From 3c76f6119a64eb8ff6d088ceb6ca03891e29a7ce Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 5 Aug 2015 17:01:54 +0300 Subject: memory: omap-gpmc: Move device tree binding to correct location omap-gpmc.c is a memory controller so move the binding to the right place. Signed-off-by: Roger Quadros Acked-by: Rob Herring Acked-by: Tony Lindgren --- Documentation/devicetree/bindings/bus/ti-gpmc.txt | 143 ---------------------- 1 file changed, 143 deletions(-) delete mode 100644 Documentation/devicetree/bindings/bus/ti-gpmc.txt (limited to 'Documentation/devicetree/bindings/bus') diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt deleted file mode 100644 index 13f13786f992..000000000000 --- a/Documentation/devicetree/bindings/bus/ti-gpmc.txt +++ /dev/null @@ -1,143 +0,0 @@ -Device tree bindings for OMAP general purpose memory controllers (GPMC) - -The actual devices are instantiated from the child nodes of a GPMC node. - -Required properties: - - - compatible: Should be set to one of the following: - - ti,omap2420-gpmc (omap2420) - ti,omap2430-gpmc (omap2430) - ti,omap3430-gpmc (omap3430 & omap3630) - ti,omap4430-gpmc (omap4430 & omap4460 & omap543x) - ti,am3352-gpmc (am335x devices) - - - reg: A resource specifier for the register space - (see the example below) - - ti,hwmods: Should be set to "ti,gpmc" until the DT transition is - completed. - - #address-cells: Must be set to 2 to allow memory address translation - - #size-cells: Must be set to 1 to allow CS address passing - - gpmc,num-cs: The maximum number of chip-select lines that controller - can support. - - gpmc,num-waitpins: The maximum number of wait pins that controller can - support. - - ranges: Must be set up to reflect the memory layout with four - integer values for each chip-select line in use: - - 0 - - Currently, calculated values derived from the contents - of the per-CS register GPMC_CONFIG7 (as set up by the - bootloader) are used for the physical address decoding. - As this will change in the future, filling correct - values here is a requirement. - - interrupt-controller: The GPMC driver implements and interrupt controller for - the NAND events "fifoevent" and "termcount". - The interrupt number mapping is as follows - 0 - NAND_fifoevent - 1 - NAND_termcount - - interrupt-cells: Must be set to 2 - -Timing properties for child nodes. All are optional and default to 0. - - - gpmc,sync-clk-ps: Minimum clock period for synchronous mode, in picoseconds - - Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2: - - gpmc,cs-on-ns: Assertion time - - gpmc,cs-rd-off-ns: Read deassertion time - - gpmc,cs-wr-off-ns: Write deassertion time - - ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3: - - gpmc,adv-on-ns: Assertion time - - gpmc,adv-rd-off-ns: Read deassertion time - - gpmc,adv-wr-off-ns: Write deassertion time - - gpmc,adv-aad-mux-on-ns: Assertion time for AAD - - gpmc,adv-aad-mux-rd-off-ns: Read deassertion time for AAD - - gpmc,adv-aad-mux-wr-off-ns: Write deassertion time for AAD - - WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4: - - gpmc,we-on-ns Assertion time - - gpmc,we-off-ns: Deassertion time - - OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4: - - gpmc,oe-on-ns: Assertion time - - gpmc,oe-off-ns: Deassertion time - - gpmc,oe-aad-mux-on-ns: Assertion time for AAD - - gpmc,oe-aad-mux-off-ns: Deassertion time for AAD - - Access time and cycle time timings (in nanoseconds) corresponding to - GPMC_CONFIG5: - - gpmc,page-burst-access-ns: Multiple access word delay - - gpmc,access-ns: Start-cycle to first data valid delay - - gpmc,rd-cycle-ns: Total read cycle time - - gpmc,wr-cycle-ns: Total write cycle time - - gpmc,bus-turnaround-ns: Turn-around time between successive accesses - - gpmc,cycle2cycle-delay-ns: Delay between chip-select pulses - - gpmc,clk-activation-ns: GPMC clock activation time - - gpmc,wait-monitoring-ns: Start of wait monitoring with regard to valid - data - -Boolean timing parameters. If property is present parameter enabled and -disabled if omitted: - - gpmc,adv-extra-delay: ADV signal is delayed by half GPMC clock - - gpmc,cs-extra-delay: CS signal is delayed by half GPMC clock - - gpmc,cycle2cycle-diffcsen: Add "cycle2cycle-delay" between successive - accesses to a different CS - - gpmc,cycle2cycle-samecsen: Add "cycle2cycle-delay" between successive - accesses to the same CS - - gpmc,oe-extra-delay: OE signal is delayed by half GPMC clock - - gpmc,we-extra-delay: WE signal is delayed by half GPMC clock - - gpmc,time-para-granularity: Multiply all access times by 2 - -The following are only applicable to OMAP3+ and AM335x: - - gpmc,wr-access-ns: In synchronous write mode, for single or - burst accesses, defines the number of - GPMC_FCLK cycles from start access time - to the GPMC_CLK rising edge used by the - memory device for the first data capture. - - gpmc,wr-data-mux-bus-ns: In address-data multiplex mode, specifies - the time when the first data is driven on - the address-data bus. - -GPMC chip-select settings properties for child nodes. All are optional. - -- gpmc,burst-length Page/burst length. Must be 4, 8 or 16. -- gpmc,burst-wrap Enables wrap bursting -- gpmc,burst-read Enables read page/burst mode -- gpmc,burst-write Enables write page/burst mode -- gpmc,device-width Total width of device(s) connected to a GPMC - chip-select in bytes. The GPMC supports 8-bit - and 16-bit devices and so this property must be - 1 or 2. -- gpmc,mux-add-data Address and data multiplexing configuration. - Valid values are 1 for address-address-data - multiplexing mode and 2 for address-data - multiplexing mode. -- gpmc,sync-read Enables synchronous read. Defaults to asynchronous - is this is not set. -- gpmc,sync-write Enables synchronous writes. Defaults to asynchronous - is this is not set. -- gpmc,wait-pin Wait-pin used by client. Must be less than - "gpmc,num-waitpins". -- gpmc,wait-on-read Enables wait monitoring on reads. -- gpmc,wait-on-write Enables wait monitoring on writes. - -Example for an AM33xx board: - - gpmc: gpmc@50000000 { - compatible = "ti,am3352-gpmc"; - ti,hwmods = "gpmc"; - reg = <0x50000000 0x2000>; - interrupts = <100>; - - gpmc,num-cs = <8>; - gpmc,num-waitpins = <2>; - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */ - interrupt-controller; - #interrupt-cells = <2>; - - /* child nodes go here */ - }; -- cgit v1.2.3