Age | Commit message (Collapse) | Author |
|
commit 678886bdc6378c1cbd5072da2c5a3035000214e3 upstream.
When we abort a transaction we iterate over all the ranges marked as dirty
in fs_info->freed_extents[0] and fs_info->freed_extents[1], clear them
from those trees, add them back (unpin) to the free space caches and, if
the fs was mounted with "-o discard", perform a discard on those regions.
Also, after adding the regions to the free space caches, a fitrim ioctl call
can see those ranges in a block group's free space cache and perform a discard
on the ranges, so the same issue can happen without "-o discard" as well.
This causes corruption, affecting one or multiple btree nodes (in the worst
case leaving the fs unmountable) because some of those ranges (the ones in
the fs_info->pinned_extents tree) correspond to btree nodes/leafs that are
referred by the last committed super block - breaking the rule that anything
that was committed by a transaction is untouched until the next transaction
commits successfully.
I ran into this while running in a loop (for several hours) the fstest that
I recently submitted:
[PATCH] fstests: add btrfs test to stress chunk allocation/removal and fstrim
The corruption always happened when a transaction aborted and then fsck complained
like this:
_check_btrfs_filesystem: filesystem on /dev/sdc is inconsistent
*** fsck.btrfs output ***
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
Check tree block failed, want=94945280, have=0
read block failed check_tree_block
Couldn't open file system
In this case 94945280 corresponded to the root of a tree.
Using frace what I observed was the following sequence of steps happened:
1) transaction N started, fs_info->pinned_extents pointed to
fs_info->freed_extents[0];
2) node/eb 94945280 is created;
3) eb is persisted to disk;
4) transaction N commit starts, fs_info->pinned_extents now points to
fs_info->freed_extents[1], and transaction N completes;
5) transaction N + 1 starts;
6) eb is COWed, and btrfs_free_tree_block() called for this eb;
7) eb range (94945280 to 94945280 + 16Kb) is added to
fs_info->pinned_extents (fs_info->freed_extents[1]);
8) Something goes wrong in transaction N + 1, like hitting ENOSPC
for example, and the transaction is aborted, turning the fs into
readonly mode. The stack trace I got for example:
[112065.253935] [<ffffffff8140c7b6>] dump_stack+0x4d/0x66
[112065.254271] [<ffffffff81042984>] warn_slowpath_common+0x7f/0x98
[112065.254567] [<ffffffffa0325990>] ? __btrfs_abort_transaction+0x50/0x10b [btrfs]
[112065.261674] [<ffffffff810429e5>] warn_slowpath_fmt+0x48/0x50
[112065.261922] [<ffffffffa032949e>] ? btrfs_free_path+0x26/0x29 [btrfs]
[112065.262211] [<ffffffffa0325990>] __btrfs_abort_transaction+0x50/0x10b [btrfs]
[112065.262545] [<ffffffffa036b1d6>] btrfs_remove_chunk+0x537/0x58b [btrfs]
[112065.262771] [<ffffffffa033840f>] btrfs_delete_unused_bgs+0x1de/0x21b [btrfs]
[112065.263105] [<ffffffffa0343106>] cleaner_kthread+0x100/0x12f [btrfs]
(...)
[112065.264493] ---[ end trace dd7903a975a31a08 ]---
[112065.264673] BTRFS: error (device sdc) in btrfs_remove_chunk:2625: errno=-28 No space left
[112065.264997] BTRFS info (device sdc): forced readonly
9) The clear kthread sees that the BTRFS_FS_STATE_ERROR bit is set in
fs_info->fs_state and calls btrfs_cleanup_transaction(), which in
turn calls btrfs_destroy_pinned_extent();
10) Then btrfs_destroy_pinned_extent() iterates over all the ranges
marked as dirty in fs_info->freed_extents[], and for each one
it calls discard, if the fs was mounted with "-o discard", and
adds the range to the free space cache of the respective block
group;
11) btrfs_trim_block_group(), invoked from the fitrim ioctl code path,
sees the free space entries and performs a discard;
12) After an umount and mount (or fsck), our eb's location on disk was full
of zeroes, and it should have been untouched, because it was marked as
dirty in the fs_info->pinned_extents tree, and therefore used by the
trees that the last committed superblock points to.
Fix this by not performing a discard and not adding the ranges to the free space
caches - it's useless from this point since the fs is now in readonly mode and
we won't write free space caches to disk anymore (otherwise we would leak space)
nor any new superblock. By not adding the ranges to the free space caches, it
prevents other code paths from allocating that space and write to it as well,
therefore being safer and simpler.
This isn't a new problem, as it's been present since 2011 (git commit
acce952b0263825da32cf10489413dec78053347).
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a28046956c71985046474283fa3bcd256915fb72 upstream.
We use the modified list to keep track of which extents have been modified so we
know which ones are candidates for logging at fsync() time. Newly modified
extents are added to the list at modification time, around the same time the
ordered extent is created. We do this so that we don't have to wait for ordered
extents to complete before we know what we need to log. The problem is when
something like this happens
log extent 0-4k on inode 1
copy csum for 0-4k from ordered extent into log
sync log
commit transaction
log some other extent on inode 1
ordered extent for 0-4k completes and adds itself onto modified list again
log changed extents
see ordered extent for 0-4k has already been logged
at this point we assume the csum has been copied
sync log
crash
On replay we will see the extent 0-4k in the log, drop the original 0-4k extent
which is the same one that we are replaying which also drops the csum, and then
we won't find the csum in the log for that bytenr. This of course causes us to
have errors about not having csums for certain ranges of our inode. So remove
the modified list manipulation in unpin_extent_cache, any modified extents
should have been added well before now, and we don't want them re-logged. This
fixes my test that I could reliably reproduce this problem with. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e8c2af96e0d2d5fe298dd796fb6bc16e888a48d upstream.
... it does that itself (via kmap_atomic())
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0cd6144aadd2afd19d1aca880153530c52957604 upstream.
shmem mappings already contain exceptional entries where swap slot
information is remembered.
To be able to store eviction information for regular page cache, prepare
every site dealing with the radix trees directly to handle entries other
than pages.
The common lookup functions will filter out non-page entries and return
NULL for page cache holes, just as before. But provide a raw version of
the API which returns non-page entries as well, and switch shmem over to
use it.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jan Kara <jack@suse.cz>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Luigi Semenzato <semenzato@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Metin Doslu <metin@citusdata.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Ozgun Erdogan <ozgun@citusdata.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roman Gushchin <klamm@yandex-team.ru>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6e5aafb27419f32575b27ef9d6a31e5d54661aca upstream.
If we hit any errors in btrfs_lookup_csums_range, we'll loop through all
the csums we allocate and free them. But the code was using list_entry
incorrectly, and ended up trying to free the on-stack list_head instead.
