| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.2-rc1
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
|
|
Folded into this merge commit is a build error fix: s/clk/core in
clk_change_rate due to the new struct clk_core
|
|
This flag is needed to fix the issue with wrong dividers being setup
by Common Clock Framework when using the new Exynos cpu clock support.
The issue happens because clk_core_set_rate_nolock() calls
clk_calc_new_rates(clk, rate) before both pre/post clock notifiers have
a chance to run. In case of Exynos cpu clock support pre/post clock
notifiers are registered for mout_apll clock which is a parent of armclk
cpu clock and dividers are modified in both pre and post clock notifier.
This results in wrong dividers values being later programmed by
clk_change_rate(top). To workaround the problem CLK_RECALC_NEW_RATES
flag is added and it is set for mout_apll clock later so the correct
divider values are re-calculated after both pre and post clock notifiers
had run.
For example when using "performance" governor on Exynos4210 Origen board
the cpufreq-dt driver requests to change the frequency from 1000MHz to
1200MHz and after the change state of the relevant clocks is following:
Without use of CLK_GET_RATE_NOCACHE flag:
fout_apll rate: 1200000000
fout_apll_div_2 rate: 600000000
mout_clkout_cpu rate: 600000000
div_clkout_cpu rate: 600000000
clkout_cpu rate: 600000000
mout_apll rate: 1200000000
armclk rate: 1200000000
mout_hpm rate: 1200000000
div_copy rate: 300000000
div_hpm rate: 300000000
mout_core rate: 1200000000
div_core rate: 1200000000
div_core2 rate: 1200000000
arm_clk_div_2 rate: 600000000
div_corem0 rate: 300000000
div_corem1 rate: 150000000
div_periph rate: 300000000
div_atb rate: 300000000
div_pclk_dbg rate: 150000000
sclk_apll rate: 1200000000
sclk_apll_div_2 rate: 600000000
With use of CLK_GET_RATE_NOCACHE flag:
fout_apll rate: 1200000000
fout_apll_div_2 rate: 600000000
mout_clkout_cpu rate: 600000000
div_clkout_cpu rate: 600000000
clkout_cpu rate: 600000000
mout_apll rate: 1200000000
armclk rate: 1200000000
mout_hpm rate: 1200000000
div_copy rate: 200000000
div_hpm rate: 200000000
mout_core rate: 1200000000
div_core rate: 1200000000
div_core2 rate: 1200000000
arm_clk_div_2 rate: 600000000
div_corem0 rate: 300000000
div_corem1 rate: 150000000
div_periph rate: 300000000
div_atb rate: 240000000
div_pclk_dbg rate: 120000000
sclk_apll rate: 150000000
sclk_apll_div_2 rate: 75000000
Without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board.
This issue was probably meant to be workarounded by use of
CLK_GET_RATE_NOCACHE and CLK_DIVIDER_READ_ONLY clock flags in
the original Exynos cpu clock patchset (in "[PATCH v12 6/6] clk:
samsung: remove unused clock aliases and update clock flags" patch)
but usage of these flags is not sufficient to fix the issue observed.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
Add driver for NXP LPC18xx/43xx Clock Control Unit (CCU). The CCU
provides fine grained gating of most clocks present in the SoC.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
Add driver for NXP LPC18xx/43xx Clock Generation Unit (CGU). The CGU
contains several clock generators and output stages that route the
clocks either directly to peripherals or to a Clock Control Unit
(CCU).
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
The Broadcom Cygnus SoC is architected under the iProc architecture. It
has the following PLLs: ARMPLL, GENPLL, LCPLL0, MIPIPLL, all dervied
from an onboard crystal. Cygnus also has various ASIU clocks that are
derived directly from the onboard crystal.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
|
|
Currently it is not made explicit why clk_fixed_set_rate() can ignore
its arguments and unconditionally return success. Add a comment
to explain this.
We also mark the clk_ops table const since it should never be
modified at runtime.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two fixes for the driver core that resolve some reported
issues.
One is a regression from 4.0, the other a fixes a reported oops that
has been there since 3.19.
