Age | Commit message (Collapse) | Author |
|
[ Upstream commit 5f35227ea34bb616c436d9da47fc325866c428f3 ]
GSO isn't the only offload feature with restrictions that
potentially can't be expressed with the current features mechanism.
Checksum is another although it's a general issue that could in
theory apply to anything. Even if it may be possible to
implement these restrictions in other ways, it can result in
duplicate code or inefficient per-packet behavior.
This generalizes ndo_gso_check so that drivers can remove any
features that don't make sense for a given packet, similar to
netif_skb_features(). It also converts existing driver
restrictions to the new format, completing the work that was
done to support tunnel protocols since the issues apply to
checksums as well.
By actually removing features from the set that are used to do
offloading, it solves another problem with the existing
interface. In these cases, GSO would run with the original set
of features and not do anything because it appears that
segmentation is not required.
CC: Tom Herbert <therbert@google.com>
CC: Joe Stringer <joestringer@nicira.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Tom Herbert <therbert@google.com>
Fixes: 04ffcb255f22 ("net: Add ndo_gso_check")
Tested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2c26d34bbcc0b3f30385d5587aa232289e2eed8e ]
When using VXLAN tunnels and a sky2 device, I have experienced
checksum failures of the following type:
[ 4297.761899] eth0: hw csum failure
[...]
[ 4297.765223] Call Trace:
[ 4297.765224] <IRQ> [<ffffffff8172f026>] dump_stack+0x46/0x58
[ 4297.765235] [<ffffffff8162ba52>] netdev_rx_csum_fault+0x42/0x50
[ 4297.765238] [<ffffffff8161c1a0>] ? skb_push+0x40/0x40
[ 4297.765240] [<ffffffff8162325c>] __skb_checksum_complete+0xbc/0xd0
[ 4297.765243] [<ffffffff8168c602>] tcp_v4_rcv+0x2e2/0x950
[ 4297.765246] [<ffffffff81666ca0>] ? ip_rcv_finish+0x360/0x360
These are reliably reproduced in a network topology of:
container:eth0 == host(OVS VXLAN on VLAN) == bond0 == eth0 (sky2) -> switch
When VXLAN encapsulated traffic is received from a similarly
configured peer, the above warning is generated in the receive
processing of the encapsulated packet. Note that the warning is
associated with the container eth0.
The skbs from sky2 have ip_summed set to CHECKSUM_COMPLETE, and
because the packet is an encapsulated Ethernet frame, the checksum
generated by the hardware includes the inner protocol and Ethernet
headers.
The receive code is careful to update the skb->csum, except in
__dev_forward_skb, as called by dev_forward_skb. __dev_forward_skb
calls eth_type_trans, which in turn calls skb_pull_inline(skb, ETH_HLEN)
to skip over the Ethernet header, but does not update skb->csum when
doing so.
This patch resolves the problem by adding a call to
skb_postpull_rcsum to update the skb->csum after the call to
eth_type_trans.
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b8fb4e0648a2ab3734140342002f68fb0c7d1602 ]
skb_scrub_packet() is called when a packet switches between a context
such as between underlay and overlay, between namespaces, or between
L3 subnets.
While we already scrub the packet mark, connection tracking entry,
and cached destination, the security mark/context is left intact.
It seems wrong to inherit the security context of a packet when going
from overlay to underlay or across forwarding paths.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 796f2da81bead71ffc91ef70912cd8d1827bf756 ]
When vlan tags are stacked, it is very likely that the outer tag is stored
in skb->vlan_tci and skb->protocol shows the inner tag's vlan_proto.
Currently netif_skb_features() first looks at skb->protocol even if there
is the outer tag in vlan_tci, thus it incorrectly retrieves the protocol
encapsulated by the inner vlan instead of the inner vlan protocol.
This allows GSO packets to be passed to HW and they end up being
corrupted.
Fixes: 58e998c6d239 ("offloading: Force software GSO for multiple vlan tags.")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit af6dabc9c70ae3f307685b1f32f52d60b1bf0527 ]
Commit cecda693a969816bac5e470e1d9c9c0ef5567bca ("net: keep original skb
which only needs header checking during software GSO") keeps the original
skb for packets that only needs header check, but it doesn't drop the
packet if software segmentation or header check were failed.
