| Age | Commit message (Collapse) | Author |
|---|
|
commit 95cadace8f3959282e76ebf8b382bd0930807d2c upstream.
This patch allows FILEIO to update hw_max_sectors based on the current
max_bytes_per_io. This is required because vfs_[writev,readv]() can accept
a maximum of 2048 iovecs per call, so the enforced hw_max_sectors really
needs to be calculated based on block_size.
This addresses a >= v3.5 bug where block_size=512 was rejecting > 1M
sized I/O requests, because FD_MAX_SECTORS was hardcoded to 2048 for
the block_size=4096 case.
(v2: Use max_bytes_per_io instead of ->update_hw_max_sectors)
Reported-by: Henrik Goldman <hg@x-formation.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 561bf15892375597ee59d473a704a3e634c4f311 upstream
This patch moves ISCSI_OP_REJECT failures into iscsit_sequence_cmd()
in order to avoid external iscsit_reject_cmd() reject usage for all
PDU types.
It also updates PDU specific handlers for traditional iscsi-target
code to not reset the session after posting a ISCSI_OP_REJECT during
setup.
(v2: Fix CMDSN_LOWER_THAN_EXP for ISCSI_OP_SCSI to call
target_put_sess_cmd() after iscsit_sequence_cmd() failure)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba159914086f06532079fc15141f46ffe7e04a41 upstream
This patch changes iscsit_add_reject() + iscsit_add_reject_from_cmd()
usage to not sleep on iscsi_cmd->reject_comp to address a free-after-use
usage bug in v3.10 with iser-target code.
It saves ->reject_reason for use within iscsit_build_reject() so the
correct value for both transport cases. It also drops the legacy
fail_conn parameter usage throughput iscsi-target code and adds
two iscsit_add_reject_cmd() and iscsit_reject_cmd helper functions,
along with various small cleanups.
(v2: Re-enable target_put_sess_cmd() to be called from
iscsit_add_reject_from_cmd() for rejects invoked after
target_get_sess_cmd() has been called)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b2cb96494d83b894a43ba8b9023eead8ff50684b upstream.
This patch addresses a bug where RDMA_CM_EVENT_DISCONNECTED may occur
before the connection shutdown has been completed by rx/tx threads,
that causes isert_free_conn() to wait indefinately on ->conn_wait.
This patch allows isert_disconnect_work code to invoke rdma_disconnect
when isert_disconnect_work() process context is started by client
session reset before isert_free_conn() code has been reached.
It also adds isert_conn->conn_mutex protection for ->state within
isert_disconnect_work(), isert_cq_comp_err() and isert_free_conn()
code, along with isert_check_state() for wait_event usage.
(v2: Add explicit iscsit_cause_connection_reinstatement call
during isert_disconnect_work() to force conn reset)
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Go ahead and propigate up the ->cmd_kref put return value from
target_put_sess_cmd() -> transport_release_cmd() -> transport_put_cmd()
-> transport_generic_free_cmd().
This is useful for certain fabrics when determining the active I/O
shutdown case with SCF_ACK_KREF where a final target_put_sess_cmd()
is still required by the caller.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Switch back to pre commit 1c7b13fe652 list splicing logic for active I/O
shutdown with tcm_qla2xxx + ib_srpt fabrics.
The original commit was done under the incorrect assumption that it's safe to
walk se_sess->sess_cmd_list unprotected in target_wait_for_sess_cmds() after
sess->sess_tearing_down = 1 has been set by target_sess_cmd_list_set_waiting()
during session shutdown.
So instead of adding sess->sess_cmd_lock protection around sess->sess_cmd_list
during target_wait_for_sess_cmds(), switch back to sess->sess_wait_list to
allow wait_for_completion() + TFO->release_cmd() to occur without having to
walk ->sess_cmd_list after the list_splice.
Also add a check to exit if target_sess_cmd_list_set_waiting() has already
been called, and add a WARN_ON to check for any fabric bug where new se_cmds
are added to sess->sess_cmd_list after sess->sess_tearing_down = 1 has already
been set.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Drop unused transport_wait_for_tasks() check in target_wait_for_sess_cmds
shutdown code, and convert tcm_qla2xxx + ib_srpt fabric drivers.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Some were incremented, but never used anywhere from what I could tell.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Add basic struct iscsit_transport API template to allow iscsi-target for
running with external transport modules using existing iscsi_target_core.h
code.
