summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2015-08-10drm/nouveau/drm/nv04-nv40/instmem: protect access to priv->heap by mutexKamil Dudka
commit 7512223b1ece29a5968ed8b67ccb891d21b7834b upstream. This fixes the list_del corruption reported at <https://bugzilla.redhat.com/1205985>. Signed-off-by: Kamil Dudka <kdudka@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10drm/nouveau: hold mutex when calling nouveau_abi16_fini()Kamil Dudka
commit ac8c79304280da6ef05c348a9da03ab04898b994 upstream. This was the only access to cli->abi16 without holding the mutex. Signed-off-by: Kamil Dudka <kdudka@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10drm/nouveau/kms/nv50-: guard against enabling cursor on disabled headsBen Skeggs
commit 697bb728d9e2367020aa0c5af7363809d7658e43 upstream. Userspace has started doing this, which upsets the display class hw error checking in various unpleasant ways. Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10drm/nouveau/fbcon/nv11-: correctly account for ring space usageIlia Mirkin
commit d108142c0840ce389cd9898aa76943b3fb430b83 upstream. The RING_SPACE macro accounts how much space is used up so it's important to ask it for the right amount. Incorrect accounting of this can cause page faults down the line as writes are attempted outside of the ring. Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10qla2xxx: kill sessions/log out initiator on RSCN and port down eventsRoland Dreier
commit b2032fd567326ad0b2d443bb6d96d2580ec670a5 upstream. To fix some issues talking to ESX, this patch modifies the qla2xxx driver so that it never logs into remote ports. This has the side effect of getting rid of the "rports" entirely, which means we never log out of initiators and never tear down sessions when an initiator goes away. This is mostly OK, except that we can run into trouble if we have initiator A assigned FC address X:Y:Z by the fabric talking to us, and then initiator A goes away. Some time (could be a long time) later, initiator B comes along and also gets FC address X:Y:Z (which is available again, because initiator A is gone). If initiator B starts talking to us, then we'll still have the session for initiator A, and since we look up incoming IO based on the FC address X:Y:Z, initiator B will end up using ACLs for initiator A. Fix this by: 1. Handling RSCN events somewhat differently; instead of completely skipping the processing of fcports, we look through the list, and if an fcport disappears, we tell the target code the tear down the session and tell the HBA FW to release the N_Port handle. 2. Handling "port down" events by flushing all of our sessions. The firmware was already releasing the N_Port handle but we want the target code to drop all the sessions too. Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Alexei Potashnik <alexei@purestorage.com> Acked-by: Quinn Tran <quinn.tran@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10qla2xxx: fix command initialization in target mode.Kanoj Sarcar
commit 9fce12540cb9f91e7f1f539a80b70f0b388bdae0 upstream. Signed-off-by: Kanoj Sarcar <kanoj.sarcar@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10qla2xxx: Remove msleep in qlt_send_term_exchangeHimanshu Madhani
commit 6bc85dd595a5438b50ec085668e53ef26058bb90 upstream. Remove unnecessary msleep from qlt_send_term_exchange as it adds latency of 250 msec while sending terminate exchange to an aborted task. Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10qla2xxx: release request queue reservation.Quinn Tran
commit 810e30bc4658e9c069577bde52394a5af872803c upstream. Request IOCB queue element(s) is reserved during good path IO. Under error condition such as unable to allocate IOCB handle condition, the IOCB count that was reserved is not released. Signed-off-by: Quinn Tran <quinn.tran@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10qla2xxx: Fix hardware lock/unlock issue causing kernel panic.Saurav Kashyap
commit ba9f6f64a0ff6b7ecaed72144c179061f8eca378 upstream. [ Upstream commit ef86cb2059a14b4024c7320999ee58e938873032 ] This patch fixes a kernel panic for qla2xxx Target core Module driver introduced by a fix in the qla2xxx initiator code. Commit ef86cb2 ("qla2xxx: Mark port lost when we receive an RSCN for it.") introduced the regression for qla2xxx Target driver. Stack trace will have following signature --- <NMI exception stack> --- [ffff88081faa3cc8] _raw_spin_lock_irqsave at ffffffff815b1f03 [ffff88081faa3cd0] qlt_fc_port_deleted at ffffffffa096ccd0 [qla2xxx] [ffff88081faa3d20] qla2x00_schedule_rport_del at ffffffffa0913831[qla2xxx] [ffff88081faa3d50] qla2x00_mark_device_lost at ffffffffa09159c5[qla2xxx] [ffff88081faa3db0] qla2x00_async_event at ffffffffa0938d59 [qla2xxx] [ffff88081faa3e30] qla24xx_msix_default at ffffffffa093a326 [qla2xxx] [ffff88081faa3e90] handle_irq_event_percpu at ffffffff810a7b8d [ffff88081faa3ee0] handle_irq_event at ffffffff810a7d32 [ffff88081faa3f10] handle_edge_irq at ffffffff810ab6b9 [ffff88081faa3f30] handle_irq at ffffffff8100619c [ffff88081faa3f70] do_IRQ at ffffffff815b4b1c --- <IRQ stack> --- Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10intel_pstate: Add get_scaling cpu_defaults param to Knights LandingLukasz Anaczkowski
