| Age | Commit message (Collapse) | Author |
|---|
|
commit a27ba2607e60312554cbcd43fc660b2c7f29dc9c upstream.
The struct xfs_agfl v5 header was originally introduced with
unexpected padding that caused the AGFL to operate with one less
slot than intended. The header has since been packed, but the fix
left an incompatibility for users who upgrade from an old kernel
with the unpacked header to a newer kernel with the packed header
while the AGFL happens to wrap around the end. The newer kernel
recognizes one extra slot at the physical end of the AGFL that the
previous kernel did not. The new kernel will eventually attempt to
allocate a block from that slot, which contains invalid data, and
cause a crash.
This condition can be detected by comparing the active range of the
AGFL to the count. While this detects a padding mismatch, it can
also trigger false positives for unrelated flcount corruption. Since
we cannot distinguish a size mismatch due to padding from unrelated
corruption, we can't trust the AGFL enough to simply repopulate the
empty slot.
Instead, avoid unnecessarily complex detection logic and and use a
solution that can handle any form of flcount corruption that slips
through read verifiers: distrust the entire AGFL and reset it to an
empty state. Any valid blocks within the AGFL are intentionally
leaked. This requires xfs_repair to rectify (which was already
necessary based on the state the AGFL was found in). The reset
mitigates the side effect of the padding mismatch problem from a
filesystem crash to a free space accounting inconsistency. The
generic approach also means that this patch can be safely backported
to kernels with or without a packed struct xfs_agfl.
Check the AGF for an invalid freelist count on initial read from
disk. If detected, set a flag on the xfs_perag to indicate that a
reset is required before the AGFL can be used. In the first
transaction that attempts to use a flagged AGFL, reset it to empty,
warn the user about the inconsistency and allow the freelist fixup
code to repopulate the AGFL with new blocks. The xfs_perag flag is
cleared to eliminate the need for repeated checks on each block
allocation operation.
This allows kernels that include the packing fix commit 96f859d52bcb
("libxfs: pack the agfl header structure so XFS_AGFL_SIZE is correct")
to handle older unpacked AGFL formats without a filesystem crash.
Suggested-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by Dave Chiluk <chiluk+linuxxfs@indeed.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Dave Chiluk <chiluk+linuxxfs@indeed.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8c81dd46ef3c416b3b95e3020fb90dbd44e6140b ]
Forcing the log to disk after reading the agf is wrong, we might be
calling xfs_log_force with XFS_LOG_SYNC with a metadata lock held.
This can cause a deadlock when racing a fstrim with a filesystem
shutdown.
The deadlock has been identified due a miscalculation bug in device-mapper
dm-thin, which returns lack of space to its users earlier than the device itself
really runs out of space, changing the device-mapper volume into an error state.
The problem happened while filling the filesystem with a single file,
triggering the bug in device-mapper, consequently causing an IO error
and shutting down the filesystem.
If such file is removed, and fstrim executed before the XFS finishes the
shut down process, the fstrim process will end up holding the buffer
lock, and going to sleep on the cil wait queue.
At this point, the shut down process will try to wake up all the threads
waiting on the cil wait queue, but for this, it will try to hold the
same buffer log already held my the fstrim, locking up the filesystem.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d83fb14258b9961920cd86f0b921caaeb3ebe85 upstream.
During the "insert range" fallocate operation, i_size grows by the
specified 'len' bytes. XFS verifies that i_size + len < s_maxbytes, as
it should. But this comparison is done using the signed 'loff_t', and
'i_size + len' can wrap around to a negative value, causing the check to
incorrectly pass, resulting in an inode with "negative" i_size. This is
possible on 64-bit platforms, where XFS sets s_maxbytes = LLONG_MAX.
ext4 and f2fs don't run into this because they set a smaller s_maxbytes.
Fix it by using subtraction instead.
Reproducer:
xfs_io -f file -c "truncate $(((1<<63)-1))" -c "finsert 0 4096"
Fixes: a904b1ca5751 ("xfs: Add support FALLOC_FL_INSERT_RANGE for fallocate")
Cc: <stable@vger.kernel.org> # v4.1+
Originally-From: Eric Biggers <ebiggers@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: fix signed integer addition overflow too]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3a3882ff26fbdbaf5f7e13f6a0bccfbf7121041d ]
xfs_qm_init_quotainfo() does not check result of register_shrinker()
which was tagged as __must_check recently, reported by sparse.
Signed-off-by: Aliaksei Karaliou <akaraliou.dev@gmail.com>
[darrick: move xfs_qm_destroy_quotainos nearer xfs_qm_init_quotainos]
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2196881566225f3c3428d1a5f847a992944daa5b ]
xfs_qm_destroy_quotainfo() does not destroy quotainfo->qi_tree_lock
while destroys quotainfo->qi_quotaofflock.
