From 0ea001d3b43cc9d387c093ae205c4228cd88a886 Mon Sep 17 00:00:00 2001 From: Chris Zhong Date: Wed, 15 Apr 2015 13:57:11 +0800 Subject: ARM: rockchip: disable dapswjdp during suspend Reset dapswjdp is controlled by JTAG_TRSTN, if the iomux of this pin is not "jtag_trstn". the AP would think this pin is always high, so it can not reset before resume. When system resume, but the dapswjdp is not in a default state, it may Access some illegal address, it cause system crash during resume. Let's disable this jtag function by clear the dapdeviceen bit, it prohibit the dapswjdp to access memory and registers. This bit would be enable in MASKROM, so we need clear it in suspend everytime. Signed-off-by: Chris Zhong Reviewed-by: Doug Anderson Signed-off-by: Heiko Stuebner --- arch/arm/mach-rockchip/pm.c | 7 +++++++ arch/arm/mach-rockchip/pm.h | 4 ++++ 2 files changed, 11 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-rockchip/pm.c b/arch/arm/mach-rockchip/pm.c index b07d88602073..b0dcbe28f78c 100644 --- a/arch/arm/mach-rockchip/pm.c +++ b/arch/arm/mach-rockchip/pm.c @@ -83,6 +83,13 @@ static void rk3288_slp_mode_set(int level) SGRF_PCLK_WDT_GATE | SGRF_FAST_BOOT_EN | SGRF_PCLK_WDT_GATE_WRITE | SGRF_FAST_BOOT_EN_WRITE); + /* + * The dapswjdp can not auto reset before resume, that cause it may + * access some illegal address during resume. Let's disable it before + * suspend, and the MASKROM will enable it back. + */ + regmap_write(sgrf_regmap, RK3288_SGRF_CPU_CON0, SGRF_DAPDEVICEEN_WRITE); + /* booting address of resuming system is from this register value */ regmap_write(sgrf_regmap, RK3288_SGRF_FAST_BOOT_ADDR, rk3288_bootram_phy); diff --git a/arch/arm/mach-rockchip/pm.h b/arch/arm/mach-rockchip/pm.h index 03ff31d8282d..3e8d39c0c3d5 100644 --- a/arch/arm/mach-rockchip/pm.h +++ b/arch/arm/mach-rockchip/pm.h @@ -55,6 +55,10 @@ static inline void rockchip_suspend_init(void) #define SGRF_FAST_BOOT_EN BIT(8) #define SGRF_FAST_BOOT_EN_WRITE BIT(24) +#define RK3288_SGRF_CPU_CON0 (0x40) +#define SGRF_DAPDEVICEEN BIT(0) +#define SGRF_DAPDEVICEEN_WRITE BIT(16) + #define RK3288_CRU_MODE_CON 0x50 #define RK3288_CRU_SEL0_CON 0x60 #define RK3288_CRU_SEL1_CON 0x64 -- cgit v1.2.3 From b403125d3bbf8046c1186e1a49cb17bb5551db14 Mon Sep 17 00:00:00 2001 From: Chris Zhong Date: Sun, 22 Mar 2015 00:04:51 +0800 Subject: ARM: rockchip: fix undefined instruction of reset_ctrl_regs Sometimes the debug module may not work well after resume, since it has not been correctly reset when wakeup from suspend. That cause system crash during reusme, and a 'undefined instruction' is displayed on the console. Set the GRF_FORCE_JTAG bit of RK3288_GRF_SOC_CON0 can ensure that debug modul is reset. And we can change the value of RK3288_GRF_SOC_CON0 back when system resume. Signed-off-by: Chris Zhong Tested-by: Caesar Wang Reviewed-by: Douglas Anderson According to discussions, there does not seem a better solution available. Please also see the potential security implication described in the comment inline in the code. Signed-off-by: Heiko Stuebner --- arch/arm/mach-rockchip/pm.c | 26 ++++++++++++++++++++++++++ arch/arm/mach-rockchip/pm.h | 4 ++++ 2 files changed, 30 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-rockchip/pm.c b/arch/arm/mach-rockchip/pm.c index b0dcbe28f78c..22812fe06460 100644 --- a/arch/arm/mach-rockchip/pm.c +++ b/arch/arm/mach-rockchip/pm.c @@ -44,9 +44,11 @@ static void __iomem *rk3288_bootram_base; static phys_addr_t rk3288_bootram_phy; static struct regmap *pmu_regmap; +static struct regmap *grf_regmap; static struct regmap *sgrf_regmap; static u32 rk3288_pmu_pwr_mode_con; +static u32 rk3288_grf_soc_con0; static u32 rk3288_sgrf_soc_con0; static inline u32 rk3288_l2_config(void) @@ -70,11 +72,25 @@ static void rk3288_slp_mode_set(int level) { u32 mode_set, mode_set1; + regmap_read(grf_regmap, RK3288_GRF_SOC_CON0, &rk3288_grf_soc_con0); + regmap_read(sgrf_regmap, RK3288_SGRF_SOC_CON0, &rk3288_sgrf_soc_con0); regmap_read(pmu_regmap, RK3288_PMU_PWRMODE_CON, &rk3288_pmu_pwr_mode_con); + /* + * We need set this bit GRF_FORCE_JTAG here, for the debug module, + * otherwise, it may become inaccessible after resume. + * This creates a potential security issue, as the sdmmc pins may + * accept jtag data for a short time during resume if no card is + * inserted. + * But this is of course also true for the regular boot, before we + * turn of the jtag/sdmmc autodetect. + */ + regmap_write(grf_regmap, RK3288_GRF_SOC_CON0, GRF_FORCE_JTAG | + GRF_FORCE_JTAG_WRITE); + /* * SGRF_FAST_BOOT_EN - system to boot from FAST_BOOT_ADDR * PCLK_WDT_GATE - disable WDT during suspend. @@ -135,6 +151,9 @@ static void rk3288_slp_mode_set_resume(void) regmap_write(sgrf_regmap, RK3288_SGRF_SOC_CON0, rk3288_sgrf_soc_con0 | SGRF_PCLK_WDT_GATE_WRITE | SGRF_FAST_BOOT_EN_WRITE); + + regmap_write(grf_regmap, RK3288_GRF_SOC_CON0, rk3288_grf_soc_con0 | + GRF_FORCE_JTAG_WRITE); } static int rockchip_lpmode_enter(unsigned long arg) @@ -193,6 +212,13 @@ static int rk3288_suspend_init(struct device_node *np) return PTR_ERR(pmu_regmap); } + grf_regmap = syscon_regmap_lookup_by_compatible( + "rockchip,rk3288-grf"); + if (IS_ERR(grf_regmap)) { + pr_err("%s: could not find grf regmap\n", __func__); + return PTR_ERR(pmu_regmap); + } + sram_np = of_find_compatible_node(NULL, NULL, "rockchip,rk3288-pmu-sram"); if (!sram_np) { diff --git a/arch/arm/mach-rockchip/pm.h b/arch/arm/mach-rockchip/pm.h index 3e8d39c0c3d5..f8a747bc1437 100644 --- a/arch/arm/mach-rockchip/pm.h +++ b/arch/arm/mach-rockchip/pm.h @@ -48,6 +48,10 @@ static inline void rockchip_suspend_init(void) #define RK3288_PMU_WAKEUP_RST_CLR_CNT 0x44 #define RK3288_PMU_PWRMODE_CON1 0x90 +#define RK3288_GRF_SOC_CON0 0x244 +#define GRF_FORCE_JTAG BIT(12) +#define GRF_FORCE_JTAG_WRITE BIT(28) + #define RK3288_SGRF_SOC_CON0 (0x0000) #define RK3288_SGRF_FAST_BOOT_ADDR (0x0120) #define SGRF_PCLK_WDT_GATE BIT(6) -- cgit v1.2.3 From 2a9fe3ca84afff6259820c4f62e579f41476becc Mon Sep 17 00:00:00 2001 From: Heiko Stuebner Date: Tue, 20 Jan 2015 23:47:30 +0100 Subject: rockchip: make sure timer7 is enabled on rk3288 platforms timer7 supplies the architected timer and thus as has to run when the system clocksource and clockevents drivers are registered. While it should be the responsibility of the bootloader to do this, and there exists a fix in a community u-boot, all u-boot based systems that actually shipped have the mentioned issue. Therefore to not require every developer to update their u-boot, add a snippet for this, enabling the timer early in the kernel. Signed-off-by: Heiko Stuebner --- arch/arm/mach-rockchip/rockchip.