From e3c83c2db458f1e040c5b4bb19773c458e0240a8 Mon Sep 17 00:00:00 2001 From: NeilBrown Date: Wed, 25 Apr 2012 13:05:24 +1000 Subject: ARM: OMAP2+: INTC: fix suspend abort, set IRQCHIP_SKIP_SET_WAKE Without an ->irq_set_wake() method in an irq_chip, calls to enable_irq_wake() will fail. This also causes these interrupts to not be able to abort suspend (via check_wakeup_irqs() in late suspend.) Currently, we don't implement ->irq_set_wake() for INTC interrupts because they default to be wakeup enabled by setting the GRPSEL bits in PM init. Even though there is no ->irq_set_wake(), we want enable_irq_wake() to succeed so these interrupts can abort suspend when necessary. To fix, set IRQCHIP_SKIP_SET_WAKE flag for all the INTC interrupts which avoids trying to check irq_chip->irq_set_wake() and failing when it doesn't exist. Longer term, we need to implement ->irq_set_wake() for the INTC which can manage the appropriate GRPSEL bits. Signed-off-by: NeilBrown [khilman@ti.com: rework changelog] Acked-by: Santosh Shilimkar Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/irq.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/irq.c b/arch/arm/mach-omap2/irq.c index 65f0d2571c9a..b0790a995dc9 100644 --- a/arch/arm/mach-omap2/irq.c +++ b/arch/arm/mach-omap2/irq.c @@ -148,6 +148,7 @@ omap_alloc_gc(void __iomem *base, unsigned int irq_start, unsigned int num) ct->chip.irq_ack = omap_mask_ack_irq; ct->chip.irq_mask = irq_gc_mask_disable_reg; ct->chip.irq_unmask = irq_gc_unmask_enable_reg; + ct->chip.flags |= IRQCHIP_SKIP_SET_WAKE; ct->regs.ack = INTC_CONTROL; ct->regs.enable = INTC_MIR_CLEAR0; -- cgit v1.2.3 From 99b59df04899a048d1a3ed8bc2b1263779816868 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Fri, 27 Apr 2012 16:05:51 -0700 Subject: ARM: OMAP3: PM: fix shared PRCM interrupts: leave disabled at boot By default, request_irq() will auto-enable the requested IRQ. For PRCM interrupts, we may want to avoid that until the PM core code is fully ready to handle the interrupts. This is particularily true for IO pad interrupts on OMAP3, which are shared between the hwmod core and the PRM core. In order to avoid PRCM IO-chain interrupts until the PM core is ready to handle them, ready, set the IRQ_NOAUTOEN flag for the PRCM IO-chain interrupt, which means it will remain disabled after request_irq(). Then, explicitly enable the PRCM interrupts after the request_irq() in the PM core (but not in the hwmod core.) Special thanks to Tero Kristo for suggesting to isolate the fix to only the IO-chain interrupt on OMAP3 instead of all PRCM interrupts. Cc: Tero Kristo Acked-by: Paul Walmsley Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 1 + arch/arm/mach-omap2/prm2xxx_3xxx.c | 14 +++++++++++--- 2 files changed, 12 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 703bd1099259..4f44ee517f78 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -729,6 +729,7 @@ static int __init omap3_pm_init(void) ret = request_irq(omap_prcm_event_to_irq("io"), _prcm_int_handle_io, IRQF_SHARED | IRQF_NO_SUSPEND, "pm_io", omap3_pm_init); + enable_irq(omap_prcm_event_to_irq("io")); if (ret) { pr_err("pm: Failed to request pm_io irq\n"); diff --git a/arch/arm/mach-omap2/prm2xxx_3xxx.c b/arch/arm/mach-omap2/prm2xxx_3xxx.c index 9ce765407ad5..21cb74003a56 100644 --- a/arch/arm/mach-omap2/prm2xxx_3xxx.c +++ b/arch/arm/mach-omap2/prm2xxx_3xxx.c @@ -15,6 +15,7 @@ #include #include #include +#include #include "common.h" #include @@ -303,8 +304,15 @@ void omap3xxx_prm_restore_irqen(u32 *saved_mask) static int __init omap3xxx_prcm_init(void) { - if (cpu_is_omap34xx()) - return omap_prcm_register_chain_handler(&omap3_prcm_irq_setup); - return 0; + int ret = 0; + + if (cpu_is_omap34xx()) { + ret = omap_prcm_register_chain_handler(&omap3_prcm_irq_setup); + if (!ret) + irq_set_status_flags(omap_prcm_event_to_irq("io"), + IRQ_NOAUTOEN); + } + + return ret; } subsys_initcall(omap3xxx_prcm_init); -- cgit v1.2.3 From 1ce029968718477149e7f1fb245a8e82c690cc4a Mon Sep 17 00:00:00 2001 From: "Mark A. Greer" Date: Mon, 30 Apr 2012 16:57:09 -0700 Subject: arm: omap3: am35x: Don't mark missing features as present The Chip Identification register on the am35x family of SoCs has bits 12, 7:5, and 3:2 marked as reserved and are read as zeroes. Unfortunately, on other omap SoCs, a 0 bit means a feature is "Full Use" so the OMAP3_CHECK_FEATURE() macro called by omap3_check_features() will incorrectly interpret those zeroes to mean that a feature is present even though it isn't. To fix that, the feature bits that are incorrectly set (namely, OMAP3_HAS_IVA and OMAP3_HAS_ISP) need to be cleared after all of the calls to OMAP3_CHECK_FEATURE() in omap3_check_features() are made. Signed-off-by: Mark A. Greer [khilman@ti.com: use soc_is_am35xx() instead of cpu_is_am35xx()] Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/id.c | 11 +++++++++++ 1 file changed, 11 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index f611e3097157..38ae74f8e77a 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -246,6 +246,17 @@ void __init omap3xxx_check_features(void) omap_features |= OMAP3_HAS_SDRC; + /* + * am35x fixups: + * - The am35x Chip ID register has bits 12, 7:5, and 3:2 marked as + * reserved and therefore return 0 when read. Unfortunately, + * OMAP3_CHECK_FEATURE() will interpret some of those zeroes to + * mean that a feature is present even though it isn't so clear + * the incorrectly set feature bits. + */ + if (soc_is_am35xx()) + omap_features &= ~(OMAP3_HAS_IVA | OMAP3_HAS_ISP); + /* * TODO: Get additional info (where applicable) * e.g. Size of L2 cache. -- cgit v1.2.3 From 00633d7c7a0243940fc616bee573bcf497db79b9 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 4 Jan 2012 15:33:17 -0800 Subject: ARM: OMAP3: clock data: cleanup AM3[35]x SoC detection Use the more generic SoC family soc_is_am35xx() instead of the specific cpu_is_omap3517() (which is being removed.) Acked-by: Vaibhav Hiremath Tested-by: Vaibhav Hiremath Tested-by: Mark A. Greer Cc: Paul Walmsley Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/clock3xxx_data.