Signed-off-by: Aliaksei Karaliou <akaraliou.dev@gmail.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 373b0589dc8d58bc09c9a28d03611ae4fb216057 ]
Once the inode item writeback errors is already fixed, it's time to fix the same
problem in dquot code.
Although there were no reports of users hitting this bug in dquot code (at least
none I've seen), the bug is there and I was already planning to fix it when the
correct approach to fix the inodes part was decided.
This patch aims to fix the same problem in dquot code, regarding failed buffers
being unable to be resubmitted once they are flush locked.
Tested with the recently test-case sent to fstests list by Hou Tao.
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 22a6c83777ac7c17d6c63891beeeac24cf5da450 ]
Fix some complaints from the UBSAN about signed integer addition overflows.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d210a9874b8f6166579408131cb74495caff1958 ]
percpu_counter_init failure path doesn't clean up &btp->bt_lru list.
Call list_lru_destroy in that error path. Similarly register_shrinker
error path is not handled.
While it is unlikely to trigger these error path, it is not impossible
especially the later might fail with large NUMAs. Let's handle the
failure to make the code more robust.
Noticed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 98c4f78dcdd8cec112d1cbc5e9a792ee6e5ab7a6 ]
In xfs_ifree, we reset the data/attr forks to extents format without
bothering to free any inline data buffer that might still be around
after all the blocks have been truncated off the file. Prior to commit
43518812d2 ("xfs: remove support for inlining data/extents into the
inode fork") nobody noticed because the leftover inline data after
truncation was small enough to fit inside the inline buffer inside the
fork itself.
However, now that we've removed the inline buffer, we /always/ have to
free the inline data buffer or else we leak them like crazy. This test
was found by turning on kmemleak for generic/001 or generic/388.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5e422f5e4fd71d18bc6b851eeb3864477b3d842e ]
There was one spot in xfs_bmap_add_extent_unwritten_real that didn't use the
passed in new extent state but always converted to normal, leading to wrong
behavior when converting from normal to unwritten.
Only found by code inspection, it seems like this code path to move partial
extent from written to unwritten while merging it with the next extent is
rarely exercised.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9f2a4505800607e537e9dd9dea4f55c4b0c30c7a ]
It is possible for mkfs to format very small filesystems with too
small of an internal log with respect to the various minimum size
and block count requirements. If this occurs when the log happens to
be smaller than the scan window used for cycle verification and the
scan wraps the end of the log, the start_blk calculation in
xlog_find_head() underflows and leads to an attempt to scan an
invalid range of log blocks. This results in log recovery failure
and a failed mount.
Since there may be filesystems out in the wild with this kind of
geometry, we cannot simply refuse to mount. Instead, cap the scan
window for cycle verification to the size of the physical log. This
ensures that the cycle verification proceeds as expected when the
scan wraps the end of the log.
Reported-by: Zorro Lang <zlang@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 350976ae21873b0d36584ea005076356431b8f79 ]
On truncate down, if new size is not block size aligned, we zero the
rest of block to avoid exposing stale data to user, and
iomap_truncate_page() skips zeroing if the range is already in
unwritten state or a hole. Then we writeback from on-disk i_size to
the new size if this range hasn't been written to disk yet, and
truncate page cache beyond new EOF and set in-core i_size.
The problem is that we could write data between di_size and newsize
before removing the page cache beyond newsize, as the extents may
still be in unwritten state right after a buffer write. As such, the
page of data that newsize lies in has not been zeroed by page cache
invalidation before it is written, and xfs_do_writepage() hasn't
triggered it's "zero data beyond EOF" case because we haven't
updated in-core i_size yet. Then a subsequent mmap read could see
non-zeros past EOF.
I occasionally see this in fsx runs in fstests generic/112, a
simplified fsx operation sequence is like (assuming 4k block size
xfs):
fallocate 0x0 0x1000 0x0 keep_size
write 0x0 0x1000 0x0
truncate 0x0 0x800 0x1000
punch_hole 0x0 0x800 0x800
mapread 0x0 0x800 0x800
where fallocate allocates unwritten extent but doesn't update
i_size, buffer write populates the page cache and extent is still
unwritten, truncate skips zeroing page past new EOF and writes the
page to disk, punch_hole invalidates the page cache, at last mapread
reads the block back and sees non-zero beyond EOF.
Fix it by moving truncate_setsize() to before writeback so the page
cache invalidation zeros the partial page at the new EOF. This also
triggers "zero data beyond EOF" in xfs_do_writepage() at writeback
time, because newsize has been set and page straddles the newsize.
Also fixed the wrong 'end' param of filemap_write_and_wait_range()
call while we're at it, the 'end' is inclusive and should be
'newsize - 1'.
