| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
|
|
Add all R-Car H3 Clock Pulse Generator Core Clock Outputs, as listed in
Table 8.2a ("List of Clocks [R-Car H3]") of the R-Car Gen3 datasheet
(rev. 0.5E).
Note that internal CPG clocks (S0, S1, S2, S3, SDSRC, SSPSRC, and
RPCSRC) are not included, as they're used as internal clock sources
only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Magnus Damm <damm+renesas@opensource.se>
|
|
On Renesas ARM SoCs (SH/R-Mobile, R-Car, RZ), the CPG (Clock Pulse
Generator) and MSSR (Module Standby and Software Reset) blocks are
intimately connected, and share the same register block.
Hence it makes sense to describe these two blocks using a
single device node in DT, instead of using a hierarchical structure with
multiple nodes, using a mix of generic and SoC-specific bindings.
These new DT bindings are intended to replace the existing DT bindings
for CPG core clocks ("renesas,*-cpg-clocks", "renesas,cpg-div6-clock")
and module clocks ("renesas,*-mstp-clocks"), at least for new SoCs.
This will make it easier to add module reset support later, which is
currently not implemented, and difficult to achieve using the existing
bindings due to the intertwined register layout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Magnus Damm <damm+renesas@opensource.se>
|
|
When calling __clk_get_name() on a const clock:
warning: passing argument 1 of '__clk_get_name' discards 'const' qualifier from pointer target type
include/linux/clk-provider.h:613:13: note: expected 'struct clk *' but argument is of type 'const struct clk *'
__clk_get_name() does not modify the passed clock, hence make it const.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-next
Pull i.MX updates from Shawn Guo:
"The i.MX clock updates for 4.4:
- A couple of fixes on i.MX31 and i.MX35 clock initialization functions
which makes mxc_timer_init() currently be called twice for DT boot.
- Increase i.MX6UL AXI bus clock rate to 264MHz which is the optimal
design target.
- Add a few missing clocks, ADC clock for i.MX7D, OCOTP clock for
Vybrid, and SPDIF_GCLK for i.MX6.
- A series from Lucas to fix early debug UART clock setup. This is
currently a one-off fix for i.MX platform, and can be extended to
become a generic solution later."
* tag 'imx-clk-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx6: Add SPDIF_GCLK clock in clock tree
clk: imx7d: add ADC root clock
clk: imx31: Do not call mxc_timer_init twice when booting with DT
clk: imx7d: retain early UART clocks during kernel init
clk: imx6: retain early UART clocks during kernel init
clk: imx5: retain early UART clocks during kernel init
clk: imx35: retain early UART clocks during kernel init
clk: imx31: retain early UART clocks during kernel init
clk: imx27: retain early UART clocks during kernel init
clk: imx25: retain early UART clocks during kernel init
clk: imx: add common logic to detect early UART usage
clk: imx35: Do not call mxc_timer_init twice when booting with DT
clk: clk-vf610: Add clock for Vybrid OCOTP controller
clk: imx: increase AXI clock rate to 264MHz for i.MX6UL
|
|
* clk-bcm2835:
clk: bcm2835: Add support for programming the audio domain clocks
clk: bcm2835: Add binding docs for the new platform clock driver.
clk: bcm2835: Move under bcm/ with other Broadcom SoC clk drivers.
|
|
Correct SPDIF clock setting issue in clock tree, the SPDIF_GCLK is also
one clock of SPDIF, which is missed before.
We found an issue that imx can't enter low power mode with spdif
if IMX6x_CLK_SPDIF is used as the core clock of spdif. Because
spdif driver will register IMX6x_CLK_SPDIF clock to regmap, regmap will do
clk_prepare in init function, then IMX6x_CLK_SPDIF clock is prepared in probe,
so its parent clock (PLL clock) is prepared, the prepare operation of
PLL clock is to enable the clock. But I.MX needs all PLL clock is disabled,
then it can enter low power mode.
So we can't use IMX6x_CLK_SPDIF as the core clock of spdif, the correct spdif
core clock is SPDIF_GCLK, which share same gate bit with IMX6x_CLK_SPDIF clock.
SPDIF_GCLK's parent clock is ipg clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add ADC root clock support in imx7d clock tree.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
clk-next
Pull mediatek clock support and fixes from James Liao:
"This is a collection of new Mediatek clocks support and fixes.
These patches come from Joe and me, including clock support for
subsystems, GPT and some minor fixes."