This bug came from commit 0678b6185
btrfs: Don't BUG_ON kzalloc error in btrfs_lookup_csums_range()
Signed-off-by: Chris Mason <clm@fb.com>
Reported-by: Erik Berg <btrfs@slipsprogrammoer.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 766b5e5ae78dd04a93a275690a49e23d7dcb1f39 upstream.
During an incremental send, when we finish processing an inode (corresponding to
a regular file) we would assume the gap between the end of the last processed file
extent and the file's size corresponded to a file hole, and therefore incorrectly
send a bunch of zero bytes to overwrite that region in the file.
This affects only kernel 3.14.
Reproducer:
mkfs.btrfs -f /dev/sdc
mount /dev/sdc /mnt
xfs_io -f -c "falloc -k 0 268435456" /mnt/foo
btrfs subvolume snapshot -r /mnt /mnt/mysnap0
xfs_io -c "pwrite -S 0x01 -b 9216 16190218 9216" /mnt/foo
xfs_io -c "pwrite -S 0x02 -b 1121 198720104 1121" /mnt/foo
xfs_io -c "pwrite -S 0x05 -b 9216 107887439 9216" /mnt/foo
xfs_io -c "pwrite -S 0x06 -b 9216 225520207 9216" /mnt/foo
xfs_io -c "pwrite -S 0x07 -b 67584 102138300 67584" /mnt/foo
xfs_io -c "pwrite -S 0x08 -b 7000 94897484 7000" /mnt/foo
xfs_io -c "pwrite -S 0x09 -b 113664 245083212 113664" /mnt/foo
xfs_io -c "pwrite -S 0x10 -b 123 17937788 123" /mnt/foo
xfs_io -c "pwrite -S 0x11 -b 39936 229573311 39936" /mnt/foo
xfs_io -c "pwrite -S 0x12 -b 67584 174792222 67584" /mnt/foo
xfs_io -c "pwrite -S 0x13 -b 9216 249253213 9216" /mnt/foo
xfs_io -c "pwrite -S 0x16 -b 67584 150046083 67584" /mnt/foo
xfs_io -c "pwrite -S 0x17 -b 39936 118246040 39936" /mnt/foo
xfs_io -c "pwrite -S 0x18 -b 67584 215965442 67584" /mnt/foo
xfs_io -c "pwrite -S 0x19 -b 33792 97096725 33792" /mnt/foo
xfs_io -c "pwrite -S 0x20 -b 125952 166300596 125952" /mnt/foo
xfs_io -c "pwrite -S 0x21 -b 123 1078957 123" /mnt/foo
xfs_io -c "pwrite -S 0x25 -b 9216 212044492 9216" /mnt/foo
xfs_io -c "pwrite -S 0x26 -b 7000 265037146 7000" /mnt/foo
xfs_io -c "pwrite -S 0x27 -b 42757 215922685 42757" /mnt/foo
xfs_io -c "pwrite -S 0x28 -b 7000 69865411 7000" /mnt/foo
xfs_io -c "pwrite -S 0x29 -b 67584 67948958 67584" /mnt/foo
xfs_io -c "pwrite -S 0x30 -b 39936 266967019 39936" /mnt/foo
xfs_io -c "pwrite -S 0x31 -b 1121 19582453 1121" /mnt/foo
xfs_io -c "pwrite -S 0x32 -b 17408 257710255 17408" /mnt/foo
xfs_io -c "pwrite -S 0x33 -b 39936 3895518 39936" /mnt/foo
xfs_io -c "pwrite -S 0x34 -b 125952 12045847 125952" /mnt/foo
xfs_io -c "pwrite -S 0x35 -b 17408 19156379 17408" /mnt/foo
xfs_io -c "pwrite -S 0x36 -b 39936 50160066 39936" /mnt/foo
xfs_io -c "pwrite -S 0x37 -b 113664 9549793 113664" /mnt/foo
xfs_io -c "pwrite -S 0x38 -b 105472 94391506 105472" /mnt/foo
xfs_io -c "pwrite -S 0x39 -b 23552 143632863 23552" /mnt/foo
xfs_io -c "pwrite -S 0x40 -b 39936 241283845 39936" /mnt/foo
xfs_io -c "pwrite -S 0x41 -b 113664 199937606 113664" /mnt/foo
xfs_io -c "pwrite -S 0x42 -b 67584 67380093 67584" /mnt/foo
xfs_io -c "pwrite -S 0x43 -b 67584 26793129 67584" /mnt/foo
xfs_io -c "pwrite -S 0x44 -b 39936 14421913 39936" /mnt/foo
xfs_io -c "pwrite -S 0x45 -b 123 253097405 123" /mnt/foo
xfs_io -c "pwrite -S 0x46 -b 1121 128233424 1121" /mnt/foo
xfs_io -c "pwrite -S 0x47 -b 105472 91577959 105472" /mnt/foo
xfs_io -c "pwrite -S 0x48 -b 1121 7245381 1121" /mnt/foo
xfs_io -c "pwrite -S 0x49 -b 113664 182414694 113664" /mnt/foo
xfs_io -c "pwrite -S 0x50 -b 9216 32750608 9216" /mnt/foo
xfs_io -c "pwrite -S 0x51 -b 67584 266546049 67584" /mnt/foo
xfs_io -c "pwrite -S 0x52 -b 67584 87969398 67584" /mnt/foo
xfs_io -c "pwrite -S 0x53 -b 9216 260848797 9216" /mnt/foo
xfs_io -c "pwrite -S 0x54 -b 39936 119461243 39936" /mnt/foo
xfs_io -c "pwrite -S 0x55 -b 7000 200178693 7000" /mnt/foo
xfs_io -c "pwrite -S 0x56 -b 9216 243316029 9216" /mnt/foo
xfs_io -c "pwrite -S 0x57 -b 7000 209658229 7000" /mnt/foo
xfs_io -c "pwrite -S 0x58 -b 101376 179745192 101376" /mnt/foo
xfs_io -c "pwrite -S 0x59 -b 9216 64012300 9216" /mnt/foo
xfs_io -c "pwrite -S 0x60 -b 125952 181705139 125952" /mnt/foo
xfs_io -c "pwrite -S 0x61 -b 23552 235737348 23552" /mnt/foo
xfs_io -c "pwrite -S 0x62 -b 113664 106021355 113664" /mnt/foo
xfs_io -c "pwrite -S 0x63 -b 67584 135753552 67584" /mnt/foo
xfs_io -c "pwrite -S 0x64 -b 23552 95730888 23552" /mnt/foo
xfs_io -c "pwrite -S 0x65 -b 11 17311415 11" /mnt/foo
xfs_io -c "pwrite -S 0x66 -b 33792 120695553 33792" /mnt/foo
xfs_io -c "pwrite -S 0x67 -b 9216 17164631 9216" /mnt/foo
xfs_io -c "pwrite -S 0x68 -b 9216 136065853 9216" /mnt/foo
xfs_io -c "pwrite -S 0x69 -b 67584 37752198 67584" /mnt/foo
xfs_io -c "pwrite -S 0x70 -b 101376 189717473 101376" /mnt/foo
xfs_io -c "pwrite -S 0x71 -b 7000 227463698 7000" /mnt/foo
xfs_io -c "pwrite -S 0x72 -b 9216 12655137 9216" /mnt/foo
xfs_io -c "pwrite -S 0x73 -b 7000 7488866 7000" /mnt/foo
xfs_io -c "pwrite -S 0x74 -b 113664 87813649 113664" /mnt/foo
xfs_io -c "pwrite -S 0x75 -b 33792 25802183 33792" /mnt/foo
xfs_io -c "pwrite -S 0x76 -b 39936 93524024 39936" /mnt/foo
xfs_io -c "pwrite -S 0x77 -b 33792 113336388 33792" /mnt/foo
xfs_io -c "pwrite -S 0x78 -b 105472 184955320 105472" /mnt/foo
