| Age | Commit message (Collapse) | Author |
|---|
|
This improves compatbility with a lot of headset / chipset
combinations. Ideally this should not be needed.
Change-Id: I8b676701e12e416aa7d60801b9d353b15d102709
Signed-off-by: hyungseoung.yoo <hyungseoung.yoo@samsung.com>
Signed-off-by: Jaikumar Ganesh <jaikumarg@android.com>
|
|
__u16 sco_pkt_type is introduced to struct sockaddr_sco. It allows bitwise
selection of SCO/eSCO packet types. Currently those bits are:
0x0001 HV1 may be used.
0x0002 HV2 may be used.
0x0004 HV3 may be used.
0x0008 EV3 may be used.
0x0010 EV4 may be used.
0x0020 EV5 may be used.
0x0040 2-EV3 may be used.
0x0080 3-EV3 may be used.
0x0100 2-EV5 may be used.
0x0200 3-EV5 may be used.
This is similar to the Packet Type parameter in the HCI Setup Synchronous
Connection Command, except that we are not reversing the logic on the EDR bits.
This makes the use of sco_pkt_tpye forward portable for the use case of
white-listing packet types, which we expect will be the primary use case.
If sco_pkt_type is zero, or userspace uses the old struct sockaddr_sco,
then the default behavior is to allow all packet types.
Packet type selection is just a request made to the Bluetooth chipset, and
it is up to the link manager on the chipset to negiotiate and decide on the
actual packet types used. Furthermore, when a SCO/eSCO connection is eventually
made there is no way for the host stack to determine which packet type was used
(however it is possible to get the link type of SCO or eSCO).
sco_pkt_type is ignored for incoming SCO connections. It is possible
to add this in the future as a parameter to the Accept Synchronous Connection
Command, however its a little trickier because the kernel does not
currently preserve sockaddr_sco data between userspace calls to accept().
The most common use for sco_pkt_type will be to white-list only SCO packets,
which can be done with the hci.h constant SCO_ESCO_MASK.
This patch is motivated by broken Bluetooth carkits such as the Motorolo
HF850 (it claims to support eSCO, but will actually reject eSCO connections
after 5 seconds) and the 2007/2008 Infiniti G35/37 (fails to route audio
if a 2-EV5 packet type is negiotiated). With this patch userspace can maintain
a list of compatible packet types to workaround remote devices such as these.
Based on a patch by Marcel Holtmann.
Rebased to 2.6.39.
Change-Id: Ide1c89574fa4f6f1b9218282e1af17051eb86315
Signed-off-by: Nick Pelly <npelly@google.com>
|
|
This is to support the Motorola HF850 carkit which reports the error code 0x10
for an eSCO attempt, even though it advertises eSCO support. Here is the
hcidump:
2009-09-22 15:40:24.492391 < HCI Command: Setup Synchronous Connection
(0x01|0x0028) plen 17
handle 1 voice setting 0x0060
2009-09-22 15:40:24.493002 > HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2009-09-22 15:40:30.594869 > HCI Event: Synchronous Connect Complete (0x2c)
plen 17
status 0x10 handle 257 bdaddr 00:50:CD:20:C6:84 type eSCO
Error: Connection Accept Timeout Exceeded
With this patch we will retry with a SCO connection, which succeeds.
Unfortunately the Moto HF850 also takes 5 seconds to return the error for the
eSCO attempt, so it will still take 5 seconds to fallback to SCO with this
patch.
Signed-off-by: Nick Pelly <npelly@google.com>
|
|
The checks for HCI_INQUIRY and HCI_MGMT were in the wrong order,
so that second scans always failed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
In some cases it will be useful having the key size used for
encrypting the link. For example, some profiles may restrict
some operations depending on the key length.
The key size is stored in the key that is passed to userspace
using the pin_length field in the key structure.
For now this field is only valid for LE controllers. 3.0+HS
controllers define the Read Encryption Key Size command, this
field is intended for storing the value returned by that
command.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Now that we have methods to finding keys by its parameters we can
reject an encryption request if the key isn't found.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a new module parameter to enable/disable host LE
support. By default host LE support is disabled.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a handler to Write LE Host Supported command complete
events. Once this commands has completed successfully, we should
read the extended LMP features and update the extfeatures field in
hci_dev.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This new field holds the extended LMP features value. Some LE
mechanism such as discovery procedure needs to read the extended
LMP features to work properly.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch implements a simple version of the SMP Pairing Features
exchange procedure (Vol. 3 Part H, Section 2.3.5.1).
For now, everything that would cause a Pairing Method different of
Just Works to be chosen is rejected.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
As the default security level (BT_SECURITY_SDP) doesn't make sense for
LE links, initialize LE links with something that makes sense.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This adds support for starting SMP Phase 2 Encryption, when the initial
SMP negotiation is successful. This adds the LE Start Encryption and LE
Long Term Key Request commands and related events.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Conflicts:
net/bluetooth/rfcomm/sock.c
|
|
Some old hci controllers do not accept any mask so leave the
default mask on for these devices.
< HCI Command: Set Event Mask (0x03|0x0001) plen 8
Mask: 0xfffffbff00000000
> HCI Event: Command Complete (0x0e) plen 4
Set Event Mask (0x03|0x0001) ncmd 1
status 0x12
Error: Invalid HCI Command Parameters
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Tested-by: Corey Boyle <corey@kansanian.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a new field (dst_type) to the struct hci_conn which
holds the type of the destination address (bdaddr_t dst). This
approach is needed in order to use the struct hci_conn as an
abstraction of LE connections in HCI Layer. For non-LE this field
is ignored.