commit 69cefc273f942bd7bb347a02e8b5b738d5f6e6f3 upstream. Scaling for Knights Landing is same as the default scaling (100000). When Knigts Landing support was added to the pstate driver, this parameter was omitted resulting in a kernel panic during boot. Fixes: b34ef932d79a (intel_pstate: Knights Landing support) Reported-by: Yasuaki Ishimatsu <yishimat@redhat.com> Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com> Signed-off-by: Lukasz Anaczkowski <lukasz.anaczkowski@intel.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10iscsi-target: Fix iser explicit logout TX kthread leakNicholas Bellinger
commit 007d038bdf95ccfe2491d0078be54040d110fd06 upstream. This patch fixes a regression introduced with the following commit in v4.0-rc1 code, where an explicit iser-target logout would result in ->tx_thread_active being incorrectly cleared by the logout post handler, and subsequent TX kthread leak: commit 88dcd2dab5c23b1c9cfc396246d8f476c872f0ca Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Feb 26 22:19:15 2015 -0800 iscsi-target: Convert iscsi_thread_set usage to kthread.h To address this bug, change iscsit_logout_post_handler_closesession() and iscsit_logout_post_handler_samecid() to only cmpxchg() on ->tx_thread_active for traditional iscsi/tcp connections. This is required because iscsi/tcp connections are invoking logout post handler logic directly from TX kthread context, while iser connections are invoking logout post handler logic from a seperate workqueue context. Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10iscsi-target: Fix iscsit_start_kthreads failure OOPsNicholas Bellinger
commit e54198657b65625085834847ab6271087323ffea upstream. This patch fixes a regression introduced with the following commit in v4.0-rc1 code, where a iscsit_start_kthreads() failure triggers a NULL pointer dereference OOPs: commit 88dcd2dab5c23b1c9cfc396246d8f476c872f0ca Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Feb 26 22:19:15 2015 -0800 iscsi-target: Convert iscsi_thread_set usage to kthread.h To address this bug, move iscsit_start_kthreads() immediately preceeding the transmit of last login response, before signaling a successful transition into full-feature-phase within existing iscsi_target_do_tx_login_io() logic. This ensures that no target-side resource allocation failures can occur after the final login response has been successfully sent. Also, it adds a iscsi_conn->rx_login_comp to allow the RX thread to sleep to prevent other socket related failures until the final iscsi_post_login_handler() call is able to complete. Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10iscsi-target: Fix use-after-free during TPG session shutdownNicholas Bellinger
commit 417c20a9bdd1e876384127cf096d8ae8b559066c upstream. This patch fixes a use-after-free bug in iscsit_release_sessions_for_tpg() where se_portal_group->session_lock was incorrectly released/re-acquired while walking the active se_portal_group->tpg_sess_list. The can result in a NULL pointer dereference when iscsit_close_session() shutdown happens in the normal path asynchronously to this code, causing a bogus dereference of an already freed list entry to occur. To address this bug, walk the session list checking for the same state as before, but move entries to a local list to avoid dropping the lock while walking the active list. As before, signal using iscsi_session->session_restatement=1 for those list entries to be released locally by iscsit_free_session() code. Reported-by: Sunilkumar Nadumuttlu <sjn@datera.io> Cc: Sunilkumar Nadumuttlu <sjn@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10IB/ipoib: Fix CONFIG_INFINIBAND_IPOIB_CMJason Gunthorpe
commit efc1eedbf63a194b3b576fc25776f3f1fa55a4d4 upstream. If the above is turned off then ipoib_cm_dev_init unconditionally returns ENOSYS, and the newly added error handling in 0b3957 prevents ipoib from coming up at all: kernel: mlx4_0: ipoib_transport_dev_init failed kernel: mlx4_0: failed to initialize port 1 (ret = -12) Fixes: 0b39578bcde4 (IB/ipoib: Use dedicated workqueues per interface) Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10hwmon: (nct7904) Rename pwm attributes to match hwmon ABIGuenter Roeck
commit 0d6aaffc3a6db642e0a165ba4d17d6d7bbaf5201 upstream. pwm attributes have well defined names, which should be used. Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10hwmon: (nct7802) Fix integer overflow seen when writing voltage limitsGuenter Roeck
commit 9200bc4c28cd8992eb5379345abd6b4f0c93df16 upstream. Writing a large value into a voltage limit attribute can result in an overflow due to an auto-conversion from unsigned long to unsigned int. Cc: Constantine Shulyupin <const@MakeLinux.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10vhost: actually track log eventfd fileMarc-André Lureau
commit 7932c0bd7740f4cd2aa168d3ce0199e7af7d72d5 upstream. While reviewing vhost log code, I found out that log_file is never set. Note: I haven't tested the change (QEMU doesn't use LOG_FD yet). Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10n_tty: signal and flush atomicallyPeter Hurley
