| Age | Commit message (Collapse) | Author |
|---|
|
The Accurate ECN allows echoing back the sum of bytes for
each IP ECN field value in the received packets using
AccECN option. This change implements AccECN option tx & rx
side processing without option send control related features
that are added by a later change.
Based on specification:
https://tools.ietf.org/id/draft-ietf-tcpm-accurate-ecn-28.txt
(Some features of the spec will be added in the later changes
rather than in this one).
A full-length AccECN option is always attempted but if it does
not fit, the minimum length is selected based on the counters
that have changed since the last update. The AccECN option
(with 24-bit fields) often ends in odd sizes so the option
write code tries to take advantage of some nop used to pad
the other TCP options.
The delivered_ecn_bytes pairs with received_ecn_bytes similar
to how delivered_ce pairs with received_ce. In contrast to
ACE field, however, the option is not always available to update
delivered_ecn_bytes. For ACK w/o AccECN option, the delivered
bytes calculated based on the cumulative ACK+SACK information
are assigned to one of the counters using an estimation
heuristic to select the most likely ECN byte counter. Any
estimation error is corrected when the next AccECN option
arrives. It may occur that the heuristic gets too confused
when there are enough different byte counter deltas between
ACKs with the AccECN option in which case the heuristic just
gives up on updating the counters for a while.
tcp_ecn_option sysctl can be used to select option sending
mode for AccECN: TCP_ECN_OPTION_DISABLED, TCP_ECN_OPTION_MINIMUM,
and TCP_ECN_OPTION_FULL.
This patch increases the size of tcp_info struct, as there is
no existing holes for new u32 variables. Below are the pahole
outcomes before and after this patch:
[BEFORE THIS PATCH]
struct tcp_info {
[...]
__u32 tcpi_total_rto_time; /* 244 4 */
/* size: 248, cachelines: 4, members: 61 */
}
[AFTER THIS PATCH]
struct tcp_info {
[...]
__u32 tcpi_total_rto_time; /* 244 4 */
__u32 tcpi_received_ce; /* 248 4 */
__u32 tcpi_delivered_e1_bytes; /* 252 4 */
__u32 tcpi_delivered_e0_bytes; /* 256 4 */
__u32 tcpi_delivered_ce_bytes; /* 260 4 */
__u32 tcpi_received_e1_bytes; /* 264 4 */
__u32 tcpi_received_e0_bytes; /* 268 4 */
__u32 tcpi_received_ce_bytes; /* 272 4 */
/* size: 280, cachelines: 5, members: 68 */
}
This patch uses the existing 1-byte holes in the tcp_sock_write_txrx
group for new u8 members, but adds a 4-byte hole in tcp_sock_write_rx
group after the new u32 delivered_ecn_bytes[3] member. Therefore, the
group size of tcp_sock_write_rx is increased from 96 to 112. Below
are the pahole outcomes before and after this patch:
[BEFORE THIS PATCH]
struct tcp_sock {
[...]
u8 received_ce_pending:4; /* 2522: 0 1 */
u8 unused2:4; /* 2522: 4 1 */
/* XXX 1 byte hole, try to pack */
[...]
u32 rcv_rtt_last_tsecr; /* 2668 4 */
[...]
__cacheline_group_end__tcp_sock_write_rx[0]; /* 2728 0 */
[...]
/* size: 3200, cachelines: 50, members: 167 */
}
[AFTER THIS PATCH]
struct tcp_sock {
[...]
u8 received_ce_pending:4;/* 2522: 0 1 */
u8 unused2:4; /* 2522: 4 1 */
u8 accecn_minlen:2; /* 2523: 0 1 */
u8 est_ecnfield:2; /* 2523: 2 1 */
u8 unused3:4; /* 2523: 4 1 */
[...]
u32 rcv_rtt_last_tsecr; /* 2668 4 */
u32 delivered_ecn_bytes[3];/* 2672 12 */
/* XXX 4 bytes hole, try to pack */
[...]
__cacheline_group_end__tcp_sock_write_rx[0]; /* 2744 0 */
[...]
/* size: 3200, cachelines: 50, members: 171 */
}
Signed-off-by: Ilpo Järvinen <ij@kernel.org>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Co-developed-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Signed-off-by: Chia-Yu Chang <chia-yu.chang@nokia-bell-labs.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250916082434.100722-7-chia-yu.chang@nokia-bell-labs.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
AMD Seamless Firmware Servicing (SFS) is a secure method to allow
non-persistent updates to running firmware and settings without
requiring BIOS reflash and/or system reset.
SFS does not address anything that runs on the x86 processors and
it can be used to update ASP firmware, modules, register settings
and update firmware for other microprocessors like TMPM, etc.
SFS driver support adds ioctl support to communicate the SFS
commands to the ASP/PSP by using the TEE mailbox interface.
The Seamless Firmware Servicing (SFS) driver is added as a
PSP sub-device.
For detailed information, please look at the SFS specifications:
https://www.amd.com/content/dam/amd/en/documents/epyc-technical-docs/specifications/58604.pdf
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Link: https://lore.kernel.org/cover.1758057691.git.ashish.kalra@amd.com
|
|
The handling for variable-length ioctl commands in hidraw_ioctl() is
rather complex and the check for the data direction is incomplete.
Simplify this code by factoring out the various ioctls grouped by dir
and size, and using a switch() statement with the size masked out, to
ensure the rest of the command is correctly matched.
