| Age | Commit message (Collapse) | Author |
|---|
|
There is a common pattern in the driver where many SoCs need to write a
single register with a value dependent on the interface mode and speed.
Rather than having a lot of repeated code, add some common functions
and a struct to contain the values to be written to a register to
select the RGMII and RMII speeds.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uPk2t-004CFN-Td@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rather than having lots of regmap_write()s to the same register but
with different values depending on the speed, reorganise the
functions to use a local variable for the value, and then have one
regmap_write() call to write it to the register. This reduces the
amount of code and is a step towards further reducing the code size.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uPk2o-004CFH-Q4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RK platforms support RGMII and/or RMII depending on the SoC. Detect
whether support for a SoC exists by whether the interface specific
set_to functions have been populated, and set the appropriate bits in
phylink's bitmap of interfaces.
This assumes all dwmac interfaces on a SoC have identical support,
but it should be noted that this is not true for RK3528 which only
supports RGMII on GMAC1. However, the existing code structure
permits RGMII to be configured on GMAC0 without complaint, so
preserve this behaviour even though it is incorrect to avoid
functional change.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uPk2j-004CF6-Mf@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement a new admin command and helper function to handle and obtain
CGU measurements for input pins.
Add new callback operations to control the dpll device-level feature
"phase offset monitor," allowing it to be enabled or disabled. If the
feature is enabled, provide users with measured phase offsets and
notifications.
Initialize PPS DPLL with new callback operations if the feature is
supported by the firmware.
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250612152835.1703397-4-arkadiusz.kubalewski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add new callback operations for a dpll device:
- phase_offset_monitor_get(..) - to obtain current state of phase offset
monitor feature from dpll device,
- phase_offset_monitor_set(..) - to allow feature configuration.
Obtain the feature state value using the get callback and provide it to
the user if the device driver implements callbacks.
Execute the set callback upon user requests.
Reviewed-by: Milena Olech <milena.olech@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250612152835.1703397-3-arkadiusz.kubalewski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add enum dpll_feature_state for control over features.
Add dpll device level attribute:
DPLL_A_PHASE_OFFSET_MONITOR - to allow control over a phase offset monitor
feature. Attribute is present and shall return current state of a feature
(enum dpll_feature_state), if the device driver provides such capability,
otherwie attribute shall not be present.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250612152835.1703397-2-arkadiusz.kubalewski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Improve the .set_clk_tx_rate() method error message to include the
PHY interface mode along with the speed, which will be helpful to
the RK implementations.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1uPjjx-0049r5-NN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the PHY reset logic includes a role-specific asymmetric delay
to avoid synchronized reset deadlocks, the previously used randomized
polling intervals are no longer necessary.
This patch removes the get_random_u32_below()-based logic and introduces
an adaptive polling strategy:
- Fast polling for a short time after link-down
- Slow polling if the link remains down
- Slower polling when the link is up
This balances CPU usage and responsiveness while avoiding reset
collisions. Additionally, the driver still relies on polling for
all link state changes, as interrupt support is not implemented,
and link-up events are not reliably signaled by the PHY.
The polling parameters are now documented in the updated top-of-file
comment.
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250612104157.2262058-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that dp83tg720_soft_reset() introduces role-specific delays to avoid
reset synchronization deadlocks, the fixed 600ms post-reset delay in
dp83tg720_read_status() is no longer needed.
The new logic provides both the required MDC timing and link stabilization,
making the old empirical delay redundant and unnecessarily long.
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250612104157.2262058-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a .soft_reset callback for the DP83TG720 PHY that issues a hardware
reset followed by an asymmetric post-reset delay. The delay differs
based on the PHY's master/slave role to avoid synchronized reset
deadlocks, which are known to occur when both link partners use
identical reset intervals.
The delay includes:
- a fixed 1ms wait to satisfy MDC access timing per datasheet, and
- an empirically chosen extra delay (97ms for master, 149ms for slave).
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250612104157.2262058-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using a direct assignment instead of memcpy reduces the text segment
size from 0x273 bytes to 0x19b bytes in my case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/af371f2a-42f3-4d94-80b9-3420380a3f6f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's no need to include phy.h and mutex.h in mdio-boardinfo.h.