Suggested-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eryu Guan <eguan@redhat.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 962cc1ad6caddb5abbb9f0a43e5abe7131a71f18 ]
In commit f2e9ad21 ("xfs: check for race with xfs_reclaim_inode"), we
skip an inode if we're racing with freeing the inode via
xfs_reclaim_inode, but we forgot to release the rcu read lock when
dumping the inode, with the result that we exit to userspace with a lock
held. Don't do that; generic/320 with a 1k block size fails this
very occasionally.
================================================
WARNING: lock held when returning to user space!
4.14.0-rc6-djwong #4 Tainted: G W
------------------------------------------------
rm/30466 is leaving the kernel with locks still held!
1 lock held by rm/30466:
#0: (rcu_read_lock){....}, at: [<ffffffffa01364d3>] xfs_ifree_cluster.isra.17+0x2c3/0x6f0 [xfs]
------------[ cut here ]------------
WARNING: CPU: 1 PID: 30466 at kernel/rcu/tree_plugin.h:329 rcu_note_context_switch+0x71/0x700
Modules linked in: deadline_iosched dm_snapshot dm_bufio ext4 mbcache jbd2 dm_flakey xfs libcrc32c dax_pmem device_dax nd_pmem sch_fq_codel af_packet [last unloaded: scsi_debug]
CPU: 1 PID: 30466 Comm: rm Tainted: G W 4.14.0-rc6-djwong #4
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.10.2-1ubuntu1djwong0 04/01/2014
task: ffff880037680000 task.stack: ffffc90001064000
RIP: 0010:rcu_note_context_switch+0x71/0x700
RSP: 0000:ffffc90001067e50 EFLAGS: 00010002
RAX: 0000000000000001 RBX: ffff880037680000 RCX: ffff88003e73d200
RDX: 0000000000000002 RSI: ffffffff819e53e9 RDI: ffffffff819f4375
RBP: 0000000000000000 R08: 0000000000000000 R09: ffff880062c900d0
R10: 0000000000000000 R11: 0000000000000000 R12: ffff880037680000
R13: 0000000000000000 R14: ffffc90001067eb8 R15: ffff880037680690
FS: 00007fa3b8ce8700(0000) GS:ffff88003ec00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f69bf77c000 CR3: 000000002450a000 CR4: 00000000000006e0
Call Trace:
__schedule+0xb8/0xb10
schedule+0x40/0x90
exit_to_usermode_loop+0x6b/0xa0
prepare_exit_to_usermode+0x7a/0x90
retint_user+0x8/0x20
RIP: 0033:0x7fa3b87fda87
RSP: 002b:00007ffe41206568 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff02
RAX: 0000000000000000 RBX: 00000000010e88c0 RCX: 00007fa3b87fda87
RDX: 0000000000000000 RSI: 00000000010e89c8 RDI: 0000000000000005
RBP: 0000000000000000 R08: 0000000000000003 R09: 0000000000000000
R10: 000000000000015e R11: 0000000000000246 R12: 00000000010c8060
R13: 00007ffe41206690 R14: 0000000000000000 R15: 0000000000000000
---[ end trace e88f83bf0cfbd07d ]---
Fixes: f2e9ad212def50bcf4c098c6288779dd97fff0f0
Cc: Omar Sandoval <osandov@fb.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40214d128e07dd21bb07a8ed6a7fe2f911281ab2 upstream.
The writeback rework in commit fbcc02561359 ("xfs: Introduce
writeback context for writepages") introduced a subtle change in
behavior with regard to the block mapping used across the
->writepages() sequence. The previous xfs_cluster_write() code would
only flush pages up to EOF at the time of the writepage, thus
ensuring that any pages due to file-extending writes would be
handled on a separate cycle and with a new, updated block mapping.
The updated code establishes a block mapping in xfs_writepage_map()
that could extend beyond EOF if the file has post-eof preallocation.
Because we now use the generic writeback infrastructure and pass the
cached mapping to each writepage call, there is no implicit EOF
limit in place. If eofblocks trimming occurs during ->writepages(),
any post-eof portion of the cached mapping becomes invalid. The
eofblocks code has no means to serialize against writeback because
there are no pages associated with post-eof blocks. Therefore if an
eofblocks trim occurs and is followed by a file-extending buffered
write, not only has the mapping become invalid, but we could end up
writing a page to disk based on the invalid mapping.
Consider the following sequence of events:
- A buffered write creates a delalloc extent and post-eof
speculative preallocation.
- Writeback starts and on the first writepage cycle, the delalloc
extent is converted to real blocks (including the post-eof blocks)
and the mapping is cached.
- The file is closed and xfs_release() trims post-eof blocks. The
cached writeback mapping is now invalid.
- Another buffered write appends the file with a delalloc extent.
