Age | Commit message (Collapse) | Author |
|
v58->v59:
- Keep uC USB buffer unchanged for about 1 second when exiting suspend
mode, in order to fix false wakeup events issue
Change-Id: I175bb0328af1840cbfe8c70e0607d7d8023e0c26
Signed-off-by: Jun Yan <juyan@nvidia.com>
(cherry picked from commit 5f337115955a3dffa7b2522c43f9844f8416bec7)
Reviewed-on: http://git-master/r/243054
GVS: Gerrit_Virtual_Submit
Reviewed-by: Anshul Jain (SW) <anshulj@nvidia.com>
|
|
v57->v58
-changed dead band to 38
-changed cal window to 80
Bug 1266521
Change-Id: I686ef709df77ad7d29e8cee6420683ee901a73cf
Signed-off-by: Jun Yan <juyan@nvidia.com>
(cherry picked from commit 20434a424e4c535f8105bd26a220ae6f1f999067)
Reviewed-on: http://git-master/r/237706
Reviewed-by: Automatic_Commit_Validation_User
GVS: Gerrit_Virtual_Submit
Reviewed-by: Anshul Jain (SW) <anshulj@nvidia.com>
|
|
v56->v57
added changes to uC FW that will check to make sure if LED PWM timer0 == Started then check the timer0 start bit and if not set
then set it to start running again.
v55->v56
- Bump revision to v0_56.
- Changed the following End Point 2 commands:
LED_UC_DRIVE- This function now does Nothing. Left it in for backwards compatibility.
(Previously this function setup the Port 1.1 pin to drive from tri-state. And also set the LED pin high (ON).)
LED_BREATHE_ON- This function now sets up port 1.1 in a drive state from tri-state and starts timer0 for the SW PWM.
LED_BREATHE_OFF- This function now sets up port 1.1 in a drive state from tri-state.
Also keeps the same logic as before stopping the SW PWM timer0 and set P1.1 LED LOW (OFF).
Bug 1266521
Change-Id: I2ef12fe6c66e03d299b0135e749498d8154f3937
Signed-off-by: Anshul Jain <anshulj@nvidia.com>
(cherry picked from commit 95b376f67b759bf783c76cc6701d9103d065ada5)
Reviewed-on: http://git-master/r/237705
Reviewed-by: Jun Yan <juyan@nvidia.com>
Tested-by: Jun Yan <juyan@nvidia.com>
Reviewed-by: Automatic_Commit_Validation_User
GVS: Gerrit_Virtual_Submit
|
|
- Bump revsion to v0_55.
- Center point calibration window (power on/reset) now 40 from 80
- power on defaults for Right/Left Joystick X,Y axes are now 250 from150.
Note: doing this makes the scaling values less granular or smaller steps on power on.
Thus helps with RS mouse drift being a larger value just outside the center dead band.
Noticed that the RS mouse drift can go away after moving the joysticks to its max and min points.
- power on defaults for right/left analog triggers are now 600 and 300 max/min.
The original version had this at 300 and 700 reversed. Hence, on the very first trigger pull,
you only had to move a very small distance to hit max.
NOTE: Center point stiction dead band is still set to 37. Same as v52.
Bug 1266521
Change-Id: I071c9b1ef2cb837787fd4f21f0e4a6bee9aafc01
Signed-off-by: Anshul Jain <anshulj@nvidia.com>
(cherry picked from commit b2528f22257dcbd32e7e89113d5a532376ef95a5)
Reviewed-on: http://git-master/r/237704
Reviewed-by: Jun Yan <juyan@nvidia.com>
Tested-by: Jun Yan <juyan@nvidia.com>
Reviewed-by: Automatic_Commit_Validation_User
GVS: Gerrit_Virtual_Submit
|
|
v51->v52
- Bump revsion to v0_52.
- All Joystick Wakeup out of Suspend Tuning changes:
- Added a ADC Channel Synchronizer so as to make the Left and right joystick axes has a higher suspend mid point value.
This helps the sensitivity when moving the POT towards the GND node.
- Because of the ADC channels Sychronizer the Left and Right Analog triggers needed more Threshold tuning:
now Left Analog Trigger threshold is < 100 (was 150) and Right Analog Trigger Threshold is > 350 (was 375)
This helped move the wakeup trigger point more away from the ends.
- For the Left and Right Joysticks; we added two Thresholds wakeup methods:
1) the original dADC/dt with a delta threshold of 80. same as v46.
2) a "Measured" suspend MID-point min and max threshold.
This helps wake up when user move joystick slowly to one side or the other.
Measured absolute Thresholds are set to suspend mid point- 150 and + 150.
