| Age | Commit message (Collapse) | Author |
|---|
|
commit 9c80e79906b4ca440d09e7f116609262bb747909 upstream.
The assumption in __disable_kprobe() is wrong, and it could try to disarm
an already disarmed kprobe and fire the WARN_ONCE() below. [0] We can
easily reproduce this issue.
1. Write 0 to /sys/kernel/debug/kprobes/enabled.
# echo 0 > /sys/kernel/debug/kprobes/enabled
2. Run execsnoop. At this time, one kprobe is disabled.
# /usr/share/bcc/tools/execsnoop &
[1] 2460
PCOMM PID PPID RET ARGS
# cat /sys/kernel/debug/kprobes/list
ffffffff91345650 r __x64_sys_execve+0x0 [FTRACE]
ffffffff91345650 k __x64_sys_execve+0x0 [DISABLED][FTRACE]
3. Write 1 to /sys/kernel/debug/kprobes/enabled, which changes
kprobes_all_disarmed to false but does not arm the disabled kprobe.
# echo 1 > /sys/kernel/debug/kprobes/enabled
# cat /sys/kernel/debug/kprobes/list
ffffffff91345650 r __x64_sys_execve+0x0 [FTRACE]
ffffffff91345650 k __x64_sys_execve+0x0 [DISABLED][FTRACE]
4. Kill execsnoop, when __disable_kprobe() calls disarm_kprobe() for the
disabled kprobe and hits the WARN_ONCE() in __disarm_kprobe_ftrace().
# fg
/usr/share/bcc/tools/execsnoop
^C
Actually, WARN_ONCE() is fired twice, and __unregister_kprobe_top() misses
some cleanups and leaves the aggregated kprobe in the hash table. Then,
__unregister_trace_kprobe() initialises tk->rp.kp.list and creates an
infinite loop like this.
aggregated kprobe.list -> kprobe.list -.
^ |
'.__.'
In this situation, these commands fall into the infinite loop and result
in RCU stall or soft lockup.
cat /sys/kernel/debug/kprobes/list : show_kprobe_addr() enters into the
infinite loop with RCU.
/usr/share/bcc/tools/execsnoop : warn_kprobe_rereg() holds kprobe_mutex,
and __get_valid_kprobe() is stuck in
the loop.
To avoid the issue, make sure we don't call disarm_kprobe() for disabled
kprobes.
[0]
Failed to disarm kprobe-ftrace at __x64_sys_execve+0x0/0x40 (error -2)
WARNING: CPU: 6 PID: 2460 at kernel/kprobes.c:1130 __disarm_kprobe_ftrace.isra.19 (kernel/kprobes.c:1129)
Modules linked in: ena
CPU: 6 PID: 2460 Comm: execsnoop Not tainted 5.19.0+ #28
Hardware name: Amazon EC2 c5.2xlarge/, BIOS 1.0 10/16/2017
RIP: 0010:__disarm_kprobe_ftrace.isra.19 (kernel/kprobes.c:1129)
Code: 24 8b 02 eb c1 80 3d c4 83 f2 01 00 75 d4 48 8b 75 00 89 c2 48 c7 c7 90 fa 0f 92 89 04 24 c6 05 ab 83 01 e8 e4 94 f0 ff <0f> 0b 8b 04 24 eb b1 89 c6 48 c7 c7 60 fa 0f 92 89 04 24 e8 cc 94
RSP: 0018:ffff9e6ec154bd98 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffffff930f7b00 RCX: 0000000000000001
RDX: 0000000080000001 RSI: ffffffff921461c5 RDI: 00000000ffffffff
RBP: ffff89c504286da8 R08: 0000000000000000 R09: c0000000fffeffff
R10: 0000000000000000 R11: ffff9e6ec154bc28 R12: ffff89c502394e40
R13: ffff89c502394c00 R14: ffff9e6ec154bc00 R15: 0000000000000000
FS: 00007fe800398740(0000) GS:ffff89c812d80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000c00057f010 CR3: 0000000103b54006 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
__disable_kprobe (kernel/kprobes.c:1716)
disable_kprobe (kernel/kprobes.c:2392)
__disable_trace_kprobe (kernel/trace/trace_kprobe.c:340)
disable_trace_kprobe (kernel/trace/trace_kprobe.c:429)
perf_trace_event_unreg.isra.2 (./include/linux/tracepoint.h:93 kernel/trace/trace_event_perf.c:168)
perf_kprobe_destroy (kernel/trace/trace_event_perf.c:295)
_free_event (kernel/events/core.c:4971)
perf_event_release_kernel (kernel/events/core.c:5176)
perf_release (kernel/events/core.c:5186)
__fput (fs/file_table.c:321)
task_work_run (./include/linux/sched.h:2056 (discriminator 1) kernel/task_work.c:179 (discriminator 1))
exit_to_user_mode_prepare (./include/linux/resume_user_mode.h:49 kernel/entry/common.c:169 kernel/entry/common.c:201)
syscall_exit_to_user_mode (./arch/x86/include/asm/jump_label.h:55 ./arch/x86/include/asm/nospec-branch.h:384 ./arch/x86/include/asm/entry-common.h:94 kernel/entry/common.c:133 kernel/entry/common.c:296)
do_syscall_64 (arch/x86/entry/common.c:87)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
RIP: 0033:0x7fe7ff210654
Code: 15 79 89 20 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb be 0f 1f 00 8b 05 9a cd 20 00 48 63 ff 85 c0 75 11 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 3a f3 c3 48 83 ec 18 48 89 7c 24 08 e8 34 fc
RSP: 002b:00007ffdbd1d3538 EFLAGS: 00000246 ORIG_RAX: 0000000000000003
RAX: 0000000000000000 RBX: 0000000000000008 RCX: 00007fe7ff210654
RDX: 0000000000000000 RSI: 0000000000002401 RDI: 0000000000000008
RBP: 0000000000000000 R08: 94ae31d6fda838a4 R0900007fe8001c9d30
R10: 00007ffdbd1d34b0 R11: 0000000000000246 R12: 00007ffdbd1d3600
R13: 0000000000000000 R14: fffffffffffffffc R15: 00007ffdbd1d3560
</TASK>
Link: https://lkml.kernel.org/r/20220813020509.90805-1-kuniyu@amazon.com
Fixes: 69d54b916d83 ("kprobes: makes kprobes/enabled works correctly for optimized kprobes.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reported-by: Ayushman Dutta <ayudutta@amazon.com>
Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Kuniyuki Iwashima <kuniyu@amazon.com>
Cc: Kuniyuki Iwashima <kuni1840@gmail.com>
Cc: Ayushman Dutta <ayudutta@amazon.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c3b0f72e805f0801f05fa2aa52011c4bfc694c44 upstream.
ftrace_startup does not remove ops from ftrace_ops_list when
ftrace_startup_enable fails:
register_ftrace_function
ftrace_startup
__register_ftrace_function
...
add_ftrace_ops(&ftrace_ops_list, ops)
...
...
ftrace_startup_enable // if ftrace failed to modify, ftrace_disabled is set to 1
...
return 0 // ops is in the ftrace_ops_list.
When ftrace_disabled = 1, unregister_ftrace_function simply returns without doing anything:
unregister_ftrace_function
ftrace_shutdown
if (unlikely(ftrace_disabled))
return -ENODEV; // return here, __unregister_ftrace_function is not executed,
// as a result, ops is still in the ftrace_ops_list
__unregister_ftrace_function
...
If ops is dynamically allocated, it will be free later, in this case,
is_ftrace_trampoline accesses NULL pointer:
is_ftrace_trampoline
ftrace_ops_trampoline
do_for_each_ftrace_op(op, ftrace_ops_list) // OOPS! op may be NULL!
Syzkaller reports as follows:
[ 1203.506103] BUG: kernel NULL pointer dereference, address: 000000000000010b
[ 1203.508039] #PF: supervisor read access in kernel mode
[ 1203.508798] #PF: error_code(0x0000) - not-present page
[ 1203.509558] PGD 800000011660b067 P4D 800000011660b067 PUD 130fb8067 PMD 0
[ 1203.510560] Oops: 0000 [#1] SMP KASAN PTI
[ 1203.511189] CPU: 6 PID: 29532 Comm: syz-executor.2 Tainted: G B W 5.10.0 #8
[ 1203.512324] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[ 1203.513895] RIP: 0010:is_ftrace_trampoline+0x26/0xb0
[ 1203.514644] Code: ff eb d3 90 41 55 41 54 49 89 fc 55 53 e8 f2 00 fd ff 48 8b 1d 3b 35 5d 03 e8 e6 00 fd ff 48 8d bb 90 00 00 00 e8 2a 81 26 00 <48> 8b ab 90 00 00 00 48 85 ed 74 1d e8 c9 00 fd ff 48 8d bb 98 00
[ 1203.518838] RSP: 0018:ffffc900012cf960 EFLAGS: 00010246
[ 1203.520092] RAX: 0000000000000000 RBX: 000000000000007b RCX: ffffffff8a331866
[ 1203.521469] RDX: 0000000000000000 RSI: 0000000000000008 RDI: 000000000000010b
[ 1203.522583] RBP: 0000000000000000 R08: 0000000000000000 R09: ffffffff8df18b07
[ 1203.523550] R10: fffffbfff1be3160 R11: 0000000000000001 R12: 0000000000478399
[ 1203.524596] R13: 0000000000000000 R14: ffff888145088000 R15: 0000000000000008
[ 1203.525634] FS: 00007f429f5f4700(0000) GS:ffff8881daf00000(0000) knlGS:0000000000000000
[ 1203.526801] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1203.527626] CR2: 000000000000010b CR3: 0000000170e1e001 CR4: 00000000003706e0
[ 1203.528611] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1203.529605] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Therefore, when ftrace_startup_enable fails, we need to rollback registration
process and remove ops from ftrace_ops_list.
Link: https://lkml.kernel.org/r/20220818032659.56209-1-yangjihong1@huawei.com
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a657182a5c5150cdfacb6640aad1d2712571a409 upstream.
