From 8934210cfe925f0d3e3089c69e9e88021324801b Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Fri, 7 Aug 2009 08:41:15 +0200 Subject: powerpc/82xx: mgcoge - updated defconfig - add I2C support - add FCC1 and FCC2 support Signed-off-by: Heiko Schocher Signed-off-by: Kumar Gala --- arch/powerpc/configs/mgcoge_defconfig | 86 ++++++++++++++++++++++++++++++++--- 1 file changed, 80 insertions(+), 6 deletions(-) diff --git a/arch/powerpc/configs/mgcoge_defconfig b/arch/powerpc/configs/mgcoge_defconfig index e9491c1c3f31..30b68bfacebf 100644 --- a/arch/powerpc/configs/mgcoge_defconfig +++ b/arch/powerpc/configs/mgcoge_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.31-rc4 -# Wed Jul 29 23:31:51 2009 +# Linux kernel version: 2.6.31-rc5 +# Fri Aug 7 08:19:15 2009 # # CONFIG_PPC64 is not set @@ -158,6 +158,7 @@ CONFIG_BASE_SMALL=0 # CONFIG_MODULES is not set CONFIG_BLOCK=y CONFIG_LBDAF=y +CONFIG_BLK_DEV_BSG=y # CONFIG_BLK_DEV_INTEGRITY is not set # @@ -506,6 +507,7 @@ CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_GPIO=y +CONFIG_OF_I2C=y CONFIG_OF_MDIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y @@ -582,7 +584,8 @@ CONFIG_PHYLIB=y # CONFIG_STE10XP is not set # CONFIG_LSI_ET1011C_PHY is not set CONFIG_FIXED_PHY=y -# CONFIG_MDIO_BITBANG is not set +CONFIG_MDIO_BITBANG=y +# CONFIG_MDIO_GPIO is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_MACE is not set @@ -608,8 +611,8 @@ CONFIG_MII=y # CONFIG_ATL2 is not set CONFIG_FS_ENET=y CONFIG_FS_ENET_HAS_SCC=y -# CONFIG_FS_ENET_HAS_FCC is not set -# CONFIG_FS_ENET_MDIO_FCC is not set +CONFIG_FS_ENET_HAS_FCC=y +CONFIG_FS_ENET_MDIO_FCC=y # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set # CONFIG_TR is not set @@ -680,7 +683,68 @@ CONFIG_HW_RANDOM=y # CONFIG_APPLICOM is not set # CONFIG_RAW_DRIVER is not set CONFIG_DEVPORT=y -# CONFIG_I2C is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# PC SMBus host controller drivers +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_ISCH is not set +# CONFIG_I2C_PIIX4 is not set +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_VIAPRO is not set + +# +# Mac SMBus host controller drivers +# +# CONFIG_I2C_POWERMAC is not set + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_CPM=y +# CONFIG_I2C_DESIGNWARE is not set +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_MPC is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set + +# +# Graphics adapter I2C/DDC channel drivers +# +# CONFIG_I2C_VOODOO3 is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_PCF8575 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set # @@ -699,6 +763,9 @@ CONFIG_GPIOLIB=y # # I2C GPIO expanders: # +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set # # PCI GPIO expanders: @@ -727,7 +794,14 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_TPS65010 is not set +# CONFIG_TWL4030_CORE is not set # CONFIG_MFD_TMIO is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_MFD_PCF50633 is not set +# CONFIG_AB3100_CORE is not set # CONFIG_REGULATOR is not set # CONFIG_MEDIA_SUPPORT is not set -- cgit v1.2.3 From fc4bdb35fba1c8f464fd85b94a5059e752fc85d4 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Fri, 14 Aug 2009 09:38:34 -0500 Subject: powerpc/booke: Move MMUCSR definition into mmu-book3e.h The MMUCSR is now defined as part of the Book-3E architecture so we can move it into mmu-book3e.h and add some of the additional bits defined by the architecture specs. Signed-off-by: Kumar Gala --- arch/powerpc/include/asm/mmu-book3e.h | 12 ++++++++++++ arch/powerpc/include/asm/reg_booke.h | 6 ------ arch/powerpc/mm/tlb_nohash_low.S | 2 -- 3 files changed, 12 insertions(+), 8 deletions(-) diff --git a/arch/powerpc/include/asm/mmu-book3e.h b/arch/powerpc/include/asm/mmu-book3e.h index d74580469361..74695816205c 100644 --- a/arch/powerpc/include/asm/mmu-book3e.h +++ b/arch/powerpc/include/asm/mmu-book3e.h @@ -114,6 +114,18 @@ #define MAS7_RPN 0xFFFFFFFF +/* Bit definitions for MMUCSR0 */ +#define MMUCSR0_TLB1FI 0x00000002 /* TLB1 Flash invalidate */ +#define MMUCSR0_TLB0FI 0x00000004 /* TLB0 Flash invalidate */ +#define MMUCSR0_TLB2FI 0x00000040 /* TLB2 Flash invalidate */ +#define MMUCSR0_TLB3FI 0x00000020 /* TLB3 Flash invalidate */ +#define MMUCSR0_TLBFI (MMUCSR0_TLB0FI | MMUCSR0_TLB1FI | \ + MMUCSR0_TLB2FI | MMUCSR0_TLB3FI) +#define MMUCSR0_TLB0PS 0x00000780 /* TLB0 Page Size */ +#define MMUCSR0_TLB1PS 0x00007800 /* TLB1 Page Size */ +#define MMUCSR0_TLB2PS 0x00078000 /* TLB2 Page Size */ +#define MMUCSR0_TLB3PS 0x00780000 /* TLB3 Page Size */ + /* TLBnCFG encoding */ #define TLBnCFG_N_ENTRY 0x00000fff /* number of entries */ #define TLBnCFG_HES 0x00002000 /* HW select supported */ diff --git a/arch/powerpc/include/asm/reg_booke.h b/arch/powerpc/include/asm/reg_booke.h index 2c9c706e6448..9bb81d99b765 100644 --- a/arch/powerpc/include/asm/reg_booke.h +++ b/arch/powerpc/include/asm/reg_booke.h @@ -430,12 +430,6 @@ #define L2CSR0_L2LOA 0x00000080 /* L2 Cache Lock Overflow Allocate */ #define L2CSR0_L2LO 0x00000020 /* L2 Cache Lock Overflow */ -/* Bit definitions for MMUCSR0 */ -#define MMUCSR0_TLB1FI 0x00000002 /* TLB1 Flash invalidate */ -#define MMUCSR0_TLB0FI 0x00000004 /* TLB0 Flash invalidate */ -#define MMUCSR0_TLB2FI 0x00000040 /* TLB2 Flash invalidate */ -#define MMUCSR0_TLB3FI 0x00000020 /* TLB3 Flash invalidate */ - /* Bit definitions for SGR. */ #define SGR_NORMAL 0 /* Speculative fetching allowed. */ #define SGR_GUARDED 1 /* Speculative fetching disallowed. */ diff --git a/arch/powerpc/mm/tlb_nohash_low.S b/arch/powerpc/mm/tlb_nohash_low.S index 7bcd9fbf6cc6..bbdc5b577b85 100644 --- a/arch/powerpc/mm/tlb_nohash_low.S +++ b/arch/powerpc/mm/tlb_nohash_low.S @@ -124,8 +124,6 @@ _GLOBAL(_tlbil_pid) * to have the larger code path before the _SECTION_ELSE */ -#define MMUCSR0_TLBFI (MMUCSR0_TLB0FI | MMUCSR0_TLB1FI | \ - MMUCSR0_TLB2FI | MMUCSR0_TLB3FI) /* * Flush