- The concurrent writeback cycle picks up the just written page
because the writeback range end is LLONG_MAX. xfs_writepage_map()
attributes it to the (now invalid) cached mapping and writes the
data to an incorrect location on disk (and where the file offset is
still backed by a delalloc extent).
This problem is reproduced by xfstests test generic/464, which
triggers racing writes, appends, open/closes and writeback requests.
To address this problem, trim the mapping used during writeback to
within EOF when the mapping is validated. This ensures the mapping
is revalidated for any pages encountered beyond EOF as of the time
the current mapping was cached or last validated.
Reported-by: Eryu Guan <eguan@redhat.com>
Diagnosed-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 793d7dbe6d82a50b9d14bf992b9eaacb70a11ce6 upstream.
Recently we've had warnings arise from the vm handing us pages
without bufferheads attached to them. This should not ever occur
in XFS, but we don't defend against it properly if it does. The only
place where we remove bufferheads from a page is in
xfs_vm_releasepage(), but we can't tell the difference here between
"page is dirty so don't release" and "page is dirty but is being
invalidated so release it".
In some places that are invalidating pages ask for pages to be
released and follow up afterward calling ->releasepage by checking
whether the page was dirty and then aborting the invalidation. This
is a possible vector for releasing buffers from a page but then
leaving it in the mapping, so we really do need to avoid dirty pages
in xfs_vm_releasepage().
To differentiate between invalidated pages and normal pages, we need
to clear the page dirty flag when invalidating the pages. This can
be done through xfs_vm_invalidatepage(), and will result
xfs_vm_releasepage() seeing the page as clean which matches the
bufferhead state on the page after calling block_invalidatepage().
Hence we can re-add the page dirty check in xfs_vm_releasepage to
catch the case where we might be releasing a page that is actually
dirty and so should not have the bufferheads on it removed. This
will remove one possible vector of "dirty page with no bufferheads"
and so help narrow down the search for the root cause of that
problem.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 93e8befc17f6d6ea92b0aee3741ceac8bca4590f upstream.
Jason reported that a corrupted filesystem failed to replay
the log with a metadata block out of bounds warning:
XFS (dm-2): _xfs_buf_find: Block out of range: block 0x80270fff8, EOFS 0x9c40000
_xfs_buf_find() and xfs_btree_get_bufs() return NULL if
that happens, and then when xfs_alloc_fix_freelist() calls
xfs_trans_binval() on that NULL bp, we oops with:
BUG: unable to handle kernel NULL pointer dereference at 00000000000000f8
We don't handle _xfs_buf_find errors very well, every
caller higher up the stack gets to guess at why it failed.
But we should at least handle it somehow, so return
EFSCORRUPTED here.
Reported-by: Jason L Tibbitts III <tibbs@math.uh.edu>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f35c5e10c6ed6ba52a8dd8573924a80b6a02f03f upstream.
xfs_attr3_root_inactive() walks the attr fork tree to invalidate the
associated blocks. xfs_attr3_node_inactive() recursively descends
from internal blocks to leaf blocks, caching block address values
along the way to revisit parent blocks, locate the next entry and
descend down that branch of the tree.
The code that attempts to reread the parent block is unsafe because
it assumes that the local xfs_da_node_entry pointer remains valid
after an xfs_trans_brelse() and re-read of the parent buffer. Under
heavy memory pressure, it is possible that the buffer has been
reclaimed and reallocated by the time the parent block is reread.
This means that 'btree' can point to an invalid memory address, lead
to a random/garbage value for child_fsb and cause the subsequent
read of the attr fork to go off the rails and return a NULL buffer
for an attr fork offset that is most likely not allocated.
Note that this problem can be manufactured by setting
XFS_ATTR_BTREE_REF to 0 to prevent LRU caching of attr buffers,
creating a file with a multi-level attr fork and removing it to
trigger inactivation.
To address this problem, reinit the node/btree pointers to the
parent buffer after it has been re-read. This ensures btree points
to a valid record and allows the walk to proceed.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 67f2ffe31d1a683170c2ba0ecc643e42a5fdd397 upstream.
If we get ENOSPC half way through setting the ACL, the inode mode
can still be changed even though the ACL does not exist. Reorder the
operation to only change the mode of the inode if the ACL is set
correctly.
Whilst this does not fix the problem with crash consistency (that requires
attribute addition to be a deferred op) it does prevent ENOSPC and other
non-fatal errors setting an xattr to be handled sanely.
This fixes xfstests generic/449.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb9c2e5433250f5b477035dc478314f8e6dd5e36 upstream.
Various utility functions and interfaces that iterate internal
devices try to reference the realtime device even when RT support is
not compiled into the kernel.
Make sure this code is excluded from the CONFIG_XFS_RT=n build,
and where appropriate stub functions to return fatal errors if
they ever get called when RT support is not present.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 20413e37d71befd02b5846acdaf5e2564dd1c38e upstream.