Hsin-Wei reported a KASAN splat triggered by their BPF runtime fuzzer which
is based on a customized syzkaller:
BUG: KASAN: slab-out-of-bounds in bpf_int_jit_compile+0x1257/0x13f0
Read of size 8 at addr ffff888004e90b58 by task syz-executor.0/1489
CPU: 1 PID: 1489 Comm: syz-executor.0 Not tainted 5.19.0 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x9c/0xc9
print_address_description.constprop.0+0x1f/0x1f0
? bpf_int_jit_compile+0x1257/0x13f0
kasan_report.cold+0xeb/0x197
? kvmalloc_node+0x170/0x200
? bpf_int_jit_compile+0x1257/0x13f0
bpf_int_jit_compile+0x1257/0x13f0
? arch_prepare_bpf_dispatcher+0xd0/0xd0
? rcu_read_lock_sched_held+0x43/0x70
bpf_prog_select_runtime+0x3e8/0x640
? bpf_obj_name_cpy+0x149/0x1b0
bpf_prog_load+0x102f/0x2220
? __bpf_prog_put.constprop.0+0x220/0x220
? find_held_lock+0x2c/0x110
? __might_fault+0xd6/0x180
? lock_downgrade+0x6e0/0x6e0
? lock_is_held_type+0xa6/0x120
? __might_fault+0x147/0x180
__sys_bpf+0x137b/0x6070
? bpf_perf_link_attach+0x530/0x530
? new_sync_read+0x600/0x600
? __fget_files+0x255/0x450
? lock_downgrade+0x6e0/0x6e0
? fput+0x30/0x1a0
? ksys_write+0x1a8/0x260
__x64_sys_bpf+0x7a/0xc0
? syscall_enter_from_user_mode+0x21/0x70
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f917c4e2c2d
The problem here is that a range of tnum_range(0, map->max_entries - 1) has
limited ability to represent the concrete tight range with the tnum as the
set of resulting states from value + mask can result in a superset of the
actual intended range, and as such a tnum_in(range, reg->var_off) check may
yield true when it shouldn't, for example tnum_range(0, 2) would result in
00XX -> v = 0000, m = 0011 such that the intended set of {0, 1, 2} is here
represented by a less precise superset of {0, 1, 2, 3}. As the register is
known const scalar, really just use the concrete reg->var_off.value for the
upper index check.
Fixes: d2e4c1e6c294 ("bpf: Constant map key tracking for prog array pokes")
Reported-by: Hsin-Wei Hung <hsinweih@uci.edu>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/984b37f9fdf7ac36831d2137415a4a915744c1b6.1661462653.git.daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a8faed3a02eeb75857a3b5d660fa80fe79db77a3 upstream.
When CONFIG_ADVISE_SYSCALLS is not set/enabled and CONFIG_COMPAT is
set/enabled, the riscv compat_syscall_table references
'compat_sys_fadvise64_64', which is not defined:
riscv64-linux-ld: arch/riscv/kernel/compat_syscall_table.o:(.rodata+0x6f8):
undefined reference to `compat_sys_fadvise64_64'
Add 'fadvise64_64' to kernel/sys_ni.c as a conditional COMPAT function so
that when CONFIG_ADVISE_SYSCALLS is not set, there is a fallback function
available.
Link: https://lkml.kernel.org/r/20220807220934.5689-1-rdunlap@infradead.org
Fixes: d3ac21cacc24 ("mm: Support compiling out madvise and fadvise")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 763f4fb76e24959c370cdaa889b2492ba6175580 upstream.
Root cause:
The rebind_subsystems() is no lock held when move css object from A
list to B list,then let B's head be treated as css node at
list_for_each_entry_rcu().
Solution:
Add grace period before invalidating the removed rstat_css_node.
Reported-by: Jing-Ting Wu <jing-ting.wu@mediatek.com>
Suggested-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Jing-Ting Wu <jing-ting.wu@mediatek.com>
Tested-by: Jing-Ting Wu <jing-ting.wu@mediatek.com>
Link: https://lore.kernel.org/linux-arm-kernel/d8f0bc5e2fb6ed259f9334c83279b4c011283c41.camel@mediatek.com/T/
Acked-by: Mukesh Ojha <quic_mojha@quicinc.com>
Fixes: a7df69b81aac ("cgroup: rstat: support cgroup1")
Cc: stable@vger.kernel.org # v5.13+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ad982c3be4e60c7d39c03f782733503cbd88fd2a upstream.
Audit_alloc_mark() assign pathname to audit_mark->path, on error path
from fsnotify_add_inode_mark(), fsnotify_put_mark will free memory
of audit_mark->path, but the caller of audit_alloc_mark will free
the pathname again, so there will be double free problem.
Fix this by resetting audit_mark->path to NULL pointer on error path
from fsnotify_add_inode_mark().
Cc: stable@vger.kernel.org
Fixes: 7b1293234084d ("fsnotify: Add group pointer in fsnotify_init_mark()")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7c56a8733d0a2a4be2438a7512566e5ce552fccf ]
In some circumstances it may be interesting to reconfigure the watchdog
from inside the kernel.
On PowerPC, this may helpful before and after a LPAR migration (LPM) is
initiated, because it implies some latencies, watchdog, and especially NMI
watchdog is expected to be triggered during this operation. Reconfiguring
the watchdog with a factor, would prevent it to happen too frequently
during LPM.
Rename lockup_detector_reconfigure() as __lockup_detector_reconfigure() and
create a new function lockup_detector_reconfigure() calling
__lockup_detector_reconfigure() under the protection of watchdog_mutex.
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
[mpe: Squash in build fix from Laurent, reported by Sachin]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220713154729.80789-3-ldufour@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f04dec93466a0481763f3b56cdadf8076e28bfbf upstream.
Currently when an event probe (eprobe) hooks to a string field, it does
not display it as a string, but instead as a number. This makes the field
rather useless. Handle the different kinds of strings, dynamic, static,
relational/dynamic etc.
Now when a string field is used, the ":string" type can be used to display
it:
echo "e:sw sched/sched_switch comm=$next_comm:string" > dynamic_events
Link: https://lkml.kernel.org/r/20220820134400.959640191@goodmis.org
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tzvetomir Stoyanov <tz.stoyanov@gmail.com>
Cc: Tom Zanussi <zanussi@kernel.org>
Fixes: 7491e2c44278 ("tracing: Add a probe that attaches to trace events")
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef1e93d2eeb58a1f08c37b22a2314b94bc045f15 upstream.
bpf_iter_attach_map() acquires a map uref, and the uref may be released
before or in the middle of iterating map elements. For example, the uref
could be released in bpf_iter_detach_map() as part of
bpf_link_release(), or could be released in bpf_map_put_with_uref() as
part of bpf_map_release().
So acquiring an extra map uref in bpf_iter_init_hash_map() and
releasing it in bpf_iter_fini_hash_map().
Fixes: d6c4503cc296 ("bpf: Implement bpf iterator for hash maps")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/r/20220810080538.1845898-3-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f76fa6b338055054f80c72b29c97fb95c1becadc upstream.
bpf_iter_attach_map() acquires a map uref, and the uref may be released
before or in the middle of iterating map elements. For example, the uref
could be released in bpf_iter_detach_map() as part of
bpf_link_release(), or could be released in bpf_map_put_with_uref() as
part of bpf_map_release().
Alternative fix is acquiring an extra bpf_link reference just like
a pinned map iterator does, but it introduces unnecessary dependency
on bpf_link instead of bpf_map.
So choose another fix: acquiring an extra map uref in .init_seq_private
for array map iterator.
Fixes: d3cc2ab546ad ("bpf: Implement bpf iterator for array maps")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/r/20220810080538.1845898-2-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 275c30bcee66a27d1aa97a215d607ad6d49804cb upstream.
The LRU map that is preallocated may have its elements reused while
another program holds a pointer to it from bpf_map_lookup_elem. Hence,
only check_and_free_fields is appropriate when the element is being
deleted, as it ensures proper synchronization against concurrent access
of the map value. After that, we cannot call check_and_init_map_value
again as it may rewrite bpf_spin_lock, bpf_timer, and kptr fields while
they can be concurrently accessed from a BPF program.
This is safe to do as when the map entry is deleted, concurrent access
is protected against by check_and_free_fields, i.e. an existing timer
would be freed, and any existing kptr will be released by it. The
program can create further timers and kptrs after check_and_free_fields,
but they will eventually be released once the preallocated items are
freed on map destruction, even if the item is never reused again. Hence,
the deleted item sitting in the free list can still have resources
attached to it, and they would never leak.
With spin_lock, we never touch the field at all on delete or update, as
we may end up modifying the state of the lock. Since the verifier
ensures that a bpf_spin_lock call is always paired with bpf_spin_unlock
call, the program will eventually release the lock so that on reuse the
new user of the value can take the lock.
Essentially, for the preallocated case, we must assume that the map
value may always be in use by the program, even when it is sitting in
the freelist, and handle things accordingly, i.e. use proper
synchronization inside check_and_free_fields, and never reinitialize the
special fields when it is reused on update.
Fixes: 68134668c17f ("bpf: Add map side support for bpf timers.")
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/r/20220809213033.24147-3-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b2380577d4fe1c0ef3fa50417f1e441c016e4cbe upstream.
Make filtering consistent with histograms. As "cpu" can be a field of an
event, allow for "common_cpu" to keep it from being confused with the
"cpu" field of the event.
Link: https://lkml.kernel.org/r/20220820134401.513062765@goodmis.org
Link: https://lore.kernel.org/all/20220820220920.e42fa32b70505b1904f0a0ad@kernel.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tzvetomir Stoyanov <tz.stoyanov@gmail.com>
Cc: Tom Zanussi <zanussi@kernel.org>
Fixes: 1e3bac71c5053 ("tracing/histogram: Rename "cpu" to "common_cpu"")
Suggested-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ab8384442ee512fc0fc72deeb036110843d0e7ff upstream.
Both $comm and $COMM can be used to get current->comm in eprobes and the
filtering and histogram logic. Make kprobes and uprobes consistent in this
regard and allow both $comm and $COMM as well. Currently kprobes and
uprobes only handle $comm, which is inconsistent with the other utilities,
and can be confusing to users.
Link: https://lkml.kernel.org/r/20220820134401.317014913@goodmis.org
Link: https://lore.kernel.org/all/20220820220442.776e1ddaf8836e82edb34d01@kernel.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tzvetomir Stoyanov <tz.stoyanov@gmail.com>
Cc: Tom Zanussi <zanussi@kernel.org>
Fixes: 533059281ee5 ("tracing: probeevent: Introduce new argument fetching code")
Suggested-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6a832ec3d680b3a4f4fad5752672827d71bae501 upstream.
Currently, if a symbol "@" is attempted to be used with an event probe
(eprobes), it will cause a NULL pointer dereference crash.
Both kprobes and uprobes can reference data other than the main registers.
Such as immediate address, symbols and the current task name. Have eprobes
do the same thing.
For "comm", if "comm" is used and the event being attached to does not
have the "comm" field, then make it the "$comm" that kprobes has. This is
consistent to the way histograms and filters work.
Link: https://lkml.kernel.org/r/20220820134401.136924220@goodmis.org
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Tzvetomir Stoyanov <tz.stoyanov@gmail.com>
Cc: Tom Zanussi <zanussi@kernel.org>
Fixes: 7491e2c44278 ("tracing: Add a probe that attaches to trace events")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 02333de90e5945e2fe7fc75b15b4eb9aee187f0a upstream.