However mdio-boardinfo.c included phy.h indirectly this way so far,
include it explicitly instead. Whilst at it, sort the included
headers properly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/86b7a1d6-9f9c-4d22-b3d8-5abdef0bb39a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Struct mdio_board_entry isn't used outside mdio-boardinfo.c, so remove
the definition from the header file.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/0afe52d0-6fe6-434a-9881-3979661ff7b0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
- Move declaration of variable bi into list_for_each_entry_safe()
- The return value of cb() effectively isn't used, this allows to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/f6bbe242-b43d-4c2b-8c51-2cb2cefbaf59@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cancel any entries on the delayed work queue before starting
to tear down the lif to be sure there is no race with any
other events.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Joe Damato <joe@dama.to>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the kern_dbpage gets set up in ionic_lif_init() and that
function's error path will clean it if needed, the kern_dbpage
on teardown should be cleaned in ionic_lif_deinit(), not in
ionic_lif_free(). As it is currently we get a double call
to iounmap() on kern_dbpage if the PCI ionic fails setting up
the lif. One example of this is when firmware isn't responding
to AdminQ requests and ionic's first AdminQ call fails to
setup the NotifyQ.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Joe Damato <joe@dama.to>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware heartbeat value is an unsigned number, and seeing
a negative number when it gets big is a little disconcerting.
Example:
ionic 0000:24:00.0: FW heartbeat stalled at -1342169688
Print using the unsigned flag.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Joe Damato <joe@dama.to>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
irq_domain_create_simple() takes fwnode as the first argument. It can be
extracted from the struct device using dev_fwnode() helper instead of
using of_node with of_fwnode_handle().
So use the dev_fwnode() helper.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20250611104348.192092-15-jirislaby@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reduce verbosity by using gpiod_multi_set_value_cansleep() instead of
gpiod_set_array_value_cansleep().
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250611-net-mdio-mux-gpio-use-gpiod_multi_set_value_cansleep-v1-1-6eb5281f1b41@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Utilize netdev_sw_irq_coalesce_default_on() to provide conservative
default settings for GRO software interrupt coalescing.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20250611212730.252342-3-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make use of the return value from napi_complete_done(). This allows
users to use the gro_flush_timeout and napi_defer_hard_irqs sysfs
attributes for configuring software interrupt coalescing.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20250611212730.252342-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No driver should spam the kernel log when merely being loaded.
The message in hclge_init() is clearly a debug message.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jijie Shao<shaojijie@huawei.com>
Link: https://patch.msgid.link/c2ac6f20f85056e7b35bd56d424040f996d32109.1749657070.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify the arguments passed to phy_get_internal_delay() - the "dev"
argument is always &phydev->mdio.dev, and as the phydev is passed in,
there's no need to also pass in the struct device, especially when this
function is the only reason for the caller to have a local "dev"
variable.
Remove the redundant "dev" argument, and update the callers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1uPLwB-003VzR-4C@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
genphy_c45_read_status() is exported, so we can move definition of
genphy_c45_driver to phy_device.c and make it static. This helps
to clean up phy.h a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/ead3ab17-22d0-4cd3-901c-3d493ab851e6@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Hash based multicast filtering is an optional feature. Currently,
driver overrides the value of multicast_filter_bins based on the hash
table size. If the feature is not supported, hash table size reads 0
however the value of multicast_filter_bins remains set to default
HASH_TABLE_SIZE which is incorrect. Let's extend the use of the property
snps,multicast-filter-bins to xgmac so it can be set to 0 via devicetree
to indicate multicast filtering is not supported.
Signed-off-by: Nikunj Kela <nikunj.kela@sima.ai>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Link: https://patch.msgid.link/20250610200411.3751943-1-nikunj.kela@sima.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make mdio_device_bus_match() the default match function for non-PHY
MDIO devices. Benefit is that we don't have to export this function
any longer. As long as mdiodev->modalias isn't set, there's no change
in behavior. mdiobus_create_device() is the only place where
mdiodev->modalias gets set, but this function sets
mdio_device_bus_match() as match function anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/6c94e3d3-bfb0-4ddc-a518-6fddbc64e1d0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the new rxfh_fields callbacks, instead of de-muxing
the rxnfc calls. This driver does not support flow filtering so
the set_rxnfc callback is completely removed.
