| Age | Commit message (Collapse) | Author |
|---|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (82 commits)
[ARM] Add comments marking in-use ptrace numbers
[ARM] Move syscall saving out of the way of utrace
[ARM] 4360/1: S3C24XX: regs-udc.h remove unused macro
[ARM] 4358/1: S3C24XX: mach-qt2410.c: remove linux/mmc/protocol.h header
[ARM] mm 10: allow memory type to be specified with ioremap
[ARM] mm 9: add additional device memory types
[ARM] mm 8: define mem_types table L1 bit 4 to be for ARMv6
[ARM] iop: add missing parens in macro
[ARM] mm 7: remove duplicated __ioremap() prototypes
ARM: OMAP: fix OMAP1 mpuio suspend/resume oops
ARM: OMAP: MPUIO wake updates
ARM: OMAP: speed up gpio irq handling
ARM: OMAP: plat-omap changes for 2430 SDP
ARM: OMAP: gpio object shrinkage, cleanup
ARM: OMAP: /sys/kernel/debug/omap_gpio
ARM: OMAP: Implement workaround for GPIO wakeup bug in OMAP2420 silicon
ARM: OMAP: Enable 24xx GPIO autoidling
[ARM] 4318/2: DSM-G600 Board Support
[ARM] 4227/1: minor head.S fixups
[ARM] 4328/1: Move i.MX UART regs to driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (46 commits)
mmc-omap: Clean up omap set_ios and make MMC_POWER_ON work
mmc-omap: Fix omap to use MMC_POWER_ON
mmc-omap: add missing '\n'
mmc: make tifm_sd_set_dma_data() static
mmc: remove old card states
mmc: support unsafe resume of cards
mmc: separate out reading EXT_CSD
mmc: break apart switch function
MMC: Fix handling of low-voltage cards
MMC: Consolidate voltage definitions
mmc: add bus handler
wbsd: check for data opcode earlier
mmc: Separate out protocol ops
mmc: Move core functions to subdir
mmc: deprecate mmc bus topology
mmc: remove card upon suspend
mmc: allow suspended block driver to be removed
mmc: Flush pending detects on host removal
mmc: Move host and card drivers to subdirs
mmc: Move queue functions to mmc_block
...
|
|
All host drivers were #include:ing mmc/protocol.h just to
get access to the OCR bit defines. Move these to host.h instead.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
|
Conflicts:
drivers/usb/input/Makefile
drivers/usb/input/gtco.c
|
|
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Reposted patch for kernel 2.6.21-rc2.
The driver i2c-pxa doesn't set the class member in i2c_adapter, which
is used to register the I2C adapter. The hwmon (sensors) drivers (e.g.
adm1021) that are connected to a i2c-pxa adapter don't attach because
they expect that the adapter supports class I2C_CLASS_HWMON.
This patch adds functionality to allow platforms to set the class and
pass it as platform_data to the i2c-pxa driver. Sample usage in
platform code:
static struct i2c_pxa_platform_data my_i2c_platform_data = {
.class = I2C_CLASS_HWMON
};
static void __init my_platform_init(void)
{
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_i2c_info(&my_i2c_platform_data);
}
Signed-off-by: Matej Kenda <matej.kenda@hermes-softlab.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4278/1: configure pxa27x I2C SCL as "input"
[ARM] 4272/1: Missing symbol h1940_pm_return fix
[ARM] 4235/1: ns9xxx: declare the clock functions as "const"
[ARM] 4271/1: iop32x: fix ep80219 detection (support iq80219 platforms)
[ARM] 4270/2: mach-s3c2443/irq.c off by one error in dma irqs
|
|
It has been reported by Julian Deng that configuring the pxa27x i2c SCL line as output generates a short negative pulse on it during the call to pxa_gpio_mode(GPIO117_I2CSCL_MD); as it first switches it to output and then configures it for the alternate function. The SCL line is in fact bidirectional and can also be configured as 117 | GPIO_ALT_FN_1_IN, in which case the pulse is not generated. This is exactly what this patch does.
Author: Julian Deng <dengtj@sitek.cn>
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ... among other things, it can be some time before
a driver is ready. This patch corrects that oversight, fixing
- documentation
- platforms supporting the GPIO interface
- users of that call (just one for now, others are pending)
There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.
Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ... so those chips might not avoid the glitches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Based on the discussion last december (http://lkml.org/lkml/2006/12/20/242),
this patch:
- moves the PXA_LAST_GPIO check into pxa_gpio_mode
- fixes comment and includes in gpio.h
- replaces the gpio_set/get_value macros with inline
functions and adds a non-inline version to avoid
code explosion when gpio is not a constant.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
Conflicts:
include/asm-arm/arch-at91rm9200/entry-macro.S
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
|
|
|
|
get_irqnr_preamble allows machines to take some action before entering the
get_irqnr_and_base loop. On iop we enable cp6 access.
arch_ret_to_user is added to the userspace return path to allow individual
architectures to take actions, like disabling coprocessor access, before
the final return to userspace.
Per Nicolas Pitre's note, there is no need to cp_wait on the return to user
as the latency to return is sufficient.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The Lubbock platform uses both a PXA25x and a SA1111 at the same time.
Both chips have the same "Serial Audio Controller" registers although
the SA1111 one is never expected to be used in preference to the PXA25x
one. So let's disable the SA1111 defines whenever compilation is for a
PXA architecture and make the PXA defines always defined.
This removes a bunch of "already defined" warnings as well since the
current hack to prevent them depended on include ordering which wasn't
always right.
While at it, clean up the SA1111 defines allowing to get rid of the
__CCREG() macro.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Arch-neutral GPIO calls for PXA.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patchs adds some missing register bit defs for the PXA SSP ports audio registers and fixes up some other broken bit definitions as noticed by Russell.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch renames pxa_gpio_set/get functions defined in drivers/usb/gadget/pxa2xx_udc.h to udc_gpio_set/get.
These functions are moved from drivers/usb/gadget/pxa2xx_udc.h to include/asm-arm/arch-pxa2xx/udc.h
Creates new functions: udc_gpio_to_irq, udc_gpio_init_vbus, udc_gpio_init_pullup in include/asm-arm/arch-pxa2xx/udc.h. These functions are used in drivers/usb/gadget/pxa2xx_udc.c instead of direct low-level (pxa2xx only) functions.
Creates all these udc_gpio_* functions in include/asm-arm/arch-ixp4xx/udc.h. This implementation has no real code because ixp4xx doesn't use vbus - only vbus uses all these gpio functions (and because ixp4xx misses any function which converts number of gpio pin into it's irq).
This is next step to make pxa2xx_udc fully work on ixp4xx platform.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Of the possible SSP frame formats (FRF bits in SSCR0), only SSCR0_PSP is defined. Other possible formats are Motorola SPI (0<<4), TI SSP (1<<4) and Microwire (2<<4). Attached patch adds a definition SSCR0_TISSP.
This mode is used for the sound codec attached to the PXA272 SSP1 of some HTC PDA phones.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The SSCR0_SlotsPerFrm macro writes a 3-bit value to bits [2:0], while the correct location of FRDC in SSCR0 is at bits [26:24]. This patch adds the missing "<< 24".
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Stabilize PIO mode transfers against a range of word sizes and FIFO
thresholds and fixes word size setup/override issues.
1) 16 and 32 bit DMA/PIO transfers broken due to timing differences.
2) Potential for bad transfer counts due to transfer size assumptions.
3) Setup function broken is multiple ways.
4) Per transfer bit_per_word changes break DMA setup in pump_tranfers.
5) False positive timeout are not errors.
6) Changes in pxa2xx_spi_chip not effective in calls to setup.
7) Timeout scaling wrong for PXA255 NSSP.
8) Driver leaks memory while busy during unloading.
Known issues:
SPI_CS_HIGH and SPI_LSB_FIRST settings in struct spi_device are not handled.
Testing:
This patch has been test against the "random length, random bits/word,
random data (verified on loopback) and stepped baud rate by octaves
(3.6MHz to 115kHz)" test. It is robust in PIO mode, using any
combination of tx and rx thresholds, and also in DMA mode (which
internally computes the thresholds).
Much thanks to Ned Forrester for exhaustive reviews, fixes and testing.