* 'v4.3-rc3-clk' of https://github.com/jamesjjliao/linux:
clk: mediatek: Add USB clock support in MT8173 APMIXEDSYS
clk: mediatek: Add subsystem clocks of MT8173
dt-bindings: ARM: Mediatek: Document devicetree bindings for clock controllers
clk: mediatek: Fix rate and dependency of MT8173 clocks
clk: mediatek: Add fixed clocks support for Mediatek SoC.
clk: mediatek: Add __initdata and __init for data and functions
clk: mediatek: Remove unused code from MT8173.
clk: mediatek: Removed unused dpi_ck clock from MT8173
clk: mediatek: add 13mhz clock for MT8173
|
|
Pull updates from Sylwester Nawrocki:
"Fixes, improvements and addition of some missing features
of the exynos7 clock controller driver."
* tag 'clk-samsung-4.4' of git://linuxtv.org/snawrocki/samsung:
clk: samsung: exynos7: Add required clock tree for UFS
clk: samsung: exynos7: Add missing fixed_clks to cmu_info
clk: samsung: exynos7: Correct CMU_FSYS1 clocks names
clk: samsung: exynos7: Correct CMU_FSYS0 clocks names
clk: samsung: exynos7: Correct CMU_PERIS clocks names
clk: samsung: exynos7: Correct CMU_PERIC1 clocks names
clk: samsung: exynos7: Correct CMU_PERIC0 clocks names
clk: samsung: exynos7: Correct CMU_CCORE clocks names
clk: samsung: exynos7: Correct CMU_TOP1 clocks names
clk: samsung: exynos7: Correct CMU_TOP0 clocks names
clk: samsung: exynos7: Adds missing clocks gates of CMU_TOPC
clk: samsung: exynos7: Change the CMU_TOPC block clock names
clk: samsung: exynos7: Correct nr_clk_ids for fsys1
clk: samsung: exynos7: Correct nr_clk_ids for fsys0
clk: samsung: exynos7: Fix CMU TOP1 block
clk: samsung: exynos7: Fix CMU TOPC block clock
|
|
* clk-fixes: (3 commits)
clk: ti: dflt: fix enable_reg validity check
clk: ti: fix dual-registration of uart4_ick
clk: ti: clk-7xx: Remove hardwired ABE clock configuration
|
|
The patch adds mwidth and nwidth fields to the struct clk_fractional_divider
for further usage. While here, use GENMASK() instead of open coding this
functionality.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Previously we've only supported a few fixed clocks based on
assumptions about how the firmware sets up the clocks, but this
binding will let us control the actual (audio power domain) clock
manager.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add a new type of clocks that can be provided to a peripheral.
In addition to the peripheral clock, this new clock that can use several
input clocks as parents can generate divided rates.
This would allow a peripheral to have finer grained clocks for generating
a baud rate, clocking an asynchronous part or having more
options in frequency.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[sboyd@codeaurora.org: Transition to new clk_hw provider APIs]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add support for the new sama5d2 SoC and adapt capabilities.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add _MASK and _OFFSET values and cleanup register fields layout.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add REF2USB_TX clock support into MT8173 APMIXEDSYS. This clock
is needed by USB 3.0.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
|
|
Most multimedia subsystem clocks will be accessed by multiple
drivers, so it's a better way to manage these clocks in CCF.
This patch adds clock support for MM, IMG, VDEC, VENC and VENC_LT
subsystems.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
|
|
The dpi_ck clock can be removed because it not actually used
in topckgen and subsystems.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
|
|
Add 13mhz clock used by GPT timer in infracfg.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"This includes a iser-target series from Jenny + Sagi @ Mellanox that
addresses the few remaining active I/O shutdown bugs, along with a
patch to support zero-copy for immediate data payloads that gives a
nice performance improvement for small block WRITEs.
Also included are some recent >= v4.2 regression bug-fixes. The most
notable is a RCU conversion regression for SPC-3 PR registrations, and
recent removal of obsolete RFC-3720 markers that introduced a login
regression bug with MSFT iSCSI initiators.
Thanks to everyone who has been testing + reporting bugs for v4.x"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Avoid OFMarker + IFMarker negotiation
target: Make TCM_WRITE_PROTECT failure honor D_SENSE bit
target: Fix target_sense_desc_format NULL pointer dereference
target: Propigate backend read-only to core_tpg_add_lun
target: Fix PR registration + APTPL RCU conversion regression
iser-target: Skip data copy if all the command data comes as immediate
iser-target: Change the recv buffers posting logic
iser-target: Fix pending connections handling in target stack shutdown sequnce
iser-target: Remove np_ prefix from isert_np members
iser-target: Remove unused variables
iser-target: Put the reference on commands waiting for unsol data
iser-target: remove command with state ISTATE_REMOVE
|
|
Pull networking fixes from David Miller:
1) When we run a tap on netlink sockets, we have to copy mmap'd SKBs
instead of cloning them. From Daniel Borkmann.
