summaryrefslogtreecommitdiff
path: root/net/mac80211/wme.h
AgeCommit message (Collapse)Author
2012-06-20mac80211: save wmm_acm per sdataYoni Divinsky
Save and configure the wmm_acm per sdata, rather than per hardware. If wmm_acm is saved per hardware when running two interfaces simultaneously on the same hardware one interface's wmm policy will be affected by the other interface. Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-04-10mac80211: make ieee80211_downgrade_queue staticJohannes Berg
There's no reason for it to not be static. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-11-28mac80211: fix forwarded mesh frame queue mappingThomas Pedersen
We can't rely on ieee80211_select_queue() to do its job at this point since the skb->protocol is not yet known. Instead, factor out and reuse the queue mapping logic for injected frames. Also, to mitigate congestion, forwarded frames should be dropped if the outgoing queue was stopped. This was not correctly implemented as we were not checking the right queue. Furthermore, we were dropping frames that had arrived to their destination if that queue was stopped. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-14mac80211: Mesh data frames must have the QoS headerJavier Cardona
Per sec 7.1.3.5 of draft 12.0 of 802.11s, mesh frames indicate the presence of the mesh control header in their QoS header. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-27wireless: unify QoS control field definitionsJohannes Berg
Move all that mac80211 has into the generic ieee80211.h header file and use them. At the same time move them from mask+shift to just bits and rename them for consistent names. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-05mac80211: fix skb buffering issueJohannes Berg
Since I removed the master netdev, we've been keeping internal queues only, and even before that we never told the networking stack above the virtual interfaces about congestion. This means that packets are queued in mac80211 and the upper layers never know, possibly leading to memory exhaustion and other problems. This patch makes all interfaces multiqueue and uses ndo_select_queue to put the packets into queues per AC. Additionally, when the driver stops a queue, we now stop all corresponding queues for the virtual interfaces as well. The injection case will use VO by default for non-data frames, and BE for data frames, but downgrade any data frames according to ACM. It needs to be fleshed out in the future to allow chosing the queue/AC in radiotap. Reported-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org [2.6.32] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-24mac80211: remove master netdevJohannes Berg
With the internal 'pending' queue system in place, we can simply put packets there instead of pushing them off to the master dev, getting rid of the master interface completely. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27mac80211: fix aggregation for hardware with ampdu queuesJohannes Berg
Hardware with AMPDU queues currently has broken aggregation. This patch fixes it by making all A-MPDUs go over the regular AC queues, but keeping track of the hardware queues in mac80211. As a first rough version, it actually stops the AC queue for extended periods of time, which can be removed by adding buffering internal to mac80211, but is currently not a huge problem because people rarely use multiple TIDs that are in the same AC (and iwlwifi currently doesn't operate as AP). This is a short-term fix, my current medium-term plan, which I hope to execute soon as well, but am not sure can finish before .30, looks like this: 1) rework the internal queuing layer in mac80211 that we use for fragments if the driver stopped queue in the middle of a fragmented frame to be able to queue more frames at once (rather than just a single frame with its fragments) 2) instead of stopping the entire AC queue, queue up the frames in a per-station/per-TID queue during aggregation session initiation, when the session has come up take all those frames and put them onto the queue from 1) 3) push the ampdu queue layer abstraction this patch introduces in mac80211 into the driver, and remove the virtual queue stuff from mac80211 again This plan will probably also affect ath9k in that mac80211 queues the frames instead of passing them down, even when there are no ampdu queues. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-15mac80211: clean up some commentsJohannes Berg
Some comments refer to 80211.o or similar; also remove a comment about implementing fragments better, we really have better things to do. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-08-22mac80211: wme.h remove unused QOS_CONTROL_LENHarvey Harrison
linux/ieee80211.h now has IEEE80211_QOS_CTL_LEN for this purpose. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-07-17mac80211: Reimplement WME using ->select_queue().David S. Miller
The only behavior change is that we do not drop packets under any circumstances. If that is absolutely needed, we could easily add it back. With cleanups and help from Johannes Berg. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-08mac80211: move QOS control helpers into ieee80211.hHarvey Harrison
Also remove the WLAN_IS_QOS_DATA inline after removing the last two users. This starts moving away from using rx->fc to using the header frame_control directly. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-05-21mac80211: use multi-queue master netdeviceJohannes Berg
This patch updates mac80211 and drivers to be multi-queue aware and use that instead of the internal queue mapping. Also does a number of cleanups in various pieces of the code that fall out and reduces internal mac80211 state size. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-02-29mac80211: A-MPDU Tx adding qdisc supportRon Rindjunsky
This patch allows qdisc support in A-MPDU Tx. a method to handle QoS <-> TID switches is present in this patch. Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10[MAC80211]: move QoS rx handlers into rx.cJohannes Berg
This patch moves the QoS handlers into rx.c making it possible to compile wme.c only when NET_SCHED is defined. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jiri Benc <jbenc@suse.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-05-05[MAC80211]: Add mac80211 wireless stack.Jiri Benc
Add mac80211, the IEEE 802.11 software MAC layer. Signed-off-by: Jiri Benc <jbenc@suse.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>