From d6be34fbd39b7d577d25cb4edec538e8990ba07c Mon Sep 17 00:00:00 2001 From: Jingchang Lu Date: Tue, 18 Feb 2014 10:17:12 +0800 Subject: dma: Add Freescale eDMA engine driver support Add Freescale enhanced direct memory(eDMA) controller support. This module can be found on Vybrid and LS-1 SoCs. Signed-off-by: Alison Wang Signed-off-by: Jingchang Lu Acked-by: Arnd Bergmann Signed-off-by: Vinod Koul --- Documentation/devicetree/bindings/dma/fsl-edma.txt | 76 ++++++++++++++++++++++ 1 file changed, 76 insertions(+) create mode 100644 Documentation/devicetree/bindings/dma/fsl-edma.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/dma/fsl-edma.txt b/Documentation/devicetree/bindings/dma/fsl-edma.txt new file mode 100644 index 000000000000..191d7bd8a6fe --- /dev/null +++ b/Documentation/devicetree/bindings/dma/fsl-edma.txt @@ -0,0 +1,76 @@ +* Freescale enhanced Direct Memory Access(eDMA) Controller + + The eDMA channels have multiplex capability by programmble memory-mapped +registers. channels are split into two groups, called DMAMUX0 and DMAMUX1, +specific DMA request source can only be multiplexed by any channel of certain +group, DMAMUX0 or DMAMUX1, but not both. + +* eDMA Controller +Required properties: +- compatible : + - "fsl,vf610-edma" for eDMA used similar to that on Vybrid vf610 SoC +- reg : Specifies base physical address(s) and size of the eDMA registers. + The 1st region is eDMA control register's address and size. + The 2nd and the 3rd regions are programmable channel multiplexing + control register's address and size. +- interrupts : A list of interrupt-specifiers, one for each entry in + interrupt-names. +- interrupt-names : Should contain: + "edma-tx" - the transmission interrupt + "edma-err" - the error interrupt +- #dma-cells : Must be <2>. + The 1st cell specifies the DMAMUX(0 for DMAMUX0 and 1 for DMAMUX1). + Specific request source can only be multiplexed by specific channels + group called DMAMUX. + The 2nd cell specifies the request source(slot) ID. + See the SoC's reference manual for all the supported request sources. +- dma-channels : Number of channels supported by the controller +- clock-names : A list of channel group clock names. Should contain: + "dmamux0" - clock name of mux0 group + "dmamux1" - clock name of mux1 group +- clocks : A list of phandle and clock-specifier pairs, one for each entry in + clock-names. + +Optional properties: +- big-endian: If present registers and hardware scatter/gather descriptors + of the eDMA are implemented in big endian mode, otherwise in little + mode. + + +Examples: + +edma0: dma-controller@40018000 { + #dma-cells = <2>; + compatible = "fsl,vf610-edma"; + reg = <0x40018000 0x2000>, + <0x40024000 0x1000>, + <0x40025000 0x1000>; + interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>, + <0 9 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "edma-tx", "edma-err"; + dma-channels = <32>; + clock-names = "dmamux0", "dmamux1"; + clocks = <&clks VF610_CLK_DMAMUX0>, + <&clks VF610_CLK_DMAMUX1>; +}; + + +* DMA clients +DMA client drivers that uses the DMA function must use the format described +in the dma.txt file, using a two-cell specifier for each channel: the 1st +specifies the channel group(DMAMUX) in which this request can be multiplexed, +and the 2nd specifies the request source. + +Examples: + +sai2: sai@40031000 { + compatible = "fsl,vf610-sai"; + reg = <0x40031000 0x1000>; + interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "sai"; + clocks = <&clks VF610_CLK_SAI2>; + dma-names = "tx", "rx"; + dmas = <&edma0 0 21>, + <&edma0 0 20>; + status = "disabled"; +}; -- cgit v1.2.3 From cca946eae89013c2aea43c0bba71ec33887bcbf6 Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Mon, 10 Mar 2014 16:40:19 -0500 Subject: dmaengine: qcom_bam_dma: Add device tree binding Add device tree binding support for the QCOM BAM DMA driver. Acked-by: Kumar Gala Signed-off-by: Andy Gross Signed-off-by: Vinod Koul --- .../devicetree/bindings/dma/qcom_bam_dma.txt | 41 ++++++++++++++++++++++ 1 file changed, 41 insertions(+) create mode 100644 Documentation/devicetree/bindings/dma/qcom_bam_dma.