For all external modules, this calls try_module_get() and module_put()
to obtain + release an external iscsit_transport module reference count.
Also include the iscsi-target symbols necessary in iscsi_transport.h to
allow external transport modules to function.
v3 changes:
- Add iscsit_build_reject export for ISTATE_SEND_REJECT usage
v2 changes:
- Drop unnecessary export of iscsit_get_transport + iscsit_put_transport (roland)
- Add ->iscsit_queue_data_in() to remove extra context switch on RDMA_WRITE
- Add ->iscsit_queue_status() to remove extra context switch on IB_SEND status
- Add ->iscsit_get_dataout() to remove extra context switch on RDMA_READ
- Drop ->iscsit_free_cmd()
- Drop ->iscsit_unmap_cmd()
- Rename iscsit_create_transport() -> iscsit_register_transport() (andy)
- Rename iscsit_destroy_transport() -> iscsit_unregister_transport() (andy)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Export target_get_sess_cmd() symbol so that it can be used by
iscsi-target.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
iblock_execute_unmap() and fd_execute_unmap share a lot of code.
Add sbc_execute_unmap() helper to remove duplicated code for
iblock_execute_unmap() and fd_execute_unmap().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Trivial, but WRITE SAME is an SBC command so it seems strange for a
related function (defined in target_core_sbc.c) to be in the spc_
namespace.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
SBC-3 (revision 35) says:
The PARAMETER LIST LENGTH field specifies the length in bytes of the
UNMAP parameter list that is available to be transferred from the
Data-Out Buffer. If the parameter list length is greater than zero
and less than 0008h (i.e., eight), then the device server shall
terminate the command with CHECK CONDITION status with the sense key
set to ILLEGAL REQUEST and the additional sense code set to
PARAMETER LIST LENGTH ERROR. A PARAMETER LIST LENGTH set to zero
specifies that no data shall be sent.
so our sense code for too-short descriptors was wrong, and we were
incorrectly failing commands that didn't transfer any descriptors.
While we're at it, also handle the UNMAP check:
If the ANCHOR bit is set to one, and the ANC_SUP bit in the Logical
Block Provisioning VPD page (see 6.6.4) is set to zero, then the
device server shall terminate the command with CHECK CONDITION
status with the sense key set to ILLEGAL REQUEST and the additional
sense code set to INVALID FIELD IN CDB.
(chris boot: Fix wrong cut+paste comment in transport_send_check_condition_and_sense)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch changes LIO to use the configfs backend device name as the
model if you echo '1' to an individual device's emulate_model_alias attribute.
This is a valid operation only on devices with an export count of 0.
Signed-off-by: Tregaron Bayly <tbayly@bluehost.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch allows IBLOCK to check block hints in request_queue->flush_flags
when reporting current backend device WriteCacheEnabled status to a remote
SCSI initiator port.
This is done via a se_subsystem_api->get_write_cache() call instead of a
backend se_device creation time flag, as we expect REQ_FLUSH bits to possibly
change from an underlying blk_queue_flush() by the SCSI disk driver, or
internal raw struct block_device driver usage.
Also go ahead and update iblock_execute_rw() bio I/O path code to use
REQ_FLUSH + REQ_FUA hints when determining WRITE_FUA usage, and make SPC
emulation code use a spc_check_dev_wce() helper to handle both types of
cases for virtual backend subsystem drivers.
(asias: Drop unnecessary comparsion operators)
Reported-by: majianpeng <majianpeng@gmail.com>
Cc: majianpeng <majianpeng@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
"buf" is 128 characters and "vpd->device_identifier" is 256. It makes
the static checkers complain.
Also bump VPD_TMP_BUF_SIZE to match INQUIRY_VPD_DEVICE_IDENTIFIER_LEN.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Some target drivers might need to access the inquiry data
directly, without sending out the actual command.
So export these functions.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Introduce TCM_NO_SENSE, mapping to sense code
'Not ready, no additional sense information'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Thanks for reviews, looking a lot better.
---- 8< ----
Initiator access config could be easier. The way other storage vendors
have addressed this is to support initiator groups: the admin adds
initiator WWNs to the group, and then LUN permissions can be granted for
the entire group at once.
