| Age | Commit message (Collapse) | Author |
|---|
|
commit bafb2f7d4755bf1571bd5e9a03b97f3fc4fe69ae upstream.
There is a disparity in the context image saved to disk and our own
bookkeeping - that is we presume the RING_HEAD and RING_TAIL match our
stored ce->ring->tail value. However, as we emit WA_TAIL_DWORDS into the
ring but may not tell the GPU about them, the GPU may be lagging behind
our bookkeeping. Upon hibernation we do not save stolen pages, presuming
that their contents are volatile. This means that although we start
writing into the ring at tail, the GPU starts executing from its HEAD
and there may be some garbage in between and so the GPU promptly hangs
upon resume.
Testcase: igt/gem_exec_suspend/basic-S4
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96526
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160921135108.29574-3-chris@chris-wilson.co.uk
Cc: Eric Blau <eblau1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b414fa01c31318383ae29d9d23cb9ca4184bbd86 upstream.
The current QP FetchBurstMax value is 256B, which
is incorrect since a WR can exceed that value. The
result being a partial WR fetched by hardware, and
a fatal "bad WR" error posted by the SGE.
So bump the FetchBurstMax to 512B.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 828f84ee8f84710ea1818b3565add268bcb824c8 upstream.
FIFO was being read every sample after the "almost full" state was
reached. This was due to an incorrect placement of the parenthesis
in the while condition check.
Note - the fixes tag is not actually correct, but the fix in this patch
would also be needed for it to function correctly so we'll go with that
one. Backports should pick up both.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Fixes: b74fccad7 ("iio: health: max30100: correct FIFO check condition")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c113b5e0082e90d2e1c7b12e96a7b8cf0623e27 upstream.
The DHT22 (AM2302) datasheet specifies that the LOW start pulse should not
exceed 20ms. However, observations with an oscilloscope of an RPi Model 2B
(rev 1.1) communicating with a DHT22 sensor showed that the driver was
consistently sending start pulses longer than 20ms:
Kernel 4.7.10-v7+ (n=132):
Minimum pulse length: 20.20ms
Maximum: 29.84ms
Mean: 24.96ms
StDev: 2.82ms
Sensor response rate: 100%
Read success rate: 76%
On kernel 4.8, the start pulse was so long that the sensor would not even
respond 97% of the time:
Kernel 4.8.16-v7+ (n=100):
Minimum pulse length: 30.4ms
Maximum: 74.4ms
Mean: 39.3ms
StDev: 10.2ms
Sensor response rate: 3%
Read success rate: 3%
The driver would return ETIMEDOUT and write log messages like this:
[ 51.430987] dht11 dht11@0: Only 1 signal edges detected
[ 66.311019] dht11 dht11@0: Only 0 signal edges detected
Replacing msleep(18) with usleep_range(18000, 20000) made the pulse length
sane again and restored responsiveness:
Kernel 4.8.16-v7+ with usleep_range (n=123):
Minimum pulse length: 18.16ms
Maximum: 20.20ms
Mean: 19.85ms
StDev: 0.51ms
Sensor response rate: 100%
Read success rate: 84%
Signed-off-by: John Brooks <john@fastquake.com>
Reviewed-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5badd1e97e6caeca78ad74191f12fc923c403a8 upstream.
The suspend/resume functions were using dev_to_iio_dev() to get
the iio_dev. That only works on IIO dev's. Replace it with spi
functions to get the correct iio_dev.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 802ecfc113df1e15af1d028427cbbe785ae9cc4a upstream.
The suspend/resume functions were using dev_to_iio_dev() to get
the iio_dev. That only works on IIO dev's. Replace it with i2c
functions to get the correct iio_dev.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d1aaf20ee655888c227d5137b7a63551f8d15416 upstream.
The suspend/resume functions were using dev_to_iio_dev() to get
the iio_dev. That only works on IIO dev's. Use dev_get_drvdata()
for a platform device to get the correct iio_dev.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b17c1bba9cec1727451b906d9a0c209774624873 upstream.
When tearingdown timesync, and not in arche platform, the state platform
callback is not initialized. That will trigger the following NULL
dereferencing.
CallTrace:
? gb_timesync_platform_unlock_bus+0x11/0x20 [greybus]
gb_timesync_teardown+0x85/0xc0 [greybus]
gb_timesync_svc_remove+0xab/0x190 [greybus]
gb_svc_del+0x29/0x110 [greybus]
gb_hd_del+0x14/0x20 [greybus]
ap_disconnect+0x24/0x60 [gb_es2]
usb_unbind_interface+0x7a/0x2c0
__device_release_driver+0x96/0x150
device_release_driver+0x1e/0x30
bus_remove_device+0xe7/0x130
device_del+0x116/0x230
usb_disable_device+0x97/0x1f0
usb_disconnect+0x80/0x260
hub_event+0x5ca/0x10e0
process_one_work+0x126/0x3b0
worker_thread+0x55/0x4c0
? process_one_work+0x3b0/0x3b0
kthread+0xc4/0xe0
? kthread_park+0xb0/0xb0
ret_from_fork+0x22/0x30
So, fix that by adding checks before use the callback.
Fixes: 970dc85bd95d ("greybus: timesync: Add timesync core driver")
Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d03a2fd2292e71936c4235885c35ccc3c94695b upstream.
Yet another laptop vendor rebranded Novatel E371.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83e526f2a2fa4b2e82b6bd3ddbb26b70acfa8947 upstream.
OS descriptor head, when flagged as provided, is accessed without
checking if it fits in provided buffer. Verify length before access.