commit 3b19e032295647b7be2aa3be62510db4aaeda759 upstream. When handling signalling char, claim the termios write lock before signalling waiting readers and writers to prevent further i/o before flushing the echo and output buffers. This prevents a userspace signal handler which may output from racing the terminal flush. Reference: Bugzilla #99351 ("Output truncated in ssh session after...") Fixes: commit d2b6f44779d3 ("n_tty: Fix signal handling flushes") Reported-by: Filipe Brandenburger <filbranden@google.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10efi: Check for NULL efi kernel parametersRicardo Neri
commit 9115c7589b11349a1c3099758b4bded579ff69e0 upstream. Even though it is documented how to specifiy efi parameters, it is possible to cause a kernel panic due to a dereference of a NULL pointer when parsing such parameters if "efi" alone is given: PANIC: early exception 0e rip 10:ffffffff812fb361 error 0 cr2 0 [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.2.0-rc1+ #450 [ 0.000000] ffffffff81fe20a9 ffffffff81e03d50 ffffffff8184bb0f 00000000000003f8 [ 0.000000] 0000000000000000 ffffffff81e03e08 ffffffff81f371a1 64656c62616e6520 [ 0.000000] 0000000000000069 000000000000005f 0000000000000000 0000000000000000 [ 0.000000] Call Trace: [ 0.000000] [<ffffffff8184bb0f>] dump_stack+0x45/0x57 [ 0.000000] [<ffffffff81f371a1>] early_idt_handler_common+0x81/0xae [ 0.000000] [<ffffffff812fb361>] ? parse_option_str+0x11/0x90 [ 0.000000] [<ffffffff81f4dd69>] arch_parse_efi_cmdline+0x15/0x42 [ 0.000000] [<ffffffff81f376e1>] do_early_param+0x50/0x8a [ 0.000000] [<ffffffff8106b1b3>] parse_args+0x1e3/0x400 [ 0.000000] [<ffffffff81f37a43>] parse_early_options+0x24/0x28 [ 0.000000] [<ffffffff81f37691>] ? loglevel+0x31/0x31 [ 0.000000] [<ffffffff81f37a78>] parse_early_param+0x31/0x3d [ 0.000000] [<ffffffff81f3ae98>] setup_arch+0x2de/0xc08 [ 0.000000] [<ffffffff8109629a>] ? vprintk_default+0x1a/0x20 [ 0.000000] [<ffffffff81f37b20>] start_kernel+0x90/0x423 [ 0.000000] [<ffffffff81f37495>] x86_64_start_reservations+0x2a/0x2c [ 0.000000] [<ffffffff81f37582>] x86_64_start_kernel+0xeb/0xef [ 0.000000] RIP 0xffffffff81ba2efc This panic is not reproducible with "efi=" as this will result in a non-NULL zero-length string. Thus, verify that the pointer to the parameter string is not NULL. This is consistent with other parameter-parsing functions which check for NULL pointers. Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Cc: Dave Young <dyoung@redhat.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10efi: Handle memory error structures produced based on old versions of standardLuck, Tony
commit 4c62360d7562a20c996836d163259c87d9378120 upstream. The memory error record structure includes as its first field a bitmask of which subsequent fields are valid. The allows new fields to be added to the structure while keeping compatibility with older software that parses these records. This mechanism was used between versions 2.2 and 2.3 to add four new fields, growing the size of the structure from 73 bytes to 80. But Linux just added all the new fields so this test: if (gdata->error_data_length >= sizeof(*mem_err)) cper_print_mem(newpfx, mem_err); else goto err_section_too_small; now make Linux complain about old format records being too short. Add a definition for the old format of the structure and use that for the minimum size check. Pass the actual size to cper_print_mem() so it can sanity check the validation_bits field to ensure that if a BIOS using the old format sets bits as if it were new, we won't access fields beyond the end of the structure. Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10mei: prevent unloading mei hw modules while the device is opened.Tomas Winkler
commit 154322f47376fed6ab1e4b350aa45fffa15a61aa upstream. chrdev_open() increases reference counter on cdev->owner. Instead of assigning the owner to mei subsystem, the owner has to be set to the underlaying HW module (mei_me or mei_txe), so once the device is opened the HW module cannot be unloaded. Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10xhci: do not report PLC when link is in internal resume stateZhuang Jin Can
commit aca3a0489ac019b58cf32794d5362bb284cb9b94 upstream. Port link change with port in resume state should not be reported to usbcore, as this is an internal state to be handled by xhci driver. Reporting PLC to usbcore may cause usbcore clearing PLC first and port change event irq won't be generated. Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10xhci: prevent bus_suspend if SS port resuming in phase 1Zhuang Jin Can
commit fac4271d1126c45ceaceb7f4a336317b771eb121 upstream. When the link is just waken, it's in Resume state, and driver sets PLS to U0. This refers to Phase 1. Phase 2 refers to when the link has completed the transition from Resume state to U0. With the fix of xhci: report U3 when link is in resume state, it also exposes an issue that usb3 roothub and controller can suspend right after phase 1, and this causes a hard hang in controller. To fix the issue, we need to prevent usb3 bus suspend if any port is resuming in phase 1. [merge separate USB2 and USB3 port resume checking to one -Mathias] Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10xhci: report U3 when link is in resume stateZhuang Jin Can