Both have been in linux-next for a while with no problems"
* tag 'driver-core-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base: cacheinfo: handle absence of caches
drivers: of/base: move of_init to driver_init
|
|
Sprinkled all through the platform clock drivers are code like this to
fill the clock parent array:
for (i = 0; i < num_parents; ++i)
parent_names[i] = of_clk_get_parent_name(np, i);
The of_clk_parent_fill() will do the same as the code above, and while
at it, return the number of parents as well since the logic of the
function is to the walk the clock node to look for the parent.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
[sboyd@codeaurora.org: Fixed kernel-doc]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
* clk-meson8b:
clk: meson8b: Add support for Meson8b clocks
clk: meson: Document bindings for Meson8b clock controller
clk: meson: Add support for Meson clock controller
|
|
This patchset adds the infrastructure for registering and managing the
core clocks found on Amlogic MesonX SoCs. In particular:
- PLLs
- CPU clock
- Fixed rate clocks, fixed factor clocks, ...
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"The biggest chunk of the changes are two regression fixes: a HT
workaround fix and an event-group scheduling fix. It's been verified
with 5 days of fuzzer testing.
Other fixes:
- eBPF fix
- a BIOS breakage detection fix
- PMU driver fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/pt: Fix a refactoring bug
perf/x86: Tweak broken BIOS rules during check_hw_exists()
perf/x86/intel/pt: Untangle pt_buffer_reset_markers()
perf: Disallow sparse AUX allocations for non-SG PMUs in overwrite mode
perf/x86: Improve HT workaround GP counter constraint
perf/x86: Fix event/group validation
perf: Fix race in BPF program unregister
|
|
Timer has external fast clock, and it is a mux clock.
Add the timer clock type for timer driver.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
USB will drive clock from USB_PLL.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Pull block layer fixes from Jens Axboe:
"Sending this off now, as I'm not aware of other current bugs, nor do I
expect further fixes before 4.1 final. This contains two fixes:
- a fix for a bdi unregister warning that gets spewed on md, due to a
regression introduced earlier in this cycle. From Neil Brown.
- a fix for a compile warning for NVMe on 32-bit platforms, also a
regression introduced in this cycle. From Arnd Bergmann"
* 'for-linus' of git://git.kernel.dk/linux-block:
NVMe: fix type warning on 32-bit
block: discard bdi_unregister() in favour of bdi_destroy()
|
|
Conflicts:
drivers/clk/Kconfig
|
|
Add the header file "hi6220-clock.h" used by both
hi6220 clock driver and hi6220 device tree file.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
|
|
Pull networking fixes from David Miller:
1) Various VTI tunnel (mark handling, PMTU) bug fixes from Alexander
Duyck and Steffen Klassert.
2) Revert ethtool PHY query change, it wasn't correct. The PHY address
selected by the driver running the PHY to MAC connection decides
what PHY address GET ethtool operations return information from.
3) Fix handling of sequence number bits for encryption IV generation in
ESP driver, from Herbert Xu.
4) UDP can return -EAGAIN when we hit a bad checksum on receive, even
when there are other packets in the receive queue which is wrong.
Just respect the error returned from the generic socket recv
datagram helper. From Eric Dumazet.
5) Fix BNA driver firmware loading on big-endian systems, from Ivan
Vecera.
6) Fix regression in that we were inheriting the congestion control of
the listening socket for new connections, the intended behavior
always was to use the default in this case. From Neal Cardwell.
7) Fix NULL deref in brcmfmac driver, from Arend van Spriel.
8) OTP parsing fix in iwlwifi from Liad Kaufman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
vti6: Add pmtu handling to vti6_xmit.
Revert "net: core: 'ethtool' issue with querying phy settings"
bnx2x: Move statistics implementation into semaphores
xen: netback: read hotplug script once at start of day.
xen: netback: fix printf format string warning
Revert "netfilter: ensure number of counters is >0 in do_replace()"
net: dsa: Properly propagate errors from dsa_switch_setup_one
tcp: fix child sockets to use system default congestion control if not set
udp: fix behavior of wrong checksums
sfc: free multiple Rx buffers when required
bna: fix soft lock-up during firmware initialization failure
bna: remove unreasonable iocpf timer start
bna: fix firmware loading on big-endian machines
bridge: fix br_multicast_query_expired() bug
via-rhine: Resigning as maintainer
brcmfmac: avoid null pointer access when brcmf_msgbuf_get_pktid() fails
mac80211: Fix mac80211.h docbook comments
iwlwifi: nvm: fix otp parsing in 8000 hw family
iwlwifi: pcie: fix tracking of cmd_in_flight
ip_vti/ip6_vti: Preserve skb->mark after rcv_cb call
...