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-rockchip/rockchip.c b/arch/arm/mach-rockchip/rockchip.c index d360ec044b66..b6cf3b449428 100644 --- a/arch/arm/mach-rockchip/rockchip.c +++ b/arch/arm/mach-rockchip/rockchip.c @@ -30,11 +30,30 @@ #include "pm.h" #define RK3288_GRF_SOC_CON0 0x244 +#define RK3288_TIMER6_7_PHYS 0xff810000 static void __init rockchip_timer_init(void) { if (of_machine_is_compatible("rockchip,rk3288")) { struct regmap *grf; + void __iomem *reg_base; + + /* + * Most/all uboot versions for rk3288 don't enable timer7 + * which is needed for the architected timer to work. + * So make sure it is running during early boot. + */ + reg_base = ioremap(RK3288_TIMER6_7_PHYS, SZ_16K); + if (reg_base) { + writel(0, reg_base + 0x30); + writel(0xffffffff, reg_base + 0x20); + writel(0xffffffff, reg_base + 0x24); + writel(1, reg_base + 0x30); + dsb(); + iounmap(reg_base); + } else { + pr_err("rockchip: could not map timer7 registers\n"); + } /* * Disable auto jtag/sdmmc switching that causes issues -- cgit v1.2.3 From 53d2669844263fd5fdc70f0eb6a2eb8a21086d8e Mon Sep 17 00:00:00 2001 From: Ulf Hansson Date: Mon, 20 Apr 2015 16:02:31 +0200 Subject: ARM: ux500: Move GPIO regulator for SD-card into board DTSs The GPIO regulator for the SD-card isn't a ux500 SOC configuration, but instead it's specific to the board. Move the definition of it, into the board DTSs. Fixes: c94a4ab7af3f ("ARM: ux500: Disable the MMCI gpio-regulator by default") Signed-off-by: Ulf Hansson Reviewed-by: Bjorn Andersson Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-dbx5x0.dtsi | 17 ----------------- arch/arm/boot/dts/ste-href.dtsi | 17 +++++++++++++++++ arch/arm/boot/dts/ste-snowball.dts | 15 +++++++++++++++ 3 files changed, 32 insertions(+), 17 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi index bfd3f1c734b8..2201cd5da3bb 100644 --- a/arch/arm/boot/dts/ste-dbx5x0.dtsi +++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi @@ -1017,23 +1017,6 @@ status = "disabled"; }; - vmmci: regulator-gpio { - compatible = "regulator-gpio"; - - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2900000>; - regulator-name = "mmci-reg"; - regulator-type = "voltage"; - - startup-delay-us = <100>; - enable-active-high; - - states = <1800000 0x1 - 2900000 0x0>; - - status = "disabled"; - }; - mcde@a0350000 { compatible = "stericsson,mcde"; reg = <0xa0350000 0x1000>, /* MCDE */ diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi index bf8f0eddc2c0..8cf499ad31a5 100644 --- a/arch/arm/boot/dts/ste-href.dtsi +++ b/arch/arm/boot/dts/ste-href.dtsi @@ -111,6 +111,23 @@ pinctrl-1 = <&i2c3_sleep_mode>; }; + vmmci: regulator-gpio { + compatible = "regulator-gpio"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + enable-active-high; + + states = <1800000 0x1 + 2900000 0x0>; + + status = "disabled"; + }; + // External Micro SD slot sdi0_per1@80126000 { arm,primecell-periphid = <0x10480180>; diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts index 206826a855c0..65a7f630af82 100644 --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -146,8 +146,23 @@ }; vmmci: regulator-gpio { + compatible = "regulator-gpio"; + gpios = <&gpio7 4 0x4>; enable-gpio = <&gpio6 25 0x4>; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + enable-active-high; + + states = <1800000 0x1 + 2900000 0x0>; + + status = "disabled"; }; // External Micro SD slot -- cgit v1.2.3 From f9a8c3914ba85f19c3360b19612d77c47adb8942 Mon Sep 17 00:00:00 2001 From: Ulf Hansson Date: Mon, 20 Apr 2015 16:02:32 +0200 Subject: ARM: ux500: Enable GPIO regulator for SD-card for HREF boards Fixes: c94a4ab7af3f ("ARM: ux500: Disable the MMCI gpio-regulator by default") Signed-off-by: Ulf Hansson Reviewed-by: Bjorn Andersson Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-href.dtsi | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi index 8cf499ad31a5..744c1e3a744d 100644 --- a/arch/arm/boot/dts/ste-href.dtsi +++ b/arch/arm/boot/dts/ste-href.dtsi @@ -124,8 +124,6 @@ states = <1800000 0x1 2900000 0x0>; - - status = "disabled"; }; // External Micro SD slot -- cgit v1.2.3 From 11133db7a836b0cb411faa048f07a38e994d1382 Mon Sep 17 00:00:00 2001 From: Ulf Hansson Date: Mon, 20 Apr 2015 16:02:33 +0200 Subject: ARM: ux500: Enable GPIO regulator for SD-card for snowball Fixes: c94a4ab7af3f ("ARM: ux500: Disable the MMCI gpio-regulator by default") Signed-off-by: Ulf Hansson Reviewed-by: Bjorn Andersson Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-snowball.dts | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts index 65a7f630af82..1bc84ebdccaa 100644 --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -161,8 +161,6 @@ states = <1800000 0x1 2900000 0x0>; - - status = "disabled"; }; // External Micro SD slot -- cgit v1.2.3 From 750e30d4076ae5e02ad13a376e96c95a2627742c Mon Sep 17 00:00:00 2001 From: Gregory CLEMENT Date: Tue, 14 Apr 2015 11:50:13 +0200 Subject: ARM: mvebu: armada-xp-openblocks-ax3-4: Disable internal RTC There is no crystal connected to the internal RTC on the Open Block AX3. So let's disable it in order to prevent the kernel probing the driver uselessly. Eventually this patches removes the following warning message from the boot log: "rtc-mv d0010300.rtc: internal RTC not ticking" Acked-by: Andrew Lunn Signed-off-by: Gregory CLEMENT Cc: # v3.8 + --- arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts index e3b08fb959e5..990e8a2100f0 100644 --- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts @@ -105,6 +105,10 @@ }; internal-regs { + rtc@10300 { + /* No crystal connected to the internal RTC */ + status = "disabled"; + }; serial@12000 { status = "okay"; }; -- cgit v1.2.3 From cfe8c59762244251fd9a5e281d48808095ff4090 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Tue, 14 Apr 2015 11:05:04 -0300 Subject: ARM: dts: imx23-olinuxino: Fix polarity of LED GPIO On imx23-olinuxino the LED turns on when level logic high is aplied to GPIO2_1. Fix the gpios property accordingly. Fixes: b34aa1850244 ("ARM: dts: imx23-olinuxino: Remove unneeded "default-on"") Reported-by: Stefan Wahren Signed-off-by: Fabio Estevam Tested-by: Stefan Wahren Cc: stable@vger.kernel.org Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx23-olinuxino.dts | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts index 7e6eef2488e8..839a3b96910d 100644 --- a/arch/arm/boot/dts/imx23-olinuxino.dts +++ b/arch/arm/boot/dts/imx23-olinuxino.dts @@ -12,6 +12,7 @@ */ /dts-v1/; +#include #include "imx23.dtsi" / { @@ -122,7 +123,7 @@ user { label = "green"; - gpios = <&gpio2 1 1>; + gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>; }; }; }; -- cgit v1.2.3 From 0fdebe1a2f4d3a8fc03754022fabf8ba95e131a3 Mon Sep 17 00:00:00 2001 From: Stefan Wahren Date: Tue, 14 Apr 2015 20:37:26 +0000 Subject: ARM: dts: imx23-olinuxino: Fix dr_mode of usb0 The dr_mode of usb0 on imx233-olinuxino is left to default "otg". Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the same pin as USB_OTG_ID it's possible to disable USB host by LED toggling: echo 0 > /sys/class/leds/green/brightness [ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1 [ 1068.890000] usb usb1: USB disconnect, device number 1 [ 1068.920000] usb 1-1: USB disconnect, device number 2 [ 1068.920000] usb 1-1.1: USB disconnect, device number 3 [ 1069.070000] usb 1-1.2: USB disconnect, device number 4 [ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered [ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11 This patch fixes the issue by setting dr_mode to "host" in the dts file. Reported-by: Harald Geyer Signed-off-by: Stefan Wahren Reviewed-by: Fabio Estevam Reviewed-by: Marek Vasut Acked-by: Peter Chen Fixes: b49312948285 ("ARM: dts: imx23-olinuxino: Add USB host support") Cc: stable@vger.kernel.org Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx23-olinuxino.dts | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts index 839a3b96910d..82045398bf1f 100644 --- a/arch/arm/boot/dts/imx23-olinuxino.dts +++ b/arch/arm/boot/dts/imx23-olinuxino.dts @@ -94,6 +94,7 @@ ahb@80080000 { usb0: usb@80080000 { + dr_mode = "host"; vbus-supply = <®_usb0_vbus>; status = "okay"; }; -- cgit v1.2.3 From 61b8c7b58450846b63b35e90866d2eb4fde44834 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Mon, 20 Apr 2015 15:51:38 +0200 Subject: ARM: mach-imx: devices: platform-sdhci-esdhc-imx: fix broken email address My Pengutronix address is not valid anymore, redirect people to the Pengutronix kernel team. Reported-by: Harald Geyer Signed-off-by: Wolfram Sang Acked-by: Robert Schwebel Signed-off-by: Shawn Guo --- arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c b/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c index fb8d4a2ad48c..a5edd7d60266 100644 --- a/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c +++ b/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c @@ -1,5 +1,5 @@ /* - * Copyright (C) 2010 Pengutronix, Wolfram Sang + * Copyright (C) 2010 Pengutronix, Wolfram Sang * * This program is free software; you can redistribute it and/or modify it under * the terms of the GNU General Public License version 2 as published by the -- cgit v1.2.3 From 7f8d49dcc66a3dd3a8fc3078330b8fb9e616ad3f Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Tue, 21 Apr 2015 15:59:53 +0200 Subject: ARM: dts: imx6: phyFLEX: USB VBUS control is active-high The fixed-regulator bindings require a separate property enable-active-high, the standard gpio phandle property polarity setting is ignored. Signed-off-by: Philipp Zabel Fixes: 4fe69a934b1f ("ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo") Cc: stable@vger.kernel.org Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi index 19cc269a08d4..1ce6133b67f5 100644 --- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi +++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi @@ -31,6 +31,7 @@ regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&gpio4 15 0>; + enable-active-high; }; reg_usb_h1_vbus: regulator@1 { @@ -40,6 +41,7 @@ regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&gpio1 0 0>; + enable-active-high; }; }; -- cgit v1.2.3 From f90d3f0d0a11fa77918fd5497cb616dd2faa8431 Mon Sep 17 00:00:00 2001 From: Markus Pargmann Date: Fri, 24 Apr 2015 09:27:33 +0200 Subject: ARM: dts: imx25: Add #pwm-cells to pwm4 The property '#pwm-cells' is currently missing. It is not possible to use pwm4 without this property. Signed-off-by: Markus Pargmann Fixes: 5658a68fb578 ("ARM i.MX25: Add devicetree") Cc: Reviewed-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx25.dtsi | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi index e4d3aecc4ed2..677f81d9dcd5 100644 --- a/arch/arm/boot/dts/imx25.dtsi +++ b/arch/arm/boot/dts/imx25.dtsi @@ -428,6 +428,7 @@ pwm4: pwm@53fc8000 { compatible = "fsl,imx25-pwm", "fsl,imx27-pwm"; + #pwm-cells = <2>; reg = <0x53fc8000 0x4000>; clocks = <&clks 108>, <&clks 52>; clock-names = "ipg", "per"; -- cgit v1.2.3 From 4ada77e37a773168fea484899201e272ab44ba8b Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Fri, 24 Apr 2015 13:29:47 +0200 Subject: ARM: dts: imx28: Fix AUART4 TX-DMA interrupt name Fix a typo in the TX DMA interrupt name for AUART4. This patch makes AUART4 operational again. Signed-off-by: Marek Vasut Fixes: f30fb03d4d3a ("ARM: dts: add generic DMA device tree binding for mxs-dma") Cc: stable@vger.kernel.org Acked-by: Stefan Wahren Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 25e25f82fbae..4e073e854742 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -913,7 +913,7 @@ 80 81 68 69 70 71 72 73 74 75 76 77>; - interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty", + interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty", "saif0", "saif1", "i2c0", "i2c1", "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx", "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx"; -- cgit v1.2.3 From 68ce9a1f24b8e8894955032a4af74998315be9fe Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Tue, 28 Apr 2015 09:05:21 +0800 Subject: ARM: dts: imx6qdl-sabreauto: remove pinctrl-assert-gpios The pinctrl-assert-gpios is an invalid pinctrl property. It was probably sneaked from vendor tree. Remove it. Fixes: 4e18a2243a87 ("ARM: imx6qdl-sabreauto.dtsi: add max7310 support") Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi index 46b2fed7c319..3b24b12651b2 100644 --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi @@ -185,7 +185,6 @@ &i2c3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c3>; - pinctrl-assert-gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; status = "okay"; max7310_a: gpio@30 { -- cgit v1.2.3 From aa8d6b73ea33c2167c543663ab66039ec94d58f1 Mon Sep 17 00:00:00 2001 From: Robert Jarzmik Date: Fri, 24 Apr 2015 22:22:19 +0200 Subject: ARM: pxa: pxa_cplds: add lubbock and mainstone IO Historically, this support was in arch/arm/mach-pxa/lubbock.c and arch/arm/mach-pxa/mainstone.c. When gpio-pxa was moved to drivers/pxa, it became a driver, and its initialization and probing happened at postcore initcall. The lubbock code used to install the chained lubbock interrupt handler at init_irq() time. The consequence of the gpio-pxa change is that the installed chained irq handler lubbock_irq_handler() was overwritten in pxa_gpio_probe(_dt)(), removing : - the handler - the falling edge detection setting of GPIO0, which revealed the interrupt request from the lubbock IO board. As a fix, move the gpio0 chained handler setup to a place where we have the guarantee that pxa_gpio_probe() was called before, so that lubbock handler becomes the true IRQ chained handler of GPIO0, demuxing the lubbock IO board interrupts. This patch moves all that handling to a mfd driver. It's only purpose for the time being is the interrupt handling, but in the future it should encompass all the motherboard CPLDs handling : - leds - switches - hexleds The same logic applies to mainstone board. Fixes: 157d2644cb0c ("ARM: pxa: change gpio to platform device") Signed-off-by: Robert Jarzmik Acked-by: Arnd Bergmann --- arch/arm/mach-pxa/Kconfig | 9 ++ arch/arm/mach-pxa/Makefile | 1 + arch/arm/mach-pxa/pxa_cplds_irqs.c | 200 +++++++++++++++++++++++++++++++++++++ 3 files changed, 210 insertions(+) create mode 100644 arch/arm/mach-pxa/pxa_cplds_irqs.c (limited to 'arch') diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index 8896e71586f5..f09683687963 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -691,4 +691,13 @@ config SHARPSL_PM_MAX1111 config PXA310_ULPI bool +config PXA_SYSTEMS_CPLDS + tristate "Motherboard cplds" + default ARCH_LUBBOCK || MACH_MAINSTONE + help + This driver supports the Lubbock and Mainstone multifunction chip + found on the pxa25x development platform system (Lubbock) and pxa27x + development platform system (Mainstone). This IO board supports the + interrupts handling, ethernet controller, flash chips, etc ... + endif diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile index eb0bf7678a99..4087d334ecdf 100644 --- a/arch/arm/mach-pxa/Makefile +++ b/arch/arm/mach-pxa/Makefile @@ -90,4 +90,5 @@ obj-$(CONFIG_MACH_RAUMFELD_CONNECTOR) += raumfeld.o obj-$(CONFIG_MACH_RAUMFELD_SPEAKER) += raumfeld.o obj-$(CONFIG_MACH_ZIPIT2) += z2.o +obj-$(CONFIG_PXA_SYSTEMS_CPLDS) += pxa_cplds_irqs.o obj-$(CONFIG_TOSA_BT) += tosa-bt.o diff --git a/arch/arm/mach-pxa/pxa_cplds_irqs.c b/arch/arm/mach-pxa/pxa_cplds_irqs.c new file mode 100644 index 000000000000..f1aeb54fabe3 --- /dev/null +++ b/arch/arm/mach-pxa/pxa_cplds_irqs.c @@ -0,0 +1,200 @@ +/* + * Intel Reference Systems cplds + * + * Copyright (C) 2014 Robert Jarzmik + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Cplds motherboard driver, supporting lubbock and mainstone SoC board. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define FPGA_IRQ_MASK_EN 0x0 +#define FPGA_IRQ_SET_CLR 0x10 + +#define CPLDS_NB_IRQ 32 + +struct cplds { + void __iomem *base; + int irq; + unsigned int irq_mask; + struct gpio_desc *gpio0; + struct irq_domain *irqdomain; +}; + +static irqreturn_t cplds_irq_handler(int in_irq, void *d) +{ + struct cplds *fpga = d; + unsigned long pending; + unsigned int bit; + + pending = readl(fpga->base + FPGA_IRQ_SET_CLR) & fpga->irq_mask; + for_each_set_bit(bit, &pending, CPLDS_NB_IRQ) + generic_handle_irq(irq_find_mapping(fpga->irqdomain, bit)); + + return IRQ_HANDLED; +} + +static void cplds_irq_mask_ack(struct irq_data *d) +{ + struct cplds *fpga = irq_data_get_irq_chip_data(d); + unsigned int cplds_irq = irqd_to_hwirq(d); + unsigned int set, bit = BIT(cplds_irq); + + fpga->irq_mask &= ~bit; + writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN); + set = readl(fpga->base + FPGA_IRQ_SET_CLR); + writel(set & ~bit, fpga->base + FPGA_IRQ_SET_CLR); +} + +static void cplds_irq_unmask(struct irq_data *d) +{ + struct cplds *fpga = irq_data_get_irq_chip_data(d); + unsigned int cplds_irq = irqd_to_hwirq(d); + unsigned int bit = BIT(cplds_irq); + + fpga->irq_mask |= bit; + writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN); +} + +static struct irq_chip cplds_irq_chip = { + .name = "pxa_cplds", + .irq_mask_ack = cplds_irq_mask_ack, + .irq_unmask = cplds_irq_unmask, + .flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE, +}; + +static int cplds_irq_domain_map(struct irq_domain *d, unsigned int irq, + irq_hw_number_t hwirq) +{ + struct cplds *fpga = d->host_data; + + irq_set_chip_and_handler(irq, &cplds_irq_chip, handle_level_irq); + irq_set_chip_data(irq, fpga); + + return 0; +} + +static const struct irq_domain_ops cplds_irq_domain_ops = { + .xlate = irq_domain_xlate_twocell, + .map = cplds_irq_domain_map, +}; + +static int cplds_resume(struct platform_device *pdev) +{ + struct cplds *fpga = platform_get_drvdata(pdev); + + writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN); + + return 0; +} + +static int cplds_probe(struct platform_device *pdev) +{ + struct resource *res; + struct cplds *fpga; + int ret; + unsigned int base_irq = 0; + unsigned long irqflags = 0; + + fpga = devm_kzalloc(&pdev->dev, sizeof(*fpga), GFP_KERNEL); + if (!fpga) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (res) { + fpga->irq = (unsigned int)res->start; + irqflags = res->flags; + } + if (!fpga->irq) + return -ENODEV; + + base_irq = platform_get_irq(pdev, 1); + if (base_irq < 0) + base_irq = 0; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + fpga->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(fpga->base)) + return PTR_ERR(fpga->base); + + platform_set_drvdata(pdev, fpga); + + writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN); + writel(0, fpga->base + FPGA_IRQ_SET_CLR); + + ret = devm_request_irq(&pdev->dev, fpga->irq, cplds_irq_handler, + irqflags, dev_name(&pdev->dev), fpga); + if (ret == -ENOSYS) + return -EPROBE_DEFER; + + if (ret) { + dev_err(&pdev->dev, "couldn't request main irq%d: %d\n", + fpga->irq, ret); + return ret; + } + + irq_set_irq_wake(fpga->irq, 1); + fpga->irqdomain = irq_domain_add_linear(pdev->dev.of_node, + CPLDS_NB_IRQ, + &cplds_irq_domain_ops, fpga); + if (!fpga->irqdomain) + return -ENODEV; + + if (base_irq) { + ret = irq_create_strict_mappings(fpga->irqdomain, base_irq, 0, + CPLDS_NB_IRQ); + if (ret) { + dev_err(&pdev->dev, "couldn't create the irq mapping %d..%d\n", + base_irq, base_irq + CPLDS_NB_IRQ); + return ret; + } + } + + return 0; +} + +static int cplds_remove(struct platform_device *pdev) +{ + struct cplds *fpga = platform_get_drvdata(pdev); + + irq_set_chip_and_handler(fpga->irq, NULL, NULL); + + return 0; +} + +static const struct of_device_id cplds_id_table[] = { + { .compatible = "intel,lubbock-cplds-irqs", }, + { .compatible = "intel,mainstone-cplds-irqs", }, + { } +}; +MODULE_DEVICE_TABLE(of, cplds_id_table); + +static struct platform_driver cplds_driver = { + .driver = { + .name = "pxa_cplds_irqs", + .of_match_table = of_match_ptr(cplds_id_table), + }, + .probe = cplds_probe, + .remove = cplds_remove, + .resume = cplds_resume, +}; + +module_platform_driver(cplds_driver); + +MODULE_DESCRIPTION("PXA Cplds interrupts driver"); +MODULE_AUTHOR("Robert Jarzmik "); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From 277688639f98a9e34a6f109f9cd6129f92e718c1 Mon Sep 17 00:00:00 2001 From: Robert Jarzmik Date: Fri, 24 Apr 2015 23:22:35 +0200 Subject: ARM: pxa: mainstone: use new pxa_cplds driver As the interrupt handling was transferred to the pxa_cplds driver, make the switch in mainstone platform code. Fixes: 157d2644cb0c ("ARM: pxa: change gpio to platform device") Signed-off-by: Robert Jarzmik Acked-by: Arnd Bergmann --- arch/arm/mach-pxa/include/mach/mainstone.h | 6 +- arch/arm/mach-pxa/mainstone.c | 115 +++++++---------------------- 2 files changed, 31 insertions(+), 90 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-pxa/include/mach/mainstone.h b/arch/arm/mach-pxa/include/mach/mainstone.h index 1bfc4e822a41..e82a7d31104e 100644 --- a/arch/arm/mach-pxa/include/mach/mainstone.h +++ b/arch/arm/mach-pxa/include/mach/mainstone.h @@ -120,7 +120,9 @@ #define MST_PCMCIA_PWR_VCC_50 0x4 /* voltage VCC = 5.0V */ /* board specific IRQs */ -#define MAINSTONE_IRQ(x) (IRQ_BOARD_START + (x)) +#define MAINSTONE_NR_IRQS IRQ_BOARD_START + +#define MAINSTONE_IRQ(x) (MAINSTONE_NR_IRQS + (x)) #define MAINSTONE_MMC_IRQ MAINSTONE_IRQ(0) #define MAINSTONE_USIM_IRQ MAINSTONE_IRQ(1) #define MAINSTONE_USBC_IRQ MAINSTONE_IRQ(2) @@ -136,6 +138,4 @@ #define MAINSTONE_S1_STSCHG_IRQ MAINSTONE_IRQ(14) #define MAINSTONE_S1_IRQ MAINSTONE_IRQ(15) -#define MAINSTONE_NR_IRQS (IRQ_BOARD_START + 16) - #endif diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c index 78b84c0dfc79..2c0658cf6be2 100644 --- a/arch/arm/mach-pxa/mainstone.c +++ b/arch/arm/mach-pxa/mainstone.c @@ -13,6 +13,7 @@ * published by the Free Software Foundation. */ #include +#include #include #include #include @@ -122,92 +123,6 @@ static unsigned long mainstone_pin_config[] = { GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH, }; -static unsigned long mainstone_irq_enabled; - -static void mainstone_mask_irq(struct irq_data *d) -{ - int mainstone_irq = (d->irq - MAINSTONE_IRQ(0)); - MST_INTMSKENA = (mainstone_irq_enabled &= ~(1 << mainstone_irq)); -} - -static void mainstone_unmask_irq(struct irq_data *d) -{ - int mainstone_irq = (d->irq - MAINSTONE_IRQ(0)); - /* the irq can be acknowledged only if deasserted, so it's done here */ - MST_INTSETCLR &= ~(1 << mainstone_irq); - MST_INTMSKENA = (mainstone_irq_enabled |= (1 << mainstone_irq)); -} - -static struct irq_chip mainstone_irq_chip = { - .name = "FPGA", - .irq_ack = mainstone_mask_irq, - .irq_mask = mainstone_mask_irq, - .irq_unmask = mainstone_unmask_irq, -}; - -static void mainstone_irq_handler(unsigned int irq, struct irq_desc *desc) -{ - unsigned long pending = MST_INTSETCLR & mainstone_irq_enabled; - do { - /* clear useless edge notification */ - desc->irq_data.chip->irq_ack(&desc->irq_data); - if (likely(pending)) { - irq = MAINSTONE_IRQ(0) + __ffs(pending); - generic_handle_irq(irq); - } - pending = MST_INTSETCLR & mainstone_irq_enabled; - } while (pending); -} - -static void __init mainstone_init_irq(void) -{ - int irq; - - pxa27x_init_irq(); - - /* setup extra Mainstone irqs */ - for(irq = MAINSTONE_IRQ(0); irq <= MAINSTONE_IRQ(15); irq++) { - irq_set_chip_and_handler(irq, &mainstone_irq_chip, - handle_level_irq); - if (irq == MAINSTONE_IRQ(10) || irq == MAINSTONE_IRQ(14)) - set_irq_flags(irq, IRQF_VALID | IRQF_PROBE | IRQF_NOAUTOEN); - else - set_irq_flags(irq, IRQF_VALID | IRQF_PROBE); - } - set_irq_flags(MAINSTONE_IRQ(8), 0); - set_irq_flags(MAINSTONE_IRQ(12), 0); - - MST_INTMSKENA = 0; - MST_INTSETCLR = 0; - - irq_set_chained_handler(PXA_GPIO_TO_IRQ(0), mainstone_irq_handler); - irq_set_irq_type(PXA_GPIO_TO_IRQ(0), IRQ_TYPE_EDGE_FALLING); -} - -#ifdef CONFIG_PM - -static void mainstone_irq_resume(void) -{ - MST_INTMSKENA = mainstone_irq_enabled; -} - -static struct syscore_ops mainstone_irq_syscore_ops = { - .resume = mainstone_irq_resume, -}; - -static int __init mainstone_irq_device_init(void) -{ - if (machine_is_mainstone()) - register_syscore_ops(&mainstone_irq_syscore_ops); - - return 0; -} - -device_initcall(mainstone_irq_device_init); - -#endif - - static struct resource smc91x_resources[] = { [0] = { .start = (MST_ETH_PHYS + 0x300), @@ -487,11 +402,37 @@ static struct platform_device mst_gpio_keys_device = { }, }; +static struct resource mst_cplds_resources[] = { + [0] = { + .start = MST_FPGA_PHYS + 0xc0, + .end = MST_FPGA_PHYS + 0xe0 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = PXA_GPIO_TO_IRQ(0), + .end = PXA_GPIO_TO_IRQ(0), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE, + }, + [2] = { + .start = MAINSTONE_IRQ(0), + .end = MAINSTONE_IRQ(15), + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device mst_cplds_device = { + .name = "pxa_cplds_irqs", + .id = -1, + .resource = &mst_cplds_resources[0], + .num_resources = 3, +}; + static struct platform_device *platform_devices[] __initdata = { &smc91x_device, &mst_flash_device[0], &mst_flash_device[1], &mst_gpio_keys_device, + &mst_cplds_device, }; static struct pxaohci_platform_data mainstone_ohci_platform_data = { @@ -718,7 +659,7 @@ MACHINE_START(MAINSTONE, "Intel HCDDBBVA0 Development Platform (aka Mainstone)") .atag_offset = 0x100, /* BLOB boot parameter setting */ .map_io = mainstone_map_io, .nr_irqs = MAINSTONE_NR_IRQS, - .init_irq = mainstone_init_irq, + .init_irq = pxa27x_init_irq, .handle_irq = pxa27x_handle_irq, .init_time = pxa_timer_init, .init_machine = mainstone_init, -- cgit v1.2.3 From fc9e38c0f4d38bfc68b405cf48365d65f7b6319e Mon Sep 17 00:00:00 2001 From: Robert Jarzmik Date: Sun, 14 Dec 2014 23:04:14 +0100 Subject: ARM: pxa: lubbock: use new pxa_cplds driver As the interrupt handling was transferred to the pxa_cplds driver, make the switch in lubbock platform code. Fixes: 157d2644cb0c ("ARM: pxa: change gpio to platform device") Signed-off-by: Robert Jarzmik Acked-by: Arnd Bergmann --- arch/arm/mach-pxa/include/mach/lubbock.h | 7 +- arch/arm/mach-pxa/lubbock.c | 108 +++++++++---------------------- 2 files changed, 33 insertions(+), 82 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-pxa/include/mach/lubbock.h b/arch/arm/mach-pxa/include/mach/lubbock.h index 958cd6af9384..1eecf794acd2 100644 --- a/arch/arm/mach-pxa/include/mach/lubbock.h +++ b/arch/arm/mach-pxa/include/mach/lubbock.h @@ -37,7 +37,9 @@ #define LUB_GP __LUB_REG(LUBBOCK_FPGA_PHYS + 0x100) /* Board specific IRQs */ -#define LUBBOCK_IRQ(x) (IRQ_BOARD_START + (x)) +#define LUBBOCK_NR_IRQS IRQ_BOARD_START + +#define LUBBOCK_IRQ(x) (LUBBOCK_NR_IRQS + (x)) #define LUBBOCK_SD_IRQ LUBBOCK_IRQ(0) #define LUBBOCK_SA1111_IRQ LUBBOCK_IRQ(1) #define LUBBOCK_USB_IRQ LUBBOCK_IRQ(2) /* usb connect */ @@ -47,8 +49,7 @@ #define LUBBOCK_USB_DISC_IRQ LUBBOCK_IRQ(6) /* usb disconnect */ #define LUBBOCK_LAST_IRQ LUBBOCK_IRQ(6) -#define LUBBOCK_SA1111_IRQ_BASE (IRQ_BOARD_START + 16) -#define LUBBOCK_NR_IRQS (IRQ_BOARD_START + 16 + 55) +#define LUBBOCK_SA1111_IRQ_BASE (LUBBOCK_NR_IRQS + 32) #ifndef __ASSEMBLY__ extern void lubbock_set_misc_wr(unsigned int mask, unsigned int set); diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c index d8a1be619f21..4ac9ab80d24b 100644 --- a/arch/arm/mach-pxa/lubbock.c +++ b/arch/arm/mach-pxa/lubbock.c @@ -12,6 +12,7 @@ * published by the Free Software Foundation. */ #include +#include #include #include #include @@ -123,84 +124,6 @@ void lubbock_set_misc_wr(unsigned int mask, unsigned int set) } EXPORT_SYMBOL(lubbock_set_misc_wr); -static unsigned long lubbock_irq_enabled; - -static void lubbock_mask_irq(struct irq_data *d) -{ - int lubbock_irq = (d->irq - LUBBOCK_IRQ(0)); - LUB_IRQ_MASK_EN = (lubbock_irq_enabled &= ~(1 << lubbock_irq)); -} - -static void lubbock_unmask_irq(struct irq_data *d) -{ - int lubbock_irq = (d->irq - LUBBOCK_IRQ(0)); - /* the irq can be acknowledged only if deasserted, so it's done here */ - LUB_IRQ_SET_CLR &= ~(1 << lubbock_irq); - LUB_IRQ_MASK_EN = (lubbock_irq_enabled |= (1 << lubbock_irq)); -} - -static struct irq_chip lubbock_irq_chip = { - .name = "FPGA", - .irq_ack = lubbock_mask_irq, - .irq_mask = lubbock_mask_irq, - .irq_unmask = lubbock_unmask_irq, -}; - -static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc) -{ - unsigned long pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled; - do { - /* clear our parent irq */ - desc->irq_data.chip->irq_ack(&desc->irq_data); - if (likely(pending)) { - irq = LUBBOCK_IRQ(0) + __ffs(pending); - generic_handle_irq(irq); - } - pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled; - } while (pending); -} - -static void __init lubbock_init_irq(void) -{ - int irq; - - pxa25x_init_irq(); - - /* setup extra lubbock irqs */ - for (irq = LUBBOCK_IRQ(0); irq <= LUBBOCK_LAST_IRQ; irq++) { - irq_set_chip_and_handler(irq, &lubbock_irq_chip, - handle_level_irq); - set_irq_flags(irq, IRQF_VALID | IRQF_PROBE); - } - - irq_set_chained_handler(PXA_GPIO_TO_IRQ(0), lubbock_irq_handler); - irq_set_irq_type(PXA_GPIO_TO_IRQ(0), IRQ_TYPE_EDGE_FALLING); -} - -#ifdef CONFIG_PM - -static void lubbock_irq_resume(void) -{ - LUB_IRQ_MASK_EN = lubbock_irq_enabled; -} - -static struct syscore_ops lubbock_irq_syscore_ops = { - .resume = lubbock_irq_resume, -}; - -static int __init lubbock_irq_device_init(void) -{ - if (machine_is_lubbock()) { - register_syscore_ops(&lubbock_irq_syscore_ops); - return 0; - } - return -ENODEV; -} - -device_initcall(lubbock_irq_device_init); - -#endif - static int lubbock_udc_is_connected(void) { return (LUB_MISC_RD & (1 << 9)) == 0; @@ -383,11 +306,38 @@ static struct platform_device lubbock_flash_device[2] = { }, }; +static