| Age | Commit message (Collapse) | Author |
|---|
|
commit 1e77d0a1ed7417d2a5a52a7b8d32aea1833faa6c upstream.
Till reported that the spurious interrupt detection of threaded
interrupts is broken in two ways:
- note_interrupt() is called for each action thread of a shared
interrupt line. That's wrong as we are only interested whether none
of the device drivers felt responsible for the interrupt, but by
calling multiple times for a single interrupt line we account
IRQ_NONE even if one of the drivers felt responsible.
- note_interrupt() when called from the thread handler is not
serialized. That leaves the members of irq_desc which are used for
the spurious detection unprotected.
To solve this we need to defer the spurious detection of a threaded
interrupt to the next hardware interrupt context where we have
implicit serialization.
If note_interrupt is called with action_ret == IRQ_WAKE_THREAD, we
check whether the previous interrupt requested a deferred check. If
not, we request a deferred check for the next hardware interrupt and
return.
If set, we check whether one of the interrupt threads signaled
success. Depending on this information we feed the result into the
spurious detector.
If one primary handler of a shared interrupt returns IRQ_HANDLED we
disable the deferred check of irq threads on the same line, as we have
found at least one device driver who cared.
Reported-by: Till Straumann <strauman@slac.stanford.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Austin Schuh <austin@peloton-tech.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-can@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1303071450130.22263@ionos
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 45fef5b88d1f2f47ecdefae6354372d440ca5c84 upstream.
Commit 1a699476e258 ("ACPI / hotplug / PCI: Hotplug notifications
from acpi_bus_notify()") added debug messages for a few common
events. These debug messages are unconditionally enabled if
CONFIG_DYNAMIC_DEBUG is defined, contrary to the documented
meaning, making the ACPI system spew lots of unwanted noise on
any kernel with dynamic debugging.
The bug was introduced by commit fbfddae69657 ("ACPI: Add
acpi_handle_<level>() interfaces"), which added the
CONFIG_DYNAMIC_DEBUG dependency without respecting its meaning.
Fix by adding real support for dynamic_debug.
Fixes: fbfddae69657 ("ACPI: Add acpi_handle_<level>() interfaces")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c8349a17137b93f0a83f276c764a6df1b9a116e upstream.
When we perform a data integrity sync we tag all the dirty pages with
PAGECACHE_TAG_TOWRITE at start of ext4_da_writepages. Later we check
for this tag in write_cache_pages_da and creates a struct
mpage_da_data containing contiguously indexed pages tagged with this
tag and sync these pages with a call to mpage_da_map_and_submit. This
process is done in while loop until all the PAGECACHE_TAG_TOWRITE
pages are synced. We also do journal start and stop in each iteration.
journal_stop could initiate journal commit which would call
ext4_writepage which in turn will call ext4_bio_write_page even for
delayed OR unwritten buffers. When ext4_bio_write_page is called for
such buffers, even though it does not sync them but it clears the
PAGECACHE_TAG_TOWRITE of the corresponding page and hence these pages
are also not synced by the currently running data integrity sync. We
will end up with dirty pages although sync is completed.
This could cause a potential data loss when the sync call is followed
by a truncate_pagecache call, which is exactly the case in
collapse_range. (It will cause generic/127 failure in xfstests)
To avoid this issue, we can use set_page_writeback_keepwrite instead of
set_page_writeback, which doesn't clear TOWRITE tag.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e52365f279564cef0ddd41db5237f0471381093 upstream.
When tracing a process in another pid namespace, it's important for fork
event messages to contain the child's pid as seen from the tracer's pid
namespace, not the parent's. Otherwise, the tracer won't be able to
correlate the fork event with later SIGTRAP signals it receives from the
child.
We still risk a race condition if a ptracer from a different pid
namespace attaches after we compute the pid_t value. However, sending a
bogus fork event message in this unlikely scenario is still a vast
improvement over the status quo where we always send bogus fork event
messages to debuggers in a different pid namespace than the forking
process.
Signed-off-by: Matthew Dempsky <mdempsky@chromium.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Julien Tinnes <jln@chromium.org>
Cc: Roland McGrath <mcgrathr@chromium.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e58469bafd0524e848c3733bc3918d854595e20f upstream.
The test_bit operations in get/set pageblock flags are expensive. This
patch reads the bitmap on a word basis and use shifts and masks to isolate
the bits of interest. Similarly masks are used to set a local copy of the
bitmap and then use cmpxchg to update the bitmap if there have been no
other changes made in parallel.
In a test running dd onto tmpfs the overhead of the pageblock-related
functions went from 1.27% in profiles to 0.5%.
In addition to the performance benefits, this patch closes races that are
possible between:
a) get_ and set_pageblock_migratetype(), where get_pageblock_migratetype()
reads part of the bits before and other part of the bits after
set_pageblock_migratetype() has updated them.
b) set_pageblock_migratetype() and set_pageblock_skip(), where the non-atomic
read-modify-update set bit operation in set_pageblock_skip() will cause
lost updates to some bits changed in the set_pageblock_migratetype().
Joonsoo Kim first reported the case a) via code inspection. Vlastimil
Babka's testing with a debug patch showed that either a) or b) occurs
roughly once per mmtests' stress-highalloc benchmark (although not
necessarily in the same pageblock). Furthermore during development of
unrelated compaction patches, it was observed that frequent calls to
{start,undo}_isolate_page_range() the race occurs several thousands of
times and has resulted in NULL pointer dereferences in move_freepages()
and free_one_page() in places where free_list[migratetype] is
manipulated by e.g. list_move(). Further debugging confirmed that
migratetype had invalid value of 6, causing out of bounds access to the
free_list array.
That confirmed that the race exist, although it may be extremely rare,
and currently only fatal where page isolation is performed due to
memory hot remove. Races on pageblocks being updated by
set_pageblock_migratetype(), where both old and new migratetype are
lower MIGRATE_RESERVE, currently cannot result in an invalid value
being observed, although theoretically they may still lead to
unexpected creation or destruction of MIGRATE_RESERVE pageblocks.
