| Age | Commit message (Collapse) | Author |
|---|
|
Add support for mmap'ed recvmsg(). To allow the kernel to construct messages
into the mapped area, a dataless skb is allocated and the data pointer is
set to point into the ring frame. This means frames will be delivered to
userspace in order of allocation instead of order of transmission. This
usually doesn't matter since the order is either not determinable by
userspace or message creation/transmission is serialized. The only case
where this can have a visible difference is nfnetlink_queue. Userspace
can't assume mmap'ed messages have ordered IDs anymore and needs to check
this if using batched verdicts.
For non-mapped sockets, nothing changes.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helper functions for looking up mmap'ed frame headers, reading and
writing their status, allocating skbs with mmap'ed data areas and a poll
function.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a function to allocate a sk_buff head without any data. This will
be used by memory mapped netlink to attach data from the mmaped area
to the skb.
Additionally change skb_release_all() to check whether the skb has a
data area to allow the skb destructor to clear the data pointer in case
only a head has been allocated.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Memory mapped netlink needs to store the receiving userspace socket
when sending from the kernel to userspace. Rename 'ssk' to 'sk' to
avoid confusion.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for 802.1ad VLAN devices. This mainly consists of checking for
ETH_P_8021AD in addition to ETH_P_8021Q in a couple of places and check
offloading capabilities based on the used protocol.
Configuration is done using "ip link":
# ip link add link eth0 eth0.1000 \
type vlan proto 802.1ad id 1000
# ip link add link eth0.1000 eth0.1000.1000 \
type vlan proto 802.1q id 1000
52:54:00:12:34:56 > 92:b1:54:28:e4:8c, ethertype 802.1Q (0x8100), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto ICMP (1), length 84)
20.1.0.2 > 20.1.0.1: ICMP echo request, id 3003, seq 8, length 64
92:b1:54:28:e4:8c > 52:54:00:12:34:56, ethertype 802.1Q-QinQ (0x88a8), length 106: vlan 1000, p 0, ethertype 802.1Q, vlan 1000, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 47944, offset 0, flags [none], proto ICMP (1), length 84)
20.1.0.1 > 20.1.0.2: ICMP echo reply, id 3003, seq 8, length 64
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the encapsulation protocol value a property of VLAN devices and change
the device lookup functions to take the protocol value into account.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch
Jesse Gross says:
====================
A number of improvements for net-next/3.10.
Highlights include:
* Properly exposing linux/openvswitch.h to userspace after the uapi
changes.
* Simplification of locking. It immediately makes things simpler to
reason about and avoids holding RTNL mutex for longer than
necessary. In the near future it will also enable tunnel
registration and more fine-grained locking.
* Miscellaneous cleanups and simplifications.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add option to at86rf230 platform data to configure the type of the
interrupt used by the driver. The irq polarity of the device will
be configured accordingly.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation of dev_uc_sync/unsync() assumes that there is
a strict 1-to-1 relationship between the source and destination of the sync.
In other words, once an address has been synced to a destination device, it
will not be synced to any other device through the sync API.
However, there are some virtual devices that aggreate a number of lower
devices and need to sync addresses to all of them. The current
API falls short there.
This patch introduces a new dev_uc_sync_multiple() api that can be called
in the above circumstances and allows sync to work for every invocation.
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The link change is detected via the interrupt pipe, and bulk
pipes are responsible for transfering packets, so it is reasonable
to stop bulk transfer after link is reported as off.
Two adavantages may be obtained with stopping bulk transfer
after link becomes off:
- USB bus bandwidth is saved(USB bus is shared bus except for
USB3.0), for example, lots of 'IN' token packets and 'NYET'
handshake packets is transfered on 2.0 bus.
- probabaly power might be saved for usb host controller since
cancelling bulk transfer may disable the asynchronous schedule of
host controller.