Also, there are other places where buffer length it checked
after accessing offsets which are potentially past the end. Check
buffer length before as well to fail cleanly.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 407788b51db6f6aab499d02420082f436abf3238 upstream.
Commit 467d5c980709 ("usb: musb: Implement session bit based runtime PM for
musb-core") started implementing musb generic runtime PM support by
introducing devctl register session bit based state control.
This caused a regression where if a USB mass storage device is connected
to a USB hub, we can get:
usb 1-1: reset high-speed USB device number 2 using musb-hdrc
usb 1-1: device descriptor read/64, error -71
usb 1-1.1: new high-speed USB device number 4 using musb-hdrc
This is because before the USB storage device is connected, musb is
in OTG_STATE_A_SUSPEND. And we currently only set need_finish_resume
in musb_stage0_irq() and the related code calling finish_resume_work
in musb_resume() and musb_runtime_resume() never gets called.
To fix the issue, we can call schedule_delayed_work() directly in
musb_stage0_irq() to have finish_resume_work run.
And we should no longer never get interrupts when when suspended.
We have changed musb to no longer need pm_runtime_irqsafe().
The need_finish_resume flag was added in commit 9298b4aad37e ("usb:
musb: fix device hotplug behind hub") and no longer applies as far
as I can tell. So let's just remove the earlier code that no longer
is needed.
Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core")
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9b2997e4a0a874e452df7cdd7de5a54502bd0aa upstream.
Add a quirk for WORLDE easykey.25 MIDI keyboard (idVendor=0218,
idProduct=0401). The device reports that it has config string
descriptor at index 3, but when the system selects the configuration
and tries to get the description, it returns a -EPROTO error,
the communication restarts and this keeps repeating over and over again.
Not requesting the string descriptor makes the device work correctly.
Relevant info from Wireshark:
[...]
CONFIGURATION DESCRIPTOR
bLength: 9
bDescriptorType: 0x02 (CONFIGURATION)
wTotalLength: 101
bNumInterfaces: 2
bConfigurationValue: 1
iConfiguration: 3
Configuration bmAttributes: 0xc0 SELF-POWERED NO REMOTE-WAKEUP
1... .... = Must be 1: Must be 1 for USB 1.1 and higher
.1.. .... = Self-Powered: This device is SELF-POWERED
..0. .... = Remote Wakeup: This device does NOT support remote wakeup
bMaxPower: 50 (100mA)
[...]
45 0.369104 host 2.38.0 USB 64 GET DESCRIPTOR Request STRING
[...]
URB setup
bmRequestType: 0x80
1... .... = Direction: Device-to-host
.00. .... = Type: Standard (0x00)
...0 0000 = Recipient: Device (0x00)
bRequest: GET DESCRIPTOR (6)
Descriptor Index: 0x03
bDescriptorType: 0x03
Language Id: English (United States) (0x0409)
wLength: 255
46 0.369255 2.38.0 host USB 64 GET DESCRIPTOR Response STRING[Malformed Packet]
[...]
Frame 46: 64 bytes on wire (512 bits), 64 bytes captured (512 bits) on interface 0
USB URB
[Source: 2.38.0]
[Destination: host]
URB id: 0xffff88021f62d480
URB type: URB_COMPLETE ('C')
URB transfer type: URB_CONTROL (0x02)
Endpoint: 0x80, Direction: IN
Device: 38
URB bus id: 2
Device setup request: not relevant ('-')
Data: present (0)
URB sec: 1484896277
URB usec: 455031
URB status: Protocol error (-EPROTO) (-71)
URB length [bytes]: 0
Data length [bytes]: 0
[Request in: 45]
[Time from request: 0.000151000 seconds]
Unused Setup Header
Interval: 0
Start frame: 0
Copy of Transfer Flags: 0x00000200
Number of ISO descriptors: 0
[Malformed Packet: USB]
[Expert Info (Error/Malformed): Malformed Packet (Exception occurred)]
[Malformed Packet (Exception occurred)]
[Severity level: Error]
[Group: Malformed]
Signed-off-by: Lukáš Lalinský <lukas@oxygene.sk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d07830db1bdb254e4b50d366010b219286b8c937 upstream.
Seems that ATEN serial-to-usb devices using pl2303 exist with
different device ids. This patch adds a missing device ID so it
is recognised by the driver.
Signed-off-by: Marcel J.E. Mol <marcel@mesa.nl>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24d615a694d649aa2e167c3f97f62bdad07e3f84 upstream.
The Dell DW5570 is a re-branded Sierra Wireless MC8805 which will by
default boot with vid 0x413c and pid 0x81a3. When triggered QDL download
mode, the device switches to pid 0x81a6 and provides the standard TTY
used for firmware upgrade.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 362f4562466c3b9490e733e06999025638310d4a upstream.
Commit fdea2d09b997 ("dmaengine: cppi41: Add basic PM runtime support")
together with recent MUSB changes allowed USB and DMA on BeagleBone to idle
when no cable is connected. But looks like few corner case issues still
remain.
Looks like just by re-plugging USB cable about ten or so times on BeagleBone
when configured in USB peripheral mode we can get warnings and eventually
trigger an oops in cppi41 DMA:
WARNING: CPU: 0 PID: 14 at drivers/dma/cppi41.c:1154 cppi41_runtime_suspend+
x28/0x38 [cppi41]
...
WARNING: CPU: 0 PID: 14 at drivers/dma/cppi41.c:452
push_desc_queue+0x94/0x9c [cppi41]
...
Unable to handle kernel NULL pointer dereference at virtual
address 00000104
pgd = c0004000
[00000104] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
...