xfs_io -c "pwrite -S 0x79 -b 101376 225691598 101376" /mnt/foo
xfs_io -c "pwrite -S 0x80 -b 23552 77023155 23552" /mnt/foo
xfs_io -c "pwrite -S 0x81 -b 11 201888192 11" /mnt/foo
xfs_io -c "pwrite -S 0x82 -b 11 115332492 11" /mnt/foo
xfs_io -c "pwrite -S 0x83 -b 67584 230278015 67584" /mnt/foo
xfs_io -c "pwrite -S 0x84 -b 11 120589073 11" /mnt/foo
xfs_io -c "pwrite -S 0x85 -b 125952 202207819 125952" /mnt/foo
xfs_io -c "pwrite -S 0x86 -b 113664 86672080 113664" /mnt/foo
xfs_io -c "pwrite -S 0x87 -b 17408 208459603 17408" /mnt/foo
xfs_io -c "pwrite -S 0x88 -b 7000 73372211 7000" /mnt/foo
xfs_io -c "pwrite -S 0x89 -b 7000 42252122 7000" /mnt/foo
xfs_io -c "pwrite -S 0x90 -b 23552 46784881 23552" /mnt/foo
xfs_io -c "pwrite -S 0x91 -b 101376 63172351 101376" /mnt/foo
xfs_io -c "pwrite -S 0x92 -b 23552 59341931 23552" /mnt/foo
xfs_io -c "pwrite -S 0x93 -b 39936 239599283 39936" /mnt/foo
xfs_io -c "pwrite -S 0x94 -b 67584 175643105 67584" /mnt/foo
xfs_io -c "pwrite -S 0x97 -b 23552 105534880 23552" /mnt/foo
xfs_io -c "pwrite -S 0x98 -b 113664 8236844 113664" /mnt/foo
xfs_io -c "pwrite -S 0x99 -b 125952 144489686 125952" /mnt/foo
xfs_io -c "pwrite -S 0xa0 -b 7000 73273112 7000" /mnt/foo
xfs_io -c "pwrite -S 0xa1 -b 125952 194580243 125952" /mnt/foo
xfs_io -c "pwrite -S 0xa2 -b 123 56296779 123" /mnt/foo
xfs_io -c "pwrite -S 0xa3 -b 11 233066845 11" /mnt/foo
xfs_io -c "pwrite -S 0xa4 -b 39936 197727090 39936" /mnt/foo
xfs_io -c "pwrite -S 0xa5 -b 101376 53579812 101376" /mnt/foo
xfs_io -c "pwrite -S 0xa6 -b 9216 85669738 9216" /mnt/foo
xfs_io -c "pwrite -S 0xa7 -b 125952 21266322 125952" /mnt/foo
xfs_io -c "pwrite -S 0xa8 -b 23552 125726568 23552" /mnt/foo
xfs_io -c "pwrite -S 0xa9 -b 9216 18423680 9216" /mnt/foo
xfs_io -c "pwrite -S 0xb0 -b 1121 165901483 1121" /mnt/foo
btrfs subvolume snapshot -r /mnt /mnt/mysnap1
xfs_io -c "pwrite -S 0xff -b 10 16190218 10" /mnt/foo
btrfs subvolume snapshot -r /mnt /mnt/mysnap2
md5sum /mnt/foo # returns 79e53f1466bfc09fd82b450689e6119e
md5sum /mnt/mysnap2/foo # returns 79e53f1466bfc09fd82b450689e6119e too
btrfs send /mnt/mysnap1 -f /tmp/1.snap
btrfs send -p /mnt/mysnap1 /mnt/mysnap2 -f /tmp/2.snap
mkfs.btrfs -f /dev/sdc
mount /dev/sdc /mnt
btrfs receive /mnt -f /tmp/1.snap
btrfs receive /mnt -f /tmp/2.snap
md5sum /mnt/mysnap2/foo # returns 2bb414c5155767cedccd7063e51beabd !!
A testcase for xfstests follows soon too.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 42383020beb1cfb05f5d330cc311931bc4917a97 upstream.
We check whether transid is already committed via last_trans_committed and
then search through trans_list for pending transactions. If
last_trans_committed is updated by btrfs_commit_transaction after we check
it (there is no locking), we will fail to find the committed transaction
and return EINVAL to the caller. This has been observed occasionally by
ceph-osd (which uses this ioctl heavily).
Fix by rechecking whether the provided transid <= last_trans_committed
after the search fails, and if so return 0.
Signed-off-by: Sage Weil <sage@redhat.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bbe9051441effce51c9a533d2c56440df64db2d7 upstream.
Marc Merlin sent me a broken fs image months ago where it would blow up in the
upper->checked BUG_ON() in build_backref_tree. This is because we had a
scenario like this
block a -- level 4 (not shared)
|
block b -- level 3 (reloc block, shared)
|
block c -- level 2 (not shared)
|
block d -- level 1 (shared)
|
block e -- level 0 (shared)
We go to build a backref tree for block e, we notice block d is shared and add
it to the list of blocks to lookup it's backrefs for. Now when we loop around
we will check edges for the block, so we will see we looked up block c last
time. So we lookup block d and then see that the block that points to it is
block c and we can just skip that edge since we've already been up this path.
The problem is because we clear need_check when we see block d (as it is shared)
we never add block b as needing to be checked. And because block c is in our
path already we bail out before we walk up to block b and add it to the backref
check list.
To fix this we need to reset need_check if we trip over a block that doesn't
need to be checked. This will make sure that any subsequent blocks in the path
as we're walking up afterwards are added to the list to be processed. With this
patch I can now mount Marc's fs image and it'll complete the balance without
panicing. Thanks,
Reported-by: Marc MERLIN <marc@merlins.org>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 75bfb9aff45e44625260f52a5fd581b92ace3e62 upstream.
When balance panics it tends to panic in the
BUG_ON(!upper->checked);
test, because it means it couldn't build the backref tree properly. This is
annoying to users and frankly a recoverable error, nothing in this function is
actually fatal since it is just an in-memory building of the backrefs for a
given bytenr. So go through and change all the BUG_ON()'s to ASSERT()'s, and
fix the BUG_ON(!upper->checked) thing to just return an error.