Fixes cecda693a9 ("net: keep original skb which only needs header checking during software GSO")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
rtnl_link_get_net() holds a reference on the 'struct net', we need to release
it in case of error.
CC: Eric W. Biederman <ebiederm@xmission.com>
Fixes: b51642f6d77b ("net: Enable a userns root rtnl calls that are safe for unprivilged users")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only search for IFLA_EXT_MASK if the message actually carries a
ifinfomsg header and validate minimal length requirements for
IFLA_EXT_MASK.
Fixes: 6cbdceeb ("bridge: Dump vlan information from a bridge port")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Payload is currently accessed blindly and may exceed valid message
boundaries.
Fixes: 407af3299 ("bridge: Add netlink interface to configure vlans on bridge ports")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not sure what I was thinking, but doing anything after
releasing a refcount is suicidal or/and embarrassing.
By the time we set skb->fclone to SKB_FCLONE_FREE, another cpu
could have released last reference and freed whole skb.
We potentially corrupt memory or trap if CONFIG_DEBUG_PAGEALLOC is set.
Reported-by: Chris Mason <clm@fb.com>
Fixes: ce1a4ea3f1258 ("net: avoid one atomic operation in skb_clone()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a driver supports reading EEPROM but no EEPROM is installed in the system,
the driver's get_eeprom_len function returns 0. ethtool will subsequently
try to read that zero-length EEPROM anyway. If the driver does not support
EEPROM access at all, this operation will return -EOPNOTSUPP. If the driver
does support EEPROM access but no EEPROM is installed, the operation will
return -EINVAL. Return -EOPNOTSUPP in both cases for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not reuse skb if it was pfmemalloc tainted, otherwise
future frame might be dropped anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The crafted header start address is from a driver supplied buffer, which
one can reasonably expect to be aligned on a 4-bytes boundary.
However ATM the TSO helper API is only used by ethernet drivers and
the tcp header will then be aligned to a 2-bytes only boundary from the
header start address.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
if ->encapsulation is set we have to use inner_tcp_hdrlen and add the
size of the inner network headers too.
This is 'mostly harmless'; tbf might send skb that is slightly over
quota or drop skb even if it would have fit.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Include fixes for netrom and dsa (Fabian Frederick and Florian
Fainelli)
2) Fix FIXED_PHY support in stmmac, from Giuseppe CAVALLARO.
3) Several SKB use after free fixes (vxlan, openvswitch, vxlan,
ip_tunnel, fou), from Li ROngQing.
4) fec driver PTP support fixes from Luwei Zhou and Nimrod Andy.
5) Use after free in virtio_net, from Michael S Tsirkin.
6) Fix flow mask handling for megaflows in openvswitch, from Pravin B
Shelar.
7) ISDN gigaset and capi bug fixes from Tilman Schmidt.
8) Fix route leak in ip_send_unicast_reply(), from Vasily Averin.
9) Fix two eBPF JIT bugs on x86, from Alexei Starovoitov.
10) TCP_SKB_CB() reorganization caused a few regressions, fixed by Cong
Wang and Eric Dumazet.
11) Don't overwrite end of SKB when parsing malformed sctp ASCONF
chunks, from Daniel Borkmann.
12) Don't call sock_kfree_s() with NULL pointers, this function also has
the side effect of adjusting the socket memory usage. From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
bna: fix skb->truesize underestimation
net: dsa: add includes for ethtool and phy_fixed definitions
openvswitch: Set flow-key members.
netrom: use linux/uaccess.h
dsa: Fix conversion from host device to mii bus
tipc: fix bug in bundled buffer reception
ipv6: introduce tcp_v6_iif()
sfc: add support for skb->xmit_more
r8152: return -EBUSY for runtime suspend
ipv4: fix a potential use after free in fou.c
ipv4: fix a potential use after free in ip_tunnel_core.c
hyperv: Add handling of IP header with option field in netvsc_set_hash()
openvswitch: Create right mask with disabled megaflows
vxlan: fix a free after use
openvswitch: fix a use after free
ipv4: dst_entry leak in ip_send_unicast_reply()
ipv4: clean up cookie_v4_check()
ipv4: share tcp_v4_save_options() with cookie_v4_check()
ipv4: call __ip_options_echo() in cookie_v4_check()
atm: simplify lanai.c by using module_pci_driver
...