Link: https://patch.msgid.link/20250611145949.2674086-10-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the new rxfh_fields callbacks, instead of de-muxing
the rxnfc calls. This driver does not support flow filtering so
the set_rxnfc callback is completely removed.
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://patch.msgid.link/20250611145949.2674086-9-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the new rxfh_fields callbacks, instead of de-muxing
the rxnfc calls. This driver does not support flow filtering so
the set_rxnfc callback is completely removed.
Link: https://patch.msgid.link/20250611145949.2674086-8-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the new rxfh_fields callbacks, instead of de-muxing
the rxnfc calls. The code is moved as we try to declare the functions
in the order ing which they appear in the ops struct.
Link: https://patch.msgid.link/20250611145949.2674086-7-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We're migrating RXFH config to new callbacks.
Remove RXFH handling from drivers where it does nothing.
Reviewed-by: Ziwei Xiao <ziweixiao@google.com>
Link: https://patch.msgid.link/20250611145949.2674086-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RX Flow Hashing supports using different configuration for different
RSS contexts. Only two drivers seem to support it. Make sure we
uniformly error out for drivers which don't.
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20250611145949.2674086-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.16-rc2).
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Another quick round of updates:
- revert mwifiex HT40 that was causing issues
- many ath10k/ath11k/ath12k fixes
- re-add some iwlwifi code I lost in a merge
- use kfree_sensitive() on an error path in cfg80211
* tag 'wireless-2025-06-12' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: cfg80211: use kfree_sensitive() for connkeys cleanup
wifi: iwlwifi: fix merge damage related to iwl_pci_resume
Revert "wifi: mwifiex: Fix HT40 bandwidth issue."
wifi: ath12k: fix uaf in ath12k_core_init()
wifi: ath12k: Fix hal_reo_cmd_status kernel-doc
wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850
wifi: ath11k: validate ath11k_crypto_mode on top of ath11k_core_qmi_firmware_ready
wifi: ath11k: consistently use ath11k_mac_get_fw_stats()
wifi: ath11k: move locking outside of ath11k_mac_get_fw_stats()
wifi: ath11k: adjust unlock sequence in ath11k_update_stats_event()
wifi: ath11k: move some firmware stats related functions outside of debugfs
wifi: ath11k: don't wait when there is no vdev started
wifi: ath11k: don't use static variables in ath11k_debugfs_fw_stats_process()
wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
wil6210: fix support for sparrow chipsets
wifi: ath10k: Avoid vdev delete timeout when firmware is already down
ath10k: snoc: fix unbalanced IRQ enable in crash recovery
====================
Link: https://patch.msgid.link/20250612082519.11447-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netdevsim supports netpoll. Make sure we don't call napi_complete()
from it, since it may not be scheduled. Breno reports hitting a
warning in napi_complete_done():
WARNING: CPU: 14 PID: 104 at net/core/dev.c:6592 napi_complete_done+0x2cc/0x560
__napi_poll+0x2d8/0x3a0
handle_softirqs+0x1fe/0x710
This is presumably after netpoll stole the SCHED bit prematurely.
Reported-by: Breno Leitao <leitao@debian.org>
Fixes: 3762ec05a9fb ("netdevsim: add NAPI support")
Tested-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20250611174643.2769263-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Check for if ida_alloc() or rhashtable_lookup_get_insert_fast() fails.
Fixes: 17e0accac577 ("net/mlx5: HWS, support complex matchers")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Link: https://patch.msgid.link/aEmBONjyiF6z5yCV@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The veth peer device is RCU protected, but when the peer device gets
deleted (veth_dellink) then the pointer is assigned NULL (via
RCU_INIT_POINTER).
This patch adds a necessary NULL check in veth_xdp_rcv when accessing
the veth peer net_device.
This fixes a bug introduced in commit dc82a33297fc ("veth: apply qdisc
backpressure on full ptr_ring to reduce TX drops"). The bug is a race
and only triggers when having inflight packets on a veth that is being
deleted.
