone dma32: Available graphics memory: 2097152 kiB [TTM] Initializing pool allocator [TTM] Initializing DMA pool allocator [drm] radeon: 16M of VRAM memory ready [drm] radeon: 512M of GTT memory ready. [drm] GART: num cpu pages 131072, num gpu pages 131072 [drm] PCI GART of 512M enabled (table at 0x0000000037880000). radeon 0000:0b:01.0: WB disabled radeon 0000:0b:01.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffff8800bbbfa000 [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [drm] Driver supports precise vblank timestamp query. [drm] radeon: irq initialized. [drm] Loading R100 Microcode radeon 0000:0b:01.0: Direct firmware load for radeon/R100_cp.bin failed with error -2 radeon_cp: Failed to load firmware "radeon/R100_cp.bin" [drm:r100_cp_init] *ERROR* Failed to load firmware! radeon 0000:0b:01.0: failed initializing CP (-2). radeon 0000:0b:01.0: Disabling GPU acceleration [drm] radeon: cp finalized BUG: unable to handle kernel NULL pointer dereference at 000000000000025c IP: [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320 PGD 0 Oops: 0000 [#1] SMP Modules linked in: CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.18.0-rc6-4-default #2649 Hardware name: Supermicro X7DB8/X7DB8, BIOS 6.00 07/26/2006 task: ffff880234da2010 ti: ffff880234da4000 task.ti: ffff880234da4000 RIP: 0010:[<ffffffff8150423b>] [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320 RSP: 0000:ffff880234da7918 EFLAGS: 00010086 RAX: ffffffff81557890 RBX: 0000000000000000 RCX: ffff880234da7a48 RDX: ffff880234da79f4 RSI: 0000000000000000 RDI: ffff880232e15000 RBP: ffff880234da79b8 R08: 0000000000000000 R09: 0000000000000000 R10: 000000000000000a R11: 0000000000000001 R12: ffff880232dda1c0 R13: ffff880232e1518c R14: 0000000000000292 R15: ffff880232e15000 FS: 0000000000000000(0000) GS:ffff88023fc40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 000000000000025c CR3: 0000000002014000 CR4: 00000000000007e0 Stack: ffff880234da79d8 0000000000000286 ffff880232dcbc00 0000000000002480 ffff880234da7958 0000000000000296 ffff880234da7998 ffffffff8151b51d ffff880234da7a48 0000000032dcbeb0 ffff880232dcbc00 ffff880232dcbc58 Call Trace: [<ffffffff8151b51d>] ? drm_vma_offset_remove+0x1d/0x110 [<ffffffff8152dc98>] radeon_get_vblank_timestamp_kms+0x38/0x60 [<ffffffff8152076a>] ? ttm_bo_release_list+0xba/0x180 [<ffffffff81503751>] drm_get_last_vbltimestamp+0x41/0x70 [<ffffffff81503933>] vblank_disable_and_save+0x73/0x1d0 [<ffffffff81106b2f>] ? try_to_del_timer_sync+0x4f/0x70 [<ffffffff81505245>] drm_vblank_cleanup+0x65/0xa0 [<ffffffff815604fa>] radeon_irq_kms_fini+0x1a/0x70 [<ffffffff8156c07e>] r100_init+0x26e/0x410 [<ffffffff8152ae3e>] radeon_device_init+0x7ae/0xb50 [<ffffffff8152d57f>] radeon_driver_load_kms+0x8f/0x210 [<ffffffff81506965>] drm_dev_register+0xb5/0x110 [<ffffffff8150998f>] drm_get_pci_dev+0x8f/0x200 [<ffffffff815291cd>] radeon_pci_probe+0xad/0xe0 [<ffffffff8141a365>] local_pci_probe+0x45/0xa0 [<ffffffff8141b741>] pci_device_probe+0xd1/0x130 [<ffffffff81633dad>] driver_probe_device+0x12d/0x3e0 [<ffffffff8163413b>] __driver_attach+0x9b/0xa0 [<ffffffff816340a0>] ? __device_attach+0x40/0x40 [<ffffffff81631cd3>] bus_for_each_dev+0x63/0xa0 [<ffffffff8163378e>] driver_attach+0x1e/0x20 [<ffffffff81633390>] bus_add_driver+0x180/0x240 [<ffffffff81634914>] driver_register+0x64/0xf0 [<ffffffff81419cac>] __pci_register_driver+0x4c/0x50 [<ffffffff81509bf5>] drm_pci_init+0xf5/0x120 [<ffffffff821dc871>] ? ttm_init+0x6a/0x6a [<ffffffff821dc908>] radeon_init+0x97/0xb5 [<ffffffff810002fc>] do_one_initcall+0xbc/0x1f0 [<ffffffff810e3278>] ? __wake_up+0x48/0x60 [<ffffffff8218e256>] kernel_init_freeable+0x18a/0x215 [<ffffffff8218d983>] ? initcall_blacklist+0xc0/0xc0 [<ffffffff818a78f0>] ? rest_init+0x80/0x80 [<ffffffff818a78fe>] kernel_init+0xe/0xf0 [<ffffffff818c0c3c>] ret_from_fork+0x7c/0xb0 [<ffffffff818a78f0>] ? rest_init+0x80/0x80 Code: 45 ac 0f 88 a8 01 00 00 3b b7 d0 01 00 00 49 89 ff 0f 83 99 01 00 00 48 8b 47 20 48 8b 80 88 00 00 00 48 85 c0 0f 84 cd 01 00 00 <41> 8b b1 5c 02 00 00 41 8b 89 58 02 00 00 89 75 98 41 8b b1 60 RIP [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320 RSP <ffff880234da7918> CR2: 000000000000025c ---[ end trace ad2c0aadf48e2032 ]--- Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009 It has helped me to add a NULL pointer check that was suggested at http://lists.freedesktop.org/archives/dri-devel/2014-October/070663.html I am not familiar with the code. But the change looks sane and we need something fast at this stage of 3.18 development. Suggested-by: Helge Deller <deller@gmx.de> Signed-off-by: Petr Mladek <pmladek@suse.cz> Tested-by: Petr Mladek <pmladek@suse.cz> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16i2c: davinci: generate STP always when NACK is receivedGrygorii Strashko
commit 9ea359f7314132cbcb5a502d2d8ef095be1f45e4 upstream. According to I2C specification the NACK should be handled as follows: "When SDA remains HIGH during this ninth clock pulse, this is defined as the Not Acknowledge signal. The master can then generate either a STOP condition to abort the transfer, or a repeated START condition to start a new transfer." [I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf] Currently the Davinci i2c driver interrupts the transfer on receipt of a NACK but fails to send a STOP in some situations and so makes the bus stuck until next I2C IP reset (idle/enable). For example, the issue will happen during SMBus read transfer which consists from two i2c messages write command/address and read data: S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P <--- write -----------------------> <--- read ---------------------> The I2C client device will send NACK if it can't recognize "Command Code" and it's expected from I2C master to generate STP in this case. But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will not be generated. Hence, fix it by generating Stop condition (STP) always when NACK is received. This patch fixes Davinci I2C in the same way it was done for OMAP I2C commit cda2109a26eb ("i2c: omap: query STP always when NACK is received"). Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reported-by: Hein Tibosch <hein_tibosch@yahoo.es> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16i2c: omap: fix i207 errata handlingAlexander Kochetkov
commit ccfc866356674cb3a61829d239c685af6e85f197 upstream. commit 6d9939f651419a63e091105663821f9c7d3fec37 (i2c: omap: split out [XR]DR and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly Set) get handled. 6d9939f6514 code doesn't correspond to workaround provided by errata. According to errata ISR must filter out spurious RDR before data read not after. ISR must read RXSTAT to get number of bytes available to read. Because RDR could be set while there could no data in the receive FIFO. Restored pre 6d9939f6514 way of handling errata. Found by code review. Real impact haven't seen. Tested on Beagleboard XM C. Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com> Fixes: 6d9939f651419a63e09110 i2c: omap: split out [XR]DR and [XR]RDY Tested-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16i2c: omap: fix NACK and Arbitration Lost irq handlingAlexander Kochetkov
commit 27caca9d2e01c92b26d0690f065aad093fea01c7 upstream. commit 1d7afc95946487945cc7f5019b41255b72224b70 (i2c: omap: ack IRQ in parts) changed the interrupt handler to complete transfers without clearing XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be fired again. As a result, ISR keep processing transfer after it was already complete (from the driver code point of view). A didn't see real impacts of the 1d7afc9, but it is really bad idea to have ISR running on user data after transfer was complete. It looks, what 1d7afc9 violate TI specs in what how AL and NACK should be handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32). According to specs (if I understood correctly), in case of NACK and AL driver must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and NACK, AL, ARDY, and XDR (Master Transmitter Mode). All that is done down the code under the if condition: if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ... The patch restore pre 1d7afc9 logic of handling NACK and AL interrupts, so no interrupts is fired after ISR informs the rest of driver what transfer complete. Note: instead of removing break under NACK case, we could just replace 'break' with 'continue' and allow NACK transfer to finish using ARDY event. I found that NACK and ARDY bits usually set together. That case confirm TI wiki: http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK In order if someone interested in the event traces for NACK and AL cases, I sent them to mailing list. Tested on Beagleboard XM C. Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com> Fixes: 1d7afc9 i2c: omap: ack IRQ in parts Acked-by: Felipe Balbi <balbi@ti.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-16xen-netfront: Remove BUGs on paged skb data which crosses a page boundarySeth Forshee
commit 8d609725d4357f499e2103e46011308b32f53513 upstream. These BUGs can be erroneously triggered by frags which refer to tail pages within a compound page. The data in these pages may overrun the hardware page while still being contained within the compound page, but since compound_order() evaluates to 0 for tail pages the assertion fails. The code already iterates through subsequent pages correctly in this scenario, so the BUGs are unnecessary and can be removed. Fixes: f36c374782e4 ("xen/netfront: handle compound page fragments on transmit") Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06gpu/radeon: Set flag to indicate broken 64-bit MSIBenjamin Herrenschmidt
commit 91ed6fd2c383bb8f02d66e98b4a4d2f7207249dc upstream. Some radeon ASICs don't support all 64 address bits of MSIs despite advertising support for 64-bit MSIs in their configuration space. This breaks on systems such as IBM POWER7/8, where 64-bit MSIs can be assigned with some of the high address bits set. This makes use of the newly introduced "no_64bit_msi" flag in structure pci_dev to allow the MSI allocation code to fallback to 32-bit MSIs on those adapters. Adding Alex's review tag. Patch to the driver is identical to the reviewed one, I dropped the arch/powerpc hunk rewrote the subject and cset comment. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06drm/radeon: fix endian swapping in vbios fetch for tdp tableAlex Deucher
commit 28731d5818ae25b92d1fb82fe0ac196e97102c1b upstream. Value needs to be swapped on BE. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06bnx2fc: do not add shared skbs to the fcoe_rx_listMaurizio Lombardi
commit 01a4cc4d0cd6a836c7b923760e8eb1cbb6a47258 upstream. In some cases, the fcoe_rx_list may contains multiple instances of the same skb (the so called "shared skbs"). the bnx2fc_l2_rcv thread is a loop that extracts a skb from the list, modifies (and destroys) its content and then proceed to the next one. The problem is that if the skb is shared, the remaining instances will be corrupted. The solution is to use skb_share_check() before adding the skb to the fcoe_rx_list. [ 6286.808725] ------------[ cut here ]------------ [ 6286.808729] WARNING: at include/scsi/fc_frame.h:173 bnx2fc_l2_rcv_thread+0x425/0x450 [bnx2fc]() [ 6286.808748] Modules linked in: bnx2x(-) mdio dm_service_time bnx2fc cnic uio fcoe libfcoe 8021q garp stp mrp libfc llc scsi_transport_fc scsi_tgt sg iTCO_wdt iTCO_vendor_support coretemp kvm_intel kvm crct10dif_pclmul crc32_pclmul crc32c_intel e1000e ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper ptp cryptd hpilo serio_raw hpwdt lpc_ich pps_core ipmi_si pcspkr mfd_core ipmi_msghandler shpchp pcc_cpufreq mperf nfsd auth_rpcgss nfs_acl lockd sunrpc dm_multipath xfs libcrc32c ata_generic pata_acpi sd_mod crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit ata_piix drm_kms_helper ttm drm libata i2c_core hpsa dm_mirror dm_region_hash dm_log dm_mod [last unloaded: mdio] [ 6286.808750] CPU: 3 PID: 1304 Comm: bnx2fc_l2_threa Not tainted 3.10.0-121.el7.x86_64 #1 [ 6286.808750] Hardware name: HP ProLiant DL120 G7, BIOS J01 07/01/2013 [ 6286.808752] 0000000000000000 000000000b36e715 ffff8800deba1e00 ffffffff815ec0ba [ 6286.808753] ffff8800deba1e38 ffffffff8105dee1 ffffffffa05618c0 ffff8801e4c81888 [ 6286.808754] ffffe8ffff663868 ffff8801f402b180 ffff8801f56bc000 ffff8800deba1e48 [ 6286.808754] Call Trace: [ 6286.808759] [<ffffffff815ec0ba>] dump_stack+0x19/0x1b [ 6286.808762] [<ffffffff8105dee1>] warn_slowpath_common+0x61/0x80 [ 6286.808763] [<ffffffff8105e00a>] warn_slowpath_null+0x1a/0x20 [ 6286.808765] [<ffffffffa054f415>] bnx2fc_l2_rcv_thread+0x425/0x450 [bnx2fc] [ 6286.808767] [<ffffffffa054eff0>] ? bnx2fc_disable+0x90/0x90 [bnx2fc] [ 6286.808769] [<ffffffff81085aef>] kthread+0xcf/0xe0 [ 6286.808770] [<ffffffff81085a20>] ? kthread_create_on_node+0x140/0x140 [ 6286.808772] [<ffffffff815fc76c>] ret_from_fork+0x7c/0xb0 [ 6286.808773] [<ffffffff81085a20>] ? kthread_create_on_node+0x140/0x140 [ 6286.808774] ---[ end trace c6cdb939184ccb4e ]--- Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Acked-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06rt2x00: do not align payload on modern H/WStanislaw Gruszka
commit cfd9167af14eb4ec21517a32911d460083ee3d59 upstream. RT2800 and newer hardware require padding between header and payload if header length is not multiple of 4. For historical reasons we also align payload to to 4 bytes boundary, but such alignment is not needed on modern H/W. Patch fixes skb_under_panic problems reported from time to time: https://bugzilla.kernel.org/show_bug.cgi?id=84911 https://bugzilla.kernel.org/show_bug.cgi?id=72471 http://marc.info/?l=linux-wireless&m=139108549530402&w=2 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591 Panic happened because we eat 4 bytes of skb headroom on each (re)transmission when sending frame without the payload and the header length not being multiple of 4 (i.e. QoS header has 26 bytes). On such case because paylad_aling=2 is bigger than header_align=0 we increase header_align by 4 bytes. To prevent that we could change the check to: if (payload_length && payload_align > header_align) header_align += 4; but not aligning payload at all is more effective and alignment is not really needed by H/W (that has been tested on OpenWrt project for few years now). Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi> Debugged-by: Antti S. Lankila <alankila@bel.fi> Reported-by: Henrik Asp <solenskiner@gmail.com> Originally-From: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06can: dev: avoid calling kfree_skb() from interrupt contextThomas Körper
commit 5247a589c24022ab34e780039cc8000c48f2035e upstream. ikfree_skb() is Called in can_free_echo_skb(), which might be called from (TX Error) interrupt, which triggers the folloing warning: [ 1153.360705] ------------[ cut here ]------------ [ 1153.360715] WARNING: CPU: 0 PID: 31 at net/core/skbuff.c:563 skb_release_head_state+0xb9/0xd0() [ 1153.360772] Call Trace: [ 1153.360778] [<c167906f>] dump_stack+0x41/0x52 [ 1153.360782] [<c105bb7e>] warn_slowpath_common+0x7e/0xa0 [ 1153.360784] [<c158b909>] ? skb_release_head_state+0xb9/0xd0 [ 1153.360786] [<c158b909>] ? skb_release_head_state+0xb9/0xd0 [ 1153.360788] [<c105bc42>] warn_slowpath_null+0x22/0x30 [ 1153.360791] [<c158b909>] skb_release_head_state+0xb9/0xd0 [ 1153.360793] [<c158be90>] skb_release_all+0x10/0x30 [ 1153.360795] [<c158bf06>] kfree_skb+0x36/0x80 [ 1153.360799] [<f8486938>] ? can_free_echo_skb+0x28/0x40 [can_dev] [ 1153.360802] [<f8486938>] can_free_echo_skb+0x28/0x40 [can_dev] [ 1153.360805] [<f849a12c>] esd_pci402_interrupt+0x34c/0x57a [esd402] [ 1153.360809] [<c10a75b5>] handle_irq_event_percpu+0x35/0x180 [ 1153.360811] [<c10a7623>] ? handle_irq_event_percpu+0xa3/0x180 [ 1153.360813] [<c10a7731>] handle_irq_event+0x31/0x50 [ 1153.360816] [<c10a9c7f>] handle_fasteoi_irq+0x6f/0x120 [ 1153.360818] [<c10a9c10>] ? handle_edge_irq+0x110/0x110 [ 1153.360822] [<c1011b61>] handle_irq+0x71/0x90 [ 1153.360823] <IRQ> [<c168152c>] do_IRQ+0x3c/0xd0 [ 1153.360829] [<c1680b6c>] common_interrupt+0x2c/0x34 [ 1153.360834] [<c107d277>] ? finish_task_switch+0x47/0xf0 [ 1153.360836] [<c167c27b>] __schedule+0x35b/0x7e0 [ 1153.360839] [<c10a5334>] ? console_unlock+0x2c4/0x4d0 [ 1153.360842] [<c13df500>] ? n_tty_receive_buf_common+0x890/0x890 [ 1153.360845] [<c10707b6>] ? process_one_work+0x196/0x370 [ 1153.360847] [<c167c723>] schedule+0x23/0x60 [ 1153.360849] [<c1070de1>] worker_thread+0x161/0x460 [ 1153.360852] [<c1090fcf>] ? __wake_up_locked+0x1f/0x30 [ 1153.360854] [<c1070c80>] ? rescuer_thread+0x2f0/0x2f0 [ 1153.360856] [<c1074f01>] kthread+0xa1/0xc0 [ 1153.360859] [<c1680401>] ret_from_kernel_thread+0x21/0x30 [ 1153.360861] [<c1074e60>] ? kthread_create_on_node+0x110/0x110 [ 1153.360863] ---[ end trace 5ff83639cbb74b35 ]--- This patch replaces the kfree_skb() by dev_kfree_skb_any(). Signed-off-by: Thomas Körper <thomas.koerper@esd.