From 27dc2fb18fe814fab0a5035859c77b279cdaec80 Mon Sep 17 00:00:00 2001 From: Joachim Eastwood Date: Wed, 6 May 2015 00:10:27 +0200 Subject: doc: dt: add documentation for lpc1850-rgu reset driver Add device tree binding documentation for the Reset Generation Unit (RGU) found on NXP LPC18xx and LPC43xx devies. This documentation also includes a table which shows the RGU reset number and the connected peripheral. Signed-off-by: Joachim Eastwood Signed-off-by: Philipp Zabel --- .../devicetree/bindings/reset/nxp,lpc1850-rgu.txt | 84 ++++++++++++++++++++++ 1 file changed, 84 insertions(+) create mode 100644 Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt (limited to 'Documentation/devicetree/bindings/reset') diff --git a/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt b/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt new file mode 100644 index 000000000000..b4e96a278445 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt @@ -0,0 +1,84 @@ +NXP LPC1850 Reset Generation Unit (RGU) +======================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "nxp,lpc1850-rgu" +- reg: register base and length +- clocks: phandle and clock specifier to RGU clocks +- clock-names: should contain "delay" and "reg" +- #reset-cells: should be 1 + +See table below for valid peripheral reset numbers. Numbers not +in the table below are either reserved or not applicable for +normal operation. + +Reset Peripheral + 9 System control unit (SCU) + 12 ARM Cortex-M0 subsystem core (LPC43xx only) + 13 CPU core + 16 LCD controller + 17 USB0 + 18 USB1 + 19 DMA + 20 SDIO + 21 External memory controller (EMC) + 22 Ethernet + 25 Flash bank A + 27 EEPROM + 28 GPIO + 29 Flash bank B + 32 Timer0 + 33 Timer1 + 34 Timer2 + 35 Timer3 + 36 Repetitive Interrupt timer (RIT) + 37 State Configurable Timer (SCT) + 38 Motor control PWM (MCPWM) + 39 QEI + 40 ADC0 + 41 ADC1 + 42 DAC + 44 USART0 + 45 UART1 + 46 USART2 + 47 USART3 + 48 I2C0 + 49 I2C1 + 50 SSP0 + 51 SSP1 + 52 I2S0 and I2S1 + 53 Serial Flash Interface (SPIFI) + 54 C_CAN1 + 55 C_CAN0 + 56 ARM Cortex-M0 application core (LPC4370 only) + 57 SGPIO (LPC43xx only) + 58 SPI (LPC43xx only) + 60 ADCHS (12-bit ADC) (LPC4370 only) + +Refer to NXP LPC18xx or LPC43xx user manual for more details about +the reset signals and the connected block/peripheral. + +Reset provider example: +rgu: reset-controller@40053000 { + compatible = "nxp,lpc1850-rgu"; + reg = <0x40053000 0x1000>; + clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_BUS>; + clock-names = "delay", "reg"; + #reset-cells = <1>; +}; + +Reset consumer example: +mac: ethernet@40010000 { + compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac"; + reg = <0x40010000 0x2000>; + interrupts = <5>; + interrupt-names = "macirq"; + clocks = <&ccu1 CLK_CPU_ETHERNET>; + clock-names = "stmmaceth"; + resets = <&rgu 22>; + reset-names = "stmmaceth"; + status = "disabled"; +}; -- cgit v1.2.3