| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds transmit power setting type and transmit power level attributes
to NL80211_CMD_SET_WIPHY in order to facilitate adjusting of the transmit power
level of the device.
The added attributes allow selection of automatic, limited or fixed transmit
power level, with the level definable in signed mBm format.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In preparation for a TX power setting interface in the nl80211, change the
.set_tx_power function to use mBm units instead of dBm for greater accuracy and
smaller power levels.
Also, already in advance move the tx_power_setting enumeration to nl80211.
This change affects the .tx_set_power function prototype. As a result, the
corresponding changes are needed to modules using it. These are mac80211,
iwmc3200wifi and rndis_wlan.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This mechanism introduced in this patch applies (at least) for hardware
designs using a single shared antenna for both WLAN and BT. In these designs,
the antenna must be toggled between WLAN and BT.
In those hardware, managing WLAN co-existence with Bluetooth requires WLAN
full power save whenever there is Bluetooth activity in order for WLAN to be
able to periodically relinquish the antenna to be used for BT. This is because
BT can only access the shared antenna when WLAN is idle or asleep.
Some hardware, for instance the wl1271, are able to indicate to the host
whenever there is BT traffic. In essence, the hardware will send an indication
to the host whenever there is, for example, SCO traffic or A2DP traffic, and
will send another indication when the traffic is over.
The hardware gets information of Bluetooth traffic via hardware co-existence
control lines - these lines are used to negotiate the shared antenna
ownership. The hardware will give the antenna to BT whenever WLAN is sleeping.
This patch adds the interface to mac80211 to facilitate temporarily disabling
of dynamic power save as per request of the WLAN driver. This interface will
immediately force WLAN to full powersave, hence allowing BT coexistence as
described above.
In these kind of shared antenna desings, when WLAN powersave is fully disabled,
Bluetooth will not work simultaneously with WLAN at all. This patch does not
address that problem. This interface will not change PSM state, so if PSM is
disabled it will remain so. Solving this problem requires knowledge about BT
state, and is best done in user-space.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The ps-qos latency handling is broken. It uses predetermined latency values
to select specific dynamic PS timeouts. With common AP configurations, these
values overlap with beacon interval and are therefore essentially useless
(for network latencies less than the beacon interval, PSM is disabled.)
This patch remedies the problem by replacing the predetermined network latency
values with one high value (1900ms) which is used to go trigger full psm. For
backwards compatibility, the value 2000ms is still mapped to a dynamic ps
timeout of 100ms.
Currently also the mac80211 internal value for storing user space configured
dynamic PSM values is incorrectly in the driver visible ieee80211_conf struct.
Move it to the ieee80211_local struct.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is a circular locking dependency when configuring the
hardware ARP filters on association, occurring when flushing the mac80211
workqueue. This is what happens:
[ 92.026800] =======================================================
[ 92.030507] [ INFO: possible circular locking dependency detected ]
[ 92.030507] 2.6.34-04781-g2b2c009 #85
[ 92.030507] -------------------------------------------------------
[ 92.030507] modprobe/5225 is trying to acquire lock:
[ 92.030507] ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8105b5c0>] flush_workq
ueue+0x0/0xb0
[ 92.030507]
[ 92.030507] but task is already holding lock:
[ 92.030507] (rtnl_mutex){+.+.+.}, at: [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507]
[ 92.030507] which lock already depends on the new lock.