2) When converting classical BPF into eBPF, fix the setting of the
source reg to BPF_REG_X. From Tycho Andersen.
3) Fix igmpv3/mldv2 report parsing in the bridge multicast code, from
Linus Lussing.
4) Fix dst refcounting for ipv6 tunnels, from Martin KaFai Lau.
5) Set NLM_F_REPLACE flag properly when replacing ipv6 routes, from
Roopa Prabhu.
6) Add some new cxgb4 PCI device IDs, from Hariprasad Shenai.
7) Fix headroom tests and SKB leaks in ipv6 fragmentation code, from
Florian Westphal.
8) Check DMA mapping errors in bna driver, from Ivan Vecera.
9) Several 8139cp bug fixes (dev_kfree_skb_any in interrupt context,
misclearing of interrupt status in TX timeout handler, etc.) from
David Woodhouse.
10) In tipc, reset SKB header pointer after skb_linearize(), from Erik
Hugne.
11) Fix autobind races et al. in netlink code, from Herbert Xu with
help from Tejun Heo and others.
12) Missing SET_NETDEV_DEV in sunvnet driver, from Sowmini Varadhan.
13) Fix various races in timewait timer and reqsk_queue_hadh_req, from
Eric Dumazet.
14) Fix array overruns in mac80211, from Johannes Berg and Dan
Carpenter.
15) Fix data race in rhashtable_rehash_one(), from Dmitriy Vyukov.
16) Fix race between poll_one_napi and napi_disable, from Neil Horman.
17) Fix byte order in geneve tunnel port config, from John W Linville.
18) Fix handling of ARP replies over lightweight tunnels, from Jiri
Benc.
19) We can loop when fib rule dumps cross multiple SKBs, fix from Wilson
Kok and Roopa Prabhu.
20) Several reference count handling bug fixes in the PHY/MDIO layer
from Russel King.
21) Fix lockdep splat in ppp_dev_uninit(), from Guillaume Nault.
22) Fix crash in icmp_route_lookup(), from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net: Fix panic in icmp_route_lookup
net: update docbook comment for __mdiobus_register()
ppp: fix lockdep splat in ppp_dev_uninit()
net: via/Kconfig: GENERIC_PCI_IOMAP required if PCI not selected
phy: marvell: add link partner advertised modes
net: fix net_device refcounting
phy: add phy_device_remove()
phy: fixed-phy: properly validate phy in fixed_phy_update_state()
net: fix phy refcounting in a bunch of drivers
of_mdio: fix MDIO phy device refcounting
phy: add proper phy struct device refcounting
phy: fix mdiobus module safety
net: dsa: fix of_mdio_find_bus() device refcount leak
phy: fix of_mdio_find_bus() device refcount leak
ip6_tunnel: Reduce log level in ip6_tnl_err() to debug
ip6_gre: Reduce log level in ip6gre_err() to debug
fib_rules: fix fib rule dumps across multiple skbs
bnx2x: byte swap rss_key to comply to Toeplitz specs
net: revert "net_sched: move tp->root allocation into fw_init()"
lwtunnel: remove source and destination UDP port config option
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull another cgroup fix from Tejun Heo:
"The cgroup writeback support got inadvertently enabled for traditional
hierarchies revealing two regressions which are currently being worked
on. It shouldn't have been enabled on traditional hierarchies, so
disable it on them. This is enough to make the regressions go away
for people who aren't experimenting with cgroup"
* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup, writeback: don't enable cgroup writeback on traditional hierarchies
|
|
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable patches:
- fix v4.2 SEEK on files over 2 gigs
- Fix a layout segment reference leak when pNFS I/O falls back to inband I/O.
- Fix recovery of recalled read delegations
Bugfixes:
- Fix a case where NFSv4 fails to send CLOSE after a server reboot
- Fix sunrpc to wait for connections to complete before retrying
- Fix sunrpc races between transport connect/disconnect and shutdown
- Fix an infinite loop when layoutget fail with BAD_STATEID
- nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
- Fix a bogus WARN_ON_ONCE() in O_DIRECT when layout commit_through_mds is set
- Fix layoutreturn/close ordering issues"
* tag 'nfs-for-4.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS41: make close wait for layoutreturn
NFS: Skip checking ds_cinfo.buckets when lseg's commit_through_mds is set
NFSv4.x/pnfs: Don't try to recover stateids twice in layoutget
NFSv4: Recovery of recalled read delegations is broken
NFS: Fix an infinite loop when layoutget fail with BAD_STATEID
NFS: Do cleanup before resetting pageio read/write to mds
SUNRPC: xs_sock_mark_closed() does not need to trigger socket autoclose
SUNRPC: Lock the transport layer on shutdown
nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
SUNRPC: Ensure that we wait for connections to complete before retrying
SUNRPC: drop null test before destroy functions
nfs: fix v4.2 SEEK on files over 2 gigs
SUNRPC: Fix races between socket connection and destroy code
nfs: fix pg_test page count calculation
Failing to send a CLOSE if file is opened WRONLY and server reboots on a 4.x mount
|
|
This patch adds a DF_READ_ONLY flag that is used by IBLOCK to
signal when a backend has been set to read-only mode, in order
to propigate read-only status up to core_tpg_add_lun() for all
future LUN fabric exports.