|
|
Add ndo_gso_check which a device can define to indicate whether is
is capable of doing GSO on a packet. This funciton would be called from
the stack to determine whether software GSO is needed to be done. A
driver should populate this function if it advertises GSO types for
which there are combinations that it wouldn't be able to handle. For
instance a device that performs UDP tunneling might only implement
support for transparent Ethernet bridging type of inner packets
or might have limitations on lengths of inner headers.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
|
|
Unlike normal kfree() it is never right to call sock_kfree_s() with
a NULL pointer, because sock_kfree_s() also has the side effect of
discharging the memory from the sockets quota.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is illegal to use atomic_set(&page->_count, ...) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
The only case it is valid is when page->_count is 0
Fixes: 540eb7bf0bbed ("net: Update alloc frag to reduce get/put page usage and recycle pages")
Signed-off-by: Eric Dumaze <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses a kernel unaligned access bug seen on a sparc64 system
with an igb adapter. Specifically the __skb_flow_get_ports was returning a
be32 pointer which was then having the value directly returned.
In order to prevent this it is actually easier to simply not populate the
ports or address values when an skb is not present. In this case the
assumption is that the data isn't needed and rather than slow down the
faster aligned accesses by making them have to assume the unaligned path on
architectures that don't support efficent unaligned access it makes more
sense to simply switch off the bits that were copying the source and
destination address/port for the case where we only care about the protocol
types and lengths which are normally 16 bit fields anyway.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. sk_run_filter has been renamed, sk_filter() is using SK_RUN_FILTER.
2. Remove wrong comments about storing intermediate value.
3. replace sk_run_filter with __bpf_prog_run for check_load_and_stores's
comments
Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix following warning.
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'header_len'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'data_len'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'max_page_order'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'errcode'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'gfp_mask'
Acutually the descriptions exist, but missing "@" in front.
This problem start to happen when following commit was merged
into Linus's tree during 3.18-rc1 merge period.
commit 2e4e44107176d552f8bb1bb76053e850e3809841
net: add alloc_skb_with_frags() helper
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine updates from Dan Williams:
"Even though this has fixes marked for -stable, given the size and the
needed conflict resolutions this is 3.18-rc1/merge-window material.
These patches have been languishing in my tree for a long while. The
fact that I do not have the time to do proper/prompt maintenance of
this tree is a primary factor in the decision to step down as
dmaengine maintainer. That and the fact that the bulk of drivers/dma/
activity is going through Vinod these days.
The net_dma removal has not been in -next. It has developed simple
conflicts against mainline and net-next (for-3.18).
Continuing thanks to Vinod for staying on top of drivers/dma/.
Summary:
1/ Step down as dmaengine maintainer see commit 08223d80df38
"dmaengine maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13
(commit 77873803363c "net_dma: mark broken"), without reports of
performance regression.
3/ Miscellaneous fixes"
* tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
net: make tcp_cleanup_rbuf private
net_dma: revert 'copied_early'
net_dma: simple removal
dmaengine maintainer update
dmatest: prevent memory leakage on error path in thread
ioat: Use time_before_jiffies()
dmaengine: fix xor sources continuation
dma: mv_xor: Rename __mv_xor_slot_cleanup() to mv_xor_slot_cleanup()
dma: mv_xor: Remove all callers of mv_xor_slot_cleanup()
dma: mv_xor: Remove unneeded mv_xor_clean_completed_slots() call
ioat: Use pci_enable_msix_exact() instead of pci_enable_msix()
drivers: dma: Include appropriate header file in dca.c
drivers: dma: Mark functions as static in dma_v3.c
dma: mv_xor: Add DMA API error checks
ioat/dca: Use dev_is_pci() to check whether it is pci device
|
|
Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.
Current handling of IFF_XMIT_DST_RELEASE is not optimal.
Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y
The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.
As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.
This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.
Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :
dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
netif_keep_dst(dev);
Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.
The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Probably not a big deal, but we'd better just use the
one we get in retry loop.
Fixes: commit 22e0f8b9322cb1a48b1357e8 ("net: sched: make bstats per cpu and estimator RCU safe")
Reported-by: Joe Perches <joe@perches.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marking this as static allows compiler to inline it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some TSO engines might have a too heavy setup cost, that impacts
performance on hosts sending small bursts (2 MSS per packet).
This patch adds a device gso_min_segs, allowing drivers to set
a minimum segment size for TSO packets, according to the NIC
performance.