Instead of changing ktarget's configfs interface, this patch keeps
the configfs interface per-initiator-wwn and just adds a 'tag' field
for each. This should be enough for user tools like targetcli to group
initiator ACLs and sync their configurations.
acl_tag is not used internally, but needs to be kept in configfs so that
all user tools can avoid dependencies on each other.
Code tested to work, although userspace pieces still to be implemented.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds [dev,lun]_link_magic value assignment + checks within generic
target_fabric_port_link() and target_fabric_mappedlun_link() code to ensure
destination config_item *target_item sent from configfs_symlink() ->
config_item_operations->allow_link() is the underlying se_device->dev_group
and se_lun->lun_group that we expect to symlink.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We already expect TFO->get_blocks() to return sector_t for zero value case
when doing WRITE_SAME to the end of the backend device, so go ahead and return
sector_t from spc_get_write_same_sectors() to handle this case properly.
Also, update the single iblock_execute_write_same() caller of this code.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a new max_write_same_len device attribute for use with
WRITE_SAME w/ UNMAP=0 backend emulation. This can be useful for
lowering the default backend value (IBLOCK uses 0xFFFF).
Also, update block limits VPD emulation code in spc_emulate_evpd_b0() to
report MAXIMUM WRITE SAME LENGTH, and enforce max_write_same_len during
sbc_parse() -> sbc_setup_write_same() CDB sanity checking for all emulated
WRITE_SAME w/ UNMAP=0 cases.
(Robert: Move max_write_same_len check in sbc_setup_write_same() to
check both WRITE_SAME w/ UNMAP=1 and w/ UNMAP=0 cases)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Robert Elliott <Elliott@hp.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a new sbc_ops->execute_write_same_unmap() caller for use
with WRITE_SAME w/ UNMAP=1, and performs the ->execute_cmd() setup based
this bit within sbc_setup_write_same() code.
Also, makes the changes in sbc_parse_cdb() to handle a sense_reason_t
return from sbc_setup_write_same() on error.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Pass the sense reason as an explicit return value from the I/O submission
path instead of storing it in struct se_cmd and using negative return
values. This cleans up a lot of the code pathes, and with the sparse
annotations for the new sense_reason_t type allows for much better
error checking.
(nab: Convert spc_emulate_modesense + spc_emulate_modeselect to use
sense_reason_t with Roland's MODE SELECT changes)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that the reservations and ALUA code have been cleaned up there is no need
for the get_device_rev method, as we only need the standards revision in the
inquiry data, where we can hardcode it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We always support ALUA for virtual backends, and never for physical ones. Simplify
the code to just deal with these two cases and remove the superflous abstractions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We do not support host-level reservations for the pscsi backend, and all
virtual backends are newere than SCSI-2, so just make the combined
SPC-3 + SCSI-2 support the only supported variant and kill the switches
for the different implementations, given that this code handles the no-op
version just fine.
(hch: Update DRF_SPC2_RESERVATIONS lock usage)
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We can just key off ordered tag emulation of the transport_type field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
No need to indirect through spc_parse_cdb if we only ever call it for
REPORT LUNS emulation.
(nab: Add missing EXPORT_SYMBOL for spc_emulate_report_luns)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
These really are sbc_ops, so name them correctly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Simplify the code a lot by killing the superflous struct se_subsystem_dev.
Instead se_device is allocated early on by the backend driver, which allocates
it as part of its own per-device structure, borrowing the scheme that is for
example used for inode allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a new target_submit_cmd_map_sgls() to pass pre-allocated
SGL memory using transport_generic_map_mem_to_cmd() logic into the generic
target submit I/O codepath.
It also adds a target_submit_cmd() wrapper around target_submit_cmd_map_sgls()
for existing fabric code that already assumes internal target-core SGL memory
allocation.
(v2: Rename to target_submit_cmd_map_sgls + drop TARGET_SCF_MAP_MEM flag
in favor of non zero sgl_count check)
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch drops se_subsystem_api->[write_cache,fua_write]_emulated flags
set by viritual FILEIO/IBLOCK/RD_MCP backend drivers in favor of explict
TRANSPORT_PLUGIN_PHBA_PDEV checks to know when to fail if userspace is
attempting to set virtual emulation bits for an pSCSI (passthrough)
backend device.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Every fabric driver has to supply a se_tfo->set_fabric_sense_len()
method, just so iSCSI can return an offset of 2. However, every fabric
driver is already allocating a sense buffer and passing it into the
target core, either via transport_init_se_cmd() or target_submit_cmd().