If suspend mid-point is too low then we will default to a low threhold of 85.
v46->v51
- Bump revsion to v0_51. This has everything that v46 has.
- Has joystick wakeup and Left and Right Analog trigger wake up.
- Analog triggers use a fixed absolute threshold: Left is set to < 150 and Right is set to > 375
- The Left and Right Joysticks still are using dADC/dt methodolgy with a threshold of 80.
However, it can be a little difficult to wake up using these. Especally if the using moves towards GND side of the POT.
Bug 1266521
Change-Id: I2322d0265fac69314368d025656e3fef8d3be414
Signed-off-by: Anshul Jain <anshulj@nvidia.com>
(cherry picked from commit 9d0f6ae86de61f3360932b1598e8da18b0fe7404)
Reviewed-on: http://git-master/r/229465
Reviewed-by: Automatic_Commit_Validation_User
|
|
v40->v46
- Removed Debug GPIO P3.0
- No wakeup pulse sent in OS Idle/Display Off (aka Active/LED Breathing ON)
- If LED Breathing remains ON when Display is ON, will turn off LED
Breathing with button press or Joystick Motion (no Analog Triggers).
LED breathing on in this state is a DON’T care because Tegra is
overriding the LED control.
- Added back Joystick wakeup during USB Suspend. Only Left
and Right Analog sticks and NO Analog Triggers.
- Suspend Joystick wakeup Threshold is set to 80.
- Added a usb activity check before the LED control logic in the suspend loop. If usb activity detected; we will bail out of the loop.
This change more matches v31 suspend loop that seems to be running LP0 suspend/resume cycles just fine.
Noticed on the scope that the timing delta relationship from Resume to T-setup requests were varying quite a lot. The LED control logic
just seems to be the reason for the large timing jitter.
- Added Port 3.0 debug toggle in the following functions:
* uC Waiting for USB enumeration packets from the Host.
* While loop LED timer0 in the beginning of Suspend; Will toggle P3.0.
- While LED timer0 ISR timeouts are still implemented.
- LED flicker fix
Bug 1276644
Bug 1285468
Bug 1266521
Bug 1283114
Change-Id: I609742ea3aae5b84a90a929bb19db0b2edd4c576
Signed-off-by: Anshul Jain <anshulj@nvidia.com>
Reviewed-on: http://git-master/r/227147
Reviewed-on: http://git-master/r/228579
Reviewed-by: Automatic_Commit_Validation_User
|
|
v39->v40
Updates the guard band to 37
Bug 1282562
Change-Id: Ifd2e2c9803a2af0311a4017bec878f94522085b7
Signed-off-by: Anshul Jain <anshulj@nvidia.com>
Reviewed-on: http://git-master/r/225341
Reviewed-by: Automatic_Commit_Validation_User
|
|
P2560 v0_38->v0_39
- Bump revsion to v0_39.
- Changed LED feed-forward table for optimal breathing cycle.
- LED Flicker fix when plugging and unplugging USB power. (aka Tegra goes into LP0 and into Idle/screen off.)
- Clear NAK counter and state when going from Suspend to active with LED_UC_DRIVE set.
- Make sure Suspend state if fully clear out of suspend; so we can respond to USB packets from tegra.
- Mure sure wakeup Puluse gets cleared when going from Suspend to active/LED_UC_DRIVE. flag was not getting cleared in active state.
- USB Descriptor name change "NVIDIA Corporation" "NVIDIA Controller v01.01"
- NAK 1 second code is still activiated.
P2454 v0_30->v0_31
- Same as v0_30 expect USB decriptor name change "NVIDIA Corporation" "NVIDIA Controller v01.01"
Bug 1266521
Change-Id: Ibc8b3bfbbc1c8f676ec4cb0e7c399346797ce653
Signed-off-by: Anshul Jain <anshulj@nvidia.com>
Reviewed-on: http://git-master/r/223927
Reviewed-by: Automatic_Commit_Validation_User
|
|
P2454
v30 change to make revision readable
P2560
v37->v38
- Bump revsion to v0_38.
- Change PID o 7203.
- change minimum PWM% to 4%.
- improve LED breathing jitter when sending wakeup pulse in active and suspend
mode.
- add LED control Feed Forward Table method to adjust the LED smoothness and
cycling time.
- adjust LED breathing behavior according to POR
- NAK 1 second code is still activiated.
Bug 1266521
Change-Id: I3514da906d1baf9d7ed159f92d1fc82c0e1796f1
Signed-off-by: Anshul Jain <anshulj@nvidia.com>
Reviewed-on: http://git-master/r/222692
Reviewed-by: Richard Zhao <rizhao@nvidia.com>
Reviewed-by: Automatic_Commit_Validation_User
GVS: Gerrit_Virtual_Submit
|
|
This change separates issp device configuration for p2454 and
p2560 boards.