With this is place, existing emulation for reporting read-only
in spc_emulate_modesense() and normal transport_lookup_cmd_lun()
TCM_WRITE_PROTECTED status checking just works as expected.
Reported-by: Joeue Deng <joeue404@gmail.com>
Reported-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Add a phy_device_remove() function to complement phy_device_register(),
which undoes the effects of phy_device_register() by removing the phy
device from visibility, but not freeing it.
This allows these details to be moved out of the mdio bus code into
the phy code where this action belongs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-implement the mdiobus module refcounting to ensure that we actually
ensure that the mdiobus module code does not go away while we might call
into it.
The old scheme using bus->dev.driver was buggy, because bus->dev is a
class device which never has a struct device_driver associated with it,
and hence the associated code trying to obtain a refcount did nothing
useful.
Instead, take the approach that other subsystems do: pass the module
when calling mdiobus_register(), and record that in the mii_bus struct.
When we need to increment the module use count in the phy code, use
this stored pointer. When the phy is deteched, drop the module
refcount, remembering that the phy device might go away at that point.
This doesn't stop the mii_bus going away while there are in-use phys -
it merely stops the underlying code vanishing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
- Power allocator governor changes to allow binding on thermal zones
with missing power estimates information. From Javi Merino.
- Add compile test flags on thermal drivers that allow it without
producing compilation errors. From Eduardo Valentin.
- Fixes around memory allocation on cpu_cooling. From Javi Merino.
- Fix on db8500 cpufreq code to allow autoload. From Luis de
Bethencourt.
- Maintainer entries for cpu cooling device
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: power_allocator: exit early if there are no cooling devices
thermal: power_allocator: don't require tzp to be present for the thermal zone
thermal: power_allocator: relax the requirement of two passive trip points
thermal: power_allocator: relax the requirement of a sustainable_power in tzp
thermal: Add a function to get the minimum power
thermal: cpu_cooling: free power table on error or when unregistering
thermal: cpu_cooling: don't call kcalloc() under rcu_read_lock
thermal: db8500_cpufreq_cooling: Fix module autoload for OF platform driver
thermal: cpu_cooling: Add MAINTAINERS entry
thermal: ti-soc: Kconfig fix to avoid menu showing wrongly
thermal: ti-soc: allow compile test
thermal: qcom_spmi: allow compile test
thermal: exynos: allow compile test
thermal: armada: allow compile test
thermal: dove: allow compile test
thermal: kirkwood: allow compile test
thermal: rockchip: allow compile test
thermal: spear: allow compile test
thermal: hisi: allow compile test
thermal: Fix thermal_zone_of_sensor_register to match documentation
|
|
Merge misc fixes from Andrew Morton:
"15 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
ocfs2/dlm: fix deadlock when dispatch assert master
membarrier: clean up selftest
vmscan: fix sane_reclaim helper for legacy memcg
lib/iommu-common.c: do not try to deref a null iommu->lazy_flush() pointer when n < pool->hint
x86, efi, kasan: #undef memset/memcpy/memmove per arch
mm: migrate: hugetlb: putback destination hugepage to active list
mm, dax: VMA with vm_ops->pfn_mkwrite wants to be write-notified
userfaultfd: register uapi generic syscall (aarch64)
userfaultfd: selftest: don't error out if pthread_mutex_t isn't identical
userfaultfd: selftest: return an error if BOUNCE_VERIFY fails
userfaultfd: selftest: avoid my_bcmp false positives with powerpc
userfaultfd: selftest: only warn if __NR_userfaultfd is undefined
userfaultfd: selftest: headers fixup
userfaultfd: selftests: vm: pick up sanitized kernel headers
userfaultfd: revert "userfaultfd: waitqueue: add nr wake parameter to __wake_up_locked_key"
|
|
The UDP tunnel config is asymmetric wrt. to the ports used. The source and
destination ports from one direction of the tunnel are not related to the
ports of the other direction. We need to be able to respond to ARP requests
using the correct ports without involving routing.
As the consequence, UDP ports need to be fixed property of the tunnel
interface and cannot be set per route. Remove the ability to set ports per
route. This is still okay to do, as no kernel has been released with these
attributes yet.