Reported-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Closes: https://lore.kernel.org/all/fecfcad0-7a16-42b8-bff2-66ee83a6e5c4@linux.dev/
Reported-by: syzbot+c4c7bf27f6b0c4bd97fe@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/683da55e.a00a0220.d8eae.0052.GAE@google.com/
Fixes: dc82a33297fc ("veth: apply qdisc backpressure on full ptr_ring to reduce TX drops")
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Acked-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Link: https://patch.msgid.link/174964557873.519608.10855046105237280978.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When performing a non-exact phy_caps lookup, we are looking for a
supported mode that matches as closely as possible the passed speed/duplex.
Blamed patch broke that logic by returning a match too early in case
the caller asks for half-duplex, as a full-duplex linkmode may match
first, and returned as a non-exact match without even trying to mach on
half-duplex modes.
Reported-by: Jijie Shao <shaojijie@huawei.com>
Closes: https://lore.kernel.org/netdev/20250603102500.4ec743cf@fedora/T/#m22ed60ca635c67dc7d9cbb47e8995b2beb5c1576
Tested-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Fixes: fc81e257d19f ("net: phy: phy_caps: Allow looking-up link caps based on speed and duplex")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250606094321.483602-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Apply conservative defaults.
Signed-off-by: Zak Kemble <zakkemble@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250610220403.935-3-zakkemble@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make use of the return value from napi_complete_done(). This allows users to
use the gro_flush_timeout and napi_defer_hard_irqs sysfs attributes for
configuring software interrupt coalescing.
Signed-off-by: Zak Kemble <zakkemble@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250610220403.935-2-zakkemble@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement the shutdown hook to ensure clean and complete deactivation of
MACB controller. The shutdown sequence is protected with 'rtnl_lock()'
to serialize access and prevent race conditions while detaching and
closing the network device. This ensure a safe transition when the Kexec
utility calls the shutdown hook, facilitating seamless loading and
booting of a new kernel from the currently running one.
Signed-off-by: Abin Joseph <abin.joseph@amd.com>
Link: https://patch.msgid.link/20250610114111.1708614-1-abin.joseph@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable cable test support for KSZ9477-class PHYs by reusing the
existing KSZ9131 implementation.
This also adds support for 100Mbit-only PHYs like KSZ8563, which are
identified as KSZ9477. For these PHYs, only two wire pairs (A and B)
are active, so the cable test logic limits the pair_mask accordingly.
Support for KSZ8563 is untested but added based on its register
compatibility and PHY ID match.
Tested on KSZ9893 (Gigabit): open and short conditions were correctly
detected on all four pairs. Fault length reporting is functional and
varies by pair. For example:
- 2m cable: open faults reported ~1.2m (pairs B–D), 0.0m (pair A)
- No cable: all pairs report 0.0m fault length
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250610091354.4060454-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PHYs
Add support for tracking receive error statistics from PHYs integrated
into the KSZ9477 family of Ethernet switches.
The integrated PHYs expose a receive error (RXER) counter in register 0x15.
This counter increments when the PHY detects one or more symbol errors
on a received frame. The register is cleared upon reading.
Changes include:
- `kszphy_update_stats()` to accumulate the RX error count.
- `kszphy_get_phy_stats()` to expose this count via ethtool PHY stats.
- Addition of a private `rx_err_pkt_cnt` field in the driver.
- Registration of `.update_stats` and `.get_phy_stats` callbacks in the
KSZ9477 PHY driver structure.
The functionality of this counter was confirmed by physically disturbing
the signal lines - specifically by wiggling exposed twisted pair wires and
intentionally shorting between pairs. These actions triggered RXER
increments, validating the counter's behavior.
This RXER counter is confirmed for KSZ9477 and likely applicable to
other related PHYs like those in KSZ9313.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250610091354.4060454-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
switch-integrated PHYs
Add MDI/MDI-X configuration support for PHYs integrated in the KSZ9477
family of Ethernet switches.
All MDI/MDI-X configuration modes are supported:
- Automatic MDI/MDI-X (ETH_TP_MDI_AUTO)
- Forced MDI (ETH_TP_MDI)
- Forced MDI-X (ETH_TP_MDI_X)
However, when operating in automatic mode, the PHY does not expose the
resolved crossover status (i.e., whether MDI or MDI-X is active).