The driver is substantially better for his efforts.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Merge:
Atmel AT91RM9200 and AT91SAM9260 changes
General ARM developments
Disconfiguous memory cleanups
64-bit/32-bit division and sched_clock extension patches
EP93xx support changes
IOP support changes
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Most architectures have fairly simple discontiguous memory - a
simple set of successive regions each containing some memory.
These can be described simply as a log2 of their maximum size,
along with the base address of the first region and the number
of regions.
The base address is already described by PHYS_PFN_OFFSET, and
the number of regions via the MAX_NUMNODES and the number of
online nodes.
If we then supply the log2 of their maximum size, all the other
discontigmem macros can move into generic code.
There is one exception: lh7a40x seems to have a more complicated
setup; this is left alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch updates a bit definition name to align with the PXA27x
spec.EORINTR(End-Of-Receive Intr) bit in DCSR register (DMA Channel
Control/Status Register)
Signed-off-by: Stanley Cai <stanley.w.cai@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch updates several bit definitions name in UDCISR1 register.
Signed-off-by: Stanley Cai <stanley.w.cai@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
multiple platforms
Move declaration of struct pxa2xx_udc_mach_info from
include/asm-arm/arch-pxa/udc.h to new file
include/asm-arm/mach/udc_pxa2xx.h.
This allow us to use this structure with
multiple platforms - pxa and ixp4xx. USB
device controller used in pxa25x is the same
as controller used in ixp4xx.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fixed definition of some CIF registers; see PXA27x Developer\'s Manual.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The PXA255 has 84 GPIO lines available. This patch allows access to 81-84
Signed-off-by: Craig Hughes <craig@gumstix.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds a register bit definition for the pxa27x SSP port Frame
Sync Relative Timing (FSRT) bit.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use the new typedef for interrupt handler function pointers rather than
actually spelling out the full thing each time. This was scripted with the
following small shell script:
#!/bin/sh
egrep -nHrl -e 'irqreturn_t[ ]*[(][*]' $* |
while read i
do
echo $i
perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $?
done
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
support
Add the ability to have pxafb use only certain fixed video modes
(selected on a per platform basis). This is useful on production
hardware such as the Zaurus cxx00 models where the valid modes are
known in advance and any other modes could result in hardware damage.
Following this, add support for the cxx00 QVGA mode. Mode information
is passed to the lcd_power call to allowing the panel drivers to
configure the display hardware accordingly (corgi_lcd already contains
the functionality for the cxx00 panel).
This mirrors the setup already used by w100fb.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This updates the PXA 25x UDC board-independent infrastructure for VBUS sensing
and the D+ pullup. The original code evolved from rather bizarre support on
Intel's "Lubbock" reference hardware, so that on more sensible hardware it
doesn't work as well as it could/should.
The change is just to teach the UDC driver how to use built-in PXA GPIO pins
directly. This reduces the amount of board-specfic object code needed, and
enables the use of a VBUS sensing IRQ on boards (like Gumstix) that have one.
With VBUS sensing, the UDC is unclocked until a host is actually connected.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Such timeouts were en
Patch from Paul Sokolovsky
This patch adds timeouts while working with SSP registers. Such
timeouts were envisioned by docstrings in ssp.c, but were not
implemented. There were actual lockups while accessing
touchscreen for iPaqs h1910, h4000 due to lack of the timeouts.
This is updated version of previously submitted patch: 3738/1.
Signed-off-by: Paul Sokolovsky <pmiscml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Jürgen Schindele
This patch adds support for Trizeps4 SoM and ConXS-evalboard
from "Keith und Koep" This DIMM-module is based on PXA270.