Prevent kmemcheck from throwing warnings about reading uninitialised
memory when formatting inodes into the incore log buffer. There are
several issues here - we don't always log all the fields in the
inode log format item, and we never log the inode the
di_next_unlinked field.
In the case of the inode log format item, this is exacerbated
by the old xfs_inode_log_format structure padding issue. Hence make
the padded, 64 bit aligned version of the structure the one we always
use for formatting the log and get rid of the 64 bit variant. This
means we'll always log the 64-bit version and so recovery only needs
to convert from the unpadded 32 bit version from older 32 bit
kernels.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e12199f85d0ad1b04ce6c425ad93cd847fe930bb upstream.
If we got two AIO writes into a COW area the second one might not have any
COW extents left to convert. Handle that case gracefully instead of
triggering an assert or accessing beyond the bounds of the extent list.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52bfcdd7adbc26639bc7b2356ab9a3f5dad68ad6 upstream.
Since the CoW fork exists as a secondary data structure to the data
fork, we must always swap cow forks during swapext. We also need to
swap the extent counts and reset the cowblocks tags.
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 842f6e9f786226c58fcbd5ef80eadca72fdfe652 upstream.
My previous patch: d3a304b6292168b83b45d624784f973fdc1ca674 check for
XFS_LI_FAILED flag xfs_iflush done, so the failed item can be properly
resubmitted.
In the loop scanning other inodes being completed, it should check the
current item for the XFS_LI_FAILED, and not the initial one.
The state of the initial inode is checked after the loop ends
Kudos to Eric for catching this.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9789dd9e1d939232e8ff4c50ef8e75aa6781b3fb upstream.
We call __xfs_ag_resv_init to make a per-AG reservation for each AG.
This makes the reservation per-AG, not per-filesystem. Therefore, it
is incorrect to adjust m_ag_max_usable for each AG. Adjust it only
when we're reserving AG 0's blocks so that we only do it once per fs.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee70daaba82d70766d0723b743d9fdeb3b06102a upstream.
Since commit d531d91d6990 ("xfs: always use unwritten extents for
direct I/O writes"), we start allocating unwritten extents for all
direct writes to allow appending aio in XFS.
But for dio writes that could extend file size we update the in-core
inode size first, then convert the unwritten extents to real
allocations at dio completion time in xfs_dio_write_end_io(). Thus a
racing direct read could see the new i_size and find the unwritten
extents first and read zeros instead of actual data, if the direct
writer also takes a shared iolock.
Fix it by updating the in-core inode size after the unwritten extent
conversion. To do this, introduce a new boolean argument to
xfs_iomap_write_unwritten() to tell if we want to update in-core
i_size or not.
Suggested-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
[hch: backported to the old direct I/O code before Linux 4.10]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d20a5e3851969fa685f118a80e4df670255a4e8d upstream.
The 'did_zero' param of xfs_zero_range() was not passed to
iomap_zero_range() correctly. This was introduced by commit
7bb41db3ea16 ("xfs: handle 64-bit length in xfs_iozero"), and found
by code inspection.
Signed-off-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e150dcd459e1b441eaf08f341a986f04e61bf3b8 upstream.
Use the %pS instead of the %pF printk format specifier for printing symbols
from direct addresses. This is needed for the ia64, ppc64 and parisc64
architectures.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3af423b03435c81036fa710623d3ae92fbe346a3 upstream.
When we perform an finsert/fcollapse operation, cancel all the CoW
extents for the affected file offset range so that they don't end up
pointing to the wrong blocks.
Reported-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cc6f77710a6de6210f9feda7cd53e2f5ee7a7e69 upstream.
If we have speculative cow preallocations hanging around in the cow
fork, don't let a truncate operation clear the reflink flag because if
we do then there's a chance we'll forget to free those extents when we
destroy the incore inode.
Reported-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 08b005f1333154ae5b404ca28766e0ffb9f1c150 ]
The sole remaining caller of kmem_zalloc_greedy is bulkstat, which uses
it to grab 1-4 pages for staging of inobt records. The infinite loop in
the greedy allocation function is causing hangs[1] in generic/269, so
just get rid of the greedy allocator in favor of kmem_zalloc_large.
This makes bulkstat somewhat more likely to ENOMEM if there's really no
pages to spare, but eliminates a source of hangs.
[1] http://lkml.kernel.org/r/20170301044634.rgidgdqqiiwsmfpj%40XZHOUW.usersys.redhat.com
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6851a3db7e224bbb85e23b3c64a506c9e0904382 upstream.
Currently only the blocksize is checked, but we should really be calling
bdev_dax_supported() which also tests to make sure we can get a
struct dax_device and that the dax_direct_access() path is working.