commit 243292a2ad3dc365849b820a64868927168894ac upstream. xhci_hub_report_usb3_link_state() returns pls as U0 when the link is in resume state, and this causes usb core to think the link is in U0 while actually it's in resume state. When usb core transfers control request on the link, it fails with TRB error as the link is not ready for transfer. To fix the issue, report U3 when the link is in resume state, thus usb core knows the link it's not ready for transfer. Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10xhci: Calculate old endpoints correctly on device resetBrian Campbell
commit 326124a027abc9a7f43f72dc94f6f0f7a55b02b3 upstream. When resetting a device the number of active TTs may need to be corrected by xhci_update_tt_active_eps, but the number of old active endpoints supplied to it was always zero, so the number of TTs and the bandwidth reserved for them was not updated, and could rise unnecessarily. This affected systems using Intel's Patherpoint chipset, which rely on software bandwidth checking. For example, a Lenovo X230 would lose the ability to use ports on the docking station after enough suspend/resume cycles because the bandwidth calculated would rise with every cycle when a suitable device is attached. The correct number of active endpoints is calculated in the same way as in xhci_reserve_bandwidth. Signed-off-by: Brian Campbell <bacam@z273.org.uk> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10serial: core: Fix crashes while echoing when closingPeter Hurley
commit e144c58cad6667876173dd76977e9e6557e34941 upstream. While closing, new rx data may be received after the input buffers have been flushed but before stop_rx() halts receiving [1]. The new data might not be processed by flush_to_ldisc() until after uart_shutdown() and normal input processing is re-enabled (ie., tty->closing = 0). The race is outlined below: CPU 0 | CPU 1 | uart_close() | tty_port_close_start() | tty->closing = 1 | tty_ldisc_flush() | | => IRQ | while (LSR & data ready) | uart_insert_char() | tty_flip_buffer_push() | <= EOI stop_rx() | . uart_shutdown() | . free xmit.buf | . tty_port_tty_set(NULL) | . tty->closing = 0 | . | flush_to_ldisc() | n_tty_receive_buf_common() | __receive_buf() | ... | commit_echoes() | uart_flush_chars() | __uart_start() | ** OOPS on port.tty deref ** tty_ldisc_flush() | Input processing must be prevented from echoing (tty->closing = 1) until _after_ the input buffers have been flushed again at the end of uart_close(). [1] In fact, some input may actually be buffered _after_ stop_rx() since the rx interrupt may have already triggered but not yet been handled when stop_rx() disables rx interrupts. Fixes: 2e758910832d ("serial: core: Flush ldisc after dropping port mutex in uart_close()") Reported-by: Robert Elliott <elliott@hp.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10Revert "serial: imx: initialized DMA w/o HW flow enabled"David Jander
commit 907eda32a36fcdb979bdb91ea097abb3dd2c23c9 upstream. This reverts commit 068500e08dc87ea9a453cc4a500cf3ab28d0f936. According to some tests, SDMA support is broken at least for i.MX6 without HW flow control. Different forms of data-corruption appear either with the ROM firmware for the SDMA controller as well as when loading Freescale provided SDMA firmware versions 1.1 or 3.1. Signed-off-by: David Jander <david@protonic.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10usb-storage: ignore ZTE MF 823 card reader in mode 0x1225Oliver Neukum
commit 5fb2c782f451a4fb9c19c076e2c442839faf0f76 upstream. This device automatically switches itself to another mode (0x1405) unless the specific access pattern of Windows is followed in its initial mode. That makes a dirty unmount of the internal storage devices inevitable if they are mounted. So the card reader of such a device should be ignored, lest an unclean removal become inevitable. This replaces an earlier patch that ignored all LUNs of this device. That patch was overly broad. Signed-off-by: Oliver Neukum <oneukum@suse.com> Reviewed-by: Lars Melin <larsm17@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10ata: pmp: add quirk for Marvell 4140 SATA PMPLior Amsalem
commit 945b47441d83d2392ac9f984e0267ad521f24268 upstream. This commit adds the necessary quirk to make the Marvell 4140 SATA PMP work properly. This PMP doesn't like SRST on port number 4 (the host port) so this commit marks this port as not supporting SRST. Signed-off-by: Lior Amsalem <alior@marvell.com> Reviewed-by: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10regulator: s2mps11: Fix GPIO suspend enable shift wrapping bugKrzysztof Kozlowski
