From bce40a36de574376f41f1ff3c4d212a7da2a3c90 Mon Sep 17 00:00:00 2001 From: Philip Langdale Date: Sat, 21 Oct 2006 12:35:02 +0200 Subject: [PATCH] mmc: Add support for mmc v4 high speed mode This adds support for the high-speed modes defined by mmc v4 (assuming the host controller is up to it). On a TI sdhci controller, it improves read speed from 1.3MBps to 2.3MBps. The TI controller can only go up to 24MHz, but everything helps. Another person has taken this basic patch and used it on a Nokia 770 to get a bigger boost because that controller can run at 48MHZ. Signed-off-by: Philip Langdale Signed-off-by: Pierre Ossman --- include/linux/mmc/protocol.h | 47 +++++++++++++++++++++++++++++++++++++++++--- 1 file changed, 44 insertions(+), 3 deletions(-) (limited to 'include/linux/mmc/protocol.h') diff --git a/include/linux/mmc/protocol.h b/include/linux/mmc/protocol.h index 08dec8d9e703..311b6547f561 100644 --- a/include/linux/mmc/protocol.h +++ b/include/linux/mmc/protocol.h @@ -25,14 +25,16 @@ #ifndef MMC_MMC_PROTOCOL_H #define MMC_MMC_PROTOCOL_H -/* Standard MMC commands (3.1) type argument response */ +/* Standard MMC commands (4.1) type argument response */ /* class 1 */ #define MMC_GO_IDLE_STATE 0 /* bc */ #define MMC_SEND_OP_COND 1 /* bcr [31:0] OCR R3 */ #define MMC_ALL_SEND_CID 2 /* bcr R2 */ #define MMC_SET_RELATIVE_ADDR 3 /* ac [31:16] RCA R1 */ #define MMC_SET_DSR 4 /* bc [31:16] RCA */ +#define MMC_SWITCH 6 /* ac [31:0] See below R1b */ #define MMC_SELECT_CARD 7 /* ac [31:16] RCA R1 */ +#define MMC_SEND_EXT_CSD 8 /* adtc R1 */ #define MMC_SEND_CSD 9 /* ac [31:16] RCA R2 */ #define MMC_SEND_CID 10 /* ac [31:16] RCA R2 */ #define MMC_READ_DAT_UNTIL_STOP 11 /* adtc [31:0] dadr R1 */ @@ -87,6 +89,17 @@ #define SD_APP_OP_COND 41 /* bcr [31:0] OCR R3 */ #define SD_APP_SEND_SCR 51 /* adtc R1 */ +/* + * MMC_SWITCH argument format: + * + * [31:26] Always 0 + * [25:24] Access Mode + * [23:16] Location of target Byte in EXT_CSD + * [15:08] Value Byte + * [07:03] Always 0 + * [02:00] Command Set + */ + /* MMC status in R1 Type @@ -230,13 +243,41 @@ struct _mmc_csd { #define CSD_STRUCT_VER_1_0 0 /* Valid for system specification 1.0 - 1.2 */ #define CSD_STRUCT_VER_1_1 1 /* Valid for system specification 1.4 - 2.2 */ -#define CSD_STRUCT_VER_1_2 2 /* Valid for system specification 3.1 */ +#define CSD_STRUCT_VER_1_2 2 /* Valid for system specification 3.1 - 3.2 - 3.31 - 4.0 - 4.1 */ +#define CSD_STRUCT_EXT_CSD 3 /* Version is coded in CSD_STRUCTURE in EXT_CSD */ #define CSD_SPEC_VER_0 0 /* Implements system specification 1.0 - 1.2 */ #define CSD_SPEC_VER_1 1 /* Implements system specification 1.4 */ #define CSD_SPEC_VER_2 2 /* Implements system specification 2.0 - 2.2 */ -#define CSD_SPEC_VER_3 3 /* Implements system specification 3.1 */ +#define CSD_SPEC_VER_3 3 /* Implements system specification 3.1 - 3.2 - 3.31 */ +#define CSD_SPEC_VER_4 4 /* Implements system specification 4.0 - 4.1 */ + +/* + * EXT_CSD fields + */ + +#define EXT_CSD_HS_TIMING 185 /* R/W */ +#define EXT_CSD_CARD_TYPE 196 /* RO */ + +/* + * EXT_CSD field definitions + */ + +#define EXT_CSD_CMD_SET_NORMAL (1<<0) +#define EXT_CSD_CMD_SET_SECURE (1<<1) +#define EXT_CSD_CMD_SET_CPSECURE (1<<2) + +#define EXT_CSD_CARD_TYPE_26 (1<<0) /* Card can run at 26MHz */ +#define EXT_CSD_CARD_TYPE_52 (1<<1) /* Card can run at 52MHz */ + +/* + * MMC_SWITCH access modes + */ +#define MMC_SWITCH_MODE_CMD_SET 0x00 /* Change the command set */ +#define MMC_SWITCH_MODE_SET_BITS 0x01 /* Set bits which are 1 in value */ +#define MMC_SWITCH_MODE_CLEAR_BITS 0x02 /* Clear bits which are 1 in value */ +#define MMC_SWITCH_MODE_WRITE_BYTE 0x03 /* Set target to value */ /* * SD bus widths -- cgit v1.2.3 From e45a1bd20fa5b920901879e85cdf5eda21f78d7c Mon Sep 17 00:00:00 2001 From: Philip Langdale Date: Sun, 29 Oct 2006 10:14:19 +0100 Subject: mmc: Add support for mmc v4 wide-bus modes This change adds support for the mmc4 4-bit wide-bus mode. The mmc4 spec defines 8-bit and 4-bit transfer modes. As we do not support any 8-bit hardware, this patch only adds support for the 4-bit mode, but it can easily be built upon when the time comes. The 4-bit mode is electrically compatible with SD's 4-bit mode but the procedure for turning it on is different. This patch implements only the essential parts of the procedure as defined by the spec. Two additional steps are recommended but not compulsory. I am documenting them here so that there's a record. 