|
|
Fixes userspace compilation error:
error: unknown type name ‘__virtio16’
__virtio16 tag;
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Linux 3.17 and earlier are explicitly engineered so that if the app
doesn't specifically request a CC module on a listener before the SYN
arrives, then the child gets the system default CC when the connection
is established. See tcp_init_congestion_control() in 3.17 or earlier,
which says "if no choice made yet assign the current value set as
default". The change ("net: tcp: assign tcp cong_ops when tcp sk is
created") altered these semantics, so that children got their parent
listener's congestion control even if the system default had changed
after the listener was created.
This commit returns to those original semantics from 3.17 and earlier,
since they are the original semantics from 2007 in 4d4d3d1e8 ("[TCP]:
Congestion control initialization."), and some Linux congestion
control workflows depend on that.
In summary, if a listener socket specifically sets TCP_CONGESTION to
"x", or the route locks the CC module to "x", then the child gets
"x". Otherwise the child gets current system default from
net.ipv4.tcp_congestion_control. That's the behavior in 3.17 and
earlier, and this commit restores that.
Fixes: 55d8694fa82c ("net: tcp: assign tcp cong_ops when tcp sk is created")
Cc: Florian Westphal <fw@strlen.de>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes, with the exception of the following that
address fall-out from recent v4.1-rc1 changes:
- regression fix related to the big fabric API registration changes
and configfs_depend_item() usage, that required cherry-picking one
of HCH's patches from for-next to address the issue for v4.1 code.
- remaining TCM-USER -v2 related changes to enforce full CDB
passthrough from Andy + Ilias.
Also included is a target_core_pscsi driver fix from Andy that
addresses a long standing issue with a Scsi_Host reference being
leaked on PSCSI device shutdown"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iser-target: Fix error path in isert_create_pi_ctx()
target: Use a PASSTHROUGH flag instead of transport_types
target: Move passthrough CDB parsing into a common function
target/user: Only support full command pass-through
target/user: Update example code for new ABI requirements
target/pscsi: Don't leak scsi_host if hba is VIRTUAL_HOST
target: Fix se_tpg_tfo->tf_subsys regression + remove tf_subsystem
target: Drop signal_pending checks after interruptible lock acquire
target: Add missing parentheses
target: Fix bidi command handling
target/user: Disallow full passthrough (pass_level=0)
ISCSI: fix minor memory leak
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
This just has a single docbook build fix. In my confusion
I'd already sent the same fix for -next, but Ben Hutchings
noted it's necessary in 4.1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems like we only care if a transport is passthrough or not. Convert
transport_type to a flags field and replace TRANSPORT_PLUGIN_* with a
flag, TRANSPORT_FLAG_PASSTHROUGH.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Aside from whether they handle BIDI ops or not, parsing of the CDB by
kernel and user SCSI passthrough modules should be identical. Move this
into a new passthrough_parse_cdb() and call it from tcm-pscsi and tcm-user.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
There is just one configfs subsystem in the target code, so we might as
well add two helpers to reference / unreference it from the core code
instead of passing pointers to it around.
This fixes a regression introduced for v4.1-rc1 with commit 9ac8928e6,
where configfs_depend_item() callers using se_tpg_tfo->tf_subsys would
fail, because the assignment from the original target_core_subsystem[]
is no longer happening at target_register_template() time.
(Fix target_core_exit_configfs pointer dereference - Sagi)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This is a little larger than I'd like late in the release cycle, but
all the fixes are for regressions introduced in the 4.1-rc1 merge, or
are needed back in -stable kernels fairly quickly as they are
filesystem corruption or userspace visible correctness issues.