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt new file mode 100644 index 000000000000..d75a9d767022 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt @@ -0,0 +1,41 @@ +QCOM BAM DMA controller + +Required properties: +- compatible: must contain "qcom,bam-v1.4.0" for MSM8974 +- reg: Address range for DMA registers +- interrupts: Should contain the one interrupt shared by all channels +- #dma-cells: must be <1>, the cell in the dmas property of the client device + represents the channel number +- clocks: required clock +- clock-names: must contain "bam_clk" entry +- qcom,ee : indicates the active Execution Environment identifier (0-7) used in + the secure world. + +Example: + + uart-bam: dma@f9984000 = { + compatible = "qcom,bam-v1.4.0"; + reg = <0xf9984000 0x15000>; + interrupts = <0 94 0>; + clocks = <&gcc GCC_BAM_DMA_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + +DMA clients must use the format described in the dma.txt file, using a two cell +specifier for each channel. + +Example: + serial@f991e000 { + compatible = "qcom,msm-uart"; + reg = <0xf991e000 0x1000> + <0xf9944000 0x19000>; + interrupts = <0 108 0>; + clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + + dmas = <&uart-bam 0>, <&uart-bam 1>; + dma-names = "rx", "tx"; + }; -- cgit v1.2.3 From 2e041c94628c2f0b8b704dc092802ddeaa70c6e9 Mon Sep 17 00:00:00 2001 From: Barry Song Date: Thu, 27 Mar 2014 15:49:31 +0800 Subject: dmaengine: sirf: enable generic dt binding for dma channels move to support of_dma_request_slave_channel() and dma_request_slave_channel. we add a xlate() to let dma clients be able to find right dma_chan by generic "dmas" properties in dts. Cc: Mark Rutland Cc: Lars-Peter Clausen Signed-off-by: Barry Song Acked-by: Arnd Bergmann Signed-off-by: Vinod Koul --- .../devicetree/bindings/dma/sirfsoc-dma.txt | 43 ++++++++++++++++++++++ 1 file changed, 43 insertions(+) create mode 100644 Documentation/devicetree/bindings/dma/sirfsoc-dma.txt (limited to 'Documentation/devicetree/bindings') diff --git a/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt b/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt new file mode 100644 index 000000000000..ecbc96ad36f8 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt @@ -0,0 +1,43 @@ +* CSR SiRFSoC DMA controller + +See dma.txt first + +Required properties: +- compatible: Should be "sirf,prima2-dmac" or "sirf,marco-dmac" +- reg: Should contain DMA registers location and length. +- interrupts: Should contain one interrupt shared by all channel +- #dma-cells: must be <1>. used to represent the number of integer + cells in the dmas property of client device. +- clocks: clock required + +Example: + +Controller: +dmac0: dma-controller@b00b0000 { + compatible = "sirf,prima2-dmac"; + reg = <0xb00b0000 0x10000>; + interrupts = <12>; + clocks = <&clks 24>; + #dma-cells = <1>; +}; + + +Client: +Fill the specific dma request line in dmas. In the below example, spi0 read +channel request line is 9 of the 2nd dma controller, while write channel uses +4 of the 2nd dma controller; spi1 read channel request line is 12 of the 1st +dma controller, while write channel uses 13 of the 1st dma controller: + +spi0: spi@b00d0000 { + compatible = "sirf,prima2-spi"; + dmas = <&dmac1 9>, + <&dmac1 4>; + dma-names = "rx", "tx"; +}; + +spi1: spi@b0170000 { + compatible = "sirf,prima2-spi"; + dmas = <&dmac0 12>, + <&dmac0 13>; + dma-names = "rx", "tx"; +}; -- cgit v1.2.3