With this patch, when link becomes off, about ~10% performance
boost can be found on bulk transfer of anther usb device which
is attached to same bus with the usbnet device, see below
test on next-20130410:
- read from usb mass storage(Sandisk Extreme USB 3.0) on pandaboard
with below command after unplugging ethernet cable:
dd if=/dev/sda iflag=direct of=/dev/null bs=1M count=800
- without the patch
1, 838860800 bytes (839 MB) copied, 36.2216 s, 23.2 MB/s
2, 838860800 bytes (839 MB) copied, 35.8368 s, 23.4 MB/s
3, 838860800 bytes (839 MB) copied, 35.823 s, 23.4 MB/s
4, 838860800 bytes (839 MB) copied, 35.937 s, 23.3 MB/s
5, 838860800 bytes (839 MB) copied, 35.7365 s, 23.5 MB/s
average: 23.6MB/s
- with the patch
1, 838860800 bytes (839 MB) copied, 32.3817 s, 25.9 MB/s
2, 838860800 bytes (839 MB) copied, 31.7389 s, 26.4 MB/s
3, 838860800 bytes (839 MB) copied, 32.438 s, 25.9 MB/s
4, 838860800 bytes (839 MB) copied, 32.5492 s, 25.8 MB/s
5, 838860800 bytes (839 MB) copied, 31.6178 s, 26.5 MB/s
average: 26.1MB/s
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces the API of usbnet_link_change, so that
usbnet can handle link change centrally, which may help to
implement killing traffic URBs for saving USB bus bandwidth
and host controller power.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/rt2x00/rt2x00pci.c
net/mac80211/sta_info.c
net/wireless/core.h
|
|
This patch introduces an UAPI header for the SCTP protocol,
so that we can facilitate the maintenance and development of
user land applications or libraries, in particular in terms
of header synchronization.
To not break compatibility, some fragments from lksctp-tools'
netinet/sctp.h have been carefully included, while taking care
that neither kernel nor user land breaks, so both compile fine
with this change (for lksctp-tools I tested with the old
netinet/sctp.h header and with a newly adapted one that includes
the uapi sctp header). lksctp-tools smoke test run through
successfully as well in both cases.
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable the DCB ETS ops only when supported by the firmware. For older firmware/cards
which don't support ETS, advertize only PFC DCB ops.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter and IPVS updates for
your net-next tree, most relevantly they are:
* Add net namespace support to NFLOG, ULOG and ebt_ulog and NFQUEUE.
The LOG and ebt_log target has been also adapted, but they still
depend on the syslog netnamespace that seems to be missing, from
Gao Feng.
* Don't lose indications of congestion in IPv6 fragmentation handling,
from Hannes Frederic Sowa.i
* IPVS conversion to use RCU, including some code consolidation patches
and optimizations, also some from Julian Anastasov.
* cpu fanout support for NFQUEUE, from Holger Eitzenberger.
* Better error reporting to userspace when dropping packets from
all our _*_[xfrm|route]_me_harder functions, from Patrick McHardy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix erroneous sock_orphan() leading to crashes and double
kfree_skb() in NFC protocol. From Thierry Escande and Samuel Ortiz.
2) Fix use after free in remain-on-channel mac80211 code, from Johannes
Berg.
3) nf_reset() needs to reset the NF tracing cookie, otherwise we can
leak it from one namespace into another. Fix from Gao Feng and
Patrick McHardy.
4) Fix overflow in channel scanning array of mwifiex driver, from Stone
Piao.
5) Fix loss of link after suspend/shutdown in r8169, from Hayes Wang.
6) Synchronization of unicast address lists to the undelying device
doesn't work because whether to sync is maintained as a boolean
rather than a true count. Fix from Vlad Yasevich.
7) Fix corruption of TSO packets in atl1e by limiting the segmented
packet length. From Hannes Frederic Sowa.
8) Revert bogus AF_UNIX credential passing change and fix the
coalescing issue properly, from Eric W Biederman.
9) Changes of ipv4 address lifetime settings needs to generate a
notification, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
netfilter: don't reset nf_trace in nf_reset()
net: ipv4: notify when address lifetime changes
ixgbe: fix registration order of driver and DCA nofitication
af_unix: If we don't care about credentials coallesce all messages
Revert "af_unix: dont send SCM_CREDENTIAL when dest socket is NULL"
bonding: remove sysfs before removing devices
atl1e: limit gso segment size to prevent generation of wrong ip length fields
net: count hw_addr syncs so that unsync works properly.
r8169: fix auto speed down issue
netfilter: ip6t_NPT: Fix translation for non-multiple of 32 prefix lengths
mwifiex: limit channel number not to overflow memory
NFC: microread: Fix build failure due to a new MEI bus API
iwlwifi: dvm: fix the passive-no-RX workaround
netfilter: nf_conntrack: fix error return code
NFC: llcp: Keep the connected socket parent pointer alive
mac80211: fix idle handling sequence
netfilter: nfnetlink_acct: return -EINVAL if object name is empty
netfilter: nfnetlink_queue: fix error return code in nfnetlink_queue_init()
netfilter: reset nf_trace in nf_reset
mac80211: fix remain-on-channel cancel crash
...
