| Age | Commit message (Collapse) | Author |
|---|
|
So forever we have had this thing to limit the amount of delalloc pages we'll
setup to be written out to 128mb. This is because we have to lock all the pages
in this range, so anything above this gets a bit unweildly, and also without a
limit we'll happily allocate gigantic chunks of disk space. Turns out our check
for this wasn't quite right, we wouldn't actually limit the chunk we wanted to
write out, we'd just stop looking for more space after we went over the limit.
So if you do a giant 20gb dd on my box with lots of ram I could get 2gig
extents. This is fine normally, except when you go to relocate these extents
and we can't find enough space to relocate these moster extents, since we have
to be able to allocate exactly the same sized extent to move it around. So fix
this by actually enforcing the limit. With this patch I'm no longer seeing
giant 1.5gb extents. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
PAGE_CACHE_SIZE == PAGE_SIZE is "unsigned long" everywhere, so there's no
need to cast it to "unsigned long".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
u64 is "unsigned long long" on all architectures now, so there's no need to
cast it when formatting it using the "ll" length modifier.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
Cc: Josef Bacik <jbacik@fusionio.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
make C=2 fs/btrfs/ CF=-D__CHECK_ENDIAN__
I tried to filter out the warnings for which patches have already
been sent to the mailing list, pending for inclusion in btrfs-next.
All these changes should be obviously safe.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
We want this for btrfs_extent_same. Basically readpage and friends do their
own extent locking but for the purposes of dedupe, we want to have both
files locked down across a set of readpage operations (so that we can
compare data). Introduce this variant and a flag which can be set for
extent_read_full_page() to indicate that we are already locked.
Partial credit for this patch goes to Gabriel de Perthuis <g2p.code@gmail.com>
as I have included a fix from him to the original patch which avoids a
deadlock on compressed extents.
Signed-off-by: Mark Fasheh <mfasheh@suse.de>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
There is no reason we can't just set the path to blocking and then do normal
GFP_NOFS allocations for these extent buffers. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
We can get ENOMEM trying to allocate dummy bufs for the rewind operation of the
tree mod log. Instead of BUG_ON()'ing in this case pass up ENOMEM. I looked
back through the callers and I'm pretty sure I got everybody who did BUG_ON(ret)
in this path. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
This patch removes the io_tree argument for extent_clear_unlock_delalloc since
we always use &BTRFS_I(inode)->io_tree, and it separates out the extent tree
operations from the page operations. This way we just pass in the extent bits
we want to clear and then pass in the operations we want done to the pages.
This is because I'm going to fix what extent bits we clear in some cases and
rather than add a bunch of new flags we'll just use the actual extent bits we
want to clear. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
When we read several pages at once, we needn't get the extent map object
every time we deal with a page, and we can cache the extent map object.
So, we can reduce the search time of the extent map, and besides that, we
also can reduce the lock contention of the extent map tree.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
In the past, we cached the checksum value in the extent state object, so we
had to split the extent state object by the block size, or we had no space
to keep this checksum value. But it increased the lock contention of the
extent state tree.
Now we removed this limit by caching the checksum into the bio object, so
it is unnecessary to do the extent state operations by the block size, we
can do it in batches, in this way, we can reduce the lock contention of
the extent state tree.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
Before applying this patch, we set the uptodate flag and unlock the extent
by the page size, it is unnecessary, we can do it in batches, it can reduce
the lock contention of the extent state tree.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
Before applying this patch, we cached the csum value into the extent state
tree when reading some data from the disk, this operation increased the lock
contention of the state tree.
Now, we just store the csum value into the bio structure or other unshared
structure, so we can reduce the lock contention.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
This patch add some branch prediction hints into the end IO function
of the read page, it reduced the percentage of the branch misses from
5.5% to 4.9%.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
xfstest btrfs/276 was freaking out on slower boxes partly because fiemap was
offsetting the physical based on the extent offset. This is perfectly fine with
uncompressed extents, however the extent offset is into the uncompressed area,
not the compressed. So we can return a physical value that isn't at all within
the area we have allocated on disk. Fix this by returning the start of the
extent if it is compressed no matter what the offset. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs update from Chris Mason:
"These are the usual mixture of bugs, cleanups and performance fixes.
Miao has some really nice tuning of our crc code as well as our
transaction commits.