Fixes: 9188e79ec3fd ("HID: add phys and name ioctls to hidraw")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Returning buffers via a ring is performant and convenient, but it
becomes a problem when/if the user misconfigured the ring size and it
becomes full. Add a synchronous way to return buffers back to the page
pool via a new register opcode. It's supposed to be a reliable slow
path for refilling.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
During the connection establishment, a peer can tell the other one that
it cannot establish new subflows to the initial IP address and port by
setting the 'C' flag [1]. Doing so makes sense when the sender is behind
a strict NAT, operating behind a legacy Layer 4 load balancer, or using
anycast IP address for example.
When this 'C' flag is set, the path-managers must then not try to
establish new subflows to the other peer's initial IP address and port.
The in-kernel PM has access to this info, but the userspace PM didn't.
The RFC8684 [1] is strict about that:
(...) therefore the receiver MUST NOT try to open any additional
subflows toward this address and port.
So it is important to tell the userspace about that as it is responsible
for the respect of this flag.
When a new connection is created and established, the Netlink events
now contain the existing but not currently used 'flags' attribute. When
MPTCP_PM_EV_FLAG_DENY_JOIN_ID0 is set, it means no other subflows
to the initial IP address and port -- info that are also part of the
event -- can be established.
Link: https://datatracker.ietf.org/doc/html/rfc8684#section-3.1-20.6 [1]
Fixes: 702c2f646d42 ("mptcp: netlink: allow userspace-driven subflow establishment")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/532
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250912-net-mptcp-pm-uspace-deny_join_id0-v1-2-40171884ade8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce qcomtee_object, which represents an object in both QTEE and
the kernel. QTEE clients can invoke an instance of qcomtee_object to
access QTEE services. If this invocation produces a new object in QTEE,
an instance of qcomtee_object will be returned.
Similarly, QTEE can request services from by issuing a callback
request, which invokes an instance of qcomtee_object.
Implement initial support for exporting qcomtee_object to userspace
and QTEE, enabling the invocation of objects hosted in QTEE and userspace
through the TEE subsystem.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Harshal Dev <quic_hdev@quicinc.com>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Amirreza Zarrabi <amirreza.zarrabi@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
|
|
Increase TEE_MAX_ARG_SIZE to accommodate worst-case scenarios where
additional buffer space is required to pass all arguments to TEE.
This change is necessary for upcoming support for Qualcomm TEE, which
requires a larger buffer for argument marshaling.
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Tested-by: Harshal Dev <quic_hdev@quicinc.com>
Signed-off-by: Amirreza Zarrabi <amirreza.zarrabi@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
|
|
The TEE subsystem allows session-based access to trusted services,
requiring a session to be established to receive a service. This
is not suitable for an environment that represents services as objects.
An object supports various operations that a client can invoke,
potentially generating a result or a new object that can be invoked
independently of the original object.
Add TEE_IOCTL_PARAM_ATTR_TYPE_OBJREF_INPUT/OUTPUT/INOUT to represent an
object. Objects may reside in either TEE or userspace. To invoke an
object in TEE, introduce a new ioctl. Use the existing SUPPL_RECV and
SUPPL_SEND to invoke an object in userspace.
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Harshal Dev <quic_hdev@quicinc.com>
Signed-off-by: Amirreza Zarrabi <amirreza.zarrabi@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
|
|
For drivers that can transfer data to the TEE without using shared
memory from client, it is necessary to receive the user address
directly, bypassing any processing by the TEE subsystem. Introduce
TEE_IOCTL_PARAM_ATTR_TYPE_UBUF_INPUT/OUTPUT/INOUT to represent
userspace buffers.
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Harshal Dev <quic_hdev@quicinc.com>
Signed-off-by: Amirreza Zarrabi <amirreza.zarrabi@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jenswi/linux-tee into soc/drivers
TEE protected DMA-bufs for v6.18
- Allocates protected DMA-bufs from a DMA-heap instantiated from the TEE
subsystem.
- The DMA-heap uses a protected memory pool provided by the backend TEE
driver, allowing it to choose how to allocate the protected physical
memory.
- Three use-cases (Secure Video Playback, Trusted UI, and Secure Video
Recording) have been identified so far to serve as examples of what
can be expected.
- The use-cases have predefined DMA-heap names,
"protected,secure-video", "protected,trusted-ui", and
"protected,secure-video-record". The backend driver registers protected
memory pools for the use-cases it supports.
* tag 'tee-prot-dma-buf-for-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jenswi/linux-tee:
optee: smc abi: dynamic protected memory allocation
optee: FF-A: dynamic protected memory allocation
optee: support protected memory allocation
tee: add tee_shm_alloc_dma_mem()
tee: new ioctl to a register tee_shm from a dmabuf file descriptor
tee: refactor params_from_user()
tee: implement protected DMA-heap
dma-buf: dma-heap: export declared functions
optee: sync secure world ABI headers
Link: https://lore.kernel.org/r/20250912101752.GA1453408@rayden
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
INPUT_PROP_HAPTIC_TOUCHPAD property is to be set for a device with simple
haptic capabilities.
Signed-off-by: Angela Czubak <aczubak@google.com>
Co-developed-by: Jonathan Denose <jdenose@google.com>
Signed-off-by: Jonathan Denose <jdenose@google.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
FF_HAPTIC effect type can be used to trigger haptic feedback with HID
simple haptic usages.
Signed-off-by: Angela Czubak <aczubak@google.com>
Co-developed-by: Jonathan Denose <jdenose@google.com>
Signed-off-by: Jonathan Denose <jdenose@google.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
Currently, the kexec_file_load syscall on x86 does not support passing a
device tree blob to the new kernel. Some embedded x86 systems use device
trees. On these systems, failing to pass a device tree to the new kernel
causes a boot failure.