[ 92.030507]
[ 92.030507]
[ 92.030507] the existing dependency chain (in reverse order) is:
[ 92.030507]
[ 92.030507] -> #2 (rtnl_mutex){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff81341754>] mutex_lock_nested+0x44/0x300
[ 92.030507] [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507] [<ffffffffa022d47c>] ieee80211_assoc_done+0x6c/0xe0 [mac80211]
[ 92.030507] [<ffffffffa022f2ad>] ieee80211_work_work+0x31d/0x1280 [mac80211]
[ 92.030507] -> #1 ((&local->work_work)){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105a51a>] worker_thread+0x22a/0x370
[ 92.030507] [<ffffffff8105ecc6>] kthread+0x96/0xb0
[ 92.030507] [<ffffffff81003a94>] kernel_thread_helper+0x4/0x10
[ 92.030507]
[ 92.030507] -> #0 ((wiphy_name(local->hw.wiphy))){+.+.+.}:
[ 92.030507] [<ffffffff81075fdc>] __lock_acquire+0x1c0c/0x1d50
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105b60e>] flush_workqueue+0x4e/0xb0
[ 92.030507] [<ffffffffa023ff7b>] ieee80211_stop_device+0x2b/0xb0 [mac80211]
[ 92.030507] [<ffffffffa0231635>] ieee80211_stop+0x3e5/0x680 [mac80211]
The locking in this case is quite complex. Fix the problem by rewriting the
way the hardware ARP filter list is handled - i.e. make a copy of the address
list to the bss_conf struct, and provide that list to the hardware driver
when needed.
The current patch will enable filtering also in promiscuous mode. This may need
to be changed in the future.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds support to nl80211 and mac80211 to set basic rates when
joining/creating ibss network.
Original patch was posted by Johannes Berg on the linux-wireless posting list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The non-irqsafe aggregation start/stop done
callbacks are currently only used by ath9k_htc,
and can cause callbacks into the driver again.
This might lead to locking issues, which will
only get worse as we modify locking. To avoid
trouble, remove the non-irqsafe versions and
change ath9k_htc to use those instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix a whole bunch of kernel-doc warnings
and errors that crop up when running it on
mac80211 and cfg80211; the latter isn't
normally done so lots of bit-rot happened.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Now they are unnecessary. We can use the generic DMA API with any bus.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Gary Zambrano <zambrano@broadcom.com>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add dma_dev, a pointer to struct device, to struct ssb_device. We pass it
to the generic DMA API with SSB_BUSTYPE_PCI and SSB_BUSTYPE_SSB.
ssb_devices_register() sets up it properly.
This is preparation for replacing the ssb bus specific DMA API (ssb_dma_*)
with the generic DMA API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: Gary Zambrano <zambrano@broadcom.com>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
STA_NOTIFY_ADD and STA_NOTIFY_REMOVE have no users anymore,
and station addition/removal are indicated to drivers
using sta_add() and sta_remove(), which can sleep.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There's no sense in letting anything but internal
mac80211 functions set the initiator to anything
but WLAN_BACK_INITIATOR, since WLAN_BACK_RECIPIENT
is only valid when we have received a frame from
the peer, which we react to directly in mac80211.
The debugfs code I recently added got this wrong
as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some hardware allow extended filtering of ARP frames not intended for
the host. To perform such filtering, the hardware needs to know the current
IP address(es) of the host, bound to its interface.
Add support for ARP filtering to mac80211 by adding a new op to the driver
interface, allowing to configure the current IP addresses. This op is called
upon association with the currently configured address(es), and when
associated whenever the IP address(es) change.
This patch adds configuration of IPv4 addresses only, as IPv6 addresses don't
need ARP filtering.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There's a single use of this struct member, but
as it is write-only it clearly not necessary.
Thus we can free up some space here, even if we
don't need it right now it seems pointless to
carry around the variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When sending action frames, we want to verify
that we do that on the correct channel. However,
checking the channel type in addition can get in
the way, since the channel type could change on
the fly during an association, and it's not
useful to have the channel type anyway since it
has no effect on the transmission. Therefore,
make it optional to specify so that if wanted,
it can still be checked, but is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Walter Goldens <goldenstranger@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix kernel-doc warnings in mac80211.h:
Warning(include/net/mac80211.h:838): No description found for parameter 'ap_addr'
Warning(include/net/mac80211.h:1726): No description found for parameter 'get_survey'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reverts commit 03ceedea972a82d343fa5c2528b3952fa9e615d5.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix some issues introduced in batch skb dequeuing for input_pkt_queue.