[<bf0d92cc>] (cppi41_runtime_resume [cppi41]) from [<c0589838>]
(__rpm_callback+0xc0/0x214)
[<c0589838>] (__rpm_callback) from [<c05899ac>] (rpm_callback+0x20/0x80)
[<c05899ac>] (rpm_callback) from [<c0589460>] (rpm_resume+0x504/0x78c)
[<c0589460>] (rpm_resume) from [<c058a1a0>] (pm_runtime_work+0x60/0xa8)
[<c058a1a0>] (pm_runtime_work) from [<c0156120>] (process_one_work+0x2b4/0x808)
This is because of a race with runtime PM and cppi41_dma_issue_pending()
as reported by Alexandre Bailon <abailon@baylibre.com> in earlier
set of patches. Based on mailing list discussions we however came to the
conclusion that a different fix from Alexandre's fix is needed in order
to guarantee that DMA is really active when we try to use it.
To fix the issue, we need to add a driver specific flag as we otherwise
can have -EINPROGRESS state set by runtime PM and can't rely on
pm_runtime_active() to tell us when we can use the DMA.
And we need to make sure the DMA transfers get triggered in the queued
order. So let's always queue the transfers, then flush the queue
from both cppi41_dma_issue_pending() and cppi41_runtime_resume()
as suggested by Grygorii Strashko <grygorii.strashko@ti.com> in an
earlier example patch.
For reference, this is also documented in Documentation/power/runtime_pm.txt
in the example at the end of the file as pointed out by Grygorii Strashko
<grygorii.strashko@ti.com>.
Based on earlier patches from Alexandre Bailon <abailon@baylibre.com>
and Grygorii Strashko <grygorii.strashko@ti.com> modified based on
testing and what was discussed on the mailing lists.
Fixes: fdea2d09b997 ("dmaengine: cppi41: Add basic PM runtime support")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bin Liu <b-liu@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae4a3e028bb8b59e7cfeb0cc9ef03d885182ce8b upstream.
Commit fdea2d09b997 ("dmaengine: cppi41: Add basic PM runtime support")
added runtime PM support for cppi41, but had corner case issues. Some of
the issues were fixed with commit 098de42ad670 ("dmaengine: cppi41: Fix
unpaired pm runtime when only a USB hub is connected"). That fix however
caused a new regression where we can get error -115 messages with USB on
BeagleBone when connecting a USB mass storage device to a hub.
This is because when connecting a USB mass storage device to a hub, the
initial DMA transfers can take over 200ms to complete and cppi41
autosuspend delay times out.
To fix the issue, we want to implement refcounting for chan_busy array
that contains the active dma transfers. Increasing the autosuspend delay
won't help as that the delay could be potentially seconds, and it's best
to let the USB subsystem to deal with the timeouts on errors.
The earlier attempt for runtime PM was buggy as the pm_runtime_get/put()
calls could get unpaired easily as they did not follow the state of
the chan_busy array as described in commit 098de42ad670 ("dmaengine:
cppi41: Fix unpaired pm runtime when only a USB hub is connected".
Let's fix the issue by adding pm_runtime_get() to where a new transfer
is added to the chan_busy array, and calls to pm_runtime_put() where
chan_busy array entry is cleared. This prevents any autosuspend timeouts
from happening while dma transfers are active.
Fixes: 098de42ad670 ("dmaengine: cppi41: Fix unpaired pm runtime when
only a USB hub is connected")
Fixes: fdea2d09b997 ("dmaengine: cppi41: Add basic PM runtime support")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bin Liu <b-liu@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 282e4637bc1c0b338708bcebd09d31c69abec070 upstream.
Commit 025bcc1 performed cleanup work on the 'wacom_pl_irq' function, making
it follow the standards used in the rest of the codebase. The change
unintiontionally allowed the function to send input events from reports
that are not marked as being in prox. This can cause problems as the
report values for X, Y, etc. are not guaranteed to be correct. In
particular, occasionally the tablet will send a report with these values
set to zero. If such a report is received it can caus an unexpected jump
in the XY position.
This patch surrounds more of the processing code with a proximity check,
preventing these zeroed reports from overwriting the current state. To
be safe, only the tool type and ABS_MISC events should be reported when
the pen is marked as being out of prox.
Fixes: 025bcc1540 ("HID: wacom: Simplify 'wacom_pl_irq'")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 877a021e08ccb6434718c0cc781fdf943c884cc0 upstream.
With NOGET quirk Logitech F510 is now fully workable in dinput mode including
rumble effects (according to fftest).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117091
[jkosina@suse.cz: fix patch format]
Signed-off-by: Ardinartsev Nikita <ardinar23@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed9ab4287f96e66340e0390e2c583f2f9110cba0 upstream.
Quirking the following AMI USB device with ALWAYS_POLL fixes an AMI
virtual keyboard and mouse from not responding and timing out when
it is attached to a ppc64el Power 8 system and when we have some
rapid open/closes on the mouse device.
usb 1-3: new high-speed USB device number 2 using xhci_hcd
usb 1-3: New USB device found, idVendor=046b, idProduct=ff01
usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-3: Product: Virtual Hub
usb 1-3: Manufacturer: American Megatrends Inc.
usb 1-3: SerialNumber: serial
usb 1-3.3: new high-speed USB device number 3 using xhci_hcd
usb 1-3.3: New USB device found, idVendor=046b, idProduct=ff31
usb 1-3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-3.3: Product: Virtual HardDisk Device
usb 1-3.3: Manufacturer: American Megatrends Inc.
usb 1-3.4: new low-speed USB device number 4 using xhci_hcd
usb 1-3.4: New USB device found, idVendor=046b, idProduct=ff10
usb 1-3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-3.4: Product: Virtual Keyboard and Mouse
usb 1-3.4: Manufacturer: American Megatrends Inc.