struct resource lubbock_cplds_resources[] = { + [0] = { + .start = LUBBOCK_FPGA_PHYS + 0xc0, + .end = LUBBOCK_FPGA_PHYS + 0xe0 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = PXA_GPIO_TO_IRQ(0), + .end = PXA_GPIO_TO_IRQ(0), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE, + }, + [2] = { + .start = LUBBOCK_IRQ(0), + .end = LUBBOCK_IRQ(6), + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device lubbock_cplds_device = { + .name = "pxa_cplds_irqs", + .id = -1, + .resource = &lubbock_cplds_resources[0], + .num_resources = 3, +}; + + static struct platform_device *devices[] __initdata = { &sa1111_device, &smc91x_device, &lubbock_flash_device[0], &lubbock_flash_device[1], + &lubbock_cplds_device, }; static struct pxafb_mode_info sharp_lm8v31_mode = { @@ -648,7 +598,7 @@ MACHINE_START(LUBBOCK, "Intel DBPXA250 Development Platform (aka Lubbock)") /* Maintainer: MontaVista Software Inc. */ .map_io = lubbock_map_io, .nr_irqs = LUBBOCK_NR_IRQS, - .init_irq = lubbock_init_irq, + .init_irq = pxa25x_init_irq, .handle_irq = pxa25x_handle_irq, .init_time = pxa_timer_init, .init_machine = lubbock_init, -- cgit v1.2.3 From 12392f5896c9affc03c1ddd95a83c32238862a58 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Wed, 29 Apr 2015 16:55:43 +0300 Subject: ARM: shmobile: koelsch: Fix adv7511 IRQ sensing The adv7511 IRQ is low level triggered, not falling edge triggered. The wrong sense configuration results in no interrupt being triggered at all, breaking hotplug detection. Fix it. Signed-off-by: Laurent Pinchart Fixes: 83a0731b39f3 ("ARM: shmobile: koelsch: Add DU HDMI output support") Signed-off-by: Simon Horman --- arch/arm/boot/dts/r8a7791-koelsch.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index 74c3212f1f11..824ddab9c3ad 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -545,7 +545,7 @@ compatible = "adi,adv7511w"; reg = <0x39>; interrupt-parent = <&gpio3>; - interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + interrupts = <29 IRQ_TYPE_LEVEL_LOW>; adi,input-depth = <8>; adi,input-colorspace = "rgb"; -- cgit v1.2.3 From 102bcb6ed2d1c3ffcc7269afc957c2df11942085 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 4 May 2015 08:54:41 -0700 Subject: ARM: OMAP2+: Fix omap off idle power consumption creeping up If we use a combination of VMODE and I2C4 for retention modes, eventually the off idle power consumption will creep up by about 23mW, even during off mode with I2C4 always staying enabled. Turns out this is because of erratum i531 "Extra Power Consumed When Repeated Start Operation Mode Is Enabled on I2C Interface Dedicated for Smart Reflex (I2C4)" as pointed out by Nishanth Menon . Let's fix the issue by adding i2c_cfg_clear_mask for the bits to clear when initializing the I2C4 adapter so we can clear SREN bit that drives the I2C4 lines low otherwise when there is no traffic. Fixes: 3b8c4ebb7630 ("ARM: OMAP3: Fix idle mode signaling for Cc: stable@vger.kernel.org # v3.16+ sys_clkreq and sys_off_mode") Cc: Kevin Hilman Cc: Tero Kristo Reviewed-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/prm-regbits-34xx.h | 1 + arch/arm/mach-omap2/prm-regbits-44xx.h | 1 + arch/arm/mach-omap2/vc.c | 12 ++++++++++-- arch/arm/mach-omap2/vc.h | 2 ++ arch/arm/mach-omap2/vc3xxx_data.c | 1 + arch/arm/mach-omap2/vc44xx_data.c | 1 + 6 files changed, 16 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-omap2/prm-regbits-34xx.h b/arch/arm/mach-omap2/prm-regbits-34xx.h index cbefbd7cfdb5..661d753df584 100644 --- a/arch/arm/mach-omap2/prm-regbits-34xx.h +++ b/arch/arm/mach-omap2/prm-regbits-34xx.h @@ -112,6 +112,7 @@ #define OMAP3430_VC_CMD_ONLP_SHIFT 16 #define OMAP3430_VC_CMD_RET_SHIFT 8 #define OMAP3430_VC_CMD_OFF_SHIFT 0 +#define OMAP3430_SREN_MASK (1 << 4) #define OMAP3430_HSEN_MASK (1 << 3) #define OMAP3430_MCODE_MASK (0x7 << 0) #define OMAP3430_VALID_MASK (1 << 24) diff --git a/arch/arm/mach-omap2/prm-regbits-44xx.h b/arch/arm/mach-omap2/prm-regbits-44xx.h index b1c7a33e00e7..e794828dee55 100644 --- a/arch/arm/mach-omap2/prm-regbits-44xx.h +++ b/arch/arm/mach-omap2/prm-regbits-44xx.h @@ -35,6 +35,7 @@ #define OMAP4430_GLOBAL_WARM_SW_RST_SHIFT 1 #define OMAP4430_GLOBAL_WUEN_MASK (1 << 16) #define OMAP4430_HSMCODE_MASK (0x7 << 0) +#define OMAP4430_SRMODEEN_MASK (1 << 4) #define OMAP4430_HSMODEEN_MASK (1 << 3) #define OMAP4430_HSSCLL_SHIFT 24 #define OMAP4430_ICEPICK_RST_SHIFT 9 diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c index be9ef834fa81..076fd20d7e5a 100644 --- a/arch/arm/mach-omap2/vc.c +++ b/arch/arm/mach-omap2/vc.c @@ -316,7 +316,8 @@ static void __init omap3_vc_init_pmic_signaling(struct voltagedomain *voltdm) * idle. And we can also scale voltages to zero for off-idle. * Note that no actual voltage scaling during off-idle will * happen unless the board specific twl4030 PMIC scripts are - * loaded. + * loaded. See also omap_vc_i2c_init for comments regarding + * erratum i531. */ val = voltdm->read(OMAP3_PRM_VOLTCTRL_OFFSET); if (!(val & OMAP3430_PRM_VOLTCTRL_SEL_OFF)) { @@ -704,9 +705,16 @@ static void __init omap_vc_i2c_init(struct voltagedomain *voltdm) return; } + /* + * Note that for omap3 OMAP3430_SREN_MASK clears SREN to work around + * erratum i531 "Extra Power Consumed When Repeated Start Operation + * Mode Is Enabled on I2C Interface Dedicated for Smart Reflex (I2C4)". + * Otherwise I2C4 eventually leads into about 23mW extra power being + * consumed even during off idle using VMODE. + */ i2c_high_speed = voltdm->pmic->i2c_high_speed; if (i2c_high_speed) - voltdm->rmw(vc->common->i2c_cfg_hsen_mask, + voltdm->rmw(vc->common->i2c_cfg_clear_mask, vc->common->i2c_cfg_hsen_mask, vc->common->i2c_cfg_reg); diff --git a/arch/arm/mach-omap2/vc.h b/arch/arm/mach-omap2/vc.h index cdbdd78e755e..89b83b7ff3ec 100644 --- a/arch/arm/mach-omap2/vc.h +++ b/arch/arm/mach-omap2/vc.h @@ -34,6 +34,7 @@ struct voltagedomain; * @cmd_ret_shift: RET field shift in PRM_VC_CMD_VAL_* register * @cmd_off_shift: OFF field shift in PRM_VC_CMD_VAL_* register * @i2c_cfg_reg: I2C configuration register offset + * @i2c_cfg_clear_mask: high-speed mode bit clear mask in I2C config register * @i2c_cfg_hsen_mask: high-speed mode bit field mask in I2C config register * @i2c_mcode_mask: MCODE field mask for I2C config register * @@ -52,6 +53,7 @@ struct omap_vc_common { u8 cmd_ret_shift; u8 cmd_off_shift; u8 i2c_cfg_reg; + u8 i2c_cfg_clear_mask; u8 i2c_cfg_hsen_mask; u8 i2c_mcode_mask; }; diff --git a/arch/arm/mach-omap2/vc3xxx_data.c b/arch/arm/mach-omap2/vc3xxx_data.c index 75bc4aa22b3a..71d74c9172c1 100644 --- a/arch/arm/mach-omap2/vc3xxx_data.c +++ b/arch/arm/mach-omap2/vc3xxx_data.c @@ -40,6 +40,7 @@ static struct omap_vc_common omap3_vc_common = { .cmd_onlp_shift = OMAP3430_VC_CMD_ONLP_SHIFT, .cmd_ret_shift = OMAP3430_VC_CMD_RET_SHIFT, .cmd_off_shift = OMAP3430_VC_CMD_OFF_SHIFT, + .i2c_cfg_clear_mask = OMAP3430_SREN_MASK | OMAP3430_HSEN_MASK, .i2c_cfg_hsen_mask = OMAP3430_HSEN_MASK, .i2c_cfg_reg = OMAP3_PRM_VC_I2C_CFG_OFFSET, .i2c_mcode_mask = OMAP3430_MCODE_MASK, diff --git a/arch/arm/mach-omap2/vc44xx_data.c b/arch/arm/mach-omap2/vc44xx_data.c index 085e5d6a04fd..2abd5fa8a697 100644 --- a/arch/arm/mach-omap2/vc44xx_data.c +++ b/arch/arm/mach-omap2/vc44xx_data.c @@ -42,6 +42,7 @@ static const struct omap_vc_common omap4_vc_common = { .cmd_ret_shift = OMAP4430_RET_SHIFT, .cmd_off_shift = OMAP4430_OFF_SHIFT, .i2c_cfg_reg = OMAP4_PRM_VC_CFG_I2C_MODE_OFFSET, + .i2c_cfg_clear_mask = OMAP4430_SRMODEEN_MASK | OMAP4430_HSMODEEN_MASK, .i2c_cfg_hsen_mask = OMAP4430_HSMODEEN_MASK, .i2c_mcode_mask = OMAP4430_HSMCODE_MASK, }; -- cgit v1.2.3 From 1819e3034ee26ffadc71880064ed8b8e7d74f52c Mon Sep 17 00:00:00 2001 From: Pavel Machek Date: Sun, 1 Mar 2015 21:07:08 +0200 Subject: ARM: dts: OMAP3-N900: Add microphone bias voltages N900 audio recording needs that codec provides bias voltage for integrated digital microphone and headset microphone depending which one is used. Digital microphone uses 2 V bias and it comes from the codec A part. Codec B part drives the headset microphone bias and that is set to 2.5 V. Cc: stable@vger.kernel.org # v3.16+ Signed-off-by: Pavel Machek [Jarkko: Headset mic bias changed to 2 (2.5 V) as it was before commit e2e8bfdf6157 ("ASoC: tlv320aic3x: Convert mic bias to a supply widget")] Signed-off-by: Jarkko Nikula Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-n900.dts | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index a29315833ecd..5c16145920ea 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -498,6 +498,8 @@ DRVDD-supply = <&vmmc2>; IOVDD-supply = <&vio>; DVDD-supply = <&vio>; + + ai3x-micbias-vg = <1>; }; tlv320aic3x_aux: tlv320aic3x@19 { @@ -509,6 +511,8 @@ DRVDD-supply = <&vmmc2>; IOVDD-supply = <&vio>; DVDD-supply = <&vio>; + + ai3x-micbias-vg = <2>; }; tsl2563: tsl2563@29 { -- cgit v1.2.3 From 67defd5c0ee5270948104784c8fc8f6d4a99682b Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 24 Mar 2015 12:19:19 +0200 Subject: ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO We need to enable EXTCON_USB_GPIO_USB and not EXTCON_GPIO_USB. Fixes: c08a54c0ebeb ("ARM: omap2plus_defconfig: Enable EXTCON_GPIO_USB") Reported-by: Nishant Menon Signed-off-by: Roger Quadros Acked-by-by: Nishanth Menon Acked-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/configs/omap2plus_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 9ff7b54b2a83..3743ca221d40 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -393,7 +393,7 @@ CONFIG_TI_EDMA=y CONFIG_DMA_OMAP=y # CONFIG_IOMMU_SUPPORT is not set CONFIG_EXTCON=m -CONFIG_EXTCON_GPIO=m +CONFIG_EXTCON_USB_GPIO=m CONFIG_EXTCON_PALMAS=m CONFIG_TI_EMIF=m CONFIG_PWM=y -- cgit v1.2.3 From 2055088b5e17b450fcfb536568aee00eccd0ced5 Mon Sep 17 00:00:00 2001 From: Sebastian Reichel Date: Tue, 31 Mar 2015 03:28:10 +0200 Subject: ARM: dts: omap3: Add #iommu-cells to isp and iva iommu Add missing #iommu-cells property to the isp and iva iommu nodes. This fixes the binding (property is required according to the generic iommu binding) and removes the following kernel warning triggered once the iommu nodes are referenced: [ 0.647521] /ocp/isp@480bc000: could not get #iommu-cells for /ocp/mmu@480bd400 Signed-off-by: Sebastian Reichel Cc: Laurent Pinchart Acked-by: Sakari Ailus Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3.dtsi | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index d18a90f5eca3..69a40cfc1f29 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -456,6 +456,7 @@ }; mmu_isp: mmu@480bd400 { + #iommu-cells = <0>; compatible = "ti,omap2-iommu"; reg = <0x480bd400 0x80>; interrupts = <24>; @@ -464,6 +465,7 @@ }; mmu_iva: mmu@5d000000 { + #iommu-cells = <0>; compatible = "ti,omap2-iommu"; reg = <0x5d000000 0x80>; interrupts = <28>; -- cgit v1.2.3 From e7a7357341664148cabf98a3ab50b5d449afca0b Mon Sep 17 00:00:00 2001 From: Grygorii Strashko Date: Wed, 8 Apr 2015 18:56:26 -0500 Subject: ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x The interrupt polarity provided in devicetree is used to configure the interrupt controller(ARM GIC), however, it seems that we have an inverter at the GIC boundary inside AM57xx which inverts the signal input from sys_irq external interrupt source. Further, as per GIC distributor TRM, http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438d/BGBHIACJ.html#BABJFCFB ARM GIC distributor does not support IRQ trigger type IRQ_TYPE_LEVEL_LOW, and only rising or level high signals. However, for some reason, the current configuration(which gets ignored by GIC driver) functions on some platforms, however, on few platforms results in infinite interrupts hogging the system down. Switch over to rising edge for GIC configuration which is also aligned with trigger point from the RTC chip and the internal inversion. Fixes: 5a0f93c6576a ("ARM: dts: Add am57xx-beagle-x15") Signed-off-by: Grygorii Strashko Signed-off-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-beagle-x15.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index 15f198e4864d..7ac6ee2c52d8 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -455,7 +455,7 @@ mcp_rtc: rtc@6f { compatible = "microchip,mcp7941x"; reg = <0x6f>; - interrupts = ; /* IRQ_SYS_1N */ + interrupts = ; /* IRQ_SYS_1N */ pinctrl-names = "default"; pinctrl-0 = <&mcp79410_pins_default>; -- cgit v1.2.3 From 00edd3170c757772f74c533e61298be249447a11 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Wed, 8 Apr 2015 18:56:27 -0500 Subject: ARM: dts: am57xx-beagle-x15: Fix RTC aliases With commit bc078316d86c ("ARM: dts: DRA7: Add node for RTC"), we now have AM57xx RTC register itself as alias 0 even before DS1307 or TPS rtc drivers are loaded up. However, since neither TPS, nor AM57xx RTC are capable of being backedup by battery, we would like to maintain the "primary" rtc as mcp79410 rtc device. This also generates the following warnings in the bootlog highlighting the issue: [ 5.895445] rtc-ds1307 2-006f: /aliases ID 0 not available ... [ 6.476285] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: /aliases ID 1 not available So, add proper aliases to ensure that RTC order is always consistent to userspace immaterial of probe order. Signed-off-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-beagle-x15.dts | 1 + arch/arm/boot/dts/dra7.dtsi | 2 +- 2 files changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index 7ac6ee2c52d8..be9b6a552ae2 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -18,6 +18,7 @@ aliases { rtc0 = &mcp_rtc; rtc1 = &tps659038_rtc; + rtc2 = &rtc; }; memory { diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 5332b57b4950..0f73fea9f5c3 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -1203,7 +1203,7 @@ status = "disabled"; }; - rtc@48838000 { + rtc: rtc@48838000 { compatible = "ti,am3352-rtc"; reg = <0x48838000 0x100>; interrupts = , -- cgit v1.2.3 From faa4ec1eedbe6d352dc22c945540a64b5c896a95 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 9 Apr 2015 10:59:26 -0500 Subject: ARM: dts: am437x-sk: fix for new newhaven display module revision AM437x Starter Kit uses a NewHaven Display module with a 4.3" display and EDT FT5306 touchscreen On that module's new revision, NewHave decided to change the pinout on the 6 pin flat-pcb touchscreen connector so that instead of having WAKE pin, we now have RESETn. The new display module is available on AM437x SK Beta and all new revisions while the older revision is only available on AM437x SK Alpha which, unfortunately, can't