This patch also fixes the error handling so it tears down the work we've done
properly. This code was horribly broken since we always just panic'ed instead
of actually erroring out, so it needed to be completely re-worked. With this
patch my broken image no longer panics when I mount it. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d52c78afbbf80b58299e076a159617d6b42fe3c upstream.
When doing log replay we may have to update inodes, which traditionally goes
through our delayed inode stuff. This will try to move space over from the
trans handle, but we don't reserve space in our trans handle on replay since we
don't know how much we will need, so instead we try to flush. But because we
have a trans handle open we won't flush anything, so if we are out of reserve
space we will simply return ENOSPC. Since we know that if an operation made it
into the log then we definitely had space before the box bought the farm then we
don't need to worry about doing this space reservation. Use the
fs_info->log_root_recovering flag to skip the delayed inode stuff and update the
item directly. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d1a40c66bed0b3fa43b9da5fbd5cbe332e4eccf upstream.
An user reported this, it is because that lseek's SEEK_SET/SEEK_CUR/SEEK_END
allow a negative value for @offset, but btrfs's SEEK_DATA/SEEK_HOLE don't
prepare for that and convert the negative @offset into unsigned type,
so we get (end < start) warning.
[ 1269.835374] ------------[ cut here ]------------
[ 1269.836809] WARNING: CPU: 0 PID: 1241 at fs/btrfs/extent_io.c:430 insert_state+0x11d/0x140()
[ 1269.838816] BTRFS: end < start 4094 18446744073709551615
[ 1269.840334] CPU: 0 PID: 1241 Comm: a.out Tainted: G W 3.16.0+ #306
[ 1269.858229] Call Trace:
[ 1269.858612] [<ffffffff81801a69>] dump_stack+0x4e/0x68
[ 1269.858952] [<ffffffff8107894c>] warn_slowpath_common+0x8c/0xc0
[ 1269.859416] [<ffffffff81078a36>] warn_slowpath_fmt+0x46/0x50
[ 1269.859929] [<ffffffff813b0fbd>] insert_state+0x11d/0x140
[ 1269.860409] [<ffffffff813b1396>] __set_extent_bit+0x3b6/0x4e0
[ 1269.860805] [<ffffffff813b21c7>] lock_extent_bits+0x87/0x200
[ 1269.861697] [<ffffffff813a5b28>] btrfs_file_llseek+0x148/0x2a0
[ 1269.862168] [<ffffffff811f201e>] SyS_lseek+0xae/0xc0
[ 1269.862620] [<ffffffff8180b212>] system_call_fastpath+0x16/0x1b
[ 1269.862970] ---[ end trace 4d33ea885832054b ]---
This assumes that btrfs starts finding DATA/HOLE from the beginning of file
if the assigned @offset is negative.
Also we add alignment for lock_extent_bits 's range.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78a017a2c92df9b571db0a55a016280f9019c65e upstream.
The behaviour of a 'chattr -c' consists of getting the current flags,
clearing the FS_COMPR_FL bit and then sending the result to the set
flags ioctl - this means the bit FS_NOCOMP_FL isn't set in the flags
passed to the ioctl. This results in the compression property not being
cleared from the inode - it was cleared only if the bit FS_NOCOMP_FL
was set in the received flags.
Reproducer:
$ mkfs.btrfs -f /dev/sdd
$ mount /dev/sdd /mnt && cd /mnt
$ mkdir a
$ chattr +c a
$ touch a/file
$ lsattr a/file
--------c------- a/file
$ chattr -c a
$ touch a/file2
$ lsattr a/file2
--------c------- a/file2
$ lsattr -d a
---------------- a
Reported-by: Andreas Schneider <asn@cryptomilk.org>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2fad4e83e12591eb3bd213875b9edc2d18e93383 upstream.
The transaction thread may want to do more work, namely it pokes the
cleaner ktread that will start processing uncleaned subvols.
This can be triggered by user via the 'btrfs fi sync' command, otherwise
there was a delay up to 30 seconds before the cleaner started to clean
old snapshots.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 38c1c2e44bacb37efd68b90b3f70386a8ee370ee upstream.
The crash is
------------[ cut here ]------------
kernel BUG at fs/btrfs/extent_io.c:2124!
[...]
Workqueue: btrfs-endio normal_work_helper [btrfs]
RIP: 0010:[<ffffffffa02d6055>] [<ffffffffa02d6055>] end_bio_extent_readpage+0xb45/0xcd0 [btrfs]
This is in fact a regression.
It is because we forgot to increase @offset properly in reading corrupted block,
so that the @offset remains, and this leads to checksum errors while reading
left blocks queued up in the same bio, and then ends up with hiting the above
BUG_ON.
Reported-by: Chris Murphy <lists@colorremedies.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce62003f690dff38d3164a632ec69efa15c32cbf upstream.
When failing to allocate space for the whole compressed extent, we'll
fallback to uncompressed IO, but we've forgotten to redirty the pages
which belong to this compressed extent, and these 'clean' pages will
simply skip 'submit' part and go to endio directly, at last we got data
corruption as we write nothing.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Tested-By: Martin Steigerwald <martin@lichtvoll.de>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f7ff6d7832c6be13e8c95598884dbc40ad69fb7 upstream.
Before processing the extent buffer, acquire a read lock on it, so
that we're safe against concurrent updates on the extent buffer.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 27b9a8122ff71a8cadfbffb9c4f0694300464f3b upstream.
Under rare circumstances we can end up leaving 2 versions of a checksum
for the same file extent range.
The reason for this is that after calling btrfs_next_leaf we process
slot 0 of the leaf it returns, instead of processing the slot set in
path->slots[0]. Most of the time (by far) path->slots[0] is 0, but after
btrfs_next_leaf() releases the path and before it searches for the next
leaf, another task might cause a split of the next leaf, which migrates
some of its keys to the leaf we were processing before calling
btrfs_next_leaf(). In this case btrfs_next_leaf() returns again the
same leaf but with path->slots[0] having a slot number corresponding
to the first new key it got, that is, a slot number that didn't exist
before calling btrfs_next_leaf(), as the leaf now has more keys than
it had before. So we must really process the returned leaf starting at
path->slots[0] always, as it isn't always 0, and the key at slot 0 can
have an offset much lower than our search offset/bytenr.