The variable $comm is hard coded as a string, which is true for both
kprobes and uprobes, but for event probes (eprobes) it is a field name. In
most cases the "comm" field would be a string, but there's no guarantee of
that fact.
Do not assume that comm is a string. Not to mention, it currently forces
comm fields to fault, as string processing for event probes is currently
broken.
Link: https://lkml.kernel.org/r/20220820134400.756152112@goodmis.org
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Tzvetomir Stoyanov <tz.stoyanov@gmail.com>
Cc: Tom Zanussi <zanussi@kernel.org>
Fixes: 7491e2c44278 ("tracing: Add a probe that attaches to trace events")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2673c60ee67e71f2ebe34386e62d348f71edee47 upstream.
While playing with event probes (eprobes), I tried to see what would
happen if I attempted to retrieve the instruction pointer (%rip) knowing
that event probes do not use pt_regs. The result was:
BUG: kernel NULL pointer dereference, address: 0000000000000024
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 1847 Comm: trace-cmd Not tainted 5.19.0-rc5-test+ #309
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01
v03.03 07/14/2016
RIP: 0010:get_event_field.isra.0+0x0/0x50
Code: ff 48 c7 c7 c0 8f 74 a1 e8 3d 8b f5 ff e8 88 09 f6 ff 4c 89 e7 e8
50 6a 13 00 48 89 ef 5b 5d 41 5c 41 5d e9 42 6a 13 00 66 90 <48> 63 47 24
8b 57 2c 48 01 c6 8b 47 28 83 f8 02 74 0e 83 f8 04 74
RSP: 0018:ffff916c394bbaf0 EFLAGS: 00010086
RAX: ffff916c854041d8 RBX: ffff916c8d9fbf50 RCX: ffff916c255d2000
RDX: 0000000000000000 RSI: ffff916c255d2008 RDI: 0000000000000000
RBP: 0000000000000000 R08: ffff916c3a2a0c08 R09: ffff916c394bbda8
R10: 0000000000000000 R11: 0000000000000000 R12: ffff916c854041d8
R13: ffff916c854041b0 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff916c9ea40000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000024 CR3: 000000011b60a002 CR4: 00000000001706e0
Call Trace:
<TASK>
get_eprobe_size+0xb4/0x640
? __mod_node_page_state+0x72/0xc0
__eprobe_trace_func+0x59/0x1a0
? __mod_lruvec_page_state+0xaa/0x1b0
? page_remove_file_rmap+0x14/0x230
? page_remove_rmap+0xda/0x170
event_triggers_call+0x52/0xe0
trace_event_buffer_commit+0x18f/0x240
trace_event_raw_event_sched_wakeup_template+0x7a/0xb0
try_to_wake_up+0x260/0x4c0
__wake_up_common+0x80/0x180
__wake_up_common_lock+0x7c/0xc0
do_notify_parent+0x1c9/0x2a0
exit_notify+0x1a9/0x220
do_exit+0x2ba/0x450
do_group_exit+0x2d/0x90
__x64_sys_exit_group+0x14/0x20
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Obviously this is not the desired result.
Move the testing for TPARG_FL_TPOINT which is only used for event probes
to the top of the "$" variable check, as all the other variables are not
used for event probes. Also add a check in the register parsing "%" to
fail if an event probe is used.
Link: https://lkml.kernel.org/r/20220820134400.564426983@goodmis.org
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tzvetomir Stoyanov <tz.stoyanov@gmail.com>
Cc: Tom Zanussi <zanussi@kernel.org>
Fixes: 7491e2c44278 ("tracing: Add a probe that attaches to trace events")
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7249921d94ff64f67b733eca0b68853a62032b3d upstream.
If in perf_trace_event_init(), the perf_trace_event_open() fails, then it
will call perf_trace_event_unreg() which will not only unregister the perf
trace event, but will also call the put() function of the tp_event.
The problem here is that the trace_event_try_get_ref() is called by the
caller of perf_trace_event_init() and if perf_trace_event_init() returns a
failure, it will then call trace_event_put(). But since the
perf_trace_event_unreg() already called the trace_event_put() function, it
triggers a WARN_ON().
WARNING: CPU: 1 PID: 30309 at kernel/trace/trace_dynevent.c:46 trace_event_dyn_put_ref+0x15/0x20
If perf_trace_event_reg() does not call the trace_event_try_get_ref() then
the perf_trace_event_unreg() should not be calling trace_event_put(). This
breaks symmetry and causes bugs like these.
Pull out the trace_event_put() from perf_trace_event_unreg() and call it
in the locations that perf_trace_event_unreg() is called. This not only
fixes this bug, but also brings back the proper symmetry of the reg/unreg
vs get/put logic.
Link: https://lore.kernel.org/all/cover.1660347763.git.kjlx@templeofstupid.com/
Link: https://lkml.kernel.org/r/20220816192817.43d5e17f@gandalf.local.home
Cc: stable@vger.kernel.org
Fixes: 1d18538e6a092 ("tracing: Have dynamic events have a ref counter")
Reported-by: Krister Johansen <kjlx@templeofstupid.com>
Reviewed-by: Krister Johansen <kjlx@templeofstupid.com>
Tested-by: Krister Johansen <kjlx@templeofstupid.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 55de2c0b5610cba5a5a93c0788031133c457e689 ]
Add '__rel_loc' using trace event macros. These macros are usually
not used in the kernel, except for testing purpose.
This also add "rel_" variant of macros for dynamic_array string,
and bitmask.
Link: https://lkml.kernel.org/r/163757342119.510314.816029622439099016.stgit@devnote2
Cc: Beau Belgrave <beaub@linux.microsoft.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9c9b26b0df270d4f9246e483a44686fca951a29c ]
The csdlock_debug kernel-boot parameter is parsed by the
early_param() function csdlock_debug(). If set, csdlock_debug()
invokes static_branch_enable() to enable csd_lock_wait feature, which
triggers a panic on arm64 for kernels built with CONFIG_SPARSEMEM=y and
CONFIG_SPARSEMEM_VMEMMAP=n.
With CONFIG_SPARSEMEM_VMEMMAP=n, __nr_to_section is called in
static_key_enable() and returns NULL, resulting in a NULL dereference
because mem_section is initialized only later in sparse_init().
This is also a problem for powerpc because early_param() functions
are invoked earlier than jump_label_init(), also resulting in
static_key_enable() failures. These failures cause the warning "static
key 'xxx' used before call to jump_label_init()".
Thus, early_param is too early for csd_lock_wait to run
static_branch_enable(), so changes it to __setup to fix these.
Fixes: 8d0968cc6b8f ("locking/csd_lock: Add boot parameter for controlling CSD lock debugging")
Cc: stable@vger.kernel.org
Reported-by: Chen jingwen <chenjingwen6@huawei.com>
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b8ac29b40183a6038919768b5d189c9bd91ce9b4 ]
The rng's random_init() function contributes the real time to the rng at
boot time, so that events can at least start in relation to something
particular in the real world. But this clock might not yet be set that
point in boot, so nothing is contributed. In addition, the relation
between minor clock changes from, say, NTP, and the cycle counter is
potentially useful entropic data.
This commit addresses this by mixing in a time stamp on calls to
settimeofday and adjtimex. No entropy is credited in doing so, so it
doesn't make initialization faster, but it is still useful input to
have.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 751d4cbc43879229dbc124afefe240b70fd29a85 ]
The following warning was triggered on a large machine early in boot on
a distribution kernel but the same problem should also affect mainline.
WARNING: CPU: 439 PID: 10 at ../kernel/workqueue.c:2231 process_one_work+0x4d/0x440
Call Trace:
<TASK>
rescuer_thread+0x1f6/0x360
kthread+0x156/0x180
ret_from_fork+0x22/0x30
</TASK>
Commit c6e7bd7afaeb ("sched/core: Optimize ttwu() spinning on p->on_cpu")
optimises ttwu by queueing a task that is descheduling on the wakelist,
but does not check if the task descheduling is still allowed to run on that CPU.
In this warning, the problematic task is a workqueue rescue thread which
checks if the rescue is for a per-cpu workqueue and running on the wrong CPU.
While this is early in boot and it should be possible to create workers,
the rescue thread may still used if the MAYDAY_INITIAL_TIMEOUT is reached
or MAYDAY_INTERVAL and on a sufficiently large machine, the rescue
thread is being used frequently.
Tracing confirmed that the task should have migrated properly using the
stopper thread to handle the migration. However, a parallel wakeup from udev
running on another CPU that does not share CPU cache observes p->on_cpu and
uses task_cpu(p), queues the task on the old CPU and triggers the warning.
Check that the wakee task that is descheduling is still allowed to run
on its current CPU and if not, wait for the descheduling to complete
and select an allowed CPU.
Fixes: c6e7bd7afaeb ("sched/core: Optimize ttwu() spinning on p->on_cpu")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20220804092119.20137-1-mgorman@techsingularity.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3dd3f674555bd9455c5ae7fafce0696bd9931b3 ]
Wakelist can help avoid cache bouncing and offload the overhead of waker
cpu. So far, using wakelist within the same llc only happens on
WF_ON_CPU, and this limitation could be removed to further improve
wakeup performance.
The commit 518cd6234178 ("sched: Only queue remote wakeups when
crossing cache boundaries") disabled queuing tasks on wakelist when
the cpus share llc. This is because, at that time, the scheduler must
send IPIs to do ttwu_queue_wakelist. Nowadays, ttwu_queue_wakelist also
supports TIF_POLLING, so this is not a problem now when the wakee cpu is
in idle polling.
Benefits:
Queuing the task on idle cpu can help improving performance on waker cpu
and utilization on wakee cpu, and further improve locality because
the wakee cpu can handle its own rq. This patch helps improving rt on
our real java workloads where wakeup happens frequently.
Consider the normal condition (CPU0 and CPU1 share same llc)
Before this patch:
CPU0 CPU1
select_task_rq() idle
rq_lock(CPU1->rq)
enqueue_task(CPU1->rq)
notify CPU1 (by sending IPI or CPU1 polling)
resched()
After this patch:
CPU0 CPU1
select_task_rq() idle
add to wakelist of CPU1
notify CPU1 (by sending IPI or CPU1 polling)
rq_lock(CPU1->rq)
enqueue_task(CPU1->rq)
resched()
We see CPU0 can finish its work earlier. It only needs to put task to
wakelist and return.
While CPU1 is idle, so let itself handle its own runqueue data.
This patch brings no difference about IPI.
This patch only takes effect when the wakee cpu is:
1) idle polling
2) idle not polling
For 1), there will be no IPI with or without this patch.