Note that the ability to specify source and destination ports is preserved
for other users of the lwtunnel API which don't use routes for tunnel key
specification (like openvswitch).
If in the future we rework ARP handling to allow port specification, the
attributes can be added back.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using ip lwtunnels, the additional data for xmit (basically, the actual
tunnel to use) are carried in ip_tunnel_info either in dst->lwtstate or in
metadata dst. When replying to ARP requests, we need to send the reply to
the same tunnel the request came from. This means we need to construct
proper metadata dst for ARP replies.
We could perform another route lookup to get a dst entry with the correct
lwtstate. However, this won't always ensure that the outgoing tunnel is the
same as the incoming one, and it won't work anyway for IPv4 duplicate
address detection.
The only thing to do is to "reverse" the ip_tunnel_info.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VXLAN device can receive skb with checksum partial. But the checksum
offset could be in outer header which is pulled on receive. This results
in negative checksum offset for the skb. Such skb can cause the assert
failure in skb_checksum_help(). Following patch fixes the bug by setting
checksum-none while pulling outer header.
Following is the kernel panic msg from old kernel hitting the bug.
------------[ cut here ]------------
kernel BUG at net/core/dev.c:1906!
RIP: 0010:[<ffffffff81518034>] skb_checksum_help+0x144/0x150
Call Trace:
<IRQ>
[<ffffffffa0164c28>] queue_userspace_packet+0x408/0x470 [openvswitch]
[<ffffffffa016614d>] ovs_dp_upcall+0x5d/0x60 [openvswitch]
[<ffffffffa0166236>] ovs_dp_process_packet_with_key+0xe6/0x100 [openvswitch]
[<ffffffffa016629b>] ovs_dp_process_received_packet+0x4b/0x80 [openvswitch]
[<ffffffffa016c51a>] ovs_vport_receive+0x2a/0x30 [openvswitch]
[<ffffffffa0171383>] vxlan_rcv+0x53/0x60 [openvswitch]
[<ffffffffa01734cb>] vxlan_udp_encap_recv+0x8b/0xf0 [openvswitch]
[<ffffffff8157addc>] udp_queue_rcv_skb+0x2dc/0x3b0
[<ffffffff8157b56f>] __udp4_lib_rcv+0x1cf/0x6c0
[<ffffffff8157ba7a>] udp_rcv+0x1a/0x20
[<ffffffff8154fdbd>] ip_local_deliver_finish+0xdd/0x280
[<ffffffff81550128>] ip_local_deliver+0x88/0x90
[<ffffffff8154fa7d>] ip_rcv_finish+0x10d/0x370
[<ffffffff81550365>] ip_rcv+0x235/0x300
[<ffffffff8151ba1d>] __netif_receive_skb+0x55d/0x620
[<ffffffff8151c360>] netif_receive_skb+0x80/0x90
[<ffffffff81459935>] virtnet_poll+0x555/0x6f0
[<ffffffff8151cd04>] net_rx_action+0x134/0x290
[<ffffffff810683d8>] __do_softirq+0xa8/0x210
[<ffffffff8162fe6c>] call_softirq+0x1c/0x30
[<ffffffff810161a5>] do_softirq+0x65/0xa0
[<ffffffff810687be>] irq_exit+0x8e/0xb0
[<ffffffff81630733>] do_IRQ+0x63/0xe0
[<ffffffff81625f2e>] common_interrupt+0x6e/0x6e
Reported-by: Anupam Chanda <achanda@vmware.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inode_cgwb_enabled() gates cgroup writeback support. If it returns
true, each inode is attached to the corresponding memory domain which
gets mapped to io domain. It currently only tests whether the
filesystem and bdi support cgroup writeback; however, cgroup writeback
support doesn't work on traditional hierarchies and thus it should
also test whether memcg and iocg are on the default hierarchy.
This caused traditional hierarchy setups to hit the cgroup writeback
path inadvertently and ended up creating separate writeback domains
for each memcg and mapping them all to the root iocg uncovering a
couple issues in the cgroup writeback path.
cgroup writeback was never meant to be enabled on traditional
hierarchies. Make inode_cgwb_enabled() test whether both memcg and
iocg are on the default hierarchy.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Artem Bityutskiy <dedekind1@gmail.com>
Reported-by: Dexuan Cui <decui@microsoft.com>
Link: http://lkml.kernel.org/g/1443012552.19983.209.camel@gmail.com
Link: http://lkml.kernel.org/g/f30d4a6aa8a546ff88f73021d026a453@SIXPR30MB031.064d.mgd.msft.net
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A disappointingly large collection of fixes for SPI issues, though
almost all in drivers (and there mainly the newly added Mediatek
driver) and the core fixes are documentation and error handling.
