| Age | Commit message (Collapse) | Author |
|---|
|
Jumping between chains doesn't mix well with flush ruleset. Rules
from a different chain and set elements may still refer to us.
[ 353.373791] ------------[ cut here ]------------
[ 353.373845] kernel BUG at net/netfilter/nf_tables_api.c:1159!
[ 353.373896] invalid opcode: 0000 [#1] SMP
[ 353.373942] Modules linked in: intel_powerclamp uas iwldvm iwlwifi
[ 353.374017] CPU: 0 PID: 6445 Comm: 31c3.nft Not tainted 3.18.0 #98
[ 353.374069] Hardware name: LENOVO 5129CTO/5129CTO, BIOS 6QET47WW (1.17 ) 07/14/2010
[...]
[ 353.375018] Call Trace:
[ 353.375046] [<ffffffff81964c31>] ? nf_tables_commit+0x381/0x540
[ 353.375101] [<ffffffff81949118>] nfnetlink_rcv+0x3d8/0x4b0
[ 353.375150] [<ffffffff81943fc5>] netlink_unicast+0x105/0x1a0
[ 353.375200] [<ffffffff8194438e>] netlink_sendmsg+0x32e/0x790
[ 353.375253] [<ffffffff818f398e>] sock_sendmsg+0x8e/0xc0
[ 353.375300] [<ffffffff818f36b9>] ? move_addr_to_kernel.part.20+0x19/0x70
[ 353.375357] [<ffffffff818f44f9>] ? move_addr_to_kernel+0x19/0x30
[ 353.375410] [<ffffffff819016d2>] ? verify_iovec+0x42/0xd0
[ 353.375459] [<ffffffff818f3e10>] ___sys_sendmsg+0x3f0/0x400
[ 353.375510] [<ffffffff810615fa>] ? native_sched_clock+0x2a/0x90
[ 353.375563] [<ffffffff81176697>] ? acct_account_cputime+0x17/0x20
[ 353.375616] [<ffffffff8110dc78>] ? account_user_time+0x88/0xa0
[ 353.375667] [<ffffffff818f4bbd>] __sys_sendmsg+0x3d/0x80
[ 353.375719] [<ffffffff81b184f4>] ? int_check_syscall_exit_work+0x34/0x3d
[ 353.375776] [<ffffffff818f4c0d>] SyS_sendmsg+0xd/0x20
[ 353.375823] [<ffffffff81b1826d>] system_call_fastpath+0x16/0x1b
Release objects in this order: rules -> sets -> chains -> tables, to
make sure no references to chains are held anymore.
Reported-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.biz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Relax the checking that was introduced in 97840cb ("netfilter:
nfnetlink: fix insufficient validation in nfnetlink_bind") when the
subscription bitmask is used. Existing userspace code code may request
to listen to all of the existing netlink groups by setting an all to one
subscription group bitmask. Netlink already validates subscription via
setsockopt() for us.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Make sure there is enough room for the nfnetlink header in the
netlink messages that are part of the batch. There is a similar
check in netlink_rcv_skb().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Commit 5195c14c8b27c ("netfilter: conntrack: fix race in
__nf_conntrack_confirm against get_next_corpse") aimed to resolve the
race condition between the confirmation (packet path) and the flush
command (from control plane). However, it introduced a crash when
several packets race to add a new conntrack, which seems easier to
reproduce when nf_queue is in place.
Fix this race, in __nf_conntrack_confirm(), by removing the CT
from unconfirmed list before checking the DYING bit. In case
race occured, re-add the CT to the dying list
This patch also changes the verdict from NF_ACCEPT to NF_DROP when
we lose race. Basically, the confirmation happens for the first packet
that we see in a flow. If you just invoked conntrack -F once (which
should be the common case), then this is likely to be the first packet
of the flow (unless you already called flush anytime soon in the past).
This should be hard to trigger, but better drop this packet, otherwise
we leave things in inconsistent state since the destination will likely
reply to this packet, but it will find no conntrack, unless the origin
retransmits.
The change of the verdict has been discussed in:
https://www.marc.info/?l=linux-netdev&m=141588039530056&w=2
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Make sure this fetches 16-bits port data from the register.