This change also downgrades the JS firmware P2454 from v37 to
v30. Also, it creates a node for p2560 with v37.
Bug 1266521
Bug 1270341
Bug 1276644
Change-Id: Ibb4b59d48146b71a8dec83c2460716299f38a0fc
Signed-off-by: Anshul Jain <anshulj@nvidia.com>
Reviewed-on: http://git-master/r/222599
Reviewed-by: Simone Willett <swillett@nvidia.com>
Tested-by: Simone Willett <swillett@nvidia.com>
|
|
P2560_v0_37_7202_LED_LowPWMjittefix_wakeupinactive.hex
- Bump revsion to v0_37
- LED Breathing Jitter at LOW PWM% in Active state( Tegra in Idle with
Screen OFF, Sends LED_UC_DRIVE command to uC)
- Wakeup Pulse is now being sent (ISSP_DAT) to GMI_IORDY (WAKE23) when
uC is in active state with Tegra in idle screen OFF.
Joystick sensitivity may need to tuned some more. Kept the sensitivity
LOW (100) for now because of the Polyshine Joysticks.
- LED Breathing Cycle timing tweaks.
Still needs further timing tuning. Vic says we are still a little
unsmooth. We are 85% to 90% perfect.
- NAK 1 second code is still activiated.
Bug 1266521
Change-Id: I9b2629a2dfc1e12276e753bf6a17da3ebd9298dd
Signed-off-by: Richard Zhao <rizhao@nvidia.com>
Reviewed-on: http://git-master/r/220434
Reviewed-by: Automatic_Commit_Validation_User
GVS: Gerrit_Virtual_Submit
Reviewed-by: Matt Wagner <mwagner@nvidia.com>
|
|
Customer wanted to have the LED go on after key press or Joystick motion.
Needed to drive LED high for ~700ms( added lots of Margin) after wake up
pulse because Tegra needed time (xxx ms) to drive LED after LP0.
This prevents the LED from going OFF then ON flicker. Provided you hit
a key when the LED is on.
Bug 1266521
Change-Id: Id463fa9576744fb4e581497bfc289814b71e4adf
Signed-off-by: Richard Zhao <rizhao@nvidia.com>
Reviewed-on: http://git-master/r/217610
Reviewed-by: Automatic_Commit_Validation_User
GVS: Gerrit_Virtual_Submit
Reviewed-by: Matt Wagner <mwagner@nvidia.com>
|
|
issp is used to program roth on-board joystick micro controller.
This driver adds:
- issp platform device
- firmware for micro controller P2560_v0_34_not_readprotect_0280.hex
- add issp to tegra11_android_defconfig
Bug 1245803
Change-Id: Idaddbbe8e853744da7f09bb846f47374ebe841b9
Signed-off-by: Richard Zhao <rizhao@nvidia.com>
Reviewed-on: http://git-master/r/209785
Reviewed-by: Simone Willett <swillett@nvidia.com>
Tested-by: Simone Willett <swillett@nvidia.com>
|
|
This parameter blob and generator program have been moved to the
linux-firmware.git repository.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
David and I are sharing maintenance of this repository. Patches
should be sent to both of us.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
C0 silicon updates the pci revision id and requires new AFE parameters
for phy signal integrity. Support for previous silicon revisions is
deprecated (it's also broken for the theoretical case of multiple
controllers at different silicon revisions, all the more reason to get
it removed as soon as possible)
Signed-off-by: Adam Gruchala <adam.gruchala@intel.com>
[fixed up deprecated silicon support]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The element_length is 2 bytes.
Reported-by: Yinghai Lu <yinghai.lu@oracle.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The original apc mode definition is the correct one, the fix from commit
4711ba10 "isci: fix oem parameter initialization and mode detection" was based
on a typo from a specification update.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
1/ Since commit 858d4aa7 "isci: Move firmware loading to per PCI device" we have
been silently falling back to built-in defaults for the parameter settings by
skipping the call to scic_oem_parameters_set().
2/ The afe parameters from the firmware were not being honored
3/ The latest oem parameter definition flips the mode_type values which are
now 0: for APC 1: for MPC. For APC we need to make sure all the phys
default to the same address otherwise strict_wide_ports will cause duplicate
domains.
4/ Fix up the driver announcement to indicate the source of the
parameters.