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock3xxx_data.c b/arch/arm/mach-omap2/clock3xxx_data.c index 4e1a3b0e8cc8..1efdec236ae8 100644 --- a/arch/arm/mach-omap2/clock3xxx_data.c +++ b/arch/arm/mach-omap2/clock3xxx_data.c @@ -3514,7 +3514,7 @@ int __init omap3xxx_clk_init(void) struct omap_clk *c; u32 cpu_clkflg = 0; - if (cpu_is_omap3517()) { + if (soc_is_am35xx()) { cpu_mask = RATE_IN_34XX; cpu_clkflg = CK_AM35XX; } else if (cpu_is_omap3630()) { -- cgit v1.2.3 From 4d04317f6efab7359ae56e50cc9c60e9804b5015 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 4 Jun 2012 00:13:25 -0700 Subject: ARM: OMAP: Fix lis3lv02d accelerometer to use gpio_to_irq Commit 3b511201 (ARM: OMAP: rx51: Platform support for lis3lv02d accelerometer) added support for lis3lv02d accelerometer. The patch was still using OMAP_GPIO_IRQ which no longer exists. Fix it by using gpio_to_irq(). Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-rx51-peripherals.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index ff53deccecab..df2534de3361 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -144,7 +144,6 @@ static struct lis3lv02d_platform_data rx51_lis3lv02d_data = { .release_resources = lis302_release, .st_min_limits = {-32, 3, 3}, .st_max_limits = {-3, 32, 32}, - .irq2 = OMAP_GPIO_IRQ(LIS302_IRQ2_GPIO), }; #endif @@ -1030,7 +1029,6 @@ static struct i2c_board_info __initdata rx51_peripherals_i2c_board_info_3[] = { { I2C_BOARD_INFO("lis3lv02d", 0x1d), .platform_data = &rx51_lis3lv02d_data, - .irq = OMAP_GPIO_IRQ(LIS302_IRQ1_GPIO), }, #endif }; @@ -1056,6 +1054,10 @@ static int __init rx51_i2c_init(void) omap_pmic_init(1, 2200, "twl5030", INT_34XX_SYS_NIRQ, &rx51_twldata); omap_register_i2c_bus(2, 100, rx51_peripherals_i2c_board_info_2, ARRAY_SIZE(rx51_peripherals_i2c_board_info_2)); +#if defined(CONFIG_SENSORS_LIS3_I2C) || defined(CONFIG_SENSORS_LIS3_I2C_MODULE) + rx51_lis3lv02d_data.irq2 = gpio_to_irq(LIS302_IRQ2_GPIO); + rx51_peripherals_i2c_board_info_3[0].irq = gpio_to_irq(LIS302_IRQ1_GPIO); +#endif omap_register_i2c_bus(3, 400, rx51_peripherals_i2c_board_info_3, ARRAY_SIZE(rx51_peripherals_i2c_board_info_3)); return 0; -- cgit v1.2.3 From 91930652a23de0873a157aa1d9962cb878d64451 Mon Sep 17 00:00:00 2001 From: "Govindraj.R" Date: Tue, 5 Jun 2012 04:04:11 -0700 Subject: OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup The commit (bce492c0 ARM: OMAP2+: UART: Fix incorrect population of default uart pads) removed default uart pads that where getting populated and which was making rx pin wakeup capable. If uart pads were used in different mode by any other module then it would fail since the default pads took over all the uart pins forcefully. With removal of default pads the rx_pad wakeup for console uart while waking up from off mode is broken. Utilise the mux api available to probe the availability of mux pins in uart mode and probe for availability of uart pin in mux mode0 if uart is available as uart pin itself then configure rx pin as wakeup capable. This patch itself doesn't cater to all boards. Boards using uart rx wakeup mechanism should ensure the usage of omap_serial_init_port by configuring required uart ports and pass necessary mux data, till then this probing of uart pins can cater to enabling of rx pad wakeup to most of the boards. This patch can also throw some boot warning from _omap_mux_get_by_name if pin is requested for availability is not present while dynamically probing the uart pins availability such boot warnings can be addressed only when board files are patched with omap_serial_init_port calls passing the right pads needed for a given port. Discussion Threads for reference: http://www.spinics.net/lists/linux-omap/msg69859.html http://www.spinics.net/lists/linux-omap/msg68659.html Cc: Felipe Balbi Cc: Kevin Hilman Cc: Russ Dill Cc: Paul Walmsley Cc: Ameya Palande Signed-off-by: Govindraj.R [tony@atomide.com: updated to fix compile when CONFIG_OMAP_MUX is not set] Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/mux.c | 3 +- arch/arm/mach-omap2/mux.h | 11 ++++++++ arch/arm/mach-omap2/serial.c | 67 +++++++++++++++++++++++++++++++++++++++++--- 3 files changed, 75 insertions(+), 6 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index 80e55c5c9998..4b46b91cca5c 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -217,8 +217,7 @@ static int __init _omap_mux_get_by_name(struct omap_mux_partition *partition, return -ENODEV; } -static int __init -omap_mux_get_by_name(const char *muxname, +int __init omap_mux_get_by_name(const char *muxname, struct omap_mux_partition **found_partition, struct omap_mux **found_mux) { diff --git a/arch/arm/mach-omap2/mux.h b/arch/arm/mach-omap2/mux.h index 69fe060a0b75..471e62a74a16 100644 --- a/arch/arm/mach-omap2/mux.h +++ b/arch/arm/mach-omap2/mux.h @@ -59,6 +59,7 @@ #define OMAP_PIN_OFF_WAKEUPENABLE OMAP_WAKEUP_EN #define OMAP_MODE_GPIO(x) (((x) & OMAP_MUX_MODE7) == OMAP_MUX_MODE4) +#define OMAP_MODE_UART(x) (((x) & OMAP_MUX_MODE7) == OMAP_MUX_MODE0) /* Flags for omapX_mux_init */ #define OMAP_PACKAGE_MASK 0xffff @@ -225,8 +226,18 @@ omap_hwmod_mux_init(struct omap_device_pad *bpads, int nr_pads); */ void omap_hwmod_mux(struct omap_hwmod_mux_info *hmux, u8 state); +int omap_mux_get_by_name(const char *muxname, + struct omap_mux_partition **found_partition, + struct omap_mux **found_mux); #else +static inline int omap_mux_get_by_name(const char *muxname, + struct omap_mux_partition **found_partition, + struct omap_mux **found_mux) +{ + return 0; +} + static inline int omap_mux_init_gpio(int gpio, int val) { return 0; diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 292d4aaca068..c1b93c752d70 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -57,6 +57,7 @@ struct omap_uart_state { struct list_head node; struct omap_hwmod *oh; + struct omap_device_pad default_omap_uart_pads[2]; }; static LIST_HEAD(uart_list); @@ -126,11 +127,70 @@ static void omap_uart_set_smartidle(struct platform_device *pdev) {} #endif /* CONFIG_PM */ #ifdef CONFIG_OMAP_MUX -static void omap_serial_fill_default_pads(struct omap_board_data *bdata) + +#define OMAP_UART_DEFAULT_PAD_NAME_LEN 28 +static char rx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN], + tx_pad_name[OMAP_UART_DEFAULT_PAD_NAME_LEN] __initdata; + +static void __init +omap_serial_fill_uart_tx_rx_pads(struct omap_board_data *bdata, + struct omap_uart_state *uart) +{ + uart->default_omap_uart_pads[0].name = rx_pad_name; + uart->default_omap_uart_pads[0].flags = OMAP_DEVICE_PAD_REMUX | + OMAP_DEVICE_PAD_WAKEUP; + uart->default_omap_uart_pads[0].enable = OMAP_PIN_INPUT | + OMAP_MUX_MODE0; + uart->default_omap_uart_pads[0].idle = OMAP_PIN_INPUT | OMAP_MUX_MODE0; + uart->default_omap_uart_pads[1].name = tx_pad_name; + uart->default_omap_uart_pads[1].enable = OMAP_PIN_OUTPUT | + OMAP_MUX_MODE0; + bdata->pads = uart->default_omap_uart_pads; + bdata->pads_cnt = ARRAY_SIZE(uart->default_omap_uart_pads); +} + +static void __init omap_serial_check_wakeup(struct omap_board_data *bdata, + struct omap_uart_state *uart) { + struct omap_mux_partition *tx_partition = NULL, *rx_partition = NULL; + struct omap_mux *rx_mux = NULL, *tx_mux = NULL; + char *rx_fmt, *tx_fmt; + int uart_nr = bdata->id + 1; + + if (bdata->id != 2) { + rx_fmt = "uart%d_rx.uart%d_rx"; + tx_fmt = "uart%d_tx.uart%d_tx"; + } else { + rx_fmt = "uart%d_rx_irrx.uart%d_rx_irrx"; + tx_fmt = "uart%d_tx_irtx.uart%d_tx_irtx"; + } + + snprintf(rx_pad_name, OMAP_UART_DEFAULT_PAD_NAME_LEN, rx_fmt, + uart_nr, uart_nr); + snprintf(tx_pad_name, OMAP_UART_DEFAULT_PAD_NAME_LEN, tx_fmt, + uart_nr, uart_nr); + + if (omap_mux_get_by_name(rx_pad_name, &rx_partition, &rx_mux) >= 0 && + omap_mux_get_by_name + (tx_pad_name, &tx_partition, &tx_mux) >= 0) { + u16 tx_mode, rx_mode; + + tx_mode = omap_mux_read(tx_partition, tx_mux->reg_offset); + rx_mode = omap_mux_read(rx_partition, rx_mux->reg_offset); + + /* + * Check if uart is used in default tx/rx mode i.e. in mux mode0 + * if yes then configure rx pin for wake up capability + */ + if (OMAP_MODE_UART(rx_mode) && OMAP_MODE_UART(tx_mode)) + omap_serial_fill_uart_tx_rx_pads(bdata, uart); + } } #else -static void omap_serial_fill_default_pads(struct omap_board_data *bdata) {} +static void __init omap_serial_check_wakeup(struct omap_board_data *bdata, + struct omap_uart_state *uart) +{ +} #endif static char *cmdline_find_option(char *str) @@ -287,8 +347,7 @@ void __init omap_serial_board_init(struct omap_uart_port_info *info) bdata.pads = NULL; bdata.pads_cnt = 0; - if (cpu_is_omap44xx() || cpu_is_omap34xx()) - omap_serial_fill_default_pads(&bdata); + omap_serial_check_wakeup(&bdata, uart); if (!info) omap_serial_init_port(&bdata, NULL); -- cgit v1.2.3 From 00d6bfaf20e723e3f4c9aa6bc0fb6636785a0701 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 6 Jun 2012 01:42:20 -0700 Subject: ARM: OMAP3: Fix omap3_l3_block_irq warning when CONFIG_BUG is not set MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Otherwise we will get: arch/arm/mach-omap2/omap_l3_smx.c: In function ‘omap3_l3_block_irq’: arch/arm/mach-omap2/omap_l3_smx.c:156: warning: unused variable ‘address’ arch/arm/mach-omap2/omap_l3_smx.c:155: warning: unused variable ‘multi’ arch/arm/mach-omap2/omap_l3_smx.c:154: warning: unused variable ‘initid’ arch/arm/mach-omap2/omap_l3_smx.c:153: warning: unused variable ‘code’ arch/arm/mach-omap2/omap_l3_smx.c: At top level: arch/arm/mach-omap2/omap_l3_smx.c:68: warning: ‘omap3_l3_code_string’ defined but not used arch/arm/mach-omap2/omap_l3_smx.c:90: warning: ‘omap3_l3_initiator_string’ defined but not used Fix it by always showing the L3 error. Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/omap_l3_smx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/omap_l3_smx.c b/arch/arm/mach-omap2/omap_l3_smx.c index a05a62f9ee5b..acc216491b8a 100644 --- a/arch/arm/mach-omap2/omap_l3_smx.c +++ b/arch/arm/mach-omap2/omap_l3_smx.c @@ -155,10 +155,11 @@ static irqreturn_t omap3_l3_block_irq(struct omap3_l3 *l3, u8 multi = error & L3_ERROR_LOG_MULTI; u32 address = omap3_l3_decode_addr(error_addr); - WARN(true, "%s seen by %s %s at address %x\n", + pr_err("%s seen by %s %s at address %x\n", omap3_l3_code_string(code), omap3_l3_initiator_string(initid), multi ? "Multiple Errors" : "", address); + WARN_ON(1); return IRQ_HANDLED; } -- cgit v1.2.3 From febe9e02d63ed8a42e7e9c75ea16117821f90f07 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 6 Jun 2012 01:42:20 -0700 Subject: ARM: OMAP2+: Fix compile for CONFIG_TIDSPBRIDGE platform init code Commit 7f28427b (ARM: OMAP2+: Move omap_dsp_reserve_sdram_memblock() to mach-omap2) moved DSP platform init code, but failed to include memblock.h causing: arch/arm/mach-omap2/dsp.c: In function 'omap_dsp_reserve_sdram_memblock': arch/arm/mach-omap2/dsp.c:58: error: implicit declaration of function 'arm_memblock_steal' Reported-by: Russell King Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/dsp.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/dsp.c b/arch/arm/mach-omap2/dsp.c index 845309f146fe..88ffa1e645cd 100644 --- a/arch/arm/mach-omap2/dsp.c +++ b/arch/arm/mach-omap2/dsp.c @@ -20,6 +20,9 @@ #include #include + +#include + #include "cm2xxx_3xxx.h" #include "prm2xxx_3xxx.h" #ifdef CONFIG_BRIDGE_DVFS -- cgit v1.2.3 From 310018d52ec06c19dc946c2807c07c8b70e2d1a6 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 20 Jun 2012 07:18:15 -0700 Subject: ARM: OMAP2+: Fix MUSB ifdefs for platform init code Commit 62285963 (usb: musb: drop a gigantic amount of ifdeferry) got rid of a bunch of ifdefs in the MUSB code. Looks like the platform init code is still using these dropped defines though, which in many cases results the board defaulting always to host mode. Currently the situation is that USB_MUSB_HDRC is the main Kconfig option with additional USB_GADGET_MUSB_HDRC so only these two should be used to select between host and OTG mode. Fix the situation for omaps. The following users should fix the platform init code in a similar way: Dropped Kconfig option Current