Remove casting to make sparse happy, not needed anymore.
Signed-off-by: leroy christophe <christophe.leroy@c-s.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs-next into ipvs-next
Simon Horman says:
====================
Second round of IPVS Updates for v3.19
please consider these IPVS updates for v3.19 or alternatively v3.20.
The single patch in this series fixes a long standing bug that
has not caused any trouble and thus is not being prioritised as a fix.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently, searching for a socket to add a reference to is not
synchronized with deletion of sockets. This can result in use
after free if there is another operation that is removing a
socket at the same time. Solving this requires both holding the
appropriate lock and checking the refcount to ensure that it
has not already hit zero.
Inspired by a related (but not exactly the same) issue in the
VXLAN driver.
Fixes: 0b5e8b8e ("net: Add Geneve tunneling protocol driver")
CC: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sockets aren't currently removed from the the global list when
they are destroyed. In addition, offload handlers need to be cleaned
up as well.
Fixes: 0b5e8b8e ("net: Add Geneve tunneling protocol driver")
CC: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
available
Each mmap Netlink frame contains a status field which indicates
whether the frame is unused, reserved, contains data or needs to
be skipped. Both loads and stores may not be reordeded and must
complete before the status field is changed and another CPU might
pick up the frame for use. Use an smp_mb() to cover needs of both
types of callers to netlink_set_status(), callers which have been
reading data frame from the frame, and callers which have been
filling or releasing and thus writing to the frame.
- Example code path requiring a smp_rmb():
memcpy(skb->data, (void *)hdr + NL_MMAP_HDRLEN, hdr->nm_len);
netlink_set_status(hdr, NL_MMAP_STATUS_UNUSED);
- Example code path requiring a smp_wmb():
hdr->nm_uid = from_kuid(sk_user_ns(sk), NETLINK_CB(skb).creds.uid);
hdr->nm_gid = from_kgid(sk_user_ns(sk), NETLINK_CB(skb).creds.gid);
netlink_frame_flush_dcache(hdr);
netlink_set_status(hdr, NL_MMAP_STATUS_VALID);
Fixes: f9c228 ("netlink: implement memory mapped recvmsg()")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Checking the file f_count and the nlk->mapped count is not completely
sufficient to prevent the mmap'd area contents from changing from
under us during netlink mmap sendmsg() operations.
Be careful to sample the header's length field only once, because this
could change from under us as well.
Fixes: 5fd96123ee19 ("netlink: implement memory mapped sendmsg()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
|
|
The current implementations all use dev_uc_add_excl() and such whose API
doesn't support vlans, so we can't make it with NICs HW for now.
Fixes: f6f6424ba773 ('net: make vid as a parameter for ndo_fdb_add/ndo_fdb_del')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The encap->type comes straight from Netlink. Validate it against
max supported encap types just like ip_encap_hlen() already does.
Fixes: a8c5f9 ("ip_tunnel: Ops registration for secondary encap (fou, gue)")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The symbols are exported and could be used by external modules.
Fixes: a8c5f9 ("ip_tunnel: Ops registration for secondary encap (fou, gue)")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-12-16
Please pull this batch of fixes intended for the 3.19 stream!
For the Bluetooth bits, Johan says:
"The patches consist of:
- Coccinelle warning fix
- hci_dev_lock/unlock fixes
- Fixes for pending mgmt command handling
- Fixes for properly following the force_lesc_support switch
- Fix for a Microsoft branded Broadcom adapter
- New device id for Atheros AR3012
- Fix for BR/EDR Secure Connections enabling"
Along with that...
Brian Norris avoids leaking some kernel memory contents via printk in brcmsmac.
Julia Lawall corrects some misspellings in a few drivers.
Larry Finger gives us one more rtlwifi fix to correct a porting oversight.
Wei Yongjun fixes a sparse warning in rtlwifi.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
|
|
net/rds/message.c: In function ‘rds_message_inc_copy_to_user’:
net/rds/message.c:328: warning: comparison of distinct pointer types lacks a cast
Use min_t(unsigned long, ...) like is done in
rds_message_copy_from_user().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NBMA GRE tunnels temporarily push GRE header that contain the
per-packet NBMA destination on the skb via header ops early in xmit
path. It is the later pulled before the real GRE header is constructed.
