From 7e36e2f5355ab87f8946041d044b34cda01e2077 Mon Sep 17 00:00:00 2001 From: Rod Whitby Date: Tue, 1 Apr 2008 10:53:23 +0100 Subject: [ARM] 4874/2: ixp4xx: Add support for the Freecom FSG-3 board The Freecom-FSG3 is a small network-attached-storage device with the following feature set: * Intel IXP422 * 4MB Flash (ixp4xx flash driver) * 64MB RAM * 4 USB 2.0 host ports (ehci and ohci drivers) * 1 WAN (eth1) and 3 LAN (eth0) ethernet ports * Supported by the open source ixp4xx ethernet driver * Via VT6421 disk controller (libata and sata-via drivers) * Internal hard disk (PATA supported, SATA not yet supported) * External SATA port (not yet supported) * ISL1208 RTC chip * Winbond 83782 temp sensor and fan controller * MiniPCI slot The ixp4xx_defconfig is also updated to support this device (the leds-fsg driver is to be submitted separately via the leds tree after this initial support is merged, as it depends on header gpio defines). Signed-off-by: Rod Whitby Signed-off-by: Russell King --- arch/arm/configs/ixp4xx_defconfig | 9 +- arch/arm/mach-ixp4xx/Kconfig | 9 ++ arch/arm/mach-ixp4xx/Makefile | 2 + arch/arm/mach-ixp4xx/fsg-pci.c | 71 +++++++++ arch/arm/mach-ixp4xx/fsg-setup.c | 276 +++++++++++++++++++++++++++++++++ include/asm-arm/arch-ixp4xx/fsg.h | 50 ++++++ include/asm-arm/arch-ixp4xx/hardware.h | 1 + include/asm-arm/arch-ixp4xx/irqs.h | 7 + 8 files changed, 421 insertions(+), 4 deletions(-) create mode 100644 arch/arm/mach-ixp4xx/fsg-pci.c create mode 100644 arch/arm/mach-ixp4xx/fsg-setup.c create mode 100644 include/asm-arm/arch-ixp4xx/fsg.h diff --git a/arch/arm/configs/ixp4xx_defconfig b/arch/arm/configs/ixp4xx_defconfig index efa0485d2f7e..fc14932e3abd 100644 --- a/arch/arm/configs/ixp4xx_defconfig +++ b/arch/arm/configs/ixp4xx_defconfig @@ -165,6 +165,7 @@ CONFIG_ARCH_PRPMC1100=y CONFIG_MACH_NAS100D=y CONFIG_MACH_DSMG600=y CONFIG_ARCH_IXDP4XX=y +CONFIG_MACH_FSG=y CONFIG_CPU_IXP46X=y CONFIG_CPU_IXP43X=y CONFIG_MACH_GTWX5715=y @@ -770,7 +771,7 @@ CONFIG_ATA=y # CONFIG_SATA_SIL24 is not set # CONFIG_SATA_SIS is not set # CONFIG_SATA_ULI is not set -# CONFIG_SATA_VIA is not set +CONFIG_SATA_VIA=y # CONFIG_SATA_VITESSE is not set # CONFIG_SATA_INIC162X is not set # CONFIG_PATA_ALI is not set @@ -1143,7 +1144,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set -# CONFIG_SENSORS_W83781D is not set +CONFIG_SENSORS_W83781D=y # CONFIG_SENSORS_W83791D is not set # CONFIG_SENSORS_W83792D is not set # CONFIG_SENSORS_W83793 is not set @@ -1334,8 +1335,8 @@ CONFIG_LEDS_CLASS=y # # LED drivers # -# CONFIG_LEDS_IXP4XX is not set CONFIG_LEDS_GPIO=y +CONFIG_LEDS_FSG=y # # LED Triggers @@ -1367,7 +1368,7 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set # CONFIG_RTC_DRV_RS5C372 is not set -# CONFIG_RTC_DRV_ISL1208 is not set +CONFIG_RTC_DRV_ISL1208=y CONFIG_RTC_DRV_X1205=y CONFIG_RTC_DRV_PCF8563=y # CONFIG_RTC_DRV_PCF8583 is not set diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig index e774447c0592..db8b5fe06c0d 100644 --- a/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig @@ -125,6 +125,15 @@ config ARCH_IXDP4XX depends on ARCH_IXDP425 || MACH_IXDP465 || MACH_KIXRP435 default y +config MACH_FSG + bool + prompt "Freecom FSG-3" + select PCI + help + Say 'Y' here if you want your kernel to support Freecom's + FSG-3 device. For more information on this platform, + see http://www.nslu2-linux.org/wiki/FSG3/HomePage + # # Certain registers and IRQs are only enabled if supporting IXP465 CPUs # diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile index c1956882c48b..2e6bbf927a74 100644 --- a/arch/arm/mach-ixp4xx/Makefile +++ b/arch/arm/mach-ixp4xx/Makefile @@ -15,6 +15,7 @@ obj-pci-$(CONFIG_MACH_NAS100D) += nas100d-pci.o obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o +obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o obj-y += common.o @@ -28,6 +29,7 @@ obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o +obj-$(CONFIG_MACH_FSG) += fsg-setup.o obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o diff --git a/arch/arm/mach-ixp4xx/fsg-pci.c b/arch/arm/mach-ixp4xx/fsg-pci.c new file mode 100644 index 000000000000..f19f3f6feda1 --- /dev/null +++ b/arch/arm/mach-ixp4xx/fsg-pci.c @@ -0,0 +1,71 @@ +/* + * arch/arch/mach-ixp4xx/fsg-pci.c + * + * FSG board-level PCI initialization + * + * Author: Rod Whitby + * Maintainer: http://www.nslu2-linux.org/ + * + * based on ixdp425-pci.c: + * Copyright (C) 2002 Intel Corporation. + * Copyright (C) 2003-2004 MontaVista Software, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include +#include +#include + +#include +#include + +void __init fsg_pci_preinit(void) +{ + set_irq_type(IRQ_FSG_PCI_INTA, IRQT_LOW); + set_irq_type(IRQ_FSG_PCI_INTB, IRQT_LOW); + set_irq_type(IRQ_FSG_PCI_INTC, IRQT_LOW); + + ixp4xx_pci_preinit(); +} + +static int __init fsg_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + static int pci_irq_table[FSG_PCI_IRQ_LINES] = { + IRQ_FSG_PCI_INTC, + IRQ_FSG_PCI_INTB, + IRQ_FSG_PCI_INTA, + }; + + int irq = -1; + slot = slot - 11; + + if (slot >= 1 && slot <= FSG_PCI_MAX_DEV && + pin >= 1 && pin <= FSG_PCI_IRQ_LINES) + irq = pci_irq_table[(slot - 1)]; + printk(KERN_INFO "%s: Mapped slot %d pin %d to IRQ %d\n", + __func__, slot, pin, irq); + + return irq; +} + +struct hw_pci fsg_pci __initdata = { + .nr_controllers = 1, + .preinit = fsg_pci_preinit, + .swizzle = pci_std_swizzle, + .setup = ixp4xx_setup, + .scan = ixp4xx_scan_bus, + .map_irq = fsg_map_irq, +}; + +int __init fsg_pci_init(void) +{ + if (machine_is_fsg()) + pci_common_init(&fsg_pci); + return 0; +} + +subsys_initcall(fsg_pci_init); diff --git a/arch/arm/mach-ixp4xx/fsg-setup.c b/arch/arm/mach-ixp4xx/fsg-setup.c new file mode 100644 index 000000000000..0db3a909ae61 --- /dev/null +++ b/arch/arm/mach-ixp4xx/fsg-setup.c @@ -0,0 +1,276 @@ +/* + * arch/arm/mach-ixp4xx/fsg-setup.c + * + * FSG board-setup + * + * Copyright (C) 2008 Rod Whitby + * + * based on ixdp425-setup.c: + * Copyright (C) 2003-2004 MontaVista Software, Inc. + * based on nslu2-power.c + * Copyright (C) 2005 Tower Technologies + * + * Author: Rod Whitby + * Maintainers: http://www.nslu2-linux.org/ + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +static struct flash_platform_data fsg_flash_data = { + .map_name = "cfi_probe", + .width = 2, +}; + +static struct resource fsg_flash_resource = { + .flags = IORESOURCE_MEM, +}; + +static struct platform_device fsg_flash = { + .name = "IXP4XX-Flash", + .id = 0, + .dev = { + .platform_data = &fsg_flash_data, + }, + .num_resources = 1, + .resource = &fsg_flash_resource, +}; + +static struct i2c_gpio_platform_data fsg_i2c_gpio_data = { + .sda_pin = FSG_SDA_PIN, + .scl_pin = FSG_SCL_PIN, +}; + +static struct platform_device fsg_i2c_gpio = { + .name = "i2c-gpio", + .id = 0, + .dev = { + .platform_data = &fsg_i2c_gpio_data, + }, +}; + +static struct i2c_board_info __initdata fsg_i2c_board_info [] = { + { + I2C_BOARD_INFO("rtc-isl1208", 0x6f), + }, +}; + +static struct resource fsg_uart_resources[] = { + { + .start = IXP4XX_UART1_BASE_PHYS, + .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM, + }, + { + .start = IXP4XX_UART2_BASE_PHYS, + .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM, + } +}; + +static struct plat_serial8250_port fsg_uart_data[] = { + { + .mapbase = IXP4XX_UART1_BASE_PHYS, + .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, + .irq = IRQ_IXP4XX_UART1, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { + .mapbase = IXP4XX_UART2_BASE_PHYS, + .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, + .irq = IRQ_IXP4XX_UART2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { } +}; + +static struct platform_device fsg_uart = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = fsg_uart_data, + }, + .num_resources = ARRAY_SIZE(fsg_uart_resources), + .resource = fsg_uart_resources, +}; + +static struct platform_device fsg_leds = { + .name = "fsg-led", + .id = -1, +}; + +/* Built-in 10/100 Ethernet MAC interfaces */ +static struct eth_plat_info fsg_plat_eth[] = { + { + .phy = 5, + .rxq = 3, + .txreadyq = 20, + }, { + .phy = 4, + .rxq = 4, + .txreadyq = 21, + } +}; + +static struct platform_device fsg_eth[] = { + { + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEB, + .dev = { + .platform_data = fsg_plat_eth, + }, + }, { + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEC, + .dev = { + .platform_data = fsg_plat_eth + 1, + }, + } +}; + +static struct platform_device *fsg_devices[] __initdata = { + &fsg_i2c_gpio, + &fsg_flash, + &fsg_leds, + &fsg_eth[0], + &fsg_eth[1], +}; + +static irqreturn_t fsg_power_handler(int irq, void *dev_id) +{ + /* Signal init to do the ctrlaltdel action, this will bypass init if + * it hasn't started and do a kernel_restart. + */ + ctrl_alt_del(); + + return IRQ_HANDLED; +} + +static irqreturn_t fsg_reset_handler(int irq, void *dev_id) +{ + /* This is the paper-clip reset which does an emergency reboot. */ + printk(KERN_INFO "Restarting system.\n"); + machine_restart(NULL); + + /* This should never be reached. */ + return IRQ_HANDLED; +} + +static void __init fsg_init(void) +{ + DECLARE_MAC_BUF(mac_buf); + uint8_t __iomem *f; + int i; + + ixp4xx_sys_init(); + + fsg_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); + fsg_flash_resource.end = + IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; + + *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; + *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; + + /* Configure CS2 for operation, 8bit and writable */ + *IXP4XX_EXP_CS2 = 0xbfff0002; + + i2c_register_board_info(0, fsg_i2c_board_info, + ARRAY_SIZE(fsg_i2c_board_info)); + + /* This is only useful on a modified machine, but it is valuable + * to have it first in order to see debug messages, and so that + * it does *not* get removed if platform_add_devices fails! + */ + (void)platform_device_register(&fsg_uart); + + platform_add_devices(fsg_devices, ARRAY_SIZE(fsg_devices)); + + if (request_irq(gpio_to_irq(FSG_RB_GPIO), &fsg_reset_handler, + IRQF_DISABLED | IRQF_TRIGGER_LOW, + "FSG reset button", NULL) < 0) { + + printk(KERN_DEBUG "Reset Button IRQ %d not available\n", + gpio_to_irq(FSG_RB_GPIO)); + } + + if (request_irq(gpio_to_irq(FSG_SB_GPIO), &fsg_power_handler, + IRQF_DISABLED | IRQF_TRIGGER_LOW, + "FSG power button", NULL) < 0) { + + printk(KERN_DEBUG "Power Button IRQ %d not available\n", + gpio_to_irq(FSG_SB_GPIO)); + } + + /* + * Map in a portion of the flash and read the MAC addresses. + * Since it is stored in BE in the flash itself, we need to + * byteswap it if we're in LE mode. + */ + f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x400000); + if (f) { +#ifdef __ARMEB__ + for (i = 0; i < 6; i++) { + fsg_plat_eth[0].hwaddr[i] = readb(f + 0x3C0422 + i); + fsg_plat_eth[1].hwaddr[i] = readb(f + 0x3C043B + i); + } +#else + + /* + Endian-swapped reads from unaligned addresses are + required to extract the two MACs from the big-endian + Redboot config area in flash. + */ + + fsg_plat_eth[0].hwaddr[0] = readb(f + 0x3C0421); + fsg_plat_eth[0].hwaddr[1] = readb(f + 0x3C0420); + fsg_plat_eth[0].hwaddr[2] = readb(f + 0x3C0427); + fsg_plat_eth[0].hwaddr[3] = readb(f + 0x3C0426); + fsg_plat_eth[0].hwaddr[4] = readb(f + 0x3C0425); + fsg_plat_eth[0].hwaddr[5] = readb(f + 0x3C0424); + + fsg_plat_eth[1].hwaddr[0] = readb(f + 0x3C0439); + fsg_plat_eth[1].hwaddr[1] = readb(f + 0x3C043F); + fsg_plat_eth[1].hwaddr[2] = readb(f + 0x3C043E); + fsg_plat_eth[1].hwaddr[3] = readb(f + 0x3C043D); + fsg_plat_eth[1].hwaddr[4] = readb(f + 0x3C043C); + fsg_plat_eth[1].hwaddr[5] = readb(f + 0x3C0443); +#endif + iounmap(f); + } + printk(KERN_INFO "FSG: Using MAC address %s for port 0\n", + print_mac(mac_buf, fsg_plat_eth[0].hwaddr)); + printk(KERN_INFO "FSG: Using MAC address %s for port 1\n", + print_mac(mac_buf, fsg_plat_eth[1].hwaddr)); + +} + +MACHINE_START(FSG, "Freecom FSG-3") + /* Maintainer: www.nslu2-linux.org */ + .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, + .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc, + .map_io = ixp4xx_map_io, + .init_irq = ixp4xx_init_irq, + .timer = &ixp4xx_timer, + .boot_params = 0x0100, + .init_machine = fsg_init, +MACHINE_END + diff --git a/include/asm-arm/arch-ixp4xx/fsg.h b/include/asm-arm/arch-ixp4xx/fsg.h new file mode 100644 index 000000000000..c0100cc7981c --- /dev/null +++ b/include/asm-arm/arch-ixp4xx/fsg.h @@ -0,0 +1,50 @@ +/* + * include/asm-arm/arch-ixp4xx/fsg.h + * + * Freecom FSG-3 platform specific definitions + * + * Author: Rod Whitby + * Author: Tomasz Chmielewski + * Maintainers: http://www.nslu2-linux.org + * + * Based on coyote.h by + * Copyright 2004 (c) MontaVista, Software, Inc. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_HARDWARE_H__ +#error "Do not include this directly, instead #include " +#endif + +#define FSG_SDA_PIN 12 +#define FSG_SCL_PIN 13 + +/* + * FSG PCI IRQs + */ +#define FSG_PCI_MAX_DEV 3 +#define FSG_PCI_IRQ_LINES 3 + + +/* PCI controller GPIO to IRQ pin mappings */ +#define FSG_PCI_INTA_PIN 6 +#define FSG_PCI_INTB_PIN 7 +#define FSG_PCI_INTC_PIN 5 + +/* Buttons */ + +#define FSG_SB_GPIO 4 /* sync button */ +#define FSG_RB_GPIO 9 /* reset button */ +#define FSG_UB_GPIO 10 /* usb button */ + +/* LEDs */ + +#define FSG_LED_WLAN_BIT 0 +#define FSG_LED_WAN_BIT 1 +#define FSG_LED_SATA_BIT 2 +#define FSG_LED_USB_BIT 4 +#define FSG_LED_RING_BIT 5 +#define FSG_LED_SYNC_BIT 7 diff --git a/include/asm-arm/arch-ixp4xx/hardware.h b/include/asm-arm/arch-ixp4xx/hardware.h index 73e8dc36f6a4..fa723a627854 100644 --- a/include/asm-arm/arch-ixp4xx/hardware.h +++ b/include/asm-arm/arch-ixp4xx/hardware.h @@ -45,5 +45,6 @@ #include "nslu2.h" #include "nas100d.h" #include "dsmg600.h" +#include "fsg.h" #endif /* _ASM_ARCH_HARDWARE_H */ diff --git a/include/asm-arm/arch-ixp4xx/irqs.h b/include/asm-arm/arch-ixp4xx/irqs.h index 11801605047b..674af4a84147 100644 --- a/include/asm-arm/arch-ixp4xx/irqs.h +++ b/include/asm-arm/arch-ixp4xx/irqs.h @@ -128,4 +128,11 @@ #define IRQ_DSMG600_PCI_INTE IRQ_IXP4XX_GPIO7 #define IRQ_DSMG600_PCI_INTF IRQ_IXP4XX_GPIO6 +/* + * Freecom FSG-3 Board IRQs + */ +#define IRQ_FSG_PCI_INTA IRQ_IXP4XX_GPIO6 +#define IRQ_FSG_PCI_INTB IRQ_IXP4XX_GPIO7 +#define IRQ_FSG_PCI_INTC IRQ_IXP4XX_GPIO5 + #endif -- cgit v1.2.3 From e055d5bff318845f99c0fbf93245767fab8dce88 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Tue, 22 Apr 2008 01:43:27 +0100 Subject: [ARM] 5015/1: arm: remove ARCH_CO285 Trying to compile a kerel for ARCH_CO285 fails with the following error: <-- snip --> ... CC arch/arm/mach-footbridge/dc21285.o /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c: In function 'dc21285_base_address': /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: 'PCICFG0_BASE' undeclared (first use in this function) /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: (Each undeclared identifier is reported only once /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:54: error: for each function it appears in.) /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:57: error: 'PCICFG1_BASE' undeclared (first use in this function) /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c: In function 'dc21285_scan_bus': /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/arm/mach-footbridge/dc21285.c:286: error: implicit declaration of function 'pci_scan_bus' ... make[2]: *** [arch/arm/mach-footbridge/dc21285.o] Error 1 <-- snip --> This does not seem to be a recent breakage. The ARCH_CO285 support is old - kernel 2.2.0 contains first traces of it, an it seems to have been pretty complete in later 2.2 kernels. Since it seems to be completely dead code now this patch therefore removes it. Signed-off-by: Adrian Bunk Signed-off-by: Russell King --- arch/arm/Kconfig | 10 +-------- arch/arm/Makefile | 2 -- arch/arm/mach-footbridge/Makefile | 2 -- arch/arm/mach-footbridge/co285.c | 39 --------------------------------- arch/arm/mach-footbridge/common.c | 21 ------------------ arch/arm/mach-footbridge/ebsa285-leds.c | 2 +- arch/arm/mach-footbridge/time.c | 3 +-- include/asm-arm/arch-ebsa285/hardware.h | 26 ---------------------- include/asm-arm/arch-ebsa285/memory.h | 19 ---------------- include/asm-arm/arch-ebsa285/vmalloc.h | 4 ---- 10 files changed, 3 insertions(+), 125 deletions(-) delete mode 100644 arch/arm/mach-footbridge/co285.c diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 4039a133006e..ab78d5c421fd 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -232,14 +232,6 @@ config ARCH_CLPS711X help Support for Cirrus Logic 711x/721x based boards. -config ARCH_CO285 - bool "Co-EBSA285" - select FOOTBRIDGE - select FOOTBRIDGE_ADDIN - select HAVE_IDE - help - Support for Intel's EBSA285 companion chip. - config ARCH_EBSA110 bool "EBSA-110" select ISA @@ -784,7 +776,7 @@ source "mm/Kconfig" config LEDS bool "Timer and CPU usage LEDs" - depends on ARCH_CDB89712 || ARCH_CO285 || ARCH_EBSA110 || \ + depends on ARCH_CDB89712 || ARCH_EBSA110 || \ ARCH_EBSA285 || ARCH_IMX || ARCH_INTEGRATOR || \ ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \ ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \ diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 1a4649667ec8..79b8ca3400e0 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -100,8 +100,6 @@ textofs-y := 0x00008000 incdir-$(CONFIG_ARCH_CLPS7500) := cl7500 machine-$(CONFIG_FOOTBRIDGE) := footbridge incdir-$(CONFIG_FOOTBRIDGE) := ebsa285 - machine-$(CONFIG_ARCH_CO285) := footbridge - incdir-$(CONFIG_ARCH_CO285) := ebsa285 machine-$(CONFIG_ARCH_SHARK) := shark machine-$(CONFIG_ARCH_SA1100) := sa1100 ifeq ($(CONFIG_ARCH_SA1100),y) diff --git a/arch/arm/mach-footbridge/Makefile b/arch/arm/mach-footbridge/Makefile index 0694ad6b6476..32f8609e4f85 100644 --- a/arch/arm/mach-footbridge/Makefile +++ b/arch/arm/mach-footbridge/Makefile @@ -14,12 +14,10 @@ pci-$(CONFIG_ARCH_EBSA285_HOST) += ebsa285-pci.o pci-$(CONFIG_ARCH_NETWINDER) += netwinder-pci.o pci-$(CONFIG_ARCH_PERSONAL_SERVER) += personal-pci.o -leds-$(CONFIG_ARCH_CO285) += ebsa285-leds.o leds-$(CONFIG_ARCH_EBSA285) += ebsa285-leds.o leds-$(CONFIG_ARCH_NETWINDER) += netwinder-leds.o obj-$(CONFIG_ARCH_CATS) += cats-hw.o isa-timer.o -obj-$(CONFIG_ARCH_CO285) += co285.o dc21285-timer.o obj-$(CONFIG_ARCH_EBSA285) += ebsa285.o dc21285-timer.o obj-$(CONFIG_ARCH_NETWINDER) += netwinder-hw.o isa-timer.o obj-$(CONFIG_ARCH_PERSONAL_SERVER) += personal.o dc21285-timer.o diff --git a/arch/arm/mach-footbridge/co285.c b/arch/arm/mach-footbridge/co285.c deleted file mode 100644 index 4545576ad8d9..000000000000 --- a/arch/arm/mach-footbridge/co285.c +++ /dev/null @@ -1,39 +0,0 @@ -/* - * linux/arch/arm/mach-footbridge/co285.c - * - * CO285 machine fixup - */ -#include - -#include -#include - -#include - -#include "common.h" - -static void __init -fixup_coebsa285(struct machine_desc *desc, struct tag *tags, - char **cmdline, struct meminfo *mi) -{ - extern unsigned long boot_memory_end; - extern char boot_command_line[]; - - mi->nr_banks = 1; - mi->bank[0].start = PHYS_OFFSET; - mi->bank[0].size = boot_memory_end; - mi->bank[0].node = 0; - - *cmdline = boot_command_line; -} - -MACHINE_START(CO285, "co-EBSA285") - /* Maintainer: Mark van Doesburg */ - .phys_io = DC21285_ARMCSR_BASE, - .io_pg_offst = ((0x7cf00000) >> 18) & 0xfffc, - .fixup = fixup_coebsa285, - .map_io = footbridge_map_io, - .init_irq = footbridge_init_irq, - .timer = &footbridge_timer, -MACHINE_END - diff --git a/arch/arm/mach-footbridge/common.c b/arch/arm/mach-footbridge/common.c index ef29fc34ce65..b08ab507c052 100644 --- a/arch/arm/mach-footbridge/common.c +++ b/arch/arm/mach-footbridge/common.c @@ -177,25 +177,6 @@ static struct map_desc ebsa285_host_io_desc[] __initdata = { #endif }; -/* - * The CO-ebsa285 mapping. - */ -static struct map_desc co285_io_desc[] __initdata = { -#ifdef CONFIG_ARCH_CO285 - { - .virtual = PCIO_BASE, - .pfn = __phys_to_pfn(DC21285_PCI_IO), - .length = PCIO_SIZE, - .type = MT_DEVICE, - }, { - .virtual = PCIMEM_BASE, - .pfn = __phys_to_pfn(DC21285_PCI_MEM), - .length = PCIMEM_SIZE, - .type = MT_DEVICE, - }, -#endif -}; - void __init footbridge_map_io(void) { /* @@ -208,8 +189,6 @@ void __init footbridge_map_io(void) * Now, work out what we've got to map in addition on this * platform. */ - if (machine_is_co285()) - iotable_init(co285_io_desc, ARRAY_SIZE(co285_io_desc)); if (footbridge_cfn_mode()) iotable_init(ebsa285_host_io_desc, ARRAY_SIZE(ebsa285_host_io_desc)); } diff --git a/arch/arm/mach-footbridge/ebsa285-leds.c b/arch/arm/mach-footbridge/ebsa285-leds.c index a64e22226515..09c1fbc51876 100644 --- a/arch/arm/mach-footbridge/ebsa285-leds.c +++ b/arch/arm/mach-footbridge/ebsa285-leds.c @@ -128,7 +128,7 @@ static void ebsa285_leds_event(led_event_t evt) static int __init leds_init(void) { - if (machine_is_ebsa285() || machine_is_co285()) + if (machine_is_ebsa285()) leds_event = ebsa285_leds_event; leds_event(led_start); diff --git a/arch/arm/mach-footbridge/time.c b/arch/arm/mach-footbridge/time.c index 5d02e95dede3..d5cfcda385d6 100644 --- a/arch/arm/mach-footbridge/time.c +++ b/arch/arm/mach-footbridge/time.c @@ -115,8 +115,7 @@ static int set_isa_cmos_time(void) void __init isa_rtc_init(void) { - if (machine_is_co285() || - machine_is_personal_server()) + if (machine_is_personal_server()) /* * Add-in 21285s shouldn't access the RTC */ diff --git a/include/asm-arm/arch-ebsa285/hardware.h b/include/asm-arm/arch-ebsa285/hardware.h index daad8ee2d194..74610c2c63d4 100644 --- a/include/asm-arm/arch-ebsa285/hardware.h +++ b/include/asm-arm/arch-ebsa285/hardware.h @@ -14,7 +14,6 @@ #include -#ifdef CONFIG_ARCH_FOOTBRIDGE /* Virtual Physical Size * 0xff800000 0x40000000 1MB X-Bus * 0xff000000 0x7c000000 1MB PCI I/O space @@ -50,31 +49,6 @@ #define PCIMEM_SIZE 0x01000000 #define PCIMEM_BASE 0xf0000000 -#elif defined(CONFIG_ARCH_CO285) -/* - * This is the COEBSA285 cut-down mapping - */ -#define PCIMEM_SIZE 0x80000000 -#define PCIMEM_BASE 0x80000000 - -#define WFLUSH_SIZE 0x01000000 -#define WFLUSH_BASE 0x7d000000 - -#define ARMCSR_SIZE 0x00100000 -#define ARMCSR_BASE 0x7cf00000 - -#define XBUS_SIZE 0x00020000 -#define XBUS_BASE 0x7cee0000 - -#define PCIO_SIZE 0x00010000 -#define PCIO_BASE 0x7ced0000 - -#else - -#error "Undefined footbridge architecture" - -#endif - #define XBUS_LEDS ((volatile unsigned char *)(XBUS_BASE + 