|
|
Commit 130549fe ("netfilter: reset nf_trace in nf_reset") added code
to reset nf_trace in nf_reset(). This is wrong and unnecessary.
nf_reset() is used in the following cases:
- when passing packets up the the socket layer, at which point we want to
release all netfilter references that might keep modules pinned while
the packet is queued. nf_trace doesn't matter anymore at this point.
- when encapsulating or decapsulating IPsec packets. We want to continue
tracing these packets after IPsec processing.
- when passing packets through virtual network devices. Only devices on
that encapsulate in IPv4/v6 matter since otherwise nf_trace is not
used anymore. Its not entirely clear whether those packets should
be traced after that, however we've always done that.
- when passing packets through virtual network devices that make the
packet cross network namespace boundaries. This is the only cases
where we clearly want to reset nf_trace and is also what the
original patch intended to fix.
Add a new function nf_reset_trace() and use it in dev_forward_skb() to
fix this properly.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that this supports net namespace for nflog and nfqueue,
we can remove the global proc_net_netfilter which has no
clients anymore.
Based on patch from Gao feng.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
A few drivers use dev_uc_sync/unsync to synchronize the
address lists from master down to slave/lower devices. In
some cases (bond/team) a single address list is synched down
to multiple devices. At the time of unsync, we have a leak
in these lower devices, because "synced" is treated as a
boolean and the address will not be unsynced for anything after
the first device/call.
Treat "synced" as a count (same as refcount) and allow all
unsync calls to work.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Revert of a recent cpuidle change that caused Nehalem machines to
hang on boot from Alex Shi.
- USB power management fix addressing a crash in the port device
object's release routine from Rafael J Wysocki.
- Device PM QoS fix for a potential deadlock related to sysfs interface
from Rafael J Wysocki.
- Fix for a cpufreq crash when the /cpus Device Tree node is missing
from Paolo Pisati.
- Fix for a build issue on ia64 related to the Boot Graphics Resource
Table (BGRT) from Tony Luck.
- Two fixes for ACPI handles being set incorrectly for device objects
that don't correspond to any ACPI namespace nodes in the I2C and SPI
subsystems from Rafael J Wysocki.
- Fix for compiler warnings related to CONFIG_PM_DEVFREQ being unset
from Rajagopal Venkat.
- Fix for a symbol definition typo in cpufreq_governor.h from Borislav
Petkov.
* tag 'pm+acpi-3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / BGRT: Don't let users configure BGRT on non X86 systems
cpuidle / ACPI: recover percpu ACPI processor cstate
ACPI / I2C: Use parent's ACPI_HANDLE() in acpi_i2c_register_devices()
cpufreq: Correct header guards typo
ACPI / SPI: Use parent's ACPI_HANDLE() in acpi_register_spi_devices()
cpufreq: check OF node /cpus presence before dereferencing it
PM / devfreq: Fix compiler warnings for CONFIG_PM_DEVFREQ unset
PM / QoS: Avoid possible deadlock related to sysfs access
USB / PM: Don't try to hide PM QoS flags from usb_port_device_release()
|
|
Pablo Neira Ayuso says:
====================
The following patchset contains netfilter updates for your net tree,
they are:
* Fix missing the skb->trace reset in nf_reset, noticed by Gao Feng
while using the TRACE target with several net namespaces.
* Fix prefix translation in IPv6 NPT if non-multiple of 32 prefixes
are used, from Matthias Schiffer.
* Fix invalid nfacct objects with empty name, they are now rejected
with -EINVAL, spotted by Michael Zintakis, patch from myself.