The inner mac was thus set differently in nbma case: the GRE header
has been pushed by neighbor layer, and mac header points to beginning
of the temporary gre header (set by dev_queue_xmit).
Now that the offloads expect mac header to point to the gre payload,
fix the xmit patch to:
- pull first the temporary gre header away
- and reset mac header to point to gre payload
This fixes tso to work again with nbma tunnels.
Fixes: 14051f0452a2 ("gre: Use inner mac length when computing tunnel length")
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: Tom Herbert <therbert@google.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
Pull crypto update from Herbert Xu:
- The crypto API is now documented :)
- Disallow arbitrary module loading through crypto API.
- Allow get request with empty driver name through crypto_user.
- Allow speed testing of arbitrary hash functions.
- Add caam support for ctr(aes), gcm(aes) and their derivatives.
- nx now supports concurrent hashing properly.
- Add sahara support for SHA1/256.
- Add ARM64 version of CRC32.
- Misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (77 commits)
crypto: tcrypt - Allow speed testing of arbitrary hash functions
crypto: af_alg - add user space interface for AEAD
crypto: qat - fix problem with coalescing enable logic
crypto: sahara - add support for SHA1/256
crypto: sahara - replace tasklets with kthread
crypto: sahara - add support for i.MX53
crypto: sahara - fix spinlock initialization
crypto: arm - replace memset by memzero_explicit
crypto: powerpc - replace memset by memzero_explicit
crypto: sha - replace memset by memzero_explicit
crypto: sparc - replace memset by memzero_explicit
crypto: algif_skcipher - initialize upon init request
crypto: algif_skcipher - removed unneeded code
crypto: algif_skcipher - Fixed blocking recvmsg
crypto: drbg - use memzero_explicit() for clearing sensitive data
crypto: drbg - use MODULE_ALIAS_CRYPTO
crypto: include crypto- module prefix in template
crypto: user - add MODULE_ALIAS
crypto: sha-mb - remove a bogus NULL check
crytpo: qat - Fix 64 bytes requests
...
|
|
This patch addresses an issue with the level compression of the fib_trie.
Specifically in the case of adding a new leaf that triggers a new node to
be added that takes the place of the old node. The result is a trie where
the 1 child tnode is on one side and one leaf is on the other which gives
you a very deep trie. Below is the script I used to generate a trie on
dummy0 with a 10.X.X.X family of addresses.
ip link add type dummy
ipval=184549374
bit=2
for i in `seq 1 23`
do
ifconfig dummy0:$bit $ipval/8
ipval=`expr $ipval - $bit`
bit=`expr $bit \* 2`
done
cat /proc/net/fib_triestat
Running the script before the patch:
Local:
Aver depth: 10.82
Max depth: 23
Leaves: 29
Prefixes: 30
Internal nodes: 27
1: 26 2: 1
Pointers: 56
Null ptrs: 1
Total size: 5 kB
After applying the patch and repeating:
Local:
Aver depth: 4.72
Max depth: 9
Leaves: 29
Prefixes: 30
Internal nodes: 12
1: 3 2: 2 3: 7
Pointers: 70
Null ptrs: 30
Total size: 4 kB
What this fix does is start the rebalance at the newly created tnode
instead of at the parent tnode. This way if there is a gap between the
parent and the new node it doesn't prevent the new tnode from being
coalesced with any pre-existing nodes that may have been pushed into one
of the new nodes child branches.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the real device can segment packets by software, a vlan device
can set TSO/UFO even when the real device doesn't have those features.
Unlike GSO, this allows packets to be segmented after Qdisc.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an adapter is removed (hci_unregister_dev) any pending mgmt
commands for that adapter should get the appropriate INVALID_INDEX
response. Since hci_unregister_dev() calls hci_dev_do_close() first
that'd so far have caused "not powered" responses to be sent.
Skipping the HCI_UNREGISTER case in mgmt_powered() is also not a
solution since before reaching the mgmt_index_removed() stage any
hci_conn callbacks (e.g. used by pairing) will get called, thereby
causing "disconnected" status responses to be sent.