Furthermore, things could get suddenly worse when memory isolation is
used more, or when new migratetypes are added.
After this patch, the race has no longer been observed in testing.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c177c81e09e517bbf75b67762cdab1b83aba6976 upstream.
Currently hugepage migration is available for all archs which support
pmd-level hugepage, but testing is done only for x86_64 and there're
bugs for other archs. So to avoid breaking such archs, this patch
limits the availability strictly to x86_64 until developers of other
archs get interested in enabling this feature.
Simply disabling hugepage migration on non-x86_64 archs is not enough to
fix the reported problem where sys_move_pages() hits the BUG_ON() in
follow_page(FOLL_GET), so let's fix this by checking if hugepage
migration is supported in vma_migratable().
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9d0d68faea6962d62dd501cd6e71ce5cc8ed262b ]
Now it is not possible to set mtu to team device which has a port
enslaved to it. The reason is that when team_change_mtu() calls
dev_set_mtu() for port device, notificator for NETDEV_PRECHANGEMTU
event is called and team_device_event() returns NOTIFY_BAD forbidding
the change. So fix this by returning NOTIFY_DONE here in case team is
changing mtu in team_change_mtu().
Introduced-by: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2d7a85f4b06e9c27ff629f07a524c48074f07f81 ]
It was possible to get a setuid root or setcap executable to write to
it's stdout or stderr (which has been set made a netlink socket) and
inadvertently reconfigure the networking stack.
To prevent this we check that both the creator of the socket and
the currentl applications has permission to reconfigure the network
stack.
Unfortunately this breaks Zebra which always uses sendto/sendmsg
and creates it's socket without any privileges.
To keep Zebra working don't bother checking if the creator of the
socket has privilege when a destination address is specified. Instead
rely exclusively on the privileges of the sender of the socket.
Note from Andy: This is exactly Eric's code except for some comment
clarifications and formatting fixes. Neither I nor, I think, anyone
else is thrilled with this approach, but I'm hesitant to wait on a
better fix since 3.15 is almost here.
Note to stable maintainers: This is a mess. An earlier series of
patches in 3.15 fix a rather serious security issue (CVE-2014-0181),
but they did so in a way that breaks Zebra. The offending series
includes:
commit aa4cf9452f469f16cea8c96283b641b4576d4a7b
Author: Eric W. Biederman <ebiederm@xmission.com>
Date: Wed Apr 23 14:28:03 2014 -0700
net: Add variants of capable for use on netlink messages
If a given kernel version is missing that series of fixes, it's
probably worth backporting it and this patch. if that series is
present, then this fix is critical if you care about Zebra.
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aa4cf9452f469f16cea8c96283b641b4576d4a7b ]
netlink_net_capable - The common case use, for operations that are safe on a network namespace
netlink_capable - For operations that are only known to be safe for the global root
netlink_ns_capable - The general case of capable used to handle special cases
__netlink_ns_capable - Same as netlink_ns_capable except taking a netlink_skb_parms instead of
the skbuff of a netlink message.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a53b72c83a4216f2eb883ed45a0cbce014b8e62d ]
The permission check in sock_diag_put_filterinfo is wrong, and it is so removed
from it's sources it is not clear why it is wrong. Move the computation
into packet_diag_dump and pass a bool of the result into sock_diag_filterinfo.
This does not yet correct the capability check but instead simply moves it to make
it clear what is going on.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 23adbe12ef7d3d4195e80800ab36b37bee28cd03 upstream.
The kernel has no concept of capabilities with respect to inodes; inodes
exist independently of namespaces. For example, inode_capable(inode,
CAP_LINUX_IMMUTABLE) would be nonsense.
This patch changes inode_capable to check for uid and gid mappings and
renames it to capable_wrt_inode_uidgid, which should make it more
obvious what it does.
Fixes CVE-2014-4014.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c36b390a546055b6815d4b93a2c9fed4d980ffb upstream.
The percpu-refcount infrastructure uses the underscore variants of
this_cpu_ops in order to modify percpu reference counters.
(e.g. __this_cpu_inc()).
However the underscore variants do not atomically update the percpu
variable, instead they may be implemented using read-modify-write
semantics (more than one instruction). Therefore it is only safe to
use the underscore variant if the context is always the same (process,
softirq, or hardirq). Otherwise it is possible to lose updates.
This problem is something that Sebastian has seen within the aio
subsystem which uses percpu refcounters both in process and softirq
context leading to reference counts that never dropped to zeroes; even
though the number of "get" and "put" calls matched.
Fix this by using the non-underscore this_cpu_ops variant which
provides correct per cpu atomic semantics and fixes the corrupted
reference counts.
Cc: Kent Overstreet <kmo@daterainc.com>
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
References: http://lkml.kernel.org/g/alpine.LFD.2.11.1406041540520.21183@denkbrett
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1f43dd9c20d85e66c4d77e284f64ac114abe3f8 upstream.
The count which is used to get_unmap_data maybe not the same as the
count computed in dmaengine_unmap which causes to free data in a
wrong pool.
This patch fixes this issue by keeping the map count with unmap_data
structure and use this count to get the pool.
Signed-off-by: Xuelin Shi <xuelin.shi@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4c88d7f9b0d5fb0588c3386be62115cc2eaa8f9f upstream.
Patch 01f8fa4f01d "genirq: Allow forcing cpu affinity of interrupts" added
an irq_force_affinity() function, and 30ccf03b4a6 "clocksource: Exynos_mct:
Use irq_force_affinity() in cpu bringup" subsequently uses it. However, the
driver can be used with CONFIG_SMP disabled, but the function declaration
is only available for CONFIG_SMP, leading to this build error:
drivers/clocksource/exynos_mct.c:431:3: error: implicit declaration of function 'irq_force_affinity' [-Werror=implicit-function-declaration]
irq_force_affinity(mct_irqs[MCT_L0_IRQ + cpu], cpumask_of(cpu));
This patch introduces a dummy helper function for the non-SMP case
that always returns success, to get rid of the build error.