MMU TLB on the local processor */ -- cgit v1.2.3 From fb8e3e1fe1df963b6c1ab8610682737ccae96ef0 Mon Sep 17 00:00:00 2001 From: Poonam Aggrwal Date: Fri, 7 Aug 2009 21:05:16 +0530 Subject: powerpc/85xx: Add support for P2020RDB board Add support for the P2020RDB reference board from Freescale. Overview of P2020RDB platform - DDR DDR2 1G - NOR Flash 16MByte - NAND Flash 32MByte - 3 Ethernet interfaces 1) etSEC1 - RGMII - connected to a 5 port Vitesse Switch(VSC7385) - Switch is memory mapped through eLBC interface(CS#2) - IRQ1 2) etSEC2 - SGMII - connected to VSC8221 - IRQ2 3) etSEC3 - RGMII - connected to VSC8641 - IRQ3 - 2 1X PCIe interfaces - SD/MMC ,USB - SPI EEPROM - Serial I2C EEPROM Signed-off-by: Poonam Aggrwal Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/p2020rdb.dts | 586 ++++++++++++++++++++++++++++++ arch/powerpc/configs/mpc85xx_defconfig | 1 + arch/powerpc/platforms/85xx/Kconfig | 9 + arch/powerpc/platforms/85xx/Makefile | 3 +- arch/powerpc/platforms/85xx/mpc85xx_rdb.c | 141 +++++++ 5 files changed, 739 insertions(+), 1 deletion(-) create mode 100644 arch/powerpc/boot/dts/p2020rdb.dts create mode 100644 arch/powerpc/platforms/85xx/mpc85xx_rdb.c diff --git a/arch/powerpc/boot/dts/p2020rdb.dts b/arch/powerpc/boot/dts/p2020rdb.dts new file mode 100644 index 000000000000..da4cb0d8d215 --- /dev/null +++ b/arch/powerpc/boot/dts/p2020rdb.dts @@ -0,0 +1,586 @@ +/* + * P2020 RDB Device Tree Source + * + * Copyright 2009 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; +/ { + model = "fsl,P2020"; + compatible = "fsl,P2020RDB"; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + ethernet0 = &enet0; + ethernet1 = &enet1; + ethernet2 = &enet2; + serial0 = &serial0; + serial1 = &serial1; + pci0 = &pci0; + pci1 = &pci1; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,P2020@0 { + device_type = "cpu"; + reg = <0x0>; + next-level-cache = <&L2>; + }; + + PowerPC,P2020@1 { + device_type = "cpu"; + reg = <0x1>; + next-level-cache = <&L2>; + }; + }; + + memory { + device_type = "memory"; + }; + + localbus@ffe05000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,p2020-elbc", "fsl,elbc", "simple-bus"; + reg = <0 0xffe05000 0 0x1000>; + interrupts = <19 2>; + interrupt-parent = <&mpic>; + + /* NOR and NAND Flashes */ + ranges = <0x0 0x0 0x0 0xef000000 0x01000000 + 0x1 0x0 0x0 0xffa00000 0x00040000 + 0x2 0x0 0x0 0xffb00000 0x00020000>; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x1000000>; + bank-width = <2>; + device-width = <1>; + + partition@0 { + /* This location must not be altered */ + /* 256KB for Vitesse 7385 Switch firmware */ + reg = <0x0 0x00040000>; + label = "NOR (RO) Vitesse-7385 Firmware"; + read-only; + }; + + partition@40000 { + /* 256KB for DTB Image */ + reg = <0x00040000 0x00040000>; + label = "NOR (RO) DTB Image"; + read-only; + }; + + partition@80000 { + /* 3.5 MB for Linux Kernel Image */ + reg = <0x00080000 0x00380000>; + label = "NOR (RO) Linux Kernel Image"; + read-only; + }; + + partition@400000 { + /* 11MB for JFFS2 based Root file System */ + reg = <0x00400000 0x00b00000>; + label = "NOR (RW) JFFS2 Root File System"; + }; + + partition@f00000 { + /* This location must not be altered */ + /* 512KB for u-boot Bootloader Image */ + /* 512KB for u-boot Environment Variables */ + reg = <0x00f00000 0x00100000>; + label = "NOR (RO) U-Boot Image"; + read-only; + }; + }; + + nand@1,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p2020-fcm-nand", + "fsl,elbc-fcm-nand"; + reg = <0x1 0x0 0x40000>; + + partition@0 { + /* This location must not be altered */ + /* 1MB for u-boot Bootloader Image */ + reg = <0x0 0x00100000>; + label = "NAND (RO) U-Boot Image"; + read-only; + }; + + partition@100000 { + /* 1MB for DTB Image */ + reg = <0x00100000 0x00100000>; + label = "NAND (RO) DTB Image"; + read-only; + }; + + partition@200000 { + /* 4MB for Linux Kernel Image */ + reg = <0x00200000 0x00400000>; + label = "NAND (RO) Linux Kernel Image"; + read-only; + }; + + partition@600000 { + /* 4MB for Compressed Root file System Image */ + reg = <0x00600000 0x00400000>; + label = "NAND (RO) Compressed RFS Image"; + read-only; + }; + + partition@a00000 { + /* 7MB for JFFS2 based Root file System */ + reg = <0x00a00000 0x00700000>; + label = "NAND (RW) JFFS2 Root File System"; + }; + + partition@1100000 { + /* 15MB for JFFS2 based Root file System */ + reg = <0x01100000 0x00f00000>; + label = "NAND (RW) Writable User area"; + }; + }; + + L2switch@2,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "vitesse-7385"; + reg = <0x2 0x0 0x20000>; + }; + + }; + + soc@ffe00000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "fsl,p2020-immr", "simple-bus"; + ranges = <0x0 0x0 0xffe00000 0x100000>; + bus-frequency = <0>; // Filled out by uboot. + + ecm-law@0 { + compatible = "fsl,ecm-law"; + reg = <0x0 0x1000>; + fsl,num-laws = <12>; + }; + + ecm@1000 { + compatible = "fsl,p2020-ecm", "fsl,ecm"; + reg = <0x1000 0x1000>; + interrupts = <17 2>; + interrupt-parent = <&mpic>; + }; + + memory-controller@2000 { + compatible = "fsl,p2020-memory-controller"; + reg = <0x2000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <18 2>; + }; + + i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + dfsrr; + rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; + }; + + i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + compatible = "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + dfsrr; + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4500 0x100>; + clock-frequency = <0>; + interrupts = <42 2>; + interrupt-parent = <&mpic>; + }; + + serial1: serial@4600 { + cell-index = <1>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4600 0x100>; + clock-frequency = <0>; + interrupts = <42 2>; + interrupt-parent = <&mpic>; + }; + + spi@7000 { + cell-index = <0>; + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,espi"; + reg = <0x7000 