The fix that covers all scenarios is to handle both INVALID_INDEX and
NOT_POWERED responses through the mgmt_powered() function. The
INVALID_INDEX response sending from mgmt_index_removed() is left
untouched since there are a couple of places not related to powering off
or removing an adapter that call it (e.g. configuring a new bdaddr).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
If we're in the AUTO_OFF stage the powered_update_hci() function is
responsible for doing the updates to the HCI state that were not done
during the actual mgmt command handlers. One of the updates needing done
is for BR/EDR SC support. This patch adds the missing HCI command for SC
support to the powered_update_hci() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In case we cannot attach to our slave netdevice PHY, error out and
propagate that error up to the caller: dsa_slave_create().
Fixes: 0d8bcdd383b8 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Andrey Volkov <andrey.volkov@nexvision.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case there is no PHY at the designated address on the internal
switch, we would basically de-reference a null pointer here:
dsa_slave_phy_setup(...)
{
p->phy = ds->slave_mii_bus->phy_map[p->port];
phy_connect_direct(slave_dev, p->phy, dsa_slave_adjust_link,
^------
This can be triggered when the platform configuration (platform_data or
Device Tree) indicates there should be a PHY device at this address, but
the HW is non-responsive, such that we cannot attach a PHY device at
this specific location.
Fix this by checking the return value prior to calling
phy_connect_direct().
CC: Andrew Lunn <andrew@lunn.ch>
Fixes: b31f65fb4383 ("net: dsa: slave: Fix autoneg for phys on switch MDIO bus")
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Andrey Volkov <andrey.volkov@nexvision.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
|
|
Pull virtio updates from Michael Tsirkin:
"virtio: virtio 1.0 support, misc patches
This adds a lot of infrastructure for virtio 1.0 support. Notable
missing pieces: virtio pci, virtio balloon (needs spec extension),
vhost scsi.
Plus, there are some minor fixes in a couple of places.
Note: some net drivers are affected by these patches. David said he's
fine with merging these patches through my tree.
Rusty's on vacation, he acked using my tree for these, too"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (70 commits)
virtio_ccw: finalize_features error handling
virtio_ccw: future-proof finalize_features
virtio_pci: rename virtio_pci -> virtio_pci_common
virtio_pci: update file descriptions and copyright
virtio_pci: split out legacy device support
virtio_pci: setup config vector indirectly
virtio_pci: setup vqs indirectly
virtio_pci: delete vqs indirectly
virtio_pci: use priv for vq notification
virtio_pci: free up vq->priv
virtio_pci: fix coding style for structs
virtio_pci: add isr field
virtio: drop legacy_only driver flag
virtio_balloon: drop legacy_only driver flag
virtio_ccw: rev 1 devices set VIRTIO_F_VERSION_1
virtio: allow finalize_features to fail
virtio_ccw: legacy: don't negotiate rev 1/features
virtio: add API to detect legacy devices
virtio_console: fix sparse warnings
vhost: remove unnecessary forward declarations in vhost.h
...
|
|
This patch moves the mgmt_powered() notification earlier in the
hci_dev_do_close() function. This way the correct "not powered" error
gets passed to any pending mgmt commands. Without the patch the pending
commands would instead get a misleading "disconnected" response when
powering down the adapter.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The pairing_complete() function is used as a pending mgmt command
cmd_complete callback. The expectation of such functions is that they
are not responsible themselves for calling mgmt_pending_remove(). This
patch fixes the incorrect mgmt_pending_remove() call in
pairing_complete() and adds it to the appropriate changes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The pairing_complete() function relies on a hci_conn reference to be
able to access the hci_conn object. It should therefore only release
this reference once it's done accessing the object, i.e. at the end of
the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Read Page Scan Activity and Read Page Scan Type commands are not
supported by all controllers. Move the execution of both commands
into the 3rd phase of the init procedure. And then check the bit
mask of supported commands before adding them to the init sequence.
With this re-ordering of the init sequence, the extra check for
AVM BlueFritz! controllers is no longer needed. They will report
that these two commands are not supported.
This fixes an issue with the Microsoft Corp. Wireless Transceiver
for Bluetooth 2.0 (ID 045e:009c).