For 2), there will always be an IPI before or after this patch.
Before this patch: waker cpu will enqueue task and check preempt. Since
"idle" will be sure to be preempted, waker cpu must send a resched IPI.
After this patch: waker cpu will put the task to the wakelist of wakee
cpu, and send an IPI.
Benchmark:
We've tested schbench, unixbench, and hachbench on both x86 and arm64.
On x86 (Intel Xeon Platinum 8269CY):
schbench -m 2 -t 8
Latency percentiles (usec) before after
50.0000th: 8 6
75.0000th: 10 7
90.0000th: 11 8
95.0000th: 12 8
*99.0000th: 13 10
99.5000th: 15 11
99.9000th: 18 14
Unixbench with full threads (104)
before after
Dhrystone 2 using register variables 3011862938 3009935994 -0.06%
Double-Precision Whetstone 617119.3 617298.5 0.03%
Execl Throughput 27667.3 27627.3 -0.14%
File Copy 1024 bufsize 2000 maxblocks 785871.4 784906.2 -0.12%
File Copy 256 bufsize 500 maxblocks 210113.6 212635.4 1.20%
File Copy 4096 bufsize 8000 maxblocks 2328862.2 2320529.1 -0.36%
Pipe Throughput 145535622.8 145323033.2 -0.15%
Pipe-based Context Switching 3221686.4 3583975.4 11.25%
Process Creation 101347.1 103345.4 1.97%
Shell Scripts (1 concurrent) 120193.5 123977.8 3.15%
Shell Scripts (8 concurrent) 17233.4 17138.4 -0.55%
System Call Overhead 5300604.8 5312213.6 0.22%
hackbench -g 1 -l 100000
before after
Time 3.246 2.251
On arm64 (Ampere Altra):
schbench -m 2 -t 8
Latency percentiles (usec) before after
50.0000th: 14 10
75.0000th: 19 14
90.0000th: 22 16
95.0000th: 23 16
*99.0000th: 24 17
99.5000th: 24 17
99.9000th: 28 25
Unixbench with full threads (80)
before after
Dhrystone 2 using register variables 3536194249 3537019613 0.02%
Double-Precision Whetstone 629383.6 629431.6 0.01%
Execl Throughput 65920.5 65846.2 -0.11%
File Copy 1024 bufsize 2000 maxblocks 1063722.8 1064026.8 0.03%
File Copy 256 bufsize 500 maxblocks 322684.5 318724.5 -1.23%
File Copy 4096 bufsize 8000 maxblocks 2348285.3 2328804.8 -0.83%
Pipe Throughput 133542875.3 131619389.8 -1.44%
Pipe-based Context Switching 3215356.1 3576945.1 11.25%
Process Creation 108520.5 120184.6 10.75%
Shell Scripts (1 concurrent) 122636.3 121888 -0.61%
Shell Scripts (8 concurrent) 17462.1 17381.4 -0.46%
System Call Overhead 4429998.9 4435006.7 0.11%
hackbench -g 1 -l 100000
before after
Time 4.217 2.916
Our patch has improvement on schbench, hackbench
and Pipe-based Context Switching of unixbench
when there exists idle cpus,
and no obvious regression on other tests of unixbench.
This can help improve rt in scenes where wakeup happens frequently.
Signed-off-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Link: https://lore.kernel.org/r/20220608233412.327341-3-dtcccc@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 28156108fecb1f808b21d216e8ea8f0d205a530c ]
The commit 2ebb17717550 ("sched/core: Offload wakee task activation if it
the wakee is descheduling") checked rq->nr_running <= 1 to avoid task
stacking when WF_ON_CPU.
Per the ordering of writes to p->on_rq and p->on_cpu, observing p->on_cpu
(WF_ON_CPU) in ttwu_queue_cond() implies !p->on_rq, IOW p has gone through
the deactivate_task() in __schedule(), thus p has been accounted out of
rq->nr_running. As such, the task being the only runnable task on the rq
implies reading rq->nr_running == 0 at that point.
The benchmark result is in [1].
[1] https://lore.kernel.org/all/e34de686-4e85-bde1-9f3c-9bbc86b38627@linux.alibaba.com/
Suggested-by: Valentin Schneider <vschneid@redhat.com>
Signed-off-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Link: https://lore.kernel.org/r/20220608233412.327341-2-dtcccc@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6e8d40d43ae4dec00c8fea2593eeea3114b8f44 ]
With cgroup v2, the cpuset's cpus_allowed mask can be empty indicating
that the cpuset will just use the effective CPUs of its parent. So
cpuset_can_attach() can call task_can_attach() with an empty mask.
This can lead to cpumask_any_and() returns nr_cpu_ids causing the call
to dl_bw_of() to crash due to percpu value access of an out of bound
CPU value. For example:
[80468.182258] BUG: unable to handle page fault for address: ffffffff8b6648b0
:
[80468.191019] RIP: 0010:dl_cpu_busy+0x30/0x2b0
:
[80468.207946] Call Trace:
[80468.208947] cpuset_can_attach+0xa0/0x140
[80468.209953] cgroup_migrate_execute+0x8c/0x490
[80468.210931] cgroup_update_dfl_csses+0x254/0x270
[80468.211898] cgroup_subtree_control_write+0x322/0x400
[80468.212854] kernfs_fop_write_iter+0x11c/0x1b0
[80468.213777] new_sync_write+0x11f/0x1b0
[80468.214689] vfs_write+0x1eb/0x280
[80468.215592] ksys_write+0x5f/0xe0
[80468.216463] do_syscall_64+0x5c/0x80
[80468.224287] entry_SYSCALL_64_after_hwframe+0x44/0xae
Fix that by using effective_cpus instead. For cgroup v1, effective_cpus
is the same as cpus_allowed. For v2, effective_cpus is the real cpumask
to be used by tasks within the cpuset anyway.
Also update task_can_attach()'s 2nd argument name to cs_effective_cpus to
reflect the change. In addition, a check is added to task_can_attach()
to guard against the possibility that cpumask_any_and() may return a
value >= nr_cpu_ids.
Fixes: 7f51412a415d ("sched/deadline: Fix bandwidth check/update when migrating tasks between exclusive cpusets")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lore.kernel.org/r/20220803015451.2219567-1-longman@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 772b6539fdda31462cc08368e78df60b31a58bab ]
Both functions are doing almost the same, that is checking if admission
control is still respected.
With exclusive cpusets, dl_task_can_attach() checks if the destination
cpuset (i.e. its root domain) has enough CPU capacity to accommodate the
task.
dl_cpu_busy() checks if there is enough CPU capacity in the cpuset in
case the CPU is hot-plugged out.
dl_task_can_attach() is used to check if a task can be admitted while
dl_cpu_busy() is used to check if a CPU can be hotplugged out.
Make dl_cpu_busy() able to deal with a task and use it instead of
dl_task_can_attach() in task_can_attach().
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lore.kernel.org/r/20220302183433.333029-4-dietmar.eggemann@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 28f6c37a2910f565b4f5960df52b2eccae28c891 ]
kernel_text_address() treats ftrace_trampoline, kprobe_insn_slot
and bpf_text_address as valid kprobe addresses - which is not ideal.
These text areas are removable and changeable without any notification
to kprobes, and probing on them can trigger unexpected behavior:
https://lkml.org/lkml/2022/7/26/1148
Considering that jump_label and static_call text are already
forbiden to probe, kernel_text_address() should be replaced with
core_kernel_text() and is_module_text_address() to check other text
areas which are unsafe to kprobe.
[ mingo: Rewrote the changelog. ]
Fixes: 5b485629ba0d ("kprobes, extable: Identify kprobes trampolines as kernel text area")
Fixes: 74451e66d516 ("bpf: make jited programs visible in traces")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20220801033719.228248-1-chenzhongjin@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c51ba246cb172c9e947dc6fb8868a1eaf0b2a913 ]
In the failure case of trying to use a buffer which we'd previously
failed to allocate, the "!mem" condition is no longer sufficient since
io_tlb_default_mem became static and assigned by default. Update the
condition to work as intended per the rest of that conversion.
Fixes: 463e862ac63e ("swiotlb: Convert io_default_tlb_mem to static allocation")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0fe6ee8f123a4dfb529a5aff07536bb481f34043 ]
2d186afd04d6 ("profiling: fix shift-out-of-bounds bugs") limits shift
value by [0, BITS_PER_LONG -1], which means [0, 63].
However, syzbot found that the max shift value should be the bit number of
(_etext - _stext). If shift is outside of this, the "buffer_bytes" will
be zero and will cause kzalloc(0). Then the kernel panics due to
dereferencing the returned pointer 16.
This can be easily reproduced by passing a large number like 60 to enable
profiling and then run readprofile.
LOGS:
BUG: kernel NULL pointer dereference, address: 0000000000000010
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 6148067 P4D 6148067 PUD 6142067 PMD 0
PREEMPT SMP
CPU: 4 PID: 184 Comm: readprofile Not tainted 5.18.0+ #162
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
RIP: 0010:read_profile+0x104/0x220
RSP: 0018:ffffc900006fbe80 EFLAGS: 00000202
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff888006150000 RSI: 0000000000000001 RDI: ffffffff82aba4a0
RBP: 000000000188bb60 R08: 0000000000000010 R09: ffff888006151000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff82aba4a0
R13: 0000000000000000 R14: ffffc900006fbf08 R15: 0000000000020c30
FS: 000000000188a8c0(0000) GS:ffff88803ed00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000010 CR3: 0000000006144000 CR4: 00000000000006e0
Call Trace:
<TASK>
proc_reg_read+0x56/0x70
vfs_read+0x9a/0x1b0
ksys_read+0xa1/0xe0
? fpregs_assert_state_consistent+0x1e/0x40
do_syscall_64+0x3a/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x4d4b4e
RSP: 002b:00007ffebb668d58 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
RAX: ffffffffffffffda RBX: 000000000188a8a0 RCX: 00000000004d4b4e
RDX: 0000000000000400 RSI: 000000000188bb60 RDI: 0000000000000003
RBP: 0000000000000003 R08: 000000000000006e R09: 0000000000000000
R10: 0000000000000041 R11: 0000000000000246 R12: 000000000188bb60
R13: 0000000000000400 R14: 0000000000000000 R15: 000000000188bb60
</TASK>
Modules linked in:
CR2: 0000000000000010
Killed
---[ end trace 0000000000000000 ]---
Check prof_len in profile_init() to prevent it be zero.
Link: https://lkml.kernel.org/r/20220531012854.229439-1-chenzhongjin@huawei.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 151c8e499f4705010780189377f85b57400ccbf5 ]
Using msleep() is problematic because it's compared against
ratelimiter.c's ktime_get_coarse_boottime_ns(), which means on systems
with slow jiffies (such as UML's forced HZ=100), the result is
inaccurate. So switch to using schedule_hrtimeout().