The driver fixes are all of the usual 'important if you see them'
variety"
* tag 'spi-fix-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: xtensa-xtfpga: fix register endianness
spi: meson: Fix module autoload for OF platform driver
spi: mediatek: fix wrong error return value on probe
spi: fix kernel-doc warnings in spi.h
spi: spidev: fix possible NULL dereference
spi: atmel: remove warning when !CONFIG_PM_SLEEP
spi: bcm2835: BUG: fix wrong use of PAGE_MASK
spi: mediatek: fix spi cs polarity error
spi: Fix documentation of spi_alloc_master()
spi: spi-pxa2xx: Check status register to determine if SSSR_TINT is disabled
spi: Mediatek: Document devicetree bindings update for spi bus
spi: mediatek: fix spi clock usage error
spi: mediatek: remove clk_disable_unprepare()
|
|
Drivers might call napi_disable while not holding the napi instance poll_lock.
In those instances, its possible for a race condition to exist between
poll_one_napi and napi_disable. That is to say, poll_one_napi only tests the
NAPI_STATE_SCHED bit to see if there is work to do during a poll, and as such
the following may happen:
CPU0 CPU1
ndo_tx_timeout napi_poll_dev
napi_disable poll_one_napi
test_and_set_bit (ret 0)
test_bit (ret 1)
reset adapter napi_poll_routine
If the adapter gets a tx timeout without a napi instance scheduled, its possible
for the adapter to think it has exclusive access to the hardware (as the napi
instance is now scheduled via the napi_disable call), while the netpoll code
thinks there is simply work to do. The result is parallel hardware access
leading to corrupt data structures in the driver, and a crash.
Additionaly, there is another, more critical race between netpoll and
napi_disable. The disabled napi state is actually identical to the scheduled
state for a given napi instance. The implication being that, if a napi instance
is disabled, a netconsole instance would see the napi state of the device as
having been scheduled, and poll it, likely while the driver was dong something
requiring exclusive access. In the case above, its fairly clear that not having
the rings in a state ready to be polled will cause any number of crashes.
The fix should be pretty easy. netpoll uses its own bit to indicate that that
the napi instance is in a state of being serviced by netpoll (NAPI_STATE_NPSVC).
We can just gate disabling on that bit as well as the sched bit. That should
prevent netpoll from conducting a napi poll if we convert its set bit to a
test_and_set_bit operation to provide mutual exclusion
Change notes:
V2)
Remove a trailing whtiespace
Resubmit with proper subject prefix
V3)
Clean up spacing nits
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: jmaxwell@redhat.com
Tested-by: jmaxwell@redhat.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add clock support for Vybrid On-Chip One Time Programmable
(OCOTP) controller.
While the OCOTP block does not require explicit clock gating,
for programming the OCOTP timing register the clock rate of
ipg clock is required for timing calculations related to fuse
and shadow register read sequence. We explicitly specify the
ipg clock for OCOTP as a result.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the userfaultfd syscalls to uapi asm-generic, it was tested with
postcopy live migration on aarch64 with both 4k and 64k pagesize
kernels.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__wake_up_locked_key"
This reverts commit 51360155eccb907ff8635bd10fc7de876408c2e0 and adapts
fs/userfaultfd.c to use the old version of that function.
It didn't look robust to call __wake_up_common with "nr == 1" when we
absolutely require wakeall semantics, but we've full control of what we
insert in the two waitqueue heads of the blocked userfaults. No
exclusive waitqueue risks to be inserted into those two waitqueue heads
so we can as well stick to "nr == 1" of the old code and we can rely
purely on the fact no waitqueue inserted in one of the two waitqueue
heads we must enforce as wakeall, has wait->flags WQ_FLAG_EXCLUSIVE set.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
'spi/fix/doc', 'spi/fix/mediatek', 'spi/fix/meson', 'spi/fix/mtk' and 'spi/fix/pxa2xx' into spi-linus
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"The threadgroup locking changes which went in during 4.2 devel cycle
added write locking of a percpu_rwsem in cgroup task migration path;
unfortunately, that involved expedited rcu syncing which turned out to
be too slow and heavy for certain workloads. The patchset which is
dependent on this one didn't get committed during that devel cycle, so
these two patches can be reverted safely.
Oleg reworked percpu_rwsem for 4.4 so that the writer path is a lot
lighter. The reported issue goes away with Oleg's reworked
percpu_rwsem and I'll reapply these patches on the for-4.4 branch so
that they can land together with Oleg's changes"
* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
Revert "sched, cgroup: replace signal_struct->group_rwsem with a global percpu_rwsem"
Revert "cgroup: simplify threadgroup locking"
|
|
When creating a timewait socket, we need to arm the timer before
allowing other cpus to find it. The signal allowing cpus to find
the socket is setting tw_refcnt to non zero value.