Josef is peeling off more and more problems related to early enospc,
and has a number of important bug fixes in here too"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (81 commits)
Btrfs: wait ordered range before doing direct io
Btrfs: only do the tree_mod_log_free_eb if this is our last ref
Btrfs: hold the tree mod lock in __tree_mod_log_rewind
Btrfs: make backref walking code handle skinny metadata
Btrfs: fix crash regarding to ulist_add_merge
Btrfs: fix several potential problems in copy_nocow_pages_for_inode
Btrfs: cleanup the code of copy_nocow_pages_for_inode()
Btrfs: fix oops when recovering the file data by scrub function
Btrfs: make the chunk allocator completely tree lockless
Btrfs: cleanup orphaned root orphan item
Btrfs: fix wrong mirror number tuning
Btrfs: cleanup redundant code in btrfs_submit_direct()
Btrfs: remove btrfs_sector_sum structure
Btrfs: check if we can nocow if we don't have data space
Btrfs: stop using try_to_writeback_inodes_sb_nr to flush delalloc
Btrfs: use a percpu to keep track of possibly pinned bytes
Btrfs: check for actual acls rather than just xattrs when caching no acl
Btrfs: move btrfs_truncate_page to btrfs_cont_expand instead of btrfs_truncate
Btrfs: optimize reada_for_balance
Btrfs: optimize read_block_for_search
...
|
|
We always just try and reserve data space when we write, but if we are out of
space but have prealloc'ed extents we should still successfully write. This
patch will try and see if we can write to prealloc'ed space and if we can go
ahead and allow the write to continue. With this patch we now pass xfstests
generic/274. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
This has plagued us forever and I'm so over working around it. When we truncate
down to a non-page aligned offset we will call btrfs_truncate_page to zero out
the end of the page and write it back to disk, this will keep us from exposing
stale data if we truncate back up from that point. The problem with this is it
requires data space to do this, and people don't really expect to get ENOSPC
from truncate() for these sort of things. This also tends to bite the orphan
cleanup stuff too which keeps people from mounting. To get around this we can
just move this into btrfs_cont_expand() to make sure if we are truncating up
from a non-page size aligned i_size we will zero out the rest of this page so
that we don't expose stale data. This will give ENOSPC if you try to truncate()
up or if you try to write past the end of isize, which is much more reasonable.
This fixes xfstests generic/083 failing to mount because of the orphan cleanup
failing. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
The 'end' value must exactly cover the end of the interval, which means
one byte less than the expected block alignment, or in case of a file
smaller than one block, one byte less than the inode size.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
Currently there is no way to truncate partial page where the end
truncate point is not at the end of the page. This is because it was not
needed and the functionality was enough for file system truncate
operation to work properly. However more file systems now support punch
hole feature and it can benefit from mm supporting truncating page just
up to the certain point.
Specifically, with this functionality truncate_inode_pages_range() can
be changed so it supports truncating partial page at the end of the
range (currently it will BUG_ON() if 'end' is not at the end of the
page).
This commit changes the invalidatepage() address space operation
prototype to accept range to be invalidated and update all the instances
for it.
We also change the block_invalidatepage() in the same way and actually
make a use of the new length argument implementing range invalidation.
Actual file system implementations will follow except the file systems
where the changes are really simple and should not change the behaviour
in any way .Implementation for truncate_page_range() which will be able
to accept page unaligned ranges will follow as well.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hugh Dickins <hughd@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Miao Xie has been very busy, fixing races and enospc problems and many
other small but important pieces.
Alexandre Oliva discovered some problems with how our error handling
was interacting with the block layer and for now has disabled our
partial handling of sub-page writes. The real sub-page work is in a
series of patches from IBM that we still need to integrate and test.
The code Alexandre has turned off was really incomplete.
Josef has more error handling fixes and an important fix for the new
skinny extent format.
