From 1d8aca9df612f5751892fb2642d72536f2f48fd0 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Wed, 8 Jul 2015 15:15:22 +0200 Subject: ARM: ux500: fix MMC/SD card regression Ux500 is regressing due to commit a21763a0b1e5a5ab8310f581886d04beadc16616 "pinctrl: nomadik: activate strict mux mode" which disallows Nomadik GPIO 5 to be muxed in as a level shifter voltage select pin, as it is currently described as being used for RX on UART1. The behaviour is correct, instead the hardware config has been incorrecly specified: UART1 is indeed unused on HREFv60plus and Snowball and that is why HREFv60plus can use the pins it would normally occupy as the voltage select line for the MMC/SD levelshifter (Snowball uses it for I2C4). The reason UART1 was anyway enabled on these platforms was probably to secure the port enumeration to userspace. This can be solved by using aliases (done in a separate patch) so we can now deactivate UART1 and let MMC/SD use it properly on HREFv60plus. We explicitly activate it only for the older HREFprev60 board. To complete, we set up the pin configuration for these pins properly in the sdi0 node. Cc: Ulf Hansson Signed-off-by: Linus Walleij Signed-off-by: Olof Johansson --- arch/arm/boot/dts/ste-hrefv60plus.dtsi | 25 +++++++++++++++++++++++-- 1 file changed, 23 insertions(+), 2 deletions(-) (limited to 'arch/arm/boot/dts/ste-hrefv60plus.dtsi') diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi index a4bc9e77d640..810cda743b6d 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi +++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi @@ -43,15 +43,26 @@ <&vaudio_hf_hrefv60_mode>, <&gbf_hrefv60_mode>, <&hdtv_hrefv60_mode>, - <&touch_hrefv60_mode>; + <&touch_hrefv60_mode>, + <&gpios_hrefv60_mode>; sdi0 { - /* SD card detect GPIO pin, extend default state */ sdi0_default_mode: sdi0_default { + /* SD card detect GPIO pin, extend default state */ default_hrefv60_cfg1 { pins = "GPIO95_E8"; ste,config = <&gpio_in_pu>; }; + /* VMMCI level-shifter enable */ + default_hrefv60_cfg2 { + pins = "GPIO169_D22"; + ste,config = <&gpio_out_lo>; + }; + /* VMMCI level-shifter voltage select */ + default_hrefv60_cfg3 { + pins = "GPIO5_AG6"; + ste,config = <&gpio_out_hi>; + }; }; }; ipgpio { @@ -213,6 +224,16 @@ }; }; }; + gpios { + /* Dangling GPIO pins */ + gpios_hrefv60_mode: gpios_hrefv60 { + default_cfg1 { + /* Normally UART1 RXD, now dangling */ + pins = "GPIO4_AH6"; + ste,config = <&in_pu>; + }; + }; + }; }; }; }; -- cgit v1.2.3