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
mgmt_pending_remove() should be called with hci_dev_lock protection and
all hci_event.c functions which calls mgmt_complete() (which eventually
calls mgmt_pending_remove()) should hold the lock.
So this patch fixes the same
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
mgmt_pending_remove() should be called with hci_dev_lock protection
and currently the rule to take dev lock is that all mgmt req_complete
functions should take dev lock. So this patch fixes the same in the
missing functions
Without this patch there is a chance of invalid memory access while
accessing the mgmt_pending list like below
bluetoothd: 392] [0] Backtrace:
bluetoothd: 392] [0] [<c04ec770>] (pending_eir_or_class+0x0/0x68) from [<c04f1830>] (add_uuid+0x34/0x1c4)
bluetoothd: 392] [0] [<c04f17fc>] (add_uuid+0x0/0x1c4) from [<c04f3cc4>] (mgmt_control+0x204/0x274)
bluetoothd: 392] [0] [<c04f3ac0>] (mgmt_control+0x0/0x274) from [<c04f609c>] (hci_sock_sendmsg+0x80/0x308)
bluetoothd: 392] [0] [<c04f601c>] (hci_sock_sendmsg+0x0/0x308) from [<c03d4d68>] (sock_aio_write+0x144/0x174)
bluetoothd: 392] [0] r8:00000000 r7 7c1be90 r6 7c1be18 r5:00000017 r4 a90ea80
bluetoothd: 392] [0] [<c03d4c24>] (sock_aio_write+0x0/0x174) from [<c00e2d4c>] (do_sync_write+0xb0/0xe0)
bluetoothd: 392] [0] [<c00e2c9c>] (do_sync_write+0x0/0xe0) from [<c00e371c>] (vfs_write+0x134/0x13c)
bluetoothd: 392] [0] r8:00000000 r7 7c1bf70 r6:beeca5c8 r5:00000017 r4 7c05900
bluetoothd: 392] [0] [<c00e35e8>] (vfs_write+0x0/0x13c) from [<c00e3910>] (sys_write+0x44/0x70)
bluetoothd: 392] [0] r8:00000000 r7:00000004 r6:00000017 r5:beeca5c8 r4 7c05900
bluetoothd: 392] [0] [<c00e38cc>] (sys_write+0x0/0x70) from [<c000e3c0>] (ret_fast_syscall+0x0/0x30)
bluetoothd: 392] [0] r9 7c1a000 r8:c000e568 r6:400b5f10 r5:403896d8 r4:beeca604
bluetoothd: 392] [0] Code: e28cc00c e152000c 0a00000f e3a00001 (e1d210b8)
bluetoothd: 392] [0] ---[ end trace 67b6ac67435864c4 ]---
bluetoothd: 392] [0] Kernel panic - not syncing: Fatal exception
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
|
|
0day robot reported the following crash:
[ 21.233581] BUG: unable to handle kernel NULL pointer dereference at 0000000000000007
[ 21.234709] IP: [<ffffffff8156ebda>] sk_attach_bpf+0x39/0xc2
It's due to bpf_prog_get() returning ERR_PTR.
Check it properly.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 89aa075832b0 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce helper macro for_each_cmsghdr as a wrapper of the enumerating
cmsghdr from msghdr, just cleanup.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge first patchbomb from Andrew Morton:
- a few minor cifs fixes
- dma-debug upadtes
- ocfs2
- slab
- about half of MM
- procfs
- kernel/exit.c
- panic.c tweaks
- printk upates
- lib/ updates
- checkpatch updates
- fs/binfmt updates
- the drivers/rtc tree
- nilfs
- kmod fixes
- more kernel/exit.c
- various other misc tweaks and fixes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
exit: pidns: fix/update the comments in zap_pid_ns_processes()
exit: pidns: alloc_pid() leaks pid_namespace if child_reaper is exiting
exit: exit_notify: re-use "dead" list to autoreap current
exit: reparent: call forget_original_parent() under tasklist_lock
exit: reparent: avoid find_new_reaper() if no children
exit: reparent: introduce find_alive_thread()
exit: reparent: introduce find_child_reaper()
exit: reparent: document the ->has_child_subreaper checks
exit: reparent: s/while_each_thread/for_each_thread/ in find_new_reaper()
exit: reparent: fix the cross-namespace PR_SET_CHILD_SUBREAPER reparenting
exit: reparent: fix the dead-parent PR_SET_CHILD_SUBREAPER reparenting
exit: proc: don't try to flush /proc/tgid/task/tgid
exit: release_task: fix the comment about group leader accounting
exit: wait: drop tasklist_lock before psig->c* accounting
exit: wait: don't use zombie->real_parent
exit: wait: cleanup the ptrace_reparented() checks
usermodehelper: kill the kmod_thread_locker logic
usermodehelper: don't use CLONE_VFORK for ____call_usermodehelper()
fs/hfs/catalog.c: fix comparison bug in hfs_cat_keycmp
nilfs2: fix the nilfs_iget() vs. nilfs_new_inode() races
...