This is the same check that we do for the "-o dax" mount option in
xfs_fs_fill_super().
This does not fix the race issues that caused the XFS DAX inode option to
be disabled, so that option will still be disabled. If/when we re-enable
it, though, I think we will want this issue to have been fixed. I also do
think that we want to fix this in stable kernels.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7bf7a193a90cadccaad21c5970435c665c40fe27 upstream.
Fix up all the compiler warnings that have crept in.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6c370590cfe0c36bcd62d548148aa65c984540b7 upstream.
In function xfs_test_remount_options(), kfree() is used to free memory
allocated by kmem_zalloc(). But it is better to use kmem_free().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8353a814f2518dcfa79a5bb77afd0e7dfa391bb1 upstream.
Our loop in xfs_finish_page_writeback, which iterates over all buffer
heads in a page and then calls end_buffer_async_write, which also
iterates over all buffers in the page to check if any I/O is in flight
is not only inefficient, but also potentially dangerous as
end_buffer_async_write can cause the page and all buffers to be freed.
Replace it with a single loop that does the work of end_buffer_async_write
on a per-page basis.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd60687ee541ca3f6df8758f38e6f22f57c42a37 upstream.
Reject attempts to set XFLAGS that correspond to di_flags2 inode flags
if the inode isn't a v3 inode, because di_flags2 only exists on v3.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 47c7d0b19502583120c3f396c7559e7a77288a68 upstream.
When calling into _xfs_log_force{,_lsn}() with a pointer
to log_flushed variable, log_flushed will be set to 1 if:
1. xlog_sync() is called to flush the active log buffer
AND/OR
2. xlog_wait() is called to wait on a syncing log buffers
xfs_file_fsync() checks the value of log_flushed after
_xfs_log_force_lsn() call to optimize away an explicit
PREFLUSH request to the data block device after writing
out all the file's pages to disk.
This optimization is incorrect in the following sequence of events:
Task A Task B
-------------------------------------------------------
xfs_file_fsync()
_xfs_log_force_lsn()
xlog_sync()
[submit PREFLUSH]
xfs_file_fsync()
file_write_and_wait_range()
[submit WRITE X]
[endio WRITE X]
_xfs_log_force_lsn()
xlog_wait()
[endio PREFLUSH]
The write X is not guarantied to be on persistent storage
when PREFLUSH request in completed, because write A was submitted
after the PREFLUSH request, but xfs_file_fsync() of task A will
be notified of log_flushed=1 and will skip explicit flush.
If the system crashes after fsync of task A, write X may not be
present on disk after reboot.
This bug was discovered and demonstrated using Josef Bacik's
dm-log-writes target, which can be used to record block io operations
and then replay a subset of these operations onto the target device.
The test goes something like this:
- Use fsx to execute ops of a file and record ops on log device
- Every now and then fsync the file, store md5 of file and mark
the location in the log
- Then replay log onto device for each mark, mount fs and compare
md5 of file to stored value
Cc: Christoph Hellwig <hch@lst.de>
Cc: Josef Bacik <jbacik@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 742d84290739ae908f1b61b7d17ea382c8c0073a upstream.
Currently flag switching can be used to easily crash the kernel. Disable
the per-inode DAX flag until that is sorted out.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2dd3d709fc4338681a3aa61658122fa8faa5a437 upstream.
The owner change bmbt scan that occurs during extent swap operations
does not handle ordered buffer failures. Buffers that cannot be
marked ordered must be physically logged so previously dirty ranges
of the buffer can be relogged in the transaction.
Since the bmbt scan may need to process and potentially log a large
number of blocks, we can't expect to complete this operation in a
single transaction. Update extent swap to use a permanent
transaction with enough log reservation to physically log a buffer.
Update the bmbt scan to physically log any buffers that cannot be
ordered and to terminate the scan with -EAGAIN. On -EAGAIN, the
caller rolls the transaction and restarts the scan. Finally, update
the bmbt scan helper function to skip bmbt blocks that already match
the expected owner so they are not reprocessed after scan restarts.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[darrick: fix the xfs_trans_roll call]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5814bceea48ee1c57c4db2bd54b0c0246daf54a upstream.
Ordered buffers are used in situations where the buffer is not
physically logged but must pass through the transaction/logging
pipeline for a particular transaction. As a result, ordered buffers
are not unpinned and written back until the transaction commits to
the log. Ordered buffers have a strict requirement that the target
buffer must not be currently dirty and resident in the log pipeline
at the time it is marked ordered. If a dirty+ordered buffer is
committed, the buffer is reinserted to the AIL but not physically
relogged at the LSN of the associated checkpoint. The buffer log
item is assigned the LSN of the latest checkpoint and the AIL
effectively releases the previously logged buffer content from the
active log before the buffer has been written back. If the tail
pushes forward and a filesystem crash occurs while in this state, an
inconsistent filesystem could result.