* A couple of fixes for wrong return values in the error path of
nfnetlink_queue and nf_conntrack, from Wei Yongjun.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull net into net-next to get the synchronize_net() bug fix in
bonding.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MIPS fixes from Ralf Baechle:
"A collection of fixes pretty much across the MIPS code. Even the
change to include/linux/signal.h by David Howells' 2a1486981c13 ("Fix
breakage in MIPS siginfo handling") should be considered MIPS-specific
as it touches an ifdefed segment that is only relevant to MIPS and
which unfortunately can't be made to go away entirely."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
Fix breakage in MIPS siginfo handling
Revert "MIPS: BCM63XX: Call board_register_device from device_initcall()"
MIPS: BCM63XX: Make nvram checksum failure non fatal
MIPS: Fix code generation for non-DSP capable CPUs
MIPS: Fix inconsistent formatting inside /proc/cpuinfo
MIPS: SEAD3: Enable LL/SC.
MIPS: Get rid of CONFIG_CPU_HAS_LLSC again
MIPS: Add dependencies for HAVE_ARCH_TRANSPARENT_HUGEPAGE
MIPS: VR4133: Fix probe for LL/SC.
MIPS: Fix logic errors in bitops.c
MIPS: Use CONFIG_CPU_MIPSR2 in csum_partial.S
MIPS: compat: Return same error ENOSYS as native for invalid operation.
|
|
of_get_mac_address() and of_get_phy_mode() are only provided if OF_NET
is configured. While most callers check for the define, not all do, and those
who do require #ifdef around the code. For those who don't, the missing check
can result in errors such as
arch/powerpc/sysdev/tsi108_dev.c:107:3: error: implicit declaration of
function 'of_get_mac_address' [-Werror=implicit-function-declaration]
arch/powerpc/sysdev/mv64x60_dev.c:253:2: error: implicit declaration of
function 'of_get_mac_address' [-Werror=implicit-function-declaration]
Provide empty functions if OF_NET is not configured.
This is safe because all callers do check the return values.
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix compiler warnings generated when devfreq is not enabled
(CONFIG_PM_DEVFREQ is not set).
Signed-off-by: Rajagopal Venkat <rajagopal.venkat@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rename skb_dst_set_noref to __skb_dst_set_noref and
add force flag as suggested by David Miller. The new wrapper
skb_dst_set_noref_force will force dst entries that are not
cached to be attached as skb dst without taking reference
as long as provided dst is reclaimed after RCU grace period.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) sadb_msg prepared for IPSEC userspace forgets to initialize the
satype field, fix from Nicolas Dichtel.
2) Fix mac80211 synchronization during station removal, from Johannes
Berg.
3) Fix IPSEC sequence number notifications when they wrap, from Steffen
Klassert.
4) Fix cfg80211 wdev tracing crashes when add_virtual_intf() returns an
error pointer, from Johannes Berg.
5) In mac80211, don't call into the channel context code with the
interface list mutex held. From Johannes Berg.
6) In mac80211, if we don't actually associate, do not restart the STA
timer, otherwise we can crash. From Ben Greear.
7) Missing dma_mapping_error() check in e1000, ixgb, and e1000e. From
Christoph Paasch.
8) Fix sja1000 driver defines to not conflict with SH port, from Marc
Kleine-Budde.
9) Don't call il4965_rs_use_green with a NULL station, from Colin Ian
King.
10) Suspend/Resume in the FEC driver fail because the buffer descriptors
are not initialized at all the moments in which they should. Fix
from Frank Li.
11) cpsw and davinci_emac drivers both use the wrong interface to
restart a stopped TX queue. Use netif_wake_queue not
netif_start_queue, the latter is for initialization/bringup not
active management of the queue. From Mugunthan V N.
12) Fix regression in rate calculations done by
psched_ratecfg_precompute(), missing u64 type promotion. From
Sergey Popovich.
13) Fix length overflow in tg3 VPD parsing, from Kees Cook.
14) AOE driver fails to allocate enough headroom, resulting in crashes.
Fix from Eric Dumazet.
15) RX overflow happens too quickly in sky2 driver because pause packet
thresholds are not programmed correctly. From Mirko Lindner.
16) Bonding driver manages arp_interval and miimon settings incorrectly,
disabling one unintentionally disables both. Fix from Nikolay
Aleksandrov.
17) smsc75xx drivers don't program the RX mac properly for jumbo frames.
Fix from Steve Glendinning.
18) Fix off-by-one in Codel packet scheduler. From Vijay Subramanian.
19) Fix packet corruption in atl1c by disabling MSI support, from Hannes
Frederic Sowa.
20) netdev_rx_handler_unregister() needs a synchronize_net() to fix
crashes in bonding driver unload stress tests. From Eric Dumazet.