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06scsi: add Intel Multi-Flex to scsi scan blacklistChristian Sünkenberg
commit 1899045510ff109980d9cc34e330fd8ca3631871 upstream. Intel Multi-Flex LUNs choke on REPORT SUPPORTED OPERATION CODES resulting in sd_mod hanging for several minutes on startup. The issue was introduced with WRITE SAME discovery heuristics. Fixes: 5db44863b6eb ("[SCSI] sd: Implement support for WRITE SAME") Signed-off-by: Christian Sünkenberg <christian.suenkenberg@hfg-karlsruhe.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06vhost-scsi: Take configfs group dependency during VHOST_SCSI_SET_ENDPOINTNicholas Bellinger
commit ab8edab132829b26dd13db6caca3c242cce35dc1 upstream. This patch addresses a bug where individual vhost-scsi configfs endpoint groups can be removed from below while active exports to QEMU userspace still exist, resulting in an OOPs. It adds a configfs_depend_item() in vhost_scsi_set_endpoint() to obtain an explicit dependency on se_tpg->tpg_group in order to prevent individual vhost-scsi WWPN endpoints from being released via normal configfs methods while an QEMU ioctl reference still exists. Also, add matching configfs_undepend_item() in vhost_scsi_clear_endpoint() to release the dependency, once QEMU's reference to the individual group at /sys/kernel/config/target/vhost/$WWPN/$TPGT is released. (Fix up vhost_scsi_clear_endpoint() error path - DanC) Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06spi: dw: Fix dynamic speed change.Thor Thayer
commit 0a8727e69778683495058852f783eeda141a754e upstream. An IOCTL call that calls spi_setup() and then dw_spi_setup() will overwrite the persisted last transfer speed. On each transfer, the SPI speed is compared to the last transfer speed to determine if the clock divider registers need to be updated (did the speed change?). This bug was observed with the spidev driver using spi-config to update the max transfer speed. This fix: Don't overwrite the persisted last transaction clock speed when updating the SPI parameters in dw_spi_setup(). On the next transaction, the new speed won't match the persisted last speed and the hardware registers will be updated. On initialization, the persisted last transaction clock speed will be 0 but will be updated after the first SPI transaction. Move zeroed clock divider check into clock change test because chip->clk_div is zero on startup and would cause a divide-by-zero error. The calculation was wrong as well (can't support odd #). Reported-by: Vlastimil Setka <setka@vsis.cz> Signed-off-by: Vlastimil Setka <setka@vsis.cz> Signed-off-by: Thor Thayer <tthayer@opensource.altera.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06iser-target: Disable TX completion interrupt coalescingNicholas Bellinger
commit 0d0f660d882c1c02748ced13966a2413aa5d6cc2 upstream. This patch explicitly disables TX completion interrupt coalescing logic in isert_put_response() and isert_put_datain() that was originally added as an efficiency optimization in commit 95b60f07. It has been reported that this change can trigger ABORT_TASK timeouts under certain small block workloads, where disabling coalescing was required for stability. According to Sagi, this doesn't impact overall performance, so go ahead and disable it for now. Reported-by: Moussa Ba <moussaba@micron.com> Reported-by: Sagi Grimberg <sagig@dev.mellanox.co.il> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06Target/iser: Fix a wrong dereference in case discovery session is over iserSagi Grimberg