Therefore, in auto mode, the driver reports ETH_TP_MDI_INVALID as
the current status.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250610091354.4060454-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Expand coverage of MAC stats via ethtool by adding rmon and eth-ctrl
stats.
ethtool -S eth0 --groups eth-ctrl
Standard stats for eth0:
eth-ctrl-MACControlFramesTransmitted: 0
eth-ctrl-MACControlFramesReceived: 0
ethtool -S eth0 --groups rmon
Standard stats for eth0:
rmon-etherStatsUndersizePkts: 0
rmon-etherStatsOversizePkts: 0
rmon-etherStatsFragments: 0
rmon-etherStatsJabbers: 0
rx-rmon-etherStatsPkts64Octets: 32807689
rx-rmon-etherStatsPkts65to127Octets: 567512968
rx-rmon-etherStatsPkts128to255Octets: 64730266
rx-rmon-etherStatsPkts256to511Octets: 20136039
rx-rmon-etherStatsPkts512to1023Octets: 28476870
rx-rmon-etherStatsPkts1024to1518Octets: 6958335
rx-rmon-etherStatsPkts1519to2047Octets: 164
rx-rmon-etherStatsPkts2048to4095Octets: 3844
rx-rmon-etherStatsPkts4096to8191Octets: 21814
rx-rmon-etherStatsPkts8192to9216Octets: 6540818
rx-rmon-etherStatsPkts9217to9742Octets: 4180897
tx-rmon-etherStatsPkts64Octets: 8786
tx-rmon-etherStatsPkts65to127Octets: 31475804
tx-rmon-etherStatsPkts128to255Octets: 3581331
tx-rmon-etherStatsPkts256to511Octets: 2483038
tx-rmon-etherStatsPkts512to1023Octets: 4500916
tx-rmon-etherStatsPkts1024to1518Octets: 38741270
tx-rmon-etherStatsPkts1519to2047Octets: 15521
tx-rmon-etherStatsPkts2048to4095Octets: 4109
tx-rmon-etherStatsPkts4096to8191Octets: 20817
tx-rmon-etherStatsPkts8192to9216Octets: 6904055
tx-rmon-etherStatsPkts9217to9742Octets: 6757746
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250610171109.1481229-3-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the link is up, either eth_proto_oper or ext_eth_proto_oper
typically reports the active link protocol, from which both speed
and number of lanes can be retrieved. However, in certain cases,
such as when a NIC is connected via a non-standard cable, the
firmware may not report the protocol.
In such scenarios, the speed can still be obtained from the
data_rate_oper field in PTYS register. Since data_rate_oper
provides only speed information and lacks lane details, it is
incorrect to derive the number of lanes from it.
This patch corrects the behavior by setting the number of lanes to
UNKNOWN instead of incorrectly using MAX_LANES when relying on
data_rate_oper.
Fixes: 7e959797f021 ("net/mlx5e: Enable lanes configuration when auto-negotiation is off")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-10-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, a unique tunnel id was added for the matching on TC
non-zero chains, to support inner header rewrite with goto action.
Later, it was used to support VF tunnel offload for vxlan, then for
Geneve and GRE. To support VF tunnel, a temporary mlx5_flow_spec is
used to parse tunnel options. For Geneve, if there is TLV option, a
object is created, or refcnt is added if already exists. But the
temporary mlx5_flow_spec is directly freed after parsing, which causes
the leak because no information regarding the object is saved in
flow's mlx5_flow_spec, which is used to free the object when deleting
the flow.
To fix the leak, call mlx5_geneve_tlv_option_del() before free the
temporary spec if it has TLV object.
Fixes: 521933cdc4aa ("net/mlx5e: Support Geneve and GRE with VF tunnel offload")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Alex Lazar <alazar@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-9-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When there are more than one destinations, we create a FW flow
table and provide it with all the destinations. FW requires to
have wire as the last destination in the list (if it exists),
otherwise the operation fails with FW syndrome.
This patch fixes the destination array action creation: if it
contains a wire destination, it is moved to the end.
Fixes: 504e536d9010 ("net/mlx5: HWS, added actions handling")
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-7-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix missing field handling in definer - outer IP version.
Fixes: 74a778b4a63f ("net/mlx5: HWS, added definers handling")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