This also has my fix for the tracepoint crash from late in 3.9. It's
the first stage in a larger clean up to get rid of btrfs_bio and make
a proper bioset for all the items we need to tack into the bio. For
now the bioset only holds our mirror_num and stripe_index, but for the
next merge window I'll shuffle more in."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
Btrfs: use a btrfs bioset instead of abusing bio internals
Btrfs: make sure roots are assigned before freeing their nodes
Btrfs: explicitly use global_block_rsv for quota_tree
btrfs: do away with non-whole_page extent I/O
Btrfs: don't invoke btrfs_invalidate_inodes() in the spin lock context
Btrfs: remove BUG_ON() in btrfs_read_fs_tree_no_radix()
Btrfs: pause the space balance when remounting to R/O
Btrfs: fix unprotected root node of the subvolume's inode rb-tree
Btrfs: fix accessing a freed tree root
Btrfs: return errno if possible when we fail to allocate memory
Btrfs: update the global reserve if it is empty
Btrfs: don't steal the reserved space from the global reserve if their space type is different
Btrfs: optimize the error handle of use_block_rsv()
Btrfs: don't use global block reservation for inode cache truncation
Btrfs: don't abort the current transaction if there is no enough space for inode cache
Correct allowed raid levels on balance.
Btrfs: fix possible memory leak in replace_path()
Btrfs: fix possible memory leak in the find_parent_nodes()
Btrfs: don't allow device replace on RAID5/RAID6
Btrfs: handle running extent ops with skinny metadata
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/josef/btrfs-next
|
|
Btrfs has been pointer tagging bi_private and using bi_bdev
to store the stripe index and mirror number of failed IOs.
As bios bubble back up through the call chain, we use these
to decide if and how to retry our IOs. They are also used
to count IO failures on a per device basis.
Recently a bio tracepoint was added lead to crashes because
we were abusing bi_bdev.
This commit adds a btrfs bioset, and creates explicit fields
for the mirror number and stripe index. The plan is to
extend this structure for all of the fields currently in
struct btrfs_bio, which will mean one less kmalloc in
our IO path.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Reported-by: Tejun Heo <tj@kernel.org>
|
|
end_bio_extent_readpage computes whole_page based on bv_offset and
bv_len, without taking into account that blk_update_request may modify
them when some of the blocks to be read into a page produce a read
error. This would cause the read to unlock only part of the file
range associated with the page, which would in turn leave the entire
page locked, which would not only keep the process blocked instead of
returning -EIO to it, but also prevent any further access to the file.
It turns out that btrfs always issues whole-page reads and writes.
The special handling of non-whole_page appears to be a mistake or a
left-over from a time when this wasn't the case. Indeed,
end_bio_extent_writepage distinguished between whole_page and
non-whole_page writes but behaved identically in both cases!
I've replaced the whole_page computations with warnings, just to be
sure that we're not issuing partial page reads or writes. The
warnings should probably just go away some time.
Signed-off-by: Alexandre Oliva <oliva@gnu.org>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
lock_extent/unlock_extent expect an exclusive end.
Tested-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs update from Chris Mason:
"These are mostly fixes. The biggest exceptions are Josef's skinny
extents and Jan Schmidt's code to rebuild our quota indexes if they
get out of sync (or you enable quotas on an existing filesystem).
The skinny extents are off by default because they are a new variation
on the extent allocation tree format. btrfstune -x enables them, and
the new format makes the extent allocation tree about 30% smaller.
I rebased this a few days ago to rework Dave Sterba's crc checks on
the super block, but almost all of these go back to rc6, since I
though 3.9 was due any minute.
The biggest missing fix is the tracepoint bug that was hit late in
3.9. I ran into problems with that in overnight testing and I'm still
tracking it down. I'll definitely have that fixed for rc2."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (101 commits)
Btrfs: allow superblock mismatch from older mkfs
btrfs: enhance superblock checks
btrfs: fix misleading variable name for flags
btrfs: use unsigned long type for extent state bits
Btrfs: improve the loop of scrub_stripe
btrfs: read entire device info under lock
btrfs: remove unused gfp mask parameter from release_extent_buffer callchain
btrfs: handle errors returned from get_tree_block_key
btrfs: make static code static & remove dead code
Btrfs: deal with errors in write_dev_supers
Btrfs: remove almost all of the BUG()'s from tree-log.c
Btrfs: deal with free space cache errors while replaying log
Btrfs: automatic rescan after "quota enable" command
Btrfs: rescan for qgroups
Btrfs: split btrfs_qgroup_account_ref into four functions
Btrfs: allocate new chunks if the space is not enough for global rsv
Btrfs: separate sequence numbers for delayed ref tracking and tree mod log
btrfs: move leak debug code to functions
Btrfs: return free space in cow error path
Btrfs: set UUID in root_item for created trees
...
