From 614f60fa9d73a9e8fdff3df83381907fea7c5649 Mon Sep 17 00:00:00 2001 From: Scott McMillan Date: Wed, 2 Jun 2010 05:53:56 -0700 Subject: packet_mmap: expose hw packet timestamps to network packet capture utilities This patch adds a setting, PACKET_TIMESTAMP, to specify the packet timestamp source that is exported to capture utilities like tcpdump by packet_mmap. PACKET_TIMESTAMP accepts the same integer bit field as SO_TIMESTAMPING. However, only the SOF_TIMESTAMPING_SYS_HARDWARE and SOF_TIMESTAMPING_RAW_HARDWARE values are currently recognized by PACKET_TIMESTAMP. SOF_TIMESTAMPING_SYS_HARDWARE takes precedence over SOF_TIMESTAMPING_RAW_HARDWARE if both bits are set. If PACKET_TIMESTAMP is not set, a software timestamp generated inside the networking stack is used (the behavior before this setting was added). Signed-off-by: Scott McMillan Signed-off-by: David S. Miller --- Documentation/networking/packet_mmap.txt | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+) (limited to 'Documentation') diff --git a/Documentation/networking/packet_mmap.txt b/Documentation/networking/packet_mmap.txt index 98f71a5cef00..2546aa4dc232 100644 --- a/Documentation/networking/packet_mmap.txt +++ b/Documentation/networking/packet_mmap.txt @@ -493,6 +493,32 @@ The user can also use poll() to check if a buffer is available: pfd.events = POLLOUT; retval = poll(&pfd, 1, timeout); +------------------------------------------------------------------------------- ++ PACKET_TIMESTAMP +------------------------------------------------------------------------------- + +The PACKET_TIMESTAMP setting determines the source of the timestamp in +the packet meta information. If your NIC is capable of timestamping +packets in hardware, you can request those hardware timestamps to used. +Note: you may need to enable the generation of hardware timestamps with +SIOCSHWTSTAMP. + +PACKET_TIMESTAMP accepts the same integer bit field as +SO_TIMESTAMPING. However, only the SOF_TIMESTAMPING_SYS_HARDWARE +and SOF_TIMESTAMPING_RAW_HARDWARE values are recognized by +PACKET_TIMESTAMP. SOF_TIMESTAMPING_SYS_HARDWARE takes precedence over +SOF_TIMESTAMPING_RAW_HARDWARE if both bits are set. + + int req = 0; + req |= SOF_TIMESTAMPING_SYS_HARDWARE; + setsockopt(fd, SOL_PACKET, PACKET_TIMESTAMP, (void *) &req, sizeof(req)) + +If PACKET_TIMESTAMP is not set, a software timestamp generated inside +the networking stack is used (the behavior before this setting was added). + +See include/linux/net_tstamp.h and Documentation/networking/timestamping +for more information on hardware timestamps. + -------------------------------------------------------------------------------- + THANKS -------------------------------------------------------------------------------- -- cgit v1.2.3 From 8cbccbe76168a0c627d2274e4a322116804db30f Mon Sep 17 00:00:00 2001 From: Wu Fengguang Date: Wed, 2 Jun 2010 16:02:44 +0000 Subject: ipconfig: document DHCP hostname and DNS record Now it's possible to update the DNS record for $HOST_NAME with ip=::::$HOST_NAME::dhcp CC: Andi Kleen Signed-off-by: Wu Fengguang Signed-off-by: David S. Miller --- Documentation/filesystems/nfs/nfsroot.txt | 2 ++ 1 file changed, 2 insertions(+) (limited to 'Documentation') diff --git a/Documentation/filesystems/nfs/nfsroot.txt b/Documentation/filesystems/nfs/nfsroot.txt index 3ba0b945aaf8..f2430a7974e1 100644 --- a/Documentation/filesystems/nfs/nfsroot.txt +++ b/Documentation/filesystems/nfs/nfsroot.txt @@ -124,6 +124,8 @@ ip=:::::: Name of the client. May be supplied by autoconfiguration, but its absence will not trigger autoconfiguration. + If specified and DHCP is used, the user provided hostname will + be carried in the DHCP request to hopefully update DNS record. Default: Client IP address is used in ASCII notation. -- cgit v1.2.3 From bb1d912323d5dd50e1079e389f4e964be14f0ae3 Mon Sep 17 00:00:00 2001 From: Andy Gospodarek Date: Wed, 2 Jun 2010 08:40:18 +0000 Subject: bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek Signed-off-by: Neil Horman Signed-off-by: David S. Miller --- Documentation/networking/bonding.txt | 84 +++++++++++++++++++++++++++++++++++- 1 file changed, 82 insertions(+), 2 deletions(-) (limited to 'Documentation') diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index 61f516b135b4..d0914781830e 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -49,6 +49,7 @@ Table of Contents 3.3 Configuring Bonding Manually with Ifenslave 3.3.1 Configuring Multiple Bonds Manually 3.4 Configuring Bonding Manually via Sysfs +3.5 Overriding Configuration for Special Cases 4. Querying Bonding Configuration 4.1 Bonding Configuration @@ -1318,8 +1319,87 @@ echo 2000 > /sys/class/net/bond1/bonding/arp_interval echo +eth2 > /sys/class/net/bond1/bonding/slaves echo +eth3 > /sys/class/net/bond1/bonding/slaves - -4. Querying Bonding Configuration +3.5 Overriding Configuration for Special Cases +---------------------------------------------- +When using the bonding driver, the physical port which transmits a frame is +typically selected by the bonding driver, and is not