0x12000)) #define XBUS_LED_AMBER (1 << 0) #define XBUS_LED_GREEN (1 << 1) diff --git a/include/asm-arm/arch-ebsa285/memory.h b/include/asm-arm/arch-ebsa285/memory.h index cbd7ae64bcc9..9019a3bf5ab9 100644 --- a/include/asm-arm/arch-ebsa285/memory.h +++ b/include/asm-arm/arch-ebsa285/memory.h @@ -42,8 +42,6 @@ extern unsigned long __bus_to_virt(unsigned long); #endif -#if defined(CONFIG_ARCH_FOOTBRIDGE) - /* Task size and page offset at 3GB */ #define TASK_SIZE UL(0xbf000000) #define PAGE_OFFSET UL(0xc0000000) @@ -53,23 +51,6 @@ extern unsigned long __bus_to_virt(unsigned long); */ #define FLUSH_BASE 0xf9000000 -#elif defined(CONFIG_ARCH_CO285) - -/* Task size and page offset at 1.5GB */ -#define TASK_SIZE UL(0x5f000000) -#define PAGE_OFFSET UL(0x60000000) - -/* - * Cache flushing area. - */ -#define FLUSH_BASE 0x7e000000 - -#else - -#error "Undefined footbridge architecture" - -#endif - /* * Physical DRAM offset. */ diff --git a/include/asm-arm/arch-ebsa285/vmalloc.h b/include/asm-arm/arch-ebsa285/vmalloc.h index 02598200997d..e487d7e8c8a6 100644 --- a/include/asm-arm/arch-ebsa285/vmalloc.h +++ b/include/asm-arm/arch-ebsa285/vmalloc.h @@ -7,8 +7,4 @@ */ -#ifdef CONFIG_ARCH_FOOTBRIDGE #define VMALLOC_END (PAGE_OFFSET + 0x30000000) -#else -#define VMALLOC_END (PAGE_OFFSET + 0x20000000) -#endif -- cgit v1.2.3 From 205bee6ad804d7034773b5978c74dde495df2301 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 13:57:26 +0100 Subject: [ARM] dyntick: Remove obsolete and unused ARM dyntick support dyntick is superseded by the clocksource/clockevent infrastructure, using the NO_HZ configuration option. No one implements dyntick on ARM anymore, so it's pointless keeping it around. Remove dyntick support. Signed-off-by: Russell King --- arch/arm/Kconfig | 21 ------ arch/arm/configs/at91cap9adk_defconfig | 1 - arch/arm/configs/at91rm9200dk_defconfig | 1 - arch/arm/configs/at91rm9200ek_defconfig | 1 - arch/arm/configs/at91sam9260ek_defconfig | 1 - arch/arm/configs/at91sam9261ek_defconfig | 1 - arch/arm/configs/at91sam9263ek_defconfig | 1 - arch/arm/configs/at91sam9rlek_defconfig | 1 - arch/arm/configs/ateb9200_defconfig | 1 - arch/arm/configs/cm_x270_defconfig | 1 - arch/arm/configs/collie_defconfig | 1 - arch/arm/configs/corgi_defconfig | 1 - arch/arm/configs/ecbat91_defconfig | 1 - arch/arm/configs/em_x270_defconfig | 1 - arch/arm/configs/ep93xx_defconfig | 1 - arch/arm/configs/eseries_pxa_defconfig | 1 - arch/arm/configs/iop13xx_defconfig | 1 - arch/arm/configs/iop32x_defconfig | 1 - arch/arm/configs/iop33x_defconfig | 1 - arch/arm/configs/ixp2000_defconfig | 1 - arch/arm/configs/ixp23xx_defconfig | 1 - arch/arm/configs/kafa_defconfig | 1 - arch/arm/configs/kb9202_defconfig | 1 - arch/arm/configs/ks8695_defconfig | 1 - arch/arm/configs/lpd270_defconfig | 1 - arch/arm/configs/lpd7a404_defconfig | 1 - arch/arm/configs/netx_defconfig | 1 - arch/arm/configs/onearm_defconfig | 1 - arch/arm/configs/picotux200_defconfig | 1 - arch/arm/configs/pnx4008_defconfig | 1 - arch/arm/configs/realview-smp_defconfig | 1 - arch/arm/configs/realview_defconfig | 1 - arch/arm/configs/rpc_defconfig | 1 - arch/arm/configs/s3c2410_defconfig | 1 - arch/arm/configs/sam9_l9260_defconfig | 1 - arch/arm/configs/spitz_defconfig | 1 - arch/arm/configs/tct_hammer_defconfig | 1 - arch/arm/configs/trizeps4_defconfig | 1 - arch/arm/configs/versatile_defconfig | 1 - arch/arm/kernel/process.c | 4 +- arch/arm/kernel/time.c | 120 ------------------------------- arch/arm/mach-omap1/pm.c | 7 -- arch/arm/mach-omap2/pm.c | 7 -- include/asm-arm/dyntick.h | 6 -- include/asm-arm/hw_irq.h | 11 --- include/asm-arm/mach/time.h | 22 ------ 46 files changed, 1 insertion(+), 235 deletions(-) delete mode 100644 include/asm-arm/dyntick.h diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index b786e68914d4..167824e24edc 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -703,27 +703,6 @@ config PREEMPT Say Y here if you are building a kernel for a desktop, embedded or real-time system. Say N if you are unsure. -config NO_IDLE_HZ - bool "Dynamic tick timer" - depends on !GENERIC_CLOCKEVENTS - help - Select this option if you want to disable continuous timer ticks - and have them programmed to occur as required. This option saves - power as the system can remain in idle state for longer. - - By default dynamic tick is disabled during the boot, and can be - manually enabled with: - - echo 1 > /sys/devices/system/timer/timer0/dyn_tick - - Alternatively, if you want dynamic tick automatically enabled - during boot, pass "dyntick=enable" via the kernel command string. - - Please note that dynamic tick may affect the accuracy of - timekeeping on some platforms depending on the implementation. - Currently at least OMAP, PXA2xx and SA11x0 platforms are known - to have accurate timekeeping with dynamic tick. - config HZ int default 128 if ARCH_L7200 diff --git a/arch/arm/configs/at91cap9adk_defconfig b/arch/arm/configs/at91cap9adk_defconfig index e32e73648129..b8e73e95598d 100644 --- a/arch/arm/configs/at91cap9adk_defconfig +++ b/arch/arm/configs/at91cap9adk_defconfig @@ -213,7 +213,6 @@ CONFIG_CPU_CP15_MMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y diff --git a/arch/arm/configs/at91rm9200dk_defconfig b/arch/arm/configs/at91rm9200dk_defconfig index 2dbbbc3d4ac3..868fb7b9530b 100644 --- a/arch/arm/configs/at91rm9200dk_defconfig +++ b/arch/arm/configs/at91rm9200dk_defconfig @@ -169,7 +169,6 @@ CONFIG_AT91_CF=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y diff --git a/arch/arm/configs/at91rm9200ek_defconfig b/arch/arm/configs/at91rm9200ek_defconfig index 6e994f7820c6..de43fc675616 100644 --- a/arch/arm/configs/at91rm9200ek_defconfig +++ b/arch/arm/configs/at91rm9200ek_defconfig @@ -160,7 +160,6 @@ CONFIG_ISA_DMA_API=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y diff --git a/arch/arm/configs/at91sam9260ek_defconfig b/arch/arm/configs/at91sam9260ek_defconfig index f659c938473f..2011adfa6758 100644 --- a/arch/arm/configs/at91sam9260ek_defconfig +++ b/arch/arm/configs/at91sam9260ek_defconfig @@ -220,7 +220,6 @@ CONFIG_CPU_CP15_MMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/at91sam9261ek_defconfig b/arch/arm/configs/at91sam9261ek_defconfig index 3802e85f7483..4049768962d2 100644 --- a/arch/arm/configs/at91sam9261ek_defconfig +++ b/arch/arm/configs/at91sam9261ek_defconfig @@ -213,7 +213,6 @@ CONFIG_CPU_CP15_MMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/at91sam9263ek_defconfig b/arch/arm/configs/at91sam9263ek_defconfig index 32a0d74e0c89..fa1c5aecb5a8 100644 --- a/arch/arm/configs/at91sam9263ek_defconfig +++ b/arch/arm/configs/at91sam9263ek_defconfig @@ -213,7 +213,6 @@ CONFIG_CPU_CP15_MMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/at91sam9rlek_defconfig b/arch/arm/configs/at91sam9rlek_defconfig index 98e6746d02be..d8ec5f9ca6ec 100644 --- a/arch/arm/configs/at91sam9rlek_defconfig +++ b/arch/arm/configs/at91sam9rlek_defconfig @@ -211,7 +211,6 @@ CONFIG_CPU_CP15_MMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/ateb9200_defconfig b/arch/arm/configs/ateb9200_defconfig index d846a492e5ce..85c80f723d8e 100644 --- a/arch/arm/configs/ateb9200_defconfig +++ b/arch/arm/configs/ateb9200_defconfig @@ -171,7 +171,6 @@ CONFIG_AT91_CF=m # Kernel Features # CONFIG_PREEMPT=y -CONFIG_NO_IDLE_HZ=y CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/cm_x270_defconfig b/arch/arm/configs/cm_x270_defconfig index 5cab08397ae7..33b201c3b309 100644 --- a/arch/arm/configs/cm_x270_defconfig +++ b/arch/arm/configs/cm_x270_defconfig @@ -194,7 +194,6 @@ CONFIG_PCI_HOST_ITE8152=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/collie_defconfig b/arch/arm/configs/collie_defconfig index 4264e273202d..f7622e658163 100644 --- a/arch/arm/configs/collie_defconfig +++ b/arch/arm/configs/collie_defconfig @@ -166,7 +166,6 @@ CONFIG_PCMCIA_SA1100=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set CONFIG_ARCH_DISCONTIGMEM_ENABLE=y diff --git a/arch/arm/configs/corgi_defconfig b/arch/arm/configs/corgi_defconfig index e8980a9bb893..9b8748a8d9dd 100644 --- a/arch/arm/configs/corgi_defconfig +++ b/arch/arm/configs/corgi_defconfig @@ -165,7 +165,6 @@ CONFIG_PCMCIA_PXA2XX=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y diff --git a/arch/arm/configs/ecbat91_defconfig b/arch/arm/configs/ecbat91_defconfig index 90ed214e3673..cfeb817ad21a 100644 --- a/arch/arm/configs/ecbat91_defconfig +++ b/arch/arm/configs/ecbat91_defconfig @@ -230,7 +230,6 @@ CONFIG_AT91_CF=y # # CONFIG_TICK_ONESHOT is not set CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/em_x270_defconfig b/arch/arm/configs/em_x270_defconfig index 6bea0901bdf0..d3114c23603b 100644 --- a/arch/arm/configs/em_x270_defconfig +++ b/arch/arm/configs/em_x270_defconfig @@ -197,7 +197,6 @@ CONFIG_XSCALE_PMU=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y diff --git a/arch/arm/configs/ep93xx_defconfig b/arch/arm/configs/ep93xx_defconfig index 24a701ab33e5..21aa013793c6 100644 --- a/arch/arm/configs/ep93xx_defconfig +++ b/arch/arm/configs/ep93xx_defconfig @@ -184,7 +184,6 @@ CONFIG_ARM_AMBA=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/eseries_pxa_defconfig b/arch/arm/configs/eseries_pxa_defconfig index ed487b90dbed..493ecee24f94 100644 --- a/arch/arm/configs/eseries_pxa_defconfig +++ b/arch/arm/configs/eseries_pxa_defconfig @@ -251,7 +251,6 @@ CONFIG_PCMCIA_PXA2XX=m # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y diff --git a/arch/arm/configs/iop13xx_defconfig b/arch/arm/configs/iop13xx_defconfig index 988b4d13e76f..482e57061053 100644 --- a/arch/arm/configs/iop13xx_defconfig +++ b/arch/arm/configs/iop13xx_defconfig @@ -197,7 +197,6 @@ CONFIG_PCI_LEGACY=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/iop32x_defconfig b/arch/arm/configs/iop32x_defconfig index 83f40d4041a6..8612f58e1056 100644 --- a/arch/arm/configs/iop32x_defconfig +++ b/arch/arm/configs/iop32x_defconfig @@ -201,7 +201,6 @@ CONFIG_PCI_LEGACY=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/iop33x_defconfig b/arch/arm/configs/iop33x_defconfig index 917afb5ccfac..8b0098d19d08 100644 --- a/arch/arm/configs/iop33x_defconfig +++ b/arch/arm/configs/iop33x_defconfig @@ -197,7 +197,6 @@ CONFIG_PCI_LEGACY=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/ixp2000_defconfig b/arch/arm/configs/ixp2000_defconfig index f8f9793b526f..84680db6c615 100644 --- a/arch/arm/configs/ixp2000_defconfig +++ b/arch/arm/configs/ixp2000_defconfig @@ -184,7 +184,6 @@ CONFIG_PCI=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/ixp23xx_defconfig b/arch/arm/configs/ixp23xx_defconfig index 27cf022dd807..4a2f7b2372db 100644 --- a/arch/arm/configs/ixp23xx_defconfig +++ b/arch/arm/configs/ixp23xx_defconfig @@ -180,7 +180,6 @@ CONFIG_PCI=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/kafa_defconfig b/arch/arm/configs/kafa_defconfig index ae51a40db6f9..6dd95a2c8d5d 100644 --- a/arch/arm/configs/kafa_defconfig +++ b/arch/arm/configs/kafa_defconfig @@ -162,7 +162,6 @@ CONFIG_CPU_TLB_V4WBI=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/kb9202_defconfig b/arch/arm/configs/kb9202_defconfig index c16537d9d67a..8e74c66f239d 100644 --- a/arch/arm/configs/kb9202_defconfig +++ b/arch/arm/configs/kb9202_defconfig @@ -126,7 +126,6 @@ CONFIG_ISA_DMA_API=y # # Kernel Features # -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y diff --git a/arch/arm/configs/ks8695_defconfig b/arch/arm/configs/ks8695_defconfig index 8ab21a0719e9..6077f2cb88e4 100644 --- a/arch/arm/configs/ks8695_defconfig +++ b/arch/arm/configs/ks8695_defconfig @@ -174,7 +174,6 @@ CONFIG_PCCARD_NONSTATIC=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/lpd270_defconfig b/arch/arm/configs/lpd270_defconfig index a3bf5833b87a..1a38d8e3fe66 100644 --- a/arch/arm/configs/lpd270_defconfig +++ b/arch/arm/configs/lpd270_defconfig @@ -173,7 +173,6 @@ CONFIG_XSCALE_PMU=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/lpd7a404_defconfig b/arch/arm/configs/lpd7a404_defconfig index 46a0f7fe1fa5..7a2e932da1c6 100644 --- a/arch/arm/configs/lpd7a404_defconfig +++ b/arch/arm/configs/lpd7a404_defconfig @@ -148,7 +148,6 @@ CONFIG_ARM_AMBA=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set # CONFIG_AEABI is not set CONFIG_ARCH_DISCONTIGMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y diff --git a/arch/arm/configs/netx_defconfig b/arch/arm/configs/netx_defconfig index 57f32f39d0ff..0884f2370c3a 100644 --- a/arch/arm/configs/netx_defconfig +++ b/arch/arm/configs/netx_defconfig @@ -154,7 +154,6 @@ CONFIG_ARM_AMBA=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/onearm_defconfig b/arch/arm/configs/onearm_defconfig index 650a248613e5..418ca2febbe3 100644 --- a/arch/arm/configs/onearm_defconfig +++ b/arch/arm/configs/onearm_defconfig @@ -202,7 +202,6 @@ CONFIG_AT91_CF=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/picotux200_defconfig b/arch/arm/configs/picotux200_defconfig index 95a22f512805..14826f0dabde 100644 --- a/arch/arm/configs/picotux200_defconfig +++ b/arch/arm/configs/picotux200_defconfig @@ -201,7 +201,6 @@ CONFIG_ARM_THUMB=y # Kernel Features # # CONFIG_PREEMPT is not set -CONFIG_NO_IDLE_HZ=y CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y diff --git a/arch/arm/configs/pnx4008_defconfig b/arch/arm/configs/pnx4008_defconfig index b5e11aa2e290..811b8f60d19d 100644 --- a/arch/arm/configs/pnx4008_defconfig +++ b/arch/arm/configs/pnx4008_defconfig @@ -151,7 +151,6 @@ CONFIG_ARM_THUMB=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/realview-smp_defconfig b/arch/arm/configs/realview-smp_defconfig index fc39ba1a89f3..0c09b23167ec 100644 --- a/arch/arm/configs/realview-smp_defconfig +++ b/arch/arm/configs/realview-smp_defconfig @@ -177,7 +177,6 @@ CONFIG_NR_CPUS=4 CONFIG_HOTPLUG_CPU=y CONFIG_LOCAL_TIMERS=y # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/realview_defconfig b/arch/arm/configs/realview_defconfig index accbf529ce5b..907e54344dad 100644 --- a/arch/arm/configs/realview_defconfig +++ b/arch/arm/configs/realview_defconfig @@ -126,7 +126,6 @@ CONFIG_ISA_DMA_API=y # # Kernel Features # -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y diff --git a/arch/arm/configs/rpc_defconfig b/arch/arm/configs/rpc_defconfig index 5ddecb9ddf01..f62d1817d2c6 100644 --- a/arch/arm/configs/rpc_defconfig +++ b/arch/arm/configs/rpc_defconfig @@ -190,7 +190,6 @@ CONFIG_ISA_DMA_API=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig index f8a1645b3d4a..6d03763773bf 100644 --- a/arch/arm/configs/s3c2410_defconfig +++ b/arch/arm/configs/s3c2410_defconfig @@ -246,7 +246,6 @@ CONFIG_ISA=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=200 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/sam9_l9260_defconfig b/arch/arm/configs/sam9_l9260_defconfig index 484dc9739dfc..8688362bcf7b 100644 --- a/arch/arm/configs/sam9_l9260_defconfig +++ b/arch/arm/configs/sam9_l9260_defconfig @@ -211,7 +211,6 @@ CONFIG_ARM_THUMB=y # # CONFIG_TICK_ONESHOT is not set CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/spitz_defconfig b/arch/arm/configs/spitz_defconfig index aa7a01179500..7d59fb1f1cea 100644 --- a/arch/arm/configs/spitz_defconfig +++ b/arch/arm/configs/spitz_defconfig @@ -164,7 +164,6 @@ CONFIG_PCMCIA_PXA2XX=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y diff --git a/arch/arm/configs/tct_hammer_defconfig b/arch/arm/configs/tct_hammer_defconfig index 576b8339f0d6..07dfb98df4f0 100644 --- a/arch/arm/configs/tct_hammer_defconfig +++ b/arch/arm/configs/tct_hammer_defconfig @@ -247,7 +247,6 @@ CONFIG_ARM_THUMB=y # # CONFIG_TICK_ONESHOT is not set # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=200 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/configs/trizeps4_defconfig b/arch/arm/configs/trizeps4_defconfig index 6db6392806f9..8b7a431a8bfc 100644 --- a/arch/arm/configs/trizeps4_defconfig +++ b/arch/arm/configs/trizeps4_defconfig @@ -195,7 +195,6 @@ CONFIG_PCMCIA_PXA2XX=y # Kernel Features # CONFIG_PREEMPT=y -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y diff --git a/arch/arm/configs/versatile_defconfig b/arch/arm/configs/versatile_defconfig index 48dca69addae..8355f88f7292 100644 --- a/arch/arm/configs/versatile_defconfig +++ b/arch/arm/configs/versatile_defconfig @@ -151,7 +151,6 @@ CONFIG_ARM_AMBA=y # Kernel Features # # CONFIG_PREEMPT is not set -# CONFIG_NO_IDLE_HZ is not set CONFIG_HZ=100 # CONFIG_AEABI is not set # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 46bf2ede6128..199b3680118b 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -133,10 +133,8 @@ static void default_idle(void) cpu_relax(); else { local_irq_disable(); - if (!need_resched()) { - timer_dyn_reprogram(); + if (!need_resched()) arch_idle(); - } local_irq_enable(); } } diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c index b5867eca1d0b..cc5145b28e7f 100644 --- a/arch/arm/kernel/time.c +++ b/arch/arm/kernel/time.c @@ -365,108 +365,6 @@ static struct sysdev_class timer_sysclass = { .resume = timer_resume, }; -#ifdef CONFIG_NO_IDLE_HZ -static int timer_dyn_tick_enable(void) -{ - struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick; - unsigned long flags; - int ret = -ENODEV; - - if (dyn_tick) { - spin_lock_irqsave(&dyn_tick->lock, flags); - ret = 0; - if (!(dyn_tick->state & DYN_TICK_ENABLED)) { - ret = dyn_tick->enable(); - - if (ret == 0) - dyn_tick->state |= DYN_TICK_ENABLED; - } - spin_unlock_irqrestore(&dyn_tick->lock, flags); - } - - return ret; -} - -static int timer_dyn_tick_disable(void) -{ - struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick; - unsigned long flags; - int ret = -ENODEV; - - if (dyn_tick) { - spin_lock_irqsave(&dyn_tick->lock, flags); - ret = 0; - if (dyn_tick->state & DYN_TICK_ENABLED) { - ret = dyn_tick->disable(); - - if (ret == 0) - dyn_tick->state &= ~DYN_TICK_ENABLED; - } - spin_unlock_irqrestore(&dyn_tick->lock, flags); - } - - return ret; -} - -/* - * Reprogram the system timer for at least the calculated time interval. - * This function should be called from the idle thread with IRQs disabled, - * immediately before sleeping. - */ -void timer_dyn_reprogram(void) -{ - struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick; - unsigned long next, seq, flags; - - if (!dyn_tick) - return; - - spin_lock_irqsave(&dyn_tick->lock, flags); - if (dyn_tick->state & DYN_TICK_ENABLED) { - next = next_timer_interrupt(); - do { - seq = read_seqbegin(&xtime_lock); - dyn_tick->reprogram(next - jiffies); - } while (read_seqretry(&xtime_lock, seq)); - } - spin_unlock_irqrestore(&dyn_tick->lock, flags); -} - -static ssize_t timer_show_dyn_tick(struct sys_device *dev, char *buf) -{ - return sprintf(buf, "%i\n", - (system_timer->dyn_tick->state & DYN_TICK_ENABLED) >> 1); -} - -static ssize_t timer_set_dyn_tick(struct sys_device *dev, const char *buf, - size_t count) -{ - unsigned int enable = simple_strtoul(buf, NULL, 2); - - if (enable) - timer_dyn_tick_enable(); - else - timer_dyn_tick_disable(); - - return count; -} -static SYSDEV_ATTR(dyn_tick, 0644, timer_show_dyn_tick, timer_set_dyn_tick); - -/* - * dyntick=enable|disable - */ -static char dyntick_str[4] __initdata = ""; - -static int __init dyntick_setup(char *str) -{ - if (str) - strlcpy(dyntick_str, str, sizeof(dyntick_str)); - return 1; -} - -__setup("dyntick=", dyntick_setup); -#endif - static int __init timer_init_sysfs(void) { int ret = sysdev_class_register(&timer_sysclass); @@ -475,19 +373,6 @@ static int __init timer_init_sysfs(void) ret = sysdev_register(&system_timer->dev); } -#ifdef CONFIG_NO_IDLE_HZ - if (ret == 0 && system_timer->dyn_tick) { - ret = sysdev_create_file(&system_timer->dev, &attr_dyn_tick); - - /* - * Turn on dynamic tick after calibrate delay - * for correct bogomips - */ - if (ret == 0 && dyntick_str[0] == 'e') - ret = timer_dyn_tick_enable(); - } -#endif - return ret; } @@ -500,10 +385,5 @@ void __init time_init(void) system_timer->offset = dummy_gettimeoffset; #endif system_timer->init(); - -#ifdef CONFIG_NO_IDLE_HZ - if (system_timer->dyn_tick) - spin_lock_init(&system_timer->dyn_tick->lock); -#endif } diff --git a/arch/arm/mach-omap1/pm.c b/arch/arm/mach-omap1/pm.c index e6c64e10b7ec..742f79e73bd7 100644 --- a/arch/arm/mach-omap1/pm.c +++ b/arch/arm/mach-omap1/pm.c @@ -116,13 +116,6 @@ void omap_pm_idle(void) return; } - /* - * Since an interrupt may set up a timer, we don't want to - * reprogram the hardware timer with interrupts enabled. - * Re-enable interrupts only after returning from idle. - */ - timer_dyn_reprogram(); - #ifdef CONFIG_OMAP_MPU_TIMER #warning Enable 32kHz OS timer in order to allow sleep states in idle use_idlect1 = use_idlect1 & ~(1 << 9); diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index aad781dcf1b1..d6c9de82ca0c 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -57,13 +57,6 @@ void omap2_pm_idle(void) return; } - /* - * Since an interrupt may set up a timer, we don't want to - * reprogram the hardware timer with interrupts enabled. - * Re-enable interrupts only after returning from idle. - */ - timer_dyn_reprogram(); - omap2_sram_idle(); local_fiq_enable(); local_irq_enable(); diff --git a/include/asm-arm/dyntick.h b/include/asm-arm/dyntick.h deleted file mode 100644 index 19fab2d2b760..000000000000 --- a/include/asm-arm/dyntick.h +++ /dev/null @@ -1,6 +0,0 @@ -#ifndef _ASMARM_DYNTICK_H -#define _ASMARM_DYNTICK_H - -#include - -#endif /* _ASMARM_DYNTICK_H */ diff --git a/include/asm-arm/hw_irq.h b/include/asm-arm/hw_irq.h index 98d594a973d6..f1a08a500604 100644 --- a/include/asm-arm/hw_irq.h +++ b/include/asm-arm/hw_irq.h @@ -6,15 +6,4 @@ #include -#if defined(CONFIG_NO_IDLE_HZ) -# include -# define handle_dynamic_tick(action) \ - if (!