With the quirk I have not been able to trigger the issue with
half an hour of saturation soak testing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03c902bff524e0cf664737a33f2365f7837040bf upstream.
When the firmware restarts in a situation in which any station
has no queue reserved anymore because that queue was used, the
code will crash trying to access the queue_info array at the
offset 255, which is far too big. Fix this by checking that a
queue is actually reserved before writing its status.
Fixes: 8d98ae6eb0d5 ("iwlwifi: mvm: re-assign old queues after hw restart in dqa mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7941c59e45f3b6d30e07375e9b6713427e0a9f98 upstream.
Mistakenly, the driver is trying to load the 8000C firmware with an
incorrect name (i.e. with two hyphens where there should be only one)
and that fails. Fix that by removing the hyphen from the format
macro.
Fixes: e1ba684f762b ("iwlwifi: 8000: fix MODULE_FIRMWARE input")
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19b26d92dfb70f56440c187a20c49102ab648b97 upstream.
Not every pin can be configured. Add missed check to prevent access
violation.
Fixes: 4e80c8f50574 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b89970d81bbd52720fc64a3fe9572ee33588363 upstream.
Debounce value is set globally per community. Otherwise user will easily
get a kernel crash when they start using the feature:
BUG: unable to handle kernel paging request at ffffc900003be000
IP: byt_gpio_dbg_show+0xa9/0x430
Make it clear in byt_gpio_reg().
Note that this fix just prevents kernel to crash, but doesn't make any
difference to the existing logic. It means the last caller will win the
trade and debounce value will be configured accordingly. The actual
logic fix needs to be thought about and it's not as important as crash
fix. That's why the latter goes separately and right now.
Fixes: 658b476c742f ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0d5415b489f68b58e1983a53793d25d53098ed4b upstream.
This reverts commit c7070619f3408d9a0dffbed9149e6f00479cf43b.
This has been shown to regress on some ARM systems:
by forcing on DMA API usage for ARM systems, we have inadvertently
kicked open a hornets' nest in terms of cache-coherency. Namely that
unless the virtio device is explicitly described as capable of coherent
DMA by firmware, the DMA APIs on ARM and other DT-based platforms will
assume it is non-coherent. This turns out to cause a big problem for the
likes of QEMU and kvmtool, which generate virtio-mmio devices in their
guest DTs but neglect to add the often-overlooked "dma-coherent"
property; as a result, we end up with the guest making non-cacheable
accesses to the vring, the host doing so cacheably, both talking past
each other and things going horribly wrong.
We are working on a safer work-around.
Fixes: c7070619f340 ("vring: Force use of DMA API for ARM-based systems with legacy devices")
Reported-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7195439d1d71bc4a6c33cfb57bc669a7cd041041 upstream.
This reverts commit 4c81acab3816 ("bcma: init serial console directly
from ChipCommon code") as it broke IRQ assignment. Getting IRQ with
bcma_core_irq helper on SoC requires MIPS core to be set. It happens
*after* ChipCommon initialization so we can't do this so early.
This fixes a user reported regression. It wasn't critical as serial was
still somehow working but lack of IRQs was making in unreliable.
Fixes: 4c81acab3816 ("bcma: init serial console directly from ChipCommon code")
Reported-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0e287a401d9acf67b75180b26e2d62b7d482652 upstream.
A typo or copy-paste bug means that the register access intended for
regulator dcdce goes to dcdcb instead. This patch corrects it.
Fixes: 2ca342d391e3 (regulator: axp20x: Support AXP806 variant)
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cda8bba0f99d25d2061c531113c14fa41effc3ae upstream.
Currently, under certain circumstances vhost_init_is_le does just a part
of the initialization job, and depends on vhost_reset_is_le being called
too. For this reason vhost_vq_init_access used to call vhost_reset_is_le
when vq->private_data is NULL. This is not only counter intuitive, but
also real a problem because it breaks vhost_net. The bug was introduced to
vhost_net with commit 2751c9882b94 ("vhost: cross-endian support for
legacy devices"). The symptom is corruption of the vq's used.idx field
(virtio) after VHOST_NET_SET_BACKEND was issued as a part of the vhost
shutdown on a vq with pending descriptors.
Let us make sure the outcome of vhost_init_is_le never depend on the state
it is actually supposed to initialize, and fix virtio_net by removing the
reset from vhost_vq_init_access.
With the above, there is no reason for vhost_reset_is_le to do just half
of the job. Let us make vhost_reset_is_le reinitialize is_le.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reported-by: Michael A. Tebolt <miket@us.ibm.com>
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixes: commit 2751c9882b94 ("vhost: cross-endian support for legacy devices")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Michael A. Tebolt <miket@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 161e6d44a5e2d3f85365cb717d60e363171b39e6 upstream.
One of our kernelCI boxes hanged at boot because a faulty eSDHC device
was triggering spurious CARD_INT interrupts for SD cards, causing CMD52
reads, which are not allowed for SD devices. This adds a sanity check
to the interruption path, preventing that illegal command from getting
sent if the CARD_INT interruption should be disabled.
This quirk allows that particular machine to resume boot despite the
faulty hardware, instead of getting hung dealing with thousands of
mishandled interrupts.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a96dfddbcc04336bbed50dc2b24823e45e09e80c upstream.