commit e0546fc1ba66c90cb38a5764357366267d3e58e4 upstream. In case the discovery session is carried over iser, we can't access the assumed network portal since the default portal is used. In this case we don't really need to allocate the fastreg pool, just prepare to the text pdu that will follow. Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Reported-by: Alex Tabachnik <alext@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06iser-target: Handle DEVICE_REMOVAL event on network portal listener correctlySagi Grimberg
commit 3b726ae2de02a406cc91903f80132daee37b6f1b upstream. In this case the cm_id->context is the isert_np, and the cm_id->qp is NULL, so use that to distinct the cases. Since we don't expect any other events on this cm_id we can just return -1 for explicit termination of the cm_id by the cma layer. Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06target: Don't call TFO->write_pending if data_length == 0Roland Dreier
commit 885e7b0e181c14e4d0ddd26c688bad2b84c1ada9 upstream. If an initiator sends a zero-length command (e.g. TEST UNIT READY) but sets the transfer direction in the transport layer to indicate a data-out phase, we still shouldn't try to transfer data. At best it's a NOP, and depending on the transport, we might crash on an uninitialized sg list. Reported-by: Craig Watson <craig.watson@vanguard-rugged.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06srp-target: Retry when QP creation fails with ENOMEMBart Van Assche
commit ab477c1ff5e0a744c072404bf7db51bfe1f05b6e upstream. It is not guaranteed to that srp_sq_size is supported by the HCA. So if we failed to create the QP with ENOMEM, try with a smaller srp_sq_size. Keep it up until we hit MIN_SRPT_SQ_SIZE, then fail the connection. Reported-by: Mark Lehrer <lehrer@gmail.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06Input: xpad - use proper endpoint typeGreg Kroah-Hartman
commit a1f9a4072655843fc03186acbad65990cc05dd2d upstream. The xpad wireless endpoint is not a bulk endpoint on my devices, but rather an interrupt one, so the USB core complains when it is submitted. I'm guessing that the author really did mean that this should be an interrupt urb, but as there are a zillion different xpad devices out there, let's cover out bases and handle both bulk and interrupt endpoints just as easily. Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06Input: synaptics - adjust min/max on Thinkpad E540Ben Sagal
commit bce4f9e764c36bc35dd5c9cf9e057c09f422397d upstream. The LEN2006 Synaptics touchpad (as found in Thinkpad E540) returns wrong min max values. touchpad-edge-detector output: > Touchpad SynPS/2 Synaptics TouchPad on /dev/input/event6 > Move one finger around the touchpad to detect the actual edges > Kernel says: x [1472..5674], y [1408..4684] > Touchpad sends: x [1264..5675], y [1171..4688] Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88211 Signed-off-by: Binyamin Sagal <bensagal@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06can: esd_usb2: fix memory leak on disconnectAlexey Khoroshilov
commit efbd50d2f62fc1f69a3dcd153e63ba28cc8eb27f upstream. It seems struct esd_usb2 dev is not deallocated on disconnect. The patch adds the missing deallocation. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06usb: xhci: rework root port wake bits if controller isn't allowed to wakeupLu Baolu
commit a1377e5397ab321e21b793ec8cd2b6f12bd3c718 upstream. When system is being suspended, if host device is not allowed to do wakeup, xhci_suspend() needs to clear all root port wake on bits. Otherwise, some platforms may generate spurious wakeup, even if PCI PME# is disabled. The initial commit ff8cbf250b44 ("xhci: clear root port wake on bits"), which also got into stable, turned out to not work correctly and had to be reverted, and is now rewritten. Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> [Mathias Nyman: reword commit message] Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06USB: xhci: don't start a halted endpoint before its new dequeue is setMathias Nyman