commit 32c848e33ace75fce388cceff76223d12b46eaa3 upstream. Status of enabling suspend mode for regulator was stored in bitmap-like long integer. However since adding support for S2MPU02 the number of regulators exceeded 32 so on devices with more than 32 regulators (S2MPU02 and S2MPS13) overflow happens when shifting the bit. This could lead to enabling suspend mode for completely different regulator than intended or to switching different regulator to other mode (e.g. from always enabled to controlled by PWRHOLD pin). Both cases could result in larger energy usage and issues when suspending to RAM. Fixes: 00e2573d2c10 ("regulator: s2mps11: Add support S2MPU02 regulator device") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10Input: usbtouchscreen - avoid unresponsive TSC-30 touch screenBernhard Bender
commit 968491709e5b1aaf429428814fff3d932fa90b60 upstream. This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30 touch screen. Due to a missing delay between the RESET and SET_RATE commands, the touch screen may become unresponsive during system startup or driver loading. According to the DMC documentation, a delay is needed after the RESET command to allow the chip to complete its internal initialization. As this delay is not guaranteed, we had a system where the touch screen occasionally did not send any touch data. There was no other indication of the problem. The patch fixes the problem by adding a 150ms delay between the RESET and SET_RATE commands. Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com> Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10spi: imx: Fix small DMA transfersSascha Hauer
commit f6ee9b582d2db652497b73c1f117591dfb6d3a90 upstream. DMA transfers must be greater than the watermark level size. spi_imx->rx_wml and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct spi_transfer contains the transfer len in bytes. Fix the check if DMA is possible for a transfer accordingly. This fixes transfers with sizes between 33 and 128 bytes for which previously was claimed that DMA is possible. Fixes: f62caccd12c17e4 (spi: spi-imx: add DMA support) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10spi: img-spfi: fix support for speeds up to 1/4th input clockSifan Naeem
commit 6a806a214af42ac951e2d85e64d1bf4463482e16 upstream. Setting the Same Edge bit indicates to the spfi block to receive and transmit data on the same edge of the spfi clock, which in turn doubles the operating frequency of spfi. The maximum supported frequency is limited to 1/4th of the spfi input clock, but without this bit set the maximum would be 1/8th of the input clock. The current driver calculates the divisor with maximum speed at 1/4th of the input clock, this would fail if the requested frequency is higher than 1/8 of the input clock. Any requests for 1/8th of the input clock would still pass. Fixes: 8543d0e72d43 ("spi: img-spfi: Limit bit clock to 1/4th of input clock") Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10md/raid1: fix test for 'was read error from last working device'.NeilBrown
commit 34cab6f42003cb06f48f86a86652984dec338ae9 upstream. When we get a read error from the last working device, we don't try to repair it, and don't fail the device. We simple report a read error to the caller. However the current test for 'is this the last working device' is wrong. When there is only one fully working device, it assumes that a non-faulty device is that device. However a spare which is rebuilding would be non-faulty but so not the only working device. So change the test from "!Faulty" to "In_sync". If ->degraded says there is only one fully working device and this device is in_sync, this must be the one. This bug has existed since we allowed read_balance to read from a recovering spare in v3.0 Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com> Fixes: 76073054c95b ("md/raid1: clean up read_balance.") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10iwlwifi: pcie: prepare the device before accessing itEmmanuel Grumbach
commit f9e5554cd8ca1d1212ec922755b397a20f737923 upstream. For 8000 series, we need to access the device to know what firmware to load. Before we do so, we need to prepare the device otherwise we might not be able to access the hardware. Fixes: c278754a21e6 ("iwlwifi: mvm: support family 8000 B2/C steps") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10iwlwifi: nvm: remove mac address byte swapping in 8000 familyLiad Kaufman
commit be88a1ada9b97bb016196b7f4a1fc2fe2f798529 upstream. This fixes the byte order copying in the MAO (Mac Override Section) section from the PNVM, as the byte swapping is not required anymore in the 8000 family. Due to the byte swapping, the driver was reporting an incorrect MAC adddress. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10iwlwifi: mvm: fix antenna selection when BT is activeEmmanuel Grumbach
commit 923a8c1d8069104726bde55c37cec66324ccc328 upstream. When BT is active, we want to avoid the shared antenna for management frame to make sure we don't disturb BT. There was a bug in that code because it chose the antenna BIT(ANT_A) where ANT_A is already a bitmap (0x1). This means that the antenna chosen in the end was ANT_B. While this is not optimal on devices with 2 antennas (it'd disturb BT), it is critical on single antenna devices like 3160 which couldn't connect at all when BT was active. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=97181 Fixes: 34c8b24ff284 ("iwlwifi: mvm: BT Coex - avoid the shared antenna for management frames") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10HID: cp2112: fix to force single data-report replyAntonio Borneo