For example, consider the following scenario, where we have:
sums->bytenr: 40157184, sums->len: 16384, sums end: 40173568
four 4kb file data blocks with offsets 40157184, 40161280, 40165376, 40169472
Leaf N:
slot = 0 slot = btrfs_header_nritems() - 1
|-------------------------------------------------------------------|
| [(CSUM CSUM 39239680), size 8] ... [(CSUM CSUM 40116224), size 4] |
|-------------------------------------------------------------------|
Leaf N + 1:
slot = 0 slot = btrfs_header_nritems() - 1
|--------------------------------------------------------------------|
| [(CSUM CSUM 40161280), size 32] ... [((CSUM CSUM 40615936), size 8 |
|--------------------------------------------------------------------|
Because we are at the last slot of leaf N, we call btrfs_next_leaf() to
find the next highest key, which releases the current path and then searches
for that next key. However after releasing the path and before finding that
next key, the item at slot 0 of leaf N + 1 gets moved to leaf N, due to a call
to ctree.c:push_leaf_left() (via ctree.c:split_leaf()), and therefore
btrfs_next_leaf() will returns us a path again with leaf N but with the slot
pointing to its new last key (CSUM CSUM 40161280). This new version of leaf N
is then:
slot = 0 slot = btrfs_header_nritems() - 2 slot = btrfs_header_nritems() - 1
|----------------------------------------------------------------------------------------------------|
| [(CSUM CSUM 39239680), size 8] ... [(CSUM CSUM 40116224), size 4] [(CSUM CSUM 40161280), size 32] |
|----------------------------------------------------------------------------------------------------|
And incorrecly using slot 0, makes us set next_offset to 39239680 and we jump
into the "insert:" label, which will set tmp to:
tmp = min((sums->len - total_bytes) >> blocksize_bits,
(next_offset - file_key.offset) >> blocksize_bits) =
min((16384 - 0) >> 12, (39239680 - 40157184) >> 12) =
min(4, (u64)-917504 = 18446744073708634112 >> 12) = 4
and
ins_size = csum_size * tmp = 4 * 4 = 16 bytes.
In other words, we insert a new csum item in the tree with key
(CSUM_OBJECTID CSUM_KEY 40157184 = sums->bytenr) that contains the checksums
for all the data (4 blocks of 4096 bytes each = sums->len). Which is wrong,
because the item with key (CSUM CSUM 40161280) (the one that was moved from
leaf N + 1 to the end of leaf N) contains the old checksums of the last 12288
bytes of our data and won't get those old checksums removed.
So this leaves us 2 different checksums for 3 4kb blocks of data in the tree,
and breaks the logical rule:
Key_N+1.offset >= Key_N.offset + length_of_data_its_checksums_cover
An obvious bad effect of this is that a subsequent csum tree lookup to get
the checksum of any of the blocks with logical offset of 40161280, 40165376
or 40169472 (the last 3 4kb blocks of file data), will get the old checksums.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4eb1f66dce6c4dc28dd90a7ffbe6b2b1cb08aa4e upstream.
We've got bug reports that btrfs crashes when quota is enabled on
32bit kernel, typically with the Oops like below:
BUG: unable to handle kernel NULL pointer dereference at 00000004
IP: [<f9234590>] find_parent_nodes+0x360/0x1380 [btrfs]
*pde = 00000000
Oops: 0000 [#1] SMP
CPU: 0 PID: 151 Comm: kworker/u8:2 Tainted: G S W 3.15.2-1.gd43d97e-default #1
Workqueue: btrfs-qgroup-rescan normal_work_helper [btrfs]
task: f1478130 ti: f147c000 task.ti: f147c000
EIP: 0060:[<f9234590>] EFLAGS: 00010213 CPU: 0
EIP is at find_parent_nodes+0x360/0x1380 [btrfs]
EAX: f147dda8 EBX: f147ddb0 ECX: 00000011 EDX: 00000000
ESI: 00000000 EDI: f147dda4 EBP: f147ddf8 ESP: f147dd38
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 00000004 CR3: 00bf3000 CR4: 00000690
Stack:
00000000 00000000 f147dda4 00000050 00000001 00000000 00000001 00000050
00000001 00000000 d3059000 00000001 00000022 000000a8 00000000 00000000
00000000 000000a1 00000000 00000000 00000001 00000000 00000000 11800000
Call Trace:
[<f923564d>] __btrfs_find_all_roots+0x9d/0xf0 [btrfs]
[<f9237bb1>] btrfs_qgroup_rescan_worker+0x401/0x760 [btrfs]
[<f9206148>] normal_work_helper+0xc8/0x270 [btrfs]
[<c025e38b>] process_one_work+0x11b/0x390
[<c025eea1>] worker_thread+0x101/0x340
[<c026432b>] kthread+0x9b/0xb0
[<c0712a71>] ret_from_kernel_thread+0x21/0x30
[<c0264290>] kthread_create_on_node+0x110/0x110
This indicates a NULL corruption in prefs_delayed list. The further
investigation and bisection pointed that the call of ulist_add_merge()
results in the corruption.
ulist_add_merge() takes u64 as aux and writes a 64bit value into
old_aux. The callers of this function in backref.c, however, pass a
pointer of a pointer to old_aux. That is, the function overwrites
64bit value on 32bit pointer. This caused a NULL in the adjacent
variable, in this case, prefs_delayed.
Here is a quick attempt to band-aid over this: a new function,
ulist_add_merge_ptr() is introduced to pass/store properly a pointer
value instead of u64. There are still ugly void ** cast remaining
in the callers because void ** cannot be taken implicitly. But, it's
safer than explicit cast to u64, anyway.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=887046
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1895442be01c58449e3bf9272f22062a670e08f upstream.
We are currently allocating space_info objects in an array when we
allocate space_info. When a user does something like:
# btrfs balance start -mconvert=raid1 -dconvert=raid1 /mnt
# btrfs balance start -mconvert=single -dconvert=single /mnt -f
# btrfs balance start -mconvert=raid1 -dconvert=raid1 /
We can end up with memory corruption since the kobject hasn't
been reinitialized properly and the name pointer was left set.
The rationale behind allocating them statically was to avoid
creating a separate kobject container that just contained the
raid type. It used the index in the array to determine the index.
Ultimately, though, this wastes more memory than it saves in all
but the most complex scenarios and introduces kobject lifetime
questions.
This patch allocates the kobjects dynamically instead. Note that
we also remove the kobject_get/put of the parent kobject since
kobject_add and kobject_del do that internally.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed55b6ac077fe7f9c6490ff55172c4b563562d7c upstream.
When encountering memory pressure, testers have run into the following
lockdep warning. It was caused by __link_block_group calling kobject_add
with the groups_sem held. kobject_add calls kvasprintf with GFP_KERNEL,
which gets us into reclaim context. The kobject doesn't actually need
to be added under the lock -- it just needs to ensure that it's only
added for the first block group to be linked.