commit c3492dbfa1050debf23a5b5cd2bc7514c5b37896 upstream. A halted endpoint ring must first be reset, then move the ring dequeue pointer past the problematic TRB. If we start the ring too early after reset, but before moving the dequeue pointer we will end up executing the same problematic TRB again. As we always issue a set transfer dequeue command after a reset endpoint command we can skip starting endpoint rings at reset endpoint command completion. Without this fix we end up trying to handle the same faulty TD for contol endpoints. causing timeout, and failing testusb ctrl_out write tests. Fixes: e9df17e (USB: xhci: Correct assumptions about number of rings per endpoint.) Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06usb-quirks: Add reset-resume quirk for MS Wireless Laser Mouse 6000Hans de Goede
commit 263e80b43559a6103e178a9176938ce171b23872 upstream. This wireless mouse receiver needs a reset-resume quirk to properly come out of reset. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1165206 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06usb: serial: ftdi_sio: add PIDs for Matrix Orbital productsTroy Clark
commit 204ec6e07ea7aff863df0f7c53301f9cbbfbb9d3 upstream. Add PIDs for new Matrix Orbital GTT series products. Signed-off-by: Troy Clark <tclark@matrixorbital.ca> [johan: shorten commit message ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06USB: serial: cp210x: add IDs for CEL MeshConnect USB StickPreston Fick
commit ffcfe30ebd8dd703d0fc4324ffe56ea21f5479f4 upstream. Signed-off-by: Preston Fick <pffick@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06USB: keyspan: fix tty line-status reportingJohan Hovold
commit 5d1678a33c731b56e245e888fdae5e88efce0997 upstream. Fix handling of TTY error flags, which are not bitmasks and must specifically not be ORed together as this prevents the line discipline from recognising them. Also insert null characters when reporting overrun errors as these are not associated with the received character. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06USB: keyspan: fix overrun-error reportingJohan Hovold
commit 855515a6d3731242d85850a206f2ec084c917338 upstream. Fix reporting of overrun errors, which are not associated with a character. Instead insert a null character and report only once. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06USB: ssu100: fix overrun-error reportingJohan Hovold
commit 75bcbf29c284dd0154c3e895a0bd1ef0e796160e upstream. Fix reporting of overrun errors, which should only be reported once using the inserted null character. Fixes: 6b8f1ca5581b ("USB: ssu100: set tty_flags in ssu100_process_packet") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06staging: r8188eu: Add new device ID for DLink GO-USB-N150Larry Finger
commit 6d4556fc0309608f760f1d329df56d77fdd0c31a upstream. The DLink GO-USB-N150 with revision B1 uses this driver. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06of/base: Fix PowerPC address parsing hackBenjamin Herrenschmidt
commit 746c9e9f92dde2789908e51a354ba90a1962a2eb upstream. We have a historical hack that treats missing ranges properties as the equivalent of an empty one. This is needed for ancient PowerMac "bad" device-trees, and shouldn't be enabled for any other PowerPC platform, otherwise we get some nasty layout of devices in sysfs or even duplication when a set of otherwise identically named devices is created multiple times under a different parent node with no ranges property. This fix is needed for the PowerNV i2c busses to be exposed properly and will fix a number of other embedded cases. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06ath9k: Fix RTC_DERIVED_CLK usageMiaoqing Pan
commit 4e6ce4dc7ce71d0886908d55129d5d6482a27ff9 upstream. Based on the reference clock, which could be 25MHz or 40MHz, AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550. But, when a chip reset is done, processing the initvals sets the register back to the default value. Fix this by moving the code in ath9k_hw_init_pll() to ar9003_hw_override_ini(). Also, do this override for AR9531. Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06ib_isert: Add max_send_sge=2 minimum for control PDU responsesOr Gerlitz