commit 6debce6f4e787a8eb4cec94e7afa85fb4f40db27 upstream. Current implementation of cp2112_raw_event() only accepts one data report at a time. If last received data report is not fully handled yet, a new incoming data report will overwrite it. In such case we don't guaranteed to propagate the correct incoming data. The trivial fix implemented here forces a single report at a time by requesting in cp2112_read() no more than 61 byte of data, which is the payload size of a single data report. Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: Ellen Wang <ellen@cumulusnetworks.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10mmc: sdhci-pxav3: fix platform_data is not initializedJingju Hou
commit 9cd76049f0d90ae241f5ad80e311489824527000 upstream. pdev->dev.platform_data is not initialized if match is true in function sdhci_pxav3_probe. Just local variable pdata is assigned the return value from function pxav3_get_mmc_pdata(). static int sdhci_pxav3_probe(struct platform_device *pdev) { struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; ... if (match) { ret = mmc_of_parse(host->mmc); if (ret) goto err_of_parse; sdhci_get_of_property(pdev); pdata = pxav3_get_mmc_pdata(dev); } ... } Signed-off-by: Jingju Hou <houjingj@marvell.com> Fixes: b650352dd3df("mmc: sdhci-pxa: Add device tree support") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10mmc: sdhci-esdhc: Make 8BIT bus workJoakim Tjernlund
commit 8e91125ff3f57f15c6568e2a6d32743b3f7815e4 upstream. Support for 8BIT bus with was added some time ago to sdhci-esdhc but then missed to remove the 8BIT from the reserved bit mask which made 8BIT non functional. Fixes: 66b50a00992d ("mmc: esdhc: Add support for 8-bit bus width and..") Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10mmc: sdhci check parameters before call dma_free_coherentPeng Fan
commit 7ac020366b0a436d726408841160b5dc32c19214 upstream. We should not call dma_free_coherent if host->adma_table is NULL, otherwise may trigger panic. Fixes: d1e49f77d7c7 ("mmc: sdhci: convert ADMA descriptors to a...") Signed-off-by: Peng Fan <van.freenix@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10mmc: omap_hsmmc: Fix DTO and DCRC handlingKishon Vijay Abraham I
commit 408806f740497c5d71f9c305b3d6aad260ff186d upstream. DTO/DCRC errors were not being informed to the mmc core since commit ae4bf788ee9b ("mmc: omap_hsmmc: consolidate error report handling of HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC errors. This is because after this commit 'host->data' is checked after it has been cleared to NULL by omap_hsmmc_dma_cleanup(). Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked making core layer not to be aware of DTO/DCRC errors. Because of this any command invoked after DTO/DCRC error leads to a hang. Fix this by checking for 'host->data' before it is actually cleared. Fixes: ae4bf788ee9b ("mmc: omap_hsmmc: consolidate error report handling of HSMMC IRQ") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10iommu/vt-d: Fix VM domain ID leakAlex Williamson
commit 46ebb7af7b93792de65e124e1ab8b89a108a41f2 upstream. This continues the attempt to fix commit fb170fb4c548 ("iommu/vt-d: Introduce helper functions to make code symmetric for readability"). The previous attempt in commit 71684406905f ("iommu/vt-d: Detach domain *only* from attached iommus") overlooked the fact that dmar_domain.iommu_bmp gets cleared for VM domains when devices are detached: intel_iommu_detach_device domain_remove_one_dev_info domain_detach_iommu The domain is detached from the iommu, but the iommu is still attached to the domain, for whatever reason. Thus when we get to domain_exit(), we can't rely on iommu_bmp for VM domains to find the active iommus, we must check them all. Without that, the corresponding bit in intel_iommu.domain_ids doesn't get cleared and repeated VM domain creation and destruction will run out of domain IDs. Meanwhile we still can't call iommu_detach_domain() on arbitrary non-VM domains or we risk clearing in-use domain IDs, as 71684406905f attempted to address. It's tempting to modify iommu_detach_domain() to test the domain iommu_bmp, but the call ordering from domain_remove_one_dev_info() prevents it being able to work as fb170fb4c548 seems to have intended. Caching of unused VM domains on the iommu object seems to be the root of the problem, but this code is far too fragile for that kind of rework to be proposed for stable, so we simply revert this chunk to its state prior to fb170fb4c548. Fixes: fb170fb4c548 ("iommu/vt-d: Introduce helper functions to make code symmetric for readability") Fixes: 71684406905f ("iommu/vt-d: Detach domain *only* from attached iommus") Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10Subject: pinctrl: imx1-core: Fix debug output in .pin_config_set callbackUwe Kleine-König
