From 871c3cf4ea7d5baf58e0a40bce7431ca5525aa2a Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Sat, 4 Oct 2014 16:02:27 +0200 Subject: mfd: stmpe: Fix STMPE24xx GPMR LSB The least significat byte of the GPIO value read register on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct against datasheet and tested on the STMPE2401 hardware. Signed-off-by: Linus Walleij Signed-off-by: Lee Jones --- drivers/mfd/stmpe.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mfd/stmpe.h b/drivers/mfd/stmpe.h index 2d045f26f193..bee0abf82040 100644 --- a/drivers/mfd/stmpe.h +++ b/drivers/mfd/stmpe.h @@ -269,7 +269,7 @@ int stmpe_remove(struct stmpe *stmpe); #define STMPE24XX_REG_CHIP_ID 0x80 #define STMPE24XX_REG_IEGPIOR_LSB 0x18 #define STMPE24XX_REG_ISGPIOR_MSB 0x19 -#define STMPE24XX_REG_GPMR_LSB 0xA5 +#define STMPE24XX_REG_GPMR_LSB 0xA4 #define STMPE24XX_REG_GPSR_LSB 0x85 #define STMPE24XX_REG_GPCR_LSB 0x88 #define STMPE24XX_REG_GPDR_LSB 0x8B -- cgit v1.2.3 From 451be648064064c3edbc532b4a3469d2d018ff5c Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Thu, 2 Oct 2014 09:25:17 +0200 Subject: mfd: rtsx: Fix build warnings for !PM rtsx_pci_power_off() is called only from rtsx_pci_suspend(), which isn't built when PM is disabled. Signed-off-by: Thierry Reding Signed-off-by: Lee Jones --- drivers/mfd/rtsx_pcr.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers') diff --git a/drivers/mfd/rtsx_pcr.c b/drivers/mfd/rtsx_pcr.c index f2643c221d34..30f7ca89a0e6 100644 --- a/drivers/mfd/rtsx_pcr.c +++ b/drivers/mfd/rtsx_pcr.c @@ -947,6 +947,7 @@ static void rtsx_pci_idle_work(struct work_struct *work) mutex_unlock(&pcr->pcr_mutex); } +#ifdef CONFIG_PM static void rtsx_pci_power_off(struct rtsx_pcr *pcr, u8 pm_state) { if (pcr->ops->turn_off_led) @@ -961,6 +962,7 @@ static void rtsx_pci_power_off(struct rtsx_pcr *pcr, u8 pm_state) if (pcr->ops->force_power_down) pcr->ops->force_power_down(pcr, pm_state); } +#endif static int rtsx_pci_init_hw(struct rtsx_pcr *pcr) { -- cgit v1.2.3 From b6684228726cc25551a43f5c0bd9c5f977f10f48 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Fri, 26 Sep 2014 12:55:28 +0200 Subject: mfd: viperboard: Fix platform-device id collision Allow more than one viperboard to be connected by registering with PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE. The subdevices are currently registered with PLATFORM_DEVID_NONE, which will cause a name collision on the platform bus when a second viperboard is plugged in: viperboard 1-2.4:1.0: version 0.00 found at bus 001 address 004 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 181 at /home/johan/work/omicron/src/linux/fs/sysfs/dir.c:31 sysfs_warn_dup+0x74/0x84() sysfs: cannot create duplicate filename '/bus/platform/devices/viperboard-gpio' Modules linked in: i2c_viperboard viperboard netconsole [last unloaded: viperboard] CPU: 0 PID: 181 Comm: bash Tainted: G W 3.17.0-rc6 #1 [] (unwind_backtrace) from [] (show_stack+0x20/0x24) [] (show_stack) from [] (dump_stack+0x24/0x28) [] (dump_stack) from [] (warn_slowpath_common+0x80/0x98) [] (warn_slowpath_common) from [] (warn_slowpath_fmt+0x40/0x48) [] (warn_slowpath_fmt) from [] (sysfs_warn_dup+0x74/0x84) [] (sysfs_warn_dup) from [] (sysfs_do_create_link_sd.isra.2+0xcc/0xd0) [] (sysfs_do_create_link_sd.isra.2) from [] (sysfs_create_link+0x3c/0x48) [] (sysfs_create_link) from [] (bus_add_device+0x12c/0x1e0) [] (bus_add_device) from [] (device_add+0x410/0x584) [] (device_add) from [] (platform_device_add+0xd8/0x26c) [] (platform_device_add) from [] (mfd_add_device+0x240/0x344) [] (mfd_add_device) from [] (mfd_add_devices+0xb8/0x110) [] (mfd_add_devices) from [] (vprbrd_probe+0x160/0x1b0 [viperboard]) [] (vprbrd_probe [viperboard]) from [] (usb_probe_interface+0x1bc/0x2a8) [] (usb_probe_interface) from [] (driver_probe_device+0x14c/0x3ac) [] (driver_probe_device) from [] (__driver_attach+0xa4/0xa8) [] (__driver_attach) from [] (bus_for_each_dev+0x70/0xa4) [] (bus_for_each_dev) from [] (driver_attach+0x2c/0x30) [] (driver_attach) from [] (usb_store_new_id+0x170/0x1ac) [] (usb_store_new_id) from [] (new_id_store+0x34/0x3c) [] (new_id_store) from [] (drv_attr_store+0x30/0x3c) [] (drv_attr_store) from [] (sysfs_kf_write+0x5c/0x60) [] (sysfs_kf_write) from [] (kernfs_fop_write+0xd4/0x194) [] (kernfs_fop_write) from [] (vfs_write+0xb4/0x1c0) [] (vfs_write) from [] (SyS_write+0x4c/0xa0) [] (SyS_write) from [] (ret_fast_syscall+0x0/0x48) ---[ end trace 98e8603c22d65817 ]--- viperboard 1-2.4:1.0: Failed to add mfd devices to core. viperboard: probe of 1-2.4:1.0 failed with error -17 Signed-off-by: Johan Hovold Signed-off-by: Lee Jones --- drivers/mfd/viperboard.