users USB_MUSB_OTG blackfin, davinci, not in Kconfigs USB_MUSB_PERIPHERAL davinci, not in Kconfigs USB_MUSB_HOST davinci, not in Kconfigs USB_MUSB_HDRC_HCD blackfin, not in Kconfigs USB_MUSB_OTG blackfin, not in Kconfigs Cc: Mike Frysinger Cc: Sekhar Nori Cc: linux-usb@vger.kernel.org Cc: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-n8x0.c | 6 ++---- arch/arm/mach-omap2/omap_phy_internal.c | 6 ------ arch/arm/mach-omap2/usb-musb.c | 6 ++---- 3 files changed, 4 insertions(+), 14 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c index 8ca14e88a31a..2c5d0ed75285 100644 --- a/arch/arm/mach-omap2/board-n8x0.c +++ b/arch/arm/mach-omap2/board-n8x0.c @@ -83,11 +83,9 @@ static struct musb_hdrc_config musb_config = { }; static struct musb_hdrc_platform_data tusb_data = { -#if defined(CONFIG_USB_MUSB_OTG) +#ifdef CONFIG_USB_GADGET_MUSB_HDRC .mode = MUSB_OTG, -#elif defined(CONFIG_USB_MUSB_PERIPHERAL) - .mode = MUSB_PERIPHERAL, -#else /* defined(CONFIG_USB_MUSB_HOST) */ +#else .mode = MUSB_HOST, #endif .set_power = tusb_set_power, diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c index 4c90477e6f82..d52651a05daa 100644 --- a/arch/arm/mach-omap2/omap_phy_internal.c +++ b/arch/arm/mach-omap2/omap_phy_internal.c @@ -239,21 +239,15 @@ void am35x_set_mode(u8 musb_mode) devconf2 &= ~CONF2_OTGMODE; switch (musb_mode) { -#ifdef CONFIG_USB_MUSB_HDRC_HCD case MUSB_HOST: /* Force VBUS valid, ID = 0 */ devconf2 |= CONF2_FORCE_HOST; break; -#endif -#ifdef CONFIG_USB_GADGET_MUSB_HDRC case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */ devconf2 |= CONF2_FORCE_DEVICE; break; -#endif -#ifdef CONFIG_USB_MUSB_OTG case MUSB_OTG: /* Don't override the VBUS/ID comparators */ devconf2 |= CONF2_NO_OVERRIDE; break; -#endif default: pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode); } diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index b19d1b43c12e..c4a576856661 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -41,12 +41,10 @@ static struct musb_hdrc_config musb_config = { }; static struct musb_hdrc_platform_data musb_plat = { -#ifdef CONFIG_USB_MUSB_OTG +#ifdef CONFIG_USB_GADGET_MUSB_HDRC .mode = MUSB_OTG, -#elif defined(CONFIG_USB_MUSB_HDRC_HCD) +#else .mode = MUSB_HOST, -#elif defined(CONFIG_USB_GADGET_MUSB_HDRC) - .mode = MUSB_PERIPHERAL, #endif /* .clock is set dynamically */ .config = &musb_config, -- cgit v1.2.3 From 3d09b33fecf204561e5c7126648ec05c756c631c Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 20 Jun 2012 07:18:15 -0700 Subject: ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0 Here's one more gpio_to_irq conversion that we missed earlier. Tested with n800 in gadget mode using USB_ETH. Cc: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/usb-tusb6010.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/usb-tusb6010.c b/arch/arm/mach-omap2/usb-tusb6010.c index db84a46ce7fd..805bea6edf17 100644 --- a/arch/arm/mach-omap2/usb-tusb6010.c +++ b/arch/arm/mach-omap2/usb-tusb6010.c @@ -300,7 +300,7 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data, printk(error, 3, status); return status; } - tusb_resources[2].start = irq + IH_GPIO_BASE; + tusb_resources[2].start = gpio_to_irq(irq); /* set up memory timings ... can speed them up later */ if (!ps_refclk) { -- cgit v1.2.3 From aef2b89662b8a7506846d0dc0df672d196ddf8d0 Mon Sep 17 00:00:00 2001 From: Russ Dill Date: Wed, 9 May 2012 15:15:03 -0700 Subject: ARM: OMAP: Fix Beagleboard DVI reset gpio Commit e813a55eb9c9bc6c8039fb16332cf43402125b30 ("OMAP: board-files: remove custom PD GPIO handling for DVI output") moved TFP410 chip's powerdown-gpio handling from the board files to the tfp410 driver. One gpio_request_one(powerdown-gpio, ...) was mistakenly left unremoved in the Beagle board file. This causes the tfp410 driver to fail to request the gpio on Beagle, causing the driver to fail and thus the DVI output doesn't work. This patch removes several boot errors from board-omap3beagle.c: - gpio_request: gpio--22 (DVI reset) status -22 - Unable to get DVI reset GPIO There is a combination of leftover code and revision confusion. Additionally, xM support is currently a hack. For original Beagleboard this removes the double initialization of GPIO 170, properly configures it as an output, and wraps the initialization in an if block so that xM does not attempt to request it. For Beagleboard xM it removes reference to GPIO 129 which was part of rev A1 and A2 designs, but never functioned. It then properly assigns beagle_dvi_device.reset_gpio in beagle_twl_gpio_setup and removes the hack of initializing it high. Additionally, it uses gpio_set_value_cansleep since this GPIO is connected through i2c. Unfortunately, there is no way to tell the difference between xM A2 and A3. However, GPIO 129 does not function on rev A1 and A2, and the TWL GPIO used on A3 and beyond is not used on rev A1 and A2, there are no problems created by this fix. Tested on Beagleboard-xM Rev C1 and Beagleboard Rev B4. Signed-off-by: Russ Dill Acked-by: Tomi Valkeinen Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-omap3beagle.c | 28 ++++++++++++---------------- 1 file changed, 12 insertions(+), 16 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 79c6909eeb78..580fd17208da 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -81,13 +81,13 @@ static u8 omap3_beagle_version; static struct { int mmc1_gpio_wp; int usb_pwr_level; - int reset_gpio; + int dvi_pd_gpio; int usr_button_gpio; int mmc_caps; } beagle_config = { .mmc1_gpio_wp = -EINVAL, .usb_pwr_level = GPIOF_OUT_INIT_LOW, - .reset_gpio = 129, + .dvi_pd_gpio = -EINVAL, .usr_button_gpio = 4, .mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, }; @@ -126,21 +126,21 @@ static void __init omap3_beagle_init_rev(void) printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n"); omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX; beagle_config.mmc1_gpio_wp = 29; - beagle_config.reset_gpio = 170; + beagle_config.dvi_pd_gpio = 170; beagle_config.usr_button_gpio = 7; break; case 6: printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n"); omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3; beagle_config.mmc1_gpio_wp = 23; - beagle_config.reset_gpio = 170; + beagle_config.dvi_pd_gpio = 170; beagle_config.usr_button_gpio = 7; break; case 5: printk(KERN_INFO "OMAP3 Beagle Rev: C4\n"); omap3_beagle_version = OMAP3BEAGLE_BOARD_C4; beagle_config.mmc1_gpio_wp = 23; - beagle_config.reset_gpio = 170; + beagle_config.dvi_pd_gpio = 170; beagle_config.usr_button_gpio = 7; break; case 0: @@ -274,11 +274,9 @@ static int beagle_twl_gpio_setup(struct device *dev, if (r) pr_err("%s: unable to configure nDVI_PWR_EN\n", __func__); - r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH, - "DVI_LDO_EN"); - if (r) - pr_err("%s: unable to configure DVI_LDO_EN\n", - __func__); + + beagle_config.dvi_pd_gpio = gpio + 2; + } else { /* * REVISIT: need ehci-omap hooks for external VBUS @@ -287,7 +285,7 @@ static int beagle_twl_gpio_setup(struct device *dev, if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC")) pr_err("%s: unable to configure EHCI_nOC\n", __func__); } - dvi_panel.power_down_gpio = beagle_config.reset_gpio; + dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio; gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level, "nEN_USB_PWR"); @@ -499,7 +497,7 @@ static void __init omap3_beagle_init(void) omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); omap3_beagle_init_rev(); - if (beagle_config.mmc1_gpio_wp != -EINVAL) + if (gpio_is_valid(beagle_config.mmc1_gpio_wp)) omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT); mmc[0].caps = beagle_config.mmc_caps; omap_hsmmc_init(mmc); @@ -510,15 +508,13 @@ static void __init omap3_beagle_init(void) platform_add_devices(omap3_beagle_devices, ARRAY_SIZE(omap3_beagle_devices)); + if (gpio_is_valid(beagle_config.dvi_pd_gpio)) + omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT); omap_display_init(&beagle_dss_data); omap_serial_init(); omap_sdrc_init(mt46h32m32lf6_sdrc_params, mt46h32m32lf6_sdrc_params); - omap_mux_init_gpio(170, OMAP_PIN_INPUT); - /* REVISIT leave DVI powered down until it's needed ... */ - gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD"); - usb_musb_init(NULL); usbhs_init(&usbhs_bdata); omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions, -- cgit v1.2.3 From 561038f0a8aa1de272a2ac5dad24cc8246d9f496 Mon Sep 17 00:00:00 2001 From: Djamil Elaidi Date: Sun, 17 Jun 2012 11:57:51 -0600 Subject: ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby If an IP is configured in Smart-Standby-Wakeup, when disabling wakeup feature the IP will not go back to Smart-Standby, but will remain in Smart-Standby-Wakeup. Signed-off-by: Djamil Elaidi Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/omap_hwmod.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index bf86f7e8f91f..773193670ea2 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -530,7 +530,7 @@ static int _disable_wakeup(struct omap_hwmod *oh, u32 *v) if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP) _set_slave_idlemode(oh, HWMOD_IDLEMODE_SMART, v); if (oh->class->sysc->idlemodes & MSTANDBY_SMART_WKUP) - _set_master_standbymode(oh, HWMOD_IDLEMODE_SMART_WKUP, v); + _set_master_standbymode(oh, HWMOD_IDLEMODE_SMART, v); /* XXX test pwrdm_get_wken for this hwmod's subsystem */ -- cgit v1.2.3 From 252a4c5443ec4d0bd310ae5b0d1b7f9c5b1e7f46 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Sun, 17 Jun 2012 11:57:51 -0600 Subject: ARM: OMAP4: hwmod data: fix 32k sync timer idle modes MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The 32k sync timer IP block target idle modes in the hwmod data are incorrect. The IP block does not support any smart-idle modes. Update the data to reflect the correct modes. This problem was initially identified and a diff fragment posted to the lists by Benoît Cousson . A patch description bug in the first version was also identified by Benoît. Signed-off-by: Paul Walmsley Cc: Benoît Cousson Cc: Tero Kristo --- arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index 950454a3fa31..c4c9cdd4c0cf 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -393,8 +393,7 @@ static struct omap_hwmod_class_sysconfig omap44xx_counter_sysc = { .rev_offs = 0x0000, .sysc_offs = 0x0004, .sysc_flags = SYSC_HAS_SIDLEMODE, - .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART | - SIDLE_SMART_WKUP), + .idlemodes = (SIDLE_FORCE | SIDLE_NO), .sysc_fields = &omap_hwmod_sysc_type1, }; -- cgit v1.2.3 From 9a47d32d5c4b91a4ce4c459f3b7b0290185e7578 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Sun, 17 Jun 2012 11:57:52 -0600 Subject: ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Until the OMAP4 code is converted to disable the use of the clock framework-based clockdomain enable/disable sequence, any clock used as a hwmod main_clk must have a clockdomain associated with it. This patch populates some clock structure clockdomain names to resolve the following warnings during kernel init: omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck. omap_hwmod: trace_clk_div_ck: missing clockdomain for trace_clk_div_ck. omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck. omap_hwmod: ddrphy_ck: missing clockdomain for ddrphy_ck. Signed-off-by: Paul Walmsley Cc: Rajendra Nayak Cc: Benoît Cousson --- arch/arm/mach-omap2/clock44xx_data.