Reading a sysfs "memoryN/valid_zones" file leads to the following oops
when the first page of a range is not backed by struct page.
show_valid_zones() assumes that 'start_pfn' is always valid for
page_zone().
BUG: unable to handle kernel paging request at ffffea017a000000
IP: show_valid_zones+0x6f/0x160
This issue may happen on x86-64 systems with 64GiB or more memory since
their memory block size is bumped up to 2GiB. [1] An example of such
systems is desribed below. 0x3240000000 is only aligned by 1GiB and
this memory block starts from 0x3200000000, which is not backed by
struct page.
BIOS-e820: [mem 0x0000003240000000-0x000000603fffffff] usable
Since test_pages_in_a_zone() already checks holes, fix this issue by
extending this function to return 'valid_start' and 'valid_end' for a
given range. show_valid_zones() then proceeds with the valid range.
[1] 'Commit bdee237c0343 ("x86: mm: Use 2GB memory block size on
large-memory x86-64 systems")'
Link: http://lkml.kernel.org/r/20170127222149.30893-3-toshi.kani@hpe.com
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Zhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Reza Arbab <arbab@linux.vnet.ibm.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 2dae99558e86894e9e5dbf097477baaa5eb70134 upstream.
For an ATA device supporting the sense data reporting feature set, a
failed command will trigger the execution of ata_eh_request_sense if
the result task file of the failed command has the ATA_SENSE bit set
(sense data available bit). ata_eh_request_sense executes the REQUEST
SENSE DATA EXT command to retrieve the sense data of the failed
command. On success of REQUEST SENSE DATA EXT, the ATA_SENSE bit will
NOT be set (the command succeeded) but ata_eh_request_sense
nevertheless tests the availability of sense data by testing that bit
presence in the result tf of the REQUEST SENSE DATA EXT command. This
leads us to falsely assume that request sense data failed and to the
warning message:
atax.xx: request sense failed stat 50 emask 0
Upon success of REQUEST SENSE DATA EXT, set the ATA_SENSE bit in the
result task file command so that sense data can be returned by
ata_eh_request_sense.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e0edc8c546463f268d41d064d855bcff994c52fa upstream.
Marko reports that CX1-JB512-HP shows the same timeout issues as
CX1-JB256-HP. Let's apply MAX_SEC_128 to all devices in the series.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marko Koski-Vähälä <marko@koski-vahala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 064c3db9c564cc5be514ac21fb4aa26cc33db746 upstream.
Here, If devm_ioremap will fail. It will return NULL.
Then hpriv->base = NULL - 0x20000; Kernel can run into
a NULL-pointer dereference. This error check will avoid
NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24bf7ae359b8cca165bb30742d2b1c03a1eb23af upstream.
Based on the xf86-video-nv code, NFORCE (NV1A) and NFORCE2 (NV1F) have a
different way of retrieving clocks. See the
nv_hw.c:nForceUpdateArbitrationSettings function in the original code
for how these clocks were accessed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54587
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d347583a39e2df609a9e40c835f72d3614665b53 upstream.
Store the ELD correctly, not just enough copies of the first byte
to pad out the given ELD size.
Signed-off-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
Fixes: 120b0c39c756 ("drm/nv50-/disp: audit and version SOR_HDA_ELD method")
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 57bcd0a6364cd4eaa362d7ff1777e88ddf501602 upstream.
Missing check for crtcs present.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=193341
https://bugs.freedesktop.org/show_bug.cgi?id=99387
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cdca06e4e85974d8a3503ab15709dbbaf90d3dd1 upstream.
According to VLI64 Intel Atom E3800 Specification Update (#329901)
concurrent read accesses may result in returning 0xffffffff and write
accesses may be dropped silently.
To workaround all accesses must be protected by locks.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e9faa15469ed7c7467423db4c62aeed3ff4cae3 upstream.
In case of a zero-length report, the gpio direction_input callback would
currently return success instead of an errno.
Fixes: 1ffb3c40ffb5 ("HID: cp2112: make transfer buffers DMA capable")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a7b5df84b6b4e5d599c7289526eed96541a0654 upstream.
A recent commit fixing DMA-buffers on stack added a shared transfer
buffer protected by a spinlock. This is broken as the USB HID request
callbacks can sleep. Fix this up by replacing the spinlock with a mutex.
Fixes: 1ffb3c40ffb5 ("HID: cp2112: make transfer buffers DMA capable")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c8f325a59cfc718d13a50fbc746ed9b415c25e92 upstream.
Some AArch64 UEFI implementations disable the MMU in ExitBootServices(),
after which unaligned accesses to RAM are no longer supported.
Commit:
abfb7b686a3e ("efi/libstub/arm*: Pass latest memory map to the kernel")
fixed an issue in the memory map handling of the stub FDT code, but
inadvertently created an issue with such firmware, by moving some
of the FDT manipulation to after the invocation of ExitBootServices().
Given that the stub's libfdt implementation uses the ordinary, accelerated
string functions, which rely on hardware handling of unaligned accesses,
manipulating the FDT with the MMU off may result in alignment faults.
So fix the situation by moving the update_fdt_memmap() call into the
callback function invoked by efi_exit_boot_services() right before it
calls the ExitBootServices() UEFI service (which is arguably a better
place for it anyway)
Note that disabling the MMU in ExitBootServices() is not compliant with
the UEFI spec, and carries great risk due to the fact that switching from
cached to uncached memory accesses halfway through compiler generated code
(i.e., involving a stack) can never be done in a way that is architecturally
safe.