|
|
Memory is internally accounted in bytes, using spinlock-protected 64-bit
counters, even though the smallest accounting delta is a page. The
counter interface is also convoluted and does too many things.
Introduce a new lockless word-sized page counter API, then change all
memory accounting over to it. The translation from and to bytes then only
happens when interfacing with userspace.
The removed locking overhead is noticable when scaling beyond the per-cpu
charge caches - on a 4-socket machine with 144-threads, the following test
shows the performance differences of 288 memcgs concurrently running a
page fault benchmark:
vanilla:
18631648.500498 task-clock (msec) # 140.643 CPUs utilized ( +- 0.33% )
1,380,638 context-switches # 0.074 K/sec ( +- 0.75% )
24,390 cpu-migrations # 0.001 K/sec ( +- 8.44% )
1,843,305,768 page-faults # 0.099 M/sec ( +- 0.00% )
50,134,994,088,218 cycles # 2.691 GHz ( +- 0.33% )
<not supported> stalled-cycles-frontend
<not supported> stalled-cycles-backend
8,049,712,224,651 instructions # 0.16 insns per cycle ( +- 0.04% )
1,586,970,584,979 branches # 85.176 M/sec ( +- 0.05% )
1,724,989,949 branch-misses # 0.11% of all branches ( +- 0.48% )
132.474343877 seconds time elapsed ( +- 0.21% )
lockless:
12195979.037525 task-clock (msec) # 133.480 CPUs utilized ( +- 0.18% )
832,850 context-switches # 0.068 K/sec ( +- 0.54% )
15,624 cpu-migrations # 0.001 K/sec ( +- 10.17% )
1,843,304,774 page-faults # 0.151 M/sec ( +- 0.00% )
32,811,216,801,141 cycles # 2.690 GHz ( +- 0.18% )
<not supported> stalled-cycles-frontend
<not supported> stalled-cycles-backend
9,999,265,091,727 instructions # 0.30 insns per cycle ( +- 0.10% )
2,076,759,325,203 branches # 170.282 M/sec ( +- 0.12% )
1,656,917,214 branch-misses # 0.08% of all branches ( +- 0.55% )
91.369330729 seconds time elapsed ( +- 0.45% )
On top of improved scalability, this also gets rid of the icky long long
types in the very heart of memcg, which is great for 32 bit and also makes
the code a lot more readable.
Notable differences between the old and new API:
- res_counter_charge() and res_counter_charge_nofail() become
page_counter_try_charge() and page_counter_charge() resp. to match
the more common kernel naming scheme of try_do()/do()
- res_counter_uncharge_until() is only ever used to cancel a local
counter and never to uncharge bigger segments of a hierarchy, so
it's replaced by the simpler page_counter_cancel()
- res_counter_set_limit() is replaced by page_counter_limit(), which
expects its callers to serialize against themselves
- res_counter_memparse_write_strategy() is replaced by
page_counter_limit(), which rounds down to the nearest page size -
rather than up. This is more reasonable for explicitely requested
hard upper limits.
- to keep charging light-weight, page_counter_try_charge() charges
speculatively, only to roll back if the result exceeds the limit.
Because of this, a failing bigger charge can temporarily lock out
smaller charges that would otherwise succeed. The error is bounded
to the difference between the smallest and the biggest possible
charge size, so for memcg, this means that a failing THP charge can
send base page charges into reclaim upto 2MB (4MB) before the limit
would have been reached. This should be acceptable.