0x1000>; + interrupts = <59 0x2>; + interrupt-parent = <&mpic>; + mode = "cpu"; + + fsl_m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,espi-flash"; + reg = <0>; + linux,modalias = "fsl_m25p80"; + modal = "s25sl128b"; + spi-max-frequency = <50000000>; + mode = <0>; + + partition@0 { + /* 512KB for u-boot Bootloader Image */ + reg = <0x0 0x00080000>; + label = "SPI (RO) U-Boot Image"; + read-only; + }; + + partition@80000 { + /* 512KB for DTB Image */ + reg = <0x00080000 0x00080000>; + label = "SPI (RO) DTB Image"; + read-only; + }; + + partition@100000 { + /* 4MB for Linux Kernel Image */ + reg = <0x00100000 0x00400000>; + label = "SPI (RO) Linux Kernel Image"; + read-only; + }; + + partition@500000 { + /* 4MB for Compressed RFS Image */ + reg = <0x00500000 0x00400000>; + label = "SPI (RO) Compressed RFS Image"; + read-only; + }; + + partition@900000 { + /* 7MB for JFFS2 based RFS */ + reg = <0x00900000 0x00700000>; + label = "SPI (RW) JFFS2 RFS"; + }; + }; + }; + + dma@c300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,eloplus-dma"; + reg = <0xc300 0x4>; + ranges = <0x0 0xc100 0x200>; + cell-index = <1>; + dma-channel@0 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupt-parent = <&mpic>; + interrupts = <76 2>; + }; + dma-channel@80 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupt-parent = <&mpic>; + interrupts = <77 2>; + }; + dma-channel@100 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupt-parent = <&mpic>; + interrupts = <78 2>; + }; + dma-channel@180 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupt-parent = <&mpic>; + interrupts = <79 2>; + }; + }; + + gpio: gpio-controller@f000 { + #gpio-cells = <2>; + compatible = "fsl,mpc8572-gpio"; + reg = <0xf000 0x100>; + interrupts = <47 0x2>; + interrupt-parent = <&mpic>; + gpio-controller; + }; + + L2: l2-cache-controller@20000 { + compatible = "fsl,p2020-l2-cache-controller"; + reg = <0x20000 0x1000>; + cache-line-size = <32>; // 32 bytes + cache-size = <0x80000>; // L2,512K + interrupt-parent = <&mpic>; + interrupts = <16 2>; + }; + + dma@21300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,eloplus-dma"; + reg = <0x21300 0x4>; + ranges = <0x0 0x21100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupt-parent = <&mpic>; + interrupts = <20 2>; + }; + dma-channel@80 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupt-parent = <&mpic>; + interrupts = <21 2>; + }; + dma-channel@100 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupt-parent = <&mpic>; + interrupts = <22 2>; + }; + dma-channel@180 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupt-parent = <&mpic>; + interrupts = <23 2>; + }; + }; + + usb@22000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl-usb2-dr"; + reg = <0x22000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <28 0x2>; + phy_type = "ulpi"; + }; + + enet0: ethernet@24000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <0>; + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + ranges = <0x0 0x24000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <29 2 30 2 34 2>; + interrupt-parent = <&mpic>; + fixed-link = <1 1 1000 0 0>; + phy-connection-type = "rgmii-id"; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-mdio"; + reg = <0x520 0x20>; + + phy0: ethernet-phy@0 { + interrupt-parent = <&mpic>; + interrupts = <3 1>; + reg = <0x0>; + }; + phy1: ethernet-phy@1 { + interrupt-parent = <&mpic>; + interrupts = <3 1>; + reg = <0x1>; + }; + }; + }; + + enet1: ethernet@25000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <1>; + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar"; + reg = <0x25000 0x1000>; + ranges = <0x0 0x25000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <35 2 36 2 40 2>; + interrupt-parent = <&mpic>; + tbi-handle = <&tbi0>; + phy-handle = <&phy0>; + phy-connection-type = "sgmii"; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-tbi"; + reg = <0x520 0x20>; + + tbi0: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + }; + + enet2: ethernet@26000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <2>; + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar"; + reg = <0x26000 0x1000>; + ranges = <0x0 0x26000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <31 2 32 2 33 2>; + interrupt-parent = <&mpic>; + phy-handle = <&phy1>; + phy-connection-type = "rgmii-id"; + }; + + sdhci@2e000 { + compatible = "fsl,p2020-esdhc", "fsl,esdhc"; + reg = <0x2e000 0x1000>; + interrupts = <72 0x2>; + interrupt-parent = <&mpic>; + /* Filled in by U-Boot */ + clock-frequency = <0>; + }; + + crypto@30000 { + compatible = "fsl,sec3.1", "fsl,sec3.0", "fsl,sec2.4", + "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0"; + reg = <0x30000 0x10000>; + interrupts = <45 2 58 2>; + interrupt-parent = <&mpic>; + fsl,num-channels = <4>; + fsl,channel-fifo-len = <24>; + fsl,exec-units-mask = <0xbfe>; + fsl,descriptor-types-mask = <0x3ab0ebf>; + }; + + mpic: pic@40000 { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x40000 0x40000>; + compatible = "chrp,open-pic"; + device_type = "open-pic"; + }; + + msi@41600 { + compatible = "fsl,p2020-msi", "fsl,mpic-msi"; + reg = <0x41600 0x80>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 + 0xe1 0 + 0xe2 0 + 0xe3 0 + 0xe4 0 + 0xe5 0 + 0xe6 0 + 0xe7 0>; + interrupt-parent = <&mpic>; + }; + + global-utilities@e0000 { //global utilities block + compatible = "fsl,p2020-guts"; + reg = <0xe0000 0x1000>; + fsl,has-rstcr; + }; + }; + + pci0: pcie@ffe09000 { + compatible = "fsl,mpc8548-pcie"; + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0 0xffe09000 0 0x1000>; + bus-range = <0 255>; + ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000 + 0x1000000 0x0 0x00000000 0 0xffc30000 0x0 0x10000>; + clock-frequency = <33333333>; + interrupt-parent = <&mpic>; + interrupts = <25 2>; + pcie@0 { + reg = <0x0 0x0 0x0 0x0 0x0>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + ranges = <0x2000000 0x0 0xa0000000 + 0x2000000 0x0 0xa0000000 + 0x0 0x20000000 + + 0x1000000 0x0 0x0 + 0x1000000 0x0 0x0 + 0x0 0x100000>; + }; + }; + + pci1: pcie@ffe0a000 { + compatible = "fsl,mpc8548-pcie"; + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0 0xffe0a000 0 0x1000>; + bus-range = <0 255>; + ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000 + 0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>; + clock-frequency = <33333333>; + interrupt-parent = <&mpic>; + interrupts = <26 2>; + pcie@0 { + reg = <0x0 0x0 0x0 0x0 0x0>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + ranges = <0x2000000 0x0 0xc0000000 + 0x2000000 0x0 0xc0000000 + 0x0 0x20000000 + + 0x1000000 0x0 0x0 + 0x1000000 0x0 0x0 + 0x0 0x100000>; + }; + }; +}; diff --git a/arch/powerpc/configs/mpc85xx_defconfig b/arch/powerpc/configs/mpc85xx_defconfig index ada595898af1..ee6acc6557f8 100644 --- a/arch/powerpc/configs/mpc85xx_defconfig +++ b/arch/powerpc/configs/mpc85xx_defconfig @@ -203,6 +203,7 @@ CONFIG_MPC85xx_CDS=y CONFIG_MPC85xx_MDS=y CONFIG_MPC8536_DS=y CONFIG_MPC85xx_DS=y +CONFIG_MPC85xx_RDB=y CONFIG_SOCRATES=y CONFIG_KSI8560=y # CONFIG_XES_MPC85xx is not set diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig index a9b416688975..d3a975e8fd3e 100644 --- a/arch/powerpc/platforms/85xx/Kconfig +++ b/arch/powerpc/platforms/85xx/Kconfig @@ -55,6 +55,15 @@ config MPC85xx_DS help This option enables support for the MPC85xx DS (MPC8544 DS) board +config MPC85xx_RDB + bool "Freescale MPC85xx RDB" + select PPC_I8259 + select DEFAULT_UIMAGE + select FSL_ULI1575 + select SWIOTLB + help + This option enables support for the MPC85xx RDB (P2020 RDB) board + config SOCRATES bool "Socrates" select DEFAULT_UIMAGE diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile index 835733f2b12c..9098aea0cf32 100644 --- a/arch/powerpc/platforms/85xx/Makefile +++ b/arch/powerpc/platforms/85xx/Makefile @@ -9,10 +9,11 @@ obj-$(CONFIG_MPC85xx_CDS) += mpc85xx_cds.o obj-$(CONFIG_MPC8536_DS) += mpc8536_ds.o obj-$(CONFIG_MPC85xx_DS) += mpc85xx_ds.o obj-$(CONFIG_MPC85xx_MDS) += mpc85xx_mds.o +obj-$(CONFIG_MPC85xx_RDB) += mpc85xx_rdb.o obj-$(CONFIG_STX_GP3) += stx_gp3.o obj-$(CONFIG_TQM85xx) += tqm85xx.o obj-$(CONFIG_SBC8560) += sbc8560.o obj-$(CONFIG_SBC8548) += sbc8548.o obj-$(CONFIG_SOCRATES) += socrates.o socrates_fpga_pic.o obj-$(CONFIG_KSI8560) += ksi8560.o -obj-$(CONFIG_XES_MPC85xx) += xes_mpc85xx.o \ No newline at end of file +obj-$(CONFIG_XES_MPC85xx) += xes_mpc85xx.o diff --git a/arch/powerpc/platforms/85xx/mpc85xx_rdb.c b/arch/powerpc/platforms/85xx/mpc85xx_rdb.c new file mode 100644 index 000000000000..c8468de4acf6 --- /dev/null +++ b/arch/powerpc/platforms/85xx/mpc85xx_rdb.c @@ -0,0 +1,141 @@ +/* + * MPC85xx RDB Board Setup + * + * Copyright 2009 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +#undef DEBUG + +#ifdef DEBUG +#define DBG(fmt, args...) printk(KERN_ERR "%s: " fmt, __func__, ## args) +#else +#define DBG(fmt, args...) +#endif + + +void __init mpc85xx_rdb_pic_init(void) +{ + struct mpic *mpic; + struct resource r; + struct device_node *np; + + np = of_find_node_by_type(NULL, "open-pic"); + if (np == NULL) { + printk(KERN_ERR "Could not find open-pic node\n"); + return; + } + + if (of_address_to_resource(np, 0, &r)) { + printk(KERN_ERR "Failed to map mpic register space\n"); + of_node_put(np); + return; + } + + mpic = mpic_alloc(np, r.start, + MPIC_PRIMARY | MPIC_WANTS_RESET | + MPIC_BIG_ENDIAN | MPIC_BROKEN_FRR_NIRQS | + MPIC_SINGLE_DEST_CPU, + 0, 256, " OpenPIC "); + + BUG_ON(mpic == NULL); + of_node_put(np); + + mpic_init(mpic); + +} + +/* + * Setup the architecture + */ +#ifdef CONFIG_SMP +extern void __init mpc85xx_smp_init(void); +#endif +static void __init mpc85xx_rdb_setup_arch(void) +{ +#ifdef CONFIG_PCI + struct device_node *np; +#endif + + if (ppc_md.progress) + ppc_md.progress("mpc85xx_rdb_setup_arch()", 0); + +#ifdef CONFIG_PCI + for_each_node_by_type(np, "pci") { + if (of_device_is_compatible(np, "fsl,mpc8548-pcie")) + fsl_add_bridge(np, 0); + } + +#endif + +#ifdef CONFIG_SMP + mpc85xx_smp_init(); +#endif + + printk(KERN_INFO "MPC85xx RDB board from Freescale Semiconductor\n"); +} + +static struct of_device_id __initdata mpc85xxrdb_ids[] = { + { .type = "soc", }, + { .compatible = "soc", }, + { .compatible = "simple-bus", }, + { .compatible = "gianfar", }, + {}, +}; + +static int __init mpc85xxrdb_publish_devices(void) +{ + return of_platform_bus_probe(NULL, mpc85xxrdb_ids, NULL); +} +machine_device_initcall(p2020_rdb, mpc85xxrdb_publish_devices); + +/* + * Called very early, device-tree isn't unflattened + */ +static int __init p2020_rdb_probe(void) +{ + unsigned long root = of_get_flat_dt_root(); + + if (of_flat_dt_is_compatible(root, "fsl,P2020RDB")) + return 1; + return 0; +} + +define_machine(p2020_rdb) { + .name = "P2020 RDB", + .probe = p2020_rdb_probe, + .setup_arch = mpc85xx_rdb_setup_arch, + .init_IRQ = mpc85xx_rdb_pic_init, +#ifdef CONFIG_PCI + .pcibios_fixup_bus = fsl_pcibios_fixup_bus, +#endif + .get_irq = mpic_get_irq, + .restart = fsl_rstcr_restart, + .calibrate_decr = generic_calibrate_decr, + .progress = udbg_progress, +}; -- cgit v1.2.3 From 4de124446b4d68edd6cb747495234be915d56a29 Mon Sep 17 00:00:00 2001 From: Liang Li Date: Wed, 12 Aug 2009 09:34:28 -0400 Subject: powerpc/83xx: Remove second USB node from SBC834x DTS Since only one of the SoC USB devices is brought out to a physical connector on the board, remove the 2nd (USB-DR) node from the DTS. Having it present and USB enabled will cause a hang at boot. Signed-off-by: Liang Li Signed-off-by: Yang Shi Signed-off-by: Paul Gortmaker Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/sbc8349.dts | 12 ------------ 1 file changed, 12 deletions(-) diff --git a/arch/powerpc/boot/dts/sbc8349.dts b/arch/powerpc/boot/dts/sbc8349.dts index 2d9fa68f641c..d93e5beab731 100644 --- a/arch/powerpc/boot/dts/sbc8349.dts +++ b/arch/powerpc/boot/dts/sbc8349.dts @@ -146,18 +146,6 @@ phy_type = "ulpi"; port0; }; - /* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */ - usb@23000 { - device_type = "usb"; - compatible = "fsl-usb2-dr"; - reg = <0x23000 0x1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupt-parent = <&ipic>; - interrupts = <38 0x8>; - dr_mode = "otg"; - phy_type = "ulpi"; - }; enet0: ethernet@24000 { #address-cells = <1>; -- cgit v1.2.3 From 31ff09b7a60bbc80b5df941ec1a12502861b4da9 Mon Sep 17 00:00:00 2001 From: Liang Li Date: Wed, 12 Aug 2009 09:34:29 -0400 Subject: powerpc/83xx: Add localbus node and MTD partitions for SBC834x There is 8MB flash, 8kB EEPROM and 128MB SDRAM on the sbc834x local bus, so add a localbus node in DTS with MTD partitions. The recent U-boot commit fe613cdd4eb moves u-boot to the beginning of flash, hence the legacy label on the partition at the end of flash. Signed-off-by: Liang Li Signed-off-by: Yang Shi Signed-off-by: Paul Gortmaker Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/sbc8349.dts | 40 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+) diff --git a/arch/powerpc/boot/dts/sbc8349.dts b/arch/powerpc/boot/dts/sbc8349.dts index d93e5beab731..b83036a8d0e5 100644 --- a/arch/powerpc/boot/dts/sbc8349.dts +++ b/arch/powerpc/boot/dts/sbc8349.dts @@ -265,6 +265,46 @@ }; }; + localbus@e0005000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc8349-localbus", "simple-bus"; + reg = <0xe0005000 0x1000>; + interrupts = <77 0x8>; + interrupt-parent = <&ipic>; + ranges = <0x0 0x0 0xff800000 0x00800000 /* 8MB Flash */ + 0x1 0x0 0xf8000000 0x00002000 /* 8KB EEPROM */ + 0x2 0x0 0x10000000 0x04000000 /* 64MB SDRAM */ + 0x3 0x0 0x10000000 0x04000000>; /* 64MB SDRAM */ + + flash@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "intel,28F640J3A", "cfi-flash"; + reg = <0x0 0x0 0x800000>; + bank-width = <2>; + device-width = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x00040000>; + read-only; + }; + + partition@40000 { + label = "user"; + reg = <0x00040000 0x006c0000>; + }; + + partition@700000 { + label = "legacy u-boot"; + reg = <0x00700000 0x00100000>; + read-only; + }; + + }; + }; + pci0: pci@e0008500 { interrupt-map-mask = <0xf800 0x0 0x0 0x7>; interrupt-map = < -- cgit v1.2.3 From 58dfc497b9357ec00c879b775c02f4eab19bcecb Mon Sep 17 00:00:00 2001 From: Liang Li Date: Wed, 12 Aug 2009 09:34:30 -0400 Subject: powerpc/83xx: Fix incorrect PCI interrupt map in SBC834x DTS Allows interrupts to occur on the sbc834x. Currently PCI devices get assigned an incorrect IRQ and so the interrupt count never increases. This was tested with the 82546GB based dual port E1000 PCI-X NIC which uses two distinct IRQ lines on the one card. root@localhost:/root> cat /proc/interrupts | grep eth 17: 78 IPIC Level eth1 48: 27121 IPIC Level eth0 Signed-off-by: Liang Li Signed-off-by: Yang Shi Signed-off-by: Paul Gortmaker Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/sbc8349.dts | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/powerpc/boot/dts/sbc8349.dts b/arch/powerpc/boot/dts/sbc8349.dts index b83036a8d0e5..0dc90f9bd814 100644 --- a/arch/powerpc/boot/dts/sbc8349.dts +++ b/arch/powerpc/boot/dts/sbc8349.dts @@ -310,10 +310,10 @@ interrupt-map = < /* IDSEL 0x11 */ - 0x8800 0x0 0x0 0x1 &ipic 20 0x8 - 0x8800 0x0 0x0 0x2 &ipic 21 0x8 - 0x8800 0x0 0x0 0x3 &ipic 22 0x8 - 0x8800 0x0 0x0 0x4 &ipic 23 0x8>; + 0x8800 0x0 0x0 0x1 &ipic 48 0x8 + 0x8800 0x0 0x0 0x2 &ipic 17 0x8 + 0x8800 0x0 0x0 0x3 &ipic 18 0x8 + 0x8800 0x0 0x0 0x4 &ipic 19 0x8>; interrupt-parent = <&ipic>; interrupts = <0x42 0x8>; -- cgit v1.2.3 From 944ac03804c4c9c0879347098ea458fd57f38687 Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Wed, 12 Aug 2009 09:34:31 -0400 Subject: powerpc/83xx: sbc8349 - update defconfig, enable MTD, USB storage With flash partition entries in the DTS file, MTD might as well be enabled in the defconfig. In a similar vein, enable USB and enough related options (SCSI/ext2/ext3) so that a user can read and write to a generic USB flash drive as well. Also, this board only has the two default SOC UARTs, so adjust the UART config accordingly. Signed-off-by: Paul Gortmaker Signed-off-by: Kumar Gala --- arch/powerpc/configs/83xx/sbc834x_defconfig | 320 ++++++++++++++++++++++++++-- 1 file changed, 308 insertions(+), 12 deletions(-) diff --git a/arch/powerpc/configs/83xx/sbc834x_defconfig b/arch/powerpc/configs/83xx/sbc834x_defconfig index a592b5efdc4d..3a68f861b1bd 100644 --- a/arch/powerpc/configs/83xx/sbc834x_defconfig +++ b/arch/powerpc/configs/83xx/sbc834x_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.31-rc4 -# Wed Jul 29 23:32:13 2009 +# Linux kernel version: 2.6.31-rc5 +# Tue Aug 11 19:57:51 2009 # # CONFIG_PPC64 is not set @@ -420,7 +420,90 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set -# CONFIG_MTD is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_CONCAT=y +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_TESTS is not set +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_OF_PARTS=y +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +CONFIG_MTD_CFI_INTELEXT=y +# CONFIG_MTD_CFI_AMDSTD is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_PHYSMAP_OF=y +# CONFIG_MTD_INTEL_VR_NOR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# LPDDR flash memory drivers +# +# CONFIG_MTD_LPDDR is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y CONFIG_OF_I2C=y CONFIG_OF_MDIO=y @@ -436,6 +519,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set +# CONFIG_BLK_DEV_UB is not set CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=32768 @@ -468,9 +552,38 @@ CONFIG_HAVE_IDE=y # SCSI device support # # CONFIG_RAID_ATTRS is not set -# CONFIG_SCSI is not set -# CONFIG_SCSI_DMA is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set # CONFIG_SCSI_NETLINK is not set +# CONFIG_SCSI_PROC_FS is not set + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +# CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_DH is not set +# CONFIG_SCSI_OSD_INITIATOR is not set # CONFIG_ATA is not set # CONFIG_MD is not set # CONFIG_FUSION is not set @@ -578,11 +691,21 @@ CONFIG_GIANFAR=y # # Enable WiMAX (Networking options) to see the WiMAX drivers # + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set +# CONFIG_NET_FC is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set @@ -633,9 +756,9 @@ CONFIG_DEVKMEM=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_PCI=y -CONFIG_SERIAL_8250_NR_UARTS=4 -CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +# CONFIG_SERIAL_8250_PCI is not set +CONFIG_SERIAL_8250_NR_UARTS=2 +CONFIG_SERIAL_8250_RUNTIME_UARTS=2 # CONFIG_SERIAL_8250_EXTENDED is not set # @@ -700,6 +823,7 @@ CONFIG_I2C_MPC=y # # CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set # # Graphics adapter I2C/DDC channel drivers @@ -814,6 +938,11 @@ CONFIG_WATCHDOG=y # # CONFIG_PCIPCWATCHDOG is not set # CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set CONFIG_SSB_POSSIBLE=y # @@ -856,12 +985,134 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set # CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +# CONFIG_USB_HID is not set # CONFIG_HID_PID is not set +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set + # # Special HID drivers # -# CONFIG_USB_SUPPORT is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +CONFIG_USB_ARCH_HAS_EHCI=y +CONFIG_USB=y +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=y +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_ROOT_HUB_TT=y +# CONFIG_USB_EHCI_TT_NEWSCHED is not set +CONFIG_USB_EHCI_FSL=y +CONFIG_USB_EHCI_HCD_PPC_OF=y +# CONFIG_USB_OXU210HP_HCD is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_OHCI_HCD is not set +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_WHCI_HCD is not set +# CONFIG_USB_HWA_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set + +# +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may +# + +# +# also be needed; see USB_STORAGE Help for more info +# +CONFIG_USB_STORAGE=y +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +# CONFIG_USB_SERIAL is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_SEVSEG is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_SISUSBVGA is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set +# CONFIG_USB_GADGET is not set + +# +# OTG and related infrastructure +# +# CONFIG_NOP_USB_XCEIV is not set # CONFIG_UWB is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -882,9 +1133,14 @@ CONFIG_HID=y # # File systems # -# CONFIG_EXT2_FS is not set -# CONFIG_EXT3_FS is not set +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set +# CONFIG_EXT3_FS_XATTR is not set # CONFIG_EXT4_FS is not set +CONFIG_JBD=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set @@ -940,6 +1196,7 @@ CONFIG_MISC_FILESYSTEMS=y # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set +# CONFIG_JFFS2_FS is not set # CONFIG_CRAMFS is not set # CONFIG_SQUASHFS is not set # CONFIG_VXFS_FS is not set @@ -977,7 +1234,46 @@ CONFIG_RPCSEC_GSS_KRB5=y # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y -# CONFIG_NLS is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set # CONFIG_DLM is not set # CONFIG_BINARY_PRINTF is not set -- cgit v1.2.3 From 7792da8567a70be3280c8eef916334e6923815e3 Mon Sep 17 00:00:00 2001 From: Liang Li Date: Fri, 14 Aug 2009 10:36:14 -0400 Subject: powerpc/85xx: sbc8560 - Fix warm reboot with board specific reset function The existing fsl_rstcr_restart function is not applicable to the mpc8560. The Global Utilities Block on this earlier CPU doesn't have the control/reset register at 0xe00b0. This implements a board specific reset function that uses the RCR(Reset Control Register) of the sbc8560's EPLD to do a reset. Signed-off-by: Liang Li Signed-off-by: Paul Gortmaker Signed-off-by: Kumar Gala --- arch/powerpc/platforms/85xx/sbc8560.c | 39 ++++++++++++++++++++++++++++++++++- 1 file changed, 38 insertions(+), 1 deletion(-) diff --git a/arch/powerpc/platforms/85xx/sbc8560.c b/arch/powerpc/platforms/85xx/sbc8560.c index cc27807a8b64..a5ad1c7794bf 100644 --- a/arch/powerpc/platforms/85xx/sbc8560.c +++ b/arch/powerpc/platforms/85xx/sbc8560.c @@ -267,6 +267,43 @@ arch_initcall(sbc8560_rtc_init); #endif /* M48T59 */ +static __u8 __iomem *brstcr; + +static int __init sbc8560_bdrstcr_init(void) +{ + struct device_node *np; + struct resource res; + + np = of_find_compatible_node(NULL, NULL, "wrs,sbc8560-brstcr"); + if (np == NULL) { + printk(KERN_WARNING "sbc8560: No board specific RSTCR in DTB.\n"); + return -ENODEV; + } + + of_address_to_resource(np, 0, &res); + + printk(KERN_INFO "sbc8560: Found BRSTCR at i/o 0x%x\n", res.start); + + brstcr = ioremap(res.start, res.end - res.start); + if(!brstcr) + printk(KERN_WARNING "sbc8560: ioremap of brstcr failed.\n"); + + of_node_put(np); + + return 0; +} + +arch_initcall(sbc8560_bdrstcr_init); + +void sbc8560_rstcr_restart(char * cmd) +{ + local_irq_disable(); + if(brstcr) + clrbits8(brstcr, 0x80); + + while(1); +} + define_machine(sbc8560) { .name = "SBC8560", .probe = sbc8560_probe, @@ -274,7 +311,7 @@ define_machine(sbc8560) { .init_IRQ = sbc8560_pic_init, .show_cpuinfo = sbc8560_show_cpuinfo, .get_irq = mpic_get_irq, - .restart = fsl_rstcr_restart, + .restart = sbc8560_rstcr_restart, .calibrate_decr = generic_calibrate_decr, .progress = udbg_progress, }; -- cgit v1.2.3 From 46c4c229ecf470202a1f4fd2402283cb038864bf Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Fri, 14 Aug 2009 12:13:53 -0400 Subject: powerpc/85xx: issue fsl_soc reboot warning only when applicable Some CPU, like the MPC8560 don't have a RSTCR in the Global Utilities Block. These boards will implement their own reboot call, and not use this code, so we should only warn about the absence of the GUTS RSTCR when the default reboot code is used. Signed-off-by: Paul Gortmaker Signed-off-by: Kumar Gala --- arch/powerpc/sysdev/fsl_soc.