commit 9571b25df1dbf4db17191b54f59734e8b77fd591 upstream. imx1_pinconf_set assumes that the array of pins in struct imx1_pinctrl_soc_info can be indexed by pin id to get the pinctrl_pin_desc for a pin. This used to be correct up to commit 607af165c047 which removed some entries from the array and so made it wrong to access the array by pin id. The result of this bug is a wrong pin name in the output for small pin ids and an oops for the bigger ones. This patch is the result of a discussion that includes patches by Markus Pargmann and Chris Ruehl. Fixes: 607af165c047 ("pinctrl: i.MX27: Remove nonexistent pad definitions") Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10drivers: clk: st: Incorrect register offset used for lock_statusPankaj Dev
commit 56551da9255f20ffd3a9711728a1a3ad4b7100af upstream. Incorrect register offset used for sthi407 clockgenC Signed-off-by: Pankaj Dev <pankaj.dev@st.com> Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org> Fixes: 51306d56ba81 ("clk: st: STiH407: Support for clockgenC0") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10drivers: clk: st: Fix mux bit-setting for Cortex A9 clocksGabriel Fernandez
commit 3be6d8ce639d92e60d144fb99dd74a53fe3799bb upstream. This patch fixes the mux bit-setting for ClockgenA9. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org> Fixes: 13e6f2da1ddf ("clk: st: STiH407: Support for A9 MUX Clocks") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10drivers: clk: st: Fix flexgen lock initGiuseppe Cavallaro
commit 0f4f2afd4402883a51ad27a1d9e046643bb1e3cb upstream. While proving lock, the following warning happens and it is fixed after initializing lock in the setup function INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.27-02861-g39df285-dirty #33 [<c00154ac>] (unwind_backtrace+0x0/0xf4) from [<c0011b50>] (show_stack+0x10/0x14) [<c0011b50>] (show_stack+0x10/0x14) from [<c00689ac>] (__lock_acquire+0x900/0xb14) [<c00689ac>] (__lock_acquire+0x900/0xb14) from [<c0069394>] (lock_acquire+0x68/0x7c) [<c0069394>] (lock_acquire+0x68/0x7c) from [<c04958f8>] (_raw_spin_lock_irqsave+0x48/0x5c) [<c04958f8>] (_raw_spin_lock_irqsave+0x48/0x5c) from [<c0381e6c>] (clk_gate_endisable+0x28/0x88) [<c0381e6c>] (clk_gate_endisable+0x28/0x88) from [<c0381ee0>] (clk_gate_enable+0xc/0x14) [<c0381ee0>] (clk_gate_enable+0xc/0x14) from [<c0386c68>] (flexgen_enable+0x28/0x40) [<c0386c68>] (flexgen_enable+0x28/0x40) from [<c037f260>] (__clk_enable+0x5c/0x9c) [<c037f260>] (__clk_enable+0x5c/0x9c) from [<c037f558>] (clk_enable+0x18/0x2c) [<c037f558>] (clk_enable+0x18/0x2c) from [<c064a1dc>] (st_lpc_of_register+0xc0/0x248) [<c064a1dc>] (st_lpc_of_register+0xc0/0x248) from [<c0649e44>] (clocksource_of_init+0x34/0x58) [<c0649e44>] (clocksource_of_init+0x34/0x58) from [<c0637ddc>] (sti_timer_init+0x10/0x18) [<c0637ddc>] (sti_timer_init+0x10/0x18) from [<c06343f8>] (time_init+0x20/0x30) [<c06343f8>] (time_init+0x20/0x30) from [<c0632984>] (start_kernel+0x20c/0x2e8) [<c0632984>] (start_kernel+0x20c/0x2e8) from [<40008074>] (0x40008074) Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org> Fixes: b116517055b7 ("clk: st: STiH407: Support for Flexgen Clocks") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10st: null pointer dereference panic caused by use after kref_put by st_openSeymour, Shane M
commit e7ac6c6666bec0a354758a1298d3231e4a635362 upstream. Two SLES11 SP3 servers encountered similar crashes simultaneously following some kind of SAN/tape target issue: ... qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-8009:3: DEVICE RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: DEVICE RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8009:3: TARGET RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: TARGET RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8012:3: BUS RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-802b:3: BUS RESET SUCCEEDED nexus=3:0:2. qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8018:3: ADAPTER RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-00af:3: Performing ISP error recovery - ha=ffff88bf04d18000. rport-3:0-0: blocked FC remote port time out: removing target and saving binding qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8017:3: ADAPTER RESET SUCCEEDED nexus=3:0:2. rport-2:0-0: blocked FC remote port time out: removing target and saving binding sg_rq_end_io: device detached BUG: unable to handle kernel NULL pointer dereference at 00000000000002a8 IP: [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 PGD 7e6586f067 PUD 7e5af06067 PMD 0 [1739975.390354] Oops: 0002 [#1] SMP CPU 0 ... Supported: No, Proprietary modules are loaded [1739975.390463] Pid: 27965, comm: ABCD Tainted: PF X 3.0.101-0.29-default #1 HP ProLiant DL580 Gen8 RIP: 0010:[<ffffffff8133b268>] [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP: 0018:ffff8839dc1e7c68 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff883f0592fc00 RCX: 0000000000000090 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000138 RBP: 0000000000000138 R08: 0000000000000010 R09: ffffffff81bd39d0 R10: 00000000000009c0 R11: ffffffff81025790 R12: 0000000000000001 R13: ffff883022212b80 R14: 0000000000000004 R15: ffff883022212b80 FS: 00007f8e54560720(0000) GS:ffff88407f800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00000000000002a8 CR3: 0000007e6ced6000 CR4: 00000000001407f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process