21) rxlen field of ks8851 RX packet descriptors not interpreted
correctly (it is 12 bits not 16 bits, so needs to be masked after
shifting the 32-bit value down 16 bits). Fix from Max Nekludov.
22) Fix missed RX/TX enable in sh_eth driver due to mishandling of link
change indications. From Sergei Shtylyov.
23) Fix crashes during spurious ECI interrupts in sh_eth driver, also
from Sergei Shtylyov.
24) dm9000 driver initialization is done wrong for revision B devices
with DSP PHY, from Joseph CHANG.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
DM9000B: driver initialization upgrade
sh_eth: make 'link' field of 'struct sh_eth_private' *int*
sh_eth: workaround for spurious ECI interrupt
sh_eth: fix handling of no LINK signal
ks8851: Fix interpretation of rxlen field.
net: add a synchronize_net() in netdev_rx_handler_unregister()
MAINTAINERS: Update netxen_nic maintainers list
atl1e: drop pci-msi support because of packet corruption
net: fq_codel: Fix off-by-one error
net: calxedaxgmac: Wake-on-LAN fixes
net: calxedaxgmac: fix rx ring handling when OOM
net: core: Remove redundant call to 'nf_reset' in 'dev_forward_skb'
smsc75xx: fix jumbo frame support
net: fix the use of this_cpu_ptr
bonding: fix disabling of arp_interval and miimon
ipv6: don't accept node local multicast traffic from the wire
sky2: Threshold for Pause Packet is set wrong
sky2: Receive Overflows not counted
aoe: reserve enough headroom on skbs
line up comment for ndo_bridge_getlink
...
|
|
This reverts commit 6aa9707099c4b25700940eb3d016f16c4434360d.
Commit 6aa9707099c4 ("lockdep: check that no locks held at freeze time")
causes problems with NFS root filesystems. The failures were noticed on
OMAP2 and 3 boards during kernel init:
[ BUG: swapper/0/1 still has locks held! ]
3.9.0-rc3-00344-ga937536 #1 Not tainted
-------------------------------------
1 lock held by swapper/0/1:
#0: (&type->s_umount_key#13/1){+.+.+.}, at: [<c011e84c>] sget+0x248/0x574
stack backtrace:
rpc_wait_bit_killable
__wait_on_bit
out_of_line_wait_on_bit
__rpc_execute
rpc_run_task
rpc_call_sync
nfs_proc_get_root
nfs_get_root
nfs_fs_mount_common
nfs_try_mount
nfs_fs_mount
mount_fs
vfs_kern_mount
do_mount
sys_mount
do_mount_root
mount_root
prepare_namespace
kernel_init_freeable
kernel_init
Although the rootfs mounts, the system is unstable. Here's a transcript
from a PM test:
http://www.pwsan.com/omap/testlogs/test_v3.9-rc3/20130317194234/pm/37xxevm/37xxevm_log.txt
Here's what the test log should look like:
http://www.pwsan.com/omap/testlogs/test_v3.8/20130218214403/pm/37xxevm/37xxevm_log.txt
Mailing list discussion is here:
http://lkml.org/lkml/2013/3/4/221
Deal with this for v3.9 by reverting the problem commit, until folks can
figure out the right long-term course of action.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: <maciej.rutecki@gmail.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ben Chan <benchan@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As time passed, some fields were added in net_device, and not
at sensible offsets.
Lets reorder some fields to reduce number of cache lines in RX path.
Fields not used in data path should be moved out of this critical cache
line.
In particular, move broadcast[] to the end of the rx section,
as it is less used, and ethernet uses only the beginning of the 32bytes
field.
Before patch :
offsetof(struct net_device,dev_addr)=0x258
offsetof(struct net_device,rx_handler)=0x2b8
offsetof(struct net_device,ingress_queue)=0x2c8
offsetof(struct net_device,broadcast)=0x278
After :
offsetof(struct net_device,dev_addr)=0x280
offsetof(struct net_device,rx_handler)=0x298
offsetof(struct net_device,ingress_queue)=0x2a8
offsetof(struct net_device,broadcast)=0x2b0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for make V=1 EXTRA_CFLAGS=-W ARCH=arm allmodconfig
printk is need when CONFIG_BPF_JIT is defined
or it will report pr_err and print_hex_dump are implicit declaration
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It contains the public netlink interface bits required by userspace to
make use of the interface.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Commit d0418bb7123f44b23d69ac349eec7daf9103472f (net: sh_eth: Add eth support
for R8A7779 device) was a failed attempt to add support for one of members of
the R-Car SoC family. That's for three reasons: it treated R8A7779 the same
as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask
in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in
R-Car Ether), and it didn't add a new register offset array despite the closest
SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether
registers have, and also some of the registers in this old mapping don't exist
on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not
adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724
related section to its pristine state...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
programs"
This reverts commit 186930500985 ("mm: introduce VM_POPULATE flag to
better deal with racy userspace programs").