As we set tw_refcnt in __inet_twsk_hashdance(), we therefore need to
call inet_twsk_schedule() first.
This also means we need to remove tw_refcnt changes from
inet_twsk_schedule() and let the caller handle it.
Note that because we use mod_timer_pinned(), we have the guarantee
the timer wont expire before we set tw_refcnt as we run in BH context.
To make things more readable I introduced inet_twsk_reschedule() helper.
When rearming the timer, we can use mod_timer_pending() to make sure
we do not rearm a canceled timer.
Note: This bug can possibly trigger if packets of a flow can hit
multiple cpus. This does not normally happen, unless flow steering
is broken somehow. This explains this bug was spotted ~5 months after
its introduction.
A similar fix is needed for SYN_RECV sockets in reqsk_queue_hash_req(),
but will be provided in a separate patch for proper tracking.
Fixes: 789f558cfb36 ("tcp/dccp: get rid of central timewait timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ying Cai <ycai@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like the previous patch, which fixes ipv4 tunnels, here is the ipv6 part.
Before the patch, the external ipv6 header + gre header were included on
tx.
After the patch:
$ ping -c1 192.168.6.121 ; ip -s l ls dev ip6gre1
PING 192.168.6.121 (192.168.6.121) 56(84) bytes of data.
64 bytes from 192.168.6.121: icmp_req=1 ttl=64 time=1.92 ms
--- 192.168.6.121 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 1.923/1.923/1.923/0.000 ms
7: ip6gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1440 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/gre6 20:01:06:60:30:08:c1:c3:00:00:00:00:00:00:01:23 peer 20:01:06:60:30:08:c1:c3:00:00:00:00:00:00:01:21
RX: bytes packets errors dropped overrun mcast
84 1 0 0 0 0
TX: bytes packets errors dropped carrier collsns
84 1 0 0 0 0
$ ping -c1 192.168.1.121 ; ip -s l ls dev ip6tnl1
PING 192.168.1.121 (192.168.1.121) 56(84) bytes of data.
64 bytes from 192.168.1.121: icmp_req=1 ttl=64 time=2.28 ms
--- 192.168.1.121 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 2.288/2.288/2.288/0.000 ms
8: ip6tnl1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1452 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/tunnel6 2001:660:3008:c1c3::123 peer 2001:660:3008:c1c3::121
RX: bytes packets errors dropped overrun mcast
84 1 0 0 0 0
TX: bytes packets errors dropped carrier collsns
84 1 0 0 0 0
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patch contains Netfilter fixes for your net tree, they are:
1) nf_log_unregister() should only set to NULL the logger that is being
unregistered, instead of everything else. Patch from Florian Westphal.
2) Fix a crash when accessing physoutdev from PREROUTING in br_netfilter.
This is partially reverting the patch to shrink nf_bridge_info to 32 bytes.
Also from Florian.
3) Use existing match/target extensions in the internal nft_compat extension
lists when the extension is family unspecific (ie. NFPROTO_UNSPEC).
4) Wait for rcu grace period before leaving nf_log_unregister().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Man page of ip-route(8) says following about route types:
unreachable - these destinations are unreachable. Packets are dis‐
carded and the ICMP message host unreachable is generated. The local
senders get an EHOSTUNREACH error.
blackhole - these destinations are unreachable. Packets are dis‐
carded silently. The local senders get an EINVAL error.
prohibit - these destinations are unreachable. Packets are discarded
and the ICMP message communication administratively prohibited is
generated. The local senders get an EACCES error.
In the inet6 address family, this was correct, except the local senders
got ENETUNREACH error instead of EHOSTUNREACH in case of unreachable route.
In the inet address family, all three route types generated ICMP message
net unreachable, and the local senders got ENETUNREACH error.
In both address families all three route types now behave consistently
with documentation.
Signed-off-by: Nikola Forró <nforro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jann Horn <jann@thejh.net>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Included are: a somewhat late devfreq update which however is mostly
fixes and cleanups with one new thing only (the PPMUv2 support on
Exynos5433), an ACPI cpufreq driver fixup and two ACPI core cleanups
related to preprocessor directives.
Specifics:
- Fix a memory allocation size in the devfreq core (Xiaolong Ye).
- Fix a mistake in the exynos-ppmu DT binding (Javier Martinez
Canillas).
- Add support for PPMUv2 ((Platform Performance Monitoring Unit
version 2.0) on the Exynos5433 SoCs (Chanwoo Choi).
- Fix a type casting bug in the Exynos PPMU code (MyungJoo Ham).
- Assorted devfreq code cleanups and optimizations (Javi Merino,
MyungJoo Ham, Viresh Kumar).