So instead of having iSCSI pass the start of its sense buffer into the
core and then later tell the core to skip the first 2 bytes, it seems
easier for iSCSI just to do the offset of 2 when it passes the sense
buffer into the core. Then we can drop the se_tfo->set_fabric_sense_len()
everywhere, and just add a couple of lines of code to iSCSI to set the
sense data length to the beginning of the buffer right before it sends
it over the network.
(nab: Remove .set_fabric_sense_len usage from tcm_qla2xxx_npiv_ops +
change transport_get_sense_buffer to follow v3.6-rc6 code w/o
->set_fabric_sense_len usage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
There are no callers of se_tfo->get_fabric_sense_len(), so we should
stop having every fabric driver implement it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Similar to INQUIRY and MODE SENSE, construct the sense data in a
buffer and later copy it to the scatterlist. Do not do anything,
but still clear a pending unit attention condition, if the allocation
length is zero.
However, SPC tells us that "If a REQUEST SENSE command is terminated with
CHECK CONDITION status [and] the REQUEST SENSE command was received on
an I_T nexus with a pending unit attention condition (i.e., before the
device server reports CHECK CONDITION status), then the device server
shall not clear the pending unit attention condition." Do the
transport_kmap_data_sg early to detect this case.
It also tells us "Device servers shall not adjust the additional sense
length to reflect truncation if the allocation length is less than the
sense data available", so do not do that! Note that the err variable
is write-only.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The pointer to the sense buffer is fetched by transport_get_sense_data,
but this is called by target_complete_ok_work long after pscsi_req_done
has freed the struct that contains it.
Pass instead the fabric's sense buffer to transport_complete,
and copy the data to it directly in transport_complete. Setting
SCF_TRANSPORT_TASK_SENSE also becomes a duty of transport_complete.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This was originally for helping fabrics to determine overflow/underflow
status, and has been superceeded by SCF_OVERFLOW_BIT + SCF_UNDERFLOW_BIT.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We want it to be possible for target_submit_cmd() to return errors up
to its fabric module callers. For now just update the prototype to
return an int, and update all callers to handle non-zero return values
as an error.
This is immediately useful for tcm_qla2xxx to fix a long-standing active
I/O session shutdown race, but tcm_fc, usb-gadget, and sbp-target the
fabric maintainers need to check + ACK that handling a target_submit_cmd()
failure due to session shutdown does not introduce regressions
(nab: Respin against for-next after initial NACK + update docbook comment +
fix double se_cmd init in exception path for usb-gadget)
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Chris Boot <bootc@bootc.net>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Many SCSI commands are defined to return a CHECK CONDITION / ILLEGAL
REQUEST with ASC set to LOGICAL BLOCK ADDRESS OUT OF RANGE if the
initiator sends a command that accesses a too-big LBA. Add an enum
value and case entries so that target code can return this status.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Since we set se_session.sess_tearing_down and stop new commands from
being added to se_session.sess_cmd_list before we wait for commands to
finish when freeing a session, there's no need for a separate
sess_wait_list -- if we let new commands be added to sess_cmd_list
after setting sess_tearing_down, that would be a bug that breaks the
logic of waiting in-flight commands.
Also rename target_splice_sess_cmd_list() to
target_sess_cmd_list_set_waiting(), since we are no longer splicing
onto a separate list.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
There are no in-tree users of target_get_sess_cmd() outside of
target_core_transport.c. Any new code should use the higher-level
target_submit_cmd() interface. So let's un-export target_get_sess_cmd()
and make it static to the one file where it's actually used.
(nab: Fix up minor fuzz to for-next)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The last functionality of the target processing thread is offloading possibly
long running task management requests from the submitter context. To keep
TMR semantics the same we need a single threaded ordered queue, which can
be provided by a per-device workqueue with the right flags.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Remove this command submission path which is not used by any in-tree driver.
This also removes the now unused new_cmd_map fabtric method, which a few
drivers implemented despite never calling transport_generic_handle_cdb_map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Just call target_execute_cmd directly. Also, convert loopback, sbp,
usb-gadget to use the newly exported target_execute_cmd().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Having all the unmap payload parsing in the backed is a bit ugly, but until
more drivers support it and we can find a good interface for all of them
that seems the way to go.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