Fixes: abfb7b686a3e ("efi/libstub/arm*: Pass latest memory map to the kernel")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Cc: mark.rutland@arm.com
Cc: linux-efi@vger.kernel.org
Cc: matt@codeblueprint.co.uk
Cc: leif.lindholm@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1485971102-23330-2-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 030305d69fc6963c16003f50d7e8d74b02d0a143 upstream.
In a struct pcie_link_state, link->root points to the pcie_link_state of
the root of the PCIe hierarchy. For the topmost link, this points to
itself (link->root = link). For others, we copy the pointer from the
parent (link->root = link->parent->root).
Previously we recognized that Root Ports originated PCIe hierarchies, but
we treated PCI/PCI-X to PCIe Bridges as being in the middle of the
hierarchy, and when we tried to copy the pointer from link->parent->root,
there was no parent, and we dereferenced a NULL pointer:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000090
IP: [<ffffffff9e424350>] pcie_aspm_init_link_state+0x170/0x820
Recognize that PCI/PCI-X to PCIe Bridges originate PCIe hierarchies just
like Root Ports do, so link->root for these devices should also point to
itself.
Fixes: 51ebfc92b72b ("PCI: Enumerate switches below PCI-to-PCIe bridges")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=193411
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1022181
Tested-by: lists@ssl-mail.com
Tested-by: Jayachandran C. <jnair@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5b9f57516337b523f7466a53939aaaea7b78141b ]
Another rebranded Novatel E371. qmi_wwan should drive this device, while
cdc_ether should ignore it. Even though the USB descriptors are plain
CDC-ETHER that USB interface is a QMI interface. Ref commit 7fdb7846c9ca
("qmi_wwan/cdc_ether: add device IDs for Dell 5804 (Novatel E371) WWAN
card")
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6a0b76c04ec157c88ca943debf78a8ee58469f2d ]
Runtime suspend shouldn't be executed if the tx queue is not empty,
because the device is not idle.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e048fc50d7bde23136e098e04a324d7e3404408d ]
A driver using dev_alloc_page() must not reuse a page allocated from
emergency memory reserve.
Otherwise all packets using this page will be immediately dropped,
unless for very specific sockets having SOCK_MEMALLOC bit set.
This issue might be hard to debug, because only a fraction of received
packets would be dropped.
Fixes: 4415a0319f92 ("net/mlx5e: Implement RX mapped page cache for page recycle")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cd33b3e0da43522ff8e8f2b2b71d3d08298512b0 ]
Commit a1cba5613edf ("net: phy: Add Broadcom phy library for common
interfaces") make the BCM63xx PHY driver utilize bcm_phy_config_intr()
which would appear to do the right thing, except that it does not write
to the MII_BCM63XX_IR register but to MII_BCM54XX_ECR which is
different.
This would be causing invalid link parameters and events from being
generated by the PHY interrupt.
Fixes: a1cba5613edf ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d5ff72d9af73bc3cbaa3edb541333a851f8c7295 ]
vxlan->cfg.dst_port is in network byte order, so an htons()
is needed here. Also reduced comment length to stay closer
to 80 column width (still slightly over, however).
Fixes: e1e5314de08b ("vxlan: implement GPE")
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6391a4481ba0796805d6581e42f9f0418c099e34 ]
Commit 501db511397f ("virtio: don't set VIRTIO_NET_HDR_F_DATA_VALID on
xmit") in fact disables VIRTIO_HDR_F_DATA_VALID on receiving path too,
fixing this by adding a hint (has_data_valid) and set it only on the
receiving path.
Cc: Rolf Neugebauer <rolf.neugebauer@docker.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8ec3e8a192ba6f13be4522ee81227c792c86fb1a ]
Due to alignment requirements of the hardware transmissions are split into
two DMA descriptors, a small padding descriptor of 0 - 3 bytes in length
followed by a descriptor for rest of the packet.
In the case of IP packets the first descriptor will never be zero due to
the way that the stack aligns buffers for IP packets. However, for non-IP
packets it may be zero.
In that case it has been reported that timeouts occur, presumably because
transmission stops at the first zero-length DMA descriptor and thus the
packet is not transmitted. However, in my environment a BUG is triggered as
follows:
[ 20.381417] ------------[ cut here ]------------
[ 20.386054] kernel BUG at lib/swiotlb.c:495!