The primary issue it that the queue head must be incremented only
after a packet has been processed, that is only after
__netif_receive_skb has been called. This is needed for the mechanism
to prevent OOO packet in RFS. Also when flushing the input_pkt_queue
and process_queue, the process queue should be done first to prevent
OOO packets.
Because the input_pkt_queue has been effectively split into two queues,
the calculation of the tail ptr is no longer correct. The correct value
would be head+input_pkt_queue->len+process_queue->len. To avoid
this calculation we added an explict input_queue_tail in softnet_data.
The tail value is simply incremented when queuing to input_pkt_queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-next-2.6
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits)
USB: remove unused usb_buffer_alloc and usb_buffer_free macros
usb: musb: update gfp/slab.h includes
USB: ftdi_sio: fix legacy SIO-device header
USB: kl5usb105: reimplement using generic framework
USB: kl5usb105: minor clean ups
USB: kl5usb105: fix memory leak
USB: io_ti: use kfifo to implement write buffering
USB: io_ti: remove unsused private counter
USB: ti_usb: use kfifo to implement write buffering
USB: ir-usb: fix incorrect write-buffer length
USB: aircable: fix incorrect write-buffer length
USB: safe_serial: straighten out read processing
USB: safe_serial: reimplement read using generic framework
USB: safe_serial: reimplement write using generic framework
usb-storage: always print quirks
USB: usb-storage: trivial debug improvements
USB: oti6858: use port write fifo
USB: oti6858: use kfifo to implement write buffering
USB: cypress_m8: use kfifo to implement write buffering
USB: cypress_m8: remove unused drain define
...
Fix up conflicts (due to usb_buffer_alloc/free renaming) in
drivers/input/tablet/acecad.c
drivers/input/tablet/kbtab.c
drivers/input/tablet/wacom_sys.c
drivers/media/video/gspca/gspca.c
sound/usb/usbaudio.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
|
|
* 'viafb-next' of git://git.lwn.net/linux-2.6: (35 commits)
viafb: move some include files to include/linux
viafb: Eliminate some global.h references
viafb: get rid of i2c debug cruft
viafb: fold via_io.h into via-core.h
viafb: Fix initialization error paths
viafb: Do not remove gpiochip under spinlock
viafb: make procfs entries optional
viafb: fix proc entry removal
viafb: improve misc register handling
viafb: replace inb/outb
viafb: move some modesetting functions to a seperate file
viafb: unify modesetting functions
viafb: Reserve framebuffer memory for the upcoming camera driver
viafb: Add a simple VX855 DMA engine driver
viafb: Add a simple interrupt management infrastructure
via: Rationalize vt1636 detection
viafb: Introduce viafb_find_i2c_adapter()
via: Do not attempt I/O on inactive I2C adapters
viafb: Turn GPIO and i2c into proper platform devices
viafb: Convert GPIO and i2c to the new indexed port ops
...
|
|
Now that all callers are converted over, remove the compatibility
functions and all is good.
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Lots of minor formatting cleanups in includes/usb/ to make checkpatch
happier.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Minor formatting changes to clean up the file.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Now on one uses this function and it seems useless,
so remove usb_find_device.
[tom@tom linux-2.6-next]$ grep -r -n -I usb_find_device ./
drivers/media/dvb/dvb-usb/dvb-usb-init.c:160:static struct
dvb_usb_device_description * dvb_usb_find_device(struct usb_device
*udev,struct dvb_usb_device_properties *props, int *cold)
drivers/media/dvb/dvb-usb/dvb-usb-init.c:230: if ((desc =
dvb_usb_find_device(udev,props,&cold)) == NULL) {
drivers/usb/core/usb.c:630: * usb_find_device - find a specific usb device in the system
drivers/usb/core/usb.c:642:struct usb_device *usb_find_device(u16 vendor_id, u16 product_id)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The FunctionFS is a USB composite function that can be used
with the composite framework to create an USB gadget.