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/mfd/viperboard.c b/drivers/mfd/viperboard.c index e00f5340ed87..3c2b8f9e3c84 100644 --- a/drivers/mfd/viperboard.c +++ b/drivers/mfd/viperboard.c @@ -93,8 +93,9 @@ static int vprbrd_probe(struct usb_interface *interface, version >> 8, version & 0xff, vb->usb_dev->bus->busnum, vb->usb_dev->devnum); - ret = mfd_add_devices(&interface->dev, -1, vprbrd_devs, - ARRAY_SIZE(vprbrd_devs), NULL, 0, NULL); + ret = mfd_add_devices(&interface->dev, PLATFORM_DEVID_AUTO, + vprbrd_devs, ARRAY_SIZE(vprbrd_devs), NULL, 0, + NULL); if (ret != 0) { dev_err(&interface->dev, "Failed to add mfd devices to core."); goto error; -- cgit v1.2.3 From 43fc9396cac3f7498e07a22e6a987b911462fa58 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Fri, 10 Oct 2014 10:22:01 +0200 Subject: mfd: max77693: Use proper regmap for handling MUIC interrupts Interrupts coming from Maxim77693 MUIC block (MicroUSB Interface Controller) were not handled at all because wrong regmap was used for MUIC's regmap_irq_chip. The MUIC component of Maxim 77693 uses different I2C address thus second regmap is created and used by max77693 extcon driver. The registers for MUIC interrupts are also in that block and should be handled by that second regmap. However the regmap irq chip for MUIC was configured with default regmap which could not read MUIC registers. Fixes: 342d669c1ee4 ("mfd: max77693: Handle IRQs using regmap") Cc: Signed-off-by: Krzysztof Kozlowski Reviewed-by: Chanwoo Choi Signed-off-by: Lee Jones --- drivers/mfd/max77693.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/mfd/max77693.c b/drivers/mfd/max77693.c index cf008f45968c..22d23fcbb65c 100644 --- a/drivers/mfd/max77693.c +++ b/drivers/mfd/max77693.c @@ -240,7 +240,7 @@ static int max77693_i2c_probe(struct i2c_client *i2c, goto err_irq_charger; } - ret = regmap_add_irq_chip(max77693->regmap, max77693->irq, + ret = regmap_add_irq_chip(max77693->regmap_muic, max77693->irq, IRQF_ONESHOT | IRQF_SHARED | IRQF_TRIGGER_FALLING, 0, &max77693_muic_irq_chip, -- cgit v1.2.3 From c0acb8144bd6d8d88aee1dab33364b7353e9a903 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Fri, 10 Oct 2014 12:48:35 +0200 Subject: mfd: max77693: Fix always masked MUIC interrupts All interrupts coming from MUIC were ignored because interrupt source register was masked. The Maxim 77693 has a "interrupt source" - a separate register and interrupts which give information about PMIC block triggering the individual interrupt (charger, topsys, MUIC, flash LED). By default bootloader could initialize this register to "mask all" value. In such case (observed on Trats2 board) MUIC interrupts won't be generated regardless of their mask status. Regmap irq chip was unmasking individual MUIC interrupts but the source was masked Before introducing regmap irq chip this interrupt source was unmasked, read and acked. Reading and acking is not necessary but unmasking is. Fixes: 342d669c1ee4 ("mfd: max77693: Handle IRQs using regmap") Cc: Signed-off-by: Krzysztof Kozlowski Reviewed-by: Chanwoo Choi Signed-off-by: Lee Jones --- drivers/mfd/max77693.