From cffc3df28450390f0de4d6907387d7c40459acab Mon Sep 17 00:00:00 2001 From: Mickael Guene Date: Tue, 9 Apr 2019 02:15:48 -0400 Subject: media: dt-bindings: Document MIPID02 bindings This adds documentation of device tree for MIPID02 CSI-2 to PARALLEL bridge. Reviewed-by: Rob Herring Signed-off-by: Mickael Guene Signed-off-by: Sakari Ailus Signed-off-by: Mauro Carvalho Chehab --- .../bindings/media/i2c/st,st-mipid02.txt | 82 ++++++++++++++++++++++ 1 file changed, 82 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt (limited to 'Documentation/devicetree/bindings/media') diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt new file mode 100644 index 000000000000..7976e6c40a80 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt @@ -0,0 +1,82 @@ +STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge + +MIPID02 has two CSI-2 input ports, only one of those ports can be active at a +time. Active port input stream will be de-serialized and its content outputted +through PARALLEL output port. +CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second +input port is a single lane 800Mbps. Both ports support clock and data lane +polarity swap. First port also supports data lane swap. +PARALLEL output port has a maximum width of 12 bits. +Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444, +YUV420 8-bit, YUV422 8-bit and YUV420 10-bit. + +Required Properties: +- compatible: shall be "st,st-mipid02" +- clocks: reference to the xclk input clock. +- clock-names: shall be "xclk". +- VDDE-supply: sensor digital IO supply. Must be 1.8 volts. +- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts. + +Optional Properties: +- reset-gpios: reference to the GPIO connected to the xsdn pin, if any. + This is an active low signal to the mipid02. + +Required subnodes: + - ports: A ports node with one port child node per device input and output + port, in accordance with the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + port nodes are numbered as follows: + + Port Description + ----------------------------- + 0 CSI-2 first input port + 1 CSI-2 second input port + 2 PARALLEL output + +Endpoint node required property for CSI-2 connection is: +- data-lanes: shall be <1> for Port 1. for Port 0 dual-lane operation shall be +<1 2> or <2 1>. For Port 0 single-lane operation shall be <1> or <2>. +Endpoint node optional property for CSI-2 connection is: +- lane-polarities: any lane can be inverted or not. + +Endpoint node required property for PARALLEL connection is: +- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>. +Endpoint node optional properties for PARALLEL connection are: +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +LOW being the default. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. +LOW being the default. + +Example: + +mipid02: csi2rx@14 { + compatible = "st,st-mipid02"; + reg = <0x14>; + status = "okay"; + clocks = <&clk_ext_camera_12>; + clock-names = "xclk"; + VDDE-supply = <&vdd>; + VDDIN-supply = <&vdd>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + + ep0: endpoint { + data-lanes = <1 2>; + remote-endpoint = <&mipi_csi2_in>; + }; + }; + port@2 { + reg = <2>; + + ep2: endpoint { + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + remote-endpoint = <¶llel_out>; + }; + }; + }; +}; -- cgit v1.2.3