Tested on a mlx4 NIC, this allows to get a ~110% increase of
throughput when sending 2 MSS per packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use new ethtool [sg]et_tunable() to set tx_copybread (inline threshold)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Its unfortunate we have to walk again skb list to find the tail
after segmentation, even if data is probably hot in cpu caches.
skb_segment() can store the tail of the list into segs->prev,
and validate_xmit_skb_list() can immediately get the tail.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains another batch with Netfilter/IPVS updates
for net-next, they are:
1) Add abstracted ICMP codes to the nf_tables reject expression. We
introduce four reasons to reject using ICMP that overlap in IPv4
and IPv6 from the semantic point of view. This should simplify the
maintainance of dual stack rule-sets through the inet table.
2) Move nf_send_reset() functions from header files to per-family
nf_reject modules, suggested by Patrick McHardy.
3) We have to use IS_ENABLED(CONFIG_BRIDGE_NETFILTER) everywhere in the
code now that br_netfilter can be modularized. Convert remaining spots
in the network stack code.
4) Use rcu_barrier() in the nf_tables module removal path to ensure that
we don't leave object that are still pending to be released via
call_rcu (that may likely result in a crash).
5) Remove incomplete arch 32/64 compat from nft_compat. The original (bad)
idea was to probe the word size based on the xtables match/target info
size, but this assumption is wrong when you have to dump the information
back to userspace.
6) Allow to filter from prerouting and postrouting in the nf_tables bridge.
In order to emulate the ebtables NAT chains (which are actually simple
filter chains with no special semantics), we have support filtering from
this hooks too.
7) Add explicit module dependency between xt_physdev and br_netfilter.
This provides a way to detect if the user needs br_netfilter from
the configuration path. This should reduce the breakage of the
br_netfilter modularization.
8) Cleanup coding style in ip_vs.h, from Simon Horman.
9) Fix crash in the recently added nf_tables masq expression. We have
to register/unregister the notifiers to clean up the conntrack table
entries from the module init/exit path, not from the rule addition /
deletion path. From Arturo Borrero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SKB_FCLONE_UNAVAILABLE has overloaded meaning depending on type of skb.
1: If skb is allocated from head_cache, it indicates fclone is not available.
2: If skb is a companion fclone skb (allocated from fclone_cache), it indicates
it is available to be used.
To avoid confusion for case 2 above, this patch replaces
SKB_FCLONE_UNAVAILABLE with SKB_FCLONE_FREE where appropriate. For fclone
companion skbs, this indicates it is free for use.
SKB_FCLONE_UNAVAILABLE will now simply indicate skb is from head_cache and
cannot / will not have a companion fclone.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_gro_receive() is only called from tcp_gro_receive() which is
not in a module.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Validation of skb can be pretty expensive :
GSO segmentation and/or checksum computations.
We can do this without holding qdisc lock, so that other cpus
can queue additional packets.
Trick is that requeued packets were already validated, so we carry
a boolean so that sch_direct_xmit() can validate a fresh skb list,
or directly use an old one.
Tested on 40Gb NIC (8 TX queues) and 200 concurrent flows, 48 threads
host.
Turning TSO on or off had no effect on throughput, only few more cpu
cycles. Lock contention on qdisc lock disappeared.
Same if disabling TX checksum offload.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In 34666d4 ("netfilter: bridge: move br_netfilter out of the core"),
the bridge netfilter code has been modularized.
Use IS_ENABLED instead of ifdef to cover the module case.
Fixes: 34666d4 ("netfilter: bridge: move br_netfilter out of the core")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch demonstrates the effect of delaying update of HW tailptr.
(based on earlier patch by Jesper)
burst=1 is the default. It sends one packet with xmit_more=false
burst=2 sends one packet with xmit_more=true and
2nd copy of the same packet with xmit_more=false
burst=3 sends two copies of the same packet with xmit_more=true and
3rd copy with xmit_more=false
Performance with ixgbe (usec 30):
burst=1 tx:9.2 Mpps
burst=2 tx:13.5 Mpps
burst=3 tx:14.5 Mpps full 10G line rate
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fast clone cloning can actually avoid an atomic_inc(), if we
guarantee prior clone_ref value is 1.
This requires a change kfree_skbmem(), to perform the
atomic_dec_and_test() on clone_ref before setting fclone to
SKB_FCLONE_UNAVAILABLE.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lets use a proper structure to clearly document and implement
skb fast clones.