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.14.0-rc8-default #1 Not tainted
---------------------------------------------------------
kswapd0/169 just changed the state of lock:
(&delayed_node->mutex){+.+.-.}, at: [<ffffffffa018baea>] __btrfs_release_delayed_node+0x3a/0x200 [btrfs]
but this lock took another, RECLAIM_FS-unsafe lock in the past:
(&found->groups_sem){+++++.}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&found->groups_sem);
local_irq_disable();
lock(&delayed_node->mutex);
lock(&found->groups_sem);
<Interrupt>
lock(&delayed_node->mutex);
*** DEADLOCK ***
2 locks held by kswapd0/169:
#0: (shrinker_rwsem){++++..}, at: [<ffffffff81159e8a>] shrink_slab+0x3a/0x160
#1: (&type->s_umount_key#27){++++..}, at: [<ffffffff811bac6f>] grab_super_passive+0x3f/0x90
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e2426bd0eb980648449e7a2f5a23e3cd3c7725c upstream.
If this condition in end_extent_writepage() is false:
if (tree->ops && tree->ops->writepage_end_io_hook)
we will then test an uninitialized "ret" at:
ret = ret < 0 ? ret : -EIO;
The test for ret is for the case where ->writepage_end_io_hook
failed, and we'd choose that ret as the error; but if
there is no ->writepage_end_io_hook, nothing sets ret.
Initializing ret to 0 should be sufficient; if
writepage_end_io_hook wasn't set, (!uptodate) means
non-zero err was passed in, so we choose -EIO in that case.
Signed-of-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6eda71d0c030af0fc2f68aaa676e6d445600855b upstream.
The skinny extents are intepreted incorrectly in scrub_print_warning(),
and end up hitting the BUG() in btrfs_extent_inline_ref_size.
Reported-by: Konstantinos Skarlatos <k.skarlatos@gmail.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd857dd6bc2ae9ecea14e75a34e8a8fdc158e307 upstream.
We want to make sure the point is still within the extent item, not to verify
the memory it's pointing to.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a56457f5f8fa7c2698ffae8545214c5b96a2cb5 upstream.
The backref code was looking at nodes as well as leaves when we tried to
populate extent item entries. This is not good, and although we go away with it
for the most part because we'd skip where disk_bytenr != random_memory,
sometimes random_memory would match and suddenly boom. This fixes that problem.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8321cf2596d283821acc466377c2b85bcd3422b7 upstream.
There is otherwise a risk of a possible null pointer dereference.
Was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1af56070e3ef9477dbc7eba3b9ad7446979c7974 upstream.
If we are doing an incremental send and the base snapshot has a
directory with name X that doesn't exist anymore in the second
snapshot and a new subvolume/snapshot exists in the second snapshot
that has the same name as the directory (name X), the incremental
send would fail with -ENOENT error. This is because it attempts
to lookup for an inode with a number matching the objectid of a
root, which doesn't exist.
Steps to reproduce:
mkfs.btrfs -f /dev/sdd
mount /dev/sdd /mnt
mkdir /mnt/testdir
btrfs subvolume snapshot -r /mnt /mnt/mysnap1
rmdir /mnt/testdir
btrfs subvolume create /mnt/testdir
btrfs subvolume snapshot -r /mnt /mnt/mysnap2
btrfs send -p /mnt/mysnap1 /mnt/mysnap2 -f /tmp/send.data
A test case for xfstests follows.
Reported-by: Robert White <rwhite@pobox.com>
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 298658414a2f0bea1f05a81876a45c1cd96aa2e0 upstream.
Seeding device support allows us to create a new filesystem
based on existed filesystem.
However newly created filesystem's @total_devices should include seed
devices. This patch fix the following problem:
# mkfs.btrfs -f /dev/sdb
# btrfstune -S 1 /dev/sdb
# mount /dev/sdb /mnt
# btrfs device add -f /dev/sdc /mnt --->fs_devices->total_devices = 1
# umount /mnt
# mount /dev/sdc /mnt --->fs_devices->total_devices = 2
This is because we record right @total_devices in superblock, but
@fs_devices->total_devices is reset to be 0 in btrfs_prepare_sprout().
Fix this problem by not resetting @fs_devices->total_devices.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5dca6eea91653e9949ce6eb9e9acab6277e2f2c4 upstream.
According to commit 865ffef3797da2cac85b3354b5b6050dc9660978
(fs: fix fsync() error reporting),
it's not stable to just check error pages because pages can be
truncated or invalidated, we should also mark mapping with error
flag so that a later fsync can catch the error.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29cc83f69c8338ff8fd1383c9be263d4bdf52d73 upstream.
Same as normal devices, seed devices should be initialized with
fs_info->dev_root as well, otherwise we'll get a NULL pointer crash.
Cc: Chris Murphy <lists@colorremedies.com>
Reported-by: Chris Murphy <lists@colorremedies.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de348ee022175401e77d7662b7ca6e231a94e3fd upstream.
In close_ctree(), after we have stopped all workers,there maybe still
some read requests(for example readahead) to submit and this *maybe* trigger
an oops that user reported before:
kernel BUG at fs/btrfs/async-thread.c:619!
By hacking codes, i can reproduce this problem with one cpu available.
We fix this potential problem by invalidating all btree inode pages before
stopping all workers.
Thanks to Miao for pointing out this problem.
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 32d6b47fe6fc1714d5f1bba1b9f38e0ab0ad58a8 upstream.
If we fail to load a free space cache, we can rebuild it from the extent tree,
so it is not a serious error, we should not output a error message that
would make the users uncomfortable. This patch uses warning message instead
of it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a1972bd9fd4b2fb1bac8b7a0b636d633d8717e3 upstream.
Btrfs will send uevent to udev inform the device change,
but ctime/mtime for the block device inode is not udpated, which cause
libblkid used by btrfs-progs unable to detect device change and use old
cache, causing 'btrfs dev scan; btrfs dev rmove; btrfs dev scan' give an
error message.
Reported-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Cc: Karel Zak <kzak@redhat.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d78874273463a784759916fc3e0b4e2eb141c70 upstream.
We need to NULL the cached_state after freeing it, otherwise
we might free it again if find_delalloc_range doesn't find anything.
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 573a075567f0174551e2fad2a3164afd2af788f2 upstream.
We could have possibly added an extent_op to the locked_ref while we dropped
locked_ref->lock, so check for this case as well and loop around. Otherwise we
could lose flag updates which would lead to extent tree corruption. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3bbb24b20a8800158c33eca8564f432dd14d0bf3 upstream.
Zach found this deadlock that would happen like this
btrfs_end_transaction <- reduce trans->use_count to 0
btrfs_run_delayed_refs
btrfs_cow_block
find_free_extent
btrfs_start_transaction <- increase trans->use_count to 1
allocate chunk
btrfs_end_transaction <- decrease trans->use_count to 0
btrfs_run_delayed_refs
lock tree block we are cowing above ^^
We need to only decrease trans->use_count if it is above 1, otherwise leave it
alone. This will make nested trans be the only ones who decrease their added
ref, and will let us get rid of the trans->use_count++ hack if we have to commit
the transaction. Thanks,
Reported-by: Zach Brown <zab@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Tested-by: Zach Brown <zab@redhat.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f88ba6a2a44ee98e8d59654463dc157bb6d13c43 upstream.