>From kernel point of view it is just a composite function with
some unique behaviour. It may be added to an USB
configuration only after the user space driver has registered
by writing descriptors and strings (the user space program has
to provide the same information that kernel level composite
functions provide when they are added to the configuration).
>From user space point of view it is a file system which when
mounted provide an "ep0" file. User space driver need to
write descriptors and strings to that file. It does not need
to worry about endpoints, interfaces or strings numbers but
simply provide descriptors such as if the function was the
only one (endpoints and strings numbers starting from one and
interface numbers starting from core). The FunctionFS changes
numbers of those as needed also handling situation when
numbers differ in different configurations.
When descriptors and strings are written "ep#" files appear
(one for each declared endpoint) which handle communication on
a single endpoint. Again, FunctionFS takes care of the real
numbers and changing of the configuration (which means that
"ep1" file may be really mapped to (say) endpoint 3 (and when
configuration changes to (say) endpoint 2)). "ep0" is used
for receiving events and handling setup requests.
When all files are closed the function disables itself.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
New wait_event_interruptible{,_exclusive}_locked{,_irq} macros added.
They work just like versions without _locked* suffix but require the
wait queue's lock to be held. Also __wake_up_locked() is now exported
as to pair it with the above macros.
The use case of this new facility is when one uses wait queue's lock
to protect a data structure. This may be advantageous if the
structure needs to be protected by a spinlock anyway. In particular,
with additional spinlock the following code has to be used to wait
for a condition:
spin_lock(&data.lock);
...
for (ret = 0; !ret && !(condition); ) {
spin_unlock(&data.lock);
ret = wait_event_interruptible(data.wqh, (condition));
spin_lock(&data.lock);
}
...
spin_unlock(&data.lock);
This looks bizarre plus wait_event_interruptible() locks the wait
queue's lock anyway so there is a unlock+lock sequence where it could
be avoided.
To avoid those problems and benefit from wait queue's lock, a code
similar to the following should be used:
/* Waiting */
spin_lock(&data.wqh.lock);
...
ret = wait_event_interruptible_locked(data.wqh, (condition));
...
spin_unlock(&data.wqh.lock);
/* Waiting exclusively */
spin_lock(&data.whq.lock);
...
ret = wait_event_interruptible_exclusive_locked(data.whq, (condition));
...
spin_unlock(&data.whq.lock);
/* Waking up */
spin_lock(&data.wqh.lock);
...
wake_up_locked(&data.wqh);
...
spin_unlock(&data.wqh.lock);
When spin_lock_irq() is used matching versions of macros need to be
used (*_locked_irq()).
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove multi-urb write from the generic driver and simplify the
prepare_write_buffer prototype:
int (*prepare_write_buffer)(struct usb_serial_port *port,
void *dest, size_t size);
The default implementation simply fills dest with data from port write
fifo but drivers can override it if they need to process the outgoing
data (e.g. add headers).
Turn ftdi_sio into a generic fifo-based driver, which lowers CPU usage
significantly for small writes while retaining maximum throughput.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Reimplement fifo-based writes in the generic driver using a multiple
pre-allocated urb scheme.
In contrast to multi-urb writes, no allocations (of urbs or buffers) are
made during run-time and there is less pressure on the host stack
queues as currently only two urbs are used (implementation is generic
and can handle more than two urbs as well, though).
Initial tests using ftdi_sio show that the implementation achieves the
same (maximum) throughput at high baudrates as multi-urb writes. The CPU
usage is much lower than for multi-urb writes for small write requests
and only slightly higher for large (e.g. 2k) requests (due to extra copy
via fifo?).
Also outperforms multi-urb writes for small write requests on an
embedded arm-9 system, where multi-urb writes are CPU-bound at high
baudrates (perf reveals that a lot of time is spent in the host stack
enqueue function -- could perhaps be a bug as well).