Since the patches causing the problem are marked for stable backports,
this one should be as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Link: http://lkml.kernel.org/r/5619084.0zmrrIUZLV@wuerfel
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0456c66f4e905e1ca839318219c770988b47975c upstream.
serio devices exposed via platform firmware interfaces such as ACPI may
provide additional identifying information of use to userspace.
We don't associate the serio devices with the firmware device (we don't
set it as parent), so there's no way for userspace to make use of this
information.
We cannot change the parent for serio devices instantiated though a
firmware interface as that would break suspend / resume ordering.
Therefore this patch adds a new firmware_id sysfs attribute so that
userspace can get a string from there with any additional identifying
information the firmware interface may provide.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 01f8fa4f01d8362358eb90e412bd7ae18a3ec1ad upstream.
The current implementation of irq_set_affinity() refuses rightfully to
route an interrupt to an offline cpu.
But there is a special case, where this is actually desired. Some of
the ARM SoCs have per cpu timers which require setting the affinity
during cpu startup where the cpu is not yet in the online mask.
If we can't do that, then the local timer interrupt for the about to
become online cpu is routed to some random online cpu.
The developers of the affected machines tried to work around that
issue, but that results in a massive mess in that timer code.
We have a yet unused argument in the set_affinity callbacks of the irq
chips, which I added back then for a similar reason. It was never
required so it got not used. But I'm happy that I never removed it.
That allows us to implement a sane handling of the above scenario. So
the affected SoC drivers can add the required force handling to their
interrupt chip, switch the timer code to irq_force_affinity() and
things just work.
This does not affect any existing user of irq_set_affinity().
Tagged for stable to allow a simple fix of the affected SoC clock
event drivers.
Reported-and-tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Link: http://lkml.kernel.org/r/20140416143315.717251504@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ec36cafe43bf835f8f29273597a5b0cbc8267ef upstream.
Currently we get the following kind of errors if we try to use interrupt
phandles to irqchips that have not yet initialized:
irq: no irq domain found for /ocp/pinmux@48002030 !
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/of/platform.c:171 of_device_alloc+0x144/0x184()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.12.0-00038-g42a9708 #1012
(show_stack+0x14/0x1c)
(dump_stack+0x6c/0xa0)
(warn_slowpath_common+0x64/0x84)
(warn_slowpath_null+0x1c/0x24)
(of_device_alloc+0x144/0x184)
(of_platform_device_create_pdata+0x44/0x9c)
(of_platform_bus_create+0xd0/0x170)
(of_platform_bus_create+0x12c/0x170)
(of_platform_populate+0x60/0x98)
This is because we're wrongly trying to populate resources that are not
yet available. It's perfectly valid to create irqchips dynamically, so
let's fix up the issue by resolving the interrupt resources when
platform_get_irq is called.
And then we also need to accept the fact that some irqdomains do not
exist that early on, and only get initialized later on. So we can
make the current WARN_ON into just into a pr_debug().
We still attempt to populate irq resources when we create the devices.
This allows current drivers which don't use platform_get_irq to continue
to function. Once all drivers are fixed, this code can be removed.
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a949ae560a511fe4e3adf48fa44fefded93e5c2b upstream.
A race exists between module loading and enabling of function tracer.
CPU 1 CPU 2
----- -----
load_module()
module->state = MODULE_STATE_COMING
register_ftrace_function()
mutex_lock(&ftrace_lock);
ftrace_startup()
update_ftrace_function();
ftrace_arch_code_modify_prepare()
set_all_module_text_rw();
<enables-ftrace>
ftrace_arch_code_modify_post_process()
set_all_module_text_ro();
[ here all module text is set to RO,
including the module that is
loading!! ]
blocking_notifier_call_chain(MODULE_STATE_COMING);
ftrace_init_module()
[ tries to modify code, but it's RO, and fails!
ftrace_bug() is called]
When this race happens, ftrace_bug() will produces a nasty warning and
all of the function tracing features will be disabled until reboot.
The simple solution is to treate module load the same way the core
kernel is treated at boot. To hardcode the ftrace function modification
of converting calls to mcount into nops. This is done in init/main.c
there's no reason it could not be done in load_module(). This gives
a better control of the changes and doesn't tie the state of the
module to its notifiers as much. Ftrace is special, it needs to be
treated as such.
The reason this would work, is that the ftrace_module_init() would be
called while the module is in MODULE_STATE_UNFORMED, which is ignored
by the set_all_module_text_ro() call.
Link: http://lkml.kernel.org/r/1395637826-3312-1-git-send-email-indou.takao@jp.fujitsu.com
Reported-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 200b916f3575bdf11609cb447661b8d5957b0bbf ]
From: Cong Wang <cwang@twopensource.com>
commit 50624c934db18ab90 (net: Delay default_device_exit_batch until no
devices are unregistering) introduced rtnl_lock_unregistering() for
default_device_exit_batch(). Same race could happen we when rmmod a driver
which calls rtnl_link_unregister() as we call dev->destructor without rtnl
lock.
For long term, I think we should clean up the mess of netdev_run_todo()
and net namespce exit code.
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3d4405226d27b3a215e4d03cfa51f536244e5de7 ]
net_get_random_once depends on the static keys infrastructure to patch up
the branch to the slow path during boot. This was realized by abusing the
static keys api and defining a new initializer to not enable the call
site while still indicating that the branch point should get patched
up. This was needed to have the fast path considered likely by gcc.
The static key initialization during boot up normally walks through all
the registered keys and either patches in ideal nops or enables the jump
site but omitted that step on x86 if ideal nops where already placed at
static_key branch points. Thus net_get_random_once branches not always
became active.
This patch switches net_get_random_once to the ordinary static_key
api and thus places the kernel fast path in the - by gcc considered -
unlikely path. Microbenchmarks on Intel and AMD x86-64 showed that
the unlikely path actually beats the likely path in terms of cycle cost
and that different nop patterns did not make much difference, thus this
switch should not be noticeable.