be supported anymore in mainline without a revert of this patch. Signed-off-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-sk-evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts index 8ae29c955c11..fbc50f92e622 100644 --- a/arch/arm/boot/dts/am437x-sk-evm.dts +++ b/arch/arm/boot/dts/am437x-sk-evm.dts @@ -473,7 +473,7 @@ interrupt-parent = <&gpio0>; interrupts = <31 0>; - wake-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; touchscreen-size-x = <480>; touchscreen-size-y = <272>; -- cgit v1.2.3 From f6b957fdce50ddbd1899948ab109cca64e571eba Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 9 Apr 2015 10:59:27 -0500 Subject: ARM: dts: am437x-sk: reduce col-scan-delay-us The new AM437x SK Beta boards have removed the large capacitors on the gpio-matrix column lines which means we can reduce col-scan-delay-us to 5us without loosing functionality. Signed-off-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-sk-evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts index fbc50f92e622..c17097d2c167 100644 --- a/arch/arm/boot/dts/am437x-sk-evm.dts +++ b/arch/arm/boot/dts/am437x-sk-evm.dts @@ -49,7 +49,7 @@ pinctrl-0 = <&matrix_keypad_pins>; debounce-delay-ms = <5>; - col-scan-delay-us = <1500>; + col-scan-delay-us = <5>; row-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH /* Bank5, pin5 */ &gpio5 6 GPIO_ACTIVE_HIGH>; /* Bank5, pin6 */ -- cgit v1.2.3 From 5eb6719816faad8e915d4f46ad61a440d641d183 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Wed, 8 Apr 2015 17:40:59 -0500 Subject: ARM: dts: am57xx-beagle-x15: Switch UART mux pins BeagleBoard-X15 pre-production change includes switching over to UART pins that now allow for UART download capability. All original boards should either have been returned for modifications or already modified for the required change and maintaining compatibility for older boards are no longer needed. Signed-off-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-beagle-x15.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index be9b6a552ae2..dd53ea56b0ed 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -131,8 +131,8 @@ uart3_pins_default: uart3_pins_default { pinctrl-single,pins = < - 0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd.rxd */ - 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd.txd */ + 0x3f8 (PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */ + 0x3fc (PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */ >; }; @@ -479,7 +479,7 @@ &uart3 { status = "okay"; interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, - <&dra7_pmx_core 0x248>; + <&dra7_pmx_core 0x3f8>; pinctrl-names = "default"; pinctrl-0 = <&uart3_pins_default>; -- cgit v1.2.3 From ed12f102ba9f55d2617fc6b5e4fbecbf9a132ba7 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Thu, 9 Apr 2015 17:33:17 -0500 Subject: ARM: dts: am57xx-beagle-x15: Switch GPIO fan number BeagleBoard-X15 pre-production change includes switching the GPIO fan gpio over from 1 to 2 to allow for a potential fix at a later point in time for USB client VBUS detection using PMIC VBUS detect capability. Signed-off-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-beagle-x15.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index dd53ea56b0ed..7128fad991ac 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -84,7 +84,7 @@ gpio_fan: gpio_fan { /* Based on 5v 500mA AFB02505HHB */ compatible = "gpio-fan"; - gpios = <&tps659038_gpio 1 GPIO_ACTIVE_HIGH>; + gpios = <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>; gpio-fan,speed-map = <0 0>, <13000 1>; #cooling-cells = <2>; -- cgit v1.2.3 From 1822734677d95888d18e3c0e0743727effa62f8e Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Thu, 16 Apr 2015 16:56:33 -0500 Subject: ARM: dts: dra7: Fix efuse register size for ABB Fix a typo in DRA7 dtsi where 12 bytes are needed for register description of ABB efuse registers, however only 8 bytes are provided to map. For some weird reason, this does not generate abort at offset 0x8, probably due to default maps already provided in io.c for the bus register ranges. Reported-by: Matt Gessner Reported-by: Suman Anna Signed-off-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 0f73fea9f5c3..f03a091cd076 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -911,7 +911,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>, - <0x4ae06014 0x4>, <0x4a003b20 0x8>, + <0x4ae06014 0x4>, <0x4a003b20 0xc>, <0x4ae0c158 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -944,7 +944,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>, - <0x4ae06010 0x4>, <0x4a0025cc 0x8>, + <0x4ae06010 0x4>, <0x4a0025cc 0xc>, <0x4a002470 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -977,7 +977,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>, - <0x4ae06010 0x4>, <0x4a0025e0 0x8>, + <0x4ae06010 0x4>, <0x4a0025e0 0xc>, <0x4a00246c 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -1010,7 +1010,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>, - <0x4ae06010 0x4>, <0x4a003b08 0x8>, + <0x4ae06010 0x4>, <0x4a003b08 0xc>, <0x4ae0c154 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", -- cgit v1.2.3 From e7309c2673a389a495fcfad70376d3bae8b9bc89 Mon Sep 17 00:00:00 2001 From: Suman Anna Date: Fri, 24 Apr 2015 12:54:20 -0500 Subject: bus: omap_l3_noc: Fix master id address decoding for OMAP5 The L3 Error handling on OMAP5 for the most part is very similar to that of OMAP4, and had leveraged common data structures and register layout definitions so far. Upon closer inspection, there are a few minor differences causing an incorrect decoding and reporting of the master NIU upon an error: 1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies 11 bits on OMAP5 as against 8 bits on OMAP4, with the master NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR field. 2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3 input sources on OMAP5. The common DEBUGSS source is at a different input on each SoC. Fix the above issues by using a OMAP5-specific compatible property and using SoC-specific data where there are differences. Signed-off-by: Suman Anna Acked-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index efe5f737f39b..7d24ae0306b5 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -128,7 +128,7 @@ * hierarchy. */ ocp { - compatible = "ti,omap4-l3-noc", "simple-bus"; + compatible = "ti,omap5-l3-noc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges; -- cgit v1.2.3 From dc0e3db4ec7c1e73e3283ad39b68eff32b7dc8a1 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Tue, 5 May 2015 14:35:49 -0300 Subject: ARM: multi_v7_defconfig: Select more FSL SoCs Select IMX50, IMX6SX and LS1021A SoC support. Signed-off-by: Fabio Estevam Signed-off-by: Arnd Bergmann --- arch/arm/configs/multi_v7_defconfig | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index ab86655c1f4b..0ca4a3eaf65d 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -39,11 +39,14 @@ CONFIG_ARCH_HIP04=y CONFIG_ARCH_KEYSTONE=y CONFIG_ARCH_MESON=y CONFIG_ARCH_MXC=y +CONFIG_SOC_IMX50=y CONFIG_SOC_IMX51=y CONFIG_SOC_IMX53=y CONFIG_SOC_IMX6Q=y CONFIG_SOC_IMX6SL=y +CONFIG_SOC_IMX6SX=y CONFIG_SOC_VF610=y +CONFIG_SOC_LS1021A=y CONFIG_ARCH_OMAP3=y CONFIG_ARCH_OMAP4=y CONFIG_SOC_OMAP5=y -- cgit v1.2.3