Changes in this update:
- regression fix for new rename whiteout code
- regression fixes for new superblock generic per-cpu counter code
- fix for incorrect error return sign introduced in 3.17
- metadata corruption fixes that need to go back to -stable kernels"
* tag 'xfs-for-linus-4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: fix broken i_nlink accounting for whiteout tmpfile inode
xfs: xfs_iozero can return positive errno
xfs: xfs_attr_inactive leaves inconsistent attr fork state behind
xfs: extent size hints can round up extents past MAXEXTLEN
xfs: inode and free block counters need to use __percpu_counter_compare
percpu_counter: batch size aware __percpu_counter_compare()
xfs: use percpu_counter_read_positive for mp->m_icount
|
|
Merge misc fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
scripts/gdb: fix lx-lsmod refcnt
omfs: fix potential integer overflow in allocator
omfs: fix sign confusion for bitmap loop counter
omfs: set error return when d_make_root() fails
fs, omfs: add NULL terminator in the end up the token list
MAINTAINERS: update CAPABILITIES pattern
fs/binfmt_elf.c:load_elf_binary(): return -EINVAL on zero-length mappings
tracing/mm: don't trace mm_page_pcpu_drain on offline cpus
tracing/mm: don't trace mm_page_free on offline cpus
tracing/mm: don't trace kmem_cache_free on offline cpus
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull fixes for cpumask and modules from Rusty Russell:
"** NOW WITH TESTING! **
Two fixes which got lost in my recent distraction. One is a weird
cpumask function which needed to be rewritten, the other is a module
bug which is cc:stable"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
cpumask_set_cpu_local_first => cpumask_local_spread, lament
module: Call module notifier on failure after complete_formation()
|
|
Since tracepoints use RCU for protection, they must not be called on
offline cpus. trace_mm_page_pcpu_drain can be called on an offline cpu
in this scenario caught by LOCKDEP:
===============================
[ INFO: suspicious RCU usage. ]
4.1.0-rc1+ #9 Not tainted
-------------------------------
include/trace/events/kmem.h:265 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from offline CPU!
rcu_scheduler_active = 1, debug_locks = 1
1 lock held by swapper/5/0:
#0: (&(&zone->lock)->rlock){..-...}, at: [<c0000000002073b0>] .free_pcppages_bulk+0x70/0x920
stack backtrace:
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 4.1.0-rc1+ #9
Call Trace:
.dump_stack+0x98/0xd4 (unreliable)
.lockdep_rcu_suspicious+0x108/0x170
.free_pcppages_bulk+0x60c/0x920
.free_hot_cold_page+0x208/0x280
.destroy_context+0x90/0xd0
.__mmdrop+0x58/0x160
.idle_task_exit+0xf0/0x100
.pnv_smp_cpu_kill_self+0x58/0x2c0
.cpu_die+0x34/0x50
.arch_cpu_idle_dead+0x20/0x40
.cpu_startup_entry+0x708/0x7a0
.start_secondary+0x36c/0x3a0
start_secondary_prolog+0x10/0x14
Fix this by converting mm_page_pcpu_drain trace point into
TRACE_EVENT_CONDITION where condition is cpu_online(smp_processor_id())
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since tracepoints use RCU for protection, they must not be called on
offline cpus. trace_mm_page_free can be called on an offline cpu in this
scenario caught by LOCKDEP:
===============================
[ INFO: suspicious RCU usage. ]
4.1.0-rc1+ #9 Not tainted
-------------------------------
include/trace/events/kmem.h:170 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from offline CPU!
rcu_scheduler_active = 1, debug_locks = 1
no locks held by swapper/1/0.
stack backtrace:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.1.0-rc1+ #9
Call Trace:
.dump_stack+0x98/0xd4 (unreliable)
.lockdep_rcu_suspicious+0x108/0x170
.free_pages_prepare+0x494/0x680
.free_hot_cold_page+0x50/0x280
.destroy_context+0x90/0xd0
.__mmdrop+0x58/0x160
.idle_task_exit+0xf0/0x100
.pnv_smp_cpu_kill_self+0x58/0x2c0
.cpu_die+0x34/0x50
.arch_cpu_idle_dead+0x20/0x40
.cpu_startup_entry+0x708/0x7a0
.start_secondary+0x36c/0x3a0
start_secondary_prolog+0x10/0x14
Fix this by converting mm_page_free trace point into TRACE_EVENT_CONDITION
where condition is cpu_online(smp_processor_id())
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since tracepoints use RCU for protection, they must not be called on
offline cpus. trace_kmem_cache_free can be called on an offline cpu in
this scenario caught by LOCKDEP:
===============================
[ INFO: suspicious RCU usage. ]
4.1.0-rc1+ #9 Not tainted
-------------------------------
include/trace/events/kmem.h:148 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from offline CPU!
rcu_scheduler_active = 1, debug_locks = 1
no locks held by swapper/1/0.