VM_POPULATE only has any effect when userspace plays racy games with
vmas by trying to unmap and remap memory regions that mmap or mlock are
operating on.
Also, the only effect of VM_POPULATE when userspace plays such games is
that it avoids populating new memory regions that get remapped into the
address range that was being operated on by the original mmap or mlock
calls.
Let's remove VM_POPULATE as there isn't any strong argument to mandate a
new vm_flag.
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some USB fixes to resolve issues reported recently, as well
as a new device id for the ftdi_sio driver."
* tag 'usb-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
usb: Fix compile error by selecting USB_OTG_UTILS
USB: serial: fix hang when opening port
USB: EHCI: fix bug in iTD/siTD DMA pool allocation
xhci: Don't warn on empty ring for suspended devices.
usb: xhci: Fix TRB transfer length macro used for Event TRB.
usb/acpi: binding xhci root hub usb port with ACPI
usb: add find_raw_port_number callback to struct hc_driver()
usb: xhci: fix build warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are some small char/misc driver fixes that resolve issues
recently reported against the 3.9-rc kernels. All have been in
linux-next for a while."
* tag 'char-misc-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
VMCI: Fix process-to-process DRGAMs.
mei: ME hardware reset needs to be synchronized
mei: add mei_stop function to stop mei device
extcon: max77693: Initialize register of MUIC device to bring up it without platform data
extcon: max77693: Fix bug of wrong pointer when platform data is not used
extcon: max8997: Check the pointer of platform data to protect null pointer error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull userns fixes from Eric W Biederman:
"The bulk of the changes are fixing the worst consequences of the user
namespace design oversight in not considering what happens when one
namespace starts off as a clone of another namespace, as happens with
the mount namespace.
The rest of the changes are just plain bug fixes.
Many thanks to Andy Lutomirski for pointing out many of these issues."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
userns: Restrict when proc and sysfs can be mounted
ipc: Restrict mounting the mqueue filesystem
vfs: Carefully propogate mounts across user namespaces
vfs: Add a mount flag to lock read only bind mounts
userns: Don't allow creation if the user is chrooted
yama: Better permission check for ptraceme
pid: Handle the exit of a multi-threaded init.
scm: Require CAP_SYS_ADMIN over the current pidns to spoof pids.
|
|
Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.
Also update all the users of this value that David Miller and
I could find to use the new constant.
Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.
As suggested by Jesse Gross.
Compile tested only.
Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tokenring support was deleted in v3.5. One last holdout of the macro
CONFIG_TR escaped that fate. Until now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 40893fd(net: switch to use skb_probe_transport_header())
involes a new error accidently. When NET_SKBUFF_DATA_USES_OFFSE is
not enabled, below compile error happens:
CC net/packet/af_packet.o
net/packet/af_packet.c: In function ‘packet_sendmsg_spkt’:
net/packet/af_packet.c:1516:2: error: implicit declaration of function ‘skb_probe_transport_header’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [net/packet/af_packet.o] Error 1
make[1]: *** [net/packet] Error 2
make: *** [net] Error 2
As it seems skb_probe_transport_header() is not related to
NET_SKBUFF_DATA_USES_OFFSE, we should move the definition of
skb_probe_transport_header() out of scope of
NET_SKBUFF_DATA_USES_OFFSE macro.
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
include/net/ipip.h
The changes made to ipip.h in 'net' were already included
in 'net-next' before that header was moved to another location.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function will be used by brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add some more chip IDs to bcma_pmu_get_alp_clock()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Sometimes, we need probe and set the transport header for packets (e.g from
untrusted source). This patch introduces a new helper
skb_probe_transport_header() which tries to probe and set the l4 header through
skb_flow_dissect(), if not just set the transport header to the hint passed by
caller.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