However, hrtimer gives us access only to the traditional posix timers,
and none of the _COARSE variants. So now, rather than being too
imprecise like jiffies, it's too precise.
One solution would be to give it a large "range" value, but this will
still fire early on a loaded system. A better solution is to align the
timeout to the actual coarse timer, and then round up to the nearest
tick, plus change.
So add the timeout to the current coarse time, and then
schedule_hrtimer() until the absolute computed time.
This should hopefully reduce flakes in CI as well. Note that we keep the
retry loop in case the entire function is running behind, because the
test could still be scheduled out, by either the kernel or by the
hypervisor's kernel, in which case restarting the test and hoping to not
be scheduled out still helps.
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9c7c48d6a1e2eb5192ad5294c1c4dbd42a88e88b ]
The commit 7337224fc150 ("bpf: Improve the info.func_info and info.func_info_rec_size behavior")
accidently made bpf_prog_ksym_set_name() conservative for bpf subprograms.
Fixed it so instead of "bpf_prog_tag_F" the stack traces print "bpf_prog_tag_full_subprog_name".
Fixes: 7337224fc150 ("bpf: Improve the info.func_info and info.func_info_rec_size behavior")
Reported-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20220714211637.17150-1-alexei.starovoitov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3002153a91a9732a6d1d0bb95138593c7da15743 ]
The RCU priority boosting can fail in two situations:
1) If (nr_cpus= > maxcpus=), which means if the total number of CPUs
is higher than those brought online at boot, then torture_onoff() may
later bring up CPUs that weren't online on boot. Now since rcutorture
initialization only boosts the ksoftirqds of the CPUs that have been
set online on boot, the CPUs later set online by torture_onoff won't
benefit from the boost, making RCU priority boosting fail.
2) The ksoftirqd kthreads are boosted after the creation of
rcu_torture_boost() kthreads, which opens a window large enough for these
rcu_torture_boost() kthreads to wait (despite running at FIFO priority)
for ksoftirqds that are still running at SCHED_NORMAL priority.
The issues can trigger for example with:
./kvm.sh --configs TREE01 --kconfig "CONFIG_RCU_BOOST=y"
[ 34.968561] rcu-torture: !!!
[ 34.968627] ------------[ cut here ]------------
[ 35.014054] WARNING: CPU: 4 PID: 114 at kernel/rcu/rcutorture.c:1979 rcu_torture_stats_print+0x5ad/0x610
[ 35.052043] Modules linked in:
[ 35.069138] CPU: 4 PID: 114 Comm: rcu_torture_sta Not tainted 5.18.0-rc1 #1
[ 35.096424] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.14.0-0-g155821a-rebuilt.opensuse.org 04/01/2014
[ 35.154570] RIP: 0010:rcu_torture_stats_print+0x5ad/0x610
[ 35.198527] Code: 63 1b 02 00 74 02 0f 0b 48 83 3d 35 63 1b 02 00 74 02 0f 0b 48 83 3d 21 63 1b 02 00 74 02 0f 0b 48 83 3d 0d 63 1b 02 00 74 02 <0f> 0b 83 eb 01 0f 8e ba fc ff ff 0f 0b e9 b3 fc ff f82
[ 37.251049] RSP: 0000:ffffa92a0050bdf8 EFLAGS: 00010202
[ 37.277320] rcu: De-offloading 8
[ 37.290367] RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000001
[ 37.290387] RDX: 0000000000000000 RSI: 00000000ffffbfff RDI: 00000000ffffffff
[ 37.290398] RBP: 000000000000007b R08: 0000000000000000 R09: c0000000ffffbfff
[ 37.290407] R10: 000000000000002a R11: ffffa92a0050bc18 R12: ffffa92a0050be20
[ 37.290417] R13: ffffa92a0050be78 R14: 0000000000000000 R15: 000000000001bea0
[ 37.290427] FS: 0000000000000000(0000) GS:ffff96045eb00000(0000) knlGS:0000000000000000
[ 37.290448] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 37.290460] CR2: 0000000000000000 CR3: 000000001dc0c000 CR4: 00000000000006e0
[ 37.290470] Call Trace:
[ 37.295049] <TASK>
[ 37.295065] ? preempt_count_add+0x63/0x90
[ 37.295095] ? _raw_spin_lock_irqsave+0x12/0x40
[ 37.295125] ? rcu_torture_stats_print+0x610/0x610
[ 37.295143] rcu_torture_stats+0x29/0x70
[ 37.295160] kthread+0xe3/0x110
[ 37.295176] ? kthread_complete_and_exit+0x20/0x20
[ 37.295193] ret_from_fork+0x22/0x30
[ 37.295218] </TASK>
Fix this with boosting the ksoftirqds kthreads from the boosting
hotplug callback itself and before the boosting kthreads are created.
Fixes: ea6d962e80b6 ("rcutorture: Judge RCU priority boosting on grace periods, not callbacks")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd13fe16db0d82612b260640f4e26f6d9d1e11fd ]
Currently, in CONFIG_RCU_BOOST kernels, if the rcu_torture_init()
function's call to cpuhp_setup_state() fails, rcu_torture_cleanup()
gamely passes nonsense to cpuhp_remove_state(). This results in
strange and misleading splats. This commit therefore ensures that if
the rcu_torture_init() function's call to cpuhp_setup_state() fails,
rcu_torture_cleanup() avoids invoking cpuhp_remove_state().
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit efeff6b39b9de4480572c7b0c5eb77204795cb57 ]
When running rcutorture as a module, any rcu_torture_init() issues will be
reflected in the error code from modprobe or insmod, as the case may be.
However, these error codes are not available when running rcutorture
built-in, for example, when using the kvm.sh script. This commit
therefore adds WARN_ON_ONCE() to allow distinguishing rcu_torture_init()
errors when running rcutorture built-in.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5c66d1b9b30f737fcef85a0b75bfe0590e16b62a ]
dequeue_task_rt() only decrements 'rt_rq->rt_nr_running' after having
called sched_update_tick_dependency() preventing it from re-enabling the
tick on systems that no longer have pending SCHED_RT tasks but have
multiple runnable SCHED_OTHER tasks:
dequeue_task_rt()
dequeue_rt_entity()
dequeue_rt_stack()
dequeue_top_rt_rq()
sub_nr_running() // decrements rq->nr_running
sched_update_tick_dependency()
sched_can_stop_tick() // checks rq->rt.rt_nr_running,
...
__dequeue_rt_entity()
dec_rt_tasks() // decrements rq->rt.rt_nr_running
...
Every other scheduler class performs the operation in the opposite
order, and sched_update_tick_dependency() expects the values to be
updated as such. So avoid the misbehaviour by inverting the order in
which the above operations are performed in the RT scheduler.
Fixes: 76d92ac305f2 ("sched: Migrate sched to use new tick dependency mask model")
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Reviewed-by: Phil Auld <pauld@redhat.com>
Link: https://lore.kernel.org/r/20220628092259.330171-1-nsaenzju@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6f194c99f466147148cc08452718b46664112548 ]
When using a NOMAP domain, __irq_resolve_mapping() doesn't store
the Linux IRQ number at the address optionally provided by the caller.
While this isn't a huge deal (the returned value is guaranteed
to the hwirq that was passed as a parameter), let's honour the letter
of the API by writing the expected value.
Fixes: d22558dd0a6c (“irqdomain: Introduce irq_resolve_mapping()”)
Signed-off-by: Xu Qiang <xuqiang36@huawei.com>
[maz: commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220719063641.56541-2-xuqiang36@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 22c80aac882f712897b88b7ea8f5a74ea19019df ]
Trace the remapped operation and its flags instead of only the data
direction of remapped operations. This issue was detected by analyzing
the warnings reported by sparse related to the new blk_opf_t type.
Reviewed-by: Jun'ichi Nomura <junichi.nomura@nec.com>
Cc: Mike Snitzer <snitzer@kernel.org>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Fixes: 1b9a9ab78b0a ("blktrace: use op accessors")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-11-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eae6d58d67d9739be5f7ae2dbead1d0ef6528243 ]
Commit dfd5e3f5fe27 ("locking/lockdep: Mark local_lock_t") added yet
another lockdep_init_map_*() variant, but forgot to update all the
existing users of the most complicated version.
This could lead to a loss of lock_type and hence an incorrect report.
Given the relative rarity of both local_lock and these annotations,
this is unlikely to happen in practise, still, best fix things.
Fixes: dfd5e3f5fe27 ("locking/lockdep: Mark local_lock_t")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/YqyEDtoan20K0CVD@worktop.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8386c414e27caba8501119948e9551e52b527f59 ]
syzbot is reporting hung task at misc_open() [1], for there is a race
window of AB-BA deadlock which involves probe_count variable. Currently
wait_for_device_probe() from snapshot_open() from misc_open() can sleep
forever with misc_mtx held if probe_count cannot become 0.
When a device is probed by hub_event() work function, probe_count is
incremented before the probe function starts, and probe_count is
decremented after the probe function completed.
There are three cases that can prevent probe_count from dropping to 0.
(a) A device being probed stopped responding (i.e. broken/malicious
hardware).
(b) A process emulating a USB device using /dev/raw-gadget interface
stopped responding for some reason.
(c) New device probe requests keeps coming in before existing device
probe requests complete.
The phenomenon syzbot is reporting is (b). A process which is holding
system_transition_mutex and misc_mtx is waiting for probe_count to become
0 inside wait_for_device_probe(), but the probe function which is called
from hub_event() work function is waiting for the processes which are
blocked at mutex_lock(&misc_mtx) to respond via /dev/raw-gadget interface.
This patch mitigates (b) by deferring wait_for_device_probe() from
snapshot_open() to snapshot_write() and snapshot_ioctl(). Please note that
the possibility of (b) remains as long as any thread which is emulating a
USB device via /dev/raw-gadget interface can be blocked by uninterruptible
blocking operations (e.g. mutex_lock()).
Please also note that (a) and (c) are not addressed. Regarding (c), we
should change the code to wait for only one device which contains the
image for resuming from hibernation. I don't know how to address (a), for
use of timeout for wait_for_device_probe() might result in loss of user
data in the image. Maybe we should require the userland to wait for the
image device before opening /dev/snapshot interface.
Link: https://syzkaller.appspot.com/bug?extid=358c9ab4c93da7b7238c [1]
Reported-by: syzbot <syzbot+358c9ab4c93da7b7238c@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+358c9ab4c93da7b7238c@syzkaller.appspotmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 401e4963bf45c800e3e9ea0d3a0289d738005fd4 ]
With CONFIG_PREEMPT_RT, it is possible to hit a deadlock between two
normal priority tasks (SCHED_OTHER, nice level zero):
INFO: task kworker/u8:0:8 blocked for more than 491 seconds.
