From c5114a1cd6d84b2b3144c1c3e093c80ca6c30f47 Mon Sep 17 00:00:00 2001 From: Clemens Ladisch Date: Sun, 10 Jan 2010 20:52:34 +0100 Subject: hwmon: (k10temp) Blacklist more family 10h processors The latest version of the Revision Guide for AMD Family 10h Processors lists two more processor revisions which may be affected by erratum 319. Change the blacklisting code to correctly detect those processors, by implementing AMD's recommended algorithm. Signed-off-by: Clemens Ladisch Signed-off-by: Jean Delvare Cc: Andreas Herrmann --- Documentation/hwmon/k10temp | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-) (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/k10temp b/Documentation/hwmon/k10temp index a7a18d453a51..6526eee525a6 100644 --- a/Documentation/hwmon/k10temp +++ b/Documentation/hwmon/k10temp @@ -3,8 +3,8 @@ Kernel driver k10temp Supported chips: * AMD Family 10h processors: - Socket F: Quad-Core/Six-Core/Embedded Opteron - Socket AM2+: Opteron, Phenom (II) X3/X4 + Socket F: Quad-Core/Six-Core/Embedded Opteron (but see below) + Socket AM2+: Quad-Core Opteron, Phenom (II) X3/X4, Athlon X2 (but see below) Socket AM3: Quad-Core Opteron, Athlon/Phenom II X2/X3/X4, Sempron II Socket S1G3: Athlon II, Sempron, Turion II * AMD Family 11h processors: @@ -36,10 +36,15 @@ Description This driver permits reading of the internal temperature sensor of AMD Family 10h and 11h processors. -All these processors have a sensor, but on older revisions of Family 10h -processors, the sensor may return inconsistent values (erratum 319). The -driver will refuse to load on these revisions unless you specify the -"force=1" module parameter. +All these processors have a sensor, but on those for Socket F or AM2+, +the sensor may return inconsistent values (erratum 319). The driver +will refuse to load on these revisions unless you specify the "force=1" +module parameter. + +Due to technical reasons, the driver can detect only the mainboard's +socket type, not the processor's actual capabilities. Therefore, if you +are using an AM3 processor on an AM2+ mainboard, you can safely use the +"force=1" parameter. There is one temperature measurement value, available as temp1_input in sysfs. It is measured in degrees Celsius with a resolution of 1/8th degree. -- cgit v1.2.3 From b5430a04e995081a308b4419bd0940f2badc6e6b Mon Sep 17 00:00:00 2001 From: Tomaz Mertelj Date: Fri, 8 Jan 2010 14:43:04 -0800 Subject: hwmon: driver for Texas Instruments amc6821 chip Signed-off-by: Cc: Jean Delvare Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- Documentation/hwmon/amc6821 | 102 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 102 insertions(+) create mode 100644 Documentation/hwmon/amc6821 (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/amc6821 b/Documentation/hwmon/amc6821 new file mode 100644 index 000000000000..ced8359c50f8 --- /dev/null +++ b/Documentation/hwmon/amc6821 @@ -0,0 +1,102 @@ +Kernel driver amc6821 +===================== + +Supported chips: + Texas Instruments AMC6821 + Prefix: 'amc6821' + Addresses scanned: 0x18, 0x19, 0x1a, 0x2c, 0x2d, 0x2e, 0x4c, 0x4d, 0x4e + Datasheet: http://focus.ti.com/docs/prod/folders/print/amc6821.html + +Authors: + Tomaz Mertelj + + +Description +----------- + +This driver implements support for the Texas Instruments amc6821 chip. +The chip has one on-chip and one remote temperature sensor and one pwm fan +regulator. +The pwm can be controlled either from software or automatically. + +The driver provides the following sensor accesses in sysfs: + +temp1_input ro on-chip temperature +temp1_min rw " +temp1_max rw " +temp1_crit rw " +temp1_min_alarm ro " +temp1_max_alarm ro " +temp1_crit_alarm ro " + +temp2_input ro remote temperature +temp2_min rw " +temp2_max rw " +temp2_crit rw " +temp2_min_alarm ro " +temp2_max_alarm ro " +temp2_crit_alarm ro " +temp2_fault ro " + +fan1_input ro tachometer speed +fan1_min rw " +fan1_max rw " +fan1_fault ro " +fan1_div rw Fan divisor can be either 2 or 4. + +pwm1 rw pwm1 +pwm1_enable rw regulator mode, 1=open loop, 2=fan controlled + by remote temperature, 3=fan controlled by + combination of the on-chip temperature and + remote-sensor temperature, +pwm1_auto_channels_temp ro 1 if pwm_enable==2, 3 if pwm_enable==3 +pwm1_auto_point1_pwm ro Hardwired to 0, shared for both + temperature channels. +pwm1_auto_point2_pwm rw This value is shared for both temperature + channels. +pwm1_auto_point3_pwm rw Hardwired to 255, shared for both + temperature channels. + +temp1_auto_point1_temp ro Hardwired to temp2_auto_point1_temp + which is rw. Below this temperature fan stops. +temp1_auto_point2_temp rw The low-temperature limit of the proportional + range. Below this temperature + pwm1 = pwm1_auto_point2_pwm. It can go from + 0 degree C to 124 degree C in steps of + 4 degree C. Read it out after writing to get + the actual value. +temp1_auto_point3_temp rw Above this temperature fan runs at maximum + speed. It can go from temp1_auto_point2_temp. + It can only have certain discrete values + which depend on temp1_auto_point2_temp and + pwm1_auto_point2_pwm. Read it out after + writing to get the actual value. + +temp2_auto_point1_temp rw Must be between 0 degree C and 63 degree C and + it defines the passive cooling temperature. + Below this temperature the fan stops in + the closed loop mode. +temp2_auto_point2_temp rw The low-temperature limit of the proportional + range. Below this temperature + pwm1 = pwm1_auto_point2_pwm. It can go from + 0 degree C to 124 degree C in steps + of 4 degree C. + +temp2_auto_point3_temp rw Above this temperature fan runs at maximum + speed. It can only have certain discrete + values which depend on temp2_auto_point2_temp + and pwm1_auto_point2_pwm. Read it out after + writing to get actual value. + + +Module parameters +----------------- + +If your board has a BIOS that initializes the amc6821 correctly, you should +load the module with: init=0. + +If your board BIOS doesn't initialize the chip, or you want +different settings, you can set the following parameters: +init=1, +pwminv: 0 default pwm output, 1 inverts pwm output. + -- cgit v1.2.3