From 4f5e01e96d424b54f5f0e89ee1ba9ccca03a3941 Mon Sep 17 00:00:00 2001 From: Andrew Lunn Date: Mon, 1 Sep 2014 19:35:41 +0200 Subject: ARM: Kirkwood: Fix DT based DSA. During the conversion of boards to use DT to instantiate Distributed Switch Architecture, nobody volunteered to test. As to be expected, the conversion was flawed. Testers and access to hardware has now become available, and this patch hopefully fixes the problems. dsa,mii-bus must be a phandle to the top level mdio node, not the port specific subnode of the mdio device. dsa,ethernet must be a phandle to the port subnode within the ethernet DT node, not the ethernet node. Don't pinctrl hog the card detect gpio for mvsdio. Rename the .dts files to make it clearer which file is for the Z0 stepping and which for the A0 or later stepping. Signed-off-by: Andrew Lunn Cc: seugene@marvell.com Tested-by: Eugene Sanivsky Fixes: e2eaa339af44: ("ARM: Kirkwood: convert rd88f6281-setup.c to DT.") Fixes: e7c8f3808be8: ("ARM: kirkwood: Convert mv88f6281gtw_ge switch setup to DT") Cc: #v3.15+ Link: https://lkml.kernel.org/r/1409592941-22244-1-git-send-email-andrew@lunn.ch Signed-off-by: Jason Cooper --- arch/arm/boot/dts/kirkwood-rd88f6281.dtsi | 27 +++++---------------------- 1 file changed, 5 insertions(+), 22 deletions(-) (limited to 'arch/arm/boot/dts/kirkwood-rd88f6281.dtsi') diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi b/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi index 26cf0e0ccefd..d195e884b3b5 100644 --- a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi +++ b/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi @@ -37,7 +37,6 @@ ocp@f1000000 { pinctrl: pin-controller@10000 { - pinctrl-0 = <&pmx_sdio_cd>; pinctrl-names = "default"; pmx_sdio_cd: pmx-sdio-cd { @@ -69,8 +68,8 @@ #address-cells = <2>; #size-cells = <0>; - dsa,ethernet = <ð0>; - dsa,mii-bus = <ðphy1>; + dsa,ethernet = <ð0port>; + dsa,mii-bus = <&mdio>; switch@0 { #address-cells = <1>; @@ -119,35 +118,19 @@ }; partition@300000 { - label = "data"; + label = "rootfs"; reg = <0x0300000 0x500000>; }; }; &mdio { status = "okay"; - - ethphy0: ethernet-phy@0 { - reg = <0>; - }; - - ethphy1: ethernet-phy@ff { - reg = <0xff>; /* No PHY attached */ - speed = <1000>; - duple = <1>; - }; }; ð0 { status = "okay"; ethernet0-port@0 { - phy-handle = <ðphy0>; - }; -}; - -ð1 { - status = "okay"; - ethernet1-port@0 { - phy-handle = <ðphy1>; + speed = <1000>; + duplex = <1>; }; }; -- cgit v1.2.3