Not tainted 5.15.49-rt46 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u8:0 state:D stack: 0 pid: 8 ppid: 2 flags:0x00000000
Workqueue: writeback wb_workfn (flush-7:0)
[<c08a3a10>] (__schedule) from [<c08a3d84>] (schedule+0xdc/0x134)
[<c08a3d84>] (schedule) from [<c08a65a0>] (rt_mutex_slowlock_block.constprop.0+0xb8/0x174)
[<c08a65a0>] (rt_mutex_slowlock_block.constprop.0) from [<c08a6708>]
+(rt_mutex_slowlock.constprop.0+0xac/0x174)
[<c08a6708>] (rt_mutex_slowlock.constprop.0) from [<c0374d60>] (fat_write_inode+0x34/0x54)
[<c0374d60>] (fat_write_inode) from [<c0297304>] (__writeback_single_inode+0x354/0x3ec)
[<c0297304>] (__writeback_single_inode) from [<c0297998>] (writeback_sb_inodes+0x250/0x45c)
[<c0297998>] (writeback_sb_inodes) from [<c0297c20>] (__writeback_inodes_wb+0x7c/0xb8)
[<c0297c20>] (__writeback_inodes_wb) from [<c0297f24>] (wb_writeback+0x2c8/0x2e4)
[<c0297f24>] (wb_writeback) from [<c0298c40>] (wb_workfn+0x1a4/0x3e4)
[<c0298c40>] (wb_workfn) from [<c0138ab8>] (process_one_work+0x1fc/0x32c)
[<c0138ab8>] (process_one_work) from [<c0139120>] (worker_thread+0x22c/0x2d8)
[<c0139120>] (worker_thread) from [<c013e6e0>] (kthread+0x16c/0x178)
[<c013e6e0>] (kthread) from [<c01000fc>] (ret_from_fork+0x14/0x38)
Exception stack(0xc10e3fb0 to 0xc10e3ff8)
3fa0: 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
INFO: task tar:2083 blocked for more than 491 seconds.
Not tainted 5.15.49-rt46 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:tar state:D stack: 0 pid: 2083 ppid: 2082 flags:0x00000000
[<c08a3a10>] (__schedule) from [<c08a3d84>] (schedule+0xdc/0x134)
[<c08a3d84>] (schedule) from [<c08a41b0>] (io_schedule+0x14/0x24)
[<c08a41b0>] (io_schedule) from [<c08a455c>] (bit_wait_io+0xc/0x30)
[<c08a455c>] (bit_wait_io) from [<c08a441c>] (__wait_on_bit_lock+0x54/0xa8)
[<c08a441c>] (__wait_on_bit_lock) from [<c08a44f4>] (out_of_line_wait_on_bit_lock+0x84/0xb0)
[<c08a44f4>] (out_of_line_wait_on_bit_lock) from [<c0371fb0>] (fat_mirror_bhs+0xa0/0x144)
[<c0371fb0>] (fat_mirror_bhs) from [<c0372a68>] (fat_alloc_clusters+0x138/0x2a4)
[<c0372a68>] (fat_alloc_clusters) from [<c0370b14>] (fat_alloc_new_dir+0x34/0x250)
[<c0370b14>] (fat_alloc_new_dir) from [<c03787c0>] (vfat_mkdir+0x58/0x148)
[<c03787c0>] (vfat_mkdir) from [<c0277b60>] (vfs_mkdir+0x68/0x98)
[<c0277b60>] (vfs_mkdir) from [<c027b484>] (do_mkdirat+0xb0/0xec)
[<c027b484>] (do_mkdirat) from [<c0100060>] (ret_fast_syscall+0x0/0x1c)
Exception stack(0xc2e1bfa8 to 0xc2e1bff0)
bfa0: 01ee42f0 01ee4208 01ee42f0 000041ed 00000000 00004000
bfc0: 01ee42f0 01ee4208 00000000 00000027 01ee4302 00000004 000dcb00 01ee4190
bfe0: 000dc368 bed11924 0006d4b0 b6ebddfc
Here the kworker is waiting on msdos_sb_info::s_lock which is held by
tar which is in turn waiting for a buffer which is locked waiting to be
flushed, but this operation is plugged in the kworker.
The lock is a normal struct mutex, so tsk_is_pi_blocked() will always
return false on !RT and thus the behaviour changes for RT.
It seems that the intent here is to skip blk_flush_plug() in the case
where a non-preemptible lock (such as a spinlock) has been converted to
a rtmutex on RT, which is the case covered by the SM_RTLOCK_WAIT
schedule flag. But sched_submit_work() is only called from schedule()
which is never called in this scenario, so the check can simply be
deleted.
Looking at the history of the -rt patchset, in fact this change was
present from v5.9.1-rt20 until being dropped in v5.13-rt1 as it was part
of a larger patch [1] most of which was replaced by commit b4bfa3fcfe3b
("sched/core: Rework the __schedule() preempt argument").
As described in [1]:
The schedule process must distinguish between blocking on a regular
sleeping lock (rwsem and mutex) and a RT-only sleeping lock (spinlock
and rwlock):
- rwsem and mutex must flush block requests (blk_schedule_flush_plug())
even if blocked on a lock. This can not deadlock because this also
happens for non-RT.
There should be a warning if the scheduling point is within a RCU read
section.
- spinlock and rwlock must not flush block requests. This will deadlock
if the callback attempts to acquire a lock which is already acquired.
Similarly to being preempted, there should be no warning if the
scheduling point is within a RCU read section.
and with the tsk_is_pi_blocked() in the scheduler path, we hit the first
issue.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git/tree/patches/0022-locking-rtmutex-Use-custom-scheduling-function-for-s.patch?h=linux-5.10.y-rt-patches
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lkml.kernel.org/r/20220708162702.1758865-1-john@metanate.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0f5209fee90b4544c58b4278d944425292789967 ]
The generic IPI code depends on the IRQ affinity mask being allocated
and initialized. This will not be the case if SMP is disabled. Fix up
the remaining driver that selected GENERIC_IRQ_IPI in a non-SMP config.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220701200056.46555-3-samuel@sholland.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 95001b756467ecc9f5973eb5e74e97699d9bbdf1 ]
Function irq_chip::irq_request_resources() is reported as optional
in the declaration of struct irq_chip.
If the parent irq_chip does not implement it, we should ignore it
and return.
Don't return error if the functions is missing.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220512160544.13561-1-antonio.borneo@foss.st.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70fb5ccf2ebb09a0c8ebba775041567812d45f86 ]
[Problem Statement]
select_idle_cpu() might spend too much time searching for an idle CPU,
when the system is overloaded.
The following histogram is the time spent in select_idle_cpu(),
when running 224 instances of netperf on a system with 112 CPUs
per LLC domain:
@usecs:
[0] 533 | |
[1] 5495 | |
[2, 4) 12008 | |
[4, 8) 239252 | |
[8, 16) 4041924 |@@@@@@@@@@@@@@ |
[16, 32) 12357398 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[32, 64) 14820255 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@|
[64, 128) 13047682 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[128, 256) 8235013 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[256, 512) 4507667 |@@@@@@@@@@@@@@@ |
[512, 1K) 2600472 |@@@@@@@@@ |
[1K, 2K) 927912 |@@@ |
[2K, 4K) 218720 | |
[4K, 8K) 98161 | |
[8K, 16K) 37722 | |
[16K, 32K) 6715 | |
[32K, 64K) 477 | |
[64K, 128K) 7 | |
netperf latency usecs:
=======
case load Lat_99th std%
TCP_RR thread-224 257.39 ( 0.21)
The time spent in select_idle_cpu() is visible to netperf and might have a negative
impact.
[Symptom analysis]
The patch [1] from Mel Gorman has been applied to track the efficiency
of select_idle_sibling. Copy the indicators here:
SIS Search Efficiency(se_eff%):
A ratio expressed as a percentage of runqueues scanned versus
idle CPUs found. A 100% efficiency indicates that the target,
prev or recent CPU of a task was idle at wakeup. The lower the
efficiency, the more runqueues were scanned before an idle CPU
was found.
SIS Domain Search Efficiency(dom_eff%):
Similar, except only for the slower SIS
patch.
SIS Fast Success Rate(fast_rate%):
Percentage of SIS that used target, prev or
recent CPUs.
SIS Success rate(success_rate%):
Percentage of scans that found an idle CPU.
The test is based on Aubrey's schedtests tool, including netperf, hackbench,
schbench and tbench.