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c index 95dbc643c4fc..adca4affcf1f 100644 --- a/arch/powerpc/sysdev/fsl_soc.c +++ b/arch/powerpc/sysdev/fsl_soc.c @@ -37,6 +37,7 @@ #include #include #include +#include #include #include #include @@ -383,8 +384,9 @@ static int __init setup_rstcr(void) if (!rstcr) printk (KERN_EMERG "Error: reset control register " "not mapped!\n"); - } else - printk (KERN_INFO "rstcr compatible register does not exist!\n"); + } else if (ppc_md.restart == fsl_rstcr_restart) + printk(KERN_ERR "No RSTCR register, warm reboot won't work\n"); + if (np) of_node_put(np); return 0; -- cgit v1.2.3 From c9c419773d2a84af8ff2f91c859d3d16592c947b Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Fri, 14 Aug 2009 12:13:54 -0400 Subject: powerpc/85xx: sbc8560 - remove "has-rstcr" from global utilities block The earlier mpc8560 CPUs don't have the RSTCR at 0xe00b0 in the GUTS. The generic reboot code uses this tag to determine if it should be using the RSTCR for reboot, so remove it from the board definition. Signed-off-by: Paul Gortmaker Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/sbc8560.dts | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/powerpc/boot/dts/sbc8560.dts b/arch/powerpc/boot/dts/sbc8560.dts index 239d57a55cf4..9e13ed8a1193 100644 --- a/arch/powerpc/boot/dts/sbc8560.dts +++ b/arch/powerpc/boot/dts/sbc8560.dts @@ -303,7 +303,6 @@ global-utilities@e0000 { compatible = "fsl,mpc8560-guts"; reg = <0xe0000 0x1000>; - fsl,has-rstcr; }; }; -- cgit v1.2.3 From ec80fb2d89a0a93db46bdc968b6a849be5340531 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 19 Aug 2009 03:38:18 +0400 Subject: powerpc/85xx: Add eSDHC support for MPC8536DS boards This patch simply adds sdhci node to the device tree. We specify clock-frequency manually, so that eSDHC will work without upgrading U-Boot. Though, that'll only work for default setup (1500 MHz) on new board revisions. For non-default setups, it's recommended to upgrade U-Boot, since it will fixup clock-frequency automatically. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8536ds.dts | 8 ++++++++ arch/powerpc/boot/dts/mpc8536ds_36b.dts | 8 ++++++++ 2 files changed, 16 insertions(+) diff --git a/arch/powerpc/boot/dts/mpc8536ds.dts b/arch/powerpc/boot/dts/mpc8536ds.dts index 22caf69e6efd..815cebb2e3e5 100644 --- a/arch/powerpc/boot/dts/mpc8536ds.dts +++ b/arch/powerpc/boot/dts/mpc8536ds.dts @@ -250,6 +250,14 @@ phy_type = "ulpi"; }; + sdhci@2e000 { + compatible = "fsl,mpc8536-esdhc", "fsl,esdhc"; + reg = <0x2e000 0x1000>; + interrupts = <72 0x2>; + interrupt-parent = <&mpic>; + clock-frequency = <250000000>; + }; + serial0: serial@4500 { cell-index = <0>; device_type = "serial"; diff --git a/arch/powerpc/boot/dts/mpc8536ds_36b.dts b/arch/powerpc/boot/dts/mpc8536ds_36b.dts index 113ed8b7c898..d95b26021e62 100644 --- a/arch/powerpc/boot/dts/mpc8536ds_36b.dts +++ b/arch/powerpc/boot/dts/mpc8536ds_36b.dts @@ -250,6 +250,14 @@ phy_type = "ulpi"; }; + sdhci@2e000 { + compatible = "fsl,mpc8536-esdhc", "fsl,esdhc"; + reg = <0x2e000 0x1000>; + interrupts = <72 0x2>; + interrupt-parent = <&mpic>; + clock-frequency = <250000000>; + }; + serial0: serial@4500 { cell-index = <0>; device_type = "serial"; -- cgit v1.2.3 From a70e88bc78d220a506394058d48cedd1c491a256 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 19 Aug 2009 03:28:10 +0400 Subject: powerpc/82xx: Fix BCSR bits for MPC8272ADS boards mpc8272_ads.c is using BCSR bits definitions from pq2ads.h, but according to User's Guide the bits are wrong for MPC8272ADS boards (I guess definitions from pq2ads should only be used for PQ2FADS boards). So, let's introduce our own definitions for MPC8272ADS, and don't include pq2ads.h. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/platforms/82xx/mpc8272_ads.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/arch/powerpc/platforms/82xx/mpc8272_ads.c b/arch/powerpc/platforms/82xx/mpc8272_ads.c index 8054c685d323..67e2184f4243 100644 --- a/arch/powerpc/platforms/82xx/mpc8272_ads.c +++ b/arch/powerpc/platforms/82xx/mpc8272_ads.c @@ -29,7 +29,6 @@ #include #include -#include "pq2ads.h" #include "pq2.h" static void __init mpc8272_ads_pic_init(void) @@ -144,6 +143,13 @@ static void __init mpc8272_ads_setup_arch(void) return; } +#define BCSR1_FETHIEN 0x08000000 +#define BCSR1_FETH_RST 0x04000000 +#define BCSR1_RS232_EN1 0x02000000 +#define BCSR1_RS232_EN2 0x01000000 +#define BCSR3_FETHIEN2 0x10000000 +#define BCSR3_FETH2_RST 0x08000000 + clrbits32(&bcsr[1], BCSR1_RS232_EN1 | BCSR1_RS232_EN2 | BCSR1_FETHIEN); setbits32(&bcsr[1], BCSR1_FETH_RST); -- cgit v1.2.3 From 818fcac554397a04987d49e2bd2dfc2d394b265c Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 19 Aug 2009 03:28:17 +0400 Subject: powerpc/82xx: Add CPM USB Gadget support for MPC8272ADS boards - Add usb node; - Configure pins and clocks; - Enable USB function in BCSR. The support was successfully tested using serial and ethernet gadget drivers. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8272ads.dts | 8 ++++++++ arch/powerpc/platforms/82xx/mpc8272_ads.c | 14 ++++++++++++++ 2 files changed, 22 insertions(+) diff --git a/arch/powerpc/boot/dts/mpc8272ads.dts b/arch/powerpc/boot/dts/mpc8272ads.dts index 60f332778e41..e802ebd88cb1 100644 --- a/arch/powerpc/boot/dts/mpc8272ads.dts +++ b/arch/powerpc/boot/dts/mpc8272ads.dts @@ -173,6 +173,14 @@ fsl,cpm-command = <0xce00000>; }; + usb@11b60 { + compatible = "fsl,mpc8272-cpm-usb"; + reg = <0x11b60 0x40 0x8b00 0x100>; + interrupts = <11 8>; + interrupt-parent = <&PIC>; + mode = "peripheral"; + }; + mdio@10d40 { device_type = "mdio"; compatible = "fsl,mpc8272ads-mdio-bitbang", diff --git a/arch/powerpc/platforms/82xx/mpc8272_ads.c b/arch/powerpc/platforms/82xx/mpc8272_ads.c index 67e2184f4243..30394b409b3f 100644 --- a/arch/powerpc/platforms/82xx/mpc8272_ads.c +++ b/arch/powerpc/platforms/82xx/mpc8272_ads.c @@ -99,6 +99,15 @@ static struct cpm_pin mpc8272_ads_pins[] = { /* I2C */ {3, 14, CPM_PIN_INPUT | CPM_PIN_SECONDARY | CPM_PIN_OPENDRAIN}, {3, 15, CPM_PIN_INPUT | CPM_PIN_SECONDARY | CPM_PIN_OPENDRAIN}, + + /* USB */ + {2, 10, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, + {2, 11, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, + {2, 20, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY}, + {2, 24, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, + {3, 23, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY}, + {3, 24, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY}, + {3, 25, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, }; static void __init init_ioports(void) @@ -112,6 +121,8 @@ static void __init init_ioports(void) cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_RX); cpm2_clk_setup(CPM_CLK_SCC1, CPM_BRG1, CPM_CLK_TX); + cpm2_clk_setup(CPM_CLK_SCC3, CPM_CLK8, CPM_CLK_RX); + cpm2_clk_setup(CPM_CLK_SCC3, CPM_CLK8, CPM_CLK_TX); cpm2_clk_setup(CPM_CLK_SCC4, CPM_BRG4, CPM_CLK_RX); cpm2_clk_setup(CPM_CLK_SCC4, CPM_BRG4, CPM_CLK_TX); cpm2_clk_setup(CPM_CLK_FCC1, CPM_CLK11, CPM_CLK_RX); @@ -147,6 +158,7 @@ static void __init mpc8272_ads_setup_arch(void) #define BCSR1_FETH_RST 0x04000000 #define BCSR1_RS232_EN1 0x02000000 #define BCSR1_RS232_EN2 0x01000000 +#define BCSR3_USB_nEN 0x80000000 #define BCSR3_FETHIEN2 0x10000000 #define BCSR3_FETH2_RST 0x08000000 @@ -156,6 +168,8 @@ static void __init mpc8272_ads_setup_arch(void) clrbits32(&bcsr[3], BCSR3_FETHIEN2); setbits32(&bcsr[3], BCSR3_FETH2_RST); + clrbits32(&bcsr[3], BCSR3_USB_nEN); + iounmap(bcsr); init_ioports(); -- cgit v1.2.3 From 9b9d401b8d11796f4c4bcbcabecfec9f5d85ea25 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 19 Aug 2009 03:28:21 +0400 Subject: powerpc/85xx: Add QE USB support for MPC8569E-MDS boards - Add gpio-controller node for BCSR17, it is used to control USB speed and VBUS; - Add timer node for QE GTM, needed for USB host; - Add usb node itself; - Add some probing code for BCSR GPIOs. NOTE: QE USB doesn't work on prototype boards, but should work on pilot boards if specs and schematics are correct, though we don't have the pilot boards to actually test it. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8569mds.dts | 45 +++++++++++++++++++++++++++++++ arch/powerpc/platforms/85xx/mpc85xx_mds.c | 4 +++ 2 files changed, 49 insertions(+) diff --git a/arch/powerpc/boot/dts/mpc8569mds.dts b/arch/powerpc/boot/dts/mpc8569mds.dts index 9e4ce99e1613..06332d61830a 100644 --- a/arch/powerpc/boot/dts/mpc8569mds.dts +++ b/arch/powerpc/boot/dts/mpc8569mds.dts @@ -99,8 +99,18 @@ }; bcsr@1,0 { + #address-cells = <1>; + #size-cells = <1>; compatible = "fsl,mpc8569mds-bcsr"; reg = <1 0 0x8000>; + ranges = <0 1 0 0x8000>; + + bcsr17: gpio-controller@11 { + #gpio-cells = <2>; + compatible = "fsl,mpc8569mds-bcsr-gpio"; + reg = <0x11 0x1>; + gpio-controller; + }; }; nand@3,0 { @@ -315,6 +325,14 @@ gpio-controller; }; + qe_pio_f: gpio-controller@a0 { + #gpio-cells = <2>; + compatible = "fsl,mpc8569-qe-pario-bank", + "fsl,mpc8323-qe-pario-bank"; + reg = <0xa0 0x18>; + gpio-controller; + }; + pio1: ucc_pin@01 { pio-map = < /* port pin dir open_drain assignment has_irq */ @@ -419,6 +437,16 @@ interrupt-parent = <&mpic>; }; + timer@440 { + compatible = "fsl,mpc8569-qe-gtm", + "fsl,qe-gtm", "fsl,gtm"; + reg = <0x440 0x40>; + interrupts = <12 13 14 15>; + interrupt-parent = <&qeic>; + /* Filled in by U-Boot */ + clock-frequency = <0>; + }; + spi@4c0 { #address-cells = <1>; #size-cells = <0>; @@ -446,6 +474,23 @@ mode = "cpu"; }; + usb@6c0 { + compatible = "fsl,mpc8569-qe-usb", + "fsl,mpc8323-qe-usb"; + reg = <0x6c0 0x40 0x8b00 0x100>; + interrupts = <11>; + interrupt-parent = <&qeic>; + fsl,fullspeed-clock = "clk5"; + fsl,lowspeed-clock = "brg10"; + gpios = <&qe_pio_f 3 0 /* USBOE */ + &qe_pio_f 4 0 /* USBTP */ + &qe_pio_f 5 0 /* USBTN */ + &qe_pio_f 6 0 /* USBRP */ + &qe_pio_f 8 0 /* USBRN */ + &bcsr17 6 0 /* SPEED */ + &bcsr17 5 1>; /* POWER */ + }; + enet0: ucc@2000 { device_type = "network"; compatible = "ucc_geth"; diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c index bfb32834ab0c..20a61d0af33b 100644 --- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c +++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c @@ -47,6 +47,7 @@ #include #include #include +#include #include #include #include @@ -304,6 +305,9 @@ static struct of_device_id mpc85xx_ids[] = { static int __init mpc85xx_publish_devices(void) { + if (machine_is(mpc8569_mds)) + simple_gpiochip_init("fsl,mpc8569mds-bcsr-gpio"); + /* Publish the QE devices */ of_platform_bus_probe(NULL, mpc85xx_ids, NULL); -- cgit v1.2.3 From 1dcd8ffc81e80a170625883f63f6a5db3cd0428d Mon Sep 17 00:00:00 2001 From: Michael Barkowski Date: Tue, 18 Aug 2009 17:20:44 -0400 Subject: powerpc/qe_lib: Set gpio data before changing the direction to output This avoids having a short glitch if the desired initial value is not the same as what was previously in the data register. Signed-off-by: Michael Barkowski Acked-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/sysdev/qe_lib/gpio.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/powerpc/sysdev/qe_lib/gpio.c b/arch/powerpc/sysdev/qe_lib/gpio.c index 3485288dce31..8e7a7767dd5c 100644 --- a/arch/powerpc/sysdev/qe_lib/gpio.c +++ b/arch/powerpc/sysdev/qe_lib/gpio.c @@ -105,14 +105,14 @@ static int qe_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val) struct qe_gpio_chip *qe_gc = to_qe_gpio_chip(mm_gc); unsigned long flags; + qe_gpio_set(gc, gpio, val); + spin_lock_irqsave(&qe_gc->lock, flags); __par_io_config_pin(mm_gc->regs, gpio, QE_PIO_DIR_OUT, 0, 0, 0); spin_unlock_irqrestore(&qe_gc->lock, flags); - qe_gpio_set(gc, gpio, val); - return 0; } -- cgit v1.2.3