[akpm@linux-foundation.org: add includes for WARN_ON_ONCE and memparse]
[akpm@linux-foundation.org: add includes for WARN_ON_ONCE, memparse, strncmp, and PAGE_SIZE]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS changes from Al Viro:
"First pile out of several (there _definitely_ will be more). Stuff in
this one:
- unification of d_splice_alias()/d_materialize_unique()
- iov_iter rewrite
- killing a bunch of ->f_path.dentry users (and f_dentry macro).
Getting that completed will make life much simpler for
unionmount/overlayfs, since then we'll be able to limit the places
sensitive to file _dentry_ to reasonably few. Which allows to have
file_inode(file) pointing to inode in a covered layer, with dentry
pointing to (negative) dentry in union one.
Still not complete, but much closer now.
- crapectomy in lustre (dead code removal, mostly)
- "let's make seq_printf return nothing" preparations
- assorted cleanups and fixes
There _definitely_ will be more piles"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
copy_from_iter_nocache()
new helper: iov_iter_kvec()
csum_and_copy_..._iter()
iov_iter.c: handle ITER_KVEC directly
iov_iter.c: convert copy_to_iter() to iterate_and_advance
iov_iter.c: convert copy_from_iter() to iterate_and_advance
iov_iter.c: get rid of bvec_copy_page_{to,from}_iter()
iov_iter.c: convert iov_iter_zero() to iterate_and_advance
iov_iter.c: convert iov_iter_get_pages_alloc() to iterate_all_kinds
iov_iter.c: convert iov_iter_get_pages() to iterate_all_kinds
iov_iter.c: convert iov_iter_npages() to iterate_all_kinds
iov_iter.c: iterate_and_advance
iov_iter.c: macros for iterating over iov_iter
kill f_dentry macro
dcache: fix kmemcheck warning in switch_names
new helper: audit_file()
nfsd_vfs_write(): use file_inode()
ncpfs: use file_inode()
kill f_dentry uses
lockd: get rid of ->f_path.dentry->d_sb
...
|
|
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Features:
- NFSv4.2 client support for hole punching and preallocation.
- Further RPC/RDMA client improvements.
- Add more RPC transport debugging tracepoints.
- Add RPC debugging tools in debugfs.
Bugfixes:
- Stable fix for layoutget error handling
- Fix a change in COMMIT behaviour resulting from the recent io code
updates"
* tag 'nfs-for-3.19-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (28 commits)
sunrpc: add a debugfs rpc_xprt directory with an info file in it
sunrpc: add debugfs file for displaying client rpc_task queue
nfs: Add DEALLOCATE support
nfs: Add ALLOCATE support
NFS: Clean up nfs4_init_callback()
NFS: SETCLIENTID XDR buffer sizes are incorrect
SUNRPC: serialize iostats updates
xprtrdma: Display async errors
xprtrdma: Enable pad optimization
xprtrdma: Re-write rpcrdma_flush_cqs()
xprtrdma: Refactor tasklet scheduling
xprtrdma: unmap all FMRs during transport disconnect
xprtrdma: Cap req_cqinit
xprtrdma: Return an errno from rpcrdma_register_external()
nfs: define nfs_inc_fscache_stats and using it as possible
nfs: replace nfs_add_stats with nfs_inc_stats when add one
NFS: Deletion of unnecessary checks before the function call "nfs_put_client"
sunrpc: eliminate RPC_TRACEPOINTS
sunrpc: eliminate RPC_DEBUG
lockd: eliminate LOCKD_DEBUG
...
|
|
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Making things const is a good thing.
(x86-64 defconfig with all irda)
$ size net/irda/built-in.o*
text data bss dec hex filename
109276 1868 244 111388 1b31c net/irda/built-in.o.new
108828 2316 244 111388 1b31c net/irda/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's better when function pointer arrays aren't modifiable.
Net change:
$ size net/llc/built-in.o.*
text data bss dec hex filename
61193 12758 1344 75295 1261f net/llc/built-in.o.new
47113 27030 1344 75487 126df net/llc/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's better when function pointer arrays aren't modifiable.