I got an error on v3.13:
BTRFS error (device sdf1) in write_all_supers:3378: errno=-5 IO failure (errors while submitting device barriers.)
how to reproduce:
> mkfs.btrfs -f -d raid1 /dev/sdf1 /dev/sdf2
> wipefs -a /dev/sdf2
> mount -o degraded /dev/sdf1 /mnt
> btrfs balance start -f -sconvert=single -mconvert=single -dconvert=single /mnt
The reason of the error is that barrier_all_devices() failed to submit
barrier to the missing device. However it is clear that we cannot do
anything on missing device, and also it is not necessary to care chunks
on the missing device.
This patch stops sending/waiting barrier if device is missing.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We have a small collection of fixes in my for-linus branch.
The big thing that stands out is a revert of a new ioctl. Users
haven't shipped yet in btrfs-progs, and Dave Sterba found a better way
to export the information"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use right clone root offset for compressed extents
btrfs: fix null pointer deference at btrfs_sysfs_add_one+0x105
Btrfs: unset DCACHE_DISCONNECTED when mounting default subvol
Btrfs: fix max_inline mount option
Btrfs: fix a lockdep warning when cleaning up aborted transaction
Revert "btrfs: add ioctl to export size of global metadata reservation"
|
|
For non compressed extents, iterate_extent_inodes() gives us offsets
that take into account the data offset from the file extent items, while
for compressed extents it doesn't. Therefore we have to adjust them before
placing them in a send clone instruction. Not doing this adjustment leads to
the receiving end requesting for a wrong a file range to the clone ioctl,
which results in different file content from the one in the original send
root.
Issue reproducible with the following excerpt from the test I made for
xfstests:
_scratch_mkfs
_scratch_mount "-o compress-force=lzo"
$XFS_IO_PROG -f -c "truncate 118811" $SCRATCH_MNT/foo
$XFS_IO_PROG -c "pwrite -S 0x0d -b 39987 92267 39987" $SCRATCH_MNT/foo
$BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/mysnap1
$XFS_IO_PROG -c "pwrite -S 0x3e -b 80000 200000 80000" $SCRATCH_MNT/foo
$BTRFS_UTIL_PROG filesystem sync $SCRATCH_MNT
$XFS_IO_PROG -c "pwrite -S 0xdc -b 10000 250000 10000" $SCRATCH_MNT/foo
$XFS_IO_PROG -c "pwrite -S 0xff -b 10000 300000 10000" $SCRATCH_MNT/foo
# will be used for incremental send to be able to issue clone operations
$BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/clones_snap
$BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/mysnap2
$FSSUM_PROG -A -f -w $tmp/1.fssum $SCRATCH_MNT/mysnap1
$FSSUM_PROG -A -f -w $tmp/2.fssum -x $SCRATCH_MNT/mysnap2/mysnap1 \
-x $SCRATCH_MNT/mysnap2/clones_snap $SCRATCH_MNT/mysnap2
$FSSUM_PROG -A -f -w $tmp/clones.fssum $SCRATCH_MNT/clones_snap \
-x $SCRATCH_MNT/clones_snap/mysnap1 -x $SCRATCH_MNT/clones_snap/mysnap2
$BTRFS_UTIL_PROG send $SCRATCH_MNT/mysnap1 -f $tmp/1.snap
$BTRFS_UTIL_PROG send $SCRATCH_MNT/clones_snap -f $tmp/clones.snap
$BTRFS_UTIL_PROG send -p $SCRATCH_MNT/mysnap1 \
-c $SCRATCH_MNT/clones_snap $SCRATCH_MNT/mysnap2 -f $tmp/2.snap
_scratch_unmount
_scratch_mkfs
_scratch_mount
$BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/1.snap
$FSSUM_PROG -r $tmp/1.fssum $SCRATCH_MNT/mysnap1 2>> $seqres.full
$BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/clones.snap
$FSSUM_PROG -r $tmp/clones.fssum $SCRATCH_MNT/clones_snap 2>> $seqres.full
$BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/2.snap
$FSSUM_PROG -r $tmp/2.fssum $SCRATCH_MNT/mysnap2 2>> $seqres.full
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
bdev is null when disk has disappeared and mounted with
the degrade option
stack trace
---------
btrfs_sysfs_add_one+0x105/0x1c0 [btrfs]
open_ctree+0x15f3/0x1fe0 [btrfs]
btrfs_mount+0x5db/0x790 [btrfs]
? alloc_pages_current+0xa4/0x160
mount_fs+0x34/0x1b0
vfs_kern_mount+0x62/0xf0
do_mount+0x22e/0xa80
? __get_free_pages+0x9/0x40
? copy_mount_options+0x31/0x170
SyS_mount+0x7e/0xc0
system_call_fastpath+0x16/0x1b
---------
reproducer:
-------
mkfs.btrfs -draid1 -mraid1 /dev/sdc /dev/sdd
(detach a disk)
devmgt detach /dev/sdc [1]
mount -o degrade /dev/sdd /btrfs
-------
[1] github.com/anajain/devmgt.git
Signed-off-by: Anand Jain <Anand.Jain@oracle.com>
Tested-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
A user was running into errors from an NFS export of a subvolume that had a
default subvol set. When we mount a default subvol we will use d_obtain_alias()
to find an existing dentry for the subvolume in the case that the root subvol
has already been mounted, or a dummy one is allocated in the case that the root
subvol has not already been mounted. This allows us to connect the dentry later
on if we wander into the path. However if we don't ever wander into the path we
will keep DCACHE_DISCONNECTED set for a long time, which angers NFS. It doesn't
appear to cause any problems but it is annoying nonetheless, so simply unset
DCACHE_DISCONNECTED in the get_default_root case and switch btrfs_lookup() to
use d_materialise_unique() instead which will make everything play nicely
together and reconnect stuff if we wander into the defaul subvol path from a
different way. With this patch I'm no longer getting the NFS errors when
exporting a volume that has been mounted with a default subvol set. Thanks,
cc: bfields@fieldses.org
cc: ebiederm@xmission.com
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Currently, the only mount option for max_inline that has any effect is
max_inline=0. Any other value that is supplied to max_inline will be
adjusted to a minimum of 4k. Since max_inline has an effective maximum
of ~3900 bytes due to page size limitations, the current behaviour
only has meaning for max_inline=0.
This patch will allow the the max_inline mount option to accept non-zero
values as indicated in the documentation.