Fixes: a48e42920ff38b ("net: introduce new macro net_get_random_once")
Reported-by: Tuomas Räsänen <tuomasjjrasanen@tjjr.fi>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 78541c1dc60b65ecfce5a6a096fc260219d6784e ]
The caller needs capabilities on the namespace being queried, not on
their own namespace. This is a security bug, although it likely has
only a minor impact.
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c674ac30c549596295eb0a5af7f4714c0b905b6f ]
Macvlan devices try to avoid stacking, but that's not always
successfull or even desired. As an example, the following
configuration is perefectly legal and valid:
eth0 <--- macvlan0 <---- vlan0.10 <--- macvlan1
However, this configuration produces the following lockdep
trace:
[ 115.620418] ======================================================
[ 115.620477] [ INFO: possible circular locking dependency detected ]
[ 115.620516] 3.15.0-rc1+ #24 Not tainted
[ 115.620540] -------------------------------------------------------
[ 115.620577] ip/1704 is trying to acquire lock:
[ 115.620604] (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[ 115.620686]
but task is already holding lock:
[ 115.620723] (&macvlan_netdev_addr_lock_key){+.....}, at: [<ffffffff815da5be>] dev_set_rx_mode+0x1e/0x40
[ 115.620795]
which lock already depends on the new lock.
[ 115.620853]
the existing dependency chain (in reverse order) is:
[ 115.620894]
-> #1 (&macvlan_netdev_addr_lock_key){+.....}:
[ 115.620935] [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[ 115.620974] [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[ 115.621019] [<ffffffffa07296c3>] vlan_dev_set_rx_mode+0x53/0x110 [8021q]
[ 115.621066] [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[ 115.621105] [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[ 115.621143] [<ffffffff815da6be>] __dev_open+0xde/0x140
[ 115.621174] [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[ 115.621174] [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[ 115.621174] [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[ 115.621174] [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[ 115.621174] [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[ 115.621174] [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[ 115.621174] [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[ 115.621174] [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[ 115.621174] [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[ 115.621174] [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[ 115.621174] [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[ 115.621174] [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[ 115.621174] [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[ 115.621174] [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b
[ 115.621174]
-> #0 (&vlan_netdev_addr_lock_key/1){+.....}:
[ 115.621174] [<ffffffff810d4d43>] __lock_acquire+0x1773/0x1a60
[ 115.621174] [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[ 115.621174] [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[ 115.621174] [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[ 115.621174] [<ffffffffa0696d2a>] macvlan_set_mac_lists+0xca/0x110 [macvlan]
[ 115.621174] [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[ 115.621174] [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[ 115.621174] [<ffffffff815da6be>] __dev_open+0xde/0x140
[ 115.621174] [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[ 115.621174] [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[ 115.621174] [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[ 115.621174] [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[ 115.621174] [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[ 115.621174] [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[ 115.621174] [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[ 115.621174] [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[ 115.621174] [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[ 115.621174] [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[ 115.621174] [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[ 115.621174] [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[ 115.621174] [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[ 115.621174] [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b
[ 115.621174]
other info that might help us debug this:
[ 115.621174] Possible unsafe locking scenario:
[ 115.621174] CPU0 CPU1
[ 115.621174] ---- ----
[ 115.621174] lock(&macvlan_netdev_addr_lock_key);
[ 115.621174] lock(&vlan_netdev_addr_lock_key/1);
[ 115.621174] lock(&macvlan_netdev_addr_lock_key);
[ 115.621174] lock(&vlan_netdev_addr_lock_key/1);
[ 115.621174]
*** DEADLOCK ***
[ 115.621174] 2 locks held by ip/1704:
[ 115.621174] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff815e6dbb>] rtnetlink_rcv+0x1b/0x40
[ 115.621174] #1: (&macvlan_netdev_addr_lock_key){+.....}, at: [<ffffffff815da5be>] dev_set_rx_mode+0x1e/0x40
[ 115.621174]
stack backtrace:
[ 115.621174] CPU: 3 PID: 1704 Comm: ip Not tainted 3.15.0-rc1+ #24
[ 115.621174] Hardware name: Hewlett-Packard HP xw8400 Workstation/0A08h, BIOS 786D5 v02.38 10/25/2010
[ 115.621174] ffffffff82339ae0 ffff880465f79568 ffffffff816ee20c ffffffff82339ae0
[ 115.621174] ffff880465f795a8 ffffffff816e9e1b ffff880465f79600 ffff880465b019c8
[ 115.621174] 0000000000000001 0000000000000002 ffff880465b019c8 ffff880465b01230
[ 115.621174] Call Trace:
[ 115.621174] [<ffffffff816ee20c>] dump_stack+0x4d/0x66
[ 115.621174] [<ffffffff816e9e1b>] print_circular_bug+0x200/0x20e
[ 115.621174] [<ffffffff810d4d43>] __lock_acquire+0x1773/0x1a60
[ 115.621174] [<ffffffff810d3172>] ? trace_hardirqs_on_caller+0xb2/0x1d0
[ 115.621174] [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[ 115.621174] [<ffffffff815df49c>] ? dev_uc_sync+0x3c/0x80
[ 115.621174] [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[ 115.621174] [<ffffffff815df49c>] ? dev_uc_sync+0x3c/0x80
[ 115.621174] [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[ 115.621174] [<ffffffffa0696d2a>] macvlan_set_mac_lists+0xca/0x110 [macvlan]
[ 115.621174] [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[ 115.621174] [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[ 115.621174] [<ffffffff815da6be>] __dev_open+0xde/0x140
[ 115.621174] [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[ 115.621174] [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[ 115.621174] [<ffffffff811e1db1>] ? mem_cgroup_bad_page_check+0x21/0x30
[ 115.621174] [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[ 115.621174] [<ffffffff810d394c>] ? __lock_acquire+0x37c/0x1a60
[ 115.621174] [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[ 115.621174] [<ffffffff815ea169>] ? rtnl_newlink+0xe9/0x730
[ 115.621174] [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[ 115.621174] [<ffffffff810d329d>] ? trace_hardirqs_on+0xd/0x10
[ 115.621174] [<ffffffff815e6dbb>] ? rtnetlink_rcv+0x1b/0x40
[ 115.621174] [<ffffffff815e6de0>] ? rtnetlink_rcv+0x40/0x40
[ 115.621174] [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[ 115.621174] [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[ 115.621174] [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[ 115.621174] [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[ 115.621174] [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[ 115.621174] [<ffffffff8119d4af>] ? might_fault+0x5f/0xb0
[ 115.621174] [<ffffffff8119d4f8>] ? might_fault+0xa8/0xb0
[ 115.621174] [<ffffffff8119d4af>] ? might_fault+0x5f/0xb0
[ 115.621174] [<ffffffff815cb51e>] ? verify_iovec+0x5e/0xe0
[ 115.621174] [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[ 115.621174] [<ffffffff816faa0d>] ? __do_page_fault+0x11d/0x570
[ 115.621174] [<ffffffff810cfe9f>] ? up_read+0x1f/0x40
[ 115.621174] [<ffffffff816fab04>] ? __do_page_fault+0x214/0x570
[ 115.621174] [<ffffffff8120a10b>] ? mntput_no_expire+0x6b/0x1c0
[ 115.621174] [<ffffffff8120a0b7>] ? mntput_no_expire+0x17/0x1c0
[ 115.621174] [<ffffffff8120a284>] ? mntput+0x24/0x40
[ 115.621174] [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[ 115.621174] [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[ 115.621174] [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b
Fix this by correctly providing macvlan lockdep class.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d38569ab2bba6e6b3233acfc3a84cdbcfbd1f79f ]
This reverts commit dc8eaaa006350d24030502a4521542e74b5cb39f.