It is currently the caller responsibility to ensure an ordered
buffer is not already dirty from a previous modification. This is
unclear and error prone when not used in situations where it is
guaranteed a buffer has not been previously modified (such as new
metadata allocations).
To facilitate general purpose use of ordered buffers, update
xfs_trans_ordered_buf() to conditionally order the buffer based on
state of the log item and return the status of the result. If the
bli is dirty, do not order the buffer and return false. The caller
must either physically log the buffer (having acquired the
appropriate log reservation) or push it from the AIL to clean it
before it can be marked ordered in the current transaction.
Note that ordered buffers are currently only used in two situations:
1.) inode chunk allocation where previously logged buffers are not
possible and 2.) extent swap which will be updated to handle ordered
buffer failures in a separate patch.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6fb10d6d22094bc4062f92b9ccbcee2f54033d04 upstream.
The extent swap operation currently resets bmbt block owners before
the inode forks are swapped. The bmbt buffers are marked as ordered
so they do not have to be physically logged in the transaction.
This use of ordered buffers is not safe as bmbt buffers may have
been previously physically logged. The bmbt owner change algorithm
needs to be updated to physically log buffers that are already dirty
when/if they are encountered. This means that an extent swap will
eventually require multiple rolling transactions to handle large
btrees. In addition, all inode related changes must be logged before
the bmbt owner change scan begins and can roll the transaction for
the first time to preserve fs consistency via log recovery.
In preparation for such fixes to the bmbt owner change algorithm,
refactor the bmbt scan out of the extent fork swap code to the last
operation before the transaction is committed. Update
xfs_swap_extent_forks() to only set the inode log flags when an
owner change scan is necessary. Update xfs_swap_extents() to trigger
the owner change based on the inode log flags. Note that since the
owner change now occurs after the extent fork swap, the inode btrees
must be fixed up with the inode number of the current inode (similar
to log recovery).
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99c794c639a65cc7b74f30a674048fd100fe9ac8 upstream.
Extent swap uses xfs_btree_visit_blocks() to fix up bmbt block
owners on v5 (!rmapbt) filesystems. The bmbt scan uses
xfs_btree_lookup_get_block() to read bmbt blocks which verifies the
current owner of the block against the parent inode of the bmbt.
This works during extent swap because the bmbt owners are updated to
the opposite inode number before the inode extent forks are swapped.
The modified bmbt blocks are marked as ordered buffers which allows
everything to commit in a single transaction. If the transaction
commits to the log and the system crashes such that recovery of the
extent swap is required, log recovery restarts the bmbt scan to fix
up any bmbt blocks that may have not been written back before the
crash. The log recovery bmbt scan occurs after the inode forks have
been swapped, however. This causes the bmbt block owner verification
to fail, leads to log recovery failure and requires xfs_repair to
zap the log to recover.
Define a new invalid inode owner flag to inform the btree block
lookup mechanism that the current inode may be invalid with respect
to the current owner of the bmbt block. Set this flag on the cursor
used for change owner scans to allow this operation to work at
runtime and during log recovery.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Fixes: bb3be7e7c ("xfs: check for bogus values in btree block headers")
Cc: stable@vger.kernel.org
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8dc518dfa7dbd079581269e51074b3c55a65a880 upstream.
Ordered buffers are attached to transactions and pushed through the
logging infrastructure just like normal buffers with the exception
that they are not actually written to the log. Therefore, we don't
need to log dirty ranges of ordered buffers. xfs_trans_log_buf() is
called on ordered buffers to set up all of the dirty state on the
transaction, buffer and log item and prepare the buffer for I/O.
Now that xfs_trans_dirty_buf() is available, call it from
xfs_trans_ordered_buf() so the latter is now mutually exclusive with
xfs_trans_log_buf(). This reflects the implementation of ordered
buffers and helps eliminate confusion over the need to log ranges of
ordered buffers just to set up internal log state.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Allison Henderson <allison.henderson@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9684010d38eccda733b61106765e9357cf436f65 upstream.
xfs_trans_log_buf() is responsible for logging the dirty segments of
a buffer along with setting all of the necessary state on the
transaction, buffer, bli, etc., to ensure that the associated items
are marked as dirty and prepared for I/O. We have a couple use cases
that need to to dirty a buffer in a transaction without actually
logging dirty ranges of the buffer. One existing use case is
ordered buffers, which are currently logged with arbitrary ranges to
accomplish this even though the content of ordered buffers is never
written to the log. Another pending use case is to relog an already
dirty buffer across rolled transactions within the deferred
operations infrastructure. This is required to prevent a held
(XFS_BLI_HOLD) buffer from pinning the tail of the log.