To add support for this, we copy the behavior of ARM64 and PowerPC and
copy the current boot's device tree blob for use in the new kernel. We do
this on x86 by passing the device tree blob as a setup_data entry in
accordance with the x86 boot protocol.
This behavior is gated behind the KEXEC_FILE_FORCE_DTB flag.
Link: https://lkml.kernel.org/r/20250805211527.122367-3-makb@juniper.net
Signed-off-by: Brian Mak <makb@juniper.net>
Cc: Alexander Graf <graf@amazon.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Dave Young <dyoung@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Let's allow for making MADV_COLLAPSE succeed on areas that neither have
VM_HUGEPAGE nor VM_NOHUGEPAGE when we have THP disabled unless explicitly
advised (PR_THP_DISABLE_EXCEPT_ADVISED).
MADV_COLLAPSE is a clear advice that we want to collapse.
Note that we still respect the VM_NOHUGEPAGE flag, just like
MADV_COLLAPSE always does. So consequently, MADV_COLLAPSE is now only
refused on VM_NOHUGEPAGE with PR_THP_DISABLE_EXCEPT_ADVISED,
including for shmem.
Link: https://lkml.kernel.org/r/20250815135549.130506-4-usamaarif642@gmail.com
Co-developed-by: Usama Arif <usamaarif642@gmail.com>
Signed-off-by: Usama Arif <usamaarif642@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Barry Song <baohua@kernel.org>
Cc: Dev Jain <dev.jain@arm.com>
Cc: Jann Horn <jannh@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Mariano Pache <npache@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yafang <laoar.shao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "prctl: extend PR_SET_THP_DISABLE to only provide THPs when
advised", v5.
This will allow individual processes to opt-out of THP = "always" into THP
= "madvise", without affecting other workloads on the system. This has
been extensively discussed on the mailing list and has been summarized
very well by David in the first patch which also includes the links to
alternatives, please refer to the first patch commit message for the
motivation for this series.
Patch 1 adds the PR_THP_DISABLE_EXCEPT_ADVISED flag to implement this,
along with the MMF changes.
Patch 2 is a cleanup patch for tva_flags that will allow the forced
collapse case to be transmitted to vma_thp_disabled (which is done in
patch 3).
Patch 4 adds documentation for PR_SET_THP_DISABLE/PR_GET_THP_DISABLE.
Patches 6-7 implement the selftests for PR_SET_THP_DISABLE for completely
disabling THPs (old behaviour) and only enabling it at advise
(PR_THP_DISABLE_EXCEPT_ADVISED).
This patch (of 7):
People want to make use of more THPs, for example, moving from the "never"
system policy to "madvise", or from "madvise" to "always".
While this is great news for every THP desperately waiting to get
allocated out there, apparently there are some workloads that require a
bit of care during that transition: individual processes may need to
opt-out from this behavior for various reasons, and this should be
permitted without needing to make all other workloads on the system
similarly opt-out.
The following scenarios are imaginable:
(1) Switch from "none" system policy to "madvise"/"always", but keep THPs
disabled for selected workloads.
(2) Stay at "none" system policy, but enable THPs for selected
workloads, making only these workloads use the "madvise" or "always"
policy.
(3) Switch from "madvise" system policy to "always", but keep the
"madvise" policy for selected workloads: allocate THPs only when
advised.
(4) Stay at "madvise" system policy, but enable THPs even when not advised
for selected workloads -- "always" policy.
Once can emulate (2) through (1), by setting the system policy to
"madvise"/"always" while disabling THPs for all processes that don't want
THPs. It requires configuring all workloads, but that is a user-space
problem to sort out.
(4) can be emulated through (3) in a similar way.
Back when (1) was relevant in the past, as people started enabling THPs,
we added PR_SET_THP_DISABLE, so relevant workloads that were not ready yet
(i.e., used by Redis) were able to just disable THPs completely. Redis
still implements the option to use this interface to disable THPs
completely.
With PR_SET_THP_DISABLE, we added a way to force-disable THPs for a
workload -- a process, including fork+exec'ed process hierarchy. That
essentially made us support (1): simply disable THPs for all workloads
that are not ready for THPs yet, while still enabling THPs system-wide.
The quest for handling (3) and (4) started, but current approaches
(completely new prctl, options to set other policies per process,
alternatives to prctl -- mctrl, cgroup handling) don't look particularly
promising. Likely, the future will use bpf or something similar to
implement better policies, in particular to also make better decisions
about THP sizes to use, but this will certainly take a while as that work
just started.
Long story short: a simple enable/disable is not really suitable for the
future, so we're not willing to add completely new toggles.
While we could emulate (3)+(4) through (1)+(2) by simply disabling THPs
completely for these processes, this is a step backwards, because these
processes can no longer allocate THPs in regions where THPs were
explicitly advised: regions flagged as VM_HUGEPAGE. Apparently, that
imposes a problem for relevant workloads, because "not THPs" is certainly
worse than "THPs only when advised".
Could we simply relax PR_SET_THP_DISABLE, to "disable THPs unless not
explicitly advised by the app through MAD_HUGEPAGE"? *maybe*, but this
would change the documented semantics quite a bit, and the versatility to
use it for debugging purposes, so I am not 100% sure that is what we want
-- although it would certainly be much easier.
So instead, as an easy way forward for (3) and (4), add an option to
make PR_SET_THP_DISABLE disable *less* THPs for a process.