vlan: Fix lockdep warning when vlan dev handle notification
Instead we use the new new API to find the lock subclass of
our vlan device. This way we can support configurations where
vlans are interspersed with other devices:
bond -> vlan -> macvlan -> vlan
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 25175ba5c9bff9aaf0229df34bb5d54c81633ec3 ]
Currently netif_addr_lock_nested assumes that there can be only
a single nesting level between 2 devices. However, if we
have multiple devices of the same type stacked, this fails.
For example:
eth0 <-- vlan0.10 <-- vlan0.10.20
A more complicated configuration may stack more then one type of
device in different order.
Ex:
eth0 <-- vlan0.10 <-- macvlan0 <-- vlan1.10.20 <-- macvlan1
This patch adds an ndo_* function that allows each stackable
device to report its nesting level. If the device doesn't
provide this function default subclass of 1 is used.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4085ebe8c31face855fd01ee40372cb4aab1df3a ]
Multiple devices in the kernel can be stacked/nested and they
need to know their nesting level for the purposes of lockdep.
This patch provides a generic function that determines a nesting
level of a particular device by its type (ex: vlan, macvlan, etc).
We only care about nesting of the same type of devices.
For example:
eth0 <- vlan0.10 <- macvlan0 <- vlan1.20
The nesting level of vlan1.20 would be 1, since there is another vlan
in the stack under it.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many people reported preemption/reschedule problems with i386 kernels
for .13 and .14. After Michele bisected this to a combination of
3e8e42c69bb ("sched: Revert need_resched() to look at TIF_NEED_RESCHED")
ded79754754 ("irq: Force hardirq exit's softirq processing on its own stack")
it finally dawned on me that i386's current_thread_info() was to
blame.
When we are on interrupt/exception stacks, we fail to observe the
right TIF_NEED_RESCHED bit and therefore the PREEMPT_NEED_RESCHED
folding malfunctions.
Current upstream fixes this by making i386 behave the same as x86_64
already did:
2432e1364bbe ("x86: Nuke the supervisor_stack field in i386 thread_info")
b807902a88c4 ("x86: Nuke GET_THREAD_INFO_WITH_ESP() macro for i386")
0788aa6a23cb ("x86: Prepare removal of previous_esp from i386 thread_info structure")
198d208df437 ("x86: Keep thread_info on thread stack in x86_32")
However, that is far too much to stuff into -stable. Therefore I
propose we merge the below patch which uses task_thread_info(current)
for tif_need_resched() instead of the ESP based current_thread_info().
This makes sure we always observe the one true TIF_NEED_RESCHED bit
and things will work as expected again.
Cc: bp@alien8.de
Cc: fweisbec@gmail.com
Cc: david.a.cohen@linux.intel.com
Cc: mingo@kernel.org
Cc: fweisbec@gmail.com
Cc: greg@kroah.com
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: gregkh@linuxfoundation.org
Cc: pbonzini@redhat.com
Cc: rostedt@goodmis.org
Cc: stefan.bader@canonical.com
Cc: mingo@kernel.org
Cc: toralf.foerster@gmx.de
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: torvalds@linux-foundation.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: <stable-commits@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: peterz@infradead.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: barra_cuda@katamail.com
Tested-by: Stefan Bader <stefan.bader@canonical.com>
Tested-by: Toralf F¿rster <toralf.foerster@gmx.de>
Tested-by: Michele Ballabio <barra_cuda@katamail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140409142447.GD13658@twins.programming.kicks-ass.net
|
|
commit ad36d28293936b03d6b7996e9d6aadfd73c0eb08 upstream.
Added the functions task_ppid_nr_ns() and task_ppid_nr() to abstract the lookup
of the PPID (real_parent's pid_t) of a process, including rcu locking, in the
arbitrary and init_pid_ns.
This provides an alternative to sys_getppid(), which is relative to the child
process' pid namespace.
(informed by ebiederman's 6c621b7e)
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a4aeec8d2d6a3edeffbdfae451cdf05cbf0fefd upstream.
The AHCI spec allows implementations to issue commands in tag order
rather than FIFO order:
5.3.2.12 P:SelectCmd
HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1)
or HBA selects the command to issue that has had the
PxCI bit set to '1' longer than any other command
pending to be issued.
The result is that commands posted sequentially (time-wise) may play out
of sequence when issued by hardware.