(action->flags & IRQF_TIMER) && system_timer->dyn_tick) { \ - write_seqlock(&xtime_lock); \ - if (system_timer->dyn_tick->state & DYN_TICK_ENABLED) \ - system_timer->dyn_tick->handler(irq, NULL); \ - write_sequnlock(&xtime_lock); \ - } -#endif - #endif diff --git a/include/asm-arm/mach/time.h b/include/asm-arm/mach/time.h index 5dc357013b79..2fd36ea0130d 100644 --- a/include/asm-arm/mach/time.h +++ b/include/asm-arm/mach/time.h @@ -41,30 +41,8 @@ struct sys_timer { #ifndef CONFIG_GENERIC_TIME unsigned long (*offset)(void); #endif - -#ifdef CONFIG_NO_IDLE_HZ - struct dyn_tick_timer *dyn_tick; -#endif -}; - -#ifdef CONFIG_NO_IDLE_HZ - -#define DYN_TICK_ENABLED (1 << 1) - -struct dyn_tick_timer { - spinlock_t lock; - unsigned int state; /* Current state */ - int (*enable)(void); /* Enables dynamic tick */ - int (*disable)(void); /* Disables dynamic tick */ - void (*reprogram)(unsigned long); /* Reprograms the timer */ - int (*handler)(int, void *); }; -void timer_dyn_reprogram(void); -#else -#define timer_dyn_reprogram() do { } while (0) -#endif - extern struct sys_timer *system_timer; extern void timer_tick(void); -- cgit v1.2.3 From ee9c578527a93c66becb526c4a122c5358a959c5 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 13:59:33 +0100 Subject: dyntick: Remove last reminants of dyntick support Remove the last reminants of dyntick support from the generic kernel. Signed-off-by: Russell King --- kernel/hrtimer.c | 2 +- kernel/sysctl.c | 12 ------------ kernel/timer.c | 10 +--------- 3 files changed, 2 insertions(+), 22 deletions(-) diff --git a/kernel/hrtimer.c b/kernel/hrtimer.c index 421be5fe5cc7..543d9ca9b4f4 100644 --- a/kernel/hrtimer.c +++ b/kernel/hrtimer.c @@ -1078,7 +1078,7 @@ ktime_t hrtimer_get_remaining(const struct hrtimer *timer) } EXPORT_SYMBOL_GPL(hrtimer_get_remaining); -#if defined(CONFIG_NO_IDLE_HZ) || defined(CONFIG_NO_HZ) +#ifdef CONFIG_NO_HZ /** * hrtimer_get_next_event - get the time until next expiry event * diff --git a/kernel/sysctl.c b/kernel/sysctl.c index d7ffdc59816a..76426d930077 100644 --- a/kernel/sysctl.c +++ b/kernel/sysctl.c @@ -131,8 +131,6 @@ extern int sysctl_userprocess_debug; extern int spin_retry; #endif -extern int sysctl_hz_timer; - #ifdef CONFIG_BSD_PROCESS_ACCT extern int acct_parm[]; #endif @@ -561,16 +559,6 @@ static struct ctl_table kern_table[] = { .mode = 0644, .proc_handler = &proc_dointvec, }, -#endif -#ifdef CONFIG_NO_IDLE_HZ - { - .ctl_name = KERN_HZ_TIMER, - .procname = "hz_timer", - .data = &sysctl_hz_timer, - .maxlen = sizeof(int), - .mode = 0644, - .proc_handler = &proc_dointvec, - }, #endif { .ctl_name = KERN_S390_USER_DEBUG_LOGGING, diff --git a/kernel/timer.c b/kernel/timer.c index ceacc6626572..ef3fa6906e8f 100644 --- a/kernel/timer.c +++ b/kernel/timer.c @@ -812,7 +812,7 @@ static inline void __run_timers(struct tvec_base *base) spin_unlock_irq(&base->lock); } -#if defined(CONFIG_NO_IDLE_HZ) || defined(CONFIG_NO_HZ) +#ifdef CONFIG_NO_HZ /* * Find out when the next timer event is due to happen. This * is used on S/390 to stop all activity when a cpus is idle. @@ -947,14 +947,6 @@ unsigned long get_next_timer_interrupt(unsigned long now) return cmp_next_hrtimer_event(now, expires); } - -#ifdef CONFIG_NO_IDLE_HZ -unsigned long next_timer_interrupt(void) -{ - return get_next_timer_interrupt(jiffies); -} -#endif - #endif #ifndef CONFIG_VIRT_CPU_ACCOUNTING -- cgit v1.2.3 From 150c9173031d43746d70582a17931350f3da8932 Mon Sep 17 00:00:00 2001 From: Russell King Date: Mon, 12 May 2008 17:37:21 +0100 Subject: dyntick: remove deferences from SH SH does not have a configuration option for NO_IDLE_HZ their Kconfig files, yet their defconfig files lists them. Remove those references. Signed-off-by: Russell King --- arch/sh/configs/landisk_defconfig | 1 - arch/sh/configs/lboxre2_defconfig | 1 - arch/sh/configs/se7705_defconfig | 1 - arch/sh/configs/se7712_defconfig | 1 - arch/sh/configs/se7750_defconfig | 1 - 5 files changed, 5 deletions(-) diff --git a/arch/sh/configs/landisk_defconfig b/arch/sh/configs/landisk_defconfig index f52db125432f..38f934ab50c7 100644 --- a/arch/sh/configs/landisk_defconfig +++ b/arch/sh/configs/landisk_defconfig @@ -226,7 +226,6 @@ CONFIG_CPU_HAS_PTEA=y # CONFIG_SH_TMU=y CONFIG_SH_TIMER_IRQ=16 -# CONFIG_NO_IDLE_HZ is not set CONFIG_SH_PCLK_FREQ=33333333 # diff --git a/arch/sh/configs/lboxre2_defconfig b/arch/sh/configs/lboxre2_defconfig index 9fa66d92a4e7..b68b6cdbb78f 100644 --- a/arch/sh/configs/lboxre2_defconfig +++ b/arch/sh/configs/lboxre2_defconfig @@ -231,7 +231,6 @@ CONFIG_CPU_HAS_PTEA=y # CONFIG_SH_TMU=y CONFIG_SH_TIMER_IRQ=16 -# CONFIG_NO_IDLE_HZ is not set CONFIG_SH_PCLK_FREQ=40000000 # diff --git a/arch/sh/configs/se7705_defconfig b/arch/sh/configs/se7705_defconfig index 84717d854867..490dcbc2ce33 100644 --- a/arch/sh/configs/se7705_defconfig +++ b/arch/sh/configs/se7705_defconfig @@ -239,7 +239,6 @@ CONFIG_CPU_HAS_SR_RB=y # CONFIG_SH_TMU=y CONFIG_SH_TIMER_IRQ=16 -# CONFIG_NO_IDLE_HZ is not set CONFIG_SH_PCLK_FREQ=33333333 # diff --git a/arch/sh/configs/se7712_defconfig b/arch/sh/configs/se7712_defconfig index 240a1cef69aa..2dd83af988f0 100644 --- a/arch/sh/configs/se7712_defconfig +++ b/arch/sh/configs/se7712_defconfig @@ -236,7 +236,6 @@ CONFIG_CPU_HAS_SR_RB=y # CONFIG_SH_TMU=y CONFIG_SH_TIMER_IRQ=16 -# CONFIG_NO_IDLE_HZ is not set CONFIG_SH_PCLK_FREQ=66666666 # diff --git a/arch/sh/configs/se7750_defconfig b/arch/sh/configs/se7750_defconfig index c60b6fd4fc42..167786f9a9bd 100644 --- a/arch/sh/configs/se7750_defconfig +++ b/arch/sh/configs/se7750_defconfig @@ -235,7 +235,6 @@ CONFIG_CPU_HAS_PTEA=y # CONFIG_SH_TMU=y CONFIG_SH_TIMER_IRQ=16 -# CONFIG_NO_IDLE_HZ is not set CONFIG_SH_PCLK_FREQ=33333333 # -- cgit v1.2.3 From 1a189b97190d3f0f8cf0379a799d3555b2d648bb Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 13 Apr 2008 21:41:55 +0100 Subject: [ARM] pxa: Add bare bones PWM API Signed-off-by: Russell King --- arch/arm/Kconfig | 3 +++ include/linux/pwm.h | 31 +++++++++++++++++++++++++++++++ 2 files changed, 34 insertions(+) create mode 100644 include/linux/pwm.h diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index b786e68914d4..c274dbb89a83 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -22,6 +22,9 @@ config ARM Europe. There is an ARM Linux project with a web page at . +config HAVE_PWM + bool + config SYS_SUPPORTS_APM_EMULATION bool diff --git a/include/linux/pwm.h b/include/linux/pwm.h new file mode 100644 index 000000000000..3945f803d514 --- /dev/null +++ b/include/linux/pwm.h @@ -0,0 +1,31 @@ +#ifndef __LINUX_PWM_H +#define __LINUX_PWM_H + +struct pwm_device; + +/* + * pwm_request - request a PWM device + */ +struct pwm_device *pwm_request(int pwm_id, const char *label); + +/* + * pwm_free - free a PWM device + */ +void pwm_free(struct pwm_device *pwm); + +/* + * pwm_config - change a PWM device configuration + */ +int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns); + +/* + * pwm_enable - start a PWM output toggling + */ +int pwm_enable(struct pwm_device *pwm); + +/* + * pwm_disable - stop a PWM output toggling + */ +void pwm_disable(struct pwm_device *pwm); + +#endif /* __ASM_ARCH_PWM_H */ -- cgit v1.2.3 From 75540c1ac3c7bd72ac8e092058f9714875239995 Mon Sep 17 00:00:00 2001 From: eric miao Date: Sun, 13 Apr 2008 21:44:04 +0100 Subject: [ARM] pxa: Add PXA support for PWM API Patch mainly from Eric Miao, with minor edits by rmk. Note: PWM0 and PWM2 share the same register I/O space and clock gating on pxa{27x, 3xx}, thus PWM2 is treated in the driver as a child PWM of PWM0. And this is also true for PWM1/3. Signed-off-by: eric miao Signed-off-by: Russell King --- arch/arm/mach-pxa/Kconfig | 5 + arch/arm/mach-pxa/Makefile | 1 + arch/arm/mach-pxa/devices.c | 60 +++++++++ arch/arm/mach-pxa/devices.h | 5 + arch/arm/mach-pxa/pwm.c | 299 ++++++++++++++++++++++++++++++++++++++++++++ arch/arm/mach-pxa/pxa25x.c | 6 +- arch/arm/mach-pxa/pxa27x.c | 5 +- arch/arm/mach-pxa/pxa3xx.c | 4 + 8 files changed, 382 insertions(+), 3 deletions(-) create mode 100644 arch/arm/mach-pxa/pwm.c diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index 5da7a6820492..9c01505b1825 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -273,4 +273,9 @@ config PXA_SSP tristate help Enable support for PXA2xx SSP ports + +config PXA_PWM + tristate + help + Enable support for PXA2xx/PXA3xx PWM controllers endif diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile index 0e6d05bb81aa..02cbc3cfbe01 100644 --- a/arch/arm/mach-pxa/Makefile +++ b/arch/arm/mach-pxa/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_CPU_FREQ) += cpu-pxa.o # Generic drivers that other drivers may depend upon obj-$(CONFIG_PXA_SSP) += ssp.o +obj-$(CONFIG_PXA_PWM) += pwm.o # SoC-specific code obj-$(CONFIG_PXA25x) += mfp-pxa2xx.o pxa25x.o diff --git a/arch/arm/mach-pxa/devices.c b/arch/arm/mach-pxa/devices.c index d6c05b6eab35..794a1076db73 100644 --- a/arch/arm/mach-pxa/devices.c +++ b/arch/arm/mach-pxa/devices.c @@ -280,6 +280,36 @@ struct platform_device pxa_device_rtc = { #ifdef CONFIG_PXA25x +static struct resource pxa25x_resource_pwm0[] = { + [0] = { + .start = 0x40b00000, + .end = 0x40b0000f, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device pxa25x_device_pwm0 = { + .name = "pxa25x-pwm", + .id = 0, + .resource = pxa25x_resource_pwm0, + .num_resources = ARRAY_SIZE(pxa25x_resource_pwm0), +}; + +static struct resource pxa25x_resource_pwm1[] = { + [0] = { + .start = 0x40c00000, + .end = 0x40c0000f, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device pxa25x_device_pwm1 = { + .name = "pxa25x-pwm", + .id = 1, + .resource = pxa25x_resource_pwm1, + .num_resources = ARRAY_SIZE(pxa25x_resource_pwm1), +}; + static u64 pxa25x_ssp_dma_mask = DMA_BIT_MASK(32); static struct resource pxa25x_resource_ssp[] = { @@ -568,6 +598,36 @@ struct platform_device pxa27x_device_ssp3 = { .num_resources = ARRAY_SIZE(pxa27x_resource_ssp3), }; +static struct resource pxa27x_resource_pwm0[] = { + [0] = { + .start = 0x40b00000, + .end = 0x40b0001f, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device pxa27x_device_pwm0 = { + .name = "pxa27x-pwm", + .id = 0, + .resource = pxa27x_resource_pwm0, + .num_resources = ARRAY_SIZE(pxa27x_resource_pwm0), +}; + +static struct resource pxa27x_resource_pwm1[] = { + [0] = { + .start = 0x40c00000, + .end = 0x40c0001f, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device pxa27x_device_pwm1 = { + .name = "pxa27x-pwm", + .id = 1, + .resource = pxa27x_resource_pwm1, + .num_resources = ARRAY_SIZE(pxa27x_resource_pwm1), +}; + static struct resource pxa27x_resource_camera[] = { [0] = { .start = 0x50000000, diff --git a/arch/arm/mach-pxa/devices.h b/arch/arm/mach-pxa/devices.h index fcab017f27ee..e620a3373d42 100644 --- a/arch/arm/mach-pxa/devices.h +++ b/arch/arm/mach-pxa/devices.h @@ -24,4 +24,9 @@ extern struct platform_device pxa27x_device_ssp2; extern struct platform_device pxa27x_device_ssp3; extern struct platform_device pxa3xx_device_ssp4; +extern struct platform_device pxa25x_device_pwm0; +extern struct platform_device pxa25x_device_pwm1; +extern struct platform_device pxa27x_device_pwm0; +extern struct platform_device pxa27x_device_pwm1; + void __init pxa_register_device(struct platform_device *dev, void *data); diff --git a/arch/arm/mach-pxa/pwm.c b/arch/arm/mach-pxa/pwm.c new file mode 100644 index 000000000000..70fb3ca6a058 --- /dev/null +++ b/arch/arm/mach-pxa/pwm.c @@ -0,0 +1,299 @@ +/* + * linux/arch/arm/mach-pxa/pwm.c + * + * simple driver for PWM (Pulse Width Modulator) controller + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * 2008-02-13 initial version + * eric miao + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +/* PWM registers and bits definitions */ +#define PWMCR (0x00) +#define PWMDCR (0x04) +#define PWMPCR (0x08) + +#define PWMCR_SD (1 << 6) +#define PWMDCR_FD (1 << 10) + +struct pwm_device { + struct list_head node; + struct platform_device *pdev; + + const char *label; + struct clk *clk; + void __iomem *mmio_base; + + unsigned int use_count; + unsigned int pwm_id; +}; + +/* + * period_ns = 10^9 * (PRESCALE + 1) * (PV + 1) / PWM_CLK_RATE + * duty_ns = 10^9 * (PRESCALE + 1) * DC / PWM_CLK_RATE + */ +int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns) +{ + unsigned long long c; + unsigned long period_cycles, prescale, pv, dc; + + if (pwm == NULL || period_ns == 0 || duty_ns > period_ns) + return -EINVAL; + + c = clk_get_rate(pwm->clk); + c = c * period_ns; + do_div(c, 1000000000); + period_cycles = c; + + if (period_cycles < 0) + period_cycles = 1; + prescale = (period_cycles - 1) / 1024; + pv = period_cycles / (prescale + 1) - 1; + + if (prescale > 63) + return -EINVAL; + + if (duty_ns == period_ns) + dc = PWMDCR_FD; + else + dc = (pv + 1) * duty_ns / period_ns; + + /* NOTE: the clock to PWM has to be enabled first + * before writing to the registers + */ + clk_enable(pwm->clk); + __raw_writel(prescale, pwm->mmio_base + PWMCR); + __raw_writel(dc, pwm->mmio_base + PWMDCR); + __raw_writel(pv, pwm->mmio_base + PWMPCR); + clk_disable(pwm->clk); + + return 0; +} +EXPORT_SYMBOL(pwm_config); + +int pwm_enable(struct pwm_device *pwm) +{ + return clk_enable(pwm->clk); +} +EXPORT_SYMBOL(pwm_enable); + +void pwm_disable(struct pwm_device *pwm) +{ + clk_disable(pwm->clk); +} +EXPORT_SYMBOL(pwm_disable); + +static DEFINE_MUTEX(pwm_lock); +static LIST_HEAD(pwm_list); + +struct pwm_device *pwm_request(int pwm_id, const char *label) +{ + struct pwm_device *pwm; + int found = 0; + + mutex_lock(&pwm_lock); + + list_for_each_entry(pwm, &pwm_list, node) { + if (pwm->pwm_id == pwm_id && pwm->use_count == 0) { + pwm->use_count++; + pwm->label = label; + found = 1; + break; + } + } + + mutex_unlock(&pwm_lock); + + return (found) ? pwm : NULL; +} +EXPORT_SYMBOL(pwm_request); + +void pwm_free(struct pwm_device *pwm) +{ + mutex_lock(&pwm_lock); + + if (pwm->use_count) { + pwm->use_count--; + pwm->label = NULL; + } else + pr_warning("PWM device already freed\n"); + + mutex_unlock(&pwm_lock); +} +EXPORT_SYMBOL(pwm_free); + +static inline void __add_pwm(struct pwm_device *pwm) +{ + mutex_lock(&pwm_lock); + list_add_tail(&pwm->node, &pwm_list); + mutex_unlock(&pwm_lock); +} + +static struct pwm_device *pwm_probe(struct platform_device *pdev, + unsigned int pwm_id, struct pwm_device *parent_pwm) +{ + struct pwm_device *pwm; + struct resource *r; + int ret = 0; + + pwm = kzalloc(sizeof(struct pwm_device), GFP_KERNEL); + if (pwm == NULL) { + dev_err(&pdev->dev, "failed to allocate memory\n"); + return ERR_PTR(-ENOMEM); + } + + pwm->clk = clk_get(&pdev->dev, "PWMCLK"); + if (IS_ERR(pwm->clk)) { + ret = PTR_ERR(pwm->clk); + goto err_free; + } + + pwm->use_count = 0; + pwm->pwm_id = pwm_id; + pwm->pdev = pdev; + + if (parent_pwm != NULL) { + /* registers for the second PWM has offset of 0x10 */ + pwm->mmio_base = parent_pwm->mmio_base + 0x10; + __add_pwm(pwm); + return pwm; + } + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (r == NULL) { + dev_err(&pdev->dev, "no memory resource defined\n"); + ret = -ENODEV; + goto err_free_clk; + } + + r = request_mem_region(r->start, r->end - r->start + 1, pdev->name); + if (r == NULL) { + dev_err(&pdev->dev, "failed to request memory resource\n"); + ret = -EBUSY; + goto err_free_clk; + } + + pwm->mmio_base = ioremap(r->start, r->end - r->start + 1); + if (pwm->mmio_base == NULL) { + dev_err(&pdev->dev, "failed to ioremap() registers\n"); + ret = -ENODEV; + goto err_free_mem; + } + + __add_pwm(pwm); + platform_set_drvdata(pdev, pwm); + return pwm; + +err_free_mem: + release_mem_region(r->start, r->end - r->start + 1); +err_free_clk: + clk_put(pwm->clk); +err_free: + kfree(pwm); + return ERR_PTR(ret); +} + +static int __devinit pxa25x_pwm_probe(struct platform_device *pdev) +{ + struct pwm_device *pwm = pwm_probe(pdev, pdev->id, NULL); + + if (IS_ERR(pwm)) + return PTR_ERR(pwm); + + return 0; +} + +static int __devinit pxa27x_pwm_probe(struct platform_device *pdev) +{ + struct pwm_device *pwm; + + pwm = pwm_probe(pdev, pdev->id * 2, NULL); + if (IS_ERR(pwm)) + return PTR_ERR(pwm); + + pwm = pwm_probe(pdev, pdev->id * 2 + 1, pwm); + if (IS_ERR(pwm)) + return PTR_ERR(pwm); + + return 0; +} + +static int __devexit pwm_remove(struct platform_device *pdev) +{ + struct pwm_device *pwm; + struct resource *r; + + pwm = platform_get_drvdata(pdev); + if (pwm == NULL) + return -ENODEV; + + mutex_lock(&pwm_lock); + list_del(&pwm->node); + mutex_unlock(&pwm_lock); + + iounmap(pwm->mmio_base); + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(r->start, r->end - r->start + 1); + + clk_put(pwm->clk); + kfree(pwm); + return 0; +} + +static struct platform_driver pxa25x_pwm_driver = { + .driver = { + .name = "pxa25x-pwm", + }, + .probe = pxa25x_pwm_probe, + .remove = __devexit_p(pwm_remove), +}; + +static struct platform_driver pxa27x_pwm_driver = { + .driver = { + .name = "pxa27x-pwm", + }, + .probe = pxa27x_pwm_probe, + .remove = __devexit_p(pwm_remove), +}; + +static int __init pwm_init(void) +{ + int ret = 0; + + ret = platform_driver_register(&pxa25x_pwm_driver); + if (ret) { + printk(KERN_ERR "failed to register pxa25x_pwm_driver\n"); + return ret; + } + + ret = platform_driver_register(&pxa27x_pwm_driver); + if (ret) { + printk(KERN_ERR "failed to register pxa27x_pwm_driver\n"); + return ret; + } + + return ret; +} +arch_initcall(pwm_init); + +static void __exit pwm_exit(void) +{ + platform_driver_unregister(&pxa25x_pwm_driver); + platform_driver_unregister(&pxa27x_pwm_driver); +} +module_exit(pwm_exit); diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c index e5b417d14bb0..2bed3f98d41c 100644 --- a/arch/arm/mach-pxa/pxa25x.c +++ b/arch/arm/mach-pxa/pxa25x.c @@ -129,12 +129,12 @@ static struct clk pxa25x_clks[] = { INIT_CKEN("SSPCLK", SSP, 3686400, 0, &pxa25x_device_ssp.dev), INIT_CKEN("SSPCLK", NSSP, 3686400, 0, &pxa25x_device_nssp.dev), INIT_CKEN("SSPCLK", ASSP, 3686400, 0, &pxa25x_device_assp.dev), + INIT_CKEN("PWMCLK", PWM0, 3686400, 0, &pxa25x_device_pwm0.dev), + INIT_CKEN("PWMCLK", PWM1, 3686400, 0, &pxa25x_device_pwm1.dev), INIT_CKEN("AC97CLK", AC97, 24576000, 0, NULL), /* - INIT_CKEN("PWMCLK", PWM0, 3686400, 0, NULL), - INIT_CKEN("PWMCLK", PWM0, 3686400, 0, NULL), INIT_CKEN("I2SCLK", I2S, 14745600, 0, NULL), */ INIT_CKEN("FICPCLK", FICP, 47923000, 0, NULL), @@ -269,6 +269,8 @@ static struct platform_device *pxa25x_devices[] __initdata = { &pxa25x_device_ssp, &pxa25x_device_nssp, &pxa25x_device_assp, + &pxa25x_device_pwm0, + &pxa25x_device_pwm1, }; static struct sys_device pxa25x_sysdev[] = { diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c index 7e945836e129..bc2e80f69673 100644 --- a/arch/arm/mach-pxa/pxa27x.c +++ b/arch/arm/mach-pxa/pxa27x.c @@ -157,12 +157,13 @@ static struct clk pxa27x_clks[] = { INIT_CKEN("SSPCLK", SSP1, 13000000, 0, &pxa27x_device_ssp1.dev), INIT_CKEN("SSPCLK", SSP2, 13000000, 0, &pxa27x_device_ssp2.dev), INIT_CKEN("SSPCLK", SSP3, 13000000, 0, &pxa27x_device_ssp3.dev), + INIT_CKEN("PWMCLK", PWM0, 13000000, 0, &pxa27x_device_pwm0.dev), + INIT_CKEN("PWMCLK", PWM1, 13000000, 0, &pxa27x_device_pwm1.dev), INIT_CKEN("AC97CLK", AC97, 24576000, 0, NULL), INIT_CKEN("AC97CONFCLK", AC97CONF, 24576000, 0, NULL), /* - INIT_CKEN("PWMCLK", PWM0, 13000000, 0, NULL), INIT_CKEN("MSLCLK", MSL, 48000000, 0, NULL), INIT_CKEN("USIMCLK", USIM, 48000000, 0, NULL), INIT_CKEN("MSTKCLK", MEMSTK, 19500000, 0, NULL), @@ -363,6 +364,8 @@ static struct platform_device *devices[] __initdata = { &pxa27x_device_ssp1, &pxa27x_device_ssp2, &pxa27x_device_ssp3, + &pxa27x_device_pwm0, + &pxa27x_device_pwm1, }; static struct sys_device pxa27x_sysdev[] = { diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c index 644550bfa330..0f717df1fdb2 100644 --- a/arch/arm/mach-pxa/pxa3xx.c +++ b/arch/arm/mach-pxa/pxa3xx.c @@ -239,6 +239,8 @@ static struct clk pxa3xx_clks[] = { PXA3xx_CKEN("SSPCLK", SSP2, 13000000, 0, &pxa27x_device_ssp2.dev), PXA3xx_CKEN("SSPCLK", SSP3, 13000000, 0, &pxa27x_device_ssp3.dev), PXA3xx_CKEN("SSPCLK", SSP4, 13000000, 0, &pxa3xx_device_ssp4.dev), + PXA3xx_CKEN("PWMCLK", PWM0, 13000000, 0, &pxa27x_device_pwm0.dev), + PXA3xx_CKEN("PWMCLK", PWM1, 13000000, 0, &pxa27x_device_pwm1.dev), PXA3xx_CKEN("MMCCLK", MMC1, 19500000, 0, &pxa_device_mci.dev), PXA3xx_CKEN("MMCCLK", MMC2, 19500000, 0, &pxa3xx_device_mci2.dev), @@ -530,6 +532,8 @@ static struct platform_device *devices[] __initdata = { &pxa27x_device_ssp2, &pxa27x_device_ssp3, &pxa3xx_device_ssp4, + &pxa27x_device_pwm0, + &pxa27x_device_pwm1, }; static struct sys_device pxa3xx_sysdev[] = { -- cgit v1.2.3 From 02a8e76979f9b439642e67955edb865c112926f6 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 17:15:32 +0100 Subject: [ARM] pxa: corgibl_limit_intensity build errors If CONFIG_BACKLIGHT_CORGI is not selected, then corgibl_limit_intensity() is not present. However, both corgi_pm.c and sharp_pm.c reference this symbol, resulting in a link error. Wrap the references with the relevant ifdefs, and avoid the resulting NULL pointer dereference by making the code in sharpsl_pm.c also conditional on the config symbol. Signed-off-by: Russell King --- arch/arm/common/sharpsl_pm.c | 2 ++ arch/arm/mach-pxa/corgi_pm.c | 2 ++ arch/arm/mach-pxa/spitz_pm.c | 2 ++ 3 files changed, 6 insertions(+) diff --git a/arch/arm/common/sharpsl_pm.c b/arch/arm/common/sharpsl_pm.c index 5bba5255b119..5736c987c80d 100644 --- a/arch/arm/common/sharpsl_pm.c +++ b/arch/arm/common/sharpsl_pm.c @@ -157,6 +157,7 @@ static void sharpsl_battery_thread(struct work_struct *private_) dev_dbg(sharpsl_pm.dev, "Battery: voltage: %d, status: %d, percentage: %d, time: %ld\n", voltage, sharpsl_pm.battstat.mainbat_status, sharpsl_pm.battstat.mainbat_percent, jiffies); +#ifdef CONFIG_BACKLIGHT_CORGI /* If battery is low. limit backlight intensity to save power. */ if ((sharpsl_pm.battstat.ac_status != APM_AC_ONLINE) && ((sharpsl_pm.battstat.mainbat_status == APM_BATTERY_STATUS_LOW) || @@ -169,6 +170,7 @@ static void sharpsl_battery_thread(struct work_struct *private_) sharpsl_pm.machinfo->backlight_limit(0); sharpsl_pm.flags &= ~SHARPSL_BL_LIMIT; } +#endif /* Suspend if critical battery level */ if ((sharpsl_pm.battstat.ac_status != APM_AC_ONLINE) diff --git a/arch/arm/mach-pxa/corgi_pm.c b/arch/arm/mach-pxa/corgi_pm.c index 0a85f706e887..ae91c4b1135c 100644 --- a/arch/arm/mach-pxa/corgi_pm.c +++ b/arch/arm/mach-pxa/corgi_pm.c @@ -204,7 +204,9 @@ static struct sharpsl_charger_machinfo corgi_pm_machinfo = { .read_devdata = corgipm_read_devdata, .charger_wakeup = corgi_charger_wakeup, .should_wakeup = corgi_should_wakeup, +#ifdef CONFIG_BACKLIGHT_CORGI .backlight_limit = corgibl_limit_intensity, +#endif .charge_on_volt = SHARPSL_CHARGE_ON_VOLT, .charge_on_temp = SHARPSL_CHARGE_ON_TEMP, .charge_acin_high = SHARPSL_CHARGE_ON_ACIN_HIGH, diff --git a/arch/arm/mach-pxa/spitz_pm.c b/arch/arm/mach-pxa/spitz_pm.c index 23f050feb208..48396f4eb265 100644 --- a/arch/arm/mach-pxa/spitz_pm.c +++ b/arch/arm/mach-pxa/spitz_pm.c @@ -207,7 +207,9 @@ struct