Keeping the original write_urb, buffer and flag for now as there are
other drivers depending on them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1377) simplifies the code in usb_sg_init(), without
changing its functionality. It also removes a couple of unused fields
from the usb_sg_request structure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Change the type of the URB's 'sg' pointer from a usb_sg_request to
a scatterlist. This allows drivers to submit scatter-gather lists
without using the usb_sg_wait() interface. It has the added benefit
of removing the typecasts that were added as part of patch as1368 (and
slightly decreasing the number of pointer dereferences).
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The stronger type-checking would have prevented a bug I had.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Converting a pipe number to a struct usb_host_endpoint pointer is a little
messy. Introduce a new convenience function to hide the mess.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Pipe Usage descriptor is needed for USB Attached SCSI
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Now that URB_NO_SETUP_DMA_MAP is no longer in use, this patch (as1376)
removes all references to it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1375) eliminates the usb_host_ss_ep_comp structure used
for storing a dynamically-allocated copy of the SuperSpeed endpoint
companion descriptor. The SuperSpeed descriptor is placed directly in
the usb_host_endpoint structure, alongside the standard endpoint
descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1374) cleans up a few loose ends in the
include/linux/usb/ch11.h header file and exports it to userspace.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Eric Lescouet <Eric.Lescouet@virtuallogix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds a sysfs entry (/sys/devices/platform/_UDC_/gadget/suspended) to
show the suspend state of an USB composite gadget.
Signed-off-by: Fabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Bulk endpoint streams were added in the USB 3.0 specification. Streams
allow a device driver to overload a bulk endpoint so that multiple
transfers can be queued at once.
The device then decides which transfer it wants to work on first, and can
queue part of a transfer before it switches to a new stream. All this
switching is invisible to the device driver, which just gets a completion
for the URB. Drivers that use streams must be able to handle URBs
completing in a different order than they were submitted to the endpoint.
This requires adding new API to set up xHCI data structures to support
multiple queues ("stream rings") per endpoint. Drivers will allocate a
number of stream IDs before enqueueing URBs to the bulk endpoints of the
device, and free the stream IDs in their disconnect function. See
Documentation/usb/bulk-streams.txt for details.
The new mass storage device class, USB Attached SCSI Protocol (UASP), uses
these streams API.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Bulk endpoint streams were added in the USB 3.0 specification. Streams
allow a device driver to overload a bulk endpoint so that multiple
transfers can be queued at once.
Add a new field, stream_id, to struct urb so that USB 3.0 drivers can
specify which stream they want the URB to be queued to.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Allow the xHCI drivers (and any new USB 3.0 drivers) to parse the
SuperSpeed endpoint companion descriptor to find the maximum number of
bulk endpoint streams the endpoint supports. This is used to calculate
the maximum total number of streams the driver can allocate.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1366) replaces the private routines
usb_enable_autosuspend() and usb_disable_autosuspend() with calls to
the standard pm_runtime_allow() and pm_runtime_forbid() functions in
the runtime PM framework. They do the same thing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1368) fixes a rather obscure bug in usbmon: When tracing
URBs sent by the scatter-gather library, it accesses the data buffers
while they are still mapped for DMA.
The solution is to move the mapping and unmapping out of the s-g
library and into the usual place in hcd.c. This requires the addition
of new URB flag bits to describe the kind of mapping needed, since we
have to call dma_map_sg() if the HCD supports native scatter-gather
operation and dma_map_page() if it doesn't. The nice thing about
having the new flags is that they simplify the testing for unmapping.
The patch removes the only caller of usb_buffer_[un]map_sg(), so those
functions are #if'ed out. A later patch will remove them entirely.
As a result of this change, urb->sg will be set in situations where
it wasn't set previously. Hence the xhci and whci drivers are
adjusted to test urb->num_sgs instead, which retains its original
meaning and is nonzero only when the HCD has to handle a scatterlist.
Finally, even when a submission error occurs we don't want to hand
URBs to usbmon before they are unmapped. The submission path is
rearranged so that map_urb_for_dma() is called only for non-root-hub
URBs and unmap_urb_for_dma() is called immediately after a submission
error. This simplifies the error handling.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Definitions for registers defined by ULPI specification v1.1.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