5/ Fix up the sas addresses to be unique per controller (in the fallback case)
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
1/ add OEM paramater support for mode_type (MPC vs APC)
2/ add OEM parameter support for max_number_concurrent_device_spin_up
3/ cleanup scic_sds_controller_start_next_phy
todo: hook up the amp control afe parameters into the afe init code
Signed-off-by: Henryk Dembkowski <henryk.dembkowski@intel.com>
Signed-off-by: Jacek Danecki <Jacek.Danecki@intel.com>
[cleaned up scic_sds_controller_start_next_phy]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
We need to scan the OROM for signature and grab the OEM parameters. We
also need to do the same for EFI. If all fails then we resort to user
binary blob, and if that fails then we go to the defaults.
Share the format with the create_fw utility so that all possible sources
of the parameters are in-sync.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Support for the up to 2x4-port 6Gb/s SAS controllers embedded in the
chipset.
This is a snapshot of the first publicly available version of the driver,
commit 4c1db2d0 in the 'historical' branch.
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/isci.git historical
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Edmund Nadolski <edmund.nadolski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
To fix bugs when running offloaded FCoE/iSCSI traffic in multiple
Class of Service environments. In some scenarios, traffic could stop
on certain rings and eventually all traffic would stop.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update 5709 mips firmware to 6.2.1a to fix iSCSI performance
regression. There was an unnecessary context read in the fast path
affecting performance.
Update bnx2 to 2.1.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix unusued return value compiler warnings due to unchecked write() calls.
[akpm@linux-foundation.org: correctly handle short writes]
Signed-off-by: Chris Ruffin <cmruffin@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update MIPS firmware to 6.2.1, with improved small packet performance
in RSS mode, and iSCSI CID allocation bug fix on 5708.
Update driver version to 2.0.21.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Includes FCoE releated fixes in FW flows
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ihex firmwares can include a jump address for starting execution. Add a
-j option which will cause this to be written into the generated file as a
record with address zero and data consisting of the address to jump to,
allowing drivers to make use of this information.
This format is chosen because it most closely follows the original ihex
format, though it may make more sense to write a record with length zero
and the address stored as the address. The records are not omitted by
default since our ihex format does not include record type information and
so including additional records may lead to confusion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
Update broken web addresses in arch directory.
Update broken web addresses in the kernel.
Revert "drivers/usb: Remove unnecessary return's from void functions" for musb gadget
Revert "Fix typo: configuation => configuration" partially
ida: document IDA_BITMAP_LONGS calculation
ext2: fix a typo on comment in ext2/inode.c
drivers/scsi: Remove unnecessary casts of private_data
drivers/s390: Remove unnecessary casts of private_data
net/sunrpc/rpc_pipe.c: Remove unnecessary casts of private_data
drivers/infiniband: Remove unnecessary casts of private_data
drivers/gpu/drm: Remove unnecessary casts of private_data
kernel/pm_qos_params.c: Remove unnecessary casts of private_data
fs/ecryptfs: Remove unnecessary casts of private_data
fs/seq_file.c: Remove unnecessary casts of private_data
arm: uengine.c: remove C99 comments
arm: scoop.c: remove C99 comments
Fix typo configue => configure in comments
Fix typo: configuation => configuration
Fix typo interrest[ing|ed] => interest[ing|ed]
Fix various typos of valid in comments
...
Fix up trivial conflicts in:
drivers/char/ipmi/ipmi_si_intf.c
drivers/usb/gadget/rndis.c
net/irda/irnet/irnet_ppp.c
|
|
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
- Improved flow control and simplified interface
- Use hardware RSS indirection table instead of the slower firmware-
based table
- Lower latency interrupt on 5709
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
57712 HW supported with same set of features as for 57710/57711
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the new FW HSI blob and the relevant definitions without logic changes.
It also included code adaptation for new HSI. New features are not enabled.
New FW/HSI includes:
- Support for 57712 HW
- Future support for VF (not used)
- Improvements in FW interrupts scheme
- FW FCoE hooks (stubs for future usage)
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New firmware files for all bnx2x devices
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
It doesn't like pattern and explicit rules to be on the same line,
and it seems to be more picky when matching file (or really directory)
names with different numbers of trailing slashes.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Andrew Benton <b3nton@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
|
|
Extract the microcode for the QLogic QLE7220 series IB HCA and use the
kernel microcode request facility to load the microcode. This
supports Debian Linux's requirements to separate microcode which
doesn't have open source code available from the device driver.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Update FW to 7.10
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New firmware fixes a performance regression on small packets.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed FW 5.2.7.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch to the new firmware version (5.2.13).
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New firmware version (5.2.13).
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Increase FTQ depth to 256 to ehnabce performance.
- Fix RV2P context corruption on 5709 when flow control is enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pcnet_cs,serial_cs:
add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|