1) A bus-test mechanism is implemented using dedicated mmc commands which allow for testing the functionality of the data bus at the electrical level. This is pretty paranoid and they way the commands work is not compatible with the mmc subsystem (they don't set valid CRC values). 2) MMC v4 cards can indicate they would like to draw more than the default amount of current in wide-bus modes. We currently will never switch the card into a higher draw mode. Supposedly, allowing the card to draw more current will let it perform better, but the specs seem to indicate that the card will function correctly without the mode change. Empirical testing supports this interpretation. Signed-off-by: Philip Langdale Signed-off-by: Pierre Ossman --- include/linux/mmc/protocol.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'include/linux/mmc/protocol.h') diff --git a/include/linux/mmc/protocol.h b/include/linux/mmc/protocol.h index 311b6547f561..45c51fd85786 100644 --- a/include/linux/mmc/protocol.h +++ b/include/linux/mmc/protocol.h @@ -256,6 +256,7 @@ struct _mmc_csd { * EXT_CSD fields */ +#define EXT_CSD_BUS_WIDTH 183 /* R/W */ #define EXT_CSD_HS_TIMING 185 /* R/W */ #define EXT_CSD_CARD_TYPE 196 /* RO */ @@ -270,6 +271,10 @@ struct _mmc_csd { #define EXT_CSD_CARD_TYPE_26 (1<<0) /* Card can run at 26MHz */ #define EXT_CSD_CARD_TYPE_52 (1<<1) /* Card can run at 52MHz */ +#define EXT_CSD_BUS_WIDTH_1 0 /* Card is in 1 bit mode */ +#define EXT_CSD_BUS_WIDTH_4 1 /* Card is in 4 bit mode */ +#define EXT_CSD_BUS_WIDTH_8 2 /* Card is in 8 bit mode */ + /* * MMC_SWITCH access modes */ -- cgit v1.2.3 From 7ccd266e676a3f0c6f8f897f58b684cac3dd1650 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Wed, 8 Nov 2006 23:03:10 +0100 Subject: mmc: Support for high speed SD cards Modern SD cards support a clock speed of 50 MHz. Make sure we test for this capability and do the song and dance required to activate it. Activating high speed support actually modifies the TRAN_SPEED field of the CSD. But as the spec says that the cards must report 50 MHz, we might as well skip re-reading the CSD. Signed-off-by: Pierre Ossman --- include/linux/mmc/protocol.h | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) (limited to 'include/linux/mmc/protocol.h') diff --git a/include/linux/mmc/protocol.h b/include/linux/mmc/protocol.h index 45c51fd85786..2dce60c43f4b 100644 --- a/include/linux/mmc/protocol.h +++ b/include/linux/mmc/protocol.h @@ -82,6 +82,7 @@ /* class 8 */ /* This is basically the same command as for MMC with some quirks. */ #define SD_SEND_RELATIVE_ADDR 3 /* bcr R6 */ +#define SD_SWITCH 6 /* adtc [31:0] See below R1 */ /* Application commands */ #define SD_APP_SET_BUS_WIDTH 6 /* ac [1:0] bus width R1 */ @@ -100,6 +101,19 @@ * [02:00] Command Set */ +/* + * SD_SWITCH argument format: + * + * [31] Check (0) or switch (1) + * [30:24] Reserved (0) + * [23:20] Function group 6 + * [19:16] Function group 5 + * [15:12] Function group 4 + * [11:8] Function group 3 + * [7:4] Function group 2 + * [3:0] Function group 1 + */ + /* MMC status in R1 Type @@ -284,6 +298,14 @@ struct _mmc_csd { #define MMC_SWITCH_MODE_CLEAR_BITS 0x02 /* Clear bits which are 1 in value */ #define MMC_SWITCH_MODE_WRITE_BYTE 0x03 /* Set target to value */ +/* + * SCR field definitions + */ + +#define SCR_SPEC_VER_0 0 /* Implements system specification 1.0 - 1.01 */ +#define SCR_SPEC_VER_1 1 /* Implements system specification 1.10 */ +#define SCR_SPEC_VER_2 2 /* Implements system specification 2.00 */ + /* * SD bus widths */ -- cgit v1.2.3