|
|
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
It's unused since 0b32f4bbb423f02ac.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
Big patch, but all it does is add statics to functions which
are in fact static, then remove the associated dead-code fallout.
removed functions:
btrfs_iref_to_path()
__btrfs_lookup_delayed_deletion_item()
__btrfs_search_delayed_insertion_item()
__btrfs_search_delayed_deletion_item()
find_eb_for_page()
btrfs_find_block_group()
range_straddles_pages()
extent_range_uptodate()
btrfs_file_extent_length()
btrfs_scrub_cancel_devid()
btrfs_start_transaction_lflush()
btrfs_print_tree() is left because it is used for debugging.
btrfs_start_transaction_lflush() and btrfs_reada_detach() are
left for symmetry.
ulist.c functions are left, another patch will take care of those.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
Clean up the leak debugging in extent_io.c by moving
the debug code into functions. This also removes the
list_heads used for debugging from the extent_buffer
and extent_state structures when debug is not enabled.
Since we need a global debug config to do that last
part, implement CONFIG_BTRFS_DEBUG to accommodate.
Thanks to Dave Sterba for the Kconfig bit.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
We can just look up the extent_buffers for the range and free stuff that way.
This makes the cleanup a bit cleaner and we can make sure to evict the
extent_buffers pretty quickly by marking them as stale. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
We need to tag metadata io with REQ_META to avoid priority inversion when using
io throttling cqroups. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
It is very likely that there are several blocks in bio, it is very
inefficient if we get their csums one by one. This patch improves
this problem by getting the csums in batch.
According to the result of the following test, the execute time of
__btrfs_lookup_bio_sums() is down by ~28%(300us -> 217us).
# dd if=<mnt>/file of=/dev/null bs=1M count=1024
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
set_extent_bit()'s (u64 *failed_start) expects NULL not 0.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq into for-3.10/core
Tejun writes:
-----
This is the pull request for the earlier patchset[1] with the same
name. It's only three patches (the first one was committed to
workqueue tree) but the merge strategy is a bit involved due to the
dependencies.
* Because the conversion needs features from wq/for-3.10,
block/for-3.10/core is based on rc3, and wq/for-3.10 has conflicts
with rc3, I pulled mainline (rc5) into wq/for-3.10 to prevent those
workqueue conflicts from flaring up in block tree.
* Resolving the issue that Jan and Dave raised about debugging
requires arch-wide changes. The patchset is being worked on[2] but
it'll have to go through -mm after these changes show up in -next,
and not included in this pull request.
The three commits are located in the following git branch.
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git writeback-workqueue
Pulling it into block/for-3.10/core produces a conflict in
drivers/md/raid5.c between the following two commits.
e3620a3ad5 ("MD RAID5: Avoid accessing gendisk or queue structs when not available")
2f6db2a707 ("raid5: use bio_reset()")
The conflict is trivial - one removes an "if ()" conditional while the
other removes "rbi->bi_next = NULL" right above it. We just need to
remove both. The merged branch is available at
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git block-test-merge
so that you can use it for verification. The test merge commit has
proper merge description.
While these changes are a bit of pain to route, they make code simpler
and even have, while minute, measureable performance gain[3] even on a
workload which isn't particularly favorable to showing the benefits of
this conversion.
----
Fixed up the conflict.
Conflicts:
drivers/md/raid5.c
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Btrfs uses page_mkwrite to ensure stable pages during
crc calculations and mmap workloads. We call clear_page_dirty_for_io
before we do any crcs, and this forces any application with the file
mapped to wait for the crc to finish before it is allowed to change
the file.
With compression on, the clear_page_dirty_for_io step is happening after
we've compressed the pages. This means the applications might be
changing the pages while we are compressing them, and some of those
modifications might not hit the disk.