In essence, this patch:
(A) Adds PR_THP_DISABLE_EXCEPT_ADVISED, to be used as a flag in arg3
of prctl(PR_SET_THP_DISABLE) when disabling THPs (arg2 != 0).
prctl(PR_SET_THP_DISABLE, 1, PR_THP_DISABLE_EXCEPT_ADVISED).
(B) Makes prctl(PR_GET_THP_DISABLE) return 3 if
PR_THP_DISABLE_EXCEPT_ADVISED was set while disabling.
Previously, it would return 1 if THPs were disabled completely. Now
it returns the set flags as well: 3 if PR_THP_DISABLE_EXCEPT_ADVISED
was set.
(C) Renames MMF_DISABLE_THP to MMF_DISABLE_THP_COMPLETELY, to express
the semantics clearly.
Fortunately, there are only two instances outside of prctl() code.
(D) Adds MMF_DISABLE_THP_EXCEPT_ADVISED to express "no THP except for VMAs
with VM_HUGEPAGE" -- essentially "thp=madvise" behavior
Fortunately, we only have to extend vma_thp_disabled().
(E) Indicates "THP_enabled: 0" in /proc/pid/status only if THPs are
disabled completely
Only indicating that THPs are disabled when they are really disabled
completely, not only partially.
For now, we don't add another interface to obtained whether THPs
are disabled partially (PR_THP_DISABLE_EXCEPT_ADVISED was set). If
ever required, we could add a new entry.
The documented semantics in the man page for PR_SET_THP_DISABLE "is
inherited by a child created via fork(2) and is preserved across
execve(2)" is maintained. This behavior, for example, allows for
disabling THPs for a workload through the launching process (e.g., systemd
where we fork() a helper process to then exec()).
For now, MADV_COLLAPSE will *fail* in regions without VM_HUGEPAGE and
VM_NOHUGEPAGE. As MADV_COLLAPSE is a clear advise that user space thinks
a THP is a good idea, we'll enable that separately next (requiring a bit
of cleanup first).
There is currently not way to prevent that a process will not issue
PR_SET_THP_DISABLE itself to re-enable THP. There are not really known
users for re-enabling it, and it's against the purpose of the original
interface. So if ever required, we could investigate just forbidding to
re-enable them, or make this somehow configurable.
Link: https://lkml.kernel.org/r/20250815135549.130506-1-usamaarif642@gmail.com
Link: https://lkml.kernel.org/r/20250815135549.130506-2-usamaarif642@gmail.com
Acked-by: Zi Yan <ziy@nvidia.com>
Acked-by: Usama Arif <usamaarif642@gmail.com>
Tested-by: Usama Arif <usamaarif642@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Usama Arif <usamaarif642@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Dev Jain <dev.jain@arm.com>
Cc: Jann Horn <jannh@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Mariano Pache <npache@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yafang <laoar.shao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The zone_reclaim_mode API controls the reclaim behavior when a node runs
out of memory. Contrary to its user-facing name, it is internally
referred to as "node_reclaim_mode".
This can be confusing. But because we cannot change the name of the API
since it has been in place since at least 2.6, let's try to be more
explicit about what the behavior of this API is.
Change the description to clarify what zone reclaim entails, and be
explicit about the RECLAIM_ZONE bit, whose purpose has led to some
confusion in the past already [1] [2].
While at it, also soften the warning about changing these bits.
[joshua.hahnjy@gmail.com: remove the reference to the vm.zone_reclaim_mode sysctl as an ABI]
Link: https://lkml.kernel.org/r/20250806134404.2000234-1-joshua.hahnjy@gmail.com
Link: https://lkml.kernel.org/r/20250805205048.1518453-1-joshua.hahnjy@gmail.com
Link: https://lore.kernel.org/linux-mm/1579005573-58923-1-git-send-email-alex.shi@linux.alibaba.com/ [1]
Link: https://lore.kernel.org/linux-mm/20200626003459.D8E015CA@viggo.jf.intel.com/ [2]
Signed-off-by: Joshua Hahn <joshua.hahnjy@gmail.com>
Acked-by: SeongJae Park <sj@kernel.org>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Huang Ying <ying.huang@linux.alibaba.com>
Acked-by: Zi Yan <ziy@nvidia.com>
Acked-by: Byungchul Park <byungchul@sk.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Byungchul Park <byungchul@sk.com>
Cc: Gregory Price <gourry@gourry.net>
Cc: Mathew Brost <matthew.brost@intel.com>
Cc: Rakie Kim <rakie.kim@sk.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Linux 6.17-rc3
|
|
Add new IIO modifiers to support power and energy measurement devices:
Power modifiers:
- IIO_MOD_ACTIVE: Real power consumed by the load
- IIO_MOD_REACTIVE: Power that oscillates between source and load
- IIO_MOD_APPARENT: Magnitude of complex power
Signal quality modifiers:
- IIO_MOD_RMS: Root Mean Square value
Additionally adds:
- IIO_CHAN_INFO_POWERFACTOR: Power factor channel info type for
representing the ratio of active power to apparent power
These modifiers enable proper representation of power measurement
devices like energy meters and power analyzers.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for IIO_ALTCURRENT channel type to distinguish AC current
measurements from DC current measurements. This follows the same pattern
as IIO_VOLTAGE and IIO_ALTVOLTAGE.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Florian Westphal says:
====================
netfilter: updates for net-next
1) Don't respond to ICMP_UNREACH errors with another ICMP_UNREACH
error.
2) Support fetching the current bridge ethernet address.