This behavior has likely been hidden by drives that arrange for commands
to complete in issue order. However, it appears recent drives (two from
different vendors that we have found so far) inflict out-of-order
completions as a matter of course. So, we need to take care to maintain
ordered submission, otherwise we risk triggering a drive to fall out of
sequential-io automation and back to random-io processing, which incurs
large latency and degrades throughput.
This issue was found in simple benchmarks where QD=2 seq-write
performance was 30-50% *greater* than QD=32 seq-write performance.
Tagging for -stable and making the change globally since it has a low
risk-to-reward ratio. Also, word is that recent versions of an unnamed
OS also does it this way now. So, drives in the field are already
experienced with this tag ordering scheme.
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ed Ciechanowski <ed.ciechanowski@intel.com>
Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7aa84d9cb9f26da1a9312c3e39dbd1a3c25a426 upstream.
Commit 4550dd6c6b062 introduced for_each_bvec() which iterates over each
bvec attached to a bio or bip. However, the macro fails to check bi_size
before dereferencing which can lead to crashes while counting/mapping
integrity scatterlist segments.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2ebb3a921c1ca1e2ddd9242e95a1989a50c4c68 upstream.
The current mainline has copies propagated to *all* nodes, then
tears down the copies we made for nodes that do not contain
counterparts of the desired mountpoint. That sets the right
propagation graph for the copies (at teardown time we move
the slaves of removed node to a surviving peer or directly
to master), but we end up paying a fairly steep price in
useless allocations. It's fairly easy to create a situation
where N calls of mount(2) create exactly N bindings, with
O(N^2) vfsmounts allocated and freed in process.
Fortunately, it is possible to avoid those allocations/freeings.
The trick is to create copies in the right order and find which
one would've eventually become a master with the current algorithm.
It turns out to be possible in O(nodes getting propagation) time
and with no extra allocations at all.
One part is that we need to make sure that eventual master will be
created before its slaves, so we need to walk the propagation
tree in a different order - by peer groups. And iterate through
the peers before dealing with the next group.
Another thing is finding the (earlier) copy that will be a master
of one we are about to create; to do that we are (temporary) marking
the masters of mountpoints we are attaching the copies to.
Either we are in a peer of the last mountpoint we'd dealt with,
or we have the following situation: we are attaching to mountpoint M,
the last copy S_0 had been attached to M_0 and there are sequences
S_0...S_n, M_0...M_n such that S_{i+1} is a master of S_{i},
S_{i} mounted on M{i} and we need to create a slave of the first S_{k}
such that M is getting propagation from M_{k}. It means that the master
of M_{k} will be among the sequence of masters of M. On the
other hand, the nearest marked node in that sequence will either
be the master of M_{k} or the master of M_{k-1} (the latter -
in the case if M_{k-1} is a slave of something M gets propagation
from, but in a wrong peer group).
So we go through the sequence of masters of M until we find
a marked one (P). Let N be the one before it. Then we go through
the sequence of masters of S_0 until we find one (say, S) mounted
on a node D that has P as master and check if D is a peer of N.
If it is, S will be the master of new copy, if not - the master of S
will be.
That's it for the hard part; the rest is fairly simple. Iterator
is in next_group(), handling of one prospective mountpoint is
propagate_one().
It seems to survive all tests and gives a noticably better performance
than the current mainline for setups that are seriously using shared
subtrees.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03367ef5ea811475187a0732aada068919e14d61 upstream.
Only ws2012r2 hosts support the ability to reconnect to the host on VMBUS. This functionality
is needed by kexec in Linux. To use this functionality we need to negotiate version 3.0 of the
VMBUS protocol.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3064639423c48d6e0eb9ecc27c512a58e38c6c57 upstream.
There could be a case, when NFSd file system is mounted in network, different
to socket's one, like below:
"ip netns exec" creates new network and mount namespace, which duplicates NFSd
mount point, created in init_net context. And thus NFS server stop in nested
network context leads to RPCBIND client destruction in init_net.
Then, on NFSd start in nested network context, rpc.nfsd process creates socket
in nested net and passes it into "write_ports", which leads to RPCBIND sockets
creation in init_net context because of the same reason (NFSd monut point was
created in init_net context). An attempt to register passed socket in nested
net leads to panic, because no RPCBIND client present in nexted network
namespace.
This patch add check that passed socket's net matches NFSd superblock's one.
And returns -EINVAL error to user psace otherwise.
v2: Put socket on exit.
Reported-by: Weng Meiling <wengmeiling.weng@huawei.com>
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5acda9d12dcf1ad0d9a5a2a7c646de3472fa7555 upstream.
After commit 839a8e8660b6 ("writeback: replace custom worker pool
implementation with unbound workqueue") when device is removed while we
are writing to it we crash in bdi_writeback_workfn() ->
set_worker_desc() because bdi->dev is NULL.
This can happen because even though bdi_unregister() cancels all pending
flushing work, nothing really prevents new ones from being queued from
balance_dirty_pages() or other places.
Fix the problem by clearing BDI_registered bit in bdi_unregister() and
checking it before scheduling of any flushing work.
Fixes: 839a8e8660b6777e7fe4e80af1a048aebe2b5977
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Derek Basehore <dbasehore@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a9c3f68f3cd8d55f809fbdb0c138ed061ea1bd25 upstream.
The user-settable knob, low_latency, has been the source of
several BUG reports which stem from flush_to_ldisc() running
in interrupt context. Since 3.12, which added several sleeping
locks (termios_rwsem and buf->lock) to the input processing path,
the frequency of these BUG reports has increased.
Note that changes in 3.12 did not introduce this regression;
sleeping locks were first added to the input processing path
with the removal of the BKL from N_TTY in commit
a88a69c91256418c5907c2f1f8a0ec0a36f9e6cc,
'n_tty: Fix loss of echoed characters and remove bkl from n_tty'
and later in commit 38db89799bdf11625a831c5af33938dcb11908b6,
'tty: throttling race fix'. Since those changes, executing
flush_to_ldisc() in interrupt_context (ie, low_latency set), is unsafe.
However, since most devices do not validate if the low_latency
setting is appropriate for the context (process or interrupt) in
which they receive data, some reports are due to misconfiguration.