sharpsl_charger_machinfo spitz_pm_machinfo = { .read_devdata = spitzpm_read_devdata, .charger_wakeup = spitz_charger_wakeup, .should_wakeup = spitz_should_wakeup, +#ifdef CONFIG_BACKLIGHT_CORGI .backlight_limit = corgibl_limit_intensity, +#endif .charge_on_volt = SHARPSL_CHARGE_ON_VOLT, .charge_on_temp = SHARPSL_CHARGE_ON_TEMP, .charge_acin_high = SHARPSL_CHARGE_ON_ACIN_HIGH, -- cgit v1.2.3 From 284d115ec9b70d7c38752d10ad393a198db07a4b Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 17:32:16 +0100 Subject: [ARM] pxa: separate PXA25x and PXA27x UDC register definitions The PXA25x and PXA27x USB device controller register definitions are different. Currently, they live side by side in pxa-regs.h, but only one set is available depending on the setting of PXA25x or PXA27x. This means that if we build to support both PXA25x and PXA27x, the PXA27x definitions are unavailable, even to PXA27x specific code. Remove these definitions from pxa-regs.h, and place them in separate files. Include these files where appropriate. Note: according to the dependencies in drivers/usb/gadget/Kconfig, we do not support the UDC on PXA27x nor PXA3xx CPUs, so remove the platform devices from pxa27x.c and pxa3xx.c. Signed-off-by: Russell King --- arch/arm/mach-pxa/em-x270.c | 1 + arch/arm/mach-pxa/pxa27x.c | 2 +- arch/arm/mach-pxa/pxa3xx.c | 2 +- drivers/usb/gadget/pxa2xx_udc.c | 10 +- include/asm-arm/arch-pxa/pxa-regs.h | 412 ---------------------------------- include/asm-arm/arch-pxa/pxa25x-udc.h | 163 ++++++++++++++ include/asm-arm/arch-pxa/pxa27x-udc.h | 256 +++++++++++++++++++++ 7 files changed, 430 insertions(+), 416 deletions(-) create mode 100644 include/asm-arm/arch-pxa/pxa25x-udc.h create mode 100644 include/asm-arm/arch-pxa/pxa27x-udc.h diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index edc4f07a230d..1269ac991505 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -24,6 +24,7 @@ #include #include +#include #include #include #include diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c index 7e945836e129..cdaf573e0f17 100644 --- a/arch/arm/mach-pxa/pxa27x.c +++ b/arch/arm/mach-pxa/pxa27x.c @@ -353,7 +353,7 @@ void __init pxa_set_i2c_power_info(struct i2c_pxa_platform_data *info) } static struct platform_device *devices[] __initdata = { - &pxa_device_udc, +/* &pxa_device_udc, The UDC driver is PXA25x only */ &pxa_device_ffuart, &pxa_device_btuart, &pxa_device_stuart, diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c index 644550bfa330..7fbe78649dad 100644 --- a/arch/arm/mach-pxa/pxa3xx.c +++ b/arch/arm/mach-pxa/pxa3xx.c @@ -520,7 +520,7 @@ void __init pxa3xx_init_irq(void) */ static struct platform_device *devices[] __initdata = { - &pxa_device_udc, +/* &pxa_device_udc, The UDC driver is PXA25x only */ &pxa_device_ffuart, &pxa_device_btuart, &pxa_device_stuart, diff --git a/drivers/usb/gadget/pxa2xx_udc.c b/drivers/usb/gadget/pxa2xx_udc.c index 08f699b1fc57..63db96adc0b0 100644 --- a/drivers/usb/gadget/pxa2xx_udc.c +++ b/drivers/usb/gadget/pxa2xx_udc.c @@ -46,19 +46,25 @@ #include #include #include +#include #include #include #include -#include #include #include #include -#include #include #include +/* + * This driver is PXA25x only. Grab the right register definitions. + */ +#ifdef CONFIG_ARCH_PXA +#include +#endif + #include diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h index 4b2ea1e95c57..68d742877308 100644 --- a/include/asm-arm/arch-pxa/pxa-regs.h +++ b/include/asm-arm/arch-pxa/pxa-regs.h @@ -599,418 +599,6 @@ #define SMC_REG_BASE __REG(0x40500500) /* Secondary Modem Codec */ -/* - * USB Device Controller - * PXA25x and PXA27x USB device controller registers are different. - */ -#if defined(CONFIG_PXA25x) - -#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */ -#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */ -#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */ - -#define UDCCR __REG(0x40600000) /* UDC Control Register */ -#define UDCCR_UDE (1 << 0) /* UDC enable */ -#define UDCCR_UDA (1 << 1) /* UDC active */ -#define UDCCR_RSM (1 << 2) /* Device resume */ -#define UDCCR_RESIR (1 << 3) /* Resume interrupt request */ -#define UDCCR_SUSIR (1 << 4) /* Suspend interrupt request */ -#define UDCCR_SRM (1 << 5) /* Suspend/resume interrupt mask */ -#define UDCCR_RSTIR (1 << 6) /* Reset interrupt request */ -#define UDCCR_REM (1 << 7) /* Reset interrupt mask */ - -#define UDCCS0 __REG(0x40600010) /* UDC Endpoint 0 Control/Status Register */ -#define UDCCS0_OPR (1 << 0) /* OUT packet ready */ -#define UDCCS0_IPR (1 << 1) /* IN packet ready */ -#define UDCCS0_FTF (1 << 2) /* Flush Tx FIFO */ -#define UDCCS0_DRWF (1 << 3) /* Device remote wakeup feature */ -#define UDCCS0_SST (1 << 4) /* Sent stall */ -#define UDCCS0_FST (1 << 5) /* Force stall */ -#define UDCCS0_RNE (1 << 6) /* Receive FIFO no empty */ -#define UDCCS0_SA (1 << 7) /* Setup active */ - -/* Bulk IN - Endpoint 1,6,11 */ -#define UDCCS1 __REG(0x40600014) /* UDC Endpoint 1 (IN) Control/Status Register */ -#define UDCCS6 __REG(0x40600028) /* UDC Endpoint 6 (IN) Control/Status Register */ -#define UDCCS11 __REG(0x4060003C) /* UDC Endpoint 11 (IN) Control/Status Register */ - -#define UDCCS_BI_TFS (1 << 0) /* Transmit FIFO service */ -#define UDCCS_BI_TPC (1 << 1) /* Transmit packet complete */ -#define UDCCS_BI_FTF (1 << 2) /* Flush Tx FIFO */ -#define UDCCS_BI_TUR (1 << 3) /* Transmit FIFO underrun */ -#define UDCCS_BI_SST (1 << 4) /* Sent stall */ -#define UDCCS_BI_FST (1 << 5) /* Force stall */ -#define UDCCS_BI_TSP (1 << 7) /* Transmit short packet */ - -/* Bulk OUT - Endpoint 2,7,12 */ -#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */ -#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */ -#define UDCCS12 __REG(0x40600040) /* UDC Endpoint 12 (OUT) Control/Status Register */ - -#define UDCCS_BO_RFS (1 << 0) /* Receive FIFO service */ -#define UDCCS_BO_RPC (1 << 1) /* Receive packet complete */ -#define UDCCS_BO_DME (1 << 3) /* DMA enable */ -#define UDCCS_BO_SST (1 << 4) /* Sent stall */ -#define UDCCS_BO_FST (1 << 5) /* Force stall */ -#define UDCCS_BO_RNE (1 << 6) /* Receive FIFO not empty */ -#define UDCCS_BO_RSP (1 << 7) /* Receive short packet */ - -/* Isochronous IN - Endpoint 3,8,13 */ -#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */ -#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */ -#define UDCCS13 __REG(0x40600044) /* UDC Endpoint 13 (IN) Control/Status Register */ - -#define UDCCS_II_TFS (1 << 0) /* Transmit FIFO service */ -#define UDCCS_II_TPC (1 << 1) /* Transmit packet complete */ -#define UDCCS_II_FTF (1 << 2) /* Flush Tx FIFO */ -#define UDCCS_II_TUR (1 << 3) /* Transmit FIFO underrun */ -#define UDCCS_II_TSP (1 << 7) /* Transmit short packet */ - -/* Isochronous OUT - Endpoint 4,9,14 */ -#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */ -#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */ -#define UDCCS14 __REG(0x40600048) /* UDC Endpoint 14 (OUT) Control/Status Register */ - -#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */ -#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */ -#define UDCCS_IO_ROF (1 << 2) /* Receive overflow */ -#define UDCCS_IO_DME (1 << 3) /* DMA enable */ -#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */ -#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */ - -/* Interrupt IN - Endpoint 5,10,15 */ -#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */ -#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */ -#define UDCCS15 __REG(0x4060004C) /* UDC Endpoint 15 (Interrupt) Control/Status Register */ - -#define UDCCS_INT_TFS (1 << 0) /* Transmit FIFO service */ -#define UDCCS_INT_TPC (1 << 1) /* Transmit packet complete */ -#define UDCCS_INT_FTF (1 << 2) /* Flush Tx FIFO */ -#define UDCCS_INT_TUR (1 << 3) /* Transmit FIFO underrun */ -#define UDCCS_INT_SST (1 << 4) /* Sent stall */ -#define UDCCS_INT_FST (1 << 5) /* Force stall */ -#define UDCCS_INT_TSP (1 << 7) /* Transmit short packet */ - -#define UFNRH __REG(0x40600060) /* UDC Frame Number Register High */ -#define UFNRL __REG(0x40600064) /* UDC Frame Number Register Low */ -#define UBCR2 __REG(0x40600068) /* UDC Byte Count Reg 2 */ -#define UBCR4 __REG(0x4060006c) /* UDC Byte Count Reg 4 */ -#define UBCR7 __REG(0x40600070) /* UDC Byte Count Reg 7 */ -#define UBCR9 __REG(0x40600074) /* UDC Byte Count Reg 9 */ -#define UBCR12 __REG(0x40600078) /* UDC Byte Count Reg 12 */ -#define UBCR14 __REG(0x4060007c) /* UDC Byte Count Reg 14 */ -#define UDDR0 __REG(0x40600080) /* UDC Endpoint 0 Data Register */ -#define UDDR1 __REG(0x40600100) /* UDC Endpoint 1 Data Register */ -#define UDDR2 __REG(0x40600180) /* UDC Endpoint 2 Data Register */ -#define UDDR3 __REG(0x40600200) /* UDC Endpoint 3 Data Register */ -#define UDDR4 __REG(0x40600400) /* UDC Endpoint 4 Data Register */ -#define UDDR5 __REG(0x406000A0) /* UDC Endpoint 5 Data Register */ -#define UDDR6 __REG(0x40600600) /* UDC Endpoint 6 Data Register */ -#define UDDR7 __REG(0x40600680) /* UDC Endpoint 7 Data Register */ -#define UDDR8 __REG(0x40600700) /* UDC Endpoint 8 Data Register */ -#define UDDR9 __REG(0x40600900) /* UDC Endpoint 9 Data Register */ -#define UDDR10 __REG(0x406000C0) /* UDC Endpoint 10 Data Register */ -#define UDDR11 __REG(0x40600B00) /* UDC Endpoint 11 Data Register */ -#define UDDR12 __REG(0x40600B80) /* UDC Endpoint 12 Data Register */ -#define UDDR13 __REG(0x40600C00) /* UDC Endpoint 13 Data Register */ -#define UDDR14 __REG(0x40600E00) /* UDC Endpoint 14 Data Register */ -#define UDDR15 __REG(0x406000E0) /* UDC Endpoint 15 Data Register */ - -#define UICR0 __REG(0x40600050) /* UDC Interrupt Control Register 0 */ - -#define UICR0_IM0 (1 << 0) /* Interrupt mask ep 0 */ -#define UICR0_IM1 (1 << 1) /* Interrupt mask ep 1 */ -#define UICR0_IM2 (1 << 2) /* Interrupt mask ep 2 */ -#define UICR0_IM3 (1 << 3) /* Interrupt mask ep 3 */ -#define UICR0_IM4 (1 << 4) /* Interrupt mask ep 4 */ -#define UICR0_IM5 (1 << 5) /* Interrupt mask ep 5 */ -#define UICR0_IM6 (1 << 6) /* Interrupt mask ep 6 */ -#define UICR0_IM7 (1 << 7) /* Interrupt mask ep 7 */ - -#define UICR1 __REG(0x40600054) /* UDC Interrupt Control Register 1 */ - -#define UICR1_IM8 (1 << 0) /* Interrupt mask ep 8 */ -#define UICR1_IM9 (1 << 1) /* Interrupt mask ep 9 */ -#define UICR1_IM10 (1 << 2) /* Interrupt mask ep 10 */ -#define UICR1_IM11 (1 << 3) /* Interrupt mask ep 11 */ -#define UICR1_IM12 (1 << 4) /* Interrupt mask ep 12 */ -#define UICR1_IM13 (1 << 5) /* Interrupt mask ep 13 */ -#define UICR1_IM14 (1 << 6) /* Interrupt mask ep 14 */ -#define UICR1_IM15 (1 << 7) /* Interrupt mask ep 15 */ - -#define USIR0 __REG(0x40600058) /* UDC Status Interrupt Register 0 */ - -#define USIR0_IR0 (1 << 0) /* Interrupt request ep 0 */ -#define USIR0_IR1 (1 << 1) /* Interrupt request ep 1 */ -#define USIR0_IR2 (1 << 2) /* Interrupt request ep 2 */ -#define USIR0_IR3 (1 << 3) /* Interrupt request ep 3 */ -#define USIR0_IR4 (1 << 4) /* Interrupt request ep 4 */ -#define USIR0_IR5 (1 << 5) /* Interrupt request ep 5 */ -#define USIR0_IR6 (1 << 6) /* Interrupt request ep 6 */ -#define USIR0_IR7 (1 << 7) /* Interrupt request ep 7 */ - -#define USIR1 __REG(0x4060005C) /* UDC Status Interrupt Register 1 */ - -#define USIR1_IR8 (1 << 0) /* Interrupt request ep 8 */ -#define USIR1_IR9 (1 << 1) /* Interrupt request ep 9 */ -#define USIR1_IR10 (1 << 2) /* Interrupt request ep 10 */ -#define USIR1_IR11 (1 << 3) /* Interrupt request ep 11 */ -#define USIR1_IR12 (1 << 4) /* Interrupt request ep 12 */ -#define USIR1_IR13 (1 << 5) /* Interrupt request ep 13 */ -#define USIR1_IR14 (1 << 6) /* Interrupt request ep 14 */ -#define USIR1_IR15 (1 << 7) /* Interrupt request ep 15 */ - -#elif defined(CONFIG_PXA27x) - -#define UDCCR __REG(0x40600000) /* UDC Control Register */ -#define UDCCR_OEN (1 << 31) /* On-the-Go Enable */ -#define UDCCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation - Protocol Port Support */ -#define UDCCR_AHNP (1 << 29) /* A-device Host Negotiation Protocol - Support */ -#define UDCCR_BHNP (1 << 28) /* B-device Host Negotiation Protocol - Enable */ -#define UDCCR_DWRE (1 << 16) /* Device Remote Wake-up Enable */ -#define UDCCR_ACN (0x03 << 11) /* Active UDC configuration Number */ -#define UDCCR_ACN_S 11 -#define UDCCR_AIN (0x07 << 8) /* Active UDC interface Number */ -#define UDCCR_AIN_S 8 -#define UDCCR_AAISN (0x07 << 5) /* Active UDC Alternate Interface - Setting Number */ -#define UDCCR_AAISN_S 5 -#define UDCCR_SMAC (1 << 4) /* Switch Endpoint Memory to Active - Configuration */ -#define UDCCR_EMCE (1 << 3) /* Endpoint Memory Configuration - Error */ -#define UDCCR_UDR (1 << 2) /* UDC Resume */ -#define UDCCR_UDA (1 << 1) /* UDC Active */ -#define UDCCR_UDE (1 << 0) /* UDC Enable */ - -#define UDCICR0 __REG(0x40600004) /* UDC Interrupt Control Register0 */ -#define UDCICR1 __REG(0x40600008) /* UDC Interrupt Control Register1 */ -#define UDCICR_FIFOERR (1 << 1) /* FIFO Error interrupt for EP */ -#define UDCICR_PKTCOMPL (1 << 0) /* Packet Complete interrupt for EP */ - -#define UDC_INT_FIFOERROR (0x2) -#define UDC_INT_PACKETCMP (0x1) - -#define UDCICR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2)) -#define UDCICR1_IECC (1 << 31) /* IntEn - Configuration Change */ -#define UDCICR1_IESOF (1 << 30) /* IntEn - Start of Frame */ -#define UDCICR1_IERU (1 << 29) /* IntEn - Resume */ -#define UDCICR1_IESU (1 << 28) /* IntEn - Suspend */ -#define UDCICR1_IERS (1 << 27) /* IntEn - Reset */ - -#define UDCISR0 __REG(0x4060000C) /* UDC Interrupt Status Register 0 */ -#define UDCISR1 __REG(0x40600010) /* UDC Interrupt Status Register 1 */ -#define UDCISR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2)) -#define UDCISR1_IRCC (1 << 31) /* IntReq - Configuration Change */ -#define UDCISR1_IRSOF (1 << 30) /* IntReq - Start of Frame */ -#define UDCISR1_IRRU (1 << 29) /* IntReq - Resume */ -#define UDCISR1_IRSU (1 << 28) /* IntReq - Suspend */ -#define UDCISR1_IRRS (1 << 27) /* IntReq - Reset */ - -#define UDCFNR __REG(0x40600014) /* UDC Frame Number Register */ -#define UDCOTGICR __REG(0x40600018) /* UDC On-The-Go interrupt control */ -#define UDCOTGICR_IESF (1 << 24) /* OTG SET_FEATURE command recvd */ -#define UDCOTGICR_IEXR (1 << 17) /* Extra Transciever Interrupt - Rising Edge Interrupt Enable */ -#define UDCOTGICR_IEXF (1 << 16) /* Extra Transciever Interrupt - Falling Edge Interrupt Enable */ -#define UDCOTGICR_IEVV40R (1 << 9) /* OTG Vbus Valid 4.0V Rising Edge - Interrupt Enable */ -#define UDCOTGICR_IEVV40F (1 << 8) /* OTG Vbus Valid 4.0V Falling Edge - Interrupt Enable */ -#define UDCOTGICR_IEVV44R (1 << 7) /* OTG Vbus Valid 4.4V Rising Edge - Interrupt Enable */ -#define UDCOTGICR_IEVV44F (1 << 6) /* OTG Vbus Valid 4.4V Falling Edge - Interrupt Enable */ -#define UDCOTGICR_IESVR (1 << 5) /* OTG Session Valid Rising Edge - Interrupt Enable */ -#define UDCOTGICR_IESVF (1 << 4) /* OTG Session Valid Falling Edge - Interrupt Enable */ -#define UDCOTGICR_IESDR (1 << 3) /* OTG A-Device SRP Detect Rising - Edge Interrupt Enable */ -#define UDCOTGICR_IESDF (1 << 2) /* OTG A-Device SRP Detect Falling - Edge Interrupt Enable */ -#define UDCOTGICR_IEIDR (1 << 1) /* OTG ID Change Rising Edge - Interrupt Enable */ -#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge - Interrupt Enable */ - -#define UP2OCR __REG(0x40600020) /* USB Port 2 Output Control register */ - -#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */ -#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */ -#define UP2OCR_DPPDE (1 << 2) /* Host Port 2 Transceiver D+ Pull Down Enable */ -#define UP2OCR_DMPDE (1 << 3) /* Host Port 2 Transceiver D- Pull Down Enable */ -#define UP2OCR_DPPUE (1 << 4) /* Host Port 2 Transceiver D+ Pull Up Enable */ -#define UP2OCR_DMPUE (1 << 5) /* Host Port 2 Transceiver D- Pull Up Enable */ -#define UP2OCR_DPPUBE (1 << 6) /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */ -#define UP2OCR_DMPUBE (1 << 7) /* Host Port 2 Transceiver D- Pull Up Bypass Enable */ -#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */ -#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */ -#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */ -#define UP2OCR_HXS (1 << 16) /* Host Port 2 Transceiver Output Select */ -#define UP2OCR_HXOE (1 << 17) /* Host Port 2 Transceiver Output Enable */ -#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */ - -#define UDCCSN(x) __REG2(0x40600100, (x) << 2) -#define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */ -#define UDCCSR0_SA (1 << 7) /* Setup Active */ -#define UDCCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */ -#define UDCCSR0_FST (1 << 5) /* Force Stall */ -#define UDCCSR0_SST (1 << 4) /* Sent Stall */ -#define UDCCSR0_DME (1 << 3) /* DMA Enable */ -#define UDCCSR0_FTF (1 << 2) /* Flush Transmit FIFO */ -#define UDCCSR0_IPR (1 << 1) /* IN Packet Ready */ -#define UDCCSR0_OPC (1 << 0) /* OUT Packet Complete */ - -#define UDCCSRA __REG(0x40600104) /* UDC Control/Status register - Endpoint A */ -#define UDCCSRB __REG(0x40600108) /* UDC Control/Status register - Endpoint B */ -#define UDCCSRC __REG(0x4060010C) /* UDC Control/Status register - Endpoint C */ -#define UDCCSRD __REG(0x40600110) /* UDC Control/Status register - Endpoint D */ -#define UDCCSRE __REG(0x40600114) /* UDC Control/Status register - Endpoint E */ -#define UDCCSRF __REG(0x40600118) /* UDC Control/Status register - Endpoint F */ -#define UDCCSRG __REG(0x4060011C) /* UDC Control/Status register - Endpoint G */ -#define UDCCSRH __REG(0x40600120) /* UDC Control/Status register - Endpoint H */ -#define UDCCSRI __REG(0x40600124) /* UDC Control/Status register - Endpoint I */ -#define UDCCSRJ __REG(0x40600128) /* UDC Control/Status register - Endpoint J */ -#define UDCCSRK __REG(0x4060012C) /* UDC Control/Status register - Endpoint K */ -#define UDCCSRL __REG(0x40600130) /* UDC Control/Status register - Endpoint L */ -#define UDCCSRM __REG(0x40600134) /* UDC Control/Status register - Endpoint M */ -#define UDCCSRN __REG(0x40600138) /* UDC Control/Status register - Endpoint N */ -#define UDCCSRP __REG(0x4060013C) /* UDC Control/Status register - Endpoint P */ -#define UDCCSRQ __REG(0x40600140) /* UDC Control/Status register - Endpoint Q */ -#define UDCCSRR __REG(0x40600144) /* UDC Control/Status register - Endpoint R */ -#define UDCCSRS __REG(0x40600148) /* UDC Control/Status register - Endpoint S */ -#define UDCCSRT __REG(0x4060014C) /* UDC Control/Status register - Endpoint T */ -#define UDCCSRU __REG(0x40600150) /* UDC Control/Status register - Endpoint U */ -#define UDCCSRV __REG(0x40600154) /* UDC Control/Status register - Endpoint V */ -#define UDCCSRW __REG(0x40600158) /* UDC Control/Status register - Endpoint W */ -#define UDCCSRX __REG(0x4060015C) /* UDC Control/Status register - Endpoint X */ - -#define UDCCSR_DPE (1 << 9) /* Data Packet Error */ -#define UDCCSR_FEF (1 << 8) /* Flush Endpoint FIFO */ -#define UDCCSR_SP (1 << 7) /* Short Packet Control/Status */ -#define UDCCSR_BNE (1 << 6) /* Buffer Not Empty (IN endpoints) */ -#define UDCCSR_BNF (1 << 6) /* Buffer Not Full (OUT endpoints) */ -#define UDCCSR_FST (1 << 5) /* Force STALL */ -#define UDCCSR_SST (1 << 4) /* Sent STALL */ -#define UDCCSR_DME (1 << 3) /* DMA Enable */ -#define UDCCSR_TRN (1 << 2) /* Tx/Rx NAK */ -#define UDCCSR_PC (1 << 1) /* Packet Complete */ -#define UDCCSR_FS (1 << 0) /* FIFO needs service */ - -#define UDCBCN(x) __REG2(0x40600200, (x)<<2) -#define UDCBCR0 __REG(0x40600200) /* Byte Count Register - EP0 */ -#define UDCBCRA __REG(0x40600204) /* Byte Count Register - EPA */ -#define UDCBCRB __REG(0x40600208) /* Byte Count Register - EPB */ -#define UDCBCRC __REG(0x4060020C) /* Byte Count Register - EPC */ -#define UDCBCRD __REG(0x40600210) /* Byte Count Register - EPD */ -#define UDCBCRE __REG(0x40600214) /* Byte Count Register - EPE */ -#define UDCBCRF __REG(0x40600218) /* Byte Count Register - EPF */ -#define UDCBCRG __REG(0x4060021C) /* Byte Count Register - EPG */ -#define UDCBCRH __REG(0x40600220) /* Byte Count Register - EPH */ -#define UDCBCRI __REG(0x40600224) /* Byte Count Register - EPI */ -#define UDCBCRJ __REG(0x40600228) /* Byte Count Register - EPJ */ -#define UDCBCRK __REG(0x4060022C) /* Byte Count Register - EPK */ -#define UDCBCRL __REG(0x40600230) /* Byte Count Register - EPL */ -#define UDCBCRM __REG(0x40600234) /* Byte Count Register - EPM */ -#define UDCBCRN __REG(0x40600238) /* Byte Count Register - EPN */ -#define UDCBCRP __REG(0x4060023C) /* Byte Count Register - EPP */ -#define UDCBCRQ __REG(0x40600240) /* Byte Count Register - EPQ */ -#define UDCBCRR __REG(0x40600244) /* Byte Count Register - EPR */ -#define UDCBCRS __REG(0x40600248) /* Byte Count Register - EPS */ -#define UDCBCRT __REG(0x4060024C) /* Byte Count Register - EPT */ -#define UDCBCRU __REG(0x40600250) /* Byte Count Register - EPU */ -#define UDCBCRV __REG(0x40600254) /* Byte Count Register - EPV */ -#define UDCBCRW __REG(0x40600258) /* Byte Count Register - EPW */ -#define UDCBCRX __REG(0x4060025C) /* Byte Count Register - EPX */ - -#define UDCDN(x) __REG2(0x40600300, (x)<<2) -#define PHYS_UDCDN(x) (0x40600300 + ((x)<<2)) -#define PUDCDN(x) (volatile u32 *)(io_p2v(PHYS_UDCDN((x)))) -#define UDCDR0 __REG(0x40600300) /* Data Register - EP0 */ -#define UDCDRA __REG(0x40600304) /* Data Register - EPA */ -#define UDCDRB __REG(0x40600308) /* Data Register - EPB */ -#define UDCDRC __REG(0x4060030C) /* Data Register - EPC */ -#define UDCDRD __REG(0x40600310) /* Data Register - EPD */ -#define UDCDRE __REG(0x40600314) /* Data Register - EPE */ -#define UDCDRF __REG(0x40600318) /* Data Register - EPF */ -#define UDCDRG __REG(0x4060031C) /* Data Register - EPG */ -#define UDCDRH __REG(0x40600320) /* Data Register - EPH */ -#define UDCDRI __REG(0x40600324) /* Data Register - EPI */ -#define UDCDRJ __REG(0x40600328) /* Data Register - EPJ */ -#define UDCDRK __REG(0x4060032C) /* Data Register - EPK */ -#define UDCDRL __REG(0x40600330) /* Data Register - EPL */ -#define UDCDRM __REG(0x40600334) /* Data Register - EPM */ -#define UDCDRN __REG(0x40600338) /* Data Register - EPN */ -#define UDCDRP __REG(0x4060033C) /* Data Register - EPP */ -#define UDCDRQ __REG(0x40600340) /* Data Register - EPQ */ -#define UDCDRR __REG(0x40600344) /* Data Register - EPR */ -#define UDCDRS __REG(0x40600348) /* Data Register - EPS */ -#define UDCDRT __REG(0x4060034C) /* Data Register - EPT */ -#define UDCDRU __REG(0x40600350) /* Data Register - EPU */ -#define UDCDRV __REG(0x40600354) /* Data Register - EPV */ -#define UDCDRW __REG(0x40600358) /* Data Register - EPW */ -#define UDCDRX __REG(0x4060035C) /* Data Register - EPX */ - -#define UDCCN(x) __REG2(0x40600400, (x)<<2) -#define UDCCRA __REG(0x40600404) /* Configuration register EPA */ -#define UDCCRB __REG(0x40600408) /* Configuration register EPB */ -#define UDCCRC __REG(0x4060040C) /* Configuration register EPC */ -#define UDCCRD __REG(0x40600410) /* Configuration register EPD */ -#define UDCCRE __REG(0x40600414) /* Configuration register EPE */ -#define UDCCRF __REG(0x40600418) /* Configuration register EPF */ -#define UDCCRG __REG(0x4060041C) /* Configuration register EPG */ -#define UDCCRH __REG(0x40600420) /* Configuration register EPH */ -#define UDCCRI __REG(0x40600424) /* Configuration register EPI */ -#define UDCCRJ __REG(0x40600428) /* Configuration register EPJ */ -#define UDCCRK __REG(0x4060042C) /* Configuration register EPK */ -#define UDCCRL __REG(0x40600430) /* Configuration register EPL */ -#define UDCCRM __REG(0x40600434) /* Configuration register EPM */ -#define UDCCRN __REG(0x40600438) /* Configuration register EPN */ -#define UDCCRP __REG(0x4060043C) /* Configuration register EPP */ -#define UDCCRQ __REG(0x40600440) /* Configuration register EPQ */ -#define UDCCRR __REG(0x40600444) /* Configuration register EPR */ -#define UDCCRS __REG(0x40600448) /* Configuration register EPS */ -#define UDCCRT __REG(0x4060044C) /* Configuration register EPT */ -#define UDCCRU __REG(0x40600450) /* Configuration register EPU */ -#define UDCCRV __REG(0x40600454) /* Configuration register EPV */ -#define UDCCRW __REG(0x40600458) /* Configuration register EPW */ -#define UDCCRX __REG(0x4060045C) /* Configuration register EPX */ - -#define UDCCONR_CN (0x03 << 25) /* Configuration Number */ -#define UDCCONR_CN_S (25) -#define UDCCONR_IN (0x07 << 22) /* Interface Number */ -#define UDCCONR_IN_S (22) -#define UDCCONR_AISN (0x07 << 19) /* Alternate Interface Number */ -#define UDCCONR_AISN_S (19) -#define UDCCONR_EN (0x0f << 15) /* Endpoint Number */ -#define UDCCONR_EN_S (15) -#define UDCCONR_ET (0x03 << 13) /* Endpoint Type: */ -#define UDCCONR_ET_S (13) -#define UDCCONR_ET_INT (0x03 << 13) /* Interrupt */ -#define UDCCONR_ET_BULK (0x02 << 13) /* Bulk */ -#define UDCCONR_ET_ISO (0x01 << 13) /* Isochronous */ -#define UDCCONR_ET_NU (0x00 << 13) /* Not used */ -#define UDCCONR_ED (1 << 12) /* Endpoint Direction */ -#define UDCCONR_MPS (0x3ff << 2) /* Maximum Packet Size */ -#define UDCCONR_MPS_S (2) -#define UDCCONR_DE (1 << 1) /* Double Buffering Enable */ -#define UDCCONR_EE (1 << 0) /* Endpoint Enable */ - - -#define UDC_INT_FIFOERROR (0x2) -#define UDC_INT_PACKETCMP (0x1) - -#define UDC_FNR_MASK (0x7ff) - -#define UDCCSR_WR_MASK (UDCCSR_DME|UDCCSR_FST) -#define UDC_BCR_MASK (0x3ff) -#endif - /* * Fast Infrared Communication Port */ diff --git a/include/asm-arm/arch-pxa/pxa25x-udc.h b/include/asm-arm/arch-pxa/pxa25x-udc.h new file mode 100644 index 000000000000..840305916b6d --- /dev/null +++ b/include/asm-arm/arch-pxa/pxa25x-udc.h @@ -0,0 +1,163 @@ +#ifndef _ASM_ARCH_PXA25X_UDC_H +#define _ASM_ARCH_PXA25X_UDC_H + +#ifdef _ASM_ARCH_PXA27X_UDC_H +#error You can't include both PXA25x and PXA27x UDC support +#endif + +#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */ +#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */ +#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */ + +#define UDCCR __REG(0x40600000) /* UDC Control Register */ +#define UDCCR_UDE (1 << 0) /* UDC enable */ +#define UDCCR_UDA (1 << 1) /* UDC active */ +#define UDCCR_RSM (1 << 2) /* Device resume */ +#define UDCCR_RESIR (1 << 3) /* Resume interrupt request */ +#define UDCCR_SUSIR (1 << 4) /* Suspend interrupt request */ +#define UDCCR_SRM (1 << 5) /* Suspend/resume interrupt mask */ +#define UDCCR_RSTIR (1 << 6) /* Reset interrupt request */ +#define UDCCR_REM (1 << 7) /* Reset interrupt mask */ + +#define UDCCS0 __REG(0x40600010) /* UDC Endpoint 0 Control/Status Register */ +#define UDCCS0_OPR (1 << 0) /* OUT packet ready */ +#define UDCCS0_IPR (1 << 1) /* IN packet ready */ +#define UDCCS0_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS0_DRWF (1 << 3) /* Device remote wakeup feature */ +#define UDCCS0_SST (1 << 4) /* Sent stall */ +#define UDCCS0_FST (1 << 5) /* Force stall */ +#define UDCCS0_RNE (1 << 6) /* Receive FIFO no empty */ +#define UDCCS0_SA (1 << 7) /* Setup active */ + +/* Bulk IN - Endpoint 1,6,11 */ +#define UDCCS1 __REG(0x40600014) /* UDC Endpoint 1 (IN) Control/Status Register */ +#define UDCCS6 __REG(0x40600028) /* UDC Endpoint 6 (IN) Control/Status Register */ +#define UDCCS11 __REG(0x4060003C) /* UDC Endpoint 11 (IN) Control/Status Register */ + +#define UDCCS_BI_TFS (1 << 0) /* Transmit FIFO service */ +#define UDCCS_BI_TPC (1 << 1) /* Transmit packet complete */ +#define UDCCS_BI_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS_BI_TUR (1 << 3) /* Transmit FIFO underrun */ +#define UDCCS_BI_SST (1 << 4) /* Sent stall */ +#define UDCCS_BI_FST (1 << 5) /* Force stall */ +#define UDCCS_BI_TSP (1 << 7) /* Transmit short packet */ + +/* Bulk OUT - Endpoint 2,7,12 */ +#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */ +#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */ +#define UDCCS12 __REG(0x40600040) /* UDC Endpoint 12 (OUT) Control/Status Register */ + +#define UDCCS_BO_RFS (1 << 0) /* Receive FIFO service */ +#define UDCCS_BO_RPC (1 << 1) /* Receive packet complete */ +#define UDCCS_BO_DME (1 << 3) /* DMA enable */ +#define UDCCS_BO_SST (1 << 4) /* Sent stall */ +#define UDCCS_BO_FST (1 << 5) /* Force stall */ +#define UDCCS_BO_RNE (1 << 6) /* Receive FIFO not empty */ +#define UDCCS_BO_RSP (1 << 7) /* Receive short packet */ + +/* Isochronous IN - Endpoint 3,8,13 */ +#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */ +#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */ +#define UDCCS13 __REG(0x40600044) /* UDC Endpoint 13 (IN) Control/Status Register */ + +#define UDCCS_II_TFS (1 << 0) /* Transmit FIFO service */ +#define UDCCS_II_TPC (1 << 1) /* Transmit packet complete */ +#define UDCCS_II_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS_II_TUR (1 << 3) /* Transmit FIFO underrun */ +#define UDCCS_II_TSP (1 << 7) /* Transmit short packet */ + +/* Isochronous OUT - Endpoint 4,9,14 */ +#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */ +#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */ +#define UDCCS14 __REG(0x40600048) /* UDC Endpoint 14 (OUT) Control/Status Register */ + +#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */ +#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */ +#define UDCCS_IO_ROF (1 << 2) /* Receive overflow */ +#define UDCCS_IO_DME (1 << 3) /* DMA enable */ +#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */ +#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */ + +/* Interrupt IN - Endpoint 5,10,15 */ +#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */ +#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */ +#define UDCCS15 __REG(0x4060004C) /* UDC Endpoint 15 (Interrupt) Control/Status Register */ + +#define UDCCS_INT_TFS (1 << 0) /* Transmit FIFO service */ +#define UDCCS_INT_TPC (1 << 1) /* Transmit packet complete */ +#define UDCCS_INT_FTF (1 << 2) /* Flush Tx FIFO */ +#define UDCCS_INT_TUR (1 << 3) /* Transmit FIFO underrun */ +#define UDCCS_INT_SST (1 << 4) /* Sent stall */ +#define UDCCS_INT_FST (1 << 5) /* Force stall */ +#define UDCCS_INT_TSP (1 << 7) /* Transmit short packet */ + +#define UFNRH __REG(0x40600060) /* UDC Frame Number Register High */ +#define UFNRL __REG(0x40600064) /* UDC Frame Number Register Low */ +#define UBCR2 __REG(0x40600068) /* UDC Byte Count Reg 2 */ +#define UBCR4 __REG(0x4060006c) /* UDC Byte Count Reg 4 */ +#define UBCR7 __REG(0x40600070) /* UDC Byte Count Reg 7 */ +#define UBCR9 __REG(0x40600074) /* UDC Byte Count Reg 9 */ +#define UBCR12 __REG(0x40600078) /* UDC Byte Count Reg 12 */ +#define UBCR14 __REG(0x4060007c) /* UDC Byte Count Reg 14 */ +#define UDDR0 __REG(0x40600080) /* UDC Endpoint 0 Data Register */ +#define UDDR1 __REG(0x40600100) /* UDC Endpoint 1 Data Register */ +#define UDDR2 __REG(0x40600180) /* UDC Endpoint 2 Data Register */ +#define UDDR3 __REG(0x40600200) /* UDC Endpoint 3 Data Register */ +#define UDDR4 __REG(0x40600400) /* UDC Endpoint 4 Data Register */ +#define UDDR5 __REG(0x406000A0) /* UDC Endpoint 5 Data Register */ +#define UDDR6 __REG(0x40600600) /* UDC Endpoint 6 Data Register */ +#define UDDR7 __REG(0x40600680) /* UDC Endpoint 7 Data Register */ +#define UDDR8 __REG(0x40600700) /* UDC Endpoint 8 Data Register */ +#define UDDR9 __REG(0x40600900) /* UDC Endpoint 9 Data Register */ +#define UDDR10 __REG(0x406000C0) /* UDC Endpoint 10 Data Register */ +#define UDDR11 __REG(0x40600B00) /* UDC Endpoint 11 Data Register */ +#define UDDR12 __REG(0x40600B80) /* UDC Endpoint 12 Data Register */ +#define UDDR13 __REG(0x40600C00) /* UDC Endpoint 13 Data Register */ +#define UDDR14 __REG(0x40600E00) /* UDC Endpoint 14 Data Register */ +#define UDDR15 __REG(0x406000E0) /* UDC Endpoint 15 Data Register */ + +#define UICR0 __REG(0x40600050) /* UDC Interrupt Control Register 0 */ + +#define UICR0_IM0 (1 << 0) /* Interrupt mask ep 0 */ +#define UICR0_IM1 (1 << 1) /* Interrupt mask ep 1 */ +#define UICR0_IM2 (1 << 2) /* Interrupt mask ep 2 */ +#define UICR0_IM3 (1 << 3) /* Interrupt mask ep 3 */ +#define UICR0_IM4 (1 << 4) /* Interrupt mask ep 4 */ +#define UICR0_IM5 (1 << 5) /* Interrupt mask ep 5 */ +#define UICR0_IM6 (1 << 6) /* Interrupt mask ep 6 */ +#define UICR0_IM7 (1 << 7) /* Interrupt mask ep 7 */ + +#define UICR1 __REG(0x40600054) /* UDC Interrupt Control Register 1 */ + +#define UICR1_IM8 (1 << 0) /* Interrupt mask ep 8 */ +#define UICR1_IM9 (1 << 1) /* Interrupt mask ep 9 */ +#define UICR1_IM10 (1 << 2) /* Interrupt mask ep 10 */ +#define UICR1_IM11 (1 << 3) /* Interrupt mask ep 11 */ +#define UICR1_IM12 (1 << 4) /* Interrupt mask ep 12 */ +#define UICR1_IM13 (1 << 5) /* Interrupt mask ep 13 */ +#define UICR1_IM14 (1 << 6) /* Interrupt mask ep 14 */ +#define UICR1_IM15 (1 << 7) /* Interrupt mask ep 15 */ + +#define USIR0 __REG(0x40600058) /* UDC Status Interrupt Register 0 */ + +#define USIR0_IR0 (1 << 0) /* Interrupt request ep 0 */ +#define USIR0_IR1 (1 << 1) /* Interrupt request ep 1 */ +#define USIR0_IR2 (1 << 2) /* Interrupt request ep 2 */ +#define USIR0_IR3 (1 << 3) /* Interrupt request ep 3 */ +#define USIR0_IR4 (1 << 4) /* Interrupt request ep 4 */ +#define USIR0_IR5 (1 << 5) /* Interrupt request ep 5 */ +#define USIR0_IR6 (1 << 6) /* Interrupt request ep 6 */ +#define USIR0_IR7 (1 << 7) /* Interrupt request ep 7 */ + +#define USIR1 __REG(0x4060005C) /* UDC Status Interrupt Register 1 */ + +#define USIR1_IR8 (1 << 0) /* Interrupt request ep 8 */ +#define USIR1_IR9 (1 << 1) /* Interrupt request ep 9 */ +#define USIR1_IR10 (1 << 2) /* Interrupt request ep 10 */ +#define USIR1_IR11 (1 << 3) /* Interrupt request ep 11 */ +#define USIR1_IR12 (1 << 4) /* Interrupt request ep 12 */ +#define USIR1_IR13 (1 << 5) /* Interrupt request ep 13 */ +#define USIR1_IR14 (1 << 6) /* Interrupt request ep 14 */ +#define USIR1_IR15 (1 << 7) /* Interrupt request ep 15 */ + +#endif diff --git a/include/asm-arm/arch-pxa/pxa27x-udc.h b/include/asm-arm/arch-pxa/pxa27x-udc.h new file mode 100644 index 000000000000..9cf0b1f88112 --- /dev/null +++ b/include/asm-arm/arch-pxa/pxa27x-udc.h @@ -0,0 +1,256 @@ +#ifndef _ASM_ARCH_PXA27X_UDC_H +#define _ASM_ARCH_PXA27X_UDC_H + +#ifdef _ASM_ARCH_PXA25X_UDC_H +#error You can't include both PXA25x and PXA27x UDC support +#endif + +#define UDCCR __REG(0x40600000) /* UDC Control Register */ +#define UDCCR_OEN (1 << 31) /* On-the-Go Enable */ +#define UDCCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation + Protocol Port Support */ +#define UDCCR_AHNP (1 << 29) /* A-device Host Negotiation Protocol + Support */ +#define UDCCR_BHNP (1 << 28) /* B-device Host Negotiation Protocol + Enable */ +#define UDCCR_DWRE (1 << 16) /* Device Remote Wake-up Enable */ +#define UDCCR_ACN (0x03 << 11) /* Active UDC configuration Number */ +#define UDCCR_ACN_S 11 +#define UDCCR_AIN (0x07 << 8) /* Active UDC interface Number */ +#define UDCCR_AIN_S 8 +#define UDCCR_AAISN (0x07 << 5) /* Active UDC Alternate Interface + Setting Number */ +#define UDCCR_AAISN_S 5 +#define UDCCR_SMAC (1 << 4) /* Switch Endpoint Memory to Active + Configuration */ +#define UDCCR_EMCE (1 << 3) /* Endpoint Memory Configuration + Error */ +#define UDCCR_UDR (1 << 2) /* UDC Resume */ +#define UDCCR_UDA (1 << 1) /* UDC Active */ +#define UDCCR_UDE (1 << 0) /* UDC Enable */ + +#define UDCICR0 __REG(0x40600004) /* UDC Interrupt Control Register0 */ +#define UDCICR1 __REG(0x40600008) /* UDC Interrupt Control Register1 */ +#define UDCICR_FIFOERR (1 << 1) /* FIFO Error interrupt for EP */ +#define UDCICR_PKTCOMPL (1 << 0) /* Packet Complete interrupt for EP */ + +#define UDC_INT_FIFOERROR (0x2) +#define UDC_INT_PACKETCMP (0x1) + +#define UDCICR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2)) +#define UDCICR1_IECC (1 << 31) /* IntEn - Configuration Change */ +#define UDCICR1_IESOF (1 << 30) /* IntEn - Start of Frame */ +#define UDCICR1_IERU (1 << 29) /* IntEn - Resume */ +#define UDCICR1_IESU (1 << 28) /* IntEn - Suspend */ +#define UDCICR1_IERS (1 << 27) /* IntEn - Reset */ + +#define UDCISR0 __REG(0x4060000C) /* UDC Interrupt Status Register 0 */ +#define UDCISR1 __REG(0x40600010) /* UDC Interrupt Status Register 1 */ +#define UDCISR_INT(n,intr) (((intr) & 0x03) << (((n) & 0x0F) * 2)) +#define UDCISR1_IRCC (1 << 31) /* IntReq - Configuration Change */ +#define UDCISR1_IRSOF (1 << 30) /* IntReq - Start of Frame */ +#define UDCISR1_IRRU (1 << 29) /* IntReq - Resume */ +#define UDCISR1_IRSU (1 << 28) /* IntReq - Suspend */ +#define UDCISR1_IRRS (1 << 27) /* IntReq - Reset */ + +#define UDCFNR __REG(0x40600014) /* UDC Frame Number Register */ +#define UDCOTGICR __REG(0x40600018) /* UDC On-The-Go interrupt control */ +#define UDCOTGICR_IESF (1 << 24) /* OTG SET_FEATURE command recvd */ +#define UDCOTGICR_IEXR (1 << 17) /* Extra Transciever Interrupt + Rising Edge Interrupt Enable */ +#define UDCOTGICR_IEXF (1 << 16) /* Extra Transciever Interrupt + Falling Edge Interrupt Enable */ +#define UDCOTGICR_IEVV40R (1 << 9) /* OTG Vbus Valid 4.0V Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IEVV40F (1 << 8) /* OTG Vbus Valid 4.0V Falling Edge + Interrupt Enable */ +#define UDCOTGICR_IEVV44R (1 << 7) /* OTG Vbus Valid 4.4V Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IEVV44F (1 << 6) /* OTG Vbus Valid 4.4V Falling Edge + Interrupt Enable */ +#define UDCOTGICR_IESVR (1 << 5) /* OTG Session Valid Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IESVF (1 << 4) /* OTG Session Valid Falling Edge + Interrupt Enable */ +#define UDCOTGICR_IESDR (1 << 3) /* OTG A-Device SRP Detect Rising + Edge Interrupt Enable */ +#define UDCOTGICR_IESDF (1 << 2) /* OTG A-Device SRP Detect Falling + Edge Interrupt Enable */ +#define UDCOTGICR_IEIDR (1 << 1) /* OTG ID Change Rising Edge + Interrupt Enable */ +#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge + Interrupt Enable */ + +#define UP2OCR __REG(0x40600020) /* USB Port 2 Output Control register */ + +#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */ +#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */ +#define UP2OCR_DPPDE (1 << 2) /* Host Port 2 Transceiver D+ Pull Down Enable */ +#define UP2OCR_DMPDE (1 << 3) /* Host Port 2 Transceiver D- Pull Down Enable */ +#define UP2OCR_DPPUE (1 << 4) /* Host Port 2 Transceiver D+ Pull Up Enable */ +#define UP2OCR_DMPUE (1 << 5) /* Host Port 2 Transceiver D- Pull Up Enable */ +#define UP2OCR_DPPUBE (1 << 6) /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */ +#define UP2OCR_DMPUBE (1 << 7) /* Host Port 2 Transceiver D- Pull Up Bypass Enable */ +#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */ +#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */ +#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */ +#define UP2OCR_HXS (1 << 16) /* Host Port 2 Transceiver Output Select */ +#define UP2OCR_HXOE (1 << 17) /* Host Port 2 Transceiver Output Enable */ +#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */ + +#define UDCCSN(x) __REG2(0x40600100, (x) << 2) +#define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */ +#define UDCCSR0_SA (1 << 7) /* Setup Active */ +#define UDCCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */ +#define UDCCSR0_FST (1 << 5) /* Force Stall */ +#define UDCCSR0_SST (1 << 4) /* Sent Stall */ +#define UDCCSR0_DME (1 << 3) /* DMA Enable */ +#define UDCCSR0_FTF (1 << 2) /* Flush Transmit FIFO */ +#define UDCCSR0_IPR (1 << 1) /* IN Packet Ready */ +#define UDCCSR0_OPC (1 << 0) /* OUT Packet Complete */ + +#define UDCCSRA __REG(0x40600104) /* UDC Control/Status register - Endpoint A */ +#define UDCCSRB __REG(0x40600108) /* UDC Control/Status register - Endpoint B */ +#define UDCCSRC __REG(0x4060010C) /* UDC Control/Status register - Endpoint C */ +#define UDCCSRD __REG(0x40600110) /* UDC Control/Status register - Endpoint D */ +#define UDCCSRE __REG(0x40600114) /* UDC Control/Status register - Endpoint E */ +#define UDCCSRF __REG(0x40600118) /* UDC Control/Status register - Endpoint F */ +#define UDCCSRG __REG(0x4060011C) /* UDC Control/Status register - Endpoint G */ +#define UDCCSRH __REG(0x40600120) /* UDC Control/Status register - Endpoint H */ +#define UDCCSRI __REG(0x40600124) /* UDC Control/Status register - Endpoint I */ +#define UDCCSRJ __REG(0x40600128) /* UDC Control/Status register - Endpoint J */ +#define UDCCSRK __REG(0x4060012C) /* UDC Control/Status register - Endpoint K */ +#define UDCCSRL __REG(0x40600130) /* UDC Control/Status register - Endpoint L */ +#define UDCCSRM __REG(0x40600134) /* UDC Control/Status register - Endpoint M */ +#define UDCCSRN __REG(0x40600138) /* UDC Control/Status register - Endpoint N */ +#define UDCCSRP __REG(0x4060013C) /* UDC Control/Status register - Endpoint P */ +#define UDCCSRQ __REG(0x40600140) /* UDC Control/Status register - Endpoint Q */ +#define UDCCSRR __REG(0x40600144) /* UDC Control/Status register - Endpoint R */ +#define UDCCSRS __REG(0x40600148) /* UDC Control/Status register - Endpoint S */ +#define UDCCSRT __REG(0x4060014C) /* UDC Control/Status register - Endpoint T */ +#define UDCCSRU __REG(0x40600150) /* UDC Control/Status register - Endpoint U */ +#define UDCCSRV __REG(0x40600154) /* UDC Control/Status register - Endpoint V */ +#define UDCCSRW __REG(0x40600158) /* UDC Control/Status register - Endpoint W */ +#define UDCCSRX __REG(0x4060015C) /* UDC Control/Status register - Endpoint X */ + +#define UDCCSR_DPE (1 << 9) /* Data Packet Error */ +#define UDCCSR_FEF (1 << 8) /* Flush Endpoint FIFO */ +#define UDCCSR_SP (1 << 7) /* Short Packet Control/Status */ +#define UDCCSR_BNE (1 << 6) /* Buffer Not Empty (IN endpoints) */ +#define UDCCSR_BNF (1 << 6) /* Buffer Not Full (OUT endpoints) */ +#define UDCCSR_FST (1 << 5) /* Force STALL */ +#define UDCCSR_SST (1 << 4) /* Sent STALL */ +#define UDCCSR_DME (1 << 3) /* DMA Enable */ +#define UDCCSR_TRN (1 << 2) /* Tx/Rx NAK */ +#define UDCCSR_PC (1 << 1) /* Packet Complete */ +#define UDCCSR_FS (1 << 0) /* FIFO needs service */ + +#define UDCBCN(x) __REG2(0x40600200, (x)<<2) +#define UDCBCR0 __REG(0x40600200) /* Byte Count Register - EP0 */ +#define UDCBCRA __REG(0x40600204) /* Byte Count Register - EPA */ +#define UDCBCRB __REG(0x40600208) /* Byte Count Register - EPB */ +#define UDCBCRC __REG(0x4060020C) /* Byte Count Register - EPC */ +#define UDCBCRD __REG(0x40600210) /* Byte Count Register - EPD */ +#define UDCBCRE __REG(0x40600214) /* Byte Count Register - EPE */ +#define UDCBCRF __REG(0x40600218) /* Byte Count Register - EPF */ +#define UDCBCRG __REG(0x4060021C) /* Byte Count Register - EPG */ +#define UDCBCRH __REG(0x40600220) /* Byte Count Register - EPH */ +#define UDCBCRI __REG(0x40600224) /* Byte Count Register - EPI */ +#define UDCBCRJ __REG(0x40600228) /* Byte Count Register - EPJ */ +#define UDCBCRK __REG(0x4060022C) /* Byte Count Register - EPK */ +#define UDCBCRL __REG(0x40600230) /* Byte Count Register - EPL */ +#define UDCBCRM __REG(0x40600234) /* Byte Count Register - EPM */ +#define UDCBCRN __REG(0x40600238) /* Byte Count Register - EPN */ +#define UDCBCRP __REG(0x4060023C) /* Byte Count Register - EPP */ +#define UDCBCRQ __REG(0x40600240) /* Byte Count Register - EPQ */ +#define UDCBCRR __REG(0x40600244) /* Byte Count Register - EPR */ +#define UDCBCRS __REG(0x40600248) /* Byte Count Register - EPS */ +#define UDCBCRT __REG(0x4060024C) /* Byte Count Register - EPT */ +#define UDCBCRU __REG(0x40600250) /* Byte Count Register - EPU */ +#define UDCBCRV __REG(0x40600254) /* Byte Count Register - EPV */ +#define UDCBCRW __REG(0x40600258) /* Byte Count Register - EPW */ +#define UDCBCRX __REG(0x4060025C) /* Byte Count Register - EPX */ + +#define UDCDN(x) __REG2(0x40600300, (x)<<2) +#define PHYS_UDCDN(x) (0x40600300 + ((x)<<2)) +#define PUDCDN(x) (volatile u32 *)(io_p2v(PHYS_UDCDN((x)))) +#define UDCDR0 __REG(0x40600300) /* Data Register - EP0 */ +#define UDCDRA __REG(0x40600304) /* Data Register - EPA */ +#define UDCDRB __REG(0x40600308) /* Data Register - EPB */ +#define UDCDRC __REG(0x4060030C) /* Data Register - EPC */ +#define UDCDRD __REG(0x40600310) /* Data Register - EPD */ +#define UDCDRE __REG(0x40600314) /* Data Register - EPE */ +#define UDCDRF __REG(0x40600318) /* Data Register - EPF */ +#define UDCDRG __REG(0x4060031C) /* Data Register - EPG */ +#define UDCDRH __REG(0x40600320) /* Data Register - EPH */ +#define UDCDRI __REG(0x40600324) /* Data Register - EPI */ +#define UDCDRJ __REG(0x40600328) /* Data Register - EPJ */ +#define UDCDRK __REG(0x4060032C) /* Data Register - EPK */ +#define UDCDRL __REG(0x40600330) /* Data Register - EPL */ +#define UDCDRM __REG(0x40600334) /* Data Register - EPM */ +#define UDCDRN __REG(0x40600338) /* Data Register - EPN */ +#define UDCDRP __REG(0x4060033C) /* Data Register - EPP */ +#define UDCDRQ __REG(0x40600340) /* Data Register - EPQ */ +#define UDCDRR __REG(0x40600344) /* Data Register - EPR */ +#define UDCDRS __REG(0x40600348) /* Data Register - EPS */ +#define UDCDRT __REG(0x4060034C) /* Data Register - EPT */ +#define UDCDRU __REG(0x40600350) /* Data Register - EPU */ +#define UDCDRV __REG(0x40600354) /* Data Register - EPV */ +#define UDCDRW __REG(0x40600358) /* Data Register - EPW */ +#define UDCDRX __REG(0x4060035C) /* Data Register - EPX */ + +#define UDCCN(x) __REG2(0x40600400, (x)<<2) +#define UDCCRA __REG(0x40600404) /* Configuration register EPA */ +#define UDCCRB __REG(0x40600408) /* Configuration register EPB */ +#define UDCCRC __REG(0x4060040C) /* Configuration register EPC */ +#define UDCCRD __REG(0x40600410) /* Configuration register EPD */ +#define UDCCRE __REG(0x40600414) /* Configuration register EPE */ +#define UDCCRF __REG(0x40600418) /* Configuration register EPF */ +#define UDCCRG __REG(0x4060041C) /* Configuration register EPG */ +#define UDCCRH __REG(0x40600420) /* Configuration register EPH */ +#define UDCCRI __REG(0x40600424) /* Configuration register EPI */ +#define UDCCRJ __REG(0x40600428) /* Configuration register EPJ */ +#define UDCCRK __REG(0x4060042C) /* Configuration register EPK */ +#define UDCCRL __REG(0x40600430) /* Configuration register EPL */ +#define UDCCRM __REG(0x40600434) /* Configuration register EPM */ +#define UDCCRN __REG(0x40600438) /* Configuration register EPN */ +#define UDCCRP __REG(0x4060043C) /* Configuration register EPP */ +#define UDCCRQ __REG(0x40600440) /* Configuration register EPQ */ +#define UDCCRR __REG(0x40600444) /* Configuration register EPR */ +#define UDCCRS __REG(0x40600448) /* Configuration register EPS */ +#define UDCCRT __REG(0x4060044C) /* Configuration register EPT */ +#define UDCCRU __REG(0x40600450) /* Configuration register EPU */ +#define UDCCRV __REG(0x40600454) /* Configuration register EPV */ +#define UDCCRW __REG(0x40600458) /* Configuration register EPW */ +#define UDCCRX __REG(0x4060045C) /* Configuration register EPX */ + +#define UDCCONR_CN (0x03 << 25) /* Configuration Number */ +#define UDCCONR_CN_S (25) +#define UDCCONR_IN (0x07 << 22) /* Interface Number */ +#define UDCCONR_IN_S (22) +#define UDCCONR_AISN (0x07 << 19) /* Alternate Interface Number */ +#define UDCCONR_AISN_S (19) +#define UDCCONR_EN (0x0f << 15) /* Endpoint Number */ +#define UDCCONR_EN_S (15) +#define UDCCONR_ET (0x03 << 13) /* Endpoint Type: */ +#define UDCCONR_ET_S (13) +#define UDCCONR_ET_INT (0x03 << 13) /* Interrupt */ +#define UDCCONR_ET_BULK (0x02 << 13) /* Bulk */ +#define UDCCONR_ET_ISO (0x01 << 13) /* Isochronous */ +#define UDCCONR_ET_NU (0x00 << 13) /* Not used */ +#define UDCCONR_ED (1 << 12) /* Endpoint Direction */ +#define UDCCONR_MPS (0x3ff << 2) /* Maximum Packet Size */ +#define UDCCONR_MPS_S (2) +#define UDCCONR_DE (1 << 1) /* Double Buffering Enable */ +#define UDCCONR_EE (1 << 0) /* Endpoint Enable */ + + +#define UDC_INT_FIFOERROR (0x2) +#define UDC_INT_PACKETCMP (0x1) + +#define UDC_FNR_MASK (0x7ff) + +#define UDCCSR_WR_MASK (UDCCSR_DME|UDCCSR_FST) +#define UDC_BCR_MASK (0x3ff) + +#endif -- cgit v1.2.3 From f70c5253b41444fd2779e1f76bfe25811d9b8c23 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 12:22:36 +0100 Subject: [RTC] remove references to asm/mach/time.h asm/mach/time.h is the ARM header file for setting up kernel ticker timekeeping (be that the old jiffy interrupt or the new clocksource.) RTC drivers have no business using this header file, and in fact do not require it. Build tested on at91sam9rl, omap and s3c2410 configurations. Acked-by: Alessandro Zummo Acked-by: Andrew Victor Signed-off-by: Russell King --- drivers/rtc/rtc-at91rm9200.c | 2 -- drivers/rtc/rtc-at91sam9.c | 1 - drivers/rtc/rtc-omap.c | 1 - drivers/rtc/rtc-s3c.c | 2 -- 4 files changed, 6 deletions(-) diff --git a/drivers/rtc/rtc-at91rm9200.c b/drivers/rtc/rtc-at91rm9200.c index 39e64ab1ecb7..2af1e6fb71c0 100644 --- a/drivers/rtc/rtc-at91rm9200.c +++ b/drivers/rtc/rtc-at91rm9200.c @@ -31,8 +31,6 @@ #include #include -#include - #include diff --git a/drivers/rtc/rtc-at91sam9.c b/drivers/rtc/rtc-at91sam9.c index 38d8742a4bdf..f0246ef413a4 100644 --- a/drivers/rtc/rtc-at91sam9.c +++ b/drivers/rtc/rtc-at91sam9.c @@ -19,7 +19,6 @@ #include #include -#include #include #include diff --git a/drivers/rtc/rtc-omap.c b/drivers/rtc/rtc-omap.c index 58f81c774943..eb23d8423f42 100644 --- a/drivers/rtc/rtc-omap.c +++ b/drivers/rtc/rtc-omap.c @@ -22,7 +22,6 @@ #include #include -#include /* The OMAP1 RTC is a year/month/day/hours/minutes/seconds BCD clock diff --git a/drivers/rtc/rtc-s3c.c b/drivers/rtc/rtc-s3c.c index f26e0cad8f16..2c6e4671e388 100644 --- a/drivers/rtc/rtc-s3c.c +++ b/drivers/rtc/rtc-s3c.c @@ -28,8 +28,6 @@ #include #include -#include - #include /* I have yet to find an S3C implementation with more than one -- cgit v1.2.3 From 2dba8518b7761aee3ba757b298efa15dd34eff18 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 12:08:04 +0100 Subject: [RTC] rtc-pl031: use proper resources, use proper apis, clean up includes Clean up PL031 RTC includes, make driver use proper resource checking, and use amba bus specific accessors. Acked-by: Alessandro Zummo Signed-off-by: Russell King --- drivers/rtc/rtc-pl031.c | 36 +++++++++++++++--------------------- 1 file changed, 15 insertions(+), 21 deletions(-) diff --git a/drivers/rtc/rtc-pl031.c b/drivers/rtc/rtc-pl031.c index 2fd49edcc712..08b4610ec5a6 100644 --- a/drivers/rtc/rtc-pl031.c +++ b/drivers/rtc/rtc-pl031.c @@ -12,23 +12,12 @@ * as published by the Free Software Foundation; either version * 2 of the License, or (at your option) any later version. */ - -#include #include #include #include -#include #include -#include -#include -#include - #include - -#include -#include -#include -#include +#include /* * Register definitions @@ -142,13 +131,12 @@ static int pl031_remove(struct amba_device *adev) { struct pl031_local *ldata = dev_get_drvdata(&adev->dev); - if (ldata) { - dev_set_drvdata(&adev->dev, NULL); - free_irq(adev->irq[0], ldata->rtc); - rtc_device_unregister(ldata->rtc); - iounmap(ldata->base); - kfree(ldata); - } + amba_set_drvdata(adev, NULL); + free_irq(adev->irq[0], ldata->rtc); + rtc_device_unregister(ldata->rtc); + iounmap(ldata->base); + kfree(ldata); + amba_release_regions(adev); return 0; } @@ -158,13 +146,15 @@ static int pl031_probe(struct amba_device *adev, void *id) int ret; struct pl031_local *ldata; + ret = amba_request_regions(adev, NULL); + if (ret) + goto err_req; ldata = kmalloc(sizeof(struct pl031_local), GFP_KERNEL); if (!ldata) { ret = -ENOMEM; goto out; } - dev_set_drvdata(&adev->dev, ldata); ldata->base = ioremap(adev->res.start, adev->res.end - adev->res.start + 1); @@ -173,6 +163,8 @@ static int pl031_probe(struct amba_device *adev, void *id) goto out_no_remap; } + amba_set_drvdata(adev, ldata); + if (request_irq(adev->irq[0], pl031_interrupt, IRQF_DISABLED, "rtc-pl031", ldata->rtc)) { ret = -EIO; @@ -192,10 +184,12 @@ out_no_rtc: free_irq(adev->irq[0], ldata->rtc); out_no_irq: iounmap(ldata->base); + amba_set_drvdata(adev, NULL); out_no_remap: - dev_set_drvdata(&adev->dev, NULL); kfree(ldata); out: + amba_release_regions(adev); +err_req: return ret; } -- cgit v1.2.3 From a190901c6b5f1f4a31681e8c69d811a4f9426e2b Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 12:08:36 +0100 Subject: [RTC] rtc-pl030: add driver, remove old non-rtc lib driver Convert Integrator PL030 RTC driver to use the RTC class interfaces. Acked-by: Alessandro Zummo Signed-off-by: Russell King --- arch/arm/mach-integrator/Makefile | 2 +- arch/arm/mach-integrator/time.c | 223 -------------------------------------- drivers/rtc/Kconfig | 10 ++ drivers/rtc/Makefile | 1 + drivers/rtc/rtc-pl030.c | 217 +++++++++++++++++++++++++++++++++++++ 5 files changed, 229 insertions(+), 224 deletions(-) delete mode 100644 arch/arm/mach-integrator/time.c create mode 100644 drivers/rtc/rtc-pl030.c diff --git a/arch/arm/mach-integrator/Makefile b/arch/arm/mach-integrator/Makefile index 158daaf9e3b0..6a5ef8d30b10 100644 --- a/arch/arm/mach-integrator/Makefile +++ b/arch/arm/mach-integrator/Makefile @@ -4,7 +4,7 @@ # Object file lists. -obj-y := clock.o core.o lm.o time.o +obj-y := clock.o core.o lm.o obj-$(CONFIG_ARCH_INTEGRATOR_AP) += integrator_ap.o obj-$(CONFIG_ARCH_INTEGRATOR_CP) += integrator_cp.o diff --git a/arch/arm/mach-integrator/time.c b/arch/arm/mach-integrator/time.c deleted file mode 100644 index 8508a0db3eaf..000000000000 --- a/arch/arm/mach-integrator/time.c +++ /dev/null @@ -1,223 +0,0 @@ -/* - * linux/arch/arm/mach-integrator/time.c - * - * Copyright (C) 2000-2001 Deep Blue Solutions Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include - -#define RTC_DR (0) -#define RTC_MR (4) -#define RTC_STAT (8) -#define RTC_EOI (8) -#define RTC_LR (12) -#define RTC_CR (16) -#define RTC_CR_MIE (1 << 0) - -extern int (*set_rtc)(void); -static void __iomem *rtc_base; - -static int integrator_set_rtc(void) -{ - __raw_writel(xtime.tv_sec, rtc_base + RTC_LR); - return 1; -} - -static int integrator_rtc_read_alarm(struct rtc_wkalrm *alrm) -{ - rtc_time_to_tm(readl(rtc_base + RTC_MR), &alrm->time); - return 0; -} - -static inline int integrator_rtc_set_alarm(struct rtc_wkalrm *alrm) -{ - unsigned long time; - int ret; - - /* - * At the moment, we can only deal with non-wildcarded alarm times. - */ - ret = rtc_valid_tm(&alrm->time); - if (ret == 0) - ret = rtc_tm_to_time(&alrm->time, &time); - if (ret == 0) - writel(time, rtc_base + RTC_MR); - return ret; -} - -static int integrator_rtc_read_time(struct rtc_time *tm) -{ - rtc_time_to_tm(readl(rtc_base + RTC_DR), tm); - return 0; -} - -/* - * Set the RTC time. Unfortunately, we can't accurately set - * the point at which the counter updates. - * - * Also, since RTC_LR is transferred to RTC_CR on next rising - * edge of the 1Hz clock, we must write the time one second - * in advance. - */ -static inline int integrator_rtc_set_time(struct rtc_time *tm) -{ - unsigned long time; - int ret; - - ret = rtc_tm_to_time(tm, &time); - if (ret == 0) - writel(time + 1, rtc_base + RTC_LR); - - return ret; -} - -static struct rtc_ops rtc_ops = { - .owner = THIS_MODULE, - .read_time = integrator_rtc_read_time, - .set_time = integrator_rtc_set_time, - .read_alarm = integrator_rtc_read_alarm, - .set_alarm = integrator_rtc_set_alarm, -}; - -static irqreturn_t arm_rtc_interrupt(int irq, void *dev_id) -{ - writel(0, rtc_base + RTC_EOI); - return IRQ_HANDLED; -} - -static int rtc_probe(struct amba_device *dev, void *id) -{ - int ret; - - if (rtc_base) - return -EBUSY; - - ret = amba_request_regions(dev, NULL); - if (ret) - goto out; - - rtc_base = ioremap(dev->res.start, SZ_4K); - if (!rtc_base) { - ret = -ENOMEM; - goto res_out; - } - - __raw_writel(0, rtc_base + RTC_CR); - __raw_writel(0, rtc_base + RTC_EOI); - - xtime.tv_sec = __raw_readl(rtc_base + RTC_DR); - - /* note that 'dev' is merely used for irq disambiguation; - * it is not actually referenced in the irq handler - */ - ret = request_irq(dev->irq[0], arm_rtc_interrupt, IRQF_DISABLED, - "rtc-pl030", dev); - if (ret) - goto map_out; - - ret = register_rtc(&rtc_ops); - if (ret) - goto irq_out; - - set_rtc = integrator_set_rtc; - return 0; - - irq_out: - free_irq(dev->irq[0], dev); - map_out: - iounmap(rtc_base); - rtc_base = NULL; - res_out: - amba_release_regions(dev); - out: - return ret; -} - -static int rtc_remove(struct amba_device *dev) -{ - set_rtc = NULL; - - writel(0, rtc_base + RTC_CR); - - free_irq(dev->irq[0], dev); - unregister_rtc(&rtc_ops); - - iounmap(rtc_base); - rtc_base = NULL; - amba_release_regions(dev); - - return 0; -} - -static struct timespec rtc_delta; - -static int rtc_suspend(struct amba_device *dev, pm_message_t state) -{ - struct timespec rtc; - - rtc.tv_sec = readl(rtc_base + RTC_DR); - rtc.tv_nsec = 0; - save_time_delta(&rtc_delta, &rtc); - - return 0; -} - -static int rtc_resume(struct amba_device *dev) -{ - struct timespec rtc; - - rtc.tv_sec = readl(rtc_base + RTC_DR); - rtc.tv_nsec = 0; - restore_time_delta(&rtc_delta, &rtc); - - return 0; -} - -static struct amba_id rtc_ids[] = { - { - .id = 0x00041030, - .mask = 0x000fffff, - }, - { 0, 0 }, -}; - -static struct amba_driver rtc_driver = { - .drv = { - .name = "rtc-pl030", - }, - .probe = rtc_probe, - .remove = rtc_remove, - .suspend = rtc_suspend, - .resume = rtc_resume, - .id_table = rtc_ids, -}; - -static int __init integrator_rtc_init(void) -{ - return amba_driver_register(&rtc_driver); -} - -static void __exit integrator_rtc_exit(void) -{ - amba_driver_unregister(&rtc_driver); -} - -module_init(integrator_rtc_init); -module_exit(integrator_rtc_exit); diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig index 6cc2c0330230..1b26eeb52c97 100644 --- a/drivers/rtc/Kconfig +++ b/drivers/rtc/Kconfig @@ -458,6 +458,16 @@ config RTC_DRV_VR41XX To compile this driver as a module, choose M here: the module will be called rtc-vr41xx. +config RTC_DRV_PL030 + tristate "ARM AMBA PL030 RTC" + depends on ARM_AMBA + help + If you say Y here you will get access to ARM AMBA + PrimeCell PL030 RTC found on certain ARM SOCs. + + To compile this driver as a module, choose M here: the + module will be called rtc-pl030. + config RTC_DRV_PL031 tristate "ARM AMBA PL031 RTC" depends on ARM_AMBA diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile index 872f1218ff9f..af3ee6652ce5 100644 --- a/drivers/rtc/Makefile +++ b/drivers/rtc/Makefile @@ -40,6 +40,7 @@ obj-$(CONFIG_RTC_DRV_MAX6902) += rtc-max6902.o obj-$(CONFIG_RTC_DRV_OMAP) += rtc-omap.o obj-$(CONFIG_RTC_DRV_PCF8563) += rtc-pcf8563.o obj-$(CONFIG_RTC_DRV_PCF8583) += rtc-pcf8583.o +obj-$(CONFIG_RTC_DRV_PL030) += rtc-pl030.o obj-$(CONFIG_RTC_DRV_PL031) += rtc-pl031.o obj-$(CONFIG_RTC_DRV_R9701) += rtc-r9701.o obj-$(CONFIG_RTC_DRV_RS5C313) += rtc-rs5c313.o diff --git a/drivers/rtc/rtc-pl030.c b/drivers/rtc/rtc-pl030.c new file mode 100644 index 000000000000..8448eeb9d675 --- /dev/null +++ b/drivers/rtc/rtc-pl030.c @@ -0,0 +1,217 @@ +/* + * linux/drivers/rtc/rtc-pl030.c + * + * Copyright (C) 2000-2001 Deep Blue Solutions Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include +#include +#include +#include +#include +#include + +#define RTC_DR (0) +#define RTC_MR (4) +#define RTC_STAT (8) +#define RTC_EOI (8) +#define RTC_LR (12) +#define RTC_CR (16) +#define RTC_CR_MIE (1 << 0) + +struct pl030_rtc { + struct rtc_device *rtc; + void __iomem *base; +}; + +static irqreturn_t pl030_interrupt(int irq, void *dev_id) +{ + struct pl030_rtc *rtc = dev_id; + writel(0, rtc->base + RTC_EOI); + return IRQ_HANDLED; +} + +static int pl030_open(struct device *dev) +{ + return 0; +} + +static void pl030_release(struct device *dev) +{ +} + +static int pl030_ioctl(struct device *dev, unsigned int cmd, unsigned long arg) +{ + return -ENOIOCTLCMD; +} + +static int pl030_read_alarm(struct device *dev, struct rtc_wkalrm *alrm) +{ + struct pl030_rtc *rtc = dev_get_drvdata(dev); + + rtc_time_to_tm(readl(rtc->base + RTC_MR), &alrm->time); + return 0; +} + +static int pl030_set_alarm(struct device *dev, struct rtc_wkalrm *alrm) +{ + struct pl030_rtc *rtc = dev_get_drvdata(dev); + unsigned long time; + int ret; + + /* + * At the moment, we can only deal with non-wildcarded alarm times. + */ + ret = rtc_valid_tm(&alrm->time); + if (ret == 0) + ret = rtc_tm_to_time(&alrm->time, &time); + if (ret == 0) + writel(time, rtc->base + RTC_MR); + return ret; +} + +static int pl030_read_time(struct device *dev, struct rtc_time *tm) +{ + struct pl030_rtc *rtc = dev_get_drvdata(dev); + + rtc_time_to_tm(readl(rtc->base + RTC_DR), tm); + + return 0; +} + +/* + * Set the RTC time. Unfortunately, we can't accurately set + * the point at which the counter updates. + * + * Also, since RTC_LR is transferred to RTC_CR on next rising + * edge of the 1Hz clock, we must write the time one second + * in advance. + */ +static int pl030_set_time(struct device *dev, struct rtc_time *tm) +{ + struct pl030_rtc *rtc = dev_get_drvdata(dev); + unsigned long time; + int ret; + + ret = rtc_tm_to_time(tm, &time); + if (ret == 0) + writel(time + 1, rtc->base + RTC_LR); + + return ret; +} + +static const struct rtc_class_ops pl030_ops = { + .open = pl030_open, + .release = pl030_release, + .ioctl = pl030_ioctl, + .read_time = pl030_read_time, + .set_time = pl030_set_time, + .read_alarm = pl030_read_alarm, + .set_alarm = pl030_set_alarm, +}; + +static int pl030_probe(struct amba_device *dev, void *id) +{ + struct pl030_rtc *rtc; + int ret; + + ret = amba_request_regions(dev, NULL); + if (ret) + goto err_req; + + rtc = kmalloc(sizeof(*rtc), GFP_KERNEL); + if (!rtc) { + ret = -ENOMEM; + goto err_rtc; + } + + rtc->base = ioremap(dev->res.start, SZ_4K); + if (!rtc->base) { + ret = -ENOMEM; + goto err_map; + } + + __raw_writel(0, rtc->base + RTC_CR); + __raw_writel(0, rtc->base + RTC_EOI); + + amba_set_drvdata(dev, rtc); + + ret = request_irq(dev->irq[0], pl030_interrupt, IRQF_DISABLED, + "rtc-pl030", rtc); + if (ret) + goto err_irq; + + rtc->rtc = rtc_device_register("pl030", &dev->dev, &pl030_ops, + THIS_MODULE); + if (IS_ERR(rtc->rtc)) { + ret = PTR_ERR(rtc->rtc); + goto err_reg; + } + + return 0; + + err_reg: + free_irq(dev->irq[0], rtc); + err_irq: + iounmap(rtc->base); + err_map: + kfree(rtc); + err_rtc: + amba_release_regions(dev); + err_req: + return ret; +} + +static int pl030_remove(struct amba_device *dev) +{ + struct pl030_rtc *rtc = amba_get_drvdata(dev); + + amba_set_drvdata(dev, NULL); + + writel(0, rtc->base + RTC_CR); + + free_irq(dev->irq[0], rtc); + rtc_device_unregister(rtc->rtc); + iounmap(rtc->base); + kfree(rtc); + amba_release_regions(dev); + + return 0; +} + +static struct amba_id pl030_ids[] = { + { + .id = 0x00041030, + .mask = 0x000fffff, + }, + { 0, 0 }, +}; + +static struct amba_driver pl030_driver = { + .drv = { + .name = "rtc-pl030", + }, + .probe = pl030_probe, + .remove = pl030_remove, + .id_table = pl030_ids, +}; + +static int __init pl030_init(void) +{ + return amba_driver_register(&pl030_driver); +} + +static void __exit pl030_exit(void) +{ + amba_driver_unregister(&pl030_driver); +} + +module_init(pl030_init); +module_exit(pl030_exit); + +MODULE_AUTHOR("Russell King "); +MODULE_DESCRIPTION("ARM AMBA PL030 RTC Driver"); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From 7da285b626860eb6d35e08ae33eba90f0e83ad58 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 12:26:48 +0100 Subject: [RTC] remove unused asm/rtc.h includes from ARM RTC drivers On ARM, asm/rtc.h only contains definitions for the predecessor to the RTC class support. RTC class drivers should not be including this include. Build tested on at91sam9rl and s3c2410 configurations. Acked-by: Alessandro Zummo Signed-off-by: Russell King --- drivers/rtc/rtc-at91rm9200.c | 2 -- drivers/rtc/rtc-s3c.c | 2 -- 2 files changed, 4 deletions(-) diff --git a/drivers/rtc/rtc-at91rm9200.c b/drivers/rtc/rtc-at91rm9200.c index 2af1e6fb71c0..9c3db934cc24 100644 --- a/drivers/rtc/rtc-at91rm9200.c +++ b/drivers/rtc/rtc-at91rm9200.c @@ -29,8 +29,6 @@ #include #include -#include - #include diff --git a/drivers/rtc/rtc-s3c.c b/drivers/rtc/rtc-s3c.c index 2c6e4671e388..fed86e507fdf 100644 --- a/drivers/rtc/rtc-s3c.c +++ b/drivers/rtc/rtc-s3c.c @@ -26,8 +26,6 @@ #include #include #include -#include - #include /* I have yet to find an S3C implementation with more than one -- cgit v1.2.3 From 797276ec9e4d2ee210e11068a2ce815394fe8c58 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 12:30:41 +0100 Subject: [RTC] rtc-sa1100: remove dependence on asm/rtc.h Move the two functions rtc-sa1100 wants from the old ARM RTC library into the rtc-sa1100 driver. Acked-by: Alessandro Zummo Signed-off-by: Russell King --- drivers/rtc/rtc-sa1100.c | 37 ++++++++++++++++++++++++++++++++++++- 1 file changed, 36 insertions(+), 1 deletion(-) diff --git a/drivers/rtc/rtc-sa1100.c b/drivers/rtc/rtc-sa1100.c index 82f62d25f921..e31a687b44b9 100644 --- a/drivers/rtc/rtc-sa1100.c +++ b/drivers/rtc/rtc-sa1100.c @@ -33,7 +33,6 @@ #include #include -#include #ifdef CONFIG_ARCH_PXA #include @@ -47,6 +46,42 @@ static unsigned long rtc_freq = 1024; static struct rtc_time rtc_alarm; static DEFINE_SPINLOCK(sa1100_rtc_lock); +static inline int rtc_periodic_alarm(struct rtc_time *tm) +{ + return (tm->tm_year == -1) || + ((unsigned)tm->tm_mon >= 12) || + ((unsigned)(tm->tm_mday - 1) >= 31) || + ((unsigned)tm->tm_hour > 23) || + ((unsigned)tm->tm_min > 59) || + ((unsigned)tm->tm_sec > 59); +} + +/* + * Calculate the next alarm time given the requested alarm time mask + * and the current time. + */ +static void rtc_next_alarm_time(struct rtc_time *next, struct rtc_time *now, struct rtc_time *alrm) +{ + unsigned long next_time; + unsigned long now_time; + + next->tm_year = now->tm_year; + next->tm_mon = now->tm_mon; + next->tm_mday = now->tm_mday; + next->tm_hour = alrm->tm_hour; + next->tm_min = alrm->tm_min; + next->tm_sec = alrm->tm_sec; + + rtc_tm_to_time(now, &now_time); + rtc_tm_to_time(next, &next_time); + + if (next_time < now_time) { + /* Advance one day */ + next_time += 60 * 60 * 24; + rtc_time_to_tm(next_time, next); + } +} + static int rtc_update_alarm(struct rtc_time *alrm) { struct rtc_time alarm_tm, now_tm; -- cgit v1.2.3 From bedd78ca786c1d18c2a2785c7e40593dc9c9870f Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 12:31:29 +0100 Subject: [RTC] remove old ARM rtc library code Now that all drivers using it are gone, remove the old ARM RTC library. Acked-by: Alessandro Zummo Signed-off-by: Russell King --- arch/arm/common/Makefile | 1 - arch/arm/common/rtctime.c | 434 ---------------------------------------------- include/asm-arm/rtc.h | 43 ----- 3 files changed, 478 deletions(-) delete mode 100644 arch/arm/common/rtctime.c delete mode 100644 include/asm-arm/rtc.h diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile index 3d0b9fa42f84..325e4b6a6afb 100644 --- a/arch/arm/common/Makefile +++ b/arch/arm/common/Makefile @@ -2,7 +2,6 @@ # Makefile for the linux kernel. # -obj-y += rtctime.o obj-$(CONFIG_ARM_GIC) += gic.o obj-$(CONFIG_ARM_VIC) += vic.o obj-$(CONFIG_ICST525) += icst525.o diff --git a/arch/arm/common/rtctime.c b/arch/arm/common/rtctime.c deleted file mode 100644 index aa8f7739c822..000000000000 --- a/arch/arm/common/rtctime.c +++ /dev/null @@ -1,434 +0,0 @@ -/* - * linux/arch/arm/common/rtctime.c - * - * Copyright (C) 2003 Deep Blue Solutions Ltd. - * Based on sa1100-rtc.c, Nils Faerber, CIH, Nicolas Pitre. - * Based on rtc.c by Paul Gortmaker - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include - -static DECLARE_WAIT_QUEUE_HEAD(rtc_wait); -static struct fasync_struct *rtc_async_queue; - -/* - * rtc_lock protects rtc_irq_data - */ -static DEFINE_SPINLOCK(rtc_lock); -static unsigned long rtc_irq_data; - -/* - * rtc_sem protects rtc_inuse and rtc_ops - */ -static DEFINE_MUTEX(rtc_mutex); -static unsigned long rtc_inuse; -static struct rtc_ops *rtc_ops; - -#define rtc_epoch 1900UL - -/* - * Calculate the next alarm time given the requested alarm time mask - * and the current time. - */ -void rtc_next_alarm_time(struct rtc_time *next, struct rtc_time *now, struct rtc_time *alrm) -{ - unsigned long next_time; - unsigned long now_time; - - next->tm_year = now->tm_year; - next->tm_mon = now->tm_mon; - next->tm_mday = now->tm_mday; - next->tm_hour = alrm->tm_hour; - next->tm_min = alrm->tm_min; - next->tm_sec = alrm->tm_sec; - - rtc_tm_to_time(now, &now_time); - rtc_tm_to_time(next, &next_time); - - if (next_time < now_time) { - /* Advance one day */ - next_time += 60 * 60 * 24; - rtc_time_to_tm(next_time, next); - } -} -EXPORT_SYMBOL(rtc_next_alarm_time); - -static inline int rtc_arm_read_time(struct rtc_ops *ops, struct rtc_time *tm) -{ - memset(tm, 0, sizeof(struct rtc_time)); - return ops->read_time(tm); -} - -static inline int rtc_arm_set_time(struct rtc_ops *ops, struct rtc_time *tm) -{ - int ret; - - ret = rtc_valid_tm(tm); - if (ret == 0) - ret = ops->set_time(tm); - - return ret; -} - -static inline int rtc_arm_read_alarm(struct rtc_ops *ops, struct rtc_wkalrm *alrm) -{ - int ret = -EINVAL; - if (ops->read_alarm) { - memset(alrm, 0, sizeof(struct rtc_wkalrm)); - ret = ops->read_alarm(alrm); - } - return ret; -} - -static inline int rtc_arm_set_alarm(struct rtc_ops *ops, struct rtc_wkalrm *alrm) -{ - int ret = -EINVAL; - if (ops->set_alarm) - ret = ops->set_alarm(alrm); - return ret; -} - -void rtc_update(unsigned long num, unsigned long events) -{ - spin_lock(&rtc_lock); - rtc_irq_data = (rtc_irq_data + (num << 8)) | events; - spin_unlock(&rtc_lock); - - wake_up_interruptible(&rtc_wait); - kill_fasync(&rtc_async_queue, SIGIO, POLL_IN); -} -EXPORT_SYMBOL(rtc_update); - - -static ssize_t -rtc_read(struct file *file, char __user *buf, size_t count, loff_t *ppos) -{ - DECLARE_WAITQUEUE(wait, current); - unsigned long data; - ssize_t ret; - - if (count < sizeof(unsigned long)) - return -EINVAL; - - add_wait_queue(&rtc_wait, &wait); - do { - __set_current_state(TASK_INTERRUPTIBLE); - - spin_lock_irq(&rtc_lock); - data = rtc_irq_data; - rtc_irq_data = 0; - spin_unlock_irq(&rtc_lock); - - if (data != 0) { - ret = 0; - break; - } - if (file->f_flags & O_NONBLOCK) { - ret = -EAGAIN; - break; - } - if (signal_pending(current)) { - ret = -ERESTARTSYS; - break; - } - schedule(); - } while (1); - set_current_state(TASK_RUNNING); - remove_wait_queue(&rtc_wait, &wait); - - if (ret == 0) { - ret = put_user(data, (unsigned long __user *)buf); - if (ret == 0) - ret = sizeof(unsigned long); - } - return ret; -} - -static unsigned int rtc_poll(struct file *file, poll_table *wait) -{ - unsigned long data; - - poll_wait(file, &rtc_wait, wait); - - spin_lock_irq(&rtc_lock); - data = rtc_irq_data; - spin_unlock_irq(&rtc_lock); - - return data != 0 ? POLLIN | POLLRDNORM : 0; -} - -static int rtc_ioctl(struct inode *inode, struct file *file, unsigned int cmd, - unsigned long arg) -{ - struct rtc_ops *ops = file->private_data; - struct rtc_time tm; - struct rtc_wkalrm alrm; - void __user *uarg = (void __user *)arg; - int ret = -EINVAL; - - switch (cmd) { - case RTC_ALM_READ: - ret = rtc_arm_read_alarm(ops, &alrm); - if (ret) - break; - ret = copy_to_user(uarg, &alrm.time, sizeof(tm)); - if (ret) - ret = -EFAULT; - break; - - case RTC_ALM_SET: - ret = copy_from_user(&alrm.time, uarg, sizeof(tm)); - if (ret) { - ret = -EFAULT; - break; - } - alrm.enabled = 0; - alrm.pending = 0; - alrm.time.tm_mday = -1; - alrm.time.tm_mon = -1; - alrm.time.tm_year = -1; - alrm.time.tm_wday = -1; - alrm.time.tm_yday = -1; - alrm.time.tm_isdst = -1; - ret = rtc_arm_set_alarm(ops, &alrm); - break; - - case RTC_RD_TIME: - ret = rtc_arm_read_time(ops, &tm); - if (ret) - break; - ret = copy_to_user(uarg, &tm, sizeof(tm)); - if (ret) - ret = -EFAULT; - break; - - case RTC_SET_TIME: - if (!capable(CAP_SYS_TIME)) { - ret = -EACCES; - break; - } - ret = copy_from_user(&tm, uarg, sizeof(tm)); - if (ret) { - ret = -EFAULT; - break; - } - ret = rtc_arm_set_time(ops, &tm); - break; - - case RTC_EPOCH_SET: -#ifndef rtc_epoch - /* - * There were no RTC clocks before 1900. - */ - if (arg < 1900) { - ret = -EINVAL; - break; - } - if (!capable(CAP_SYS_TIME)) { - ret = -EACCES; - break; - } - rtc_epoch = arg; - ret = 0; -#endif - break; - - case RTC_EPOCH_READ: - ret = put_user(rtc_epoch, (unsigned long __user *)uarg); - break; - - case RTC_WKALM_SET: - ret = copy_from_user(&alrm, uarg, sizeof(alrm)); - if (ret) { - ret = -EFAULT; - break; - } - ret = rtc_arm_set_alarm(ops, &alrm); - break; - - case RTC_WKALM_RD: - ret = rtc_arm_read_alarm(ops, &alrm); - if (ret) - break; - ret = copy_to_user(uarg, &alrm, sizeof(alrm)); - if (ret) - ret = -EFAULT; - break; - - default: - if (ops->ioctl) - ret = ops->ioctl(cmd, arg); - break; - } - return ret; -} - -static int rtc_open(struct inode *inode, struct file *file) -{ - int ret; - - mutex_lock(&rtc_mutex); - - if (rtc_inuse) { - ret = -EBUSY; - } else if (!rtc_ops || !try_module_get(rtc_ops->owner)) { - ret = -ENODEV; - } else { - file->private_data = rtc_ops; - - ret = rtc_ops->open ? rtc_ops->open() : 0; - if (ret == 0) { - spin_lock_irq(&rtc_lock); - rtc_irq_data = 0; - spin_unlock_irq(&rtc_lock); - - rtc_inuse = 1; - } - } - mutex_unlock(&rtc_mutex); - - return ret; -} - -static int rtc_release(struct inode *inode, struct file *file) -{ - struct rtc_ops *ops = file->private_data; - - if (ops->release) - ops->release(); - - spin_lock_irq(&rtc_lock); - rtc_irq_data = 0; - spin_unlock_irq(&rtc_lock); - - module_put(rtc_ops->owner); - rtc_inuse = 0; - - return 0; -} - -static int rtc_fasync(int fd, struct file *file, int on) -{ - return fasync_helper(fd, file, on, &rtc_async_queue); -} - -static const struct file_operations rtc_fops = { - .owner = THIS_MODULE, - .llseek = no_llseek, - .read = rtc_read, - .poll = rtc_poll, - .ioctl = rtc_ioctl, - .open = rtc_open, - .release = rtc_release, - .fasync = rtc_fasync, -}; - -static struct miscdevice rtc_miscdev = { - .minor = RTC_MINOR, - .name = "rtc", - .fops = &rtc_fops, -}; - - -static int rtc_read_proc(char *page, char **start, off_t off, int count, int *eof, void *data) -{ - struct rtc_ops *ops = data; - struct rtc_wkalrm alrm; - struct rtc_time tm; - char *p = page; - - if (rtc_arm_read_time(ops, &tm) == 0) { - p += sprintf(p, - "rtc_time\t: %02d:%02d:%02d\n" - "rtc_date\t: %04d-%02d-%02d\n" - "rtc_epoch\t: %04lu\n", - tm.tm_hour, tm.tm_min, tm.tm_sec, - tm.tm_year + 1900, tm.tm_mon + 1, tm.tm_mday, - rtc_epoch); - } - - if (rtc_arm_read_alarm(ops, &alrm) == 0) { - p += sprintf(p, "alrm_time\t: "); - if ((unsigned int)alrm.time.tm_hour <= 24) - p += sprintf(p, "%02d:", alrm.time.tm_hour); - else - p += sprintf(p, "**:"); - if ((unsigned int)alrm.time.tm_min <= 59) - p += sprintf(p, "%02d:", alrm.time.tm_min); - else - p += sprintf(p, "**:"); - if ((unsigned int)alrm.time.tm_sec <= 59) - p += sprintf(p, "%02d\n", alrm.time.tm_sec); - else - p += sprintf(p, "**\n"); - - p += sprintf(p, "alrm_date\t: "); - if ((unsigned int)alrm.time.tm_year <= 200) - p += sprintf(p, "%04d-", alrm.time.tm_year + 1900); - else - p += sprintf(p, "****-"); - if ((unsigned int)alrm.time.tm_mon <= 11) - p += sprintf(p, "%02d-", alrm.time.tm_mon + 1); - else - p += sprintf(p, "**-"); - if ((unsigned int)alrm.time.tm_mday <= 31) - p += sprintf(p, "%02d\n", alrm.time.tm_mday); - else - p += sprintf(p, "**\n"); - p += sprintf(p, "alrm_wakeup\t: %s\n", - alrm.enabled ? "yes" : "no"); - p += sprintf(p, "alrm_pending\t: %s\n", - alrm.pending ? "yes" : "no"); - } - - if (ops->proc) - p += ops->proc(p); - - return p - page; -} - -int register_rtc(struct rtc_ops *ops) -{ - int ret = -EBUSY; - - mutex_lock(&rtc_mutex); - if (rtc_ops == NULL) { - rtc_ops = ops; - - ret = misc_register(&rtc_miscdev); - if (ret == 0) - create_proc_read_entry("driver/rtc", 0, NULL, - rtc_read_proc, ops); - } - mutex_unlock(&rtc_mutex); - - return ret; -} -EXPORT_SYMBOL(register_rtc); - -void unregister_rtc(struct rtc_ops *rtc) -{ - mutex_lock(&rtc_mutex); - if (rtc == rtc_ops) { - remove_proc_entry("driver/rtc", NULL); - misc_deregister(&rtc_miscdev); - rtc_ops = NULL; - } - mutex_unlock(&rtc_mutex); -} -EXPORT_SYMBOL(unregister_rtc); diff --git a/include/asm-arm/rtc.h b/include/asm-arm/rtc.h deleted file mode 100644 index 1a5c9232a91e..000000000000 --- a/include/asm-arm/rtc.h +++ /dev/null @@ -1,43 +0,0 @@ -/* - * linux/include/asm-arm/rtc.h - * - * Copyright (C) 2003 Deep Blue Solutions Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#ifndef ASMARM_RTC_H -#define ASMARM_RTC_H - -struct module; - -struct rtc_ops { - struct module *owner; - int (*open)(void); - void (*release)(void); - int (*ioctl)(unsigned int, unsigned long); - - int (*read_time)(struct rtc_time *); - int (*set_time)(struct rtc_time *); - int (*read_alarm)(struct rtc_wkalrm *); - int (*set_alarm)(struct rtc_wkalrm *); - int (*proc)(char *buf); -}; - -void rtc_next_alarm_time(struct rtc_time *, struct rtc_time *, struct rtc_time *); -void rtc_update(unsigned long, unsigned long); -int register_rtc(struct rtc_ops *); -void unregister_rtc(struct rtc_ops *); - -static inline int rtc_periodic_alarm(struct rtc_time *tm) -{ - return (tm->tm_year == -1) || - ((unsigned)tm->tm_mon >= 12) || - ((unsigned)(tm->tm_mday - 1) >= 31) || - ((unsigned)tm->tm_hour > 23) || - ((unsigned)tm->tm_min > 59) || - ((unsigned)tm->tm_sec > 59); -} - -#endif -- cgit v1.2.3 From 8ff7f2a46bd8831e1f1f2a694ec13921720180b7 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Thu, 21 Feb 2008 16:30:10 +0100 Subject: There is no need to have BOOT_PARAMS_SIZE known outside of atags.c MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit atags.c was the only user of KEXEC_BOOT_PARAMS_SIZE and kexec.h was only included to get that definition. Signed-off-by: Uwe Kleine-König Acked-by: Uli Luckas --- arch/arm/kernel/atags.c | 7 +++---- include/asm-arm/kexec.h | 2 -- 2 files changed, 3 insertions(+), 6 deletions(-) diff --git a/arch/arm/kernel/atags.c b/arch/arm/kernel/atags.c index 64c420805e6f..56fef9a05504 100644 --- a/arch/arm/kernel/atags.c +++ b/arch/arm/kernel/atags.c @@ -1,5 +1,4 @@ #include -#include #include #include #include @@ -42,14 +41,14 @@ create_proc_entries(void) return 0; } - -static char __initdata atags_copy_buf[KEXEC_BOOT_PARAMS_SIZE]; +#define BOOT_PARAMS_SIZE 1536 +static char __initdata atags_copy_buf[BOOT_PARAMS_SIZE]; static char __initdata *atags_copy; void __init save_atags(const struct tag *tags) { atags_copy = atags_copy_buf; - memcpy(atags_copy, tags, KEXEC_BOOT_PARAMS_SIZE); + memcpy(atags_copy, tags, sizeof(atags_copy_buf)); } diff --git a/include/asm-arm/kexec.h b/include/asm-arm/kexec.h index 47fe34d692da..c8986bb99ed5 100644 --- a/include/asm-arm/kexec.h +++ b/include/asm-arm/kexec.h @@ -14,8 +14,6 @@ #define KEXEC_ARCH KEXEC_ARCH_ARM -#define KEXEC_BOOT_PARAMS_SIZE 1536 - #define KEXEC_ARM_ATAGS_OFFSET 0x1000 #define KEXEC_ARM_ZIMAGE_OFFSET 0x8000 -- cgit v1.2.3 From f7b0b939d54b457ba172e088f477af2012aef9b3 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Thu, 21 Feb 2008 15:04:40 +0100 Subject: clean up atags exporting code MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This gets rid of two static variables (one of them being __initdata) and a static function. Signed-off-by: Uwe Kleine-König Acked-by: Uli Luckas --- arch/arm/kernel/atags.c | 80 ++++++++++++++++++++++++------------------------- 1 file changed, 39 insertions(+), 41 deletions(-) diff --git a/arch/arm/kernel/atags.c b/arch/arm/kernel/atags.c index 56fef9a05504..42a1a1415fa6 100644 --- a/arch/arm/kernel/atags.c +++ b/arch/arm/kernel/atags.c @@ -6,9 +6,8 @@ struct buffer { size_t size; - char *data; + char data[]; }; -static struct buffer tags_buffer; static int read_buffer(char* page, char** start, off_t off, int count, @@ -28,58 +27,57 @@ read_buffer(char* page, char** start, off_t off, int count, return count; } - -static int -create_proc_entries(void) -{ - struct proc_dir_entry* tags_entry; - - tags_entry = create_proc_read_entry("atags", 0400, NULL, read_buffer, &tags_buffer); - if (!tags_entry) - return -ENOMEM; - - return 0; -} - #define BOOT_PARAMS_SIZE 1536 -static char __initdata atags_copy_buf[BOOT_PARAMS_SIZE]; -static char __initdata *atags_copy; +static char __initdata atags_copy[BOOT_PARAMS_SIZE]; void __init save_atags(const struct tag *tags) { - atags_copy = atags_copy_buf; - memcpy(atags_copy, tags, sizeof(atags_copy_buf)); + memcpy(atags_copy, tags, sizeof(atags_copy)); } - static int __init init_atags_procfs(void) { - struct tag *tag; - int error; + /* + * This cannot go into save_atags() because kmalloc and proc don't work + * yet when it is called. + */ + struct proc_dir_entry *tags_entry; + struct tag *tag = (struct tag *)atags_copy; + struct buffer *b; + size_t size; - if (!atags_copy) { - printk(KERN_WARNING "Exporting ATAGs: No saved tags found\n"); - return -EIO; + if (tag->hdr.tag != ATAG_CORE) { + printk(KERN_INFO "No ATAGs?"); + return -EINVAL; } - for (tag = (struct tag *) atags_copy; tag->hdr.size; tag = tag_next(tag)) + for (; tag->hdr.size; tag = tag_next(tag)) ; - tags_buffer.size = ((char *) tag - atags_copy) + sizeof(tag->hdr); - tags_buffer.data = kmalloc(tags_buffer.size, GFP_KERNEL); - if (tags_buffer.data == NULL) - return -ENOMEM; - memcpy(tags_buffer.data, atags_copy, tags_buffer.size); - - error = create_proc_entries(); - if (error) { - printk(KERN_ERR "Exporting ATAGs: not enough memory\n"); - kfree(tags_buffer.data); - tags_buffer.size = 0; - tags_buffer.data = NULL; - } + /* include the terminating ATAG_NONE */ + size = (char *)tag - atags_copy + sizeof(struct tag_header); - return error; -} + WARN_ON(tag->hdr.tag != ATAG_NONE); + + b = kmalloc(sizeof(*b) + size, GFP_KERNEL); + if (!b) + goto nomem; + b->size = size; + memcpy(b->data, atags_copy, size); + + tags_entry = create_proc_read_entry("atags", 0400, + NULL, read_buffer, b); + + if (!tags_entry) + goto nomem; + + return 0; + +nomem: + kfree(b); + printk(KERN_ERR "Exporting ATAGs: not enough memory\n"); + + return -ENOMEM; +} arch_initcall(init_atags_procfs); -- cgit v1.2.3 From a4831fbe096a6f4f691fd71b041ce27add54088e Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Wed, 21 May 2008 10:17:07 +0200 Subject: ns9xxx: fix assembler version of __REG2 to be consistent with the C version MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit It's not very critical because __REG2 isn't used in assembler code currently. Additionally some white space noise is fixed. Signed-off-by: Uwe Kleine-König --- include/asm-arm/arch-ns9xxx/hardware.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/include/asm-arm/arch-ns9xxx/hardware.h b/include/asm-arm/arch-ns9xxx/hardware.h index 0b7b34603f1c..0dca11ce21fc 100644 --- a/include/asm-arm/arch-ns9xxx/hardware.h +++ b/include/asm-arm/arch-ns9xxx/hardware.h @@ -66,13 +66,13 @@ __REGGET(var, reg ## _ ## field) / __REGSHIFT(reg ## _ ## field) # define REGGETIM_IDX(var, reg, field, idx) \ - __REGGET(var, reg ## _ ## field((idx))) / \ + __REGGET(var, reg ## _ ## field((idx))) / \ __REGSHIFT(reg ## _ ## field((idx))) #else # define __REG(x) io_p2v(x) -# define __REG2(x, y) io_p2v((x) + (y)) +# define __REG2(x, y) io_p2v((x) + 4 * (y)) #endif -- cgit v1.2.3 From 1a7e612fa5ea0311232bd5418a40ec7280557789 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sat, 31 May 2008 16:18:11 +0100 Subject: [ARM] 5074/1: fix warning: missing terminating ' character Signed-off-by: Dmitry Baryshkov Acked-by: Richard Purdie Signed-off-by: Russell King --- include/asm-arm/arch-pxa/pxa27x-udc.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/asm-arm/arch-pxa/pxa27x-udc.h b/include/asm-arm/arch-pxa/pxa27x-udc.h index 9cf0b1f88112..2d4e9cd3a5e3 100644 --- a/include/asm-arm/arch-pxa/pxa27x-udc.h +++ b/include/asm-arm/arch-pxa/pxa27x-udc.h @@ -2,7 +2,7 @@ #define _ASM_ARCH_PXA27X_UDC_H #ifdef _ASM_ARCH_PXA25X_UDC_H -#error You can't include both PXA25x and PXA27x UDC support +#error You cannot include both PXA25x and PXA27x UDC support #endif #define UDCCR __REG(0x40600000) /* UDC Control Register */ -- cgit v1.2.3 From 720046de27ec2a96d4497dbca8ee98657efa059c Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 24 Apr 2008 15:13:36 +0100 Subject: [ARM] pxa: don't register lpd270 cpld_irq sysdev if !lpd270 Don't register the LPD270 cpld_irq system device when we're not running on a LPD270 machine - "cpld_irq" is also registered (separately) by Lubbock and Mainstone. Signed-off-by: Russell King --- arch/arm/mach-pxa/lpd270.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c index a20e4b1649d6..6fd7b8b753fc 100644 --- a/arch/arm/mach-pxa/lpd270.c +++ b/arch/arm/mach-pxa/lpd270.c @@ -134,9 +134,12 @@ static struct sys_device lpd270_irq_device = { static int __init lpd270_irq_device_init(void) { - int ret = sysdev_class_register(&lpd270_irq_sysclass); - if (ret == 0) - ret = sysdev_register(&lpd270_irq_device); + int ret = -ENODEV; + if (machine_is_logicpd_pxa270()) { + ret = sysdev_class_register(&lpd270_irq_sysclass); + if (ret == 0) + ret = sysdev_register(&lpd270_irq_device); + } return ret; } -- cgit v1.2.3 From 04ba0f656f7580d8a51a5b3441e088309141b67a Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 24 Apr 2008 15:23:25 +0100 Subject: [ARM] pxa: avoid registering multiple pxa2xx_pcmcia devices cm_x270 and mainstone both register their PCMCIA devices using the same name, resulting in a warning message from the kernel. Avoid this by making the cm_x270 and mainstone PCMCIA initialisation conditional on the machine type we're running on. Signed-off-by: Russell King --- drivers/pcmcia/pxa2xx_cm_x270.c | 4 ++++ drivers/pcmcia/pxa2xx_mainstone.c | 4 ++++ 2 files changed, 8 insertions(+) diff --git a/drivers/pcmcia/pxa2xx_cm_x270.c b/drivers/pcmcia/pxa2xx_cm_x270.c index e7ab060ff118..4a6c020afb37 100644 --- a/drivers/pcmcia/pxa2xx_cm_x270.c +++ b/drivers/pcmcia/pxa2xx_cm_x270.c @@ -18,6 +18,7 @@ #include #include +#include #include #include @@ -147,6 +148,9 @@ static int __init cmx270_pcmcia_init(void) { int ret; + if (!machine_is_armcore()) + return -ENODEV; + cmx270_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1); if (!cmx270_pcmcia_device) diff --git a/drivers/pcmcia/pxa2xx_mainstone.c b/drivers/pcmcia/pxa2xx_mainstone.c index 145b85e0f02c..36a59960b5af 100644 --- a/drivers/pcmcia/pxa2xx_mainstone.c +++ b/drivers/pcmcia/pxa2xx_mainstone.c @@ -22,6 +22,7 @@ #include #include +#include #include #include @@ -153,6 +154,9 @@ static int __init mst_pcmcia_init(void) { int ret; + if (!machine_is_mainstone()) + return -ENODEV; + mst_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1); if (!mst_pcmcia_device) return -ENOMEM; -- cgit v1.2.3 From 4e5e8de0dbdeb08df2b4c15fa2b0ba2216091793 Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 24 Apr 2008 15:28:11 +0100 Subject: [ARM] pxa: avoid kfreeing static data if platform device fails to register When a dynamically allocated platform device is 'put', the platform device's platform_data is kfree'd. This is bad if it's pointing at static data. Use the provided function to register platform data for these devices. This also means we can mark the pcmcia ops structures as __initdata. Signed-off-by: Russell King --- drivers/pcmcia/pxa2xx_cm_x270.c | 11 +++++++---- drivers/pcmcia/pxa2xx_mainstone.c | 9 +++++---- drivers/pcmcia/pxa2xx_sharpsl.c | 12 +++++++----- 3 files changed, 19 insertions(+), 13 deletions(-) diff --git a/drivers/pcmcia/pxa2xx_cm_x270.c b/drivers/pcmcia/pxa2xx_cm_x270.c index 4a6c020afb37..f123fce65f2e 100644 --- a/drivers/pcmcia/pxa2xx_cm_x270.c +++ b/drivers/pcmcia/pxa2xx_cm_x270.c @@ -131,7 +131,7 @@ static void cmx270_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt) } -static struct pcmcia_low_level cmx270_pcmcia_ops = { +static struct pcmcia_low_level cmx270_pcmcia_ops __initdata = { .owner = THIS_MODULE, .hw_init = cmx270_pcmcia_hw_init, .hw_shutdown = cmx270_pcmcia_shutdown, @@ -156,10 +156,13 @@ static int __init cmx270_pcmcia_init(void) if (!cmx270_pcmcia_device) return -ENOMEM; - cmx270_pcmcia_device->dev.platform_data = &cmx270_pcmcia_ops; + ret = platform_device_add_data(cmx270_pcmcia_device, &cmx270_pcmcia_ops, + sizeof(cmx270_pcmcia_ops)); - printk(KERN_INFO "Registering cm-x270 PCMCIA interface.\n"); - ret = platform_device_add(cmx270_pcmcia_device); + if (ret == 0) { + printk(KERN_INFO "Registering cm-x270 PCMCIA interface.