- Fix up the ACPI cpufreq driver to use a more lightweight way to get
to its private data in the ->get() callback (Rafael J Wysocki).
- Fix a CONFIG_ prefix bug in one of the ACPI drivers and make the
ACPI subsystem use IS_ENABLED() instead of #ifdefs in function
bodies (Sudeep Holla)"
* tag 'pm+acpi-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: acpi-cpufreq: Use cpufreq_cpu_get_raw() in ->get()
ACPI: Eliminate CONFIG_.*{, _MODULE} #ifdef in favor of IS_ENABLED()
ACPI: int340x_thermal: add missing CONFIG_ prefix
PM / devfreq: Fix incorrect type issue.
PM / devfreq: tegra: Update governor to use devfreq_update_stats()
PM / devfreq: comments for get_dev_status usage updated
PM / devfreq: drop comment about thermal setting max_freq
PM / devfreq: cache the last call to get_dev_status()
PM / devfreq: Drop unlikely before IS_ERR(_OR_NULL)
PM / devfreq: exynos-ppmu: bit-wise operation bugfix.
PM / devfreq: exynos-ppmu: Update documentation to support PPMUv2
PM / devfreq: exynos-ppmu: Add the support of PPMUv2 for Exynos5433
PM / devfreq: event: Remove incorrect property in exynos-ppmu DT binding
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"The new hfi1 driver in staging/rdma has had a number of fixup patches
since being added to the tree. This is the first batch of those fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/hfi: Properly set permissions for user device files
IB/hfi1: mask vs shift confusion
IB/hfi1: clean up some defines
IB/hfi1: info leak in get_ctxt_info()
IB/hfi1: fix a locking bug
IB/hfi1: checking for NULL instead of IS_ERR
IB/hfi1: fix sdma_descq_cnt parameter parsing
IB/hfi1: fix copy_to/from_user() error handling
IB/hfi1: fix pstateinfo from returning improperly byteswapped value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- a boot regression (since v4.2) fix for some ARM configurations from
Tyler
- regression (since v4.1) fixes for mkfs.xfs on a DAX enabled device
from Jeff. These are tagged for -stable.
- a pair of locking fixes from Axel that are hidden from lockdep since
they involve device_lock(). The "btt" one is tagged for -stable, the
other only applies to the new "pfn" mechanism in v4.3.
- a fix for the pmem ->rw_page() path to use wmb_pmem() from Ross.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
mm: fix type cast in __pfn_to_phys()
pmem: add proper fencing to pmem_rw_page()
libnvdimm: pfn_devs: Fix locking in namespace_store
libnvdimm: btt_devs: Fix locking in namespace_store
blockdev: don't set S_DAX for misaligned partitions
dax: fix O_DIRECT I/O to the last block of a blockdev
|
|
Pull block updates from Jens Axboe:
"This is a bit bigger than it should be, but I could (did) not want to
send it off last week due to both wanting extra testing, and expecting
a fix for the bounce regression as well. In any case, this contains:
- Fix for the blk-merge.c compilation warning on gcc 5.x from me.
- A set of back/front SG gap merge fixes, from me and from Sagi.
This ensures that we honor SG gapping for integrity payloads as
well.
- Two small fixes for null_blk from Matias, fixing a leak and a
capacity propagation issue.
- A blkcg fix from Tejun, fixing a NULL dereference.
- A fast clone optimization from Ming, fixing a performance
regression since the arbitrarily sized bio's were introduced.
- Also from Ming, a regression fix for bouncing IOs"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix bounce_end_io
block: blk-merge: fast-clone bio when splitting rw bios
block: blkg_destroy_all() should clear q->root_blkg and ->root_rl.blkg
block: Copy a user iovec if it includes gaps
block: Refuse adding appending a gapped integrity page to a bio
block: Refuse request/bio merges with gaps in the integrity payload
block: Check for gaps on front and back merges
null_blk: fix wrong capacity when bs is not 512 bytes
null_blk: fix memory leak on cleanup
block: fix bogus compiler warnings in blk-merge.c
|
|
The various definitions of __pfn_to_phys() have been consolidated to
use a generic macro in include/asm-generic/memory_model.h. This hit
mainline in the form of 012dcef3f058 "mm: move __phys_to_pfn and
__pfn_to_phys to asm/generic/memory_model.h". When the generic macro
was implemented the type cast to phys_addr_t was dropped which caused
boot regressions on ARM platforms with more than 4GB of memory and
LPAE enabled.
It was suggested to use PFN_PHYS() defined in include/linux/pfn.h
as provides the correct logic and avoids further duplication.
Reported-by: kernelci.org bot <bot@kernelci.org>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