Further, serial dma devices for which dma fails, resort to
interrupt receiving as a backup without resetting low_latency.
Historically, low_latency was used to force wake-up the reading
process rather than wait for the next scheduler tick. The
effect was to trim multiple milliseconds of latency from
when the process would receive new data.
Recent tests [1] have shown that the reading process now receives
data with only 10's of microseconds latency without low_latency set.
Remove the low_latency rx steering from tty_flip_buffer_push();
however, leave the knob as an optional hint to drivers that can
tune their rx fifos and such like. Cleanup stale code comments
regarding low_latency.
[1] https://lkml.org/lkml/2014/2/20/434
"Yay.. thats an annoying historical pain in the butt gone."
-- Alan Cox
Reported-by: Beat Bolli <bbolli@ewanet.ch>
Reported-by: Pavel Roskin <proski@gnu.org>
Acked-by: David Sterba <dsterba@suse.cz>
Cc: Grant Edwards <grant.b.edwards@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Hal Murray <murray+fedora@ip-64-139-1-69.sjc.megapath.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03b8c7b623c80af264c4c8d6111e5c6289933666 upstream.
If an architecture has futex_atomic_cmpxchg_inatomic() implemented and there
is no runtime check necessary, allow to skip the test within futex_init().
This allows to get rid of some code which would always give the same result,
and also allows the compiler to optimize a couple of if statements away.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Link: http://lkml.kernel.org/r/20140302120947.GA3641@osiris
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use cmpxchg() to atomically set i_flags instead of clearing out the
S_IMMUTABLE, S_APPEND, etc. flags and then setting them from the
EXT4_IMMUTABLE_FL, EXT4_APPEND_FL flags, since this opens up a race
where an immutable file has the immutable flag cleared for a brief
window of time.
Reported-by: John Sullivan <jsrhbz@kanargh.force9.co.uk>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some drivers incorrectly assign vlan acceleration features to
vlan_features thus causing issues for Q-in-Q vlan configurations.
Warn the user of such cases.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb. However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers. That may not
always be the case. If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.
A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated. This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_zerocopy can copy elements of the frags array between skbs, but it doesn't
orphan them. Also, it doesn't handle errors, so this patch takes care of that
as well, and modify the callers accordingly. skb_tx_error() is also added to
the callers so they will signal the failed delivery towards the creator of the
skb.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a race which happens by freeing an object on the stack.
Quoting Julius:
> The issue is
> that it calls usbnet_terminate_urbs() before that, which temporarily
> installs a waitqueue in dev->wait in order to be able to wait on the
> tasklet to run and finish up some queues. The waiting itself looks
> okay, but the access to 'dev->wait' is totally unprotected and can
> race arbitrarily. I think in this case usbnet_bh() managed to succeed
> it's dev->wait check just before usbnet_terminate_urbs() sets it back
> to NULL. The latter then finishes and the waitqueue_t structure on its
> stack gets overwritten by other functions halfway through the
> wake_up() call in usbnet_bh().
The fix is to just not allocate the data structure on the stack.
As dev->wait is abused as a flag it also takes a runtime PM change
to fix this bug.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Grant Grundler <grundler@google.com>
Tested-by: Grant Grundler <grundler@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) OpenVswitch's lookup_datapath() returns error pointers, so don't
check against NULL. From Jiri Pirko.
2) pfkey_compile_policy() code path tries to do a GFP_KERNEL allocation
under RCU locks, fix by using GFP_ATOMIC when necessary. From
Nikolay Aleksandrov.
3) phy_suspend() indirectly passes uninitialized data into the ethtool
get wake-on-land implementations. Fix from Sebastian Hesselbarth.
4) CPSW driver unregisters CPTS twice, fix from Benedikt Spranger.
5) If SKB allocation of reply packet fails, vxlan's arp_reduce() defers
a NULL pointer. Fix from David Stevens.
6) IPV6 neigh handling in vxlan doesn't validate the destination
address properly, and it builds a packet with the src and dst
reversed. Fix also from David Stevens.
7) Fix spinlock recursion during subscription failures in TIPC stack,
from Erik Hugne.
8) Revert buggy conversion of davinci_emac to devm_request_irq, from
Chrstian Riesch.
9) Wrong flags passed into forwarding database netlink notifications,
from Nicolas Dichtel.
10) The netpoll neighbour soliciation handler checks wrong ethertype,
needs to be ETH_P_IPV6 rather than ETH_P_ARP. Fix from Li RongQing.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
tipc: fix spinlock recursion bug for failed subscriptions
vxlan: fix nonfunctional neigh_reduce()
net: davinci_emac: Fix rollback of emac_dev_open()
net: davinci_emac: Replace devm_request_irq with request_irq
netpoll: fix the skb check in pkt_is_ns
net: micrel : ks8851-ml: add vdd-supply support
ip6mr: fix mfc notification flags
ipmr: fix mfc notification flags
rtnetlink: fix fdb notification flags
tcp: syncookies: do not use getnstimeofday()
netlink: fix setsockopt in mmap examples in documentation
openvswitch: Correctly report flow used times for first 5 minutes after boot.
via-rhine: Disable device in error path
ATHEROS-ATL1E: Convert iounmap to pci_iounmap
vxlan: fix potential NULL dereference in arp_reduce()
cnic: Update version to 2.5.20 and copyright year.
cnic,bnx2i,bnx2fc: Fix inconsistent use of page size
cnic: Use proper ulp_ops for per device operations.
net: cdc_ncm: fix control message ordering
ipv6: ip6_append_data_mtu do not handle the mtu of the second fragment properly
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull trace fix from Steven Rostedt:
"Vaibhav Nagarnaik discovered that since 3.10 a clean-up patch made the
array index in the trace event format bogus.