This commit adds the clear_page_dirty_for_io before compression starts
and makes sure to redirty the page if we have to fallback to
uncompressed IO as well.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Reported-by: Alexandre Oliva <oliva@gnu.org>
cc: stable@vger.kernel.org
|
|
Just a little convenience macro - main reason to add it now is preparing
for immutable bio vecs, it'll reduce the size of the patch that puts
bi_sector/bi_size/bi_idx into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Lars Ellenberg <drbd-dev@lists.linbit.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: linux-s390@vger.kernel.org
CC: Chris Mason <chris.mason@fusionio.com>
CC: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
We want to avoid module.h where posible, since it in turn includes
nearly all of header space. This means removing it where it is not
required, and using export.h where we are only exporting symbols via
EXPORT_SYMBOL and friends.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
The nodesize is capped at 64k and there are enough pages preallocated in
extent_buffer::inline_pages. The fallback to kmalloc never happened
because even on the smallest page size considered (4k) inline_pages
covered the needs.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
Though most of the btrfs codes are using ALIGN macro for page alignment,
there are still some codes using open-coded alignment like the
following:
------
u64 mask = ((u64)root->stripesize - 1);
u64 ret = (val + mask) & ~mask;
------
Or even hidden one:
------
num_bytes = (end - start + blocksize) & ~(blocksize - 1);
------
Sometimes these open-coded alignment is not so easy to understand for
newbie like me.
This commit changes the open-coded alignment to the ALIGN macro for a
better readability.
Also there is a previous patch from David Sterba with similar changes,
but the patch is for 3.2 kernel and seems not merged.
http://www.spinics.net/lists/linux-btrfs/msg12747.html
Cc: David Sterba <dave@jikos.cz>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Conflicts:
fs/btrfs/ctree.h
fs/btrfs/extent-tree.c
fs/btrfs/inode.c
fs/btrfs/volumes.c
|
|
Nobody uses these io tree ops anymore so just remove them and clean up the code
a bit. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
->dirty_metadata_bytes is accessed very frequently, so use percpu
counter instead of the u64 variant to reduce the contention of
the lock.
This patch also fixed the problem that we access it without
lock protection in __btrfs_btree_balance_dirty(), which may
cause we skip the dirty pages flush.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
Use wrapper page_offset to get byte-offset into filesystem object for page.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
The extent buffers have a refs_lock which we use to make coordinate freeing
the extent buffer with operations on the radix tree. On tree roots and
other extent buffers that very cache hot, this can be highly contended.
These are also the extent buffers that are basically pinned in memory.
This commit adds code to cmpxchg our way through the ref modifications,
and as long as the result of the reference change is still pinned in
ram, we skip the expensive spinlock.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
This builds on David Woodhouse's original Btrfs raid5/6 implementation.
The code has changed quite a bit, blame Chris Mason for any bugs.
Read/modify/write is done after the higher levels of the filesystem have
prepared a given bio. This means the higher layers are not responsible
for building full stripes, and they don't need to query for the topology
of the extents that may get allocated during delayed allocation runs.
It also means different files can easily share the same stripe.
But, it does expose us to incorrect parity if we crash or lose power
while doing a read/modify/write cycle. This will be addressed in a
later commit.
Scrub is unable to repair crc errors on raid5/6 chunks.
Discard does not work on raid5/6 (yet)
The stripe size is fixed at 64KiB per disk. This will be tunable
in a later commit.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
We'll want to merge writes so they can fill a full RAID[56] stripe, but
not necessarily reads.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
With the addition of the device replace procedure, it is possible
for btrfs_map_bio(READ) to report an error. This happens when the
specific mirror is requested which is located on the target disk,
and the copy operation has not yet copied this block. Hence the
block cannot be read and this error state is indicated by
returning EIO.
Some background information follows now. A new mirror is added
while the device replace procedure is running.
btrfs_get_num_copies() returns one more, and
btrfs_map_bio(GET_READ_MIRROR) adds one more mirror if a disk
location is involved that was already handled by the device
replace copy operation. The assigned mirror num is the highest
mirror number, e.g. the value 3 in case of RAID1.
If btrfs_map_bio() is invoked with mirror_num == 0 (i.e., select
any mirror), the copy on the target drive is never selected
because that disk shall be able to perform the write requests as
quickly as possible. The parallel execution of read requests would
only slow down the disk copy procedure. Second case is that
btrfs_map_bio() is called with mirror_num > 0. This is done from
the repair code only. In this case, the highest mirror num is
assigned to the target disk, since it is used last. And when this
mirror is not available because the copy procedure has not yet
handled this area, an error is returned. Everywhere in the code
the handling of such errors is added now.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
|
This is required for the device replace procedure in a later step.
Two calling functions also had to be changed to have the fs_info
pointer: repair_io_failure() and scrub_setup_recheck_block().
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
|