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock44xx_data.c b/arch/arm/mach-omap2/clock44xx_data.c index 2172f6603848..e2b701e164f6 100644 --- a/arch/arm/mach-omap2/clock44xx_data.c +++ b/arch/arm/mach-omap2/clock44xx_data.c @@ -84,6 +84,7 @@ static struct clk slimbus_clk = { static struct clk sys_32k_ck = { .name = "sys_32k_ck", + .clkdm_name = "prm_clkdm", .rate = 32768, .ops = &clkops_null, }; @@ -512,6 +513,7 @@ static struct clk ddrphy_ck = { .name = "ddrphy_ck", .parent = &dpll_core_m2_ck, .ops = &clkops_null, + .clkdm_name = "l3_emif_clkdm", .fixed_div = 2, .recalc = &omap_fixed_divisor_recalc, }; @@ -769,6 +771,7 @@ static const struct clksel dpll_mpu_m2_div[] = { static struct clk dpll_mpu_m2_ck = { .name = "dpll_mpu_m2_ck", .parent = &dpll_mpu_ck, + .clkdm_name = "cm_clkdm", .clksel = dpll_mpu_m2_div, .clksel_reg = OMAP4430_CM_DIV_M2_DPLL_MPU, .clksel_mask = OMAP4430_DPLL_CLKOUT_DIV_MASK, @@ -1149,6 +1152,7 @@ static const struct clksel l3_div_div[] = { static struct clk l3_div_ck = { .name = "l3_div_ck", .parent = &div_core_ck, + .clkdm_name = "cm_clkdm", .clksel = l3_div_div, .clksel_reg = OMAP4430_CM_CLKSEL_CORE, .clksel_mask = OMAP4430_CLKSEL_L3_MASK, @@ -2824,6 +2828,7 @@ static const struct clksel trace_clk_div_div[] = { static struct clk trace_clk_div_ck = { .name = "trace_clk_div_ck", .parent = &pmd_trace_clk_mux_ck, + .clkdm_name = "emu_sys_clkdm", .clksel = trace_clk_div_div, .clksel_reg = OMAP4430_CM_EMU_DEBUGSS_CLKCTRL, .clksel_mask = OMAP4430_CLKSEL_PMD_TRACE_CLK_MASK, -- cgit v1.2.3 From b8f15b7e1dd3638d35cfff85571df1d7ea96e35e Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Sun, 17 Jun 2012 11:57:53 -0600 Subject: ARM: OMAP2+: CM: increase the module disable timeout Increase the timeout for disabling an IP block to five milliseconds. This is to handle the usb_host_fs idle latency, which takes almost four milliseconds after a host controller reset. This is the second of two patches needed to resolve the following boot warning: omap_hwmod: usb_host_fs: _wait_target_disable failed Thanks to Sergei Shtylyov for finding an unrelated hunk in a previous version of this patch. Signed-off-by: Paul Walmsley Cc: Sergei Shtylyov Cc: Tero Kristo --- arch/arm/mach-omap2/cm.h | 11 +++++++++++ arch/arm/mach-omap2/cminst44xx.c | 4 ++-- 2 files changed, 13 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h index a7bc096bd407..f24e3f7a2bbc 100644 --- a/arch/arm/mach-omap2/cm.h +++ b/arch/arm/mach-omap2/cm.h @@ -22,4 +22,15 @@ */ #define MAX_MODULE_READY_TIME 2000 +/* + * MAX_MODULE_DISABLE_TIME: max duration in microseconds to wait for + * the PRCM to request that a module enter the inactive state in the + * case of OMAP2 & 3. In the case of OMAP4 this is the max duration + * in microseconds for the module to reach the inactive state from + * a functional state. + * XXX FSUSB on OMAP4430 takes ~4ms to idle after reset during + * kernel init. + */ +#define MAX_MODULE_DISABLE_TIME 5000 + #endif diff --git a/arch/arm/mach-omap2/cminst44xx.c b/arch/arm/mach-omap2/cminst44xx.c index 8c86d294b1a3..1a39945d9ff8 100644 --- a/arch/arm/mach-omap2/cminst44xx.c +++ b/arch/arm/mach-omap2/cminst44xx.c @@ -313,9 +313,9 @@ int omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs, u16 clkctrl_off omap_test_timeout((_clkctrl_idlest(part, inst, cdoffs, clkctrl_offs) == CLKCTRL_IDLEST_DISABLED), - MAX_MODULE_READY_TIME, i); + MAX_MODULE_DISABLE_TIME, i); - return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY; + return (i < MAX_MODULE_DISABLE_TIME) ? 0 : -EBUSY; } /** -- cgit v1.2.3 From 65e25976b75c4996c5650afadc4180db09ec7475 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Sun, 17 Jun 2012 12:00:58 -0600 Subject: ARM: OMAP2+: mux: fix sparse warning Commit bbd707acee279a61177a604822db92e8164d00db ("ARM: omap2: use machine specific hook for late init") resulted in the addition of this sparse warning: arch/arm/mach-omap2/mux.c:791:12: warning: symbol 'omap_mux_late_init' was not declared. Should it be static? Fix by including the header file containing the prototype. Signed-off-by: Paul Walmsley Cc: Shawn Guo Cc: Tony Lindgren --- arch/arm/mach-omap2/mux.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index 80e55c5c9998..d3ef99c5cad8 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -41,6 +41,7 @@ #include "control.h" #include "mux.h" #include "prm.h" +#include "common.h" #define OMAP_MUX_BASE_OFFSET 0x30 /* Offset from CTRL_BASE */ #define OMAP_MUX_BASE_SZ 0x5ca -- cgit v1.2.3 From dc57aef503859dbf724f6126c58b2e1672e215f3 Mon Sep 17 00:00:00 2001 From: Ricardo Neri Date: Thu, 21 Jun 2012 10:08:53 +0200 Subject: ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled As per the OMAP4 documentation, audio over HDMI must be transmitted in no-idle mode. This patch adds the HWMOD_SWSUP_SIDLE so that omap_hwmod uses no-idle/force-idle settings instead of smart-idle mode. This is required as the DSS interface clock is used as functional clock for the HDMI wrapper audio FIFO. If no-idle mode is not used, audio could be choppy, have bad quality or not be audible at all. Signed-off-by: Ricardo Neri [b-cousson@ti.com: Update the subject and align the .flags location with the script template] Signed-off-by: Benoit Cousson Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index c4c9cdd4c0cf..f30e861ce6d9 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -853,6 +853,11 @@ static struct omap_hwmod omap44xx_dss_hdmi_hwmod = { .name = "dss_hdmi", .class = &omap44xx_hdmi_hwmod_class, .clkdm_name = "l3_dss_clkdm", + /* + * HDMI audio requires to use no-idle mode. Hence, + * set idle mode by software. + */ + .flags = HWMOD_SWSUP_SIDLE, .mpu_irqs = omap44xx_dss_hdmi_irqs, .sdma_reqs = omap44xx_dss_hdmi_sdma_reqs, .main_clk = "dss_48mhz_clk", -- cgit v1.2.3 From bb44c30e53053c653302b53c8671c3c5ca62e881 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 26 Jun 2012 03:29:57 -0700 Subject: ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 8259573b (ARM: OMAP2+: nand: Make board_onenand_init() visible to board code) broke the build for configs with OneNAND disabled. By removing the static in the header file, it created a duplicate definition in the .c and the .h files, resuling in a build error: /work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.c:102:111: error: redefinition of 'board_onenand_init' /work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.h:56:51: note: previous definition of 'board_onenand_init' was here make[2]: *** [arch/arm/mach-omap2/board-flash.o] Error 1 make[2]: *** Waiting for unfinished jobs.... make[1]: *** [arch/arm/mach-omap2] Error 2 make: *** [sub-make] Error 2 Fix this by removing the duplicate dummy entry from the C file. Cc: Enric Balletbò i Serra Cc: Javier Martinez Canillas