Test on vanilla kernel:
schedstat_parse.py -f netperf_vanilla.log
case load se_eff% dom_eff% fast_rate% success_rate%
TCP_RR 28 threads 99.978 18.535 99.995 100.000
TCP_RR 56 threads 99.397 5.671 99.964 100.000
TCP_RR 84 threads 21.721 6.818 73.632 100.000
TCP_RR 112 threads 12.500 5.533 59.000 100.000
TCP_RR 140 threads 8.524 4.535 49.020 100.000
TCP_RR 168 threads 6.438 3.945 40.309 99.999
TCP_RR 196 threads 5.397 3.718 32.320 99.982
TCP_RR 224 threads 4.874 3.661 25.775 99.767
UDP_RR 28 threads 99.988 17.704 99.997 100.000
UDP_RR 56 threads 99.528 5.977 99.970 100.000
UDP_RR 84 threads 24.219 6.992 76.479 100.000
UDP_RR 112 threads 13.907 5.706 62.538 100.000
UDP_RR 140 threads 9.408 4.699 52.519 100.000
UDP_RR 168 threads 7.095 4.077 44.352 100.000
UDP_RR 196 threads 5.757 3.775 35.764 99.991
UDP_RR 224 threads 5.124 3.704 28.748 99.860
schedstat_parse.py -f schbench_vanilla.log
(each group has 28 tasks)
case load se_eff% dom_eff% fast_rate% success_rate%
normal 1 mthread 99.152 6.400 99.941 100.000
normal 2 mthreads 97.844 4.003 99.908 100.000
normal 3 mthreads 96.395 2.118 99.917 99.998
normal 4 mthreads 55.288 1.451 98.615 99.804
normal 5 mthreads 7.004 1.870 45.597 61.036
normal 6 mthreads 3.354 1.346 20.777 34.230
normal 7 mthreads 2.183 1.028 11.257 21.055
normal 8 mthreads 1.653 0.825 7.849 15.549
schedstat_parse.py -f hackbench_vanilla.log
(each group has 28 tasks)
case load se_eff% dom_eff% fast_rate% success_rate%
process-pipe 1 group 99.991 7.692 99.999 100.000
process-pipe 2 groups 99.934 4.615 99.997 100.000
process-pipe 3 groups 99.597 3.198 99.987 100.000
process-pipe 4 groups 98.378 2.464 99.958 100.000
process-pipe 5 groups 27.474 3.653 89.811 99.800
process-pipe 6 groups 20.201 4.098 82.763 99.570
process-pipe 7 groups 16.423 4.156 77.398 99.316
process-pipe 8 groups 13.165 3.920 72.232 98.828
process-sockets 1 group 99.977 5.882 99.999 100.000
process-sockets 2 groups 99.927 5.505 99.996 100.000
process-sockets 3 groups 99.397 3.250 99.980 100.000
process-sockets 4 groups 79.680 4.258 98.864 99.998
process-sockets 5 groups 7.673 2.503 63.659 92.115
process-sockets 6 groups 4.642 1.584 58.946 88.048
process-sockets 7 groups 3.493 1.379 49.816 81.164
process-sockets 8 groups 3.015 1.407 40.845 75.500
threads-pipe 1 group 99.997 0.000 100.000 100.000
threads-pipe 2 groups 99.894 2.932 99.997 100.000
threads-pipe 3 groups 99.611 4.117 99.983 100.000
threads-pipe 4 groups 97.703 2.624 99.937 100.000
threads-pipe 5 groups 22.919 3.623 87.150 99.764
threads-pipe 6 groups 18.016 4.038 80.491 99.557
threads-pipe 7 groups 14.663 3.991 75.239 99.247
threads-pipe 8 groups 12.242 3.808 70.651 98.644
threads-sockets 1 group 99.990 6.667 99.999 100.000
threads-sockets 2 groups 99.940 5.114 99.997 100.000
threads-sockets 3 groups 99.469 4.115 99.977 100.000
threads-sockets 4 groups 87.528 4.038 99.400 100.000
threads-sockets 5 groups 6.942 2.398 59.244 88.337
threads-sockets 6 groups 4.359 1.954 49.448 87.860
threads-sockets 7 groups 2.845 1.345 41.198 77.102
threads-sockets 8 groups 2.871 1.404 38.512 74.312
schedstat_parse.py -f tbench_vanilla.log
case load se_eff% dom_eff% fast_rate% success_rate%
loopback 28 threads 99.976 18.369 99.995 100.000
loopback 56 threads 99.222 7.799 99.934 100.000
loopback 84 threads 19.723 6.819 70.215 100.000
loopback 112 threads 11.283 5.371 55.371 99.999
loopback 140 threads 0.000 0.000 0.000 0.000
loopback 168 threads 0.000 0.000 0.000 0.000
loopback 196 threads 0.000 0.000 0.000 0.000
loopback 224 threads 0.000 0.000 0.000 0.000
According to the test above, if the system becomes busy, the
SIS Search Efficiency(se_eff%) drops significantly. Although some
benchmarks would finally find an idle CPU(success_rate% = 100%), it is
doubtful whether it is worth it to search the whole LLC domain.
[Proposal]
It would be ideal to have a crystal ball to answer this question:
How many CPUs must a wakeup path walk down, before it can find an idle
CPU? Many potential metrics could be used to predict the number.
One candidate is the sum of util_avg in this LLC domain. The benefit
of choosing util_avg is that it is a metric of accumulated historic
activity, which seems to be smoother than instantaneous metrics
(such as rq->nr_running). Besides, choosing the sum of util_avg
would help predict the load of the LLC domain more precisely, because
SIS_PROP uses one CPU's idle time to estimate the total LLC domain idle
time.
In summary, the lower the util_avg is, the more select_idle_cpu()
should scan for idle CPU, and vice versa. When the sum of util_avg
in this LLC domain hits 85% or above, the scan stops. The reason to
choose 85% as the threshold is that this is the imbalance_pct(117)
when a LLC sched group is overloaded.
Introduce the quadratic function:
y = SCHED_CAPACITY_SCALE - p * x^2
and y'= y / SCHED_CAPACITY_SCALE
x is the ratio of sum_util compared to the CPU capacity:
x = sum_util / (llc_weight * SCHED_CAPACITY_SCALE)
y' is the ratio of CPUs to be scanned in the LLC domain,
and the number of CPUs to scan is calculated by:
nr_scan = llc_weight * y'
Choosing quadratic function is because:
[1] Compared to the linear function, it scans more aggressively when the
sum_util is low.
[2] Compared to the exponential function, it is easier to calculate.
[3] It seems that there is no accurate mapping between the sum of util_avg
and the number of CPUs to be scanned. Use heuristic scan for now.
For a platform with 112 CPUs per LLC, the number of CPUs to scan is:
sum_util% 0 5 15 25 35 45 55 65 75 85 86 ...
scan_nr 112 111 108 102 93 81 65 47 25 1 0 ...
For a platform with 16 CPUs per LLC, the number of CPUs to scan is:
sum_util% 0 5 15 25 35 45 55 65 75 85 86 ...
scan_nr 16 15 15 14 13 11 9 6 3 0 0 ...
Furthermore, to minimize the overhead of calculating the metrics in
select_idle_cpu(), borrow the statistics from periodic load balance.
As mentioned by Abel, on a platform with 112 CPUs per LLC, the
sum_util calculated by periodic load balance after 112 ms would
decay to about 0.5 * 0.5 * 0.5 * 0.7 = 8.75%, thus bringing a delay
in reflecting the latest utilization. But it is a trade-off.
Checking the util_avg in newidle load balance would be more frequent,
but it brings overhead - multiple CPUs write/read the per-LLC shared
variable and introduces cache contention. Tim also mentioned that,
it is allowed to be non-optimal in terms of scheduling for the
short-term variations, but if there is a long-term trend in the load
behavior, the scheduler can adjust for that.
When SIS_UTIL is enabled, the select_idle_cpu() uses the nr_scan
calculated by SIS_UTIL instead of the one from SIS_PROP. As Peter and
Mel suggested, SIS_UTIL should be enabled by default.
This patch is based on the util_avg, which is very sensitive to the
CPU frequency invariance. There is an issue that, when the max frequency
has been clamp, the util_avg would decay insanely fast when
the CPU is idle. Commit addca285120b ("cpufreq: intel_pstate: Handle no_turbo
in frequency invariance") could be used to mitigate this symptom, by adjusting
the arch_max_freq_ratio when turbo is disabled. But this issue is still
not thoroughly fixed, because the current code is unaware of the user-specified
max CPU frequency.
[Test result]
netperf and tbench were launched with 25% 50% 75% 100% 125% 150%
175% 200% of CPU number respectively. Hackbench and schbench were launched
by 1, 2 ,4, 8 groups. Each test lasts for 100 seconds and repeats 3 times.
The following is the benchmark result comparison between
baseline:vanilla v5.19-rc1 and compare:patched kernel. Positive compare%
indicates better performance.
Each netperf test is a:
netperf -4 -H 127.0.1 -t TCP/UDP_RR -c -C -l 100
netperf.throughput
=======
case load baseline(std%) compare%( std%)
TCP_RR 28 threads 1.00 ( 0.34) -0.16 ( 0.40)
TCP_RR 56 threads 1.00 ( 0.19) -0.02 ( 0.20)
TCP_RR 84 threads 1.00 ( 0.39) -0.47 ( 0.40)
TCP_RR 112 threads 1.00 ( 0.21) -0.66 ( 0.22)
TCP_RR 140 threads 1.00 ( 0.19) -0.69 ( 0.19)
TCP_RR 168 threads 1.00 ( 0.18) -0.48 ( 0.18)
TCP_RR 196 threads 1.00 ( 0.16) +194.70 ( 16.43)
TCP_RR 224 threads 1.00 ( 0.16) +197.30 ( 7.85)
UDP_RR 28 threads 1.00 ( 0.37) +0.35 ( 0.33)
UDP_RR 56 threads 1.00 ( 11.18) -0.32 ( 0.21)
UDP_RR 84 threads 1.00 ( 1.46) -0.98 ( 0.32)
UDP_RR 112 threads 1.00 ( 28.85) -2.48 ( 19.61)
UDP_RR 140 threads 1.00 ( 0.70) -0.71 ( 14.04)
UDP_RR 168 threads 1.00 ( 14.33) -0.26 ( 11.16)
UDP_RR 196 threads 1.00 ( 12.92) +186.92 ( 20.93)
UDP_RR 224 threads 1.00 ( 11.74) +196.79 ( 18.62)
Take the 224 threads as an example, the SIS search metrics changes are
illustrated below:
vanilla patched
4544492 +237.5% 15338634 sched_debug.cpu.sis_domain_search.avg
38539 +39686.8% 15333634 sched_debug.cpu.sis_failed.avg
128300000 -87.9% 15551326 sched_debug.cpu.sis_scanned.avg
5842896 +162.7% 15347978 sched_debug.cpu.sis_search.avg
There is -87.9% less CPU scans after patched, which indicates lower overhead.
Besides, with this patch applied, there is -13% less rq lock contention
in perf-profile.calltrace.cycles-pp._raw_spin_lock.raw_spin_rq_lock_nested
.try_to_wake_up.default_wake_function.woken_wake_function.
This might help explain the performance improvement - Because this patch allows
the waking task to remain on the previous CPU, rather than grabbing other CPUs'
lock.