Then, we might experiment more easily alternative layouts.
This patch adds a new skb_fclone_busy() helper, used by tcp and xfrm,
to stop leaking of implementation details.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After previous patches to simplify qstats the qstats can be
made per cpu with a packed union in Qdisc struct.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes the use of qstats->qlen variable from the classifiers
and makes it an explicit argument to gnet_stats_copy_queue().
The qlen represents the qdisc queue length and is packed into
the qstats at the last moment before passnig to user space. By
handling it explicitely we avoid, in the percpu stats case, having
to figure out which per_cpu variable to put it in.
It would probably be best to remove it from qstats completely
but qstats is a user space ABI and can't be broken. A future
patch could make an internal only qstats structure that would
avoid having to allocate an additional u32 variable on the
Qdisc struct. This would make the qstats struct 128bits instead
of 128+32.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to run qdisc's without locking statistics and estimators
need to be handled correctly.
To resolve bstats make the statistics per cpu. And because this is
only needed for qdiscs that are running without locks which is not
the case for most qdiscs in the near future only create percpu
stats when qdiscs set the TCQ_F_CPUSTATS flag.
Next because estimators use the bstats to calculate packets per
second and bytes per second the estimator code paths are updated
to use the per cpu statistics.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 8a29111c7ca6 ("net: gro: allow to build full sized skb")
I added a regression for linear skb that traditionally force GRO
to use the frag_list fallback.
Erez Shitrit found that at most two segments were aggregated and
the "if (skb_gro_len(p) != pinfo->gso_size)" test was failing.
This is because pinfo at this spot still points to the last skb in the
chain, instead of the first one, where we find the correct gso_size
information.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 8a29111c7ca6 ("net: gro: allow to build full sized skb")
Reported-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With proliferation of bit fields in sk_buff, __copy_skb_header() became
quite expensive, showing as the most expensive function in a GSO
workload.
__copy_skb_header() performance is also critical for non GSO TCP
operations, as it is used from skb_clone()
This patch carefully moves all the fields that were not copied in a
separate zone : cloned, nohdr, fclone, peeked, head_frag, xmit_more
Then I moved all other fields and all other copied fields in a section
delimited by headers_start[0]/headers_end[0] section so that we
can use a single memcpy() call, inlined by compiler using long
word load/stores.
I also tried to make all copies in the natural orders of sk_buff,
to help hardware prefetching.
I made sure sk_buff size did not change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Per commit "77873803363c net_dma: mark broken" net_dma is no longer used
and there is no plan to fix it.
This is the mechanical removal of bits in CONFIG_NET_DMA ifdef guards.
Reverting the remainder of the net_dma induced changes is deferred to
subsequent patches.
Marked for stable due to Roman's report of a memory leak in
dma_pin_iovec_pages():
https://lkml.org/lkml/2014/9/3/177
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: David Whipple <whipple@securedatainnovations.ch>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: <stable@vger.kernel.org>
Reported-by: Roman Gushchin <klamm@yandex-team.ru>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Cache skb_shinfo(skb) in a variable to avoid computing it multiple
times.
Reorganize the tests to remove one indentation level.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
csum_partial() is a generic function which is not optimised for small fixed
length calculations, and its use requires to store "from" and "to" values in
memory while we already have them available in registers. This also has impact,
especially on RISC processors. In the same spirit as the change done by
Eric Dumazet on csum_replace2(), this patch rewrites inet_proto_csum_replace4()
taking into account RFC1624.
I spotted during a NATted tcp transfert that csum_partial() is one of top 5
consuming functions (around 8%), and the second user of csum_partial() is
inet_proto_csum_replace4().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While profiling TCP stack, I noticed one useless atomic operation
in tcp_sendmsg(), caused by skb_header_release().
It turns out all current skb_header_release() users have a fresh skb,
that no other user can see, so we can avoid one atomic operation.
Introduce __skb_header_release() to clearly document this.
This gave me a 1.5 % improvement on TCP_RR workload.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No caller or macro uses the return value so make all
the functions return void.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The send_check logic was only interesting in cases of TCP offload and
UDP UFO where the checksum needed to be initialized to the pseudo
header checksum. Now we've moved that logic into the related
gso_segment functions so gso_send_check is no longer needed.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|