Net change from original:
$ size net/llc/built-in.o.*
text data bss dec hex filename
61065 12886 1344 75295 1261f net/llc/built-in.o.new
47113 27030 1344 75487 126df net/llc/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's better when function pointer arrays aren't modifiable.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch effectively reverts commit 500f80872645 ("net: ovs: use CRC32
accelerated flow hash if available"), and other remaining arch_fast_hash()
users such as from nfsd via commit 6282cd565553 ("NFSD: Don't hand out
delegations for 30 seconds after recalling them.") where it has been used
as a hash function for bloom filtering.
While we think that these users are actually not much of concern, it has
been requested to remove the arch_fast_hash() library bits that arose
from [1] entirely as per recent discussion [2]. The main argument is that
using it as a hash may introduce bias due to its linearity (see avalanche
criterion) and thus makes it less clear (though we tried to document that)
when this security/performance trade-off is actually acceptable for a
general purpose library function.
Lets therefore avoid any further confusion on this matter and remove it to
prevent any future accidental misuse of it. For the time being, this is
going to make hashing of flow keys a bit more expensive in the ovs case,
but future work could reevaluate a different hashing discipline.
[1] https://patchwork.ozlabs.org/patch/299369/
[2] https://patchwork.ozlabs.org/patch/418756/
Cc: Neil Brown <neilb@suse.de>
Cc: Francesco Fusco <fusco@ntop.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For netlink, we shouldn't be using arch_fast_hash() as a hashing
discipline, but rather jhash() instead.
Since netlink sockets can be opened by any user, a local attacker
would be able to easily create collisions with the DPDK-derived
arch_fast_hash(), which trades off performance for security by
using crc32 CPU instructions on x86_64.
While it might have a legimite use case in other places, it should
be avoided in netlink context, though. As rhashtable's API is very
flexible, we could later on still decide on other hashing disciplines,
if legitimate.
Reference: http://thread.gmane.org/gmane.linux.kernel/1844123
Fixes: e341694e3eb5 ("netlink: Convert netlink_lookup() to use RCU protected hash table")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 908344cdda80 ("tipc: fix bug in multicast congestion handling")
introduced a race in the broadcast link wakeup functionality.
This patch eliminates this broadcast link wakeup race caused by
operation on the wakeup list without proper locking. If this race
hit and corrupted the list all subsequent wakeup messages would be
lost, resulting in a considerable memory leak.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change pulls the core functionality out of __netdev_alloc_skb and
places them in a new function named __alloc_rx_skb. The reason for doing
this is to make these bits accessible to a new function __napi_alloc_skb.
In addition __alloc_rx_skb now has a new flags value that is used to
determine which page frag pool to allocate from. If the SKB_ALLOC_NAPI
flag is set then the NAPI pool is used. The advantage of this is that we
do not have to use local_irq_save/restore when accessing the NAPI pool from
NAPI context.
In my test setup I saw at least 11ns of savings using the napi_alloc_skb
function versus the netdev_alloc_skb function, most of this being due to
the fact that we didn't have to call local_irq_save/restore.
The main use case for napi_alloc_skb would be for things such as copybreak
or page fragment based receive paths where an skb is allocated after the
data has been received instead of before.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch splits the netdev_alloc_frag function up so that it can be used
on one of two page frag pools instead of being fixed on the
netdev_alloc_cache. By doing this we can add a NAPI specific function
__napi_alloc_frag that accesses a pool that is only used from softirq
context. The advantage to this is that we do not need to call
local_irq_save/restore which can be a significant savings.
I also took the opportunity to refactor the core bits that were placed in
__alloc_page_frag. First I updated the allocation to do either a 32K
allocation or an order 0 page. This is based on the changes in commmit
d9b2938aa where it was found that latencies could be reduced in case of
failures. Then I also rewrote the logic to work from the end of the page to
the start. By doing this the size value doesn't have to be used unless we
have run out of space for page fragments. Finally I cleaned up the atomic
bits so that we just do an atomic_sub_and_test and if that returns true then
we set the page->_count via an atomic_set. This way we can remove the extra
conditional for the atomic_read since it would have led to an atomic_inc in
the case of success anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