stack backtrace:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.1.0-rc1+ #9
Call Trace:
.dump_stack+0x98/0xd4 (unreliable)
.lockdep_rcu_suspicious+0x108/0x170
.kmem_cache_free+0x344/0x4b0
.__mmdrop+0x4c/0x160
.idle_task_exit+0xf0/0x100
.pnv_smp_cpu_kill_self+0x58/0x2c0
.cpu_die+0x34/0x50
.arch_cpu_idle_dead+0x20/0x40
.cpu_startup_entry+0x708/0x7a0
.start_secondary+0x36c/0x3a0
start_secondary_prolog+0x10/0x14
Fix this by converting kmem_cache_free trace point into
TRACE_EVENT_CONDITION where condition is cpu_online(smp_processor_id())
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
XFS uses non-stanard batch sizes for avoiding frequent global
counter updates on it's allocated inode counters, as they increment
or decrement in batches of 64 inodes. Hence the standard percpu
counter batch of 32 means that the counter is effectively a global
counter. Currently Xfs uses a batch size of 128 so that it doesn't
take the global lock on every single modification.
However, Xfs also needs to compare accurately against zero, which
means we need to use percpu_counter_compare(), and that has a
hard-coded batch size of 32, and hence will spuriously fail to
detect when it is supposed to use precise comparisons and hence
the accounting goes wrong.
Add __percpu_counter_compare() to take a custom batch size so we can
use it sanely in XFS and factor percpu_counter_compare() to use it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
bdi_unregister() now contains very little functionality.
It contains a "WARN_ON" if bdi->dev is NULL. This warning is of no
real consequence as bdi->dev isn't needed by anything else in the function,
and it triggers if
blk_cleanup_queue() -> bdi_destroy()
is called before bdi_unregister, which happens since
Commit: 6cd18e711dd8 ("block: destroy bdi before blockdev is unregistered.")
So this isn't wanted.
It also calls bdi_set_min_ratio(). This needs to be called after
writes through the bdi have all been flushed, and before the bdi is destroyed.
Calling it early is better than calling it late as it frees up a global
resource.
Calling it immediately after bdi_wb_shutdown() in bdi_destroy()
perfectly fits these requirements.
So bdi_unregister() can be discarded with the important content moved to
bdi_destroy(), as can the
writeback_bdi_unregister
event which is already not used.
Reported-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org (v4.0)
Fixes: c4db59d31e39 ("fs: don't reassign dirty inodes to default_backing_dev_info")
Fixes: 6cd18e711dd8 ("block: destroy bdi before blockdev is unregistered.")
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
A couple of enums in mac80211.h became structures recently, but the
comments didn't follow suit, leading to errors like:
Error(.//include/net/mac80211.h:367): Cannot parse enum!
Documentation/DocBook/Makefile:93: recipe for target 'Documentation/DocBook/80211.xml' failed
make[1]: *** [Documentation/DocBook/80211.xml] Error 1
Makefile:1361: recipe for target 'mandocs' failed
make: *** [mandocs] Error 2
Fix the comments comments accordingly. Added a couple of other small
comment fixes while I was there to silence other recently-added docbook
warnings.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
da91309e0a7e (cpumask: Utility function to set n'th cpu...) created a
genuinely weird function. I never saw it before, it went through DaveM.
(He only does this to make us other maintainers feel better about our own
mistakes.)
cpumask_set_cpu_local_first's purpose is say "I need to spread things
across N online cpus, choose the ones on this numa node first"; you call
it in a loop.
It can fail. One of the two callers ignores this, the other aborts and
fails the device open.
It can fail in two ways: allocating the off-stack cpumask, or through a
convoluted codepath which AFAICT can only occur if cpu_online_mask
changes. Which shouldn't happen, because if cpu_online_mask can change
while you call this, it could return a now-offline cpu anyway.
It contains a nonsensical test "!cpumask_of_node(numa_node)". This was
drawn to my attention by Geert, who said this causes a warning on Sparc.
It sets a single bit in a cpumask instead of returning a cpu number,
because that's what the callers want.
It could be made more efficient by passing the previous cpu rather than
an index, but that would be more invasive to the callers.
Fixes: da91309e0a7e8966d916a74cce42ed170fde06bf
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (then rebased)
Tested-by: Amir Vadai <amirv@mellanox.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Don't use MMIO on certain iwlwifi devices otherwise we get a
firmware crash.