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'drivers') diff --git a/drivers/mfd/max77693.c b/drivers/mfd/max77693.c index 22d23fcbb65c..711773e8e64b 100644 --- a/drivers/mfd/max77693.c +++ b/drivers/mfd/max77693.c @@ -250,6 +250,17 @@ static int max77693_i2c_probe(struct i2c_client *i2c, goto err_irq_muic; } + /* Unmask interrupts from all blocks in interrupt source register */ + ret = regmap_update_bits(max77693->regmap, + MAX77693_PMIC_REG_INTSRC_MASK, + SRC_IRQ_ALL, (unsigned int)~SRC_IRQ_ALL); + if (ret < 0) { + dev_err(max77693->dev, + "Could not unmask interrupts in INTSRC: %d\n", + ret); + goto err_intsrc; + } + pm_runtime_set_active(max77693->dev); ret = mfd_add_devices(max77693->dev, -1, max77693_devs, @@ -261,6 +272,7 @@ static int max77693_i2c_probe(struct i2c_client *i2c, err_mfd: mfd_remove_devices(max77693->dev); +err_intsrc: regmap_del_irq_chip(max77693->irq, max77693->irq_data_muic); err_irq_muic: regmap_del_irq_chip(max77693->irq, max77693->irq_data_charger); -- cgit v1.2.3 From 481c7f868c6d855f31a29c69b445ac4aee9625a6 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Sun, 2 Nov 2014 10:07:56 -0800 Subject: mfd: twl4030-power: Fix poweroff with PM configuration enabled Commit e7cd1d1eb16f ("mfd: twl4030-power: Add generic reset configuration") enabled configuring the PM features for twl4030. This caused poweroff command to fail on devices that have the BCI charger on twl4030 wired, or have power wired for VBUS. Instead of powering off, the device reboots. This is because voltage is detected on charger or VBUS with the default bits enabled for the power transition registers. To fix the issue, let's just clear VBUS and CHG bits as we want poweroff command to keep the system powered off. Fixes: e7cd1d1eb16f ("mfd: twl4030-power: Add generic reset configuration") Cc: stable@vger.kernel.org # v3.16+ Reported-by: Russell King Signed-off-by: Tony Lindgren Signed-off-by: Lee Jones --- drivers/mfd/twl4030-power.c | 52 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+) (limited to 'drivers') diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c index cf92a6d1c532..50f9091bcd38 100644 --- a/drivers/mfd/twl4030-power.c +++ b/drivers/mfd/twl4030-power.c @@ -44,6 +44,15 @@ static u8 twl4030_start_script_address = 0x2b; #define PWR_DEVSLP BIT(1) #define PWR_DEVOFF BIT(0) +/* Register bits for CFG_P1_TRANSITION (also for P2 and P3) */ +#define STARTON_SWBUG BIT(7) /* Start on watchdog */ +#define STARTON_VBUS BIT(5) /* Start on VBUS */ +#define STARTON_VBAT BIT(4) /* Start on battery insert */ +#define STARTON_RTC BIT(3) /* Start on RTC */ +#define STARTON_USB BIT(2) /* Start on USB host */ +#define STARTON_CHG BIT(1) /* Start on charger */ +#define STARTON_PWON BIT(0) /* Start on PWRON button */ + #define SEQ_OFFSYNC (1 << 0) #define PHY_TO_OFF_PM_MASTER(p) (p - 0x36) @@ -606,6 +615,44 @@ twl4030_power_configure_resources(const struct twl4030_power_data *pdata) return 0; } +static int twl4030_starton_mask_and_set(u8 bitmask, u8 bitvalues) +{ + u8 regs[3] = { TWL4030_PM_MASTER_CFG_P1_TRANSITION, + TWL4030_PM_MASTER_CFG_P2_TRANSITION, + TWL4030_PM_MASTER_CFG_P3_TRANSITION, }; + u8 val; + int i, err; + + err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG1, + TWL4030_PM_MASTER_PROTECT_KEY); + if (err) + goto relock; + err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, + TWL4030_PM_MASTER_KEY_CFG2, + TWL4030_PM_MASTER_PROTECT_KEY); + if (err) + goto relock; + + for (i = 0; i < sizeof(regs); i++) { + err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, + &val, regs[i]); + if (err) + break; + val = (~bitmask & val) | (bitmask & bitvalues); + err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, + val, regs[i]); + if (err) + break; + } + + if (err) + pr_err("TWL4030 Register access failed: %i\n", err); + +relock: + return twl_i2c_write_u8(TWL_MODULE_PM_MASTER, 0, + TWL4030_PM_MASTER_PROTECT_KEY); +} + /* * In master mode, start the power off sequence. * After a successful execution, TWL shuts down the power to the SoC @@ -615,6 +662,11 @@ void twl4030_power_off(void) { int err; + /* Disable start on charger or VBUS as it can break poweroff */ + err = twl4030_starton_mask_and_set(STARTON_VBUS | STARTON_CHG, 0); + if (err) + pr_err("TWL4030 Unable to configure start-up\n"); + err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, PWR_DEVOFF, TWL4030_PM_MASTER_P1_SW_EVENTS); if (err) -- cgit v1.2.3