This allows a more flexible approach to packet redirection
on bridges without need to use hardcoded addresses. From
Fernando Fernandez Mancera.
3) Zap a few no-longer needed conditionals from ipvs packet path
and convert to READ/WRITE_ONCE to avoid KCSAN warnings.
From Zhang Tengfei.
4) Remove a no-longer-used macro argument in ipset, from Zhen Ni.
* tag 'nf-next-25-09-11' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: nf_reject: don't reply to icmp error messages
ipvs: Use READ_ONCE/WRITE_ONCE for ipvs->enable
netfilter: nft_meta_bridge: introduce NFT_META_BRI_IIFHWADDR support
netfilter: ipset: Remove unused htable_bits in macro ahash_region
selftest:net: fixed spelling mistakes
====================
Link: https://patch.msgid.link/20250911143819.14753-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The previous patches introduced a new option, BR_BOOLOPT_FDB_LOCAL_VLAN_0.
When enabled, it has local FDB entries installed only on VLAN 0, instead of
duplicating them across all VLANs.
In this patch, add the corresponding UAPI toggle, and the code for turning
the feature on and off.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/ea99bfb10f687fa58091e6e1c2f8acc33f47ca45.1757004393.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Plenty of things going on, notably:
- iwlwifi: major cleanups/rework
- brcmfmac: gets AP isolation support
- mac80211: gets more S1G support
* tag 'wireless-next-2025-09-11' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (94 commits)
wifi: mwifiex: fix endianness handling in mwifiex_send_rgpower_table
wifi: cfg80211: Remove the redundant wiphy_dev
wifi: mac80211: fix incorrect comment
wifi: cfg80211: update the time stamps in hidden ssid
wifi: mac80211: Fix HE capabilities element check
wifi: mac80211: add tx_handlers_drop statistics to ethtool
wifi: mac80211: fix reporting of all valid links in sta_set_sinfo()
wifi: iwlwifi: mld: CHANNEL_SURVEY_NOTIF is always supported
wifi: iwlwifi: mld: remove support of iwl_esr_mode_notif version 1
wifi: iwlwifi: mld: remove support from of sta cmd version 1
wifi: iwlwifi: mld: remove support of roc cmd version 5
wifi: iwlwifi: mld: remove support of mac cmd ver 2
wifi: iwlwifi: mld: don't consider phy cmd version 5
wifi: iwlwifi: implement wowlan status notification API update
wifi: iwlwifi: fw: Add ASUS to PPAG and TAS list
wifi: iwlwifi: add kunit tests for nvm parse
wifi: iwlwifi: api: add a flag to iwl_link_ctx_modify_flags
wifi: iwlwifi: pcie: move ltr_enabled to the specific transport
wifi: iwlwifi: pcie: move pm_support to the specific transport
wifi: iwlwifi: rename iwl_finish_nic_init
...
====================
Link: https://patch.msgid.link/20250911100854.20445-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Expose the input bridge interface ethernet address so it can be used to
redirect the packet to the receiving physical device for processing.
Tested with nft command line tool.
table bridge nat {
chain PREROUTING {
type filter hook prerouting priority 0; policy accept;
ether daddr de:ad:00:00:be:ef meta pkttype set host ether daddr set meta ibrhwdr accept
}
}
Joint work with Pablo Neira.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Add a userspace API to create a tee_shm object that refers to a dmabuf
reference.
Userspace registers the dmabuf file descriptor as in a tee_shm object.
The registration is completed with a tee_shm returned file descriptor.
Userspace is free to close the dmabuf file descriptor after it has been
registered since all the resources are now held via the new tee_shm
object.
Closing the tee_shm file descriptor will eventually release all
resources used by the tee_shm object when all references are released.
The new IOCTL, TEE_IOC_SHM_REGISTER_FD, supports dmabuf references to
physically contiguous memory buffers. Dmabuf references acquired from
the TEE DMA-heap can be used as protected memory for Secure Video Path
and such use cases. It depends on the TEE and the TEE driver if dmabuf
references acquired by other means can be used.
A new tee_shm flag is added to identify tee_shm objects built from a
registered dmabuf, TEE_SHM_DMA_BUF.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Olivier Masse <olivier.masse@nxp.com>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
|
|
Replace hverkuil@xs4all.nl by hverkuil@kernel.org.
Signed-off-by: Hans Verkuil <hverkuil@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Replace hansverk@cisco.com by hverkuil@kernel.org.
Signed-off-by: Hans Verkuil <hverkuil@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Introduce a new netlink attribute 'actor_port_prio' to allow setting
the LACP actor port priority on a per-slave basis. This extends the
existing bonding infrastructure to support more granular control over
LACP negotiations.
The priority value is embedded in LACPDU packets and will be used by
subsequent patches to influence aggregator selection policies.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20250902064501.360822-2-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce two new ioctl commands, PTP_SYS_OFFSET_PRECISE_CYCLES and
PTP_SYS_OFFSET_EXTENDED_CYCLES, to allow user space to access the
raw free-running cycle counter from PTP devices.
These ioctls are variants of the existing PRECISE and EXTENDED
offset queries, but instead of returning device time in realtime,
they return the raw cycle counter value.
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://patch.msgid.link/1755008228-88881-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are many parameters users might want to query about io_uring like
available request types or the ring sizes. This patch introduces an
interface for such slow path queries.
It was written with several requirements in mind:
- Can be used with or without an io_uring instance. Asking for supported
setup flags before creating an instance as well as qeurying info about
an already created ring are valid use cases.
- Should be moderately fast. For example, users might use it to
periodically retrieve ring attributes at runtime. As a consequence,
it should be able to query multiple attributes in a single syscall.