relevant to the user or +system administrator. The output port is simply selected using the policies of +the selected bonding mode. On occasion however, it is helpful to direct certain +classes of traffic to certain physical interfaces on output to implement +slightly more complex policies. For example, to reach a web server over a +bonded interface in which eth0 connects to a private network, while eth1 +connects via a public network, it may be desirous to bias the bond to send said +traffic over eth0 first, using eth1 only as a fall back, while all other traffic +can safely be sent over either interface. Such configurations may be achieved +using the traffic control utilities inherent in linux. + +By default the bonding driver is multiqueue aware and 16 queues are created +when the driver initializes (see Documentation/networking/multiqueue.txt +for details). If more or less queues are desired the module parameter +tx_queues can be used to change this value. There is no sysfs parameter +available as the allocation is done at module init time. + +The output of the file /proc/net/bonding/bondX has changed so the output Queue +ID is now printed for each slave: + +Bonding Mode: fault-tolerance (active-backup) +Primary Slave: None +Currently Active Slave: eth0 +MII Status: up +MII Polling Interval (ms): 0 +Up Delay (ms): 0 +Down Delay (ms): 0 + +Slave Interface: eth0 +MII Status: up +Link Failure Count: 0 +Permanent HW addr: 00:1a:a0:12:8f:cb +Slave queue ID: 0 + +Slave Interface: eth1 +MII Status: up +Link Failure Count: 0 +Permanent HW addr: 00:1a:a0:12:8f:cc +Slave queue ID: 2 + +The queue_id for a slave can be set using the command: + +# echo "eth1:2" > /sys/class/net/bond0/bonding/queue_id + +Any interface that needs a queue_id set should set it with multiple calls +like the one above until proper priorities are set for all interfaces. On +distributions that allow configuration via initscripts, multiple 'queue_id' +arguments can be added to BONDING_OPTS to set all needed slave queues. + +These queue id's can be used in conjunction with the tc utility to configure +a multiqueue qdisc and filters to bias certain traffic to transmit on certain +slave devices. For instance, say we wanted, in the above configuration to +force all traffic bound to 192.168.1.100 to use eth1 in the bond as its output +device. The following commands would accomplish this: + +# tc qdisc add dev bond0 handle 1 root multiq + +# tc filter add dev bond0 protocol ip parent 1: prio 1 u32 match ip dst \ + 192.168.1.100 action skbedit queue_mapping 2 + +These commands tell the kernel to attach a multiqueue queue discipline to the +bond0 interface and filter traffic enqueued to it, such that packets with a dst +ip of 192.168.1.100 have their output queue mapping value overwritten to 2. +This value is then passed into the driver, causing the normal output path +selection policy to be overridden, selecting instead qid 2, which maps to eth1. + +Note that qid values begin at 1. Qid 0 is reserved to initiate to the driver +that normal output policy selection should take place. One benefit to simply +leaving the qid for a slave to 0 is the multiqueue awareness in the bonding +driver that is now present. This awareness allows tc filters to be placed on +slave devices as well as bond devices and the bonding driver will simply act as +a pass-through for selecting output queues on the slave device rather than +output port selection. + +This feature first appeared in bonding driver version 3.7.0 and support for +output slave selection was limited to round-robin and active-backup modes. + +4 Querying Bonding Configuration ================================= 4.1 Bonding Configuration -- cgit v1.2.3 From 43d28b6515a6ea580a198df3e253e88236f08978 Mon Sep 17 00:00:00 2001 From: Daniel Turull Date: Wed, 9 Jun 2010 22:49:57 +0000 Subject: pktgen: increasing transmission granularity This patch increases the granularity of the rate generated by pktgen. The previous version of pktgen uses micro seconds (udelay) resolution when it was delayed causing gaps in the rates. It is changed to nanosecond (ndelay). Now any rate is possible. Also it allows to set, the desired rate in Mb/s or packets per second. The documentation has been updated. Signed-off-by: Daniel Turull Signed-off-by: Robert Olsson Signed-off-by: David S. Miller --- Documentation/networking/pktgen.txt | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'Documentation') diff --git a/Documentation/networking/pktgen.txt b/Documentation/networking/pktgen.txt index 61bb645d50e0..75e4fd708ccb 100644 --- a/Documentation/networking/pktgen.txt +++ b/Documentation/networking/pktgen.txt @@ -151,6 +151,8 @@ Examples: pgset stop aborts injection. Also, ^C aborts generator. + pgset "rate 300M" set rate to 300 Mb/s + pgset "ratep 1000000" set rate to 1Mpps Example scripts =============== @@ -241,6 +243,9 @@ src6 flows flowlen +rate +ratep + References: ftp://robur.slu.se/pub/Linux/net-development/pktgen-testing/ ftp://robur.slu.se/pub/Linux/net-development/pktgen-testing/examples/ -- cgit v1.2.3