\n"); + ret = platform_device_add(cmx270_pcmcia_device); + } if (ret) platform_device_put(cmx270_pcmcia_device); diff --git a/drivers/pcmcia/pxa2xx_mainstone.c b/drivers/pcmcia/pxa2xx_mainstone.c index 36a59960b5af..92d1cc33808c 100644 --- a/drivers/pcmcia/pxa2xx_mainstone.c +++ b/drivers/pcmcia/pxa2xx_mainstone.c @@ -137,7 +137,7 @@ static void mst_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt) { } -static struct pcmcia_low_level mst_pcmcia_ops = { +static struct pcmcia_low_level mst_pcmcia_ops __initdata = { .owner = THIS_MODULE, .hw_init = mst_pcmcia_hw_init, .hw_shutdown = mst_pcmcia_hw_shutdown, @@ -161,9 +161,10 @@ static int __init mst_pcmcia_init(void) if (!mst_pcmcia_device) return -ENOMEM; - mst_pcmcia_device->dev.platform_data = &mst_pcmcia_ops; - - ret = platform_device_add(mst_pcmcia_device); + ret = platform_device_add_data(mst_pcmcia_device, &mst_pcmcia_ops, + sizeof(mst_pcmcia_ops)); + if (ret == 0) + ret = platform_device_add(mst_pcmcia_device); if (ret) platform_device_put(mst_pcmcia_device); diff --git a/drivers/pcmcia/pxa2xx_sharpsl.c b/drivers/pcmcia/pxa2xx_sharpsl.c index d5c33bd78d68..d71f93d45833 100644 --- a/drivers/pcmcia/pxa2xx_sharpsl.c +++ b/drivers/pcmcia/pxa2xx_sharpsl.c @@ -222,7 +222,7 @@ static void sharpsl_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt) sharpsl_pcmcia_init_reset(skt); } -static struct pcmcia_low_level sharpsl_pcmcia_ops = { +static struct pcmcia_low_level sharpsl_pcmcia_ops __initdata = { .owner = THIS_MODULE, .hw_init = sharpsl_pcmcia_hw_init, .hw_shutdown = sharpsl_pcmcia_hw_shutdown, @@ -261,10 +261,12 @@ static int __init sharpsl_pcmcia_init(void) if (!sharpsl_pcmcia_device) return -ENOMEM; - sharpsl_pcmcia_device->dev.platform_data = &sharpsl_pcmcia_ops; - sharpsl_pcmcia_device->dev.parent = platform_scoop_config->devs[0].dev; - - ret = platform_device_add(sharpsl_pcmcia_device); + ret = platform_device_add_data(sharpsl_pcmcia_device, + &sharpsl_pcmcia_ops, sizeof(sharpsl_pcmcia_ops)); + if (ret == 0) { + sharpsl_pcmcia_device->dev.parent = platform_scoop_config->devs[0].dev; + ret = platform_device_add(sharpsl_pcmcia_device); + } if (ret) platform_device_put(sharpsl_pcmcia_device); -- cgit v1.2.3 From ffdf786291636137ef2d51c3a5d340793032aa28 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 18 May 2008 14:57:59 +0100 Subject: [ARM] pxa: Add PXA3_ prefix to PXA3 specific constants standby.S contains both PXA2 and PXA3 specific code. The PXA3 specific constants clash with the PXA2 ones, so give them a prefix. Signed-off-by: Russell King --- arch/arm/mach-pxa/standby.S | 82 ++++++++++++++++++++++----------------------- 1 file changed, 41 insertions(+), 41 deletions(-) diff --git a/arch/arm/mach-pxa/standby.S b/arch/arm/mach-pxa/standby.S index 167412e6bec8..a37ef1c4b9e9 100644 --- a/arch/arm/mach-pxa/standby.S +++ b/arch/arm/mach-pxa/standby.S @@ -35,20 +35,20 @@ ENTRY(pxa_cpu_standby) #ifdef CONFIG_PXA3xx -#define MDCNFG 0x0000 -#define MDCNFG_DMCEN (1 << 30) -#define DDR_HCAL 0x0060 -#define DDR_HCAL_HCRNG 0x1f -#define DDR_HCAL_HCPROG (1 << 28) -#define DDR_HCAL_HCEN (1 << 31) -#define DMCIER 0x0070 -#define DMCIER_EDLP (1 << 29) -#define DMCISR 0x0078 -#define RCOMP 0x0100 -#define RCOMP_SWEVAL (1 << 31) +#define PXA3_MDCNFG 0x0000 +#define PXA3_MDCNFG_DMCEN (1 << 30) +#define PXA3_DDR_HCAL 0x0060 +#define PXA3_DDR_HCAL_HCRNG 0x1f +#define PXA3_DDR_HCAL_HCPROG (1 << 28) +#define PXA3_DDR_HCAL_HCEN (1 << 31) +#define PXA3_DMCIER 0x0070 +#define PXA3_DMCIER_EDLP (1 << 29) +#define PXA3_DMCISR 0x0078 +#define PXA3_RCOMP 0x0100 +#define PXA3_RCOMP_SWEVAL (1 << 31) ENTRY(pm_enter_standby_start) - mov r1, #0xf6000000 @ DMEMC_REG_BASE (MDCNFG) + mov r1, #0xf6000000 @ DMEMC_REG_BASE (PXA3_MDCNFG) add r1, r1, #0x00100000 /* @@ -59,54 +59,54 @@ ENTRY(pm_enter_standby_start) * This also means that only the dynamic memory controller * can be reliably accessed in the code following standby. */ - ldr r2, [r1] @ Dummy read MDCNFG + ldr r2, [r1] @ Dummy read PXA3_MDCNFG mcr p14, 0, r0, c7, c0, 0 .rept 8 nop .endr - ldr r0, [r1, #DDR_HCAL] @ Clear (and wait for) HCEN - bic r0, r0, #DDR_HCAL_HCEN - str r0, [r1, #DDR_HCAL] -1: ldr r0, [r1, #DDR_HCAL] - tst r0, #DDR_HCAL_HCEN + ldr r0, [r1, #PXA3_DDR_HCAL] @ Clear (and wait for) HCEN + bic r0, r0, #PXA3_DDR_HCAL_HCEN + str r0, [r1, #PXA3_DDR_HCAL] +1: ldr r0, [r1, #PXA3_DDR_HCAL] + tst r0, #PXA3_DDR_HCAL_HCEN bne 1b - ldr r0, [r1, #RCOMP] @ Initiate RCOMP - orr r0, r0, #RCOMP_SWEVAL - str r0, [r1, #RCOMP] + ldr r0, [r1, #PXA3_RCOMP] @ Initiate RCOMP + orr r0, r0, #PXA3_RCOMP_SWEVAL + str r0, [r1, #PXA3_RCOMP] - mov r0, #~0 @ Clear interrupts - str r0, [r1, #DMCISR] + mov r0, #~0 @ Clear interrupts + str r0, [r1, #PXA3_DMCISR] - ldr r0, [r1, #DMCIER] @ set DMIER[EDLP] - orr r0, r0, #DMCIER_EDLP - str r0, [r1, #DMCIER] + ldr r0, [r1, #PXA3_DMCIER] @ set DMIER[EDLP] + orr r0, r0, #PXA3_DMCIER_EDLP + str r0, [r1, #PXA3_DMCIER] - ldr r0, [r1, #DDR_HCAL] @ clear HCRNG, set HCPROG, HCEN - bic r0, r0, #DDR_HCAL_HCRNG - orr r0, r0, #DDR_HCAL_HCEN | DDR_HCAL_HCPROG - str r0, [r1, #DDR_HCAL] + ldr r0, [r1, #PXA3_DDR_HCAL] @ clear HCRNG, set HCPROG, HCEN + bic r0, r0, #PXA3_DDR_HCAL_HCRNG + orr r0, r0, #PXA3_DDR_HCAL_HCEN | PXA3_DDR_HCAL_HCPROG + str r0, [r1, #PXA3_DDR_HCAL] -1: ldr r0, [r1, #DMCISR] - tst r0, #DMCIER_EDLP +1: ldr r0, [r1, #PXA3_DMCISR] + tst r0, #PXA3_DMCIER_EDLP beq 1b - ldr r0, [r1, #MDCNFG] @ set MDCNFG[DMCEN] - orr r0, r0, #MDCNFG_DMCEN - str r0, [r1, #MDCNFG] -1: ldr r0, [r1, #MDCNFG] - tst r0, #MDCNFG_DMCEN + ldr r0, [r1, #PXA3_MDCNFG] @ set PXA3_MDCNFG[DMCEN] + orr r0, r0, #PXA3_MDCNFG_DMCEN + str r0, [r1, #PXA3_MDCNFG] +1: ldr r0, [r1, #PXA3_MDCNFG] + tst r0, #PXA3_MDCNFG_DMCEN beq 1b - ldr r0, [r1, #DDR_HCAL] @ set DDR_HCAL[HCRNG] + ldr r0, [r1, #PXA3_DDR_HCAL] @ set PXA3_DDR_HCAL[HCRNG] orr r0, r0, #2 @ HCRNG - str r0, [r1, #DDR_HCAL] + str r0, [r1, #PXA3_DDR_HCAL] - ldr r0, [r1, #DMCIER] @ Clear the interrupt + ldr r0, [r1, #PXA3_DMCIER] @ Clear the interrupt bic r0, r0, #0x20000000 - str r0, [r1, #DMCIER] + str r0, [r1, #PXA3_DMCIER] mov pc, lr ENTRY(pm_enter_standby_end) -- cgit v1.2.3 From e3ba22db09408baee721897fb1b50e16f071d916 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Sat, 24 May 2008 17:06:45 +0100 Subject: [ARM] 5056/1: [AT91] Cleanup YL9200 board file Cleanup the YL9200 board-support file. Other things fixed are: - Use new-style UART initialization - Register all LEDs as gpio_leds. - NOR Flash error noted in comments fixed by increasing YL9200_FLASH_SIZE - The only I2C device is the AT24C eeprom. - Setup of NWAIT pin and programming of SMC controller for the LCD/VGA. - Configure touchscreen interrupt pin. Also adding the board to the KConfig and Makefile. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/Kconfig | 6 + arch/arm/mach-at91/Makefile | 1 + arch/arm/mach-at91/board-yl-9200.c | 853 +++++++++++++++++-------------------- 3 files changed, 394 insertions(+), 466 deletions(-) diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 0fc07b6db749..3d549a9afe1d 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -126,6 +126,12 @@ config MACH_ECBAT91 Select this if you are using emQbit's ECB_AT91 board. +config MACH_YL9200 + bool "ucDragon YL-9200" + depends on ARCH_AT91RM9200 + help + Select this if you are using the ucDragon YL-9200 board. + endif # ---------------------------------------------------------- diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 8d9bc0153b18..995be14b2c42 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -30,6 +30,7 @@ obj-$(CONFIG_MACH_ATEB9200) += board-eb9200.o obj-$(CONFIG_MACH_KAFA) += board-kafa.o obj-$(CONFIG_MACH_PICOTUX2XX) += board-picotux200.o obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o +obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o # AT91SAM9260 board-specific support obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index b5717108991d..7079050ab88d 100755 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -1,11 +1,10 @@ /* * linux/arch/arm/mach-at91/board-yl-9200.c * - * Adapted from: - *various board files in - * /arch/arm/mach-at91 - * modifications to convert to YL-9200 platform - * Copyright (C) 2007 S.Birtles + * Adapted from various board files in arch/arm/mach-at91 + * + * Modifications for YL-9200 platform: + * Copyright (C) 2007 S. Birtles * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -26,13 +25,14 @@ #include #include #include +#include #include #include -/*#include */ #include #include +#include +#include -/*#include */ #include #include #include @@ -45,179 +45,108 @@ #include #include #include -#include -#include #include "generic.h" -#include -#define YL_9200_FLASH_BASE AT91_CHIPSELECT_0 -#define YL_9200_FLASH_SIZE 0x800000 -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - *atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL - *atmel_usart.1: ttyS1 at MMIO 0xfffc0000 (irq = 6) is a ATMEL_SERIAL - *atmel_usart.2: ttyS2 at MMIO 0xfffc4000 (irq = 7) is a ATMEL_SERIAL - *atmel_usart.3: ttyS3 at MMIO 0xfffc8000 (irq = 8) is a ATMEL_SERIAL - *atmel_usart.4: ttyS4 at MMIO 0xfffcc000 (irq = 9) is a ATMEL_SERIAL - * on the YL-9200 we are sitting at the following - *ttyS0 at MMIO 0xfefff200 (irq = 1) is a AT91_SERIAL - *ttyS1 at MMIO 0xfefc4000 (irq = 7) is a AT91_SERIAL - */ +static void __init yl9200_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91rm9200_initialize(18432000, AT91RM9200_PQFP); -/* extern void __init yl_9200_add_device_sounder(struct gpio_sounder *sounders, int nr);*/ + /* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */ + at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17); -static struct at91_uart_config __initdata yl_9200_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 3, - .tty_map = { 4, 1, 0, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); -static void __init yl_9200_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - /*Also initialises register clocks & gpio*/ - at91rm9200_initialize(18432000, AT91RM9200_PQFP); /*we have a 3 bank system*/ + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); - /* Setup the serial ports and console */ - at91_init_serial(&yl_9200_uart_config); + /* USART0 on ttyS2. (Rx & Tx only to JP3) */ + at91_register_uart(AT91RM9200_ID_US0, 2, 0); - /* Setup the LEDs D2=PB17,D3=PB16 */ - at91_init_leds(AT91_PIN_PB16,AT91_PIN_PB17); /*cpu-led,timer-led*/ + /* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */ + at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); } -static void __init yl_9200_init_irq(void) +static void __init yl9200_init_irq(void) { at91rm9200_init_interrupts(NULL); } -static struct at91_eth_data __initdata yl_9200_eth_data = { - .phy_irq_pin = AT91_PIN_PB28, - .is_rmii = 1, -}; -static struct at91_usbh_data __initdata yl_9200_usbh_data = { - .ports = 1, /* this should be 1 not 2 for the Yl9200*/ +/* + * LEDs + */ +static struct gpio_led yl9200_leds[] = { + { /* D2 */ + .name = "led2", + .gpio = AT91_PIN_PB17, + .active_low = 1, + .default_trigger = "timer", + }, + { /* D3 */ + .name = "led3", + .gpio = AT91_PIN_PB16, + .active_low = 1, + .default_trigger = "heartbeat", + }, + { /* D4 */ + .name = "led4", + .gpio = AT91_PIN_PB15, + .active_low = 1, + }, + { /* D5 */ + .name = "led5", + .gpio = AT91_PIN_PB8, + .active_low = 1, + } }; -static struct at91_udc_data __initdata yl_9200_udc_data = { -/*on sheet 7 Schemitic rev 1.0*/ - .pullup_pin = AT91_PIN_PC4, - .vbus_pin= AT91_PIN_PC5, - .pullup_active_low = 1, /*ACTIVE LOW!! due to PNP transistor on page 7*/ - -}; /* -static struct at91_cf_data __initdata yl_9200_cf_data = { -TODO S.BIRTLES - .det_pin = AT91_PIN_xxx, - .rst_pin = AT91_PIN_xxx, - .irq_pin = ... not connected - .vcc_pin = ... always powered - + * Ethernet + */ +static struct at91_eth_data __initdata yl9200_eth_data = { + .phy_irq_pin = AT91_PIN_PB28, + .is_rmii = 1, }; -*/ -static struct at91_mmc_data __initdata yl_9200_mmc_data = { - .det_pin = AT91_PIN_PB9, /*THIS LOOKS CORRECT SHEET7*/ -/* .wp_pin = ... not connected SHEET7*/ - .slot_b = 0, - .wire4 = 1, +/* + * USB Host + */ +static struct at91_usbh_data __initdata yl9200_usbh_data = { + .ports = 1, /* PQFP version of AT91RM9200 */ }; -/* -------------------------------------------------------------------- - * Touch screen - * -------------------------------------------------------------------- */ -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) -static int ads7843_pendown_state(void) -{ - return !at91_get_gpio_value(AT91_PIN_PB11); /* Touchscreen PENIRQ */ -} - -static void __init at91_init_device_ts(void) -{ -/*IMPORTANT NOTE THE SPI INTERFACE IS ALREADY CONFIGURED BY XXX_DEVICES.C -THAT IS TO SAY THAT MISO,MOSI,SPCK AND CS are already configured -we only need to enable the other datapins which are: -PB10/RK1 BUSY -*/ -/* Touchscreen BUSY signal , pin,use pullup ( TODO not currently used in the ADS7843/6.c driver)*/ -at91_set_gpio_input(AT91_PIN_PB10, 1); -} - -#else -static void __init at91_init_device_ts(void) {} -#endif - -static struct ads7846_platform_data ads_info = { - .model = 7843, - .x_min = 150, - .x_max = 3830, - .y_min = 190, - .y_max = 3830, - .vref_delay_usecs = 100, -/* for a 8" touch screen*/ - //.x_plate_ohms = 603, //= 450, S.Birtles TODO - //.y_plate_ohms = 332, //= 250, S.Birtles TODO -/*for a 10.4" touch screen*/ - //.x_plate_ohms =611, - //.y_plate_ohms =325, - - .x_plate_ohms = 576, - .y_plate_ohms = 366, - // - .pressure_max = 15000, /*generally nonsense on the 7843*/ - /*number of times to send query to chip in a given run 0 equals one time (do not set to 0!! ,there is a bug in ADS 7846 code)*/ - .debounce_max = 1, - .debounce_rep = 0, - .debounce_tol = (~0), - .get_pendown_state = ads7843_pendown_state, -}; +/* + * USB Device + */ +static struct at91_udc_data __initdata yl9200_udc_data = { + .pullup_pin = AT91_PIN_PC4, + .vbus_pin = AT91_PIN_PC5, + .pullup_active_low = 1, /* Active Low due to PNP transistor (pg 7) */ -/*static struct canbus_platform_data can_info = { - .model = 2510, }; -*/ - -static struct spi_board_info yl_9200_spi_devices[] = { -/*this sticks it at: - /sys/devices/platform/atmel_spi.0/spi0.0 - /sys/bus/platform/devices/ -Documentation/spi IIRC*/ -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) - /*(this IS correct 04-NOV-2007)*/ - { - .modalias = "ads7846", /* because the driver is called ads7846*/ - .chip_select = 0, /*THIS MUST BE AN INDEX INTO AN ARRAY OF pins */ -/*this is ONLY TO BE USED if chipselect above is not used, it passes a pin directly for the chip select*/ - /*.controller_data =AT91_PIN_PA3 ,*/ - .max_speed_hz = 5000*26, /*(4700 * 26)-125000 * 26, (max sample rate @ 3V) * (cmd + data + overhead) */ - .bus_num = 0, - .platform_data = &ads_info, - .irq = AT91_PIN_PB11, - }, -#endif -/*we need to put our CAN driver data here!!*/ -/*THIS IS ALL DUMMY DATA*/ -/* { - .modalias = "mcp2510", //DUMMY for MCP2510 chip - .chip_select = 1,*/ /*THIS MUST BE AN INDEX INTO AN ARRAY OF pins */ - /*this is ONLY TO BE USED if chipselect above is not used, it passes a pin directly for the chip select */ - /* .controller_data =AT91_PIN_PA4 , - .max_speed_hz = 25000 * 26, - .bus_num = 0, - .platform_data = &can_info, - .irq = AT91_PIN_PC0, - }, - */ - //max SPI chip needs to go here +/* + * MMC + */ +static struct at91_mmc_data __initdata yl9200_mmc_data = { + .det_pin = AT91_PIN_PB9, + // .wp_pin = ... not connected + .wire4 = 1, }; -static struct mtd_partition __initdata yl_9200_nand_partition[] = { +/* + * NAND Flash + */ +static struct mtd_partition __initdata yl9200_nand_partition[] = { { .name = "AT91 NAND partition 1, boot", .offset = 0, @@ -242,442 +171,434 @@ static struct mtd_partition __initdata yl_9200_nand_partition[] = { .name = "AT91 NAND partition 5, ext-fs", .offset = 32 * SZ_1M, .size = 32 * SZ_1M - }, + } }; static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) { - *num_partitions = ARRAY_SIZE(yl_9200_nand_partition); - return yl_9200_nand_partition; + *num_partitions = ARRAY_SIZE(yl9200_nand_partition); + return yl9200_nand_partition; } -static struct at91_nand_data __initdata yl_9200_nand_data = { - .ale= 6, - .cle= 7, - /*.det_pin = AT91_PIN_PCxx,*/ /*we don't have a det pin because NandFlash is fixed to board*/ - .rdy_pin = AT91_PIN_PC14, /*R/!B Sheet10*/ - .enable_pin = AT91_PIN_PC15, /*!CE Sheet10 */ +static struct at91_nand_data __initdata yl9200_nand_data = { + .ale = 6, + .cle = 7, + // .det_pin = ... not connected + .rdy_pin = AT91_PIN_PC14, /* R/!B (Sheet10) */ + .enable_pin = AT91_PIN_PC15, /* !CE (Sheet10) */ .partition_info = nand_partitions, }; - - /* -TODO S.Birtles -potentially a problem with the size above -physmap platform flash device: 00800000 at 10000000 -physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank -NOR chip too large to fit in mapping. Attempting to cope... - Intel/Sharp Extended Query Table at 0x0031 -Using buffer write method -cfi_cmdset_0001: Erase suspend on write enabled -Reducing visibility of 16384KiB chip to 8192KiB -*/ + * NOR Flash + */ +#define YL9200_FLASH_BASE AT91_CHIPSELECT_0 +#define YL9200_FLASH_SIZE 0x1000000 -static struct mtd_partition yl_9200_flash_partitions[] = { +static struct mtd_partition yl9200_flash_partitions[] = { + { + .name = "Bootloader", + .size = 0x00040000, + .offset = 0, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, { - .name = "Bootloader", - .size = 0x00040000, - .offset = 0, - .mask_flags = MTD_WRITEABLE /* force read-only */ - },{ - .name = "Kernel", - .size = 0x001C0000, - .offset = 0x00040000, - },{ - .name = "Filesystem", - .size = MTDPART_SIZ_FULL, - .offset = 0x00200000 + .name = "Kernel", + .size = 0x001C0000, + .offset = 0x00040000, + }, + { + .name = "Filesystem", + .size = MTDPART_SIZ_FULL, + .offset = 0x00200000 } - }; -static struct physmap_flash_data yl_9200_flash_data = { - .width = 2, - .parts = yl_9200_flash_partitions, - .nr_parts = ARRAY_SIZE(yl_9200_flash_partitions), +static struct physmap_flash_data yl9200_flash_data = { + .width = 2, + .parts = yl9200_flash_partitions, + .nr_parts = ARRAY_SIZE(yl9200_flash_partitions), }; -static struct resource yl_9200_flash_resources[] = { -{ - .start = YL_9200_FLASH_BASE, - .end = YL_9200_FLASH_BASE + YL_9200_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, +static struct resource yl9200_flash_resources[] = { + { + .start = YL9200_FLASH_BASE, + .end = YL9200_FLASH_BASE + YL9200_FLASH_SIZE - 1, + .flags = IORESOURCE_MEM, } }; -static struct platform_device yl_9200_flash = { +static struct platform_device yl9200_flash = { .name = "physmap-flash", .id = 0, .dev = { - .platform_data = &yl_9200_flash_data, + .platform_data = &yl9200_flash_data, }, - .resource = yl_9200_flash_resources, - .num_resources = ARRAY_SIZE(yl_9200_flash_resources), + .resource = yl9200_flash_resources, + .num_resources = ARRAY_SIZE(yl9200_flash_resources), }; - -static struct gpio_led yl_9200_leds[] = { -/*D2 &D3 are passed directly in via at91_init_leds*/ - { - .name = "led4", /*D4*/ - .gpio = AT91_PIN_PB15, - .active_low = 1, - .default_trigger = "heartbeat", - /*.default_trigger = "timer",*/ - }, - { - .name = "led5", /*D5*/ - .gpio = AT91_PIN_PB8, - .active_low = 1, - .default_trigger = "heartbeat", - } -}; - -//static struct gpio_sounder yl_9200_sounder[] = {*/ -/*This is a simple speaker attached to a gpo line*/ - -// { -// .name = "Speaker", /*LS1*/ -// .gpio = AT91_PIN_PA22, -// .active_low = 0, -// .default_trigger = "heartbeat", - /*.default_trigger = "timer",*/ -// }, -//}; - - - -static struct i2c_board_info __initdata yl_9200_i2c_devices[] = { - { - /*TODO*/ - I2C_BOARD_INFO("CS4334", 0x00), +/* + * I2C (TWI) + */ +static struct i2c_board_info __initdata yl9200_i2c_devices[] = { + { /* EEPROM */ + I2C_BOARD_INFO("24c128", 0x50), } }; - - /* +/* * GPIO Buttons - */ +*/ #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -static struct gpio_keys_button yl_9200_buttons[] = { +static struct gpio_keys_button yl9200_buttons[] = { { .gpio = AT91_PIN_PA24, - .code = BTN_2, + .code = BTN_2, .desc = "SW2", .active_low = 1, .wakeup = 1, }, { .gpio = AT91_PIN_PB1, - .code = BTN_3, + .code = BTN_3, .desc = "SW3", .active_low = 1, .wakeup = 1, }, { .gpio = AT91_PIN_PB2, - .code = BTN_4, + .code = BTN_4, .desc = "SW4", .active_low = 1, .wakeup = 1, }, { .gpio = AT91_PIN_PB6, - .code = BTN_5, + .code = BTN_5, .desc = "SW5", .active_low = 1, .wakeup = 1, - }, - + } }; -static struct gpio_keys_platform_data yl_9200_button_data = { - .buttons = yl_9200_buttons, - .nbuttons = ARRAY_SIZE(yl_9200_buttons), +static struct gpio_keys_platform_data yl9200_button_data = { + .buttons = yl9200_buttons, + .nbuttons = ARRAY_SIZE(yl9200_buttons), }; -static struct platform_device yl_9200_button_device = { +static struct platform_device yl9200_button_device = { .name = "gpio-keys", .id = -1, .num_resources = 0, .dev = { - .platform_data = &yl_9200_button_data, + .platform_data = &yl9200_button_data, } }; -static void __init yl_9200_add_device_buttons(void) +static void __init yl9200_add_device_buttons(void) { - //SW2 - at91_set_gpio_input(AT91_PIN_PA24, 0); + at91_set_gpio_input(AT91_PIN_PA24, 1); /* SW2 */ at91_set_deglitch(AT91_PIN_PA24, 1); - - //SW3 - at91_set_gpio_input(AT91_PIN_PB1, 0); + at91_set_gpio_input(AT91_PIN_PB1, 1); /* SW3 */ at91_set_deglitch(AT91_PIN_PB1, 1); - //SW4 - at91_set_gpio_input(AT91_PIN_PB2, 0); + at91_set_gpio_input(AT91_PIN_PB2, 1); /* SW4 */ at91_set_deglitch(AT91_PIN_PB2, 1); - - //SW5 - at91_set_gpio_input(AT91_PIN_PB6, 0); + at91_set_gpio_input(AT91_PIN_PB6, 1); /* SW5 */ at91_set_deglitch(AT91_PIN_PB6, 1); + /* Enable buttons (Sheet 5) */ + at91_set_gpio_output(AT91_PIN_PB7, 1); + + platform_device_register(&yl9200_button_device); +} +#else +static void __init yl9200_add_device_buttons(void) {} +#endif + +/* + * Touchscreen + */ +#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) +static int ads7843_pendown_state(void) +{ + return !at91_get_gpio_value(AT91_PIN_PB11); /* Touchscreen PENIRQ */ +} + +static struct ads7846_platform_data ads_info = { + .model = 7843, + .x_min = 150, + .x_max = 3830, + .y_min = 190, + .y_max = 3830, + .vref_delay_usecs = 100, + + /* For a 8" touch-screen */ + // .x_plate_ohms = 603, + // .y_plate_ohms = 332, + + /* For a 10.4" touch-screen */ + // .x_plate_ohms = 611, + // .y_plate_ohms = 325, + + .x_plate_ohms = 576, + .y_plate_ohms = 366, + + .pressure_max = 15000, /* generally nonsense on the 7843 */ + .debounce_max = 1, + .debounce_rep = 0, + .debounce_tol = (~0), + .get_pendown_state = ads7843_pendown_state, +}; - at91_set_gpio_output(AT91_PIN_PB7, 1); /* #TURN BUTTONS ON, SHEET 5 of schematics */ - platform_device_register(&yl_9200_button_device); +static void __init yl9200_add_device_ts(void) +{ + at91_set_gpio_input(AT91_PIN_PB11, 1); /* Touchscreen interrupt pin */ + at91_set_gpio_input(AT91_PIN_PB10, 1); /* Touchscreen BUSY signal - not used! */ } #else -static void __init yl_9200_add_device_buttons(void) {} +static void __init yl9200_add_device_ts(void) {} +#endif + +/* + * SPI devices + */ +static struct spi_board_info yl9200_spi_devices[] = { +#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) + { /* Touchscreen */ + .modalias = "ads7846", + .chip_select = 0, + .max_speed_hz = 5000 * 26, + .platform_data = &ads_info, + .irq = AT91_PIN_PB11, + }, #endif + { /* CAN */ + .modalias = "mcp2510", + .chip_select = 1, + .max_speed_hz = 25000 * 26, + .irq = AT91_PIN_PC0, + } +}; +/* + * LCD / VGA + * + * EPSON S1D13806 FB (discontinued chip) + * EPSON S1D13506 FB + */ #if defined(CONFIG_FB_S1D135XX) || defined(CONFIG_FB_S1D13XXX_MODULE) #include