- Backward and forward compatible.
- Should be reasobably easy to use.
- Reduce the kernel code size for introducing new query types.
It's implemented as a new registration opcode IORING_REGISTER_QUERY.
The user passes one or more query strutctures linked together, each
represented by struct io_uring_query_hdr. The header stores common
control fields needed for processing and points to query type specific
information.
The header contains
- The query type
- The result field, which on return contains the error code for the query
- Pointer to the query type specific information
- The size of the query structure. The kernel will only populate up to
the size, which helps with backward compatibility. The kernel can also
reduce the size, so if the current kernel is older than the inteface
the user tries to use, it'll get only the supported bits.
- next_entry field is used to chain multiple queries.
Apart from common registeration syscall failures, it can only immediately
return an error code in case when the headers are incorrect or any
other addresses and invalid. That usually mean that the userspace
doesn't use the API right and should be corrected. All query type
specific errors are returned in the header's result field.
As an example, the patch adds a single query type for now, i.e.
IO_URING_QUERY_OPCODES, which tells what register / request / etc.
opcodes are supported, but there are particular plans to extend it.
Note: there is a request probing interface via IORING_REGISTER_PROBE,
but it's a mess. It requires the user to create a ring first, it only
works for requests, and requires dynamic allocations.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Some fuse servers need to prune their caches, which can only be done if the
kernel's own dentry/inode caches are pruned first to avoid dangling
references.
Add FUSE_NOTIFY_PRUNE, which takes an array of node ID's to try and get rid
of. Inodes with active references are skipped.
A similar functionality is already provided by FUSE_NOTIFY_INVAL_ENTRY with
the FUSE_EXPIRE_ONLY flag. Differences in the interface are
FUSE_NOTIFY_INVAL_ENTRY:
- can only prune one dentry
- dentry is determined by parent ID and name
- if inode has multiple aliases (cached hard links), then they would have
to be invalidated individually to be able to get rid of the inode
FUSE_NOTIFY_PRUNE:
- can prune multiple inodes
- inodes determined by their node ID
- aliases are taken care of automatically
Reviewed-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Constants that change value from version to version have no place in an
interface definition.
Hopefully this won't break anything.
Reviewed-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.17-rc5).
No conflicts.
Adjacent changes:
include/net/sock.h
c51613fa276f ("net: add sk->sk_drop_counters")
5d6b58c932ec ("net: lockless sock_i_ino()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When reporting an error, the AER driver prints the TLP Header / Prefix Log
only for errors enumerated in the AER_LOG_TLP_MASKS macro.
The macro was never amended since its introduction in 2006 with commit
6c2b374d7485 ("PCI-Express AER implemetation: AER core and aerdriver").
At the time, PCIe r1.1 was the latest spec revision.
Amend the macro with errors defined since then to avoid omitting the TLP
Header / Prefix Log for newer errors.
The order of the errors in AER_LOG_TLP_MASKS follows PCIe r1.1 sec 6.2.7
rather than 7.10.2, because only the former documents for which errors a
TLP Header / Prefix is logged. Retain this order. The section number is
still 6.2.7 in today's PCIe r7.0.
For Completion Timeouts, the TLP Header / Prefix is only logged if the
Completion Timeout Prefix / Header Log Capable bit is set in the AER
Capabilities and Control register. Introduce a tlp_header_logged() helper
to check whether the TLP Header / Prefix Log is populated and use it in
the two places which currently match against AER_LOG_TLP_MASKS directly.
For Uncorrectable Internal Errors, logging of the TLP Header / Prefix is
optional per PCIe r7.0 sec 6.2.7. If needed, drivers could indicate
through a flag whether devices are capable and tlp_header_logged() could
then check that flag.
pcitools introduced macros for newer errors with commit 144b0911cc0b
("ls-ecaps: extend decode support for more fields for AER CE and UE
status"):
https://git.kernel.org/pub/scm/utils/pciutils/pciutils.git/commit/?id=144b0911cc0b
Unfortunately some of those macros are overly long:
PCI_ERR_UNC_POISONED_TLP_EGRESS
PCI_ERR_UNC_DMWR_REQ_EGRESS_BLOCKED
PCI_ERR_UNC_IDE_CHECK
PCI_ERR_UNC_MISR_IDE_TLP
PCI_ERR_UNC_PCRC_CHECK
PCI_ERR_UNC_TLP_XLAT_EGRESS_BLOCKED
This seems unsuitable for <linux/pci_regs.h>, so shorten to:
PCI_ERR_UNC_POISON_BLK
PCI_ERR_UNC_DMWR_BLK
PCI_ERR_UNC_IDE_CHECK
PCI_ERR_UNC_MISR_IDE
PCI_ERR_UNC_PCRC_CHECK
PCI_ERR_UNC_XLAT_BLK
Note that some of the existing macros in <linux/pci_regs.h> do not match
exactly with pcitools (e.g. PCI_ERR_UNC_SDES versus PCI_ERR_UNC_SURPDN),
so it does not seem mandatory for them to be identical.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/5f707caf1260bd8f15012bb032f7da9a9b898aba.1756712066.git.lukas@wunner.de
|
|
Assure user-space only modifies attributes for NL80211_CMD_SET_BSS
that are supported by the driver. This stricter checking is only done
when user-space commits to it by including NL80211_ATTR_BSS_PARAM.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250817190435.1495094-4-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The so-called fullmac devices rely on firmware functionality and/or API to
change BSS parameters. Today there are limited drivers supporting the
nl80211 primitive, but they only handle a subset of the bss parameters
passed if any. The mac80211 driver does handle all parameters and stores
their configured values. Some of the BSS parameters were already conditional
by wiphy->features. For these the wiphy->bss_param_support and wiphy->features
fields are silently aligned in wiphy_register(). Maybe better to issue a warning
instead when they are misaligned.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20250817190435.1495094-2-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add new attributes to support EHT MCS/NSS Tx rates and EHT GI/LTF.
