From 677b2ff4afd9996eabefc9472c701211b4b49e87 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 2 Oct 2015 14:26:05 -0700 Subject: gpio: add a real time compliance checklist Add some information about real time compliance to the driver document. Inspired by Grygorii Strashko's real time compliance patches. Cc: Grygorii Strashko Signed-off-by: Linus Walleij --- Documentation/gpio/driver.txt | 72 +++++++++++++++++++++++++++++++++++-------- 1 file changed, 60 insertions(+), 12 deletions(-) (limited to 'Documentation/gpio') diff --git a/Documentation/gpio/driver.txt b/Documentation/gpio/driver.txt index 90d0f6aba7a6..9d7985171f07 100644 --- a/Documentation/gpio/driver.txt +++ b/Documentation/gpio/driver.txt @@ -93,22 +93,37 @@ GPIO irqchips usually fall in one of two categories: Chained GPIO irqchips typically can NOT set the .can_sleep flag on struct gpio_chip, as everything happens directly in the callbacks. -* NESTED THREADED GPIO irqchips: these are off-chip GPIO expanders and any - other GPIO irqchip residing on the other side of a sleeping bus. Of course - such drivers that need slow bus traffic to read out IRQ status and similar, - traffic which may in turn incur other IRQs to happen, cannot be handled - in a quick IRQ handler with IRQs disabled. Instead they need to spawn a - thread and then mask the parent IRQ line until the interrupt is handled - by the driver. The hallmark of this driver is to call something like - this in its interrupt handler: + NOTE: chained IRQ handlers are usually not good for real time. If you + are submitting a new driver or refactoring a driver for real time compliance, + consider using creating a nested/threaded irqchip instead, see below. + +* NESTED THREADED GPIO irqchips: these are traditionally off-chip GPIO + expanders and any other GPIO irqchip residing on the other side of a + sleeping bus. Of course such drivers that need slow bus traffic to read + out IRQ status and similar, traffic which may in turn incur other IRQs to + happen, cannot be handled in a quick IRQ handler with IRQs disabled. + + With the introduction of real time support in the Linux kernel, also other + GPIO irqchips are encouraged to use a nested and threaded IRQ handler. + Doing so makes the interrupts naturally preemptible on a real time + setup, which means the system can easily be configured for real time with + a (usually negligable) performance loss. + + These drivers spawn a thread and then mask the parent IRQ line until the + interrupt is handled by the driver. The hallmark of this driver is to call + something like this in its interrupt handler: static irqreturn_t tc3589x_gpio_irq(int irq, void *data) ... handle_nested_irq(irq); + OR + generic_handle_irq(irq); - The hallmark of threaded GPIO irqchips is that they set the .can_sleep - flag on struct gpio_chip to true, indicating that this chip may sleep - when accessing the GPIOs. + Threaded GPIO irqchips should set the .can_sleep flag on struct gpio_chip + to true if they are e.g. accessing the chip over I2C or SPI, indicating that + this chip may sleep when accessing the GPIOs. irqchips that are just made + threaded to be preemptible and thus real time compliant need not do this: + preemption is not sleeping. To help out in handling the set-up and management of GPIO irqchips and the associated irqdomain and resource allocation callbacks, the gpiolib has @@ -125,7 +140,7 @@ symbol: gpio_chip from a parent IRQ and passes the struct gpio_chip* as handler data. (Notice handler data, since the irqchip data is likely used by the parent irqchip!) This is for the chained type of chip. This is also used - to set up a nested irqchip if NULL is passed as handler. + to set up a threaded/nested irqchip if NULL is passed as handler. To use the helpers please keep the following in mind: @@ -170,6 +185,39 @@ typically be called in the .startup() and .shutdown() callbacks from the irqchip. +Real-Time compliance for GPIO IRQ chips +--------------------------------------- + +Any provider of irqchips needs to be carefully tailored to support Real Time +preemption. It is desireable that all irqchips in the GPIO subsystem keep this +in mind and does the proper testing to assure they are real time-enabled. The +following is a checklist to follow when preparing a driver for real +time-compliance: + +- Nominally use raw_spinlock_t in the IRQ context path of the IRQ handler as + we do not want these sections to be preempted. + +- Do NOT use chained_irq_enter() or chained_irq_exit() in the IRQ handler, + as we want the hotpath to be preemptible. + +- Instead use nested IRQs and generic handlers such as handle_bad_irq(), + handle_level_irq() and handle_edge_irq(). Consequentally the handler + argument of gpiochip_set_chained_irqchip() should be NULL when using the + gpiolib irqchip helpers. + +- Nominally set all handlers to handle_bad_irq() in the setup call, then + set the handler to handle_level_irq() and/or handle_edge_irq() in the irqchip + .set_type() callback depending on what your controller supports. + +- If you need to use the pm_runtime_get*()/pm_runtime_put*() callbacks in some + of the irqchip callbacks, these should be moved to the .irq_bus_lock() + and .irq_bus_unlock() callbacks respectively, as these are the only + slowpath callbacks on an irqchip. Create the callbacks if need be. + +- Test your driver with the apropriate in-kernel real time test cases for both + level and edge IRQs. + + Requesting self-owned GPIO pins ------------------------------- -- cgit v1.2.3