Signed-off-by: Kevin Hilman Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-flash.c | 5 ----- 1 file changed, 5 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-flash.c b/arch/arm/mach-omap2/board-flash.c index 70a81f900bb5..53c39d239d6e 100644 --- a/arch/arm/mach-omap2/board-flash.c +++ b/arch/arm/mach-omap2/board-flash.c @@ -97,11 +97,6 @@ __init board_onenand_init(struct mtd_partition *onenand_parts, gpmc_onenand_init(&board_onenand_data); } -#else -void -__init board_onenand_init(struct mtd_partition *nor_parts, u8 nr_parts, u8 cs) -{ -} #endif /* CONFIG_MTD_ONENAND_OMAP2 || CONFIG_MTD_ONENAND_OMAP2_MODULE */ #if defined(CONFIG_MTD_NAND_OMAP2) || \ -- cgit v1.2.3 From e90b833ee1aae64b6fca2455001323ffe29e1698 Mon Sep 17 00:00:00 2001 From: Jon Hunter Date: Mon, 25 Jun 2012 12:38:23 -0500 Subject: ARM: OMAP4470: Fix OMAP4470 boot failure OMAP4470 currently fails to boot, printing various messages such as ... omap_hwmod: mpu: cannot clk_get main_clk dpll_mpu_m2_ck omap_hwmod: mpu: cannot _init_clocks ------------[ cut here ]------------ WARNING: at arch/arm/mach-omap2/omap_hwmod.c:2062 _init+0x2a0/0x2e4() omap_hwmod: mpu: couldn't init clocks Modules linked in: [] (unwind_backtrace+0x0/0xf4) from [] (warn_slowpath_common+0x4c/0x64) [] (warn_slowpath_common+0x4c/0x64) from [] (warn_slowpath_fmt+0x30/0x40) [] (warn_slowpath_fmt+0x30/0x40) from [] (_init+0x2a0/0x2e4) [] (_init+0x2a0/0x2e4) from [] (omap_hwmod_setup_one+0x40/0x60) [] (omap_hwmod_setup_one+0x40/0x60) from [] (omap_hwmod_setup_one+0x34/0x60) [] (omap_hwmod_setup_one+0x34/0x60) from [] (omap_dm_timer_init_one+0x30/0x250) [] (omap_dm_timer_init_one+0x30/0x250) from [] (omap2_gp_clockevent_init+0x1c/0x108) [] (omap2_gp_clockevent_init+0x1c/0x108) from [] (omap4_timer_init+0x10/0x5c) [] (omap4_timer_init+0x10/0x5c) from [] (time_init+0x20/0x30) [] (time_init+0x20/0x30) from [] (start_kernel+0x1b0/0x304) [] (start_kernel+0x1b0/0x304) from [<80008044>] (0x80008044) ---[ end trace 1b75b31a2719ed1c ]--- The problem is that currently none of the clocks are being registered for OMAP4470 devices and so on boot-up no clocks can be found and the kernel panics. This fix allows the kernel to boot without failure using a simple RAMDISK file system on OMAP4470 blaze board. Per feedback from Paul and Benoit the 4470 clock data is incomplete for new modules such as the 2D graphics block that has been added to the 4470. Therefore add a warning to indicate that the clock data is incomplete. Cc: Paul Walmsley Cc: Benoit Cousson Signed-off-by: Jon Hunter [tony@atomide.com: updated comments] Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/clock44xx_data.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock44xx_data.c b/arch/arm/mach-omap2/clock44xx_data.c index e2b701e164f6..ba6f9a0a43e9 100644 --- a/arch/arm/mach-omap2/clock44xx_data.c +++ b/arch/arm/mach-omap2/clock44xx_data.c @@ -3417,9 +3417,12 @@ int __init omap4xxx_clk_init(void) if (cpu_is_omap443x()) { cpu_mask = RATE_IN_4430; cpu_clkflg = CK_443X; - } else if (cpu_is_omap446x()) { + } else if (cpu_is_omap446x() || cpu_is_omap447x()) { cpu_mask = RATE_IN_4460 | RATE_IN_4430; cpu_clkflg = CK_446X | CK_443X; + + if (cpu_is_omap447x()) + pr_warn("WARNING: OMAP4470 clock data incomplete!\n"); } else { return 0; } -- cgit v1.2.3 From 95669d788192d351890bfb16785336c2db816356 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Thu, 28 Jun 2012 10:01:31 -0700 Subject: ARM: OMAP2: Overo: init I2C before MMC to fix MMC suspend/resume failure In order for suspend/resume dependencies to work correctly, I2C has to be initialized (more specifically, registered with the driver core) before MMC. Without this, the MMC driver fails to adjust the VMMC regulator (using i2c writes) during the suspend path. Problem found testing suspend/resume on 3730/OveroSTORM platform. Signed-off-by: Kevin Hilman Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-overo.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 8fa2fc3a4c3c..779734d8ba37 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -494,8 +494,8 @@ static void __init overo_init(void) regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies)); omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); - omap_hsmmc_init(mmc); overo_i2c_init(); + omap_hsmmc_init(mmc); omap_display_init(&overo_dss_data); omap_serial_init(); omap_sdrc_init(mt46h32m32lf6_sdrc_params, -- cgit v1.2.3 From 5941b8142e9f4d7b8b99562e833067b307b3f390 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Thu, 28 Jun 2012 10:01:32 -0700 Subject: ARM: OMAP4: TWL6030: ensure sys_nirq1 is mux'd and wakeup enabled The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030 and interrupts from the PMIC are needed as wakeup sources. Ensure this pin is mux'd as input and has wakeup enabled so PMIC interupts (e.g. RTC) can be used as wakeup sources. Tested on OMAP4430/Panda. Signed-off-by: Kevin Hilman Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/twl-common.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c index 119d5a910f3a..43a979075338 100644 --- a/arch/arm/mach-omap2/twl-common.c +++ b/arch/arm/mach-omap2/twl-common.c @@ -32,6 +32,7 @@ #include "twl-common.h" #include "pm.h" #include "voltage.h" +#include "mux.h" static struct i2c_board_info __initdata pmic_i2c_board_info = { .addr = 0x48, @@ -77,6 +78,7 @@ void __init omap4_pmic_init(const char *pmic_type, struct twl6040_platform_data *twl6040_data, int twl6040_irq) { /* PMIC part*/ + omap_mux_init_signal("sys_nirq1", OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE); strncpy(omap4_i2c1_board_info[0].type, pmic_type, sizeof(omap4_i2c1_board_info[0].type)); omap4_i2c1_board_info[0].irq = OMAP44XX_IRQ_SYS_1N; -- cgit v1.2.3 From b0a70cc80e754f5ad7d83c96e005fa1d5cb83514 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Wed, 4 Jul 2012 06:55:29 -0600 Subject: ARM: OMAP4: hwmod data: temporarily comment out data for the usb_host_fs and aess IP blocks MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The OMAP4 usb_host_fs (OHCI) and AESS IP