Parse EHT fixed MCS/NSS Tx rates and EHT GI/LTF values passed by the
userspace, validate and add as part of cfg80211_bitrate_mask.
MCS mask is constructed by new function, eht_build_mcs_mask(). Max NSS
supported for MCS rates of 7, 9, 11 and 13 is utilized to set MCS
bitmask for each NSS. MCS rates 14, and 15 if supported, are set only
for NSS = 0.
Co-developed-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Link: https://patch.msgid.link/20250815213011.2704803-1-muna.sinada@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
An S1G TIM PVB is encoded differently compared to a non-s1g TIM PVB.
As the AP dictates which encoding mode it uses, here we only implement
block bitmap encoding. This is the default encoding mode used by
all current vendor implementations.
Additionally, S1G has a maximum AID count of 8192, however we are
limiting the current implementation to 1600. This has no resemblence
to the standard and is purely an implementation detail. The reason for
this is due to the TIM elements maximum length of 255. This allows for,
at most, 25 encoded blocks for a PVB encoded with block bitmap. Support
for the maximum of 8192 AIDs will require an implementation of page slicing
to be added to mac80211.
As a result, we perform extra validation on both the STA and AP side
when receiving an AID as an S1G interface.
Add support for block bitmap encoding for an S1G AP and limit the
maximum AID count to 1600 for the current mac80211 implementations.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250725132221.258217-2-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Move some fields closer to where they are used, add missing tabs
and remove an extra newline.
Signed-off-by: Paul Kocialkowski <paulk@sys-base.io>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
This new attribute is supposed to be used instead of NFTA_DEVICE_NAME
for simple wildcard interface specs. It holds a NUL-terminated string
representing an interface name prefix to match on.
While kernel code to distinguish full names from prefixes in
NFTA_DEVICE_NAME is simpler than this solution, reusing the existing
attribute with different semantics leads to confusion between different
versions of kernel and user space though:
* With old kernels, wildcards submitted by user space are accepted yet
silently treated as regular names.
* With old user space, wildcards submitted by kernel may cause crashes
since libnftnl expects NUL-termination when there is none.
Using a distinct attribute type sanitizes these situations as the
receiving part detects and rejects the unexpected attribute nested in
*_HOOK_DEVS attributes.
Fixes: 6d07a289504a ("netfilter: nf_tables: Support wildcard netdev hook specs")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
FUSE_INIT has always been asynchronous with mount. That means that the
server processed this request after the mount syscall returned.
This means that FUSE_INIT can't supply the root inode's ID, hence it
currently has a hardcoded value. There are other limitations such as not
being able to perform getxattr during mount, which is needed by selinux.
To remove these limitations allow server to process FUSE_INIT while
initializing the in-core super block for the fuse filesystem. This can
only be done if the server is prepared to handle this, so add
FUSE_DEV_IOC_SYNC_INIT ioctl, which
a) lets the server know whether this feature is supported, returning
ENOTTY othewrwise.
b) lets the kernel know to perform a synchronous initialization
The implementation is slightly tricky, since fuse_dev/fuse_conn are set up
only during super block creation. This is solved by setting the private
data of the fuse device file to a special value ((struct fuse_dev *) 1) and
waiting for this to be turned into a proper fuse_dev before commecing with
operations on the device file.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Create a new audit record AUDIT_MAC_OBJ_CONTEXTS.
An example of the MAC_OBJ_CONTEXTS record is:
type=MAC_OBJ_CONTEXTS
msg=audit(1601152467.009:1050):
obj_selinux=unconfined_u:object_r:user_home_t:s0
When an audit event includes a AUDIT_MAC_OBJ_CONTEXTS record
the "obj=" field in other records in the event will be "obj=?".
An AUDIT_MAC_OBJ_CONTEXTS record is supplied when the system has
multiple security modules that may make access decisions based
on an object security context.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
[PM: subj tweak, audit example readability indents]
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Replace the single skb pointer in an audit_buffer with a list of
skb pointers. Add the audit_stamp information to the audit_buffer as
there's no guarantee that there will be an audit_context containing
the stamp associated with the event. At audit_log_end() time create
auxiliary records as have been added to the list. Functions are
created to manage the skb list in the audit_buffer.
Create a new audit record AUDIT_MAC_TASK_CONTEXTS.
An example of the MAC_TASK_CONTEXTS record is:
type=MAC_TASK_CONTEXTS
msg=audit(1600880931.832:113)
subj_apparmor=unconfined
subj_smack=_
When an audit event includes a AUDIT_MAC_TASK_CONTEXTS record the
"subj=" field in other records in the event will be "subj=?".
An AUDIT_MAC_TASK_CONTEXTS record is supplied when the system has
multiple security modules that may make access decisions based on a
subject security context.
Refactor audit_log_task_context(), creating a new audit_log_subj_ctx().
This is used in netlabel auditing to provide multiple subject security
contexts as necessary.
Suggested-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
[PM: subj tweak, audit example readability indents]
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.17-rc4).
No conflicts.