Refactor xfs_trans_log_buf() into a new function that contains all
of the logic responsible to dirty the transaction, lidp, buffer and
bli. This new function can be used in the future for the use cases
outlined above. This patch does not introduce functional changes.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Allison Henderson <allison.henderson@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9385cc6fb7edf23702de33a2dc82965d92d9392 upstream.
Ordered buffers pass through the logging infrastructure without ever
being written to the log. The way this works is that the ordered
buffer status is transferred to the log vector at commit time via
the ->iop_size() callback. In xlog_cil_insert_format_items(),
ordered log vectors bypass ->iop_format() processing altogether.
Therefore it is unnecessary for xfs_buf_item_format() to handle
ordered buffers. Remove the unnecessary logic and assert that an
ordered buffer never reaches this point.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6453c65d3576bc3e602abb5add15f112755c08ca upstream.
xfs_buf_item_unlock() historically checked the dirty state of the
buffer by manually checking the buffer log formats for dirty
segments. The introduction of ordered buffers invalidated this check
because ordered buffers have dirty bli's but no dirty (logged)
segments. The check was updated to accommodate ordered buffers by
looking at the bli state first and considering the blf only if the
bli is clean.
This logic is safe but unnecessary. There is no valid case where the
bli is clean yet the blf has dirty segments. The bli is set dirty
whenever the blf is logged (via xfs_trans_log_buf()) and the blf is
cleared in the only place BLI_DIRTY is cleared (xfs_trans_binval()).
Remove the conditional blf dirty checks and replace with an assert
that should catch any discrepencies between bli and blf dirty
states. Refactor the old blf dirty check into a helper function to
be used by the assert.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a4f6cf6b2b6b60ec2a05a33a32e65caa4149aa2b upstream.
It checks a single flag and has one caller. It probably isn't worth
its own function.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2e9ad212def50bcf4c098c6288779dd97fff0f0 upstream.
After xfs_ifree_cluster() finds an inode in the radix tree and verifies
that the inode number is what it expected, xfs_reclaim_inode() can swoop
in and free it. xfs_ifree_cluster() will then happily continue working
on the freed inode. Most importantly, it will mark the inode stale,
which will probably be overwritten when the inode slab object is
reallocated, but if it has already been reallocated then we can end up
with an inode spuriously marked stale.
In 8a17d7ddedb4 ("xfs: mark reclaimed inodes invalid earlier") we added
a second check to xfs_iflush_cluster() to detect this race, but the
similar RCU lookup in xfs_ifree_cluster() needs the same treatment.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 799ea9e9c59949008770aab4e1da87f10e99dbe4 upstream.
When we introduced the bmap redo log items, we set MS_ACTIVE on the
mountpoint and XFS_IRECOVERY on the inode to prevent unlinked inodes
from being truncated prematurely during log recovery. This also had the
effect of putting linked inodes on the lru instead of evicting them.
Unfortunately, we neglected to find all those unreferenced lru inodes
and evict them after finishing log recovery, which means that we leak
them if anything goes wrong in the rest of xfs_mountfs, because the lru
is only cleaned out on unmount.
Therefore, evict unreferenced inodes in the lru list immediately
after clearing MS_ACTIVE.
Fixes: 17c12bcd30 ("xfs: when replaying bmap operations, don't let unlinked inodes get reaped")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: viro@ZenIV.linux.org.uk
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d32311cf19bfb8c1d2b4601974ddd951f9cfd0b upstream.
In a filesystem without finobt, the Space manager selects an AG to alloc a new
inode, where xfs_dialloc_ag_inobt() will search the AG for the free slot chunk.
When the new inode is in the same AG as its parent, the btree will be searched
starting on the parent's record, and then retried from the top if no slot is
available beyond the parent's record.
To exit this loop though, xfs_dialloc_ag_inobt() relies on the fact that the
btree must have a free slot available, once its callers relied on the
agi->freecount when deciding how/where to allocate this new inode.
In the case when the agi->freecount is corrupted, showing available inodes in an
AG, when in fact there is none, this becomes an infinite loop.
Add a way to stop the loop when a free slot is not found in the btree, making
the function to fall into the whole AG scan which will then, be able to detect
the corruption and shut the filesystem down.
As pointed by Brian, this might impact performance, giving the fact we
don't reset the search distance anymore when we reach the end of the
tree, giving it fewer tries before falling back to the whole AG search, but
it will only affect searches that start within 10 records to the end of the tree.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e67d3d4246e5fbb0c7c700426d11241ca9c6f473 upstream.
Torn write detection and tail overwrite detection can shift the log
head and tail respectively in the event of CRC mismatch or
corruption errors. Add a high-level log recovery tracepoint to dump
the final log head/tail and make those values easily attainable in
debug/diagnostic situations.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