ABCD (pid: 27965, threadinfo ffff8839dc1e6000, task ffff883592e0c640) Stack: ffff883f0592fc00 00000000fffffffa 0000000000000001 ffff883022212b80 ffff883eff772400 ffffffffa03fa309 0000000000000000 0000000000000000 ffffffffa04003a0 ffff883f063196c0 ffff887f0379a930 ffffffff8115ea1e Call Trace: [<ffffffffa03fa309>] st_open+0x129/0x240 [st] [<ffffffff8115ea1e>] chrdev_open+0x13e/0x200 [<ffffffff811588a8>] __dentry_open+0x198/0x310 [<ffffffff81167d74>] do_last+0x1f4/0x800 [<ffffffff81168fe9>] path_openat+0xd9/0x420 [<ffffffff8116946c>] do_filp_open+0x4c/0xc0 [<ffffffff8115a00f>] do_sys_open+0x17f/0x250 [<ffffffff81468d92>] system_call_fastpath+0x16/0x1b [<00007f8e4f617fd0>] 0x7f8e4f617fcf Code: eb d3 90 48 83 ec 28 40 f6 c6 04 48 89 6c 24 08 4c 89 74 24 20 48 89 fd 48 89 1c 24 4c 89 64 24 10 41 89 f6 4c 89 6c 24 18 74 11 <f0> ff 8f 70 01 00 00 0f 94 c0 45 31 ed 84 c0 74 2b 4c 8d a5 a0 RIP [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP <ffff8839dc1e7c68> CR2: 00000000000002a8 Analysis reveals the cause of the crash to be due to STp->device being NULL. The pointer was NULLed via scsi_tape_put(STp) when it calls scsi_tape_release(). In st_open() we jump to err_out after scsi_block_when_processing_errors() completes and returns the device as offline (sdev_state was SDEV_DEL): 1180 /* Open the device. Needs to take the BKL only because of incrementing the SCSI host 1181 module count. */ 1182 static int st_open(struct inode *inode, struct file *filp) 1183 { 1184 int i, retval = (-EIO); 1185 int resumed = 0; 1186 struct scsi_tape *STp; 1187 struct st_partstat *STps; 1188 int dev = TAPE_NR(inode); 1189 char *name; ... 1217 if (scsi_autopm_get_device(STp->device) < 0) { 1218 retval = -EIO; 1219 goto err_out; 1220 } 1221 resumed = 1; 1222 if (!scsi_block_when_processing_errors(STp->device)) { 1223 retval = (-ENXIO); 1224 goto err_out; 1225 } ... 1264 err_out: 1265 normalize_buffer(STp->buffer); 1266 spin_lock(&st_use_lock); 1267 STp->in_use = 0; 1268 spin_unlock(&st_use_lock); 1269 scsi_tape_put(STp); <-- STp->device = 0 after this 1270 if (resumed) 1271 scsi_autopm_put_device(STp->device); 1272 return retval; The ref count for the struct scsi_tape had already been reduced to 1 when the .remove method of the st module had been called. The kref_put() in scsi_tape_put() caused scsi_tape_release() to be called: 0266 static void scsi_tape_put(struct scsi_tape *STp) 0267 { 0268 struct scsi_device *sdev = STp->device; 0269 0270 mutex_lock(&st_ref_mutex); 0271 kref_put(&STp->kref, scsi_tape_release); <-- calls this 0272 scsi_device_put(sdev); 0273 mutex_unlock(&st_ref_mutex); 0274 } In scsi_tape_release() the struct scsi_device in the struct scsi_tape gets set to NULL: 4273 static void scsi_tape_release(struct kref *kref) 4274 { 4275 struct scsi_tape *tpnt = to_scsi_tape(kref); 4276 struct gendisk *disk = tpnt->disk; 4277 4278 tpnt->device = NULL; <<<---- where the dev is nulled 4279 4280 if (tpnt->buffer) { 4281 normalize_buffer(tpnt->buffer); 4282 kfree(tpnt->buffer->reserved_pages); 4283 kfree(tpnt->buffer); 4284 } 4285 4286 disk->private_data = NULL; 4287 put_disk(disk); 4288 kfree(tpnt); 4289 return; 4290 } Although the problem was reported on SLES11.3 the problem appears in linux-next as well. The crash is fixed by reordering the code so we no longer access the struct scsi_tape after the kref_put() is done on it in st_open(). Signed-off-by: Shane Seymour <shane.seymour@hp.com> Signed-off-by: Darren Lavender <darren.lavender@hp.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com> Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10scsi: fix memory leak with scsi-mqTony Battersby
commit 0c958ecc69c277b25f38f72bc6d18ab145e8167c upstream. Fix a memory leak with scsi-mq triggered by commands with large data transfer length. __sg_alloc_table() sets both table->nents and table->orig_nents to the same value. When the scatterlist is DMA-mapped, table->nents is overwritten with the (possibly smaller) size of the DMA-mapped scatterlist, while table->orig_nents retains the original size of the allocated scatterlist. scsi_free_sgtable() should therefore check orig_nents instead of nents, and all code that initializes sdb->table without calling __sg_alloc_table() should set both nents and orig_nents. Fixes: d285203cf647 ("scsi: add support for a blk-mq based I/O path.") Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-10scsi: fix host max depth checking for the 'queue_depth' sysfs interfaceJens Axboe
commit 1278dd6809b11dc298e19d81ac0916275f7318c1 upstream. Commit 1e6f2416044c0 changed the scsi sysfs 'queue_depth' code to rejects depths higher than the scsi host template setting. But lots of hosts set this to 1, and update the settings in the scsi host when the controller/devices probing happens. This breaks (at least) mpt2sas and mpt3sas runtime setting of queue depth, returning EINVAL for all settings but '1'. And once it's set to 1, there's no way to go back up. Fixes: 1e6f2416044c0 "scsi: don't allow setting of queue_depth bigger than can_queue" Signed-off-by: Jens Axboe <axboe@fb.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2026-03-04 03:58:00 +0000