Adjacent changes:
drivers/net/ethernet/intel/idpf/idpf_txrx.c
02614eee26fb ("idpf: do not linearize big TSO packets")
6c4e68480238 ("idpf: remove obsolete stashing code")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For a user mode library to avoid generating SIGPIPE signals (e.g.
because this behaviour is not portable across operating systems) is
cumbersome. It is generally bad form to change the process-wide signal
mask in a library, so a local solution is needed instead.
For I/O performed directly using system calls (synchronous or readiness
based asynchronous) this currently involves applying a thread-specific
signal mask before the operation and reverting it afterwards. This can be
avoided when it is known that the file descriptor refers to neither a
pipe nor a socket, but a conservative implementation must always apply
the mask. This incurs the cost of two additional system calls. In the
case of sockets, the existing MSG_NOSIGNAL flag can be used with send.
For asynchronous I/O performed using io_uring, currently the only option
(apart from MSG_NOSIGNAL for sockets), is to mask SIGPIPE entirely in the
call to io_uring_enter. Thankfully io_uring_enter takes a signal mask, so
only a single syscall is needed. However, copying the signal mask on
every call incurs a non-zero performance penalty. Furthermore, this mask
applies to all completions, meaning that if the non-signaling behaviour
is desired only for some subset of operations, the desired signals must
be raised manually from user-mode depending on the completed operation.
Add RWF_NOSIGNAL flag for pwritev2. This flag prevents the SIGPIPE signal
from being raised when writing on disconnected pipes or sockets. The flag
is handled directly by the pipe filesystem and converted to the existing
MSG_NOSIGNAL flag for sockets.
Signed-off-by: Lauri Vasama <git@vasama.org>
Link: https://lore.kernel.org/20250827133901.1820771-1-git@vasama.org
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
ASPEED BMC IC has 2 different display engines. Please find AST2600's
datasheet to get detailed information.
1. VGA on PCIe
2. SoC Display (GFX)
By default, video engine (VE) will capture video from VGA. This patch
adds an option to capture video from GFX with standard ioctl,
vidioc_s_input.
An enum, aspeed_video_input, is added for this purpose.
enum aspeed_video_input {
VIDEO_INPUT_VGA = 0,
VIDEO_INPUT_GFX,
VIDEO_INPUT_MAX
};
To test this feature, you will need to enable GFX first. Please refer to
ASPEED's SDK_User_Guide, 6.3.x Soc Display driver, for more information.
In your application, you will need to use v4l2 ioctl, VIDIOC_S_INPUT, as
below to select before start streaming.
int rc;
struct v4l2_input input;
input.index = VIDEO_INPUT_GFX;
rc = ioctl(fd, VIDIOC_S_INPUT, &input);
if (rc < 0)
{
...
}
Link: https://github.com/AspeedTech-BMC/openbmc/releases
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
[hverkuil: split up three overly long lines]
|
|
Some definitions use a tab after the define keyword instead of the
usual single space. Replace it for better consistency.
Signed-off-by: Paul Kocialkowski <paulk@sys-base.io>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The colorimetry controls class is defined after the stateless codec
class at the top of the controls header. It is currently defined in
the middle of stateless codec controls.
Move the colorimetry controls after the stateless codec controls,
at the end of the file.
Signed-off-by: Paul Kocialkowski <paulk@sys-base.io>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
|
|
The uAPI stddef header includes compiler_types.h, a kernel-only
header, to make sure that kernel definitions of annotations
like __counted_by() take precedence.
There is a hack in scripts/headers_install.sh which strips includes
of compiler.h and compiler_types.h when installing uAPI headers.
While explicit handling makes sense for compiler.h, which is included
all over the uAPI, compiler_types.h is only included by stddef.h
(within the uAPI, obviously it's included in kernel code a lot).
Remove the stripping from scripts/headers_install.sh and wrap
the include of compiler_types.h in #ifdef __KERNEL__ instead.
This should be equivalent functionally, but is easier to understand
to a casual reader of the code. It also makes it easier to work
with kernel headers directly from under tools/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250825201828.2370083-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This adds support for setting IORING_NOP_CQE32 as a flag for a NOP
command, in which case a 32b CQE will be posted rather than a regular
one. This is the default if the ring has been setup with
IORING_SETUP_CQE32. If the ring has been setup with
IORING_SETUP_CQE_MIXED, then 16b CQEs will be posted without this flag
set, and 32b CQEs if this flag is set. For the latter case, sqe->off is
what will be posted as cqe->big_cqe[0] and sqe->addr is what will be
posted as cqe->big_cqe[1].
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Normal rings support 16b CQEs for posting completions, while certain
features require the ring to be configured with IORING_SETUP_CQE32, as
they need to convey more information per completion. This, in turn,
makes ALL the CQEs be 32b in size. This is somewhat wasteful and
inefficient, particularly when only certain CQEs need to be of the
bigger variant.
This adds support for setting up a ring with mixed CQE sizes, using
IORING_SETUP_CQE_MIXED. When setup in this mode, CQEs posted to the ring
may be either 16b or 32b in size. If a CQE is 32b in size, then
IORING_CQE_F_32 is set in the CQE flags to indicate that this is the
case. If this flag isn't set, the CQE is the normal 16b variant.
CQEs on these types of mixed rings may also have IORING_CQE_F_SKIP set.
This can happen if the ring is one (small) CQE entry away from wrapping,
and an attempt is made to post a 32b CQE. As CQEs must be contigious in
the CQ ring, a 32b CQE cannot wrap the ring. For this case, a single
dummy CQE is posted with the SKIP flag set. The application should
simply ignore those.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