Signed-off-by: Jürgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Andrew Victor
Remove the remaining legacy __mem_isa() definitions for the ARM
platforms.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (42 commits)
[ARM] Fix tosa build error
[ARM] 3610/1: Make reboot work on Versatile
[ARM] 3609/1: S3C24XX: defconfig update for s3c2410_defconfig
[ARM] 3591/1: Anubis: IDE device definitions
[ARM] Include asm/hardware.h not asm/arch/hardware.h
[ARM] 3594/1: Poodle: Add touchscreen support + other updates
[ARM] 3564/1: sharpsl_pm: Abstract some machine specific parameters
[ARM] 3561/1: Poodle: Correct the MMC/SD power control
[ARM] 3593/1: Add reboot and shutdown handlers for Zaurus handhelds
[ARM] 3599/1: AT91RM9200 remove global variables
[ARM] 3607/1: AT91RM9200 misc fixes
[ARM] 3605/1: AT91RM9200 Power Management
[ARM] 3604/1: AT91RM9200 New boards
[ARM] 3603/1: AT91RM9200 remove old files
[ARM] 3592/1: AT91RM9200 Serial driver update
[ARM] 3590/1: AT91RM9200 Platform devices support
[ARM] 3589/1: AT91RM9200 DK/EK board update
[ARM] 3588/1: AT91RM9200 CSB337/637 board update
[ARM] 3587/1: AT91RM9200 hardware headers
[ARM] 3586/1: AT91RM9200 header update
...
|
|
* git://git.infradead.org/hdrcleanup-2.6: (63 commits)
[S390] __FD_foo definitions.
Switch to __s32 types in joystick.h instead of C99 types for consistency.
Add <sys/types.h> to headers included for userspace in <linux/input.h>
Move inclusion of <linux/compat.h> out of user scope in asm-x86_64/mtrr.h
Remove struct fddi_statistics from user view in <linux/if_fddi.h>
Move user-visible parts of drivers/s390/crypto/z90crypt.h to include/asm-s390
Revert include/media changes: Mauro says those ioctls are only used in-kernel(!)
Include <linux/types.h> and use __uXX types in <linux/cramfs_fs.h>
Use __uXX types in <linux/i2o_dev.h>, include <linux/ioctl.h> too
Remove private struct dx_hash_info from public view in <linux/ext3_fs.h>
Include <linux/types.h> and use __uXX types in <linux/affs_hardblocks.h>
Use __uXX types in <linux/divert.h> for struct divert_blk et al.
Use __u32 for elf_addr_t in <asm-powerpc/elf.h>, not u32. It's user-visible.
Remove PPP_FCS from user view in <linux/ppp_defs.h>, remove __P mess entirely
Use __uXX types in user-visible structures in <linux/nbd.h>
Don't use 'u32' in user-visible struct ip_conntrack_old_tuple.
Use __uXX types for S390 DASD volume label definitions which are user-visible
S390 BIODASDREADCMB ioctl should use __u64 not u64 type.
Remove unneeded inclusion of <linux/time.h> from <linux/ufs_fs.h>
Fix private integer types used in V4L2 ioctls.
...
Manually resolve conflict in include/linux/mtd/physmap.h
|
|
|
|
Patch from Liam Girdwood
This patch adds some new PXA27x SSP port registers and also fixes the
SSP slots per frame macro
Changes:-
o SSCR0_SlotPerFrm fixed
o Added SSP port TSA, RSA, TSS and ACD registers
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Richard Purdie
Poodle Updates:
* Update corgi_ssp to make the GPIO chip selects optional
* Enable corgi_ssp for use by poodle
* Add corgi touchscreen platform device for poodle
* Export locomo platform device.
* Set framebuffer device parent correctly
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Richard Purdie
Correct the Poodle power control for the MMC/SD port. Also
add write protection switch support.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Richard Purdie
Add functionality to allow machine specific reboot handlers on ARM.
Add machine specific reboot and poweroff handlers for all PXA Zaurus
models.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Richard Purdie
Add a power budget variable to the PXA OHCI platform data and add a
default value for the spitz platform(s) which prevents known failures
with certain USB devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
include/asm-powerpc/unistd.h
include/asm-sparc/unistd.h
include/asm-sparc64/unistd.h
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Fix some outstanding issues with the pxa2xx_spi driver when running on a
PXA270:
- Wrong timeout calculation in the setup function due to different
peripheral clock rates in the PXAxxx family.
- Bad handling of SSSR_TFS interrupts in interrupt_transfer function.
- Added locking to interface between the pump_messages workqueue and the
pump_transfers tasklet.
Much thanks to Juergen Beisert for the extensive testing on the PXA270.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master
controller (see Documentation/spi/spi_summary). The driver has the following
features:
- Support for any PXA2xx SSP
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