Each hackbench test is a:
hackbench -g $job --process/threads --pipe/sockets -l 1000000 -s 100
hackbench.throughput
=========
case load baseline(std%) compare%( std%)
process-pipe 1 group 1.00 ( 1.29) +0.57 ( 0.47)
process-pipe 2 groups 1.00 ( 0.27) +0.77 ( 0.81)
process-pipe 4 groups 1.00 ( 0.26) +1.17 ( 0.02)
process-pipe 8 groups 1.00 ( 0.15) -4.79 ( 0.02)
process-sockets 1 group 1.00 ( 0.63) -0.92 ( 0.13)
process-sockets 2 groups 1.00 ( 0.03) -0.83 ( 0.14)
process-sockets 4 groups 1.00 ( 0.40) +5.20 ( 0.26)
process-sockets 8 groups 1.00 ( 0.04) +3.52 ( 0.03)
threads-pipe 1 group 1.00 ( 1.28) +0.07 ( 0.14)
threads-pipe 2 groups 1.00 ( 0.22) -0.49 ( 0.74)
threads-pipe 4 groups 1.00 ( 0.05) +1.88 ( 0.13)
threads-pipe 8 groups 1.00 ( 0.09) -4.90 ( 0.06)
threads-sockets 1 group 1.00 ( 0.25) -0.70 ( 0.53)
threads-sockets 2 groups 1.00 ( 0.10) -0.63 ( 0.26)
threads-sockets 4 groups 1.00 ( 0.19) +11.92 ( 0.24)
threads-sockets 8 groups 1.00 ( 0.08) +4.31 ( 0.11)
Each tbench test is a:
tbench -t 100 $job 127.0.0.1
tbench.throughput
======
case load baseline(std%) compare%( std%)
loopback 28 threads 1.00 ( 0.06) -0.14 ( 0.09)
loopback 56 threads 1.00 ( 0.03) -0.04 ( 0.17)
loopback 84 threads 1.00 ( 0.05) +0.36 ( 0.13)
loopback 112 threads 1.00 ( 0.03) +0.51 ( 0.03)
loopback 140 threads 1.00 ( 0.02) -1.67 ( 0.19)
loopback 168 threads 1.00 ( 0.38) +1.27 ( 0.27)
loopback 196 threads 1.00 ( 0.11) +1.34 ( 0.17)
loopback 224 threads 1.00 ( 0.11) +1.67 ( 0.22)
Each schbench test is a:
schbench -m $job -t 28 -r 100 -s 30000 -c 30000
schbench.latency_90%_us
========
case load baseline(std%) compare%( std%)
normal 1 mthread 1.00 ( 31.22) -7.36 ( 20.25)*
normal 2 mthreads 1.00 ( 2.45) -0.48 ( 1.79)
normal 4 mthreads 1.00 ( 1.69) +0.45 ( 0.64)
normal 8 mthreads 1.00 ( 5.47) +9.81 ( 14.28)
*Consider the Standard Deviation, this -7.36% regression might not be valid.
Also, a OLTP workload with a commercial RDBMS has been tested, and there
is no significant change.
There were concerns that unbalanced tasks among CPUs would cause problems.
For example, suppose the LLC domain is composed of 8 CPUs, and 7 tasks are
bound to CPU0~CPU6, while CPU7 is idle:
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7
util_avg 1024 1024 1024 1024 1024 1024 1024 0
Since the util_avg ratio is 87.5%( = 7/8 ), which is higher than 85%,
select_idle_cpu() will not scan, thus CPU7 is undetected during scan.
But according to Mel, it is unlikely the CPU7 will be idle all the time
because CPU7 could pull some tasks via CPU_NEWLY_IDLE.
lkp(kernel test robot) has reported a regression on stress-ng.sock on a
very busy system. According to the sched_debug statistics, it might be caused
by SIS_UTIL terminates the scan and chooses a previous CPU earlier, and this
might introduce more context switch, especially involuntary preemption, which
impacts a busy stress-ng. This regression has shown that, not all benchmarks
in every scenario benefit from idle CPU scan limit, and it needs further
investigation.
Besides, there is slight regression in hackbench's 16 groups case when the
LLC domain has 16 CPUs. Prateek mentioned that we should scan aggressively
in an LLC domain with 16 CPUs. Because the cost to search for an idle one
among 16 CPUs is negligible. The current patch aims to propose a generic
solution and only considers the util_avg. Something like the below could
be applied on top of the current patch to fulfill the requirement:
if (llc_weight <= 16)
nr_scan = nr_scan * 32 / llc_weight;
For LLC domain with 16 CPUs, the nr_scan will be expanded to 2 times large.
The smaller the CPU number this LLC domain has, the larger nr_scan will be
expanded. This needs further investigation.
There is also ongoing work[2] from Abel to filter out the busy CPUs during
wakeup, to further speed up the idle CPU scan. And it could be a following-up
optimization on top of this change.
Suggested-by: Tim Chen <tim.c.chen@intel.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Tested-by: Mohini Narkhede <mohini.narkhede@intel.com>
Tested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Link: https://lore.kernel.org/r/20220612163428.849378-1-yu.c.chen@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4c46091ee985ae84c60c5e95055d779fcd291d87 upstream.
Syzbot found a Use After Free bug in compute_effective_progs().
The reproducer creates a number of BPF links, and causes a fault
injected alloc to fail, while calling bpf_link_detach on them.
Link detach triggers the link to be freed by bpf_link_free(),
which calls __cgroup_bpf_detach() and update_effective_progs().
If the memory allocation in this function fails, the function restores
the pointer to the bpf_cgroup_link on the cgroup list, but the memory
gets freed just after it returns. After this, every subsequent call to
update_effective_progs() causes this already deallocated pointer to be
dereferenced in prog_list_length(), and triggers KASAN UAF error.
To fix this issue don't preserve the pointer to the prog or link in the
list, but remove it and replace it with a dummy prog without shrinking
the table. The subsequent call to __cgroup_bpf_detach() or
__cgroup_bpf_detach() will correct it.
Fixes: af6eea57437a ("bpf: Implement bpf_link-based cgroup BPF program attachment")
Reported-by: <syzbot+f264bffdfbd5614f3bb2@syzkaller.appspotmail.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://syzkaller.appspot.com/bug?id=8ebf179a95c2a2670f7cf1ba62429ec044369db4
Link: https://lore.kernel.org/bpf/20220517180420.87954-1-tadeusz.struk@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
first waiter
commit 6eebd5fb20838f5971ba17df9f55cc4f84a31053 upstream.
With commit d257cc8cb8d5 ("locking/rwsem: Make handoff bit handling more
consistent"), the writer that sets the handoff bit can be interrupted
out without clearing the bit if the wait queue isn't empty. This disables
reader and writer optimistic lock spinning and stealing.
Now if a non-first writer in the queue is somehow woken up or a new
waiter enters the slowpath, it can't acquire the lock. This is not the
case before commit d257cc8cb8d5 as the writer that set the handoff bit
will clear it when exiting out via the out_nolock path. This is less
efficient as the busy rwsem stays in an unlock state for a longer time.
In some cases, this new behavior may cause lockups as shown in [1] and
[2].
This patch allows a non-first writer to ignore the handoff bit if it
is not originally set or initiated by the first waiter. This patch is
shown to be effective in fixing the lockup problem reported in [1].
[1] https://lore.kernel.org/lkml/20220617134325.GC30825@techsingularity.net/
[2] https://lore.kernel.org/lkml/3f02975c-1a9d-be20-32cf-f1d8e3dfafcc@oracle.com/
Fixes: d257cc8cb8d5 ("locking/rwsem: Make handoff bit handling more consistent")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Link: https://lore.kernel.org/r/20220622200419.778799-1-longman@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e64ab2dbd882933b65cd82ff6235d705ad65dbb6 upstream.
If a watch is being added to a queue, it needs to guard against
interference from addition of a new watch, manual removal of a watch and
removal of a watch due to some other queue being destroyed.
KEYCTL_WATCH_KEY guards against this for the same {key,queue} pair by
holding the key->sem writelocked and by holding refs on both the key and
the queue - but that doesn't prevent interaction from other {key,queue}
pairs.
While add_watch_to_object() does take the spinlock on the event queue,
it doesn't take the lock on the source's watch list. The assumption was
that the caller would prevent that (say by taking key->sem) - but that
doesn't prevent interference from the destruction of another queue.
Fix this by locking the watcher list in add_watch_to_object().
Fixes: c73be61cede5 ("pipe: Add general notification queue support")
Reported-by: syzbot+03d7b43290037d1f87ca@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: keyrings@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e0339f036ef4beb9b20f0b6532a1e0ece7f594c6 upstream.
Since __post_watch_notification() walks wlist->watchers with only the
RCU read lock held, we need to use RCU methods to add to the list (we
already use RCU methods to remove from the list).
Fix add_watch_to_object() to use hlist_add_head_rcu() instead of
hlist_add_head() for that list.
Fixes: c73be61cede5 ("pipe: Add general notification queue support")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 44e29e64cf1ac0cffb152e0532227ea6d002aa28 upstream.
Sedat Dilek noticed that I had an extraneous semicolon at the end of a
line in the previous patch.
It's harmless, but unintentional, and while compilers just treat it as
an extra empty statement, for all I know some other tooling might warn
about it. So clean it up before other people notice too ;)
Fixes: 353f7988dd84 ("watchqueue: make sure to serialize 'wqueue->defunct' properly")
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 353f7988dd8413c47718f7ca79c030b6fb62cfe5 upstream.
When the pipe is closed, we mark the associated watchqueue defunct by
calling watch_queue_clear(). However, while that is protected by the
watchqueue lock, new watchqueue entries aren't actually added under that
lock at all: they use the pipe->rd_wait.lock instead, and looking up
that pipe happens without any locking.
The watchqueue code uses the RCU read-side section to make sure that the
wqueue entry itself hasn't disappeared, but that does not protect the
pipe_info in any way.
So make sure to actually hold the wqueue lock when posting watch events,
properly serializing against the pipe being torn down.
Reported-by: Noam Rathaus <noamr@ssd-disclosure.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b27f266f74fbda4ee36c2b2b04d15992860cf23b ]
Setting set_event_pid with trailing whitespace lead to endless write
system calls like below.
$ strace echo "123 " > /sys/kernel/debug/tracing/set_event_pid
execve("/usr/bin/echo", ["echo", "123 "], ...) = 0
...
write(1, "123 \n", 5) = 4
write(1, "\n", 1) = 0
write(1, "\n", 1) = 0
write(1, "\n", 1) = 0
write(1, "\n", 1) = 0
write(1, "\n", 1) = 0
....
This is because, the result of trace_get_user's are not returned when it
read at least one pid. To fix it, update read variable even if
parser->idx == 0.
The result of applied patch is below.
$ strace echo "123 " > /sys/kernel/debug/tracing/set_event_pid
execve("/usr/bin/echo", ["echo", "123 "], ...) = 0
...
write(1, "123 \n", 5) = 5
close(1) = 0
Link: https://lkml.kernel.org/r/20220503050546.288911-1-vvghjk1234@gmail.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Baik Song An <bsahn@etri.re.kr>
Cc: Hong Yeon Kim <kimhy@etri.re.kr>
Cc: Taeung Song <taeung@reallinux.co.kr>
Cc: linuxgeek@linuxgeek.io
Cc: stable@vger.kernel.org
Fixes: 4909010788640 ("tracing: Add set_event_pid directory for future use")
Signed-off-by: Wonhyuk Yang <vvghjk1234@gmail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6954e415264eeb5ee6be0d22d789ad12c995ee64 ]
Instead of having the logic that does trace_pid_list open coded, wrap it in
abstract functions. This will allow a rewrite of the logic that implements
the trace_pid_list without affecting the users.
Note, this causes a change in behavior. Every time a pid is written into
the set_*_pid file, it creates a new list and uses RCU to update it. If
pid_max is lowered, but there was a pid currently in the list that was
higher than pid_max, those pids will now be removed on updating the list.
The old behavior kept that from happening.
The rewrite of the pid_list logic will no longer depend on pid_max,
and will return the old behavior.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