2) Don't corrupt the GRO lists of mac80211 contexts by doing sends via
timer interrupt, from Johannes Berg.
3) SKB tailroom is miscalculated in AP_VLAN crypto code, from Michal
Kazior.
4) Fix fw_status memory leak in iwlwifi, from Haim Dreyfuss.
5) Fix use after free in iwl_mvm_d0i3_enable_tx(), from Eliad Peller.
6) JIT'ing of large BPF programs is broken on x86, from Alexei
Starovoitov.
7) EMAC driver ethtool register dump size is miscalculated, from Ivan
Mikhaylov.
8) Fix PHY initial link mode when autonegotiation is disabled in
amd-xgbe, from Tom Lendacky.
9) Fix NULL deref on SOCK_DEAD socket in AF_UNIX and CAIF protocols,
from Mark Salyzyn.
10) credit_bytes not initialized properly in xen-netback, from Ross
Lagerwall.
11) Fallback from MSI-X to INTx interrupts not handled properly in mlx4
driver, fix from Benjamin Poirier.
12) Perform ->attach() after binding dev->qdisc in packet scheduler,
otherwise we can crash. From Cong WANG.
13) Don't clobber data in sctp_v4_map_v6(). From Jason Gunthorpe.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
sctp: Fix mangled IPv4 addresses on a IPv6 listening socket
net_sched: invoke ->attach() after setting dev->qdisc
xen-netfront: properly destroy queues when removing device
mlx4_core: Fix fallback from MSI-X to INTx
xen/netback: Properly initialize credit_bytes
net: netxen: correct sysfs bin attribute return code
tools: bpf_jit_disasm: fix segfault on disabled debugging log output
unix/caif: sk_socket can disappear when state is unlocked
amd-xgbe-phy: Fix initial mode when autoneg is disabled
net: dp83640: fix improper double spin locking.
net: dp83640: reinforce locking rules.
net: dp83640: fix broken calibration routine.
net: stmmac: create one debugfs dir per net-device
net/ibm/emac: fix size of emac dump memory areas
x86: bpf_jit: fix compilation of large bpf programs
net: phy: bcm7xxx: Fix 7425 PHY ID and flags
iwlwifi: mvm: avoid use-after-free on iwl_mvm_d0i3_enable_tx()
iwlwifi: mvm: clean net-detect info if device was reset during suspend
iwlwifi: mvm: take the UCODE_DOWN reference when resuming
iwlwifi: mvm: BT Coex - duplicate the command if sent ASYNC
...
|
|
sctp_v4_map_v6 was subtly writing and reading from members
of a union in a way the clobbered data it needed to read before
it read it.
Zeroing the v6 flowinfo overwrites the v4 sin_addr with 0, meaning
that every place that calls sctp_v4_map_v6 gets ::ffff:0.0.0.0 as the
result.
Reorder things to guarantee correct behaviour no matter what the
union layout is.
This impacts user space clients that open an IPv6 SCTP socket and
receive IPv4 connections. Prior to 299ee user space would see a
sockaddr with AF_INET and a correct address, after 299ee the sockaddr
is AF_INET6, but the address is wrong.
Fixes: 299ee123e198 (sctp: Fixup v4mapped behaviour to comply with Sock API)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 43b4578071c0 ("perf/x86: Reduce stack usage of
x86_schedule_events()") violated the rule that 'fake' scheduling; as
used for event/group validation; should not change the event state.
This went mostly un-noticed because repeated calls of
x86_pmu::get_event_constraints() would give the same result. And
x86_pmu::put_event_constraints() would mostly not do anything.
Commit e979121b1b15 ("perf/x86/intel: Implement cross-HT corruption
bug workaround") made the situation much worse by actually setting the
event->hw.constraint value to NULL, so when validation and actual
scheduling interact we get NULL ptr derefs.