He supplied an elegant solution that uses __stringify() and also
removes the need for the event_storage and event_storage_mutex and
also cuts off a few K of overhead from the trace events"
* tag 'trace-fixes-v3.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix array size mismatch in format string
|
|
Add remove_linear_migration_ptes_from_nonlinear(), to fix an interesting
little include/linux/swapops.h:131 BUG_ON(!PageLocked) found by trinity:
indicating that remove_migration_ptes() failed to find one of the
migration entries that was temporarily inserted.
The problem comes from remap_file_pages()'s switch from vma_interval_tree
(good for inserting the migration entry) to i_mmap_nonlinear list (no good
for locating it again); but can only be a problem if the remap_file_pages()
range does not cover the whole of the vma (zap_pte() clears the range).
remove_migration_ptes() needs a file_nonlinear method to go down the
i_mmap_nonlinear list, applying linear location to look for migration
entries in those vmas too, just in case there was this race.
The file_nonlinear method does need rmap_walk_control.arg to do this;
but it never needed vma passed in - vma comes from its own iteration.
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Reported-and-tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In event format strings, the array size is reported in two locations.
One in array subscript and then via the "size:" attribute. The values
reported there have a mismatch.
For e.g., in sched:sched_switch the prev_comm and next_comm character
arrays have subscript values as [32] where as the actual field size is
16.
name: sched_switch
ID: 301
format:
field:unsigned short common_type; offset:0; size:2; signed:0;
field:unsigned char common_flags; offset:2; size:1; signed:0;
field:unsigned char common_preempt_count; offset:3; size:1;signed:0;
field:int common_pid; offset:4; size:4; signed:1;
field:char prev_comm[32]; offset:8; size:16; signed:1;
field:pid_t prev_pid; offset:24; size:4; signed:1;
field:int prev_prio; offset:28; size:4; signed:1;
field:long prev_state; offset:32; size:8; signed:1;
field:char next_comm[32]; offset:40; size:16; signed:1;
field:pid_t next_pid; offset:56; size:4; signed:1;
field:int next_prio; offset:60; size:4; signed:1;
After bisection, the following commit was blamed:
92edca0 tracing: Use direct field, type and system names
This commit removes the duplication of strings for field->name and
field->type assuming that all the strings passed in
__trace_define_field() are immutable. This is not true for arrays, where
the type string is created in event_storage variable and field->type for
all array fields points to event_storage.
Use __stringify() to create a string constant for the type string.
Also, get rid of event_storage and event_storage_mutex that are not
needed anymore.
also, an added benefit is that this reduces the overhead of events a bit more:
text data bss dec hex filename
8424787 2036472 1302528 11763787 b3804b vmlinux
8420814 2036408 1302528 11759750 b37086 vmlinux.patched
Link: http://lkml.kernel.org/r/1392349908-29685-1-git-send-email-vnagarnaik@google.com
Cc: Laurent Chavey <chavey@google.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Vaibhav Nagarnaik <vnagarnaik@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
This is a context modified revert of commit 6a9612e2cb22
("net: cdc_ncm: remove ncm_parm field") which introduced
a NCM specification violation, causing setup errors for
some devices. These errors resulted in the device and
host disagreeing about shared settings, with complete
failure to communicate as the end result.
The NCM specification require that many of the NCM specific
control reuests are sent only while the NCM Data Interface
is in alternate setting 0. Reverting the commit ensures that
we follow this requirement.
Fixes: 6a9612e2cb22 ("net: cdc_ncm: remove ncm_parm field")
Reported-and-tested-by: Pasi Kärkkäinen <pasik@iki.fi>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
1) Fix a sleep in atomic when pfkey_sadb2xfrm_user_sec_ctx()
is called from pfkey_compile_policy().
Fix from Nikolay Aleksandrov.
2) security_xfrm_policy_alloc() can be called in process and atomic
context. Add an argument to let the callers choose the appropriate
way. Fix from Nikolay Aleksandrov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull audit namespace fixes from Eric Biederman:
"Starting with 3.14-rc1 the audit code is faulty (think oopses and
races) with respect to how it computes the network namespace of which
socket to reply to, and I happened to notice by chance when reading
through the code.
My testing and the automated build bots don't find any problems with
these fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
audit: Update kdoc for audit_send_reply and audit_list_rules_send
audit: Send replies in the proper network namespace.
audit: Use struct net not pid_t to remember the network namespce to reply in
|
|
Merge misc fixes from Andrew Morton:
"Nine fixes"
* emailed patches from Andrew Morton akpm@linux-foundation.org>:
cris: convert ffs from an object-like macro to a function-like macro
hfsplus: add HFSX subfolder count support
tools/testing/selftests/ipc/msgque.c: handle msgget failure return correctly
MAINTAINERS: blackfin: add git repository
revert "kallsyms: fix absolute addresses for kASLR"
mm/Kconfig: fix URL for zsmalloc benchmark
fs/proc/base.c: fix GPF in /proc/$PID/map_files
mm/compaction: break out of loop on !PageBuddy in isolate_freepages_block
mm: fix GFP_THISNODE callers and clarify
|
|
GFP_THISNODE is for callers that implement their own clever fallback to
remote nodes. It restricts the allocation to the specified node and
does not invoke reclaim, assuming that the caller will take care of it
when the fallback fails, e.g. through a subsequent allocation request
without GFP_THISNODE set.
However, many current GFP_THISNODE users only want the node exclusive
aspect of the flag, without actually implementing their own fallback or
triggering reclaim if necessary. This results in things like page
migration failing prematurely even when there is easily reclaimable
memory available, unless kswapd happens to be running already or a
concurrent allocation attempt triggers the necessary reclaim.
Convert all callsites that don't implement their own fallback strategy
to __GFP_THISNODE. This restricts the allocation a single node too, but
at the same time allows the allocator to enter the slowpath, wake
kswapd, and invoke direct reclaim if necessary, to make the allocation
happen when memory is full.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Jan Stancek <jstancek@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro.
Clean up file table accesses (get rid of fget_light() in favor of the
fdget() interface), add proper file position locking.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
get rid of fget_light()
sockfd_lookup_light(): switch to fdget^W^Waway from fget_light
vfs: atomic f_pos accesses as per POSIX
ocfs2 syncs the wrong range...
|
