From 84b6826306119dc3c41ef9d7ed6c408112f63301 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Tue, 1 Dec 2009 21:12:27 +0000 Subject: regulator: Add notifier event on regulator disable The intended use case is for drivers which disable regulators to save power but need to do some work to restore the hardware state when restarting. If the supplies are not actually disabled due to board limits or sharing with other active devices this notifier allows the driver to avoid unneeded reinitialisation, particularly when used with runtime PM. Signed-off-by: Mark Brown --- include/linux/regulator/consumer.h | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'include/linux/regulator') diff --git a/include/linux/regulator/consumer.h b/include/linux/regulator/consumer.h index 030d92255c7a..28c9fd020d39 100644 --- a/include/linux/regulator/consumer.h +++ b/include/linux/regulator/consumer.h @@ -89,8 +89,9 @@ * REGULATION_OUT Regulator output is out of regulation. * FAIL Regulator output has failed. * OVER_TEMP Regulator over temp. - * FORCE_DISABLE Regulator shut down by software. + * FORCE_DISABLE Regulator forcibly shut down by software. * VOLTAGE_CHANGE Regulator voltage changed. + * DISABLE Regulator was disabled. * * NOTE: These events can be OR'ed together when passed into handler. */ @@ -102,6 +103,7 @@ #define REGULATOR_EVENT_OVER_TEMP 0x10 #define REGULATOR_EVENT_FORCE_DISABLE 0x20 #define REGULATOR_EVENT_VOLTAGE_CHANGE 0x40 +#define REGULATOR_EVENT_DISABLE 0x80 struct regulator; -- cgit v1.2.3 From 31aae2beeb3d601d556b6a8c39085940ad1e9f42 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Mon, 21 Dec 2009 12:21:52 +0000 Subject: regulator: Allow regulators to specify the time taken to ramp on enable Regulators may sometimes take longer to enable than the control operation used to do so, either because the regulator has ramp rate control used to limit inrush current or because the control operation is very fast (GPIO being the most common example of this). In order to ensure that consumers do not rely on the regulator before it is enabled provide an enable_time() operation and have the core delay for that time before returning to the caller. This is implemented as a function since the ramp rate may be specified in voltage per unit time and therefore the time depend on the configuration. In future it would be desirable to allow the bulk operations to run the delays for multiple enables in parallel but this is not currently supported. Signed-off-by: Mark Brown --- include/linux/regulator/driver.h | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'include/linux/regulator') diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index 31f2055eae28..592cd7c642c2 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -58,6 +58,9 @@ enum regulator_status { * @get_optimum_mode: Get the most efficient operating mode for the regulator * when running with the specified parameters. * + * @enable_time: Time taken for the regulator voltage output voltage to + * stabalise after being enabled, in microseconds. + * * @set_suspend_voltage: Set the voltage for the regulator when the system * is suspended. * @set_suspend_enable: Mark the regulator as enabled when the system is @@ -93,6 +96,9 @@ struct regulator_ops { int (*set_mode) (struct regulator_dev *, unsigned int mode); unsigned int (*get_mode) (struct regulator_dev *); + /* Time taken to enable the regulator */ + int (*enable_time) (struct regulator_dev *); + /* report regulator status ... most other accessors report * control inputs, this reports results of combining inputs * from Linux (and other sources) with the actual load. -- cgit v1.2.3 From eda79a3041a2cada0d4ee9491c99c3874b322356 Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Tue, 12 Jan 2010 12:25:13 +0200 Subject: regulator: Add 'start-up time' to fixed voltage regulators Add a field to specify a delay for the start-up time of a fixed voltage regulator. Signed-off-by: Adrian Hunter Acked-by: Mark Brown Signed-off-by: Liam Girdwood --- include/linux/regulator/fixed.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/linux/regulator') diff --git a/include/linux/regulator/fixed.h b/include/linux/regulator/fixed.h index e94a4a1c7c8a..ffd7d508e726 100644 --- a/include/linux/regulator/fixed.h +++ b/include/linux/regulator/fixed.h @@ -25,6 +25,7 @@ struct regulator_init_data; * @microvolts: Output voltage of regulator * @gpio: GPIO to use for enable control * set to -EINVAL if not used + * @startup_delay: Start-up time in microseconds * @enable_high: Polarity of enable GPIO * 1 = Active high, 0 = Active low * @enabled_at_boot: Whether regulator has been enabled at @@ -41,6 +42,7 @@ struct fixed_voltage_config { const char *supply_name; int microvolts; int gpio; + unsigned startup_delay; unsigned enable_high:1; unsigned enabled_at_boot:1; struct regulator_init_data *init_data; -- cgit v1.2.3 From a71b797fdc672714bfff1fdc142042a95e97d7ba Mon Sep 17 00:00:00 2001 From: Haojian Zhuang Date: Mon, 25 Jan 2010 10:24:09 -0500 Subject: regulator: enable max8649 regulator driver Signed-off-by: Haojian Zhuang Acked-by: Mark Brown Signed-off-by: Liam Girdwood --- include/linux/regulator/max8649.h | 44 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 44 insertions(+) create mode 100644 include/linux/regulator/max8649.h (limited to 'include/linux/regulator') diff --git a/include/linux/regulator/max8649.h b/include/linux/regulator/max8649.h new file mode 100644 index 000000000000..417d14ecd5cb --- /dev/null +++ b/include/linux/regulator/max8649.h @@ -0,0 +1,44 @@ +/* + * Interface of Maxim max8649 + * + * Copyright (C) 2009-2010 Marvell International Ltd. + * Haojian Zhuang + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __LINUX_REGULATOR_MAX8649_H +#define __LINUX_REGULATOR_MAX8649_H + +#include + +enum { + MAX8649_EXTCLK_26MHZ = 0, + MAX8649_EXTCLK_13MHZ, + MAX8649_EXTCLK_19MHZ, /* 19.2MHz */ +}; + +enum { + MAX8649_RAMP_32MV = 0, + MAX8649_RAMP_16MV, + MAX8649_RAMP_8MV, + MAX8649_RAMP_4MV, + MAX8649_RAMP_2MV, + MAX8649_RAMP_1MV, + MAX8649_RAMP_0_5MV, + MAX8649_RAMP_0_25MV, +}; + +struct max8649_platform_data { + struct regulator_init_data *regulator; + + unsigned mode:2; /* bit[1:0] = VID1,VID0 */ + unsigned extclk_freq:2; + unsigned extclk:1; + unsigned ramp_timing:3; + unsigned ramp_down:1; +}; + +#endif /* __LINUX_REGULATOR_MAX8649_H */ -- cgit v1.2.3