Fix it by removing the constraint pointer from the event and move it
back to an array, this time in cpuc instead of on the stack.
validate_group()
x86_schedule_events()
event->hw.constraint = c; # store
<context switch>
perf_task_event_sched_in()
...
x86_schedule_events();
event->hw.constraint = c2; # store
...
put_event_constraints(event); # assume failure to schedule
intel_put_event_constraints()
event->hw.constraint = NULL;
<context switch end>
c = event->hw.constraint; # read -> NULL
if (!test_bit(hwc->idx, c->idxmsk)) # <- *BOOM* NULL deref
This in particular is possible when the event in question is a
cpu-wide event and group-leader, where the validate_group() tries to
add an event to the group.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Hunter <ahh@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maria Dimakopoulou <maria.n.dimakopoulou@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 43b4578071c0 ("perf/x86: Reduce stack usage of x86_schedule_events()")
Fixes: e979121b1b15 ("perf/x86/intel: Implement cross-HT corruption bug workaround")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit 5590f3196b29 ("drivers/core/of: Add symlink to device-tree from
devices with an OF node") adds the symlink `of_node` for each device
pointing to it's device tree node while creating/initialising it.
However the devicetree sysfs is created and setup in of_init which is
executed at core_initcall level. For all the devices created before
of_init, the following error is thrown:
"Error -2(-ENOENT) creating of_node link"
Like many other components in driver model, initialize the sysfs support
for OF/devicetree from driver_init so that it's ready before any devices
are created.
Fixes: 5590f3196b29 ("drivers/core/of: Add symlink to device-tree from
devices with an OF node")
Suggested-by: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Robert Schwebel <r.schwebel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While adding support for 7425 PHY in the 7xxx PHY driver, the ID that
was used was actually coming from an external PHY: a BCM5461x. Fix this
by using the proper ID for the internal 7425 PHY and set the
PHY_IS_INTERNAL flag, otherwise consumers of this PHY driver would not
be able to properly identify it as such.
Fixes: d068b02cfdfc2 ("net: phy: add BCM7425 and BCM7429 PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"One more fix from the timer departement:
- Handle division of negative nanosecond values proper on 32bit.
A recent cleanup wrecked the sign handling of the dividend and
dropped the check for negative divisors"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Fix ktime_divns to do signed division
|
|
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
|
|
Pull block fixes from Jens Axboe:
"Three small fixes that have been picked up the last few weeks.
Specifically:
- Fix a memory corruption issue in NVMe with malignant user
constructed request. From Christoph.
- Kill (now) unused blk_queue_bio(), dm was changed to not need this
anymore. From Mike Snitzer.
- Always use blk_schedule_flush_plug() from the io_schedule() path
when flushing a plug, fixing a !TASK_RUNNING warning with md. From
Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
sched: always use blk_schedule_flush_plug in io_schedule_out
nvme: fix kernel memory corruption with short INQUIRY buffers
block: remove export for blk_queue_bio
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contain Netfilter fixes for your net tree, they are:
1) Fix a race in nfnetlink_log and nfnetlink_queue that can lead to a crash.
This problem is due to wrong order in the per-net registration and netlink
socket events. Patch from Francesco Ruggeri.
2) Make sure that counters that userspace pass us are higher than 0 in all the
x_tables frontends. Discovered via Trinity, patch from Dave Jones.
3) Revert a patch for br_netfilter to rely on the conntrack status bits. This
breaks stateless IPv6 NAT transformations. Patch from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Taking socket spinlock in tcp_get_info() can deadlock, as
inet_diag_dump_icsk() holds the &hashinfo->ehash_locks[i],
while packet processing can use the reverse locking order.
We could avoid this locking for TCP_LISTEN states, but lockdep would
certainly get confused as all TCP sockets share same lockdep classes.
[ 523.722504] ======================================================
[ 523.728706] [ INFO: possible circular locking dependency detected ]
[ 523.734990] 4.1.0-dbg-DEV #1676 Not tainted
[ 523.739202] -------------------------------------------------------
[ 523.745474] ss/18032 is trying to acquire lock:
[ 523.750002] (slock-AF_INET){+.-...}, at: [<ffffffff81669d44>] tcp_get_info+0x2c4/0x360
[ 523.758129]
[ 523.758129] but task is already holding lock:
[ 523.763968] (&(&hashinfo->ehash_locks[i])->rlock){+.-...}, at: [<ffffffff816bcb75>] inet_diag_dump_icsk+0x1d5/0x6c0
[ 523.774661]
[ 523.774661] which lock already depends on the new lock.