commit f57915cfa5b2b14c1cffa2e83c034f55e3f0e70d upstream. This patch adds a max_send_sge=2 minimum in isert_conn_setup_qp() to ensure outgoing control PDU responses with tx_desc->num_sge=2 are able to function correctly. This addresses a bug with RDMA hardware using dev_attr.max_sge=3, that in the original code with the ConnectX-2 work-around would result in isert_conn->max_sge=1 being negotiated. Originally reported by Chris with ocrdma driver. Reported-by: Chris Moore <Chris.Moore@emulex.com> Tested-by: Chris Moore <Chris.Moore@emulex.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06IB/isert: Adjust CQ size to HW limitsChris Moore
commit b1a5ad006b34ded9dc7ec64988deba1b3ecad367 upstream. isert has an issue of trying to create a CQ with more CQEs than are supported by the hardware, that currently results in failures during isert_device creation during first session login. This is the isert version of the patch that Minh Tran submitted for iser, and is simple a workaround required to function with existing ocrdma hardware. Signed-off-by: Chris Moore <chris.moore@emulex.com> Reviewied-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06clockevent: sun4i: Fix race condition in the probe codeMaxime Ripard
commit 6bab4a8a1888729f17f4923cc5867e4674f66333 upstream. The interrupts were activated and the handler registered before the clockevent was registered in the probe function. The interrupt handler, however, was making the assumption that the clockevent device was registered. That could cause a null pointer dereference if the timer interrupt was firing during this narrow window. Fix that by moving the clockevent registration before the interrupt is enabled. Reported-by: Roman Byshko <rbyshko@gmail.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06PCI/MSI: Add device flag indicating that 64-bit MSIs don't workBenjamin Herrenschmidt
commit f144d1496b47e7450f41b767d0d91c724c2198bc upstream. This can be set by quirks/drivers to be used by the architecture code that assigns the MSI addresses. We additionally add verification in the core MSI code that the values assigned by the architecture do satisfy the limitation in order to fail gracefully if they don't (ie. the arch hasn't been updated to deal with that quirk yet). Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-12-06PCI: Support 64-bit bridge windows if we have 64-bit dma_addr_tYinghai Lu
commit 7fc986d8a9727e5d40da3c2c1c343da6142e82a9 upstream. Aaron reported that a 32-bit x86 kernel with Physical Address Extension (PAE) support complains about bridge prefetchable memory windows above 4GB: pci_bus 0000:00: root bus resource [mem 0x380000000000-0x383fffffffff] ... pci 0000:03:00.0: reg 0x10: [mem 0x383fffc00000-0x383fffdfffff 64bit pref] pci 0000:03:00.0: reg 0x20: [mem 0x383fffe04000-0x383fffe07fff 64bit pref] pci 0000:03:00.1: reg 0x10: [mem 0x383fffa00000-0x383fffbfffff 64bit pref] pci 0000:03:00.1: reg 0x20: [mem 0x383fffe00000-0x383fffe03fff 64bit pref] pci 0000:00:02.2: PCI bridge to [bus 03-04] pci 0000:00:02.2: bridge window [io 0x1000-0x1fff] pci 0000:00:02.2: bridge window [mem 0x91900000-0x91cfffff] pci 0000:00:02.2: can't handle 64-bit address space for bridge In this kernel, unsigned long is 32 bits and dma_addr_t is 64 bits. Previously we used "unsigned long" to hold the bridge window address. But this is a bus address, so we should use dma_addr_t instead. Use dma_addr_t to hold the bridge window base and limit. The question of whether the CPU can actually *address* the window is separate and depends on what the physical address space of the CPU is and whether the host bridge does any address translation. [bhelgaas: fix "shift count > width of type", changelog, stable tag] Fixes: d56dbf5bab8c ("PCI: Allocate 64-bit BARs above 4G when possible") Link: https://bugzilla.kernel.org/show_bug.cgi?id=88131 Reported-by: Aaron Ma <mapengyu@gmail.com> Tested-by: Aaron Ma <mapengyu@gmail.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-09-29 17:40:24 +0000