Signed-off-by: Mitch Harder <mitch.harder@sabayonlinux.org>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Given now we have 2 spinlock for management of delayed refs,
CONFIG_DEBUG_SPINLOCK=y helped me find this,
[ 4723.413809] BUG: spinlock wrong CPU on CPU#1, btrfs-transacti/2258
[ 4723.414882] lock: 0xffff880048377670, .magic: dead4ead, .owner: btrfs-transacti/2258, .owner_cpu: 2
[ 4723.417146] CPU: 1 PID: 2258 Comm: btrfs-transacti Tainted: G W O 3.12.0+ #4
[ 4723.421321] Call Trace:
[ 4723.421872] [<ffffffff81680fe7>] dump_stack+0x54/0x74
[ 4723.422753] [<ffffffff81681093>] spin_dump+0x8c/0x91
[ 4723.424979] [<ffffffff816810b9>] spin_bug+0x21/0x26
[ 4723.425846] [<ffffffff81323956>] do_raw_spin_unlock+0x66/0x90
[ 4723.434424] [<ffffffff81689bf7>] _raw_spin_unlock+0x27/0x40
[ 4723.438747] [<ffffffffa015da9e>] btrfs_cleanup_one_transaction+0x35e/0x710 [btrfs]
[ 4723.443321] [<ffffffffa015df54>] btrfs_cleanup_transaction+0x104/0x570 [btrfs]
[ 4723.444692] [<ffffffff810c1b5d>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[ 4723.450336] [<ffffffff810c1c2d>] ? trace_hardirqs_on+0xd/0x10
[ 4723.451332] [<ffffffffa015e5ee>] transaction_kthread+0x22e/0x270 [btrfs]
[ 4723.452543] [<ffffffffa015e3c0>] ? btrfs_cleanup_transaction+0x570/0x570 [btrfs]
[ 4723.457833] [<ffffffff81079efa>] kthread+0xea/0xf0
[ 4723.458990] [<ffffffff81079e10>] ? kthread_create_on_node+0x140/0x140
[ 4723.460133] [<ffffffff81692aac>] ret_from_fork+0x7c/0xb0
[ 4723.460865] [<ffffffff81079e10>] ? kthread_create_on_node+0x140/0x140
[ 4723.496521] ------------[ cut here ]------------
----------------------------------------------------------------------
The reason is that we get to call cond_resched_lock(&head_ref->lock) while
still holding @delayed_refs->lock.
So it's different with __btrfs_run_delayed_refs(), where we do drop-acquire
dance before and after actually processing delayed refs.
Here we don't drop the lock, others are not able to add new delayed refs to
head_ref, so cond_resched_lock(&head_ref->lock) is not necessary here.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
This reverts commit 01e219e8069516cdb98594d417b8bb8d906ed30d.
David Sterba found a different way to provide these features without adding a new
ioctl. We haven't released any progs with this ioctl yet, so I'm taking this out
for now until we finalize things.
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
CC: Jeff Mahoney <jeffm@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix data corruption when reading/updating compressed extents
Btrfs: don't loop forever if we can't run because of the tree mod log
btrfs: reserve no transaction units in btrfs_ioctl_set_features
btrfs: commit transaction after setting label and features
Btrfs: fix assert screwup for the pending move stuff
|
|
When using a mix of compressed file extents and prealloc extents, it
is possible to fill a page of a file with random, garbage data from
some unrelated previous use of the page, instead of a sequence of zeroes.
A simple sequence of steps to get into such case, taken from the test
case I made for xfstests, is:
_scratch_mkfs
_scratch_mount "-o compress-force=lzo"
$XFS_IO_PROG -f -c "pwrite -S 0x06 -b 18670 266978 18670" $SCRATCH_MNT/foobar
$XFS_IO_PROG -c "falloc 26450 665194" $SCRATCH_MNT/foobar
$XFS_IO_PROG -c "truncate 542872" $SCRATCH_MNT/foobar
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foobar
This results in the following file items in the fs tree:
item 4 key (257 INODE_ITEM 0) itemoff 15879 itemsize 160
inode generation 6 transid 6 size 542872 block group 0 mode 100600
item 5 key (257 INODE_REF 256) itemoff 15863 itemsize 16
inode ref index 2 namelen 6 name: foobar
item 6 key (257 EXTENT_DATA 0) itemoff 15810 itemsize 53
extent data disk byte 0 nr 0 gen 6
extent data offset 0 nr 24576 ram 266240
extent compression 0
item 7 key (257 EXTENT_DATA 24576) itemoff 15757 itemsize 53
prealloc data disk byte 12849152 nr 241664 gen 6
prealloc data offset 0 nr 241664
item 8 key (257 EXTENT_DATA 266240) itemoff 15704 itemsize 53
extent data disk byte 12845056 nr 4096 gen 6
extent data offset 0 nr 20480 ram 20480
extent compression 2
item 9 key (257 EXTENT_DATA 286720) itemoff 15651 itemsize 53
prealloc data disk byte 13090816 nr 405504 gen 6
prealloc data offset 0 nr 258048
The on disk extent at offset 266240 (which corresponds to 1 single disk block),
contains 5 compressed chunks of file data. Each of the first 4 compress 4096
bytes of file data, while the last one only compresses 3024 bytes of file data.
Therefore a read into the file region [285648 ; 286720[ (length = 4096 - 3024 =
1072 bytes) should always return zeroes (our next extent is a prealloc one).
The solution here is the compression code path to zero the remaining (untouched)
bytes of the last page it uncompressed data into, as the information about how
much space the file data consumes in the last page is not known in the upper layer
fs/btrfs/extent_io.c:__do_readpage(). In __do_readpage we were correctly zeroing
the remainder of the page but only if it corresponds to the last page of the inode
and if the inode's size is not a multiple of the page size.
This would cause not only returning random data on reads, but also permanently
storing random data when updating parts of the region that should be zeroed.
For the example above, it means updating a single byte in the region [285648 ; 286720[
would store that byte correctly but also store random data on disk.
A test case for xfstests follows soon.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
A user reported a 100% cpu hang with my new delayed ref code. Turns out I
forgot to increase the count check when we can't run a delayed ref because of
the tree mod log. If we can't run any delayed refs during this there is no
point in continuing to look, and we need to break out. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Added in patch "btrfs: add ioctls to query/change feature bits online"
modifications to superblock don't need to reserve metadata blocks when
starting a transaction.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
The set_fslabel ioctl uses btrfs_end_transaction, which means it's
possible that the change will be lost if the system crashes, same for
the newly set features. Let's use btrfs_commit_transaction instead.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
Wang noticed that he was failing btrfs/030 even though me and Filipe couldn't
reproduce. Turns out this is because Wang didn't have CONFIG_BTRFS_ASSERT set,
which meant that a key part of Filipe's original patch was not being built in.
This appears to be a mess up with merging Filipe's patch as it does not exist in
his original patch. Fix this by changing how we make sure del_waiting_dir_move
asserts that it did not error and take the function out of the ifdef check.
This makes btrfs/030 pass with the assert on or off. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Filipe Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Filipe is fixing compile and boot problems with our crc32c rework, and
Josef has disabled snapshot aware defrag for now.
As the number of snapshots increases, we're hitting OOM. For the
short term we're disabling things until a bigger fix is ready"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use late_initcall instead of module_init
Btrfs: use btrfs_crc32c everywhere instead of libcrc32c
Btrfs: disable snapshot aware defrag for now
|