[ 523.774661]
[ 523.782850]
[ 523.782850] the existing dependency chain (in reverse order) is:
[ 523.790326]
-> #1 (&(&hashinfo->ehash_locks[i])->rlock){+.-...}:
[ 523.796599] [<ffffffff811126bb>] lock_acquire+0xbb/0x270
[ 523.802565] [<ffffffff816f5868>] _raw_spin_lock+0x38/0x50
[ 523.808628] [<ffffffff81665af8>] __inet_hash_nolisten+0x78/0x110
[ 523.815273] [<ffffffff816819db>] tcp_v4_syn_recv_sock+0x24b/0x350
[ 523.822067] [<ffffffff81684d41>] tcp_check_req+0x3c1/0x500
[ 523.828199] [<ffffffff81682d09>] tcp_v4_do_rcv+0x239/0x3d0
[ 523.834331] [<ffffffff816842fe>] tcp_v4_rcv+0xa8e/0xc10
[ 523.840202] [<ffffffff81658fa3>] ip_local_deliver_finish+0x133/0x3e0
[ 523.847214] [<ffffffff81659a9a>] ip_local_deliver+0xaa/0xc0
[ 523.853440] [<ffffffff816593b8>] ip_rcv_finish+0x168/0x5c0
[ 523.859624] [<ffffffff81659db7>] ip_rcv+0x307/0x420
Lets use u64_sync infrastructure instead. As a bonus, 64bit
arches get optimized, as these are nop for them.
Fixes: 0df48c26d841 ("tcp: add tcpi_bytes_acked to tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull two xen bugfixes from David Vrabel:
- fix ARM build regression.
- fix VIRQ_CONSOLE related oops.
* tag 'for-linus-4.1b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: don't bind non-percpu VIRQs with percpu chip
xen/arm: Define xen_arch_suspend()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
"Bugfixes for HID subsystem that should go in 4.1. Important
highlights:
- the patch that extended support for HID++ protocol for TK820
touchpad turns out to be causing regressions due to firmware
issues; patch reverting back to basic support from Benjamin
Tissoires
- Wacom driver can oops for devices that report non-touch data on
touch interfaces. Fix from Ping Cheng
- gpiolib is not mandatory for i2c-hid, so the driver shouldn't fail
if gpiolib is not enabled. Fix from Mika Westerberg"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: fix an Oops caused by wacom_wac_finger_count_touches
HID: usbhid: Add HID_QUIRK_NOGET for Aten DVI KVM switch
HID: hid-sensor-hub: Fix debug lock warning
Revert "HID: logitech-hidpp: support combo keyboard touchpad TK820"
HID: i2c-hid: Do not fail probing if gpiolib is not enabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"The first set of clk fixes for 4.1 are all driver bugs, with the
exception of a single locking fix in the core code.
All driver fixes are for code that was merged recently. The Samsung
stuff is mostly fixes around suspend/resume, the Qualcomm fixes are
for invalid hardware configuration data and the Silicon Labs patches
are fixes following their move away from platform_data to Device Tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: si5351: Do not pass struct clk in platform_data
clk: si5351: Mention clock-names in the binding documentation
clk: add missing lock when call clk_core_enable in clk_set_parent
clk: exynos5420: Restore GATE_BUS_TOP on suspend
clk: qcom: Fix MSM8916 gfx3d_clk_src configuration
clk: qcom: Fix MSM8916 venus divider value
clk: exynos5433: Fix wrong PMS value of exynos5433_pll_rates
clk: exynos5433: Fix wrong parent clock of sclk_apollo clock
clk: exynos5433: Fix CLK_PCLK_MONOTONIC_CNT clk register assignment
clk: exynos5433: Fix wrong offset of PCLK_MSCL_SECURE_SMMU_JPEG
clk: Use CONFIG_ARCH_EXYNOS instead of CONFIG_ARCH_EXYNOS5433
|
|
This reverts commit c055d5b03bb4cb69d349d787c9787c0383abd8b2.
There are two issues:
'dnat_took_place' made me think that this is related to
-j DNAT/MASQUERADE.
But thats only one part of the story. This is also relevant for SNAT
when we undo snat translation in reverse/reply direction.
Furthermore, I originally wanted to do this mainly to avoid
storing ipv6 addresses once we make DNAT/REDIRECT work
for ipv6 on bridges.
However, I forgot about SNPT/DNPT which is stateless.
So we can't escape storing address for ipv6 anyway. Might as
well do it for ipv4 too.
Reported-and-tested-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