[ 20.390324] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 20.395805] Modules linked in:
[ 20.398862] CPU: 0 PID: 2089 Comm: mz Not tainted 4.10.0-rc3-00001-gf13ad2db193f #162
[ 20.406689] Hardware name: Renesas Salvator-X board based on r8a7796 (DT)
[ 20.413474] task: ffff80063b1f1900 task.stack: ffff80063a71c000
[ 20.419404] PC is at swiotlb_tbl_map_single+0x178/0x2ec
[ 20.424625] LR is at map_single+0x4c/0x98
[ 20.428629] pc : [<ffff00000839c4c0>] lr : [<ffff00000839c680>] pstate: 800001c5
[ 20.436019] sp : ffff80063a71f9b0
[ 20.439327] x29: ffff80063a71f9b0 x28: ffff80063a20d500
[ 20.444636] x27: ffff000008ed5000 x26: 0000000000000000
[ 20.449944] x25: 000000067abe2adc x24: 0000000000000000
[ 20.455252] x23: 0000000000200000 x22: 0000000000000001
[ 20.460559] x21: 0000000000175ffe x20: ffff80063b2a0010
[ 20.465866] x19: 0000000000000000 x18: 0000ffffcae6fb20
[ 20.471173] x17: 0000ffffa09ba018 x16: ffff0000087c8b70
[ 20.476480] x15: 0000ffffa084f588 x14: 0000ffffa09cfa14
[ 20.481787] x13: 0000ffffcae87ff0 x12: 000000000063abe2
[ 20.487098] x11: ffff000008096360 x10: ffff80063abe2adc
[ 20.492407] x9 : 0000000000000000 x8 : 0000000000000000
[ 20.497718] x7 : 0000000000000000 x6 : ffff000008ed50d0
[ 20.503028] x5 : 0000000000000000 x4 : 0000000000000001
[ 20.508338] x3 : 0000000000000000 x2 : 000000067abe2adc
[ 20.513648] x1 : 00000000bafff000 x0 : 0000000000000000
[ 20.518958]
[ 20.520446] Process mz (pid: 2089, stack limit = 0xffff80063a71c000)
[ 20.526798] Stack: (0xffff80063a71f9b0 to 0xffff80063a720000)
[ 20.532543] f9a0: ffff80063a71fa30 ffff00000839c680
[ 20.540374] f9c0: ffff80063b2a0010 ffff80063b2a0010 0000000000000001 0000000000000000
[ 20.548204] f9e0: 000000000000006e ffff80063b23c000 ffff80063b23c000 0000000000000000
[ 20.556034] fa00: ffff80063b23c000 ffff80063a20d500 000000013b1f1900 0000000000000000
[ 20.563864] fa20: ffff80063ffd18e0 ffff80063b2a0010 ffff80063a71fa60 ffff00000839cd10
[ 20.571694] fa40: ffff80063b2a0010 0000000000000000 ffff80063ffd18e0 000000067abe2adc
[ 20.579524] fa60: ffff80063a71fa90 ffff000008096380 ffff80063b2a0010 0000000000000000
[ 20.587353] fa80: 0000000000000000 0000000000000001 ffff80063a71fac0 ffff00000864f770
[ 20.595184] faa0: ffff80063b23caf0 0000000000000000 0000000000000000 0000000000000140
[ 20.603014] fac0: ffff80063a71fb60 ffff0000087e6498 ffff80063a20d500 ffff80063b23c000
[ 20.610843] fae0: 0000000000000000 ffff000008daeaf0 0000000000000000 ffff000008daeb00
[ 20.618673] fb00: ffff80063a71fc0c ffff000008da7000 ffff80063b23c090 ffff80063a44f000
[ 20.626503] fb20: 0000000000000000 ffff000008daeb00 ffff80063a71fc0c ffff000008da7000
[ 20.634333] fb40: ffff80063b23c090 0000000000000000 ffff800600000037 ffff0000087e63d8
[ 20.642163] fb60: ffff80063a71fbc0 ffff000008807510 ffff80063a692400 ffff80063a20d500
[ 20.649993] fb80: ffff80063a44f000 ffff80063b23c000 ffff80063a69249c 0000000000000000
[ 20.657823] fba0: 0000000000000000 ffff80063a087800 ffff80063b23c000 ffff80063a20d500
[ 20.665653] fbc0: ffff80063a71fc10 ffff0000087e67dc ffff80063a20d500 ffff80063a692400
[ 20.673483] fbe0: ffff80063b23c000 0000000000000000 ffff80063a44f000 ffff80063a69249c
[ 20.681312] fc00: ffff80063a5f1a10 000000103a087800 ffff80063a71fc70 ffff0000087e6b24
[ 20.689142] fc20: ffff80063a5f1a80 ffff80063a71fde8 000000000000000f 00000000000005ea
[ 20.696972] fc40: ffff80063a5f1a10 0000000000000000 000000000000000f ffff00000887fbd0
[ 20.704802] fc60: fffffff43a5f1a80 0000000000000000 ffff80063a71fc80 ffff000008880240
[ 20.712632] fc80: ffff80063a71fd90 ffff0000087c7a34 ffff80063afc7180 0000000000000000
[ 20.720462] fca0: 0000ffffcae6fe18 0000000000000014 0000000060000000 0000000000000015
[ 20.728292] fcc0: 0000000000000123 00000000000000ce ffff0000088d2000 ffff80063b1f1900
[ 20.736122] fce0: 0000000000008933 ffff000008e7cb80 ffff80063a71fd80 ffff0000087c50a4
[ 20.743951] fd00: 0000000000008933 ffff000008e7cb80 ffff000008e7cb80 000000100000000e
[ 20.751781] fd20: ffff80063a71fe4c 0000ffff00000300 0000000000000123 0000000000000000
[ 20.759611] fd40: 0000000000000000 ffff80063b1f0000 000000000000000e 0000000000000300
[ 20.767441] fd60: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 20.775271] fd80: 0000000000000000 0000000000000000 ffff80063a71fda0 ffff0000087c8c20
[ 20.783100] fda0: 0000000000000000 ffff000008082f30 0000000000000000 0000800637260000
[ 20.790930] fdc0: ffffffffffffffff 0000ffffa0903078 0000000000000000 000000001ea87232
[ 20.798760] fde0: 000000000000000f ffff80063a71fe40 ffff800600000014 ffff000000000001
[ 20.806590] fe00: 0000000000000000 0000000000000000 ffff80063a71fde8 0000000000000000
[ 20.814420] fe20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001
[ 20.822249] fe40: 0000000203000011 0000000000000000 0000000000000000 ffff80063a68aa00
[ 20.830079] fe60: ffff80063a68aa00 0000000000000003 0000000000008933 ffff0000081f1b9c
[ 20.837909] fe80: 0000000000000000 ffff000008082f30 0000000000000000 0000800637260000
[ 20.845739] fea0: ffffffffffffffff 0000ffffa07ca81c 0000000060000000 0000000000000015
[ 20.853569] fec0: 0000000000000003 000000001ea87232 000000000000000f 0000000000000000
[ 20.861399] fee0: 0000ffffcae6fe18 0000000000000014 0000000000000300 0000000000000000
[ 20.869228] ff00: 00000000000000ce 0000000000000000 00000000ffffffff 0000000000000000
[ 20.877059] ff20: 0000000000000002 0000ffffcae87ff0 0000ffffa09cfa14 0000ffffa084f588
[ 20.884888] ff40: 0000000000000000 0000ffffa09ba018 0000ffffcae6fb20 000000001ea87010
[ 20.892718] ff60: 0000ffffa09b9000 0000ffffcae6fe30 0000ffffcae6fe18 000000000000000f
[ 20.900548] ff80: 0000000000000003 000000001ea87232 0000000000000000 0000000000000000
[ 20.908378] ffa0: 0000000000000000 0000ffffcae6fdc0 0000ffffa09a7824 0000ffffcae6fdc0
[ 20.916208] ffc0: 0000ffffa0903078 0000000060000000 0000000000000003 00000000000000ce
[ 20.924038] ffe0: 0000000000000000 0000000000000000 ffffffffffffffff ffffffffffffffff
[ 20.931867] Call trace:
[ 20.934312] Exception stack(0xffff80063a71f7e0 to 0xffff80063a71f910)
[ 20.940750] f7e0: 0000000000000000 0001000000000000 ffff80063a71f9b0 ffff00000839c4c0
[ 20.948580] f800: ffff80063a71f840 ffff00000888a6e4 ffff80063a24c418 ffff80063a24c448
[ 20.956410] f820: 0000000000000000 ffff00000811cd54 ffff80063a71f860 ffff80063a24c458
[ 20.964240] f840: ffff80063a71f870 ffff00000888b258 ffff80063a24c418 0000000000000001
[ 20.972070] f860: ffff80063a71f910 ffff80063a7b7028 ffff80063a71f890 ffff0000088825e4
[ 20.979899] f880: 0000000000000000 00000000bafff000 000000067abe2adc 0000000000000000
[ 20.987729] f8a0: 0000000000000001 0000000000000000 ffff000008ed50d0 0000000000000000
[ 20.995560] f8c0: 0000000000000000 0000000000000000 ffff80063abe2adc ffff000008096360
[ 21.003390] f8e0: 000000000063abe2 0000ffffcae87ff0 0000ffffa09cfa14 0000ffffa084f588
[ 21.011219] f900: ffff0000087c8b70 0000ffffa09ba018
[ 21.016097] [<ffff00000839c4c0>] swiotlb_tbl_map_single+0x178/0x2ec
[ 21.022362] [<ffff00000839c680>] map_single+0x4c/0x98
[ 21.027411] [<ffff00000839cd10>] swiotlb_map_page+0xa4/0x138
[ 21.033072] [<ffff000008096380>] __swiotlb_map_page+0x20/0x7c
[ 21.038821] [<ffff00000864f770>] ravb_start_xmit+0x174/0x668
[ 21.044484] [<ffff0000087e6498>] dev_hard_start_xmit+0x8c/0x120
[ 21.050407] [<ffff000008807510>] sch_direct_xmit+0x108/0x1a0
[ 21.056064] [<ffff0000087e67dc>] __dev_queue_xmit+0x194/0x4cc
[ 21.061807] [<ffff0000087e6b24>] dev_queue_xmit+0x10/0x18
[ 21.067214] [<ffff000008880240>] packet_sendmsg+0xf40/0x1220
[ 21.072873] [<ffff0000087c7a34>] sock_sendmsg+0x18/0x2c
[ 21.078097] [<ffff0000087c8c20>] SyS_sendto+0xb0/0xf0
[ 21.083150] [<ffff000008082f30>] el0_svc_naked+0x24/0x28
[ 21.088462] Code: d34bfef7 2a1803f3 1a9f86d6 35fff878 (d4210000)
[ 21.094611] ---[ end trace 5bc544ad491f3814 ]---
[ 21.099234] Kernel panic - not syncing: Fatal exception in interrupt
[ 21.105587] Kernel Offset: disabled
[ 21.109073] Memory Limit: none
[ 21.112126] ---[ end Kernel panic - not syncing: Fatal exception in interrupt
Fixes: 2f45d1902acf ("ravb: minimize TX data copying")
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8cf699ec849f4ca1413cea01289bd7d37dbcc626 ]
Disable BH around the call to napi_schedule() to avoid following warning
[ 52.095499] NOHZ: local_softirq_pending 08
[ 52.421291] NOHZ: local_softirq_pending 08
[ 52.608313] NOHZ: local_softirq_pending 08
Fixes: 8d59de8f7bb3 ("net/mlx4_en: Process all completions in RX rings after port goes up")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 148d3d021cf9724fcf189ce4e525a094bbf5ce89 ]
The __bcm_sysport_tx_reclaim() function is used to reclaim transmit
resources in different places within the driver. Most of them should
not affect the state of the transit flow control.
Introduce bcm_sysport_tx_clean() which cleans the ring, but does not
re-enable flow control towards the networking stack, and make
bcm_sysport_tx_reclaim() do the actual transmit queue flow control.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 28e46a0f2e03ab4ed0e23cace1ea89a68c8c115b ]
The event_data starts from address 0x00-0x0C and not from 0x08-0x014. This
leads to duplication with other fields in the Event Queue Element such as
sub-type, cqn and owner.
Fixes: eda6500a987a0 ("mlxsw: Add PCI bus implementation")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