This patch also set properly the 'dst_type' field after initializing
LE hci_conn structures.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Replace if(conn) with if(!conn) checking to avoid too many nested statements
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Legacy devices don't re-authenticate the link properly if a link key
already exists. Thus, don't update sec_level for this case even if
hci_auth_complete_evt indicates success. Otherwise the sec_level will
not reflect a real security on the link.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a timer to clear 'adv_entries' after three minutes.
After some amount of time, the advertising entries cached during
the last LE scan should be considered expired and they should be
removed from the advertising cache.
It was chosen a three minutes timeout as an initial attempt. This
value might change in future.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
The LE advertising cache should be cleared before performing a LE
scanning. This will force the cache to contain only fresh advertising
entries.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a function to handle LE Advertising Report Meta
Events.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
We need to be able for receive events notifying that the connection
was established, the connection attempt failed or that disconnection
happened.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
In some circumstances hci_get_auth_req will return a value different
from the current conn->auth_type. In these cases update conn->auth_type
so that when a user confirm request comes it doesn't falsely trigger
auto-accept.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Link keys should only be stored if very specific criteria of the
authentication process are fulfilled. This patch essentially copies the
criteria that user space has so far been using to the kernel side so
that the management interface works properly.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
The mgmt_ev_pin_code_request event should not be sent to user space if
the request gets rejected by the kernel due to the pairable flag not
being set.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
"Pairing not allowed" is 0x18 and not 0x16.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
When accepting a pairing request which fulfills the SSP auto-accept
criteria we need to push the request all the way to the user for
confirmation. This patch adds a new hint to the user_confirm_request
management event so user space can know when to show a numeric
comparison dialog and when to show a simple yes/no confirmation dialog.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
The HCI_CONN_AUTH_PEND flag should be set whenever requesting
authentication so that multiple pending requests can't occur.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Some test systems require an arbitrary delay to the auto-accept test
cases for Secure Simple Pairing in order for the tests to pass.
Previously when this was handled in user space it was worked around by
code modifications and recompilation, but now that it's on the kernel
side it's more convenient if there's a debugfs interface for it.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds automated negative and positive (auto-accept) responses
for Secure Simple Pairing user confirmation requests. The responses are
only sent if the HCI_MGMT flag is set in order not to confuse older user
space versions (without management interface support).
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Extend the mgmt_pin_code_request interface to require secure
pin code (16 digit) for authentication.
This is a kernel part of the secure pin code requirement notification
to user space agent.
Code styling fix by Johan Hedberg.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
If host requires MITM protection notify that to controller in
io capabilities reply even if the remote device requires no bonding.
If it is not respected, host can get an unauthenticated link key while
it expects authenticated one.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
High security level for pre v2.1 devices requires combination link key
authenticated by at least 16 digit PIN code.
It's also necessary to update key_type and pin_length when the key
exists and is sufficently secured for the connection as there will be
no link key notify event in that case.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Keep the link key type together with connection and use it to
map security level to link key requirements. Authenticate and/or
encrypt connection if the link is insufficiently secure.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
If authentication fails the security level should stay as it was set
before the process has started. Setting BT_SECURITY_LOW can hide real
security level on a link eg. having BT_SECURITY_MEDIUM on the link,
re-authenticate with failure to get BT_SECURITY_HIGH, as a result we
get BT_SECURITY_LOW on the link while the real security is still medium.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Introduce the link key types defs and use them instead of magic numbers.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a new event to the Management interface to track when
local adapters are discovering remote devices. For now this only tracks
BR/EDR discovery procedures.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Conflicts:
net/bluetooth/l2cap_core.c
net/bluetooth/l2cap_sock.c
net/bluetooth/mgmt.c
|
|
hci_io_capa_reply_evt() holds reference for hciconnection. It's useless since
hci_io_capa_request_evt()/hci_simple_pair_complete_evt() already protects the
connection. In addition it leaves connection open after failed SSP pairing.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Use kernel stored remote Out Of Band data only if management interface
is enabled. Otherwise HCI_OP_REMOTE_OOB_DATA_NEG_REPLY was sent to
controller even if remote Out Of Band data was present in bluetoothd.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a new remote_name event to the Management interface
which is sent every time the name of a remote device is resolved (over
BR/EDR).
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a device_found event to the Management interface. For
now the event only maps to BR/EDR inquiry result HCI events, but in the
future the plan is to also use it for the LE device discovery process.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-2.6
|
|
We can't send new commands before a cmd_complete for the HCI_RESET command
shows up.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Reported-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
|
|
If remote side reports oob availability or we are pairing initiator
use oob data for pairing if available.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds commands to add and remove remote OOB data to the managment
interface. Remote data is stored in kernel and can be used by corresponding
HCI commands and events when needed.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a command to read local OOB data to the managment interface.
The command maps directly to the Read Local OOB Data HCI command.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a new set_local_name management command as well as a
local_name_changed management event. With these user space can both
change the local name as well as monitor changes to it by others.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This patch adds a clear define for the maximum device name length in HCI
messages and thereby avoids magic numbers in the code.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
We can't send new commands before a cmd_complete for the HCI_RESET command
shows up.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Reported-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
|
|
To properly track bonding completion an event to indicate authentication
failure is needed. This event will be sent whenever an authentication
complete HCI event with a non-zero status comes. It will also be sent
when we're acting in acceptor role for SSP authentication in which case
the controller will send a Simple Pairing Complete event.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