blocks require some special programming for them to enter idle. Without this programming, they will prevent the rest of the chip from entering full chip idle. To implement the idle programming cleanly, this will take some coordination between maintainers. This is likely to take some time, so it is probably best to leave this for 3.6 or 3.7. So, in the meantime, prevent these IP blocks from being registered. Later, once the appropriate support is available, this patch can be reverted. This second version comments out the IP block data since Benoît didn't like removing it. Signed-off-by: Paul Walmsley Cc: Benoît Cousson --- arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index f30e861ce6d9..0a1b24702091 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -3864,7 +3864,7 @@ static struct omap_hwmod_ocp_if omap44xx_l4_cfg__l3_main_2 = { }; /* usb_host_fs -> l3_main_2 */ -static struct omap_hwmod_ocp_if omap44xx_usb_host_fs__l3_main_2 = { +static struct omap_hwmod_ocp_if __maybe_unused omap44xx_usb_host_fs__l3_main_2 = { .master = &omap44xx_usb_host_fs_hwmod, .slave = &omap44xx_l3_main_2_hwmod, .clk = "l3_div_ck", @@ -3922,7 +3922,7 @@ static struct omap_hwmod_ocp_if omap44xx_l4_cfg__l3_main_3 = { }; /* aess -> l4_abe */ -static struct omap_hwmod_ocp_if omap44xx_aess__l4_abe = { +static struct omap_hwmod_ocp_if __maybe_unused omap44xx_aess__l4_abe = { .master = &omap44xx_aess_hwmod, .slave = &omap44xx_l4_abe_hwmod, .clk = "ocp_abe_iclk", @@ -4013,7 +4013,7 @@ static struct omap_hwmod_addr_space omap44xx_aess_addrs[] = { }; /* l4_abe -> aess */ -static struct omap_hwmod_ocp_if omap44xx_l4_abe__aess = { +static struct omap_hwmod_ocp_if __maybe_unused omap44xx_l4_abe__aess = { .master = &omap44xx_l4_abe_hwmod, .slave = &omap44xx_aess_hwmod, .clk = "ocp_abe_iclk", @@ -4031,7 +4031,7 @@ static struct omap_hwmod_addr_space omap44xx_aess_dma_addrs[] = { }; /* l4_abe -> aess (dma) */ -static struct omap_hwmod_ocp_if omap44xx_l4_abe__aess_dma = { +static struct omap_hwmod_ocp_if __maybe_unused omap44xx_l4_abe__aess_dma = { .master = &omap44xx_l4_abe_hwmod, .slave = &omap44xx_aess_hwmod, .clk = "ocp_abe_iclk", @@ -5857,7 +5857,7 @@ static struct omap_hwmod_addr_space omap44xx_usb_host_fs_addrs[] = { }; /* l4_cfg -> usb_host_fs */ -static struct omap_hwmod_ocp_if omap44xx_l4_cfg__usb_host_fs = { +static struct omap_hwmod_ocp_if __maybe_unused omap44xx_l4_cfg__usb_host_fs = { .master = &omap44xx_l4_cfg_hwmod, .slave = &omap44xx_usb_host_fs_hwmod, .clk = "l4_div_ck", @@ -6014,13 +6014,13 @@ static struct omap_hwmod_ocp_if *omap44xx_hwmod_ocp_ifs[] __initdata = { &omap44xx_iva__l3_main_2, &omap44xx_l3_main_1__l3_main_2, &omap44xx_l4_cfg__l3_main_2, - &omap44xx_usb_host_fs__l3_main_2, + /* &omap44xx_usb_host_fs__l3_main_2, */ &omap44xx_usb_host_hs__l3_main_2, &omap44xx_usb_otg_hs__l3_main_2, &omap44xx_l3_main_1__l3_main_3, &omap44xx_l3_main_2__l3_main_3, &omap44xx_l4_cfg__l3_main_3, - &omap44xx_aess__l4_abe, + /* &omap44xx_aess__l4_abe, */ &omap44xx_dsp__l4_abe, &omap44xx_l3_main_1__l4_abe, &omap44xx_mpu__l4_abe, @@ -6029,8 +6029,8 @@ static struct omap_hwmod_ocp_if *omap44xx_hwmod_ocp_ifs[] __initdata = { &omap44xx_l4_cfg__l4_wkup, &omap44xx_mpu__mpu_private, &omap44xx_l4_cfg__ocp_wp_noc, - &omap44xx_l4_abe__aess, - &omap44xx_l4_abe__aess_dma, + /* &omap44xx_l4_abe__aess, */ + /* &omap44xx_l4_abe__aess_dma, */ &omap44xx_l3_main_2__c2c, &omap44xx_l4_wkup__counter_32k, &omap44xx_l4_cfg__ctrl_module_core, @@ -6136,7 +6136,7 @@ static struct omap_hwmod_ocp_if *omap44xx_hwmod_ocp_ifs[] __initdata = { &omap44xx_l4_per__uart2, &omap44xx_l4_per__uart3, &omap44xx_l4_per__uart4, - &omap44xx_l4_cfg__usb_host_fs, + /* &omap44xx_l4_cfg__usb_host_fs, */ &omap44xx_l4_cfg__usb_host_hs, &omap44xx_l4_cfg__usb_otg_hs, &omap44xx_l4_cfg__usb_tll_hs, -- cgit v1.2.3 From d7a0b5133f6b1d53d693b9b9873e64e3c8f0db0e Mon Sep 17 00:00:00 2001 From: Benoit Cousson Date: Wed, 4 Jul 2012 06:55:29 -0600 Subject: ARM: OMAP2+: hwmod data: Fix wrong McBSP clock alias on OMAP4 The commit 503d0ea24d1d3dd3db95e5e0edd693da7a2a23eb ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks added a wrong "prcm_clk" alias for PRCM clock whereas the McBSP driver and previous OMAPs are using "prcm_fck". It thus lead to the following warning. [ 47.409729] omap-mcbsp: clks: could not clk_get() prcm_fck Fix that by changing the opt_clk role to prcm_fck. Reported-by: Misael Lopez Cruz Signed-off-by: Benoit Cousson Cc: Peter Ujfalusi Tested-by: Sebastien Guiriec Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index 0a1b24702091..b7bcba5221ba 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -1928,7 +1928,7 @@ static struct omap_hwmod_dma_info omap44xx_mcbsp1_sdma_reqs[] = { static struct omap_hwmod_opt_clk mcbsp1_opt_clks[] = { { .role = "pad_fck", .clk = "pad_clks_ck" }, - { .role = "prcm_clk", .clk = "mcbsp1_sync_mux_ck" }, + { .role = "prcm_fck", .clk = "mcbsp1_sync_mux_ck" }, }; static struct omap_hwmod omap44xx_mcbsp1_hwmod = { @@ -1963,7 +1963,7 @@ static struct omap_hwmod_dma_info omap44xx_mcbsp2_sdma_reqs[] = { static struct omap_hwmod_opt_clk mcbsp2_opt_clks[] = { { .role = "pad_fck", .clk = "pad_clks_ck" }, - { .role = "prcm_clk", .clk = "mcbsp2_sync_mux_ck" }, + { .role = "prcm_fck", .clk = "mcbsp2_sync_mux_ck" }, }; static struct omap_hwmod omap44xx_mcbsp2_hwmod = { @@ -1998,7 +1998,7 @@ static struct omap_hwmod_dma_info omap44xx_mcbsp3_sdma_reqs[] = { static struct omap_hwmod_opt_clk mcbsp3_opt_clks[] = { { .role = "pad_fck", .clk = "pad_clks_ck" }, - { .role = "prcm_clk", .clk = "mcbsp3_sync_mux_ck" }, + { .role = "prcm_fck", .clk = "mcbsp3_sync_mux_ck" }, }; static struct omap_hwmod omap44xx_mcbsp3_hwmod = { @@ -2033,7 +2033,7 @@ static struct omap_hwmod_dma_info omap44xx_mcbsp4_sdma_reqs[] = { static struct omap_hwmod_opt_clk mcbsp4_opt_clks[] = { { .role = "pad_fck", .clk = "pad_clks_ck" }, - { .role = "prcm_clk", .clk = "mcbsp4_sync_mux_ck" }, + { .role = "prcm_fck", .clk = "mcbsp4_sync_mux_ck" }, }; static struct omap